/*
 * twl4030.h - header for TWL4030 PM and audio CODEC device
 *
 * Copyright (C) 2005-2006 Texas Instruments, Inc.
 *
 * Based on tlv320aic23.c:
 * Copyright (c) by Kai Svahn <kai.svahn@nokia.com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307 USA
 *
 */

#ifndef __TWL_H_
#define __TWL_H_

#include <linux/types.h>
#include <linux/input/matrix_keypad.h>

/*
 * Using the twl4030 core we address registers using a pair
 *      { module id, relative register offset }
 * which that core then maps to the relevant
 *      { i2c slave, absolute register address }
 *
 * The module IDs are meaningful only to the twl4030 core code,
 * which uses them as array indices to look up the first register
 * address each module uses within a given i2c slave.
 */

/* Module IDs for similar functionalities found in twl4030/twl6030 */
enum twl_module_ids {
        TWL_MODULE_USB,
        TWL_MODULE_PIH,
        TWL_MODULE_MAIN_CHARGE,
        TWL_MODULE_PM_MASTER,
        TWL_MODULE_PM_RECEIVER,

        TWL_MODULE_RTC,
        TWL_MODULE_PWM,
        TWL_MODULE_LED,
        TWL_MODULE_SECURED_REG,

        TWL_MODULE_LAST,
};

/* Modules only available in twl4030 series */
enum twl4030_module_ids {
        TWL4030_MODULE_AUDIO_VOICE = TWL_MODULE_LAST,
        TWL4030_MODULE_GPIO,
        TWL4030_MODULE_INTBR,
        TWL4030_MODULE_TEST,
        TWL4030_MODULE_KEYPAD,

        TWL4030_MODULE_MADC,
        TWL4030_MODULE_INTERRUPTS,
        TWL4030_MODULE_PRECHARGE,
        TWL4030_MODULE_BACKUP,
        TWL4030_MODULE_INT,

        TWL5031_MODULE_ACCESSORY,
        TWL5031_MODULE_INTERRUPTS,

        TWL4030_MODULE_LAST,
};

/* Modules only available in twl6030 series */
enum twl6030_module_ids {
        TWL6030_MODULE_ID0 = TWL_MODULE_LAST,
        TWL6030_MODULE_ID1,
        TWL6030_MODULE_ID2,
        TWL6030_MODULE_GPADC,
        TWL6030_MODULE_GASGAUGE,

        TWL6030_MODULE_LAST,
};

/* Until the clients has been converted to use TWL_MODULE_LED */
#define TWL4030_MODULE_LED      TWL_MODULE_LED

#define GPIO_INTR_OFFSET        0
#define KEYPAD_INTR_OFFSET      1
#define BCI_INTR_OFFSET         2
#define MADC_INTR_OFFSET        3
#define USB_INTR_OFFSET         4
#define CHARGERFAULT_INTR_OFFSET 5
#define BCI_PRES_INTR_OFFSET    9
#define USB_PRES_INTR_OFFSET    10
#define RTC_INTR_OFFSET         11

/*
 * Offset from TWL6030_IRQ_BASE / pdata->irq_base
 */
#define PWR_INTR_OFFSET         0
#define HOTDIE_INTR_OFFSET      12
#define SMPSLDO_INTR_OFFSET     13
#define BATDETECT_INTR_OFFSET   14
#define SIMDETECT_INTR_OFFSET   15
#define MMCDETECT_INTR_OFFSET   16
#define GASGAUGE_INTR_OFFSET    17
#define USBOTG_INTR_OFFSET      4
#define CHARGER_INTR_OFFSET     2
#define RSV_INTR_OFFSET         0

/* INT register offsets */
#define REG_INT_STS_A                   0x00
#define REG_INT_STS_B                   0x01
#define REG_INT_STS_C                   0x02

#define REG_INT_MSK_LINE_A              0x03
#define REG_INT_MSK_LINE_B              0x04
#define REG_INT_MSK_LINE_C              0x05

#define REG_INT_MSK_STS_A               0x06
#define REG_INT_MSK_STS_B               0x07
#define REG_INT_MSK_STS_C               0x08

/* MASK INT REG GROUP A */
#define TWL6030_PWR_INT_MASK            0x07
#define TWL6030_RTC_INT_MASK            0x18
#define TWL6030_HOTDIE_INT_MASK         0x20
#define TWL6030_SMPSLDOA_INT_MASK       0xC0

