linux/arch/blackfin/mach-bf561/boards/cm_bf561.c
<<
>>
Prefs
   1/*
   2 * Copyright 2004-2009 Analog Devices Inc.
   3 *               2008-2009 Bluetechnix
   4 *               2005 National ICT Australia (NICTA)
   5 *                    Aidan Williams <aidan@nicta.com.au>
   6 *
   7 * Licensed under the GPL-2 or later.
   8 */
   9
  10#include <linux/device.h>
  11#include <linux/platform_device.h>
  12#include <linux/mtd/mtd.h>
  13#include <linux/mtd/partitions.h>
  14#include <linux/spi/spi.h>
  15#include <linux/spi/flash.h>
  16#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
  17#include <linux/usb/isp1362.h>
  18#endif
  19#include <linux/ata_platform.h>
  20#include <linux/irq.h>
  21#include <linux/gpio.h>
  22#include <asm/dma.h>
  23#include <asm/bfin5xx_spi.h>
  24#include <asm/portmux.h>
  25#include <asm/dpmc.h>
  26#include <linux/mtd/physmap.h>
  27
  28/*
  29 * Name the Board for the /proc/cpuinfo
  30 */
  31const char bfin_board_name[] = "Bluetechnix CM BF561";
  32
  33#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
  34/* all SPI peripherals info goes here */
  35
  36#if IS_ENABLED(CONFIG_MTD_M25P80)
  37static struct mtd_partition bfin_spi_flash_partitions[] = {
  38        {
  39                .name = "bootloader(spi)",
  40                .size = 0x00020000,
  41                .offset = 0,
  42                .mask_flags = MTD_CAP_ROM
  43        }, {
  44                .name = "linux kernel(spi)",
  45                .size = 0xe0000,
  46                .offset = 0x20000
  47        }, {
  48                .name = "file system(spi)",
  49                .size = 0x700000,
  50                .offset = 0x00100000,
  51        }
  52};
  53
  54static struct flash_platform_data bfin_spi_flash_data = {
  55        .name = "m25p80",
  56        .parts = bfin_spi_flash_partitions,
  57        .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
  58        .type = "m25p64",
  59};
  60
  61/* SPI flash chip (m25p64) */
  62static struct bfin5xx_spi_chip spi_flash_chip_info = {
  63        .enable_dma = 0,         /* use dma transfer with this chip*/
  64};
  65#endif
  66
  67static struct spi_board_info bfin_spi_board_info[] __initdata = {
  68#if IS_ENABLED(CONFIG_MTD_M25P80)
  69        {
  70                /* the modalias must be the same as spi device driver name */
  71                .modalias = "m25p80", /* Name of spi_driver for this device */
  72                .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
  73                .bus_num = 0, /* Framework bus number */
  74                .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
  75                .platform_data = &bfin_spi_flash_data,
  76                .controller_data = &spi_flash_chip_info,
  77                .mode = SPI_MODE_3,
  78        },
  79#endif
  80
  81#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
  82        {
  83                .modalias = "ad183x",
  84                .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
  85                .bus_num = 0,
  86                .chip_select = 4,
  87        },
  88#endif
  89#if IS_ENABLED(CONFIG_MMC_SPI)
  90        {
  91                .modalias = "mmc_spi",
  92                .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
  93                .bus_num = 0,
  94                .chip_select = 1,
  95                .mode = SPI_MODE_3,
  96        },
  97#endif
  98};
  99
 100/* SPI (0) */
 101static struct resource bfin_spi0_resource[] = {
 102        [0] = {
 103                .start = SPI0_REGBASE,
 104                .end   = SPI0_REGBASE + 0xFF,
 105                .flags = IORESOURCE_MEM,
 106        },
 107        [1] = {
 108                .start = CH_SPI,
 109                .end   = CH_SPI,
 110                .flags = IORESOURCE_DMA,
 111        },
 112        [2] = {
 113                .start = IRQ_SPI,
 114                .end   = IRQ_SPI,
 115                .flags = IORESOURCE_IRQ,
 116        },
 117};
 118
 119/* SPI controller data */
 120static struct bfin5xx_spi_master bfin_spi0_info = {
 121        .num_chipselect = 8,
 122        .enable_dma = 1,  /* master has the ability to do dma transfer */
 123        .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 124};
 125
 126static struct platform_device bfin_spi0_device = {
 127        .name = "bfin-spi",
