linux/drivers/usb/serial/ti_usb_3410_5052.c
<<
>>
Prefs
   1/* vi: ts=8 sw=8
   2 *
   3 * TI 3410/5052 USB Serial Driver
   4 *
   5 * Copyright (C) 2004 Texas Instruments
   6 *
   7 * This driver is based on the Linux io_ti driver, which is
   8 *   Copyright (C) 2000-2002 Inside Out Networks
   9 *   Copyright (C) 2001-2002 Greg Kroah-Hartman
  10 *
  11 * This program is free software; you can redistribute it and/or modify
  12 * it under the terms of the GNU General Public License as published by
  13 * the Free Software Foundation; either version 2 of the License, or
  14 * (at your option) any later version.
  15 *
  16 * For questions or problems with this driver, contact Texas Instruments
  17 * technical support, or Al Borchers <alborchers@steinerpoint.com>, or
  18 * Peter Berger <pberger@brimson.com>.
  19 */
  20
  21#include <linux/kernel.h>
  22#include <linux/errno.h>
  23#include <linux/firmware.h>
  24#include <linux/slab.h>
  25#include <linux/tty.h>
  26#include <linux/tty_driver.h>
  27#include <linux/tty_flip.h>
  28#include <linux/module.h>
  29#include <linux/spinlock.h>
  30#include <linux/ioctl.h>
  31#include <linux/serial.h>
  32#include <linux/kfifo.h>
  33#include <linux/mutex.h>
  34#include <linux/uaccess.h>
  35#include <linux/usb.h>
  36#include <linux/usb/serial.h>
  37
  38#include "ti_usb_3410_5052.h"
  39
  40/* Defines */
  41
  42#define TI_DRIVER_AUTHOR        "Al Borchers <alborchers@steinerpoint.com>"
  43#define TI_DRIVER_DESC          "TI USB 3410/5052 Serial Driver"
  44
  45#define TI_FIRMWARE_BUF_SIZE    16284
  46
  47#define TI_TRANSFER_TIMEOUT     2
  48
  49#define TI_DEFAULT_CLOSING_WAIT 4000            /* in .01 secs */
  50
  51/* supported setserial flags */
  52#define TI_SET_SERIAL_FLAGS     0
  53
  54/* read urb states */
  55#define TI_READ_URB_RUNNING     0
  56#define TI_READ_URB_STOPPING    1
  57#define TI_READ_URB_STOPPED     2
  58
  59#define TI_EXTRA_VID_PID_COUNT  5
  60
  61
  62/* Structures */
  63
  64struct ti_port {
  65        int                     tp_is_open;
  66        __u8                    tp_msr;
  67        __u8                    tp_shadow_mcr;
  68        __u8                    tp_uart_mode;   /* 232 or 485 modes */
  69        unsigned int            tp_uart_base_addr;
  70        int                     tp_flags;
  71        struct ti_device        *tp_tdev;
  72        struct usb_serial_port  *tp_port;
  73        spinlock_t              tp_lock;
  74        int                     tp_read_urb_state;
  75        int                     tp_write_urb_in_use;
  76};
  77
  78struct ti_device {
  79        struct mutex            td_open_close_lock;
  80        int                     td_open_port_count;
  81        struct usb_serial       *td_serial;
  82        int                     td_is_3410;
  83        int                     td_urb_error;
  84};
  85
  86
  87/* Function Declarations */
  88
  89static int ti_startup(struct usb_serial *serial);
  90static void ti_release(struct usb_serial *serial);
  91static int ti_port_probe(struct usb_serial_port *port);
  92static int ti_port_remove(struct usb_serial_port *port);
  93static int ti_open(struct tty_struct *tty, struct usb_serial_port *port);
  94static void ti_close(struct usb_serial_port *port);
  95static int ti_write(struct tty_struct *tty, struct usb_serial_port *port,
  96                const unsigned char *data, int count);
  97static int ti_write_room(struct tty_struct *tty);
  98static int ti_chars_in_buffer(struct tty_struct *tty);
  99static bool ti_tx_empty(struct usb_serial_port *port);
 100static void ti_throttle(struct tty_struct *tty);
 101static void ti_unthrottle(struct tty_struct *tty);
 102static int ti_ioctl(struct tty_struct *tty,
 103                unsigned int cmd, unsigned long arg);
 104static void ti_set_termios(struct tty_struct *tty,
 105                struct usb_serial_port *port, struct ktermios *old_termios);
 106static int ti_tiocmget(struct tty_struct *tty);
 107static int ti_tiocmset(struct tty_struct *tty,
 108                unsigned int set, unsigned int clear);
 109static void ti_break(struct tty_struct *tty, int break_state);
 110static void ti_interrupt_callback(struct urb *urb);
 111static void ti_bulk_in_callback(struct urb *urb);
 112static void ti_bulk_out_callback(struct urb *urb);
 113
 114static void ti_recv(struct usb_serial_port *port, unsigned char *data,
 115                int length);
 116static void ti_send(struct ti_port *tport);
 117static int ti_set_mcr(struct ti_port *tport, unsigned int mcr);
 118static int ti_get_lsr(struct ti_port *tport, u8 *lsr);
 119static int ti_get_serial_info(struct ti_port *tport,
 120        struct serial_struct __user *ret_arg);
 121static int ti_set_serial_info(struct tty_struct *tty, struct ti_port *tport,
 122        struct serial_struct __user *new_arg);
 123static void ti_handle_new_msr(struct ti_port *tport, __u8 msr);
 124
 125static void ti_stop_read(struct ti_port *tport, struct tty_struct *tty);
 126static int ti_restart_read(struct ti_port *tport, struct tty_struct *tty);
 127
 128static int ti_command_out_sync(struct ti_device *tdev, __u8 command,
 129        __u16 moduleid, __u16 value, __u8 *data, int size);
 130static int ti_command_in_sync(struct ti_device *tdev, __u8 command,
 131        __u16 moduleid, __u16 value, __u8 *data, int size);
 132
 133static int ti_write_byte(struct usb_serial_port *port, struct ti_device *tdev,
 134                         unsigned long addr, __u8 mask, __u8 byte);
 135
 136static int ti_download_firmware(struct ti_device *tdev);
 137
 138
 139/* Data */
 140
 141/* module parameters */
 142static int closing_wait = TI_DEFAULT_CLOSING_WAIT;
 143
 144/* supported devices */
 145static const struct usb_device_id ti_id_table_3410[] = {
 146        { USB_DEVICE(TI_VENDOR_ID, TI_3410_PRODUCT_ID) },
 147        { USB_DEVICE(TI_VENDOR_ID, TI_3410_EZ430_ID) },
 148        { USB_DEVICE(MTS_VENDOR_ID, MTS_GSM_NO_FW_PRODUCT_ID) },
 149        { USB_DEVICE(MTS_VENDOR_ID, MTS_CDMA_NO_FW_PRODUCT_ID) },
 150        { USB_DEVICE(MTS_VENDOR_ID, MTS_CDMA_PRODUCT_ID) },
 151        { USB_DEVICE(MTS_VENDOR_ID, MTS_GSM_PRODUCT_ID) },
 152        { USB_DEVICE(MTS_VENDOR_ID, MTS_EDGE_PRODUCT_ID) },
 153        { USB_DEVICE(MTS_VENDOR_ID, MTS_MT9234MU_PRODUCT_ID) },
 154        { USB_DEVICE(MTS_VENDOR_ID, MTS_MT9234ZBA_PRODUCT_ID) },
 155        { USB_DEVICE(MTS_VENDOR_ID, MTS_MT9234ZBAOLD_PRODUCT_ID) },
 156        { USB_DEVICE(IBM_VENDOR_ID, IBM_4543_PRODUCT_ID) },
 157        { USB_DEVICE(IBM_VENDOR_ID, IBM_454B_PRODUCT_ID) },
 158        { USB_DEVICE(IBM_VENDOR_ID, IBM_454C_PRODUCT_ID) },
 159        { USB_DEVICE(ABBOTT_VENDOR_ID, ABBOTT_STEREO_PLUG_ID) },
 160        { USB_DEVICE(ABBOTT_VENDOR_ID, ABBOTT_STRIP_PORT_ID) },
 161        { USB_DEVICE(TI_VENDOR_ID, FRI2_PRODUCT_ID) },
 162        { USB_DEVICE(HONEYWELL_VENDOR_ID, HONEYWELL_HGI80_PRODUCT_ID) },
 163        { }     /* terminator */
 164};
 165
 166static const struct usb_device_id ti_id_table_5052[] = {
 167        { USB_DEVICE(TI_VENDOR_ID, TI_5052_BOOT_PRODUCT_ID) },
 168        { USB_DEVICE(TI_VENDOR_ID, TI_5152_BOOT_PRODUCT_ID) },