/* MASK INT REG GROUP B */
#define TWL6030_SMPSLDOB_INT_MASK       0x01
#define TWL6030_BATDETECT_INT_MASK      0x02
#define TWL6030_SIMDETECT_INT_MASK      0x04
#define TWL6030_MMCDETECT_INT_MASK      0x08
#define TWL6030_GPADC_INT_MASK          0x60
#define TWL6030_GASGAUGE_INT_MASK       0x80

/* MASK INT REG GROUP C */
#define TWL6030_USBOTG_INT_MASK         0x0F
#define TWL6030_CHARGER_CTRL_INT_MASK   0x10
#define TWL6030_CHARGER_FAULT_INT_MASK  0x60

#define TWL6030_MMCCTRL         0xEE
#define VMMC_AUTO_OFF                   (0x1 << 3)
#define SW_FC                           (0x1 << 2)
#define STS_MMC                 0x1

#define TWL6030_CFG_INPUT_PUPD3 0xF2
#define MMC_PU                          (0x1 << 3)
#define MMC_PD                          (0x1 << 2)

#define TWL_SIL_TYPE(rev)               ((rev) & 0x00FFFFFF)
#define TWL_SIL_REV(rev)                ((rev) >> 24)
#define TWL_SIL_5030                    0x09002F
#define TWL5030_REV_1_0                 0x00
#define TWL5030_REV_1_1                 0x10
#define TWL5030_REV_1_2                 0x30

#define TWL4030_CLASS_ID                0x4030
#define TWL6030_CLASS_ID                0x6030
unsigned int twl_rev(void);
#define GET_TWL_REV (twl_rev())
#define TWL_CLASS_IS(class, id)                 \
static inline int twl_class_is_ ##class(void)   \
{                                               \
        return ((id) == (GET_TWL_REV)) ? 1 : 0; \
}

TWL_CLASS_IS(4030, TWL4030_CLASS_ID)
TWL_CLASS_IS(6030, TWL6030_CLASS_ID)

/* Set the regcache bypass for the regmap associated with the nodule */
int twl_set_regcache_bypass(u8 mod_no, bool enable);

/*
 * Read and write several 8-bit registers at once.
 */
int twl_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);

/*
 * Read and write single 8-bit registers
 */
static inline int twl_i2c_write_u8(u8 mod_no, u8 val, u8 reg) {
        return twl_i2c_write(mod_no, &val, reg, 1);
}

static inline int twl_i2c_read_u8(u8 mod_no, u8 *val, u8 reg) {
        return twl_i2c_read(mod_no, val, reg, 1);
}

static inline int twl_i2c_write_u16(u8 mod_no, u16 val, u8 reg) {
        val = cpu_to_le16(val);
        return twl_i2c_write(mod_no, (u8*) &val, reg, 2);
}

static inline int twl_i2c_read_u16(u8 mod_no, u16 *val, u8 reg) {
        int ret;
        ret = twl_i2c_read(mod_no, (u8*) val, reg, 2);
        *val = le16_to_cpu(*val);
        return ret;
}

int twl_get_type(void);
int twl_get_version(void);
int twl_get_hfclk_rate(void);

int twl6030_interrupt_unmask(u8 bit_mask, u8 offset);
int twl6030_interrupt_mask(u8 bit_mask, u8 offset);

/* Card detect Configuration for MMC1 Controller on OMAP4 */
#ifdef CONFIG_TWL4030_CORE
int twl6030_mmc_card_detect_config(void);
#else
static inline int twl6030_mmc_card_detect_config(void)
{
        pr_debug("twl6030_mmc_card_detect_config not supported\n");
        return 0;
}
#endif

/* MMC1 Controller on OMAP4 uses Phoenix irq for Card detect */
#ifdef CONFIG_TWL4030_CORE
int twl6030_mmc_card_detect(struct device *dev, int slot);
#else
static inline int twl6030_mmc_card_detect(struct device *dev, int slot)
{
        pr_debug("Call back twl6030_mmc_card_detect not supported\n");
        return -EIO;
}
#endif
/*----------------------------------------------------------------------*/

/*
 * NOTE:  at up to 1024 registers, this is a big chip.
 *
 * Avoid putting register declarations in this file, instead of into
 * a driver-private file, unless some of the registers in a block
 * need to be shared with other drivers.  One example is blocks that
 * have Secondary IRQ Handler (SIH) registers.
 */