 128        .id = 0, /* Bus number */
 129        .num_resources = ARRAY_SIZE(bfin_spi0_resource),
 130        .resource = bfin_spi0_resource,
 131        .dev = {
 132                .platform_data = &bfin_spi0_info, /* Passed to driver */
 133        },
 134};
 135#endif  /* spi master and devices */
 136
 137
 138#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 139static struct platform_device hitachi_fb_device = {
 140        .name = "hitachi-tx09",
 141};
 142#endif
 143
 144
 145#if IS_ENABLED(CONFIG_SMC91X)
 146#include <linux/smc91x.h>
 147
 148static struct smc91x_platdata smc91x_info = {
 149        .flags = SMC91X_USE_32BIT | SMC91X_NOWAIT,
 150        .leda = RPC_LED_100_10,
 151        .ledb = RPC_LED_TX_RX,
 152};
 153
 154static struct resource smc91x_resources[] = {
 155        {
 156                .name = "smc91x-regs",
 157                .start = 0x28000300,
 158                .end = 0x28000300 + 16,
 159                .flags = IORESOURCE_MEM,
 160        }, {
 161                .start = IRQ_PF0,
 162                .end = IRQ_PF0,
 163                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 164        },
 165};
 166static struct platform_device smc91x_device = {
 167        .name = "smc91x",
 168        .id = 0,
 169        .num_resources = ARRAY_SIZE(smc91x_resources),
 170        .resource = smc91x_resources,
 171        .dev    = {
 172                .platform_data  = &smc91x_info,
 173        },
 174};
 175#endif
 176
 177#if IS_ENABLED(CONFIG_SMSC911X)
 178#include <linux/smsc911x.h>
 179
 180static struct resource smsc911x_resources[] = {
 181        {
 182                .name = "smsc911x-memory",
 183                .start = 0x24008000,
 184                .end = 0x24008000 + 0xFF,
 185                .flags = IORESOURCE_MEM,
 186        },
 187        {
 188                .start = IRQ_PF43,
 189                .end = IRQ_PF43,
 190                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 191        },
 192};
 193
 194static struct smsc911x_platform_config smsc911x_config = {
 195        .flags = SMSC911X_USE_16BIT,
 196        .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
 197        .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
 198        .phy_interface = PHY_INTERFACE_MODE_MII,
 199};
 200
 201static struct platform_device smsc911x_device = {
 202        .name = "smsc911x",
 203        .id = 0,
 204        .num_resources = ARRAY_SIZE(smsc911x_resources),
 205        .resource = smsc911x_resources,
 206        .dev = {
 207                .platform_data = &smsc911x_config,
 208        },
 209};
 210#endif
 211
 212#if IS_ENABLED(CONFIG_USB_NET2272)
 213static struct resource net2272_bfin_resources[] = {
 214        {
 215                .start = 0x24000000,
 216                .end = 0x24000000 + 0x100,
 217                .flags = IORESOURCE_MEM,
 218        }, {
 219                .start = IRQ_PF45,
 220                .end = IRQ_PF45,
 221                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 222        },
 223};
 224
 225static struct platform_device net2272_bfin_device = {
 226        .name = "net2272",
 227        .id = -1,
 228        .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 229        .resource = net2272_bfin_resources,
 230};
 231#endif
 232
 233#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 234static struct resource isp1362_hcd_resources[] = {
 235        {
 236                .start = 0x24008000,
 237                .end = 0x24008000,
 238                .flags = IORESOURCE_MEM,
 239        }, {
 240                .start = 0x24008004,
 241                .end = 0x24008004,
 242                .flags = IORESOURCE_MEM,
 243        }, {
 244                .start = IRQ_PF47,
 245                .end = IRQ_PF47,
 246                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 247        },
 248};
 249
 250static struct isp1362_platform_data isp1362_priv = {
 251        .sel15Kres = 1,
 252        .clknotstop = 0,
 253        .oc_enable = 0,
 254        .int_act_high = 0,
 255        .int_edge_triggered = 0,
 256        .remote_wakeup_connected = 0,
 257        .no_power_switching = 1,
 258        .power_switching_mode = 0,
 259};
 260
 261static struct platform_device isp1362_hcd_device = {
 262        .name = "isp1362-hcd",
 263        .id = 0,