 169        { USB_DEVICE(TI_VENDOR_ID, TI_5052_EEPROM_PRODUCT_ID) },
 170        { USB_DEVICE(TI_VENDOR_ID, TI_5052_FIRMWARE_PRODUCT_ID) },
 171        { }     /* terminator */
 172};
 173
 174static const struct usb_device_id ti_id_table_combined[] = {
 175        { USB_DEVICE(TI_VENDOR_ID, TI_3410_PRODUCT_ID) },
 176        { USB_DEVICE(TI_VENDOR_ID, TI_3410_EZ430_ID) },
 177        { USB_DEVICE(MTS_VENDOR_ID, MTS_GSM_NO_FW_PRODUCT_ID) },
 178        { USB_DEVICE(MTS_VENDOR_ID, MTS_CDMA_NO_FW_PRODUCT_ID) },
 179        { USB_DEVICE(MTS_VENDOR_ID, MTS_CDMA_PRODUCT_ID) },
 180        { USB_DEVICE(MTS_VENDOR_ID, MTS_GSM_PRODUCT_ID) },
 181        { USB_DEVICE(MTS_VENDOR_ID, MTS_EDGE_PRODUCT_ID) },
 182        { USB_DEVICE(MTS_VENDOR_ID, MTS_MT9234MU_PRODUCT_ID) },
 183        { USB_DEVICE(MTS_VENDOR_ID, MTS_MT9234ZBA_PRODUCT_ID) },
 184        { USB_DEVICE(MTS_VENDOR_ID, MTS_MT9234ZBAOLD_PRODUCT_ID) },
 185        { USB_DEVICE(TI_VENDOR_ID, TI_5052_BOOT_PRODUCT_ID) },
 186        { USB_DEVICE(TI_VENDOR_ID, TI_5152_BOOT_PRODUCT_ID) },
 187        { USB_DEVICE(TI_VENDOR_ID, TI_5052_EEPROM_PRODUCT_ID) },
 188        { USB_DEVICE(TI_VENDOR_ID, TI_5052_FIRMWARE_PRODUCT_ID) },
 189        { USB_DEVICE(IBM_VENDOR_ID, IBM_4543_PRODUCT_ID) },
 190        { USB_DEVICE(IBM_VENDOR_ID, IBM_454B_PRODUCT_ID) },
 191        { USB_DEVICE(IBM_VENDOR_ID, IBM_454C_PRODUCT_ID) },
 192        { USB_DEVICE(ABBOTT_VENDOR_ID, ABBOTT_PRODUCT_ID) },
 193        { USB_DEVICE(ABBOTT_VENDOR_ID, ABBOTT_STRIP_PORT_ID) },
 194        { USB_DEVICE(TI_VENDOR_ID, FRI2_PRODUCT_ID) },
 195        { USB_DEVICE(HONEYWELL_VENDOR_ID, HONEYWELL_HGI80_PRODUCT_ID) },
 196        { }     /* terminator */
 197};
 198
 199static struct usb_serial_driver ti_1port_device = {
 200        .driver = {
 201                .owner          = THIS_MODULE,
 202                .name           = "ti_usb_3410_5052_1",
 203        },
 204        .description            = "TI USB 3410 1 port adapter",
 205        .id_table               = ti_id_table_3410,
 206        .num_ports              = 1,
 207        .attach                 = ti_startup,
 208        .release                = ti_release,
 209        .port_probe             = ti_port_probe,
 210        .port_remove            = ti_port_remove,
 211        .open                   = ti_open,
 212        .close                  = ti_close,
 213        .write                  = ti_write,
 214        .write_room             = ti_write_room,
 215        .chars_in_buffer        = ti_chars_in_buffer,
 216        .tx_empty               = ti_tx_empty,
 217        .throttle               = ti_throttle,
 218        .unthrottle             = ti_unthrottle,
 219        .ioctl                  = ti_ioctl,
 220        .set_termios            = ti_set_termios,
 221        .tiocmget               = ti_tiocmget,
 222        .tiocmset               = ti_tiocmset,
 223        .tiocmiwait             = usb_serial_generic_tiocmiwait,
 224        .get_icount             = usb_serial_generic_get_icount,
 225        .break_ctl              = ti_break,
 226        .read_int_callback      = ti_interrupt_callback,
 227        .read_bulk_callback     = ti_bulk_in_callback,
 228        .write_bulk_callback    = ti_bulk_out_callback,
 229};
 230
 231static struct usb_serial_driver ti_2port_device = {
 232        .driver = {
 233                .owner          = THIS_MODULE,
 234                .name           = "ti_usb_3410_5052_2",
 235        },
 236        .description            = "TI USB 5052 2 port adapter",
 237        .id_table               = ti_id_table_5052,
 238        .num_ports              = 2,
 239        .attach                 = ti_startup,
 240        .release                = ti_release,
 241        .port_probe             = ti_port_probe,
 242        .port_remove            = ti_port_remove,
 243        .open                   = ti_open,
 244        .close                  = ti_close,
 245        .write                  = ti_write,
 246        .write_room             = ti_write_room,
 247        .chars_in_buffer        = ti_chars_in_buffer,
 248        .tx_empty               = ti_tx_empty,
 249        .throttle               = ti_throttle,
 250        .unthrottle             = ti_unthrottle,
 251        .ioctl                  = ti_ioctl,
 252        .set_termios            = ti_set_termios,
 253        .tiocmget               = ti_tiocmget,
 254        .tiocmset               = ti_tiocmset,
 255        .tiocmiwait             = usb_serial_generic_tiocmiwait,
 256        .get_icount             = usb_serial_generic_get_icount,
 257        .break_ctl              = ti_break,
 258        .read_int_callback      = ti_interrupt_callback,
 259        .read_bulk_callback     = ti_bulk_in_callback,
 260        .write_bulk_callback    = ti_bulk_out_callback,
 261};
 262
 263static struct usb_serial_driver * const serial_drivers[] = {
 264        &ti_1port_device, &ti_2port_device, NULL
 265};
 266
 267/* Module */
 268
 269MODULE_AUTHOR(TI_DRIVER_AUTHOR);
 270MODULE_DESCRIPTION(TI_DRIVER_DESC);
 271MODULE_LICENSE("GPL");
 272
 273MODULE_FIRMWARE("ti_3410.fw");
 274MODULE_FIRMWARE("ti_5052.fw");
 275MODULE_FIRMWARE("mts_cdma.fw");
 276MODULE_FIRMWARE("mts_gsm.fw");
 277MODULE_FIRMWARE("mts_edge.fw");
 278MODULE_FIRMWARE("mts_mt9234mu.fw");
 279MODULE_FIRMWARE("mts_mt9234zba.fw");
 280
 281module_param(closing_wait, int, S_IRUGO | S_IWUSR);
 282MODULE_PARM_DESC(closing_wait,
 283    "Maximum wait for data to drain in close, in .01 secs, default is 4000");
 284
 285MODULE_DEVICE_TABLE(usb, ti_id_table_combined);
 286
 287module_usb_serial_driver(serial_drivers, ti_id_table_combined);
 288
 289/* Functions */
 290
 291static int ti_startup(struct usb_serial *serial)
 292{
 293        struct ti_device *tdev;
 294        struct usb_device *dev = serial->dev;
 295        int status;
 296
 297        dev_dbg(&dev->dev,
 298                "%s - product 0x%4X, num configurations %d, configuration value %d\n",
 299                __func__, le16_to_cpu(dev->descriptor.idProduct),
 300                dev->descriptor.bNumConfigurations,
 301                dev->actconfig->desc.bConfigurationValue);
 302
 303        /* create device structure */
 304        tdev = kzalloc(sizeof(struct ti_device), GFP_KERNEL);
 305        if (!tdev)
 306                return -ENOMEM;
 307
 308        mutex_init(&tdev->td_open_close_lock);
 309        tdev->td_serial = serial;
 310        usb_set_serial_data(serial, tdev);
 311
 312        /* determine device type */
 313        if (serial->type == &ti_1port_device)
 314                tdev->td_is_3410 = 1;
 315        dev_dbg(&dev->dev, "%s - device type is %s\n", __func__,
 316                tdev->td_is_3410 ? "3410" : "5052");
 317
 318        /* if we have only 1 configuration, download firmware */
 319        if (dev->descriptor.bNumConfigurations == 1) {
 320                status = ti_download_firmware(tdev);
 321
 322                if (status != 0)
 323                        goto free_tdev;
 324
 325                /* 3410 must be reset, 5052 resets itself */
 326                if (tdev->td_is_3410) {
 327                        msleep_interruptible(100);
 328                        usb_reset_device(dev);