#define TWL4030_SIH_CTRL_EXCLEN_MASK    BIT(0)
#define TWL4030_SIH_CTRL_PENDDIS_MASK   BIT(1)
#define TWL4030_SIH_CTRL_COR_MASK       BIT(2)

/*----------------------------------------------------------------------*/

/*
 * GPIO Block Register offsets (use TWL4030_MODULE_GPIO)
 */

#define REG_GPIODATAIN1                 0x0
#define REG_GPIODATAIN2                 0x1
#define REG_GPIODATAIN3                 0x2
#define REG_GPIODATADIR1                0x3
#define REG_GPIODATADIR2                0x4
#define REG_GPIODATADIR3                0x5
#define REG_GPIODATAOUT1                0x6
#define REG_GPIODATAOUT2                0x7
#define REG_GPIODATAOUT3                0x8
#define REG_CLEARGPIODATAOUT1           0x9
#define REG_CLEARGPIODATAOUT2           0xA
#define REG_CLEARGPIODATAOUT3           0xB
#define REG_SETGPIODATAOUT1             0xC
#define REG_SETGPIODATAOUT2             0xD
#define REG_SETGPIODATAOUT3             0xE
#define REG_GPIO_DEBEN1                 0xF
#define REG_GPIO_DEBEN2                 0x10
#define REG_GPIO_DEBEN3                 0x11
#define REG_GPIO_CTRL                   0x12
#define REG_GPIOPUPDCTR1                0x13
#define REG_GPIOPUPDCTR2                0x14
#define REG_GPIOPUPDCTR3                0x15
#define REG_GPIOPUPDCTR4                0x16
#define REG_GPIOPUPDCTR5                0x17
#define REG_GPIO_ISR1A                  0x19
#define REG_GPIO_ISR2A                  0x1A
#define REG_GPIO_ISR3A                  0x1B
#define REG_GPIO_IMR1A                  0x1C
#define REG_GPIO_IMR2A                  0x1D
#define REG_GPIO_IMR3A                  0x1E
#define REG_GPIO_ISR1B                  0x1F
#define REG_GPIO_ISR2B                  0x20
#define REG_GPIO_ISR3B                  0x21
#define REG_GPIO_IMR1B                  0x22
#define REG_GPIO_IMR2B                  0x23
#define REG_GPIO_IMR3B                  0x24
#define REG_GPIO_EDR1                   0x28
#define REG_GPIO_EDR2                   0x29
#define REG_GPIO_EDR3                   0x2A
#define REG_GPIO_EDR4                   0x2B
#define REG_GPIO_EDR5                   0x2C
#define REG_GPIO_SIH_CTRL               0x2D

/* Up to 18 signals are available as GPIOs, when their
 * pins are not assigned to another use (such as ULPI/USB).
 */
#define TWL4030_GPIO_MAX                18

/*----------------------------------------------------------------------*/

/*Interface Bit Register (INTBR) offsets
 *(Use TWL_4030_MODULE_INTBR)
 */

#define REG_IDCODE_7_0                  0x00
#define REG_IDCODE_15_8                 0x01
#define REG_IDCODE_16_23                0x02
#define REG_IDCODE_31_24                0x03
#define REG_GPPUPDCTR1                  0x0F
#define REG_UNLOCK_TEST_REG             0x12

/*I2C1 and I2C4(SR) SDA/SCL pull-up control bits */

#define I2C_SCL_CTRL_PU                 BIT(0)
#define I2C_SDA_CTRL_PU                 BIT(2)
#define SR_I2C_SCL_CTRL_PU              BIT(4)
#define SR_I2C_SDA_CTRL_PU              BIT(6)

#define TWL_EEPROM_R_UNLOCK             0x49

/*----------------------------------------------------------------------*/

/*
 * Keypad register offsets (use TWL4030_MODULE_KEYPAD)
 * ... SIH/interrupt only
 */

#define TWL4030_KEYPAD_KEYP_ISR1        0x11
#define TWL4030_KEYPAD_KEYP_IMR1        0x12
#define TWL4030_KEYPAD_KEYP_ISR2        0x13
#define TWL4030_KEYPAD_KEYP_IMR2        0x14
#define TWL4030_KEYPAD_KEYP_SIR         0x15    /* test register */
#define TWL4030_KEYPAD_KEYP_EDR         0x16
#define TWL4030_KEYPAD_KEYP_SIH_CTRL    0x17

/*----------------------------------------------------------------------*/

/*
 * Multichannel ADC register offsets (use TWL4030_MODULE_MADC)
 * ... SIH/interrupt only
 */

