LXR linux/drivers/iio/adc/ad7923.c

   1/*
   2 * AD7904/AD7914/AD7923/AD7924 SPI ADC driver
   3 *
   4 * Copyright 2011 Analog Devices Inc (from AD7923 Driver)
   5 * Copyright 2012 CS Systemes d'Information
   6 *
   7 * Licensed under the GPL-2.
   8 */
   9
  10#include <linux/device.h>
  11#include <linux/kernel.h>
  12#include <linux/slab.h>
  13#include <linux/sysfs.h>
  14#include <linux/spi/spi.h>
  15#include <linux/regulator/consumer.h>
  16#include <linux/err.h>
  17#include <linux/delay.h>
  18#include <linux/module.h>
  19#include <linux/interrupt.h>
  20
  21#include <linux/iio/iio.h>
  22#include <linux/iio/sysfs.h>
  23#include <linux/iio/buffer.h>
  24#include <linux/iio/trigger_consumer.h>
  25#include <linux/iio/triggered_buffer.h>
  26
  27#define AD7923_WRITE_CR         (1 << 11)       /* write control register */
  28#define AD7923_RANGE            (1 << 1)        /* range to REFin */
  29#define AD7923_CODING           (1 << 0)        /* coding is straight binary */
  30#define AD7923_PM_MODE_AS       (1)             /* auto shutdown */
  31#define AD7923_PM_MODE_FS       (2)             /* full shutdown */
  32#define AD7923_PM_MODE_OPS      (3)             /* normal operation */
  33#define AD7923_CHANNEL_0        (0)             /* analog input 0 */
  34#define AD7923_CHANNEL_1        (1)             /* analog input 1 */
  35#define AD7923_CHANNEL_2        (2)             /* analog input 2 */
  36#define AD7923_CHANNEL_3        (3)             /* analog input 3 */
  37#define AD7923_SEQUENCE_OFF     (0)             /* no sequence fonction */
  38#define AD7923_SEQUENCE_PROTECT (2)             /* no interrupt write cycle */
  39#define AD7923_SEQUENCE_ON      (3)             /* continuous sequence */
  40
  41#define AD7923_MAX_CHAN         4
  42
  43#define AD7923_PM_MODE_WRITE(mode)      (mode << 4)     /* write mode */
  44#define AD7923_CHANNEL_WRITE(channel)   (channel << 6)  /* write channel */
  45#define AD7923_SEQUENCE_WRITE(sequence) (((sequence & 1) << 3) \
  46                                        + ((sequence & 2) << 9))
  47                                                /* write sequence fonction */
  48/* left shift for CR : bit 11 transmit in first */
  49#define AD7923_SHIFT_REGISTER   4
  50
  51/* val = value, dec = left shift, bits = number of bits of the mask */
  52#define EXTRACT(val, dec, bits)         ((val >> dec) & ((1 << bits) - 1))
  53
  54struct ad7923_state {
  55        struct spi_device               *spi;
  56        struct spi_transfer             ring_xfer[5];
  57        struct spi_transfer             scan_single_xfer[2];
  58        struct spi_message              ring_msg;
  59        struct spi_message              scan_single_msg;
  60
  61        struct regulator                *reg;
  62
  63        unsigned int                    settings;
  64
  65        /*
  66         * DMA (thus cache coherency maintenance) requires the
  67         * transfer buffers to live in their own cache lines.
  68         */
  69        __be16                          rx_buf[4] ____cacheline_aligned;
  70        __be16                          tx_buf[4];
  71};
  72
  73struct ad7923_chip_info {
  74        const struct iio_chan_spec *channels;
  75        unsigned int num_channels;
  76};
  77
  78enum ad7923_id {
  79        AD7904,
  80        AD7914,
  81        AD7924,
  82};
  83
  84#define AD7923_V_CHAN(index, bits)                                      \
  85        {                                                               \
  86                .type = IIO_VOLTAGE,                                    \
  87                .indexed = 1,                                           \
  88                .channel = index,                                       \
  89                .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),           \
  90                .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),   \
  91                .address = index,                                       \
  92                .scan_index = index,                                    \
  93                .scan_type = {                                          \
  94                        .sign = 'u',                                    \
  95                        .realbits = (bits),                             \
  96                        .storagebits = 16,                              \
  97                        .endianness = IIO_BE,                           \
  98                },                                                      \
  99        }