 329                }
 330
 331                status = -ENODEV;
 332                goto free_tdev;
 333        }
 334
 335        /* the second configuration must be set */
 336        if (dev->actconfig->desc.bConfigurationValue == TI_BOOT_CONFIG) {
 337                status = usb_driver_set_configuration(dev, TI_ACTIVE_CONFIG);
 338                status = status ? status : -ENODEV;
 339                goto free_tdev;
 340        }
 341
 342        return 0;
 343
 344free_tdev:
 345        kfree(tdev);
 346        usb_set_serial_data(serial, NULL);
 347        return status;
 348}
 349
 350
 351static void ti_release(struct usb_serial *serial)
 352{
 353        struct ti_device *tdev = usb_get_serial_data(serial);
 354
 355        kfree(tdev);
 356}
 357
 358static int ti_port_probe(struct usb_serial_port *port)
 359{
 360        struct ti_port *tport;
 361
 362        tport = kzalloc(sizeof(*tport), GFP_KERNEL);
 363        if (!tport)
 364                return -ENOMEM;
 365
 366        spin_lock_init(&tport->tp_lock);
 367        if (port == port->serial->port[0])
 368                tport->tp_uart_base_addr = TI_UART1_BASE_ADDR;
 369        else
 370                tport->tp_uart_base_addr = TI_UART2_BASE_ADDR;
 371        port->port.closing_wait = msecs_to_jiffies(10 * closing_wait);
 372        tport->tp_port = port;
 373        tport->tp_tdev = usb_get_serial_data(port->serial);
 374        tport->tp_uart_mode = 0;        /* default is RS232 */
 375
 376        usb_set_serial_port_data(port, tport);
 377
 378        port->port.drain_delay = 3;
 379
 380        return 0;
 381}
 382
 383static int ti_port_remove(struct usb_serial_port *port)
 384{
 385        struct ti_port *tport;
 386
 387        tport = usb_get_serial_port_data(port);
 388        kfree(tport);
 389
 390        return 0;
 391}
 392
 393static int ti_open(struct tty_struct *tty, struct usb_serial_port *port)
 394{
 395        struct ti_port *tport = usb_get_serial_port_data(port);
 396        struct ti_device *tdev;
 397        struct usb_device *dev;
 398        struct urb *urb;
 399        int port_number;
 400        int status;
 401        __u16 open_settings = (__u8)(TI_PIPE_MODE_CONTINOUS |
 402                             TI_PIPE_TIMEOUT_ENABLE |
 403                             (TI_TRANSFER_TIMEOUT << 2));
 404
 405        if (tport == NULL)
 406                return -ENODEV;
 407
 408        dev = port->serial->dev;
 409        tdev = tport->tp_tdev;
 410
 411        /* only one open on any port on a device at a time */
 412        if (mutex_lock_interruptible(&tdev->td_open_close_lock))
 413                return -ERESTARTSYS;
 414
 415        port_number = port->port_number;
 416
 417        tport->tp_msr = 0;
 418        tport->tp_shadow_mcr |= (TI_MCR_RTS | TI_MCR_DTR);
 419
 420        /* start interrupt urb the first time a port is opened on this device */
 421        if (tdev->td_open_port_count == 0) {
 422                dev_dbg(&port->dev, "%s - start interrupt in urb\n", __func__);
 423                urb = tdev->td_serial->port[0]->interrupt_in_urb;
 424                if (!urb) {
 425                        dev_err(&port->dev, "%s - no interrupt urb\n", __func__);
 426                        status = -EINVAL;
 427                        goto release_lock;
 428                }
 429                urb->context = tdev;
 430                status = usb_submit_urb(urb, GFP_KERNEL);
 431                if (status) {
 432                        dev_err(&port->dev, "%s - submit interrupt urb failed, %d\n", __func__, status);
 433                        goto release_lock;
 434                }
 435        }
 436
 437        if (tty)
 438                ti_set_termios(tty, port, &tty->termios);
 439
 440        dev_dbg(&port->dev, "%s - sending TI_OPEN_PORT\n", __func__);
 441        status = ti_command_out_sync(tdev, TI_OPEN_PORT,
 442                (__u8)(TI_UART1_PORT + port_number), open_settings, NULL, 0);
 443        if (status) {
 444                dev_err(&port->dev, "%s - cannot send open command, %d\n",
 445                        __func__, status);
 446                goto unlink_int_urb;
 447        }
 448
 449        dev_dbg(&port->dev, "%s - sending TI_START_PORT\n", __func__);
 450        status = ti_command_out_sync(tdev, TI_START_PORT,
 451                (__u8)(TI_UART1_PORT + port_number), 0, NULL, 0);
 452        if (status) {
 453                dev_err(&port->dev, "%s - cannot send start command, %d\n",
 454                                                        __func__, status);
 455                goto unlink_int_urb;
 456        }
 457
 458        dev_dbg(&port->dev, "%s - sending TI_PURGE_PORT\n", __func__);
 459        status = ti_command_out_sync(tdev, TI_PURGE_PORT,
 460                (__u8)(TI_UART1_PORT + port_number), TI_PURGE_INPUT, NULL, 0);
 461        if (status) {
 462                dev_err(&port->dev, "%s - cannot clear input buffers, %d\n",
 463                                                        __func__, status);
 464                goto unlink_int_urb;
 465        }
 466        status = ti_command_out_sync(tdev, TI_PURGE_PORT,
 467                (__u8)(TI_UART1_PORT + port_number), TI_PURGE_OUTPUT, NULL, 0);
 468        if (status) {
 469                dev_err(&port->dev, "%s - cannot clear output buffers, %d\n",
 470                                                        __func__, status);
 471                goto unlink_int_urb;
 472        }
 473
 474        /* reset the data toggle on the bulk endpoints to work around bug in
 475         * host controllers where things get out of sync some times */
 476        usb_clear_halt(dev, port->write_urb->pipe);
 477        usb_clear_halt(dev, port->read_urb->pipe);
 478
 479        if (tty)
 480                ti_set_termios(tty, port, &tty->termios);
 481
 482        dev_dbg(&port->dev, "%s - sending TI_OPEN_PORT (2)\n", __func__);
 483        status = ti_command_out_sync(tdev, TI_OPEN_PORT,
 484                (__u8)(TI_UART1_PORT + port_number), open_settings, NULL, 0);
 485        if (status) {
 486                dev_err(&port->dev, "%s - cannot send open command (2), %d\n",
 487                                                        __func__, status);
 488                goto unlink_int_urb;
 489        }
 490
 491        dev_dbg(&port->dev, "%s - sending TI_START_PORT (2)\n", __func__);
 492        status = ti_command_out_sync(tdev, TI_START_PORT,
 493                (__u8)(TI_UART1_PORT + port_number), 0, NULL, 0);
 494        if (status) {
 495                dev_err(&port->dev, "%s - cannot send start command (2), %d\n",
 496                                                        __func__, status);
 497                goto unlink_int_urb;
 498        }
 499
 500        /* start read urb */
 501        dev_dbg(&port->dev, "%s - start read urb\n", __func__);
 502        urb = port->read_urb;
 503        if (!urb) {
 504                dev_err(&port->dev, "%s - no read urb\n", __func__);
 505                status = -EINVAL;
 506                goto unlink_int_urb;
 507        }
 508        tport->tp_read_urb_state = TI_READ_URB_RUNNING;
 509        urb->context = tport;