#define TWL4030_MADC_ISR1               0x61
#define TWL4030_MADC_IMR1               0x62
#define TWL4030_MADC_ISR2               0x63
#define TWL4030_MADC_IMR2               0x64
#define TWL4030_MADC_SIR                0x65    /* test register */
#define TWL4030_MADC_EDR                0x66
#define TWL4030_MADC_SIH_CTRL           0x67

/*----------------------------------------------------------------------*/

/*
 * Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS)
 */

#define TWL4030_INTERRUPTS_BCIISR1A     0x0
#define TWL4030_INTERRUPTS_BCIISR2A     0x1
#define TWL4030_INTERRUPTS_BCIIMR1A     0x2
#define TWL4030_INTERRUPTS_BCIIMR2A     0x3
#define TWL4030_INTERRUPTS_BCIISR1B     0x4
#define TWL4030_INTERRUPTS_BCIISR2B     0x5
#define TWL4030_INTERRUPTS_BCIIMR1B     0x6
#define TWL4030_INTERRUPTS_BCIIMR2B     0x7
#define TWL4030_INTERRUPTS_BCISIR1      0x8     /* test register */
#define TWL4030_INTERRUPTS_BCISIR2      0x9     /* test register */
#define TWL4030_INTERRUPTS_BCIEDR1      0xa
#define TWL4030_INTERRUPTS_BCIEDR2      0xb
#define TWL4030_INTERRUPTS_BCIEDR3      0xc
#define TWL4030_INTERRUPTS_BCISIHCTRL   0xd

/*----------------------------------------------------------------------*/

/*
 * Power Interrupt block register offsets (use TWL4030_MODULE_INT)
 */

#define TWL4030_INT_PWR_ISR1            0x0
#define TWL4030_INT_PWR_IMR1            0x1
#define TWL4030_INT_PWR_ISR2            0x2
#define TWL4030_INT_PWR_IMR2            0x3
#define TWL4030_INT_PWR_SIR             0x4     /* test register */
#define TWL4030_INT_PWR_EDR1            0x5
#define TWL4030_INT_PWR_EDR2            0x6
#define TWL4030_INT_PWR_SIH_CTRL        0x7

/*----------------------------------------------------------------------*/

/*
 * Accessory Interrupts
 */
#define TWL5031_ACIIMR_LSB              0x05
#define TWL5031_ACIIMR_MSB              0x06
#define TWL5031_ACIIDR_LSB              0x07
#define TWL5031_ACIIDR_MSB              0x08
#define TWL5031_ACCISR1                 0x0F
#define TWL5031_ACCIMR1                 0x10
#define TWL5031_ACCISR2                 0x11
#define TWL5031_ACCIMR2                 0x12
#define TWL5031_ACCSIR                  0x13
#define TWL5031_ACCEDR1                 0x14
#define TWL5031_ACCSIHCTRL              0x15

/*----------------------------------------------------------------------*/

/*
 * Battery Charger Controller
 */

#define TWL5031_INTERRUPTS_BCIISR1      0x0
#define TWL5031_INTERRUPTS_BCIIMR1      0x1
#define TWL5031_INTERRUPTS_BCIISR2      0x2
#define TWL5031_INTERRUPTS_BCIIMR2      0x3
#define TWL5031_INTERRUPTS_BCISIR       0x4
#define TWL5031_INTERRUPTS_BCIEDR1      0x5
#define TWL5031_INTERRUPTS_BCIEDR2      0x6
#define TWL5031_INTERRUPTS_BCISIHCTRL   0x7