 264        .dev = {
 265                .platform_data = &isp1362_priv,
 266        },
 267        .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
 268        .resource = isp1362_hcd_resources,
 269};
 270#endif
 271
 272#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 273#ifdef CONFIG_SERIAL_BFIN_UART0
 274static struct resource bfin_uart0_resources[] = {
 275        {
 276                .start = BFIN_UART_THR,
 277                .end = BFIN_UART_GCTL+2,
 278                .flags = IORESOURCE_MEM,
 279        },
 280        {
 281                .start = IRQ_UART_TX,
 282                .end = IRQ_UART_TX,
 283                .flags = IORESOURCE_IRQ,
 284        },
 285        {
 286                .start = IRQ_UART_RX,
 287                .end = IRQ_UART_RX,
 288                .flags = IORESOURCE_IRQ,
 289        },
 290        {
 291                .start = IRQ_UART_ERROR,
 292                .end = IRQ_UART_ERROR,
 293                .flags = IORESOURCE_IRQ,
 294        },
 295        {
 296                .start = CH_UART_TX,
 297                .end = CH_UART_TX,
 298                .flags = IORESOURCE_DMA,
 299        },
 300        {
 301                .start = CH_UART_RX,
 302                .end = CH_UART_RX,
 303                .flags = IORESOURCE_DMA,
 304        },
 305};
 306
 307static unsigned short bfin_uart0_peripherals[] = {
 308        P_UART0_TX, P_UART0_RX, 0
 309};
 310
 311static struct platform_device bfin_uart0_device = {
 312        .name = "bfin-uart",
 313        .id = 0,
 314        .num_resources = ARRAY_SIZE(bfin_uart0_resources),
 315        .resource = bfin_uart0_resources,
 316        .dev = {
 317                .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
 318        },
 319};
 320#endif
 321#endif
 322
 323#if IS_ENABLED(CONFIG_BFIN_SIR)
 324#ifdef CONFIG_BFIN_SIR0
 325static struct resource bfin_sir0_resources[] = {
 326        {
 327                .start = 0xFFC00400,
 328                .end = 0xFFC004FF,
 329                .flags = IORESOURCE_MEM,
 330        },
 331        {
 332                .start = IRQ_UART0_RX,
 333                .end = IRQ_UART0_RX+1,
 334                .flags = IORESOURCE_IRQ,
 335        },
 336        {
 337                .start = CH_UART0_RX,
 338                .end = CH_UART0_RX+1,
 339                .flags = IORESOURCE_DMA,
 340        },
 341};
 342
 343static struct platform_device bfin_sir0_device = {
 344        .name = "bfin_sir",
 345        .id = 0,
 346        .num_resources = ARRAY_SIZE(bfin_sir0_resources),
 347        .resource = bfin_sir0_resources,
 348};
 349#endif
 350#endif
 351
 352#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 353#define PATA_INT        IRQ_PF46
 354
 355static struct pata_platform_info bfin_pata_platform_data = {
 356        .ioport_shift = 2,
 357};
 358
 359static struct resource bfin_pata_resources[] = {
 360        {
 361                .start = 0x2400C000,
 362                .end = 0x2400C001F,
 363                .flags = IORESOURCE_MEM,
 364        },
 365        {
 366                .start = 0x2400D018,
 367                .end = 0x2400D01B,
 368                .flags = IORESOURCE_MEM,
 369        },
 370        {
 371                .start = PATA_INT,
 372                .end = PATA_INT,
 373                .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 374        },
 375};
 376
 377static struct platform_device bfin_pata_device = {
 378        .name = "pata_platform",
 379        .id = -1,
 380        .num_resources = ARRAY_SIZE(bfin_pata_resources),
 381        .resource = bfin_pata_resources,
 382        .dev = {
 383                .platform_data = &bfin_pata_platform_data,
 384        }
 385};
 386#endif
 387
 388#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 389static struct mtd_partition para_partitions[] = {
 390        {
 391                .name       = "bootloader(nor)",
 392                .size       = 0x40000,
 393                .offset     = 0,
 394        }, {
 395                .name       = "linux kernel(nor)",
 396                .size       = 0x100000,
 397                .offset     = MTDPART_OFS_APPEND,
 398        }, {
 399                .name       = "file system(nor)",
 400                .size       = MTDPART_SIZ_FULL,
 401                .offset     = MTDPART_OFS_APPEND,