 510        status = usb_submit_urb(urb, GFP_KERNEL);
 511        if (status) {
 512                dev_err(&port->dev, "%s - submit read urb failed, %d\n",
 513                                                        __func__, status);
 514                goto unlink_int_urb;
 515        }
 516
 517        tport->tp_is_open = 1;
 518        ++tdev->td_open_port_count;
 519
 520        goto release_lock;
 521
 522unlink_int_urb:
 523        if (tdev->td_open_port_count == 0)
 524                usb_kill_urb(port->serial->port[0]->interrupt_in_urb);
 525release_lock:
 526        mutex_unlock(&tdev->td_open_close_lock);
 527        dev_dbg(&port->dev, "%s - exit %d\n", __func__, status);
 528        return status;
 529}
 530
 531
 532static void ti_close(struct usb_serial_port *port)
 533{
 534        struct ti_device *tdev;
 535        struct ti_port *tport;
 536        int port_number;
 537        int status;
 538        int do_unlock;
 539        unsigned long flags;
 540
 541        tdev = usb_get_serial_data(port->serial);
 542        tport = usb_get_serial_port_data(port);
 543        if (tdev == NULL || tport == NULL)
 544                return;
 545
 546        tport->tp_is_open = 0;
 547
 548        usb_kill_urb(port->read_urb);
 549        usb_kill_urb(port->write_urb);
 550        tport->tp_write_urb_in_use = 0;
 551        spin_lock_irqsave(&tport->tp_lock, flags);
 552        kfifo_reset_out(&port->write_fifo);
 553        spin_unlock_irqrestore(&tport->tp_lock, flags);
 554
 555        port_number = port->port_number;
 556
 557        dev_dbg(&port->dev, "%s - sending TI_CLOSE_PORT\n", __func__);
 558        status = ti_command_out_sync(tdev, TI_CLOSE_PORT,
 559                     (__u8)(TI_UART1_PORT + port_number), 0, NULL, 0);
 560        if (status)
 561                dev_err(&port->dev,
 562                        "%s - cannot send close port command, %d\n"
 563                                                        , __func__, status);
 564
 565        /* if mutex_lock is interrupted, continue anyway */
 566        do_unlock = !mutex_lock_interruptible(&tdev->td_open_close_lock);
 567        --tport->tp_tdev->td_open_port_count;
 568        if (tport->tp_tdev->td_open_port_count <= 0) {
 569                /* last port is closed, shut down interrupt urb */
 570                usb_kill_urb(port->serial->port[0]->interrupt_in_urb);
 571                tport->tp_tdev->td_open_port_count = 0;
 572        }
 573        if (do_unlock)
 574                mutex_unlock(&tdev->td_open_close_lock);
 575}
 576
 577
 578static int ti_write(struct tty_struct *tty, struct usb_serial_port *port,
 579                        const unsigned char *data, int count)
 580{
 581        struct ti_port *tport = usb_get_serial_port_data(port);
 582
 583        if (count == 0) {
 584                dev_dbg(&port->dev, "%s - write request of 0 bytes\n", __func__);
 585                return 0;
 586        }
 587
 588        if (tport == NULL || !tport->tp_is_open)
 589                return -ENODEV;
 590
 591        count = kfifo_in_locked(&port->write_fifo, data, count,
 592                                                        &tport->tp_lock);
 593        ti_send(tport);
 594
 595        return count;
 596}
 597
 598
 599static int ti_write_room(struct tty_struct *tty)
 600{
 601        struct usb_serial_port *port = tty->driver_data;
 602        struct ti_port *tport = usb_get_serial_port_data(port);
 603        int room = 0;
 604        unsigned long flags;
 605
 606        if (tport == NULL)
 607                return 0;
 608
 609        spin_lock_irqsave(&tport->tp_lock, flags);
 610        room = kfifo_avail(&port->write_fifo);
 611        spin_unlock_irqrestore(&tport->tp_lock, flags);
 612
 613        dev_dbg(&port->dev, "%s - returns %d\n", __func__, room);
 614        return room;
 615}
 616
 617
 618static int ti_chars_in_buffer(struct tty_struct *tty)
 619{
 620        struct usb_serial_port *port = tty->driver_data;
 621        struct ti_port *tport = usb_get_serial_port_data(port);
 622        int chars = 0;
 623        unsigned long flags;
 624
 625        if (tport == NULL)
 626                return 0;
 627
 628        spin_lock_irqsave(&tport->tp_lock, flags);
 629        chars = kfifo_len(&port->write_fifo);
 630        spin_unlock_irqrestore(&tport->tp_lock, flags);
 631
 632        dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars);
 633        return chars;
 634}
 635
 636static bool ti_tx_empty(struct usb_serial_port *port)
 637{
 638        struct ti_port *tport = usb_get_serial_port_data(port);
 639        int ret;
 640        u8 lsr;
 641
 642        ret = ti_get_lsr(tport, &lsr);
 643        if (!ret && !(lsr & TI_LSR_TX_EMPTY))
 644                return false;
 645
 646        return true;
 647}
 648
 649static void ti_throttle(struct tty_struct *tty)
 650{
 651        struct usb_serial_port *port = tty->driver_data;
 652        struct ti_port *tport = usb_get_serial_port_data(port);
 653
 654        if (tport == NULL)
 655                return;
 656
 657        if (I_IXOFF(tty) || C_CRTSCTS(tty))
 658                ti_stop_read(tport, tty);
 659
 660}
 661
 662
 663static void ti_unthrottle(struct tty_struct *tty)
 664{
 665        struct usb_serial_port *port = tty->driver_data;
 666        struct ti_port *tport = usb_get_serial_port_data(port);
 667        int status;
 668
 669        if (tport == NULL)
 670                return;
 671
 672        if (I_IXOFF(tty) || C_CRTSCTS(tty)) {
 673                status = ti_restart_read(tport, tty);
 674                if (status)
 675                        dev_err(&port->dev, "%s - cannot restart read, %d\n",
 676                                                        __func__, status);
 677        }
 678}
 679
 680static int ti_ioctl(struct tty_struct *tty,
 681        unsigned int cmd, unsigned long arg)
 682{
 683        struct usb_serial_port *port = tty->driver_data;
 684        struct ti_port *tport = usb_get_serial_port_data(port);
 685
 686        if (tport == NULL)
 687                return -ENODEV;
 688
 689        switch (cmd) {
 690        case TIOCGSERIAL:
 691                dev_dbg(&port->dev, "%s - TIOCGSERIAL\n", __func__);
 692                return ti_get_serial_info(tport,
 693                                (struct serial_struct __user *)arg);
 694        case TIOCSSERIAL:
 695                dev_dbg(&port->dev, "%s - TIOCSSERIAL\n", __func__);
 696                return ti_set_serial_info(tty, tport,
 697                                (struct serial_struct __user *)arg);
 698        }
 699        return -ENOIOCTLCMD;
 700}
 701
 702
 703static void ti_set_termios(struct tty_struct *tty,
 704                struct usb_serial_port *port, struct ktermios *old_termios)
 705{
 706        struct ti_port *tport = usb_get_serial_port_data(port);
 707        struct ti_uart_config *config;
 708        tcflag_t cflag, iflag;
 709        int baud;
 710        int status;
 711        int port_number = port->port_number;
 712        unsigned int mcr;
 713
 714        cflag = tty->termios.c_cflag;
 715        iflag = tty->termios.c_iflag;
 716
 717        dev_dbg(&port->dev, "%s - cflag %08x, iflag %08x\n", __func__, cflag, iflag);