/*----------------------------------------------------------------------*/

/*
 * PM Master module register offsets (use TWL4030_MODULE_PM_MASTER)
 */

#define TWL4030_PM_MASTER_CFG_P1_TRANSITION     0x00
#define TWL4030_PM_MASTER_CFG_P2_TRANSITION     0x01
#define TWL4030_PM_MASTER_CFG_P3_TRANSITION     0x02
#define TWL4030_PM_MASTER_CFG_P123_TRANSITION   0x03
#define TWL4030_PM_MASTER_STS_BOOT              0x04
#define TWL4030_PM_MASTER_CFG_BOOT              0x05
#define TWL4030_PM_MASTER_SHUNDAN               0x06
#define TWL4030_PM_MASTER_BOOT_BCI              0x07
#define TWL4030_PM_MASTER_CFG_PWRANA1           0x08
#define TWL4030_PM_MASTER_CFG_PWRANA2           0x09
#define TWL4030_PM_MASTER_BACKUP_MISC_STS       0x0b
#define TWL4030_PM_MASTER_BACKUP_MISC_CFG       0x0c
#define TWL4030_PM_MASTER_BACKUP_MISC_TST       0x0d
#define TWL4030_PM_MASTER_PROTECT_KEY           0x0e
#define TWL4030_PM_MASTER_STS_HW_CONDITIONS     0x0f
#define TWL4030_PM_MASTER_P1_SW_EVENTS          0x10
#define TWL4030_PM_MASTER_P2_SW_EVENTS          0x11
#define TWL4030_PM_MASTER_P3_SW_EVENTS          0x12
#define TWL4030_PM_MASTER_STS_P123_STATE        0x13
#define TWL4030_PM_MASTER_PB_CFG                0x14
#define TWL4030_PM_MASTER_PB_WORD_MSB           0x15
#define TWL4030_PM_MASTER_PB_WORD_LSB           0x16
#define TWL4030_PM_MASTER_SEQ_ADD_W2P           0x1c
#define TWL4030_PM_MASTER_SEQ_ADD_P2A           0x1d
#define TWL4030_PM_MASTER_SEQ_ADD_A2W           0x1e
#define TWL4030_PM_MASTER_SEQ_ADD_A2S           0x1f
#define TWL4030_PM_MASTER_SEQ_ADD_S2A12         0x20
#define TWL4030_PM_MASTER_SEQ_ADD_S2A3          0x21
#define TWL4030_PM_MASTER_SEQ_ADD_WARM          0x22
#define TWL4030_PM_MASTER_MEMORY_ADDRESS        0x23
#define TWL4030_PM_MASTER_MEMORY_DATA           0x24

#define TWL4030_PM_MASTER_KEY_CFG1              0xc0
#define TWL4030_PM_MASTER_KEY_CFG2              0x0c

#define TWL4030_PM_MASTER_KEY_TST1              0xe0
#define TWL4030_PM_MASTER_KEY_TST2              0x0e

#define TWL4030_PM_MASTER_GLOBAL_TST            0xb6

/*----------------------------------------------------------------------*/

/* Power bus message definitions */

/* The TWL4030/5030 splits its power-management resources (the various
 * regulators, clock and reset lines) into 3 processor groups - P1, P2 and
 * P3. These groups can then be configured to transition between sleep, wait-on
 * and active states by sending messages to the power bus.  See Section 5.4.2
 * Power Resources of TWL4030 TRM
 */

/* Processor groups */
#define DEV_GRP_NULL            0x0
#define DEV_GRP_P1              0x1     /* P1: all OMAP devices */
#define DEV_GRP_P2              0x2     /* P2: all Modem devices */
#define DEV_GRP_P3              0x4     /* P3: all peripheral devices */

/* Resource groups */
#define RES_GRP_RES             0x0     /* Reserved */
#define RES_GRP_PP              0x1     /* Power providers */
#define RES_GRP_RC              0x2     /* Reset and control */
#define RES_GRP_PP_RC           0x3
#define RES_GRP_PR              0x4     /* Power references */
#define RES_GRP_PP_PR           0x5
#define RES_GRP_RC_PR           0x6
#define RES_GRP_ALL             0x7     /* All resource groups */

#define RES_TYPE2_R0            0x0
#define RES_TYPE2_R1            0x1
#define RES_TYPE2_R2            0x2

#define RES_TYPE_R0             0x0
#define RES_TYPE_ALL            0x7

/* Resource states */
#define RES_STATE_WRST          0xF
#define RES_STATE_ACTIVE        0xE
#define RES_STATE_SLEEP         0x8
#define RES_STATE_OFF           0x0

/* Power resources */

/* Power providers */
#define RES_VAUX1               1
#define RES_VAUX2               2
#define RES_VAUX3               3
#define RES_VAUX4               4
#define RES_VMMC1               5
#define RES_VMMC2               6
#define RES_VPLL1               7
#define RES_VPLL2               8
#define RES_VSIM                9
#define RES_VDAC                10
#define RES_VINTANA1            11
#define RES_VINTANA2            12
#define RES_VINTDIG             13
#define RES_VIO                 14
#define RES_VDD1                15
#define RES_VDD2                16
#define RES_VUSB_1V5            17
#define RES_VUSB_1V8            18
#define RES_VUSB_3V1            19
#define RES_VUSBCP              20
#define RES_REGEN               21
/* Reset and control */
#define RES_NRES_PWRON          22
#define RES_CLKEN               23
#define RES_SYSEN               24
#define RES_HFCLKOUT            25
#define RES_32KCLKOUT           26
#define RES_RESET               27
/* Power Reference */
#define RES_MAIN_REF            28

