LXR linux/drivers/staging/rtl8723au/include/Hal8723PwrSeq.h

   1#ifndef __HAL8723PWRSEQ_H__
   2#define __HAL8723PWRSEQ_H__
   3/*
   4        Check document WM-20110607-Paul-RTL8723A_Power_Architecture-R02.vsd
   5        There are 6 HW Power States:
   6        0: POFF--Power Off
   7        1: PDN--Power Down
   8        2: CARDEMU--Card Emulation
   9        3: ACT--Active Mode
  10        4: LPS--Low Power State
  11        5: SUS--Suspend
  12
  13        The transision from different states are defined below
  14        TRANS_CARDEMU_TO_ACT
  15        TRANS_ACT_TO_CARDEMU
  16        TRANS_CARDEMU_TO_SUS
  17        TRANS_SUS_TO_CARDEMU
  18        TRANS_CARDEMU_TO_PDN
  19        TRANS_ACT_TO_LPS
  20        TRANS_LPS_TO_ACT
  21
  22        TRANS_END
  23*/
  24#include "HalPwrSeqCmd.h"
  25#include "rtl8723a_spec.h"
  26
  27#define RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS     15
  28#define RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS     15
  29#define RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS     15
  30#define RTL8723A_TRANS_SUS_TO_CARDEMU_STEPS     15
  31#define RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS     15
  32#define RTL8723A_TRANS_PDN_TO_CARDEMU_STEPS     15
  33#define RTL8723A_TRANS_ACT_TO_LPS_STEPS 15
  34#define RTL8723A_TRANS_LPS_TO_ACT_STEPS 15
  35#define RTL8723A_TRANS_END_STEPS        1
  36
  37
  38/* format
  39 * { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },  comments here
  40 */
  41#define RTL8723A_TRANS_CARDEMU_TO_ACT                                                                                                           \
  42        {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/ \
  43        {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/    \
  44        {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/   \
  45        {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), 0}, /*0x00[5] = 1b'0 release analog Ips to digital , 1:isolation*/   \
  46        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(2), 0},/* disable SW LPS 0x04[10]= 0*/        \
  47        {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)},/* wait till 0x04[17] = 1    power ready*/      \
  48        {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},/* release WLON reset  0x04[16]= 1*/ \
  49        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},/* disable HWPDN 0x04[15]= 0*/ \
  50        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4)|BIT(3)), 0},/* disable WL suspend*/       \
  51        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)},/* polling until return 0*/       \
  52        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0},/**/ \
  53        {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 1},/*0x4C[23] = 0x4E[7] = 1, switch DPDT_SEL_P output from WL BB */\
  54
  55#define RTL8723A_TRANS_ACT_TO_CARDEMU                                                                                                   \
  56        {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/    \
  57        {0x004E, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},/*0x4C[23] = 0x4E[7] = 0, switch DPDT_SEL_P output from register 0x65[2] */\
  58        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, /*0x04[9] = 1 turn off MAC by HW state machine*/ \
  59        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \
  60        {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)}, /*0x00[5] = 1b'1 analog Ips to digital , 1:isolation*/   \
  61        {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/   \
  62
  63
  64#define RTL8723A_TRANS_CARDEMU_TO_SUS                                                                                                   \
  65        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, /*0x04[12:11] = 2b'01 enable WL suspend*/
  66
  67#define RTL8723A_TRANS_SUS_TO_CARDEMU                                                                                                   \
  68        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, /*clear suspend enable and power down enable*/       \
  69        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, /*0x04[12:11] = 2b'01enable WL suspend*/
  70
  71#define RTL8723A_TRANS_CARDEMU_TO_CARDDIS                                                                                                       \
  72        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, /*0x04[12:11] = 2b'01 enable WL suspend*/ \
  73        {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/
  74
  75#define RTL8723A_TRANS_CARDDIS_TO_CARDEMU                                                                                                       \
  76        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, /*clear suspend enable and power down enable*/       \
  77        {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/   \
  78        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, /*0x04[12:11] = 2b'01enable WL suspend*/
  79
  80#define RTL8723A_TRANS_CARDEMU_TO_PDN                                                                                           \
  81        {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/   \
  82        {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0},/* 0x04[16] = 0*/\
  83        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7)},/* 0x04[15] = 1*/
  84
  85#define RTL8723A_TRANS_PDN_TO_CARDEMU                                                                                           \
  86        {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0},/* 0x04[15] = 0*/
  87
  88#define RTL8723A_TRANS_ACT_TO_LPS                                                                                                               \
  89        {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/  \
  90        {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/        \
  91        {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/        \
  92        {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/        \
  93        {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/        \
  94        {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0},/*CCK and OFDM are disabled, and clock are gated*/     \
  95        {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/ \
  96        {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*Whole BB is reset*/  \
  97        {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/     \
  98        {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0},/*check if removed later*/     \
  99        {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)},/*Respond TxOK to scheduler*/
 100
 101#define RTL8723A_TRANS_LPS_TO_ACT                                                                                                                       \
 102        {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
 103        {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
 104        {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, /*.   0x08[4] = 0              switch TSF to 40M*/\
 105        {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(7), 0}, /*Polling 0x109[7]= 0  TSF in 40M*/\
 106        {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6)|BIT(7), 0}, /*.    0x29[7:6] = 2b'00        enable BB clock*/\
 107        {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, /*.      0x101[1] = 1*/\
 108        {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, /*.  0x100[7:0] = 0xFF        enable WMAC TRX*/\
 109        {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1)|BIT(0), BIT(1)|BIT(0)}, /*.        0x02[1:0] = 2b'11        enable BB macro*/\
 110        {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, /*.     0x522 = 0*/
 111
 112#define RTL8723A_TRANS_END                                                                                                                      \
 113        {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, PWR_CMD_END, 0, 0},
 114
 115
 116extern struct wlan_pwr_cfg rtl8723AU_power_on_flow[RTL8723A_TRANS_CARDEMU_TO_ACT_STEPS+RTL8723A_TRANS_END_STEPS];
 117extern struct wlan_pwr_cfg rtl8723AU_radio_off_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_END_STEPS];
 118extern struct wlan_pwr_cfg rtl8723AU_card_disable_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS];
 119extern struct wlan_pwr_cfg rtl8723AU_card_enable_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS];
 120extern struct wlan_pwr_cfg rtl8723AU_suspend_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723A_TRANS_END_STEPS];
 121extern struct wlan_pwr_cfg rtl8723AU_resume_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8723A_TRANS_END_STEPS];
 122extern struct wlan_pwr_cfg rtl8723AU_hwpdn_flow[RTL8723A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8723A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8723A_TRANS_END_STEPS];
 123extern struct wlan_pwr_cfg rtl8723AU_enter_lps_flow[RTL8723A_TRANS_ACT_TO_LPS_STEPS+RTL8723A_TRANS_END_STEPS];
 124extern struct wlan_pwr_cfg rtl8723AU_leave_lps_flow[RTL8723A_TRANS_LPS_TO_ACT_STEPS+RTL8723A_TRANS_END_STEPS];
 125
 126#endif
 127