 718        dev_dbg(&port->dev, "%s - old clfag %08x, old iflag %08x\n", __func__,
 719                old_termios->c_cflag, old_termios->c_iflag);
 720
 721        if (tport == NULL)
 722                return;
 723
 724        config = kmalloc(sizeof(*config), GFP_KERNEL);
 725        if (!config)
 726                return;
 727
 728        config->wFlags = 0;
 729
 730        /* these flags must be set */
 731        config->wFlags |= TI_UART_ENABLE_MS_INTS;
 732        config->wFlags |= TI_UART_ENABLE_AUTO_START_DMA;
 733        config->bUartMode = (__u8)(tport->tp_uart_mode);
 734
 735        switch (cflag & CSIZE) {
 736        case CS5:
 737                    config->bDataBits = TI_UART_5_DATA_BITS;
 738                    break;
 739        case CS6:
 740                    config->bDataBits = TI_UART_6_DATA_BITS;
 741                    break;
 742        case CS7:
 743                    config->bDataBits = TI_UART_7_DATA_BITS;
 744                    break;
 745        default:
 746        case CS8:
 747                    config->bDataBits = TI_UART_8_DATA_BITS;
 748                    break;
 749        }
 750
 751        /* CMSPAR isn't supported by this driver */
 752        tty->termios.c_cflag &= ~CMSPAR;
 753
 754        if (cflag & PARENB) {
 755                if (cflag & PARODD) {
 756                        config->wFlags |= TI_UART_ENABLE_PARITY_CHECKING;
 757                        config->bParity = TI_UART_ODD_PARITY;
 758                } else {
 759                        config->wFlags |= TI_UART_ENABLE_PARITY_CHECKING;
 760                        config->bParity = TI_UART_EVEN_PARITY;
 761                }
 762        } else {
 763                config->wFlags &= ~TI_UART_ENABLE_PARITY_CHECKING;
 764                config->bParity = TI_UART_NO_PARITY;
 765        }
 766
 767        if (cflag & CSTOPB)
 768                config->bStopBits = TI_UART_2_STOP_BITS;
 769        else
 770                config->bStopBits = TI_UART_1_STOP_BITS;
 771
 772        if (cflag & CRTSCTS) {
 773                /* RTS flow control must be off to drop RTS for baud rate B0 */
 774                if ((cflag & CBAUD) != B0)
 775                        config->wFlags |= TI_UART_ENABLE_RTS_IN;
 776                config->wFlags |= TI_UART_ENABLE_CTS_OUT;
 777        } else {
 778                ti_restart_read(tport, tty);
 779        }
 780
 781        if (I_IXOFF(tty) || I_IXON(tty)) {
 782                config->cXon  = START_CHAR(tty);
 783                config->cXoff = STOP_CHAR(tty);
 784
 785                if (I_IXOFF(tty))
 786                        config->wFlags |= TI_UART_ENABLE_X_IN;
 787                else
 788                        ti_restart_read(tport, tty);
 789
 790                if (I_IXON(tty))
 791                        config->wFlags |= TI_UART_ENABLE_X_OUT;
 792        }
 793
 794        baud = tty_get_baud_rate(tty);
 795        if (!baud)
 796                baud = 9600;
 797        if (tport->tp_tdev->td_is_3410)
 798                config->wBaudRate = (__u16)((923077 + baud/2) / baud);
 799        else
 800                config->wBaudRate = (__u16)((461538 + baud/2) / baud);
 801
 802        /* FIXME: Should calculate resulting baud here and report it back */
 803        if ((cflag & CBAUD) != B0)
 804                tty_encode_baud_rate(tty, baud, baud);
 805
 806        dev_dbg(&port->dev,
 807                "%s - BaudRate=%d, wBaudRate=%d, wFlags=0x%04X, bDataBits=%d, bParity=%d, bStopBits=%d, cXon=%d, cXoff=%d, bUartMode=%d\n",
 808                __func__, baud, config->wBaudRate, config->wFlags,
 809                config->bDataBits, config->bParity, config->bStopBits,
 810                config->cXon, config->cXoff, config->bUartMode);
 811
 812        cpu_to_be16s(&config->wBaudRate);
 813        cpu_to_be16s(&config->wFlags);
 814
 815        status = ti_command_out_sync(tport->tp_tdev, TI_SET_CONFIG,
 816                (__u8)(TI_UART1_PORT + port_number), 0, (__u8 *)config,
 817                sizeof(*config));
 818        if (status)
 819                dev_err(&port->dev, "%s - cannot set config on port %d, %d\n",
 820                                        __func__, port_number, status);
 821
 822        /* SET_CONFIG asserts RTS and DTR, reset them correctly */
 823        mcr = tport->tp_shadow_mcr;
 824        /* if baud rate is B0, clear RTS and DTR */
 825        if ((cflag & CBAUD) == B0)
 826                mcr &= ~(TI_MCR_DTR | TI_MCR_RTS);
 827        status = ti_set_mcr(tport, mcr);
 828        if (status)
 829                dev_err(&port->dev,
 830                        "%s - cannot set modem control on port %d, %d\n",
 831                                                __func__, port_number, status);
 832
 833        kfree(config);
 834}
 835
 836
 837static int ti_tiocmget(struct tty_struct *tty)
 838{
 839        struct usb_serial_port *port = tty->driver_data;
 840        struct ti_port *tport = usb_get_serial_port_data(port);
 841        unsigned int result;
 842        unsigned int msr;
 843        unsigned int mcr;
 844        unsigned long flags;
 845
 846        if (tport == NULL)
 847                return -ENODEV;
 848
 849        spin_lock_irqsave(&tport->tp_lock, flags);
 850        msr = tport->tp_msr;
 851        mcr = tport->tp_shadow_mcr;
 852        spin_unlock_irqrestore(&tport->tp_lock, flags);
 853
 854        result = ((mcr & TI_MCR_DTR) ? TIOCM_DTR : 0)
 855                | ((mcr & TI_MCR_RTS) ? TIOCM_RTS : 0)
 856                | ((mcr & TI_MCR_LOOP) ? TIOCM_LOOP : 0)
 857                | ((msr & TI_MSR_CTS) ? TIOCM_CTS : 0)
 858                | ((msr & TI_MSR_CD) ? TIOCM_CAR : 0)
 859                | ((msr & TI_MSR_RI) ? TIOCM_RI : 0)
 860                | ((msr & TI_MSR_DSR) ? TIOCM_DSR : 0);
 861
 862        dev_dbg(&port->dev, "%s - 0x%04X\n", __func__, result);
 863
 864        return result;
 865}
 866
 867
 868static int ti_tiocmset(struct tty_struct *tty,
 869                                unsigned int set, unsigned int clear)
 870{
 871        struct usb_serial_port *port = tty->driver_data;
 872        struct ti_port *tport = usb_get_serial_port_data(port);
 873        unsigned int mcr;
 874        unsigned long flags;
 875
 876        if (tport == NULL)
 877                return -ENODEV;
 878
 879        spin_lock_irqsave(&tport->tp_lock, flags);
 880        mcr = tport->tp_shadow_mcr;
 881
 882        if (set & TIOCM_RTS)
 883                mcr |= TI_MCR_RTS;
 884        if (set & TIOCM_DTR)
 885                mcr |= TI_MCR_DTR;
 886        if (set & TIOCM_LOOP)
 887                mcr |= TI_MCR_LOOP;
 888
 889        if (clear & TIOCM_RTS)
 890                mcr &= ~TI_MCR_RTS;
 891        if (clear & TIOCM_DTR)
 892                mcr &= ~TI_MCR_DTR;
 893        if (clear & TIOCM_LOOP)
 894                mcr &= ~TI_MCR_LOOP;
 895        spin_unlock_irqrestore(&tport->tp_lock, flags);
 896
 897        return ti_set_mcr(tport, mcr);
 898}
 899
 900
 901static void ti_break(struct tty_struct *tty, int break_state)
 902{
 903        struct usb_serial_port *port = tty->driver_data;
 904        struct ti_port *tport = usb_get_serial_port_data(port);