#define TOTAL_RESOURCES         28
/*
 * Power Bus Message Format ... these can be sent individually by Linux,
 * but are usually part of downloaded scripts that are run when various
 * power events are triggered.
 *
 *  Broadcast Message (16 Bits):
 *    DEV_GRP[15:13] MT[12]  RES_GRP[11:9]  RES_TYPE2[8:7] RES_TYPE[6:4]
 *    RES_STATE[3:0]
 *
 *  Singular Message (16 Bits):
 *    DEV_GRP[15:13] MT[12]  RES_ID[11:4]  RES_STATE[3:0]
 */

#define MSG_BROADCAST(devgrp, grp, type, type2, state) \
        ( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \
        | (type) << 4 | (state))

#define MSG_SINGULAR(devgrp, id, state) \
        ((devgrp) << 13 | 0 << 12 | (id) << 4 | (state))

#define MSG_BROADCAST_ALL(devgrp, state) \
        ((devgrp) << 5 | (state))

#define MSG_BROADCAST_REF MSG_BROADCAST_ALL
#define MSG_BROADCAST_PROV MSG_BROADCAST_ALL
#define MSG_BROADCAST__CLK_RST MSG_BROADCAST_ALL
/*----------------------------------------------------------------------*/

struct twl4030_clock_init_data {
        bool ck32k_lowpwr_enable;
};

struct twl4030_bci_platform_data {
        int *battery_tmp_tbl;
        unsigned int tblsize;
        int     bb_uvolt;       /* voltage to charge backup battery */
        int     bb_uamp;        /* current for backup battery charging */
};

/* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */
struct twl4030_gpio_platform_data {
        /* package the two LED signals as output-only GPIOs? */
        bool            use_leds;

        /* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */
        u8              mmc_cd;

        /* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */
        u32             debounce;

        /* For gpio-N, bit (1 << N) in "pullups" is set if that pullup
         * should be enabled.  Else, if that bit is set in "pulldowns",
         * that pulldown is enabled.  Don't waste power by letting any
         * digital inputs float...
         */
        u32             pullups;
        u32             pulldowns;

        int             (*setup)(struct device *dev,
                                unsigned gpio, unsigned ngpio);
        int             (*teardown)(struct device *dev,
                                unsigned gpio, unsigned ngpio);
};

struct twl4030_madc_platform_data {
        int             irq_line;
};

/* Boards have unique mappings of {row, col} --> keycode.
 * Column and row are 8 bits each, but range only from 0..7.
 * a PERSISTENT_KEY is "always on" and never reported.
 */
#define PERSISTENT_KEY(r, c)    KEY((r), (c), KEY_RESERVED)

struct twl4030_keypad_data {
        const struct matrix_keymap_data *keymap_data;
        unsigned rows;
        unsigned cols;
        bool rep;
};

enum twl4030_usb_mode {
        T2_USB_MODE_ULPI = 1,
        T2_USB_MODE_CEA2011_3PIN = 2,
};

struct twl4030_usb_data {
        enum twl4030_usb_mode   usb_mode;
        unsigned long           features;

        int             (*phy_init)(struct device *dev);
        int             (*phy_exit)(struct device *dev);
        /* Power on/off the PHY */
        int             (*phy_power)(struct device *dev, int iD, int on);
        /* enable/disable  phy clocks */
        int             (*phy_set_clock)(struct device *dev, int on);
        /* suspend/resume of phy */
        int             (*phy_suspend)(struct device *dev, int suspend);
};

struct twl4030_ins {
        u16 pmb_message;
        u8 delay;
};

struct twl4030_script {
        struct twl4030_ins *script;
        unsigned size;
        u8 flags;
#define TWL4030_WRST_SCRIPT     (1<<0)
#define TWL4030_WAKEUP12_SCRIPT (1<<1)
#define TWL4030_WAKEUP3_SCRIPT  (1<<2)
#define TWL4030_SLEEP_SCRIPT    (1<<3)
};