 402        }
 403};
 404
 405static struct physmap_flash_data para_flash_data = {
 406        .width      = 2,
 407        .parts      = para_partitions,
 408        .nr_parts   = ARRAY_SIZE(para_partitions),
 409};
 410
 411static struct resource para_flash_resource = {
 412        .start = 0x20000000,
 413        .end   = 0x207fffff,
 414        .flags = IORESOURCE_MEM,
 415};
 416
 417static struct platform_device para_flash_device = {
 418        .name          = "physmap-flash",
 419        .id            = 0,
 420        .dev = {
 421                .platform_data = &para_flash_data,
 422        },
 423        .num_resources = 1,
 424        .resource      = &para_flash_resource,
 425};
 426#endif
 427
 428static const unsigned int cclk_vlev_datasheet[] =
 429{
 430        VRPAIR(VLEV_085, 250000000),
 431        VRPAIR(VLEV_090, 300000000),
 432        VRPAIR(VLEV_095, 313000000),
 433        VRPAIR(VLEV_100, 350000000),
 434        VRPAIR(VLEV_105, 400000000),
 435        VRPAIR(VLEV_110, 444000000),
 436        VRPAIR(VLEV_115, 450000000),
 437        VRPAIR(VLEV_120, 475000000),
 438        VRPAIR(VLEV_125, 500000000),
 439        VRPAIR(VLEV_130, 600000000),
 440};
 441
 442static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
 443        .tuple_tab = cclk_vlev_datasheet,
 444        .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
 445        .vr_settling_time = 25 /* us */,
 446};
 447
 448static struct platform_device bfin_dpmc = {
 449        .name = "bfin dpmc",
 450        .dev = {
 451                .platform_data = &bfin_dmpc_vreg_data,
 452        },
 453};
 454
 455static struct platform_device *cm_bf561_devices[] __initdata = {
 456
 457        &bfin_dpmc,
 458
 459#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 460        &hitachi_fb_device,
 461#endif
 462
 463#if IS_ENABLED(CONFIG_SERIAL_BFIN)
 464#ifdef CONFIG_SERIAL_BFIN_UART0
 465        &bfin_uart0_device,
 466#endif
 467#endif
 468
 469#if IS_ENABLED(CONFIG_BFIN_SIR)
 470#ifdef CONFIG_BFIN_SIR0
 471        &bfin_sir0_device,
 472#endif
 473#endif
 474
 475#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 476        &isp1362_hcd_device,
 477#endif
 478
 479#if IS_ENABLED(CONFIG_SMC91X)
 480        &smc91x_device,
 481#endif
 482
 483#if IS_ENABLED(CONFIG_SMSC911X)
 484        &smsc911x_device,
 485#endif
 486
 487#if IS_ENABLED(CONFIG_USB_NET2272)
 488        &net2272_bfin_device,
 489#endif
 490
 491#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 492        &bfin_spi0_device,
 493#endif
 494
 495#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 496        &bfin_pata_device,
 497#endif
 498
 499#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
 500        &para_flash_device,
 501#endif
 502};
 503
 504static int __init net2272_init(void)
 505{
 506#if IS_ENABLED(CONFIG_USB_NET2272)
 507        int ret;
 508
 509        ret = gpio_request(GPIO_PF46, "net2272");
 510        if (ret)
 511                return ret;
 512
 513        /* Reset USB Chip, PF46 */
 514        gpio_direction_output(GPIO_PF46, 0);
 515        mdelay(2);
 516        gpio_set_value(GPIO_PF46, 1);
 517#endif
 518
 519        return 0;
 520}
 521
 522static int __init cm_bf561_init(void)
 523{
 524        printk(KERN_INFO "%s(): registering device resources\n", __func__);
 525        platform_add_devices(cm_bf561_devices, ARRAY_SIZE(cm_bf561_devices));
 526#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 527        spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 528#endif
 529
 530#if IS_ENABLED(CONFIG_PATA_PLATFORM)
 531        irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 532#endif
 533
 534        if (net2272_init())
 535                pr_warning("unable to configure net2272; it probably won't work\n");
 536
 537        return 0;
 538}
 539
 540arch_initcall(cm_bf561_init);
 541
 542static struct platform_device *cm_bf561_early_devices[] __initdata = {
 543#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
 544#ifdef CONFIG_SERIAL_BFIN_UART0
 545        &bfin_uart0_device,
 546#endif
 547#endif
 548};
 549
 550void __init native_machine_early_platform_add_devices(void)
 551{
 552        printk(KERN_INFO "register early platform devices\n");
 553        early_platform_add_devices(cm_bf561_early_devices,
 554                ARRAY_SIZE(cm_bf561_early_devices));
 555}
 556