1/* ------------------------------------------------------------------------- */ 2/* i2c-iop3xx.h algorithm driver definitions private to i2c-iop3xx.c */ 3/* ------------------------------------------------------------------------- */ 4/* Copyright (C) 2003 Peter Milne, D-TACQ Solutions Ltd 5 * <Peter dot Milne at D hyphen TACQ dot com> 6 7 This program is free software; you can redistribute it and/or modify 8 it under the terms of the GNU General Public License as published by 9 the Free Software Foundation, version 2. 10 11 This program is distributed in the hope that it will be useful, 12 but WITHOUT ANY WARRANTY; without even the implied warranty of 13 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 14 GNU General Public License for more details. */ 15/* ------------------------------------------------------------------------- */ 16 17 18#ifndef I2C_IOP3XX_H 19#define I2C_IOP3XX_H 1 20 21/* 22 * iop321 hardware bit definitions 23 */ 24#define IOP3XX_ICR_FAST_MODE 0x8000 /* 1=400kBps, 0=100kBps */ 25#define IOP3XX_ICR_UNIT_RESET 0x4000 /* 1=RESET */ 26#define IOP3XX_ICR_SAD_IE 0x2000 /* 1=Slave Detect Interrupt Enable */ 27#define IOP3XX_ICR_ALD_IE 0x1000 /* 1=Arb Loss Detect Interrupt Enable */ 28#define IOP3XX_ICR_SSD_IE 0x0800 /* 1=Slave STOP Detect Interrupt Enable */ 29#define IOP3XX_ICR_BERR_IE 0x0400 /* 1=Bus Error Interrupt Enable */ 30#define IOP3XX_ICR_RXFULL_IE 0x0200 /* 1=Receive Full Interrupt Enable */ 31#define IOP3XX_ICR_TXEMPTY_IE 0x0100 /* 1=Transmit Empty Interrupt Enable */ 32#define IOP3XX_ICR_GCD 0x0080 /* 1=General Call Disable */ 33/* 34 * IOP3XX_ICR_GCD: 1 disables response as slave. "This bit must be set 35 * when sending a master mode general call message from the I2C unit" 36 */ 37#define IOP3XX_ICR_UE 0x0040 /* 1=Unit Enable */ 38/* 39 * "NOTE: To avoid I2C bus integrity problems, 40 * the user needs to ensure that the GPIO Output Data Register - 41 * GPOD bits associated with an I2C port are cleared prior to setting 42 * the enable bit for that I2C serial port. 43 * The user prepares to enable I2C port 0 and 44 * I2C port 1 by clearing GPOD bits 7:6 and GPOD bits 5:4, respectively. 45 */ 46#define IOP3XX_ICR_SCLEN 0x0020 /* 1=SCL enable for master mode */ 47#define IOP3XX_ICR_MABORT 0x0010 /* 1=Send a STOP with no data 48 * NB TBYTE must be clear */ 49#define IOP3XX_ICR_TBYTE 0x0008 /* 1=Send/Receive a byte. i2c clears */ 50#define IOP3XX_ICR_NACK 0x0004 /* 1=reply with NACK */ 51#define IOP3XX_ICR_MSTOP 0x0002 /* 1=send a STOP after next data byte */ 52#define IOP3XX_ICR_MSTART 0x0001 /* 1=initiate a START */ 53 54 55#define IOP3XX_ISR_BERRD 0x0400 /* 1=BUS ERROR Detected */ 56#define IOP3XX_ISR_SAD 0x0200 /* 1=Slave ADdress Detected */ 57#define IOP3XX_ISR_GCAD 0x0100 /* 1=General Call Address Detected */ 58#define IOP3XX_ISR_RXFULL 0x0080 /* 1=Receive Full */ 59#define IOP3XX_ISR_TXEMPTY 0x0040 /* 1=Transmit Empty */ 60#define IOP3XX_ISR_ALD 0x0020 /* 1=Arbitration Loss Detected */ 61#define IOP3XX_ISR_SSD 0x0010 /* 1=Slave STOP Detected */ 62#define IOP3XX_ISR_BBUSY 0x0008 /* 1=Bus BUSY */ 63#define IOP3XX_ISR_UNITBUSY 0x0004 /* 1=Unit Busy */ 64#define IOP3XX_ISR_NACK 0x0002 /* 1=Unit Rx or Tx a NACK */ 65#define IOP3XX_ISR_RXREAD 0x0001 /* 1=READ 0=WRITE (R/W bit of slave addr */ 66 67#define IOP3XX_ISR_CLEARBITS 0x07f0 68 69#define IOP3XX_ISAR_SAMASK 0x007f 70 71#define IOP3XX_IDBR_MASK 0x00ff 72 73#define IOP3XX_IBMR_SCL 0x0002 74#define IOP3XX_IBMR_SDA 0x0001 75 76#define IOP3XX_GPOD_I2C0 0x00c0 /* clear these bits to enable ch0 */ 77#define IOP3XX_GPOD_I2C1 0x0030 /* clear these bits to enable ch1 */ 78 79#define MYSAR 0 /* default slave address */ 80 81#define I2C_ERR 321 82#define I2C_ERR_BERR (I2C_ERR+0) 83#define I2C_ERR_ALD (I2C_ERR+1) 84 85 86#define CR_OFFSET 0 87#define SR_OFFSET 0x4 88#define SAR_OFFSET 0x8 89#define DBR_OFFSET 0xc 90#define CCR_OFFSET 0x10 91#define BMR_OFFSET 0x14 92 93#define IOP3XX_I2C_IO_SIZE 0x18 94 95struct i2c_algo_iop3xx_data { 96 void __iomem *ioaddr; 97 wait_queue_head_t waitq; 98 spinlock_t lock; 99 u32 SR_enabled, SR_received; 100 int id; 101}; 102 103#endif /* I2C_IOP3XX_H */ 104