struct twl4030_resconfig {
        u8 resource;
        u8 devgroup;    /* Processor group that Power resource belongs to */
        u8 type;        /* Power resource addressed, 6 / broadcast message */
        u8 type2;       /* Power resource addressed, 3 / broadcast message */
        u8 remap_off;   /* off state remapping */
        u8 remap_sleep; /* sleep state remapping */
};

struct twl4030_power_data {
        struct twl4030_script **scripts;
        unsigned num;
        struct twl4030_resconfig *resource_config;
        struct twl4030_resconfig *board_config;
#define TWL4030_RESCONFIG_UNDEF ((u8)-1)
        bool use_poweroff;      /* Board is wired for TWL poweroff */
        bool ac_charger_quirk;  /* Disable AC charger on board */
};

extern int twl4030_remove_script(u8 flags);
extern void twl4030_power_off(void);

struct twl4030_codec_data {
        unsigned int digimic_delay; /* in ms */
        unsigned int ramp_delay_value;
        unsigned int offset_cncl_path;
        unsigned int hs_extmute:1;
        int hs_extmute_gpio;
};

struct twl4030_vibra_data {
        unsigned int    coexist;
};

struct twl4030_audio_data {
        unsigned int    audio_mclk;
        struct twl4030_codec_data *codec;
        struct twl4030_vibra_data *vibra;

        /* twl6040 */
        int audpwron_gpio;      /* audio power-on gpio */
        int naudint_irq;        /* audio interrupt */
        unsigned int irq_base;
};

struct twl4030_platform_data {
        struct twl4030_clock_init_data          *clock;
        struct twl4030_bci_platform_data        *bci;
        struct twl4030_gpio_platform_data       *gpio;
        struct twl4030_madc_platform_data       *madc;
        struct twl4030_keypad_data              *keypad;
        struct twl4030_usb_data                 *usb;
        struct twl4030_power_data               *power;
        struct twl4030_audio_data               *audio;

        /* Common LDO regulators for TWL4030/TWL6030 */
        struct regulator_init_data              *vdac;
        struct regulator_init_data              *vaux1;
        struct regulator_init_data              *vaux2;
        struct regulator_init_data              *vaux3;
        struct regulator_init_data              *vdd1;
        struct regulator_init_data              *vdd2;
        struct regulator_init_data              *vdd3;
        /* TWL4030 LDO regulators */
        struct regulator_init_data              *vpll1;
        struct regulator_init_data              *vpll2;
        struct regulator_init_data              *vmmc1;
        struct regulator_init_data              *vmmc2;
        struct regulator_init_data              *vsim;
        struct regulator_init_data              *vaux4;
        struct regulator_init_data              *vio;
        struct regulator_init_data              *vintana1;
        struct regulator_init_data              *vintana2;
        struct regulator_init_data              *vintdig;
        /* TWL6030 LDO regulators */
        struct regulator_init_data              *vmmc;
        struct regulator_init_data              *vpp;
        struct regulator_init_data              *vusim;
        struct regulator_init_data              *vana;
        struct regulator_init_data              *vcxio;
        struct regulator_init_data              *vusb;
        struct regulator_init_data              *clk32kg;
        struct regulator_init_data              *v1v8;
        struct regulator_init_data              *v2v1;
        /* TWL6032 LDO regulators */
        struct regulator_init_data              *ldo1;
        struct regulator_init_data              *ldo2;
        struct regulator_init_data              *ldo3;
        struct regulator_init_data              *ldo4;
        struct regulator_init_data              *ldo5;
        struct regulator_init_data              *ldo6;
        struct regulator_init_data              *ldo7;
        struct regulator_init_data              *ldoln;
        struct regulator_init_data              *ldousb;
        /* TWL6032 DCDC regulators */
        struct regulator_init_data              *smps3;
        struct regulator_init_data              *smps4;
        struct regulator_init_data              *vio6025;
};

struct twl_regulator_driver_data {
        int             (*set_voltage)(void *data, int target_uV);
        int             (*get_voltage)(void *data);
        void            *data;
        unsigned long   features;
};
/* chip-specific feature flags, for twl_regulator_driver_data.features */
#define TWL4030_VAUX2           BIT(0)  /* pre-5030 voltage ranges */
#define TPS_SUBSET              BIT(1)  /* tps659[23]0 have fewer LDOs */
#define TWL5031                 BIT(2)  /* twl5031 has different registers */
#define TWL6030_CLASS           BIT(3)  /* TWL6030 class */
#define TWL6032_SUBCLASS        BIT(4)  /* TWL6032 has changed registers */
#define TWL4030_ALLOW_UNSUPPORTED BIT(5) /* Some voltages are possible
                                          * but not officially supported.
                                          * This flag is necessary to
                                          * enable them.
                                          */