 100
 101#define DECLARE_AD7923_CHANNELS(name, bits) \
 102const struct iio_chan_spec name ## _channels[] = { \
 103        AD7923_V_CHAN(0, bits), \
 104        AD7923_V_CHAN(1, bits), \
 105        AD7923_V_CHAN(2, bits), \
 106        AD7923_V_CHAN(3, bits), \
 107        IIO_CHAN_SOFT_TIMESTAMP(4), \
 108}
 109
 110static DECLARE_AD7923_CHANNELS(ad7904, 8);
 111static DECLARE_AD7923_CHANNELS(ad7914, 10);
 112static DECLARE_AD7923_CHANNELS(ad7924, 12);
 113
 114static const struct ad7923_chip_info ad7923_chip_info[] = {
 115        [AD7904] = {
 116                .channels = ad7904_channels,
 117                .num_channels = ARRAY_SIZE(ad7904_channels),
 118        },
 119        [AD7914] = {
 120                .channels = ad7914_channels,
 121                .num_channels = ARRAY_SIZE(ad7914_channels),
 122        },
 123        [AD7924] = {
 124                .channels = ad7924_channels,
 125                .num_channels = ARRAY_SIZE(ad7924_channels),
 126        },
 127};
 128
 129/**
 130 * ad7923_update_scan_mode() setup the spi transfer buffer for the new scan mask
 131 **/
 132static int ad7923_update_scan_mode(struct iio_dev *indio_dev,
 133        const unsigned long *active_scan_mask)
 134{
 135        struct ad7923_state *st = iio_priv(indio_dev);
 136        int i, cmd, len;
 137
 138        len = 0;
 139        for_each_set_bit(i, active_scan_mask, AD7923_MAX_CHAN) {
 140                cmd = AD7923_WRITE_CR | AD7923_CHANNEL_WRITE(i) |
 141                        AD7923_SEQUENCE_WRITE(AD7923_SEQUENCE_OFF) |
 142                        st->settings;
 143                cmd <<= AD7923_SHIFT_REGISTER;
 144                st->tx_buf[len++] = cpu_to_be16(cmd);
 145        }
 146        /* build spi ring message */
 147        st->ring_xfer[0].tx_buf = &st->tx_buf[0];
 148        st->ring_xfer[0].len = len;
 149        st->ring_xfer[0].cs_change = 1;
 150
 151        spi_message_init(&st->ring_msg);
 152        spi_message_add_tail(&st->ring_xfer[0], &st->ring_msg);
 153
 154        for (i = 0; i < len; i++) {
 155                st->ring_xfer[i + 1].rx_buf = &st->rx_buf[i];
 156                st->ring_xfer[i + 1].len = 2;
 157                st->ring_xfer[i + 1].cs_change = 1;
 158                spi_message_add_tail(&st->ring_xfer[i + 1], &st->ring_msg);
 159        }
 160        /* make sure last transfer cs_change is not set */
 161        st->ring_xfer[i + 1].cs_change = 0;
 162
 163        return 0;
 164}
 165
 166/**
 167 * ad7923_trigger_handler() bh of trigger launched polling to ring buffer
 168 *
 169 * Currently there is no option in this driver to disable the saving of
 170 * timestamps within the ring.
 171 **/
 172static irqreturn_t ad7923_trigger_handler(int irq, void *p)
 173{
 174        struct iio_poll_func *pf = p;
 175        struct iio_dev *indio_dev = pf->indio_dev;
 176        struct ad7923_state *st = iio_priv(indio_dev);
 177        int b_sent;
 178
 179        b_sent = spi_sync(st->spi, &st->ring_msg);
 180        if (b_sent)
 181                goto done;
 182
 183        iio_push_to_buffers_with_timestamp(indio_dev, st->rx_buf,
 184                iio_get_time_ns(indio_dev));
 185
 186done:
 187        iio_trigger_notify_done(indio_dev->trig);
 188
 189        return IRQ_HANDLED;
 190}
 191
 192static int ad7923_scan_direct(struct ad7923_state *st, unsigned ch)
 193{
 194        int ret, cmd;
 195
 196        cmd = AD7923_WRITE_CR | AD7923_CHANNEL_WRITE(ch) |
 197                AD7923_SEQUENCE_WRITE(AD7923_SEQUENCE_OFF) |
 198                st->settings;
 199        cmd <<= AD7923_SHIFT_REGISTER;
 200        st->tx_buf[0] = cpu_to_be16(cmd);
 201
 202        ret = spi_sync(st->spi, &st->scan_single_msg);
 203        if (ret)
 204                return ret;
 205
 206        return be16_to_cpu(st->rx_buf[0]);
 207}
 208
 209static int ad7923_get_range(struct ad7923_state *st)
 210{
 211        int vref;
 212
 213        vref = regulator_get_voltage(st->reg);
 214        if (vref < 0)
 215                return vref;
 216
 217        vref /= 1000;
 218
 219        if (!(st->settings & AD7923_RANGE))
 220                vref *= 2;
 221
 222        return vref;
 223}
 224
 225static int ad7923_read_raw(struct iio_dev *indio_dev,
 226                           struct iio_chan_spec const *chan,
 227                           int *val,
 228                           int *val2,
 229                           long m)
 230{
 231        int ret;
 232        struct ad7923_state *st = iio_priv(indio_dev);
 233
 234        switch (m) {
 235        case IIO_CHAN_INFO_RAW:
 236                ret = iio_device_claim_direct_mode(indio_dev);
 237                if (ret)
 238                        return ret;
 239                ret = ad7923_scan_direct(st, chan->address);
 240                iio_device_release_direct_mode(indio_dev);
 241
 242                if (ret < 0)
 243                        return ret;
 244
 245                if (chan->address == EXTRACT(ret, 12, 4))
 246                        *val = EXTRACT(ret, 0, 12);
 247                else
 248                        return -EIO;
 249
 250                return IIO_VAL_INT;
 251        case IIO_CHAN_INFO_SCALE:
 252                ret = ad7923_get_range(st);
 253                if (ret < 0)
 254                        return ret;
 255                *val = ret;
 256                *val2 = chan->scan_type.realbits;
 257                return IIO_VAL_FRACTIONAL_LOG2;
 258        }
 259        return -EINVAL;
 260}
 261
 262static const struct iio_info ad7923_info = {
 263        .read_raw = &ad7923_read_raw,
 264        .update_scan_mode = ad7923_update_scan_mode,
 265};
 266
 267static int ad7923_probe(struct spi_device *spi)
 268{
 269        struct ad7923_state *st;
 270        struct iio_dev *indio_dev;
 271        const struct ad7923_chip_info *info;
 272        int ret;
 273
 274        indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st));
 275        if (indio_dev == NULL)
 276                return -ENOMEM;
 277
 278        st = iio_priv(indio_dev);
 279
 280        spi_set_drvdata(spi, indio_dev);
 281
 282        st->spi = spi;
 283        st->settings = AD7923_CODING | AD7923_RANGE |
 284                        AD7923_PM_MODE_WRITE(AD7923_PM_MODE_OPS);
 285
 286        info = &ad7923_chip_info[spi_get_device_id(spi)->driver_data];
 287
 288        indio_dev->name = spi_get_device_id(spi)->name;
 289        indio_dev->dev.parent = &spi->dev;
 290        indio_dev->dev.of_node = spi->dev.of_node;
 291        indio_dev->modes = INDIO_DIRECT_MODE;
 292        indio_dev->channels = info->channels;
 293        indio_dev->num_channels = info->num_channels;
 294        indio_dev->info = &ad7923_info;
 295
 296        /* Setup default message */
 297
 298        st->scan_single_xfer[0].tx_buf = &st->tx_buf[0];
 299        st->scan_single_xfer[0].len = 2;
 300        st->scan_single_xfer[0].cs_change = 1;
 301        st->scan_single_xfer[1].rx_buf = &st->rx_buf[0];
 302        st->scan_single_xfer[1].len = 2;
 303
 304        spi_message_init(&st->scan_single_msg);
 305        spi_message_add_tail(&st->scan_single_xfer[0], &st->scan_single_msg);
 306        spi_message_add_tail(&st->scan_single_xfer[1], &st->scan_single_msg);
 307
 308        st->reg = devm_regulator_get(&spi->dev, "refin");
 309        if (IS_ERR(st->reg))
 310                return PTR_ERR(st->reg);
 311
 312        ret = regulator_enable(st->reg);
 313        if (ret)
 314                return ret;
 315
 316        ret = iio_triggered_buffer_setup(indio_dev, NULL,
 317                        &ad7923_trigger_handler, NULL);
 318        if (ret)
 319                goto error_disable_reg;
 320
 321        ret = iio_device_register(indio_dev);
 322        if (ret)
 323                goto error_cleanup_ring;
 324
 325        return 0;
 326
 327error_cleanup_ring:
 328        iio_triggered_buffer_cleanup(indio_dev);
 329error_disable_reg:
 330        regulator_disable(st->reg);
 331
 332        return ret;
 333}
 334
 335static int ad7923_remove(struct spi_device *spi)
 336{
 337        struct iio_dev *indio_dev = spi_get_drvdata(spi);
 338        struct ad7923_state *st = iio_priv(indio_dev);
 339
 340        iio_device_unregister(indio_dev);
 341        iio_triggered_buffer_cleanup(indio_dev);
 342        regulator_disable(st->reg);
 343
 344        return 0;
 345}
 346
 347static const struct spi_device_id ad7923_id[] = {
 348        {"ad7904", AD7904},
 349        {"ad7914", AD7914},
 350        {"ad7923", AD7924},
 351        {"ad7924", AD7924},
 352        {}
 353};
 354MODULE_DEVICE_TABLE(spi, ad7923_id);
 355
 356static struct spi_driver ad7923_driver = {
 357        .driver = {
 358                .name   = "ad7923",
 359        },
 360        .probe          = ad7923_probe,
 361        .remove         = ad7923_remove,
 362        .id_table       = ad7923_id,
 363};
 364module_spi_driver(ad7923_driver);
 365
 366MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>");
 367MODULE_AUTHOR("Patrick Vasseur <patrick.vasseur@c-s.fr>");
 368MODULE_DESCRIPTION("Analog Devices AD7904/AD7914/AD7923/AD7924 ADC");
 369MODULE_LICENSE("GPL v2");
 370