 905        int status;
 906
 907        dev_dbg(&port->dev, "%s - state = %d\n", __func__, break_state);
 908
 909        if (tport == NULL)
 910                return;
 911
 912        status = ti_write_byte(port, tport->tp_tdev,
 913                tport->tp_uart_base_addr + TI_UART_OFFSET_LCR,
 914                TI_LCR_BREAK, break_state == -1 ? TI_LCR_BREAK : 0);
 915
 916        if (status)
 917                dev_dbg(&port->dev, "%s - error setting break, %d\n", __func__, status);
 918}
 919
 920
 921static void ti_interrupt_callback(struct urb *urb)
 922{
 923        struct ti_device *tdev = urb->context;
 924        struct usb_serial_port *port;
 925        struct usb_serial *serial = tdev->td_serial;
 926        struct ti_port *tport;
 927        struct device *dev = &urb->dev->dev;
 928        unsigned char *data = urb->transfer_buffer;
 929        int length = urb->actual_length;
 930        int port_number;
 931        int function;
 932        int status = urb->status;
 933        int retval;
 934        __u8 msr;
 935
 936        switch (status) {
 937        case 0:
 938                break;
 939        case -ECONNRESET:
 940        case -ENOENT:
 941        case -ESHUTDOWN:
 942                dev_dbg(dev, "%s - urb shutting down, %d\n", __func__, status);
 943                tdev->td_urb_error = 1;
 944                return;
 945        default:
 946                dev_err(dev, "%s - nonzero urb status, %d\n", __func__, status);
 947                tdev->td_urb_error = 1;
 948                goto exit;
 949        }
 950
 951        if (length != 2) {
 952                dev_dbg(dev, "%s - bad packet size, %d\n", __func__, length);
 953                goto exit;
 954        }
 955
 956        if (data[0] == TI_CODE_HARDWARE_ERROR) {
 957                dev_err(dev, "%s - hardware error, %d\n", __func__, data[1]);
 958                goto exit;
 959        }
 960
 961        port_number = TI_GET_PORT_FROM_CODE(data[0]);
 962        function = TI_GET_FUNC_FROM_CODE(data[0]);
 963
 964        dev_dbg(dev, "%s - port_number %d, function %d, data 0x%02X\n",
 965                __func__, port_number, function, data[1]);
 966
 967        if (port_number >= serial->num_ports) {
 968                dev_err(dev, "%s - bad port number, %d\n",
 969                                                __func__, port_number);
 970                goto exit;
 971        }
 972
 973        port = serial->port[port_number];
 974
 975        tport = usb_get_serial_port_data(port);
 976        if (!tport)
 977                goto exit;
 978
 979        switch (function) {
 980        case TI_CODE_DATA_ERROR:
 981                dev_err(dev, "%s - DATA ERROR, port %d, data 0x%02X\n",
 982                        __func__, port_number, data[1]);
 983                break;
 984
 985        case TI_CODE_MODEM_STATUS:
 986                msr = data[1];
 987                dev_dbg(dev, "%s - port %d, msr 0x%02X\n", __func__, port_number, msr);
 988                ti_handle_new_msr(tport, msr);
 989                break;
 990
 991        default:
 992                dev_err(dev, "%s - unknown interrupt code, 0x%02X\n",
 993                                                        __func__, data[1]);
 994                break;
 995        }
 996
 997exit:
 998        retval = usb_submit_urb(urb, GFP_ATOMIC);
 999        if (retval)
1000                dev_err(dev, "%s - resubmit interrupt urb failed, %d\n",
1001                        __func__, retval);
1002}
1003
1004
1005static void ti_bulk_in_callback(struct urb *urb)
1006{
1007        struct ti_port *tport = urb->context;
1008        struct usb_serial_port *port = tport->tp_port;
1009        struct device *dev = &urb->dev->dev;
1010        int status = urb->status;
1011        int retval = 0;
1012
1013        switch (status) {
1014        case 0:
1015                break;
1016        case -ECONNRESET:
1017        case -ENOENT:
1018        case -ESHUTDOWN:
1019                dev_dbg(dev, "%s - urb shutting down, %d\n", __func__, status);
1020                tport->tp_tdev->td_urb_error = 1;
1021                return;
1022        default:
1023                dev_err(dev, "%s - nonzero urb status, %d\n",
1024                        __func__, status);
1025                tport->tp_tdev->td_urb_error = 1;
1026        }
1027
1028        if (status == -EPIPE)
1029                goto exit;
1030
1031        if (status) {
1032                dev_err(dev, "%s - stopping read!\n", __func__);
1033                return;
1034        }
1035
1036        if (urb->actual_length) {
1037                usb_serial_debug_data(dev, __func__, urb->actual_length,
1038                                      urb->transfer_buffer);
1039
1040                if (!tport->tp_is_open)
1041                        dev_dbg(dev, "%s - port closed, dropping data\n",
1042                                __func__);
1043                else
1044                        ti_recv(port, urb->transfer_buffer, urb->actual_length);
1045                spin_lock(&tport->tp_lock);
1046                port->icount.rx += urb->actual_length;
1047                spin_unlock(&tport->tp_lock);
1048        }
1049
1050exit:
1051        /* continue to read unless stopping */
1052        spin_lock(&tport->tp_lock);
1053        if (tport->tp_read_urb_state == TI_READ_URB_RUNNING)
1054                retval = usb_submit_urb(urb, GFP_ATOMIC);
1055        else if (tport->tp_read_urb_state == TI_READ_URB_STOPPING)
1056                tport->tp_read_urb_state = TI_READ_URB_STOPPED;
1057
1058        spin_unlock(&tport->tp_lock);
1059        if (retval)
1060                dev_err(dev, "%s - resubmit read urb failed, %d\n",
1061                        __func__, retval);
1062}
1063
1064
1065static void ti_bulk_out_callback(struct urb *urb)
1066{
1067        struct ti_port *tport = urb->context;
1068        struct usb_serial_port *port = tport->tp_port;
1069        int status = urb->status;
1070
1071        tport->tp_write_urb_in_use = 0;
1072
1073        switch (status) {
1074        case 0:
1075                break;
1076        case -ECONNRESET:
1077        case -ENOENT:
1078        case -ESHUTDOWN:
1079                dev_dbg(&port->dev, "%s - urb shutting down, %d\n", __func__, status);
1080                tport->tp_tdev->td_urb_error = 1;
1081                return;
1082        default:
1083                dev_err_console(port, "%s - nonzero urb status, %d\n",
1084                        __func__, status);
1085                tport->tp_tdev->td_urb_error = 1;
1086        }
1087
1088        /* send any buffered data */
1089        ti_send(tport);
1090}
1091
1092
1093static void ti_recv(struct usb_serial_port *port, unsigned char *data,
1094                int length)
1095{
1096        int cnt;
1097
1098        do {
1099                cnt = tty_insert_flip_string(&port->port, data, length);
1100                if (cnt < length) {
1101                        dev_err(&port->dev, "%s - dropping data, %d bytes lost\n",
1102                                                __func__, length - cnt);
1103                        if (cnt == 0)
1104                                break;
1105                }
1106                tty_flip_buffer_push(&port->port);