/*----------------------------------------------------------------------*/

int twl4030_sih_setup(struct device *dev, int module, int irq_base);

/* Offsets to Power Registers */
#define TWL4030_VDAC_DEV_GRP            0x3B
#define TWL4030_VDAC_DEDICATED          0x3E
#define TWL4030_VAUX1_DEV_GRP           0x17
#define TWL4030_VAUX1_DEDICATED         0x1A
#define TWL4030_VAUX2_DEV_GRP           0x1B
#define TWL4030_VAUX2_DEDICATED         0x1E
#define TWL4030_VAUX3_DEV_GRP           0x1F
#define TWL4030_VAUX3_DEDICATED         0x22

static inline int twl4030charger_usb_en(int enable) { return 0; }

/*----------------------------------------------------------------------*/

/* Linux-specific regulator identifiers ... for now, we only support
 * the LDOs, and leave the three buck converters alone.  VDD1 and VDD2
 * need to tie into hardware based voltage scaling (cpufreq etc), while
 * VIO is generally fixed.
 */

/* TWL4030 SMPS/LDO's */
/* EXTERNAL dc-to-dc buck converters */
#define TWL4030_REG_VDD1        0
#define TWL4030_REG_VDD2        1
#define TWL4030_REG_VIO         2

/* EXTERNAL LDOs */
#define TWL4030_REG_VDAC        3
#define TWL4030_REG_VPLL1       4
#define TWL4030_REG_VPLL2       5       /* not on all chips */
#define TWL4030_REG_VMMC1       6
#define TWL4030_REG_VMMC2       7       /* not on all chips */
#define TWL4030_REG_VSIM        8       /* not on all chips */
#define TWL4030_REG_VAUX1       9       /* not on all chips */
#define TWL4030_REG_VAUX2_4030  10      /* (twl4030-specific) */
#define TWL4030_REG_VAUX2       11      /* (twl5030 and newer) */
#define TWL4030_REG_VAUX3       12      /* not on all chips */
#define TWL4030_REG_VAUX4       13      /* not on all chips */

/* INTERNAL LDOs */
#define TWL4030_REG_VINTANA1    14
#define TWL4030_REG_VINTANA2    15
#define TWL4030_REG_VINTDIG     16
#define TWL4030_REG_VUSB1V5     17
#define TWL4030_REG_VUSB1V8     18
#define TWL4030_REG_VUSB3V1     19

/* TWL6030 SMPS/LDO's */
/* EXTERNAL dc-to-dc buck convertor controllable via SR */
#define TWL6030_REG_VDD1        30
#define TWL6030_REG_VDD2        31
#define TWL6030_REG_VDD3        32

/* Non SR compliant dc-to-dc buck convertors */
#define TWL6030_REG_VMEM        33
#define TWL6030_REG_V2V1        34
#define TWL6030_REG_V1V29       35
#define TWL6030_REG_V1V8        36

/* EXTERNAL LDOs */
#define TWL6030_REG_VAUX1_6030  37
#define TWL6030_REG_VAUX2_6030  38
#define TWL6030_REG_VAUX3_6030  39
#define TWL6030_REG_VMMC        40
#define TWL6030_REG_VPP         41
#define TWL6030_REG_VUSIM       42
#define TWL6030_REG_VANA        43
#define TWL6030_REG_VCXIO       44
#define TWL6030_REG_VDAC        45
#define TWL6030_REG_VUSB        46

/* INTERNAL LDOs */
#define TWL6030_REG_VRTC        47
#define TWL6030_REG_CLK32KG     48

/* LDOs on 6025 have different names */
#define TWL6032_REG_LDO2        49
#define TWL6032_REG_LDO4        50
#define TWL6032_REG_LDO3        51
#define TWL6032_REG_LDO5        52
#define TWL6032_REG_LDO1        53
#define TWL6032_REG_LDO7        54
#define TWL6032_REG_LDO6        55
#define TWL6032_REG_LDOLN       56
#define TWL6032_REG_LDOUSB      57

/* 6025 DCDC supplies */
#define TWL6032_REG_SMPS3       58
#define TWL6032_REG_SMPS4       59
#define TWL6032_REG_VIO         60


#endif /* End of __TWL4030_H */