1107                data += cnt;
1108                length -= cnt;
1109        } while (length > 0);
1110}
1111
1112
1113static void ti_send(struct ti_port *tport)
1114{
1115        int count, result;
1116        struct usb_serial_port *port = tport->tp_port;
1117        unsigned long flags;
1118
1119        spin_lock_irqsave(&tport->tp_lock, flags);
1120
1121        if (tport->tp_write_urb_in_use)
1122                goto unlock;
1123
1124        count = kfifo_out(&port->write_fifo,
1125                                port->write_urb->transfer_buffer,
1126                                port->bulk_out_size);
1127
1128        if (count == 0)
1129                goto unlock;
1130
1131        tport->tp_write_urb_in_use = 1;
1132
1133        spin_unlock_irqrestore(&tport->tp_lock, flags);
1134
1135        usb_serial_debug_data(&port->dev, __func__, count,
1136                              port->write_urb->transfer_buffer);
1137
1138        usb_fill_bulk_urb(port->write_urb, port->serial->dev,
1139                           usb_sndbulkpipe(port->serial->dev,
1140                                            port->bulk_out_endpointAddress),
1141                           port->write_urb->transfer_buffer, count,
1142                           ti_bulk_out_callback, tport);
1143
1144        result = usb_submit_urb(port->write_urb, GFP_ATOMIC);
1145        if (result) {
1146                dev_err_console(port, "%s - submit write urb failed, %d\n",
1147                                                        __func__, result);
1148                tport->tp_write_urb_in_use = 0;
1149                /* TODO: reschedule ti_send */
1150        } else {
1151                spin_lock_irqsave(&tport->tp_lock, flags);
1152                port->icount.tx += count;
1153                spin_unlock_irqrestore(&tport->tp_lock, flags);
1154        }
1155
1156        /* more room in the buffer for new writes, wakeup */
1157        tty_port_tty_wakeup(&port->port);
1158
1159        return;
1160unlock:
1161        spin_unlock_irqrestore(&tport->tp_lock, flags);
1162        return;
1163}
1164
1165
1166static int ti_set_mcr(struct ti_port *tport, unsigned int mcr)
1167{
1168        unsigned long flags;
1169        int status;
1170
1171        status = ti_write_byte(tport->tp_port, tport->tp_tdev,
1172                tport->tp_uart_base_addr + TI_UART_OFFSET_MCR,
1173                TI_MCR_RTS | TI_MCR_DTR | TI_MCR_LOOP, mcr);
1174
1175        spin_lock_irqsave(&tport->tp_lock, flags);
1176        if (!status)
1177                tport->tp_shadow_mcr = mcr;
1178        spin_unlock_irqrestore(&tport->tp_lock, flags);
1179
1180        return status;
1181}
1182
1183
1184static int ti_get_lsr(struct ti_port *tport, u8 *lsr)
1185{
1186        int size, status;
1187        struct ti_device *tdev = tport->tp_tdev;
1188        struct usb_serial_port *port = tport->tp_port;
1189        int port_number = port->port_number;
1190        struct ti_port_status *data;
1191
1192        size = sizeof(struct ti_port_status);
1193        data = kmalloc(size, GFP_KERNEL);
1194        if (!data)
1195                return -ENOMEM;
1196
1197        status = ti_command_in_sync(tdev, TI_GET_PORT_STATUS,
1198                (__u8)(TI_UART1_PORT+port_number), 0, (__u8 *)data, size);
1199        if (status) {
1200                dev_err(&port->dev,
1201                        "%s - get port status command failed, %d\n",
1202                                                        __func__, status);
1203                goto free_data;
1204        }
1205
1206        dev_dbg(&port->dev, "%s - lsr 0x%02X\n", __func__, data->bLSR);
1207
1208        *lsr = data->bLSR;
1209
1210free_data:
1211        kfree(data);
1212        return status;
1213}
1214
1215
1216static int ti_get_serial_info(struct ti_port *tport,
1217        struct serial_struct __user *ret_arg)
1218{
1219        struct usb_serial_port *port = tport->tp_port;
1220        struct serial_struct ret_serial;
1221        unsigned cwait;
1222
1223        if (!ret_arg)
1224                return -EFAULT;
1225
1226        cwait = port->port.closing_wait;
1227        if (cwait != ASYNC_CLOSING_WAIT_NONE)
1228                cwait = jiffies_to_msecs(cwait) / 10;
1229
1230        memset(&ret_serial, 0, sizeof(ret_serial));
1231
1232        ret_serial.type = PORT_16550A;
1233        ret_serial.line = port->minor;
1234        ret_serial.port = port->port_number;
1235        ret_serial.flags = tport->tp_flags;
1236        ret_serial.xmit_fifo_size = kfifo_size(&port->write_fifo);
1237        ret_serial.baud_base = tport->tp_tdev->td_is_3410 ? 921600 : 460800;
1238        ret_serial.closing_wait = cwait;
1239
1240        if (copy_to_user(ret_arg, &ret_serial, sizeof(*ret_arg)))
1241                return -EFAULT;
1242
1243        return 0;
1244}
1245
1246
1247static int ti_set_serial_info(struct tty_struct *tty, struct ti_port *tport,
1248        struct serial_struct __user *new_arg)
1249{
1250        struct serial_struct new_serial;
1251        unsigned cwait;
1252
1253        if (copy_from_user(&new_serial, new_arg, sizeof(new_serial)))
1254                return -EFAULT;
1255
1256        cwait = new_serial.closing_wait;
1257        if (cwait != ASYNC_CLOSING_WAIT_NONE)
1258                cwait = msecs_to_jiffies(10 * new_serial.closing_wait);
1259
1260        tport->tp_flags = new_serial.flags & TI_SET_SERIAL_FLAGS;
1261        tport->tp_port->port.closing_wait = cwait;
1262
1263        return 0;
1264}
1265
1266
1267static void ti_handle_new_msr(struct ti_port *tport, __u8 msr)
1268{
1269        struct async_icount *icount;
1270        struct tty_struct *tty;
1271        unsigned long flags;
1272
1273        dev_dbg(&tport->tp_port->dev, "%s - msr 0x%02X\n", __func__, msr);
1274
1275        if (msr & TI_MSR_DELTA_MASK) {
1276                spin_lock_irqsave(&tport->tp_lock, flags);
1277                icount = &tport->tp_port->icount;
1278                if (msr & TI_MSR_DELTA_CTS)
1279                        icount->cts++;
1280                if (msr & TI_MSR_DELTA_DSR)
1281                        icount->dsr++;
1282                if (msr & TI_MSR_DELTA_CD)
1283                        icount->dcd++;
1284                if (msr & TI_MSR_DELTA_RI)
1285                        icount->rng++;
1286                wake_up_interruptible(&tport->tp_port->port.delta_msr_wait);
1287                spin_unlock_irqrestore(&tport->tp_lock, flags);
1288        }
1289
1290        tport->tp_msr = msr & TI_MSR_MASK;
1291
1292        /* handle CTS flow control */
1293        tty = tty_port_tty_get(&tport->tp_port->port);
1294        if (tty && C_CRTSCTS(tty)) {
1295                if (msr & TI_MSR_CTS)
1296                        tty_wakeup(tty);
1297        }
1298        tty_kref_put(tty);
1299}
1300
1301
1302static void ti_stop_read(struct ti_port *tport, struct tty_struct *tty)
1303{
1304        unsigned long flags;
1305
1306        spin_lock_irqsave(&tport->tp_lock, flags);
1307
1308        if (tport->tp_read_urb_state == TI_READ_URB_RUNNING)
1309                tport->tp_read_urb_state = TI_READ_URB_STOPPING;
1310
1311        spin_unlock_irqrestore(&tport->tp_lock, flags);
1312}
1313
1314
1315static int ti_restart_read(struct ti_port *tport, struct tty_struct *tty)
1316{
1317        struct urb *urb;
1318        int status = 0;
1319        unsigned long flags;
1320
1321        spin_lock_irqsave(&tport->tp_lock, flags);
1322
1323        if (tport->tp_read_urb_state == TI_READ_URB_STOPPED) {
1324                tport->tp_read_urb_state = TI_READ_URB_RUNNING;
1325                urb = tport->tp_port->read_urb;
1326                spin_unlock_irqrestore(&tport->tp_lock, flags);
1327                urb->context = tport;
1328                status = usb_submit_urb(urb, GFP_KERNEL);
1329        } else  {
1330                tport->tp_read_urb_state = TI_READ_URB_RUNNING;
1331                spin_unlock_irqrestore(&tport->tp_lock, flags);
1332        }
1333
1334        return status;
1335}
1336
1337
1338static int ti_command_out_sync(struct ti_device *tdev, __u8 command,
1339        __u16 moduleid, __u16 value, __u8 *data, int size)
1340{
1341        int status;
1342
1343        status = usb_control_msg(tdev->td_serial->dev,
1344                usb_sndctrlpipe(tdev->td_serial->dev, 0), command,
1345                (USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT),
1346                value, moduleid, data, size, 1000);
1347
1348        if (status == size)
1349                status = 0;
1350
1351        if (status > 0)
1352                status = -ECOMM;
1353
1354        return status;
1355}
1356
1357
1358static int ti_command_in_sync(struct ti_device *tdev, __u8 command,
1359        __u16 moduleid, __u16 value, __u8 *data, int size)
1360{
1361        int status;
1362
1363        status = usb_control_msg(tdev->td_serial->dev,
1364                usb_rcvctrlpipe(tdev->td_serial->dev, 0), command,
1365                (USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN),
1366                value, moduleid, data, size, 1000);
1367
1368        if (status == size)
1369                status = 0;
1370
1371        if (status > 0)
1372                status = -ECOMM;
1373
1374        return status;
1375}
1376
1377
1378static int ti_write_byte(struct usb_serial_port *port,
1379                        struct ti_device *tdev, unsigned long addr,
1380                        __u8 mask, __u8 byte)
1381{
1382        int status;
1383        unsigned int size;
1384        struct ti_write_data_bytes *data;
1385
1386        dev_dbg(&port->dev, "%s - addr 0x%08lX, mask 0x%02X, byte 0x%02X\n", __func__,
1387                addr, mask, byte);
1388
1389        size = sizeof(struct ti_write_data_bytes) + 2;
1390        data = kmalloc(size, GFP_KERNEL);
1391        if (!data)
1392                return -ENOMEM;
1393
1394        data->bAddrType = TI_RW_DATA_ADDR_XDATA;
1395        data->bDataType = TI_RW_DATA_BYTE;
1396        data->bDataCounter = 1;
1397        data->wBaseAddrHi = cpu_to_be16(addr>>16);
1398        data->wBaseAddrLo = cpu_to_be16(addr);
1399        data->bData[0] = mask;
1400        data->bData[1] = byte;
1401
1402        status = ti_command_out_sync(tdev, TI_WRITE_DATA, TI_RAM_PORT, 0,
1403                (__u8 *)data, size);
1404
1405        if (status < 0)
1406                dev_err(&port->dev, "%s - failed, %d\n", __func__, status);
1407
1408        kfree(data);
1409
1410        return status;
1411}
1412
1413static int ti_do_download(struct usb_device *dev, int pipe,
1414                                                u8 *buffer, int size)
1415{
1416        int pos;
1417        u8 cs = 0;
1418        int done;
1419        struct ti_firmware_header *header;
1420        int status = 0;
1421        int len;
1422
1423        for (pos = sizeof(struct ti_firmware_header); pos < size; pos++)
1424                cs = (__u8)(cs + buffer[pos]);
1425
1426        header = (struct ti_firmware_header *)buffer;
1427        header->wLength = cpu_to_le16((__u16)(size
1428                                        - sizeof(struct ti_firmware_header)));
1429        header->bCheckSum = cs;
1430
1431        dev_dbg(&dev->dev, "%s - downloading firmware\n", __func__);
1432        for (pos = 0; pos < size; pos += done) {
1433                len = min(size - pos, TI_DOWNLOAD_MAX_PACKET_SIZE);
1434                status = usb_bulk_msg(dev, pipe, buffer + pos, len,
1435                                                                &done, 1000);
1436                if (status)
1437                        break;
1438        }
1439        return status;
1440}
1441
1442static int ti_download_firmware(struct ti_device *tdev)
1443{
1444        int status;
1445        int buffer_size;
1446        __u8 *buffer;
1447        struct usb_device *dev = tdev->td_serial->dev;
1448        unsigned int pipe = usb_sndbulkpipe(dev,
1449                tdev->td_serial->port[0]->bulk_out_endpointAddress);
1450        const struct firmware *fw_p;
1451        char buf[32];
1452
1453        /* try ID specific firmware first, then try generic firmware */
1454        sprintf(buf, "ti_usb-v%04x-p%04x.fw",
1455                        le16_to_cpu(dev->descriptor.idVendor),
1456                        le16_to_cpu(dev->descriptor.idProduct));
1457        status = request_firmware(&fw_p, buf, &dev->dev);
1458
1459        if (status != 0) {
1460                buf[0] = '\0';
1461                if (le16_to_cpu(dev->descriptor.idVendor) == MTS_VENDOR_ID) {
1462                        switch (le16_to_cpu(dev->descriptor.idProduct)) {
1463                        case MTS_CDMA_PRODUCT_ID:
1464                                strcpy(buf, "mts_cdma.fw");
1465                                break;
1466                        case MTS_GSM_PRODUCT_ID:
1467                                strcpy(buf, "mts_gsm.fw");
1468                                break;
1469                        case MTS_EDGE_PRODUCT_ID:
1470                                strcpy(buf, "mts_edge.fw");
1471                                break;
1472                        case MTS_MT9234MU_PRODUCT_ID:
1473                                strcpy(buf, "mts_mt9234mu.fw");
1474                                break;
1475                        case MTS_MT9234ZBA_PRODUCT_ID:
1476                                strcpy(buf, "mts_mt9234zba.fw");
1477                                break;
1478                        case MTS_MT9234ZBAOLD_PRODUCT_ID:
1479                                strcpy(buf, "mts_mt9234zba.fw");
1480                                break;                  }
1481                }
1482                if (buf[0] == '\0') {
1483                        if (tdev->td_is_3410)
1484                                strcpy(buf, "ti_3410.fw");
1485                        else
1486                                strcpy(buf, "ti_5052.fw");
1487                }
1488                status = request_firmware(&fw_p, buf, &dev->dev);
1489        }
1490        if (status) {
1491                dev_err(&dev->dev, "%s - firmware not found\n", __func__);
1492                return -ENOENT;
1493        }
1494        if (fw_p->size > TI_FIRMWARE_BUF_SIZE) {
1495                dev_err(&dev->dev, "%s - firmware too large %zu\n", __func__, fw_p->size);
1496                release_firmware(fw_p);
1497                return -ENOENT;
1498        }
1499
1500        buffer_size = TI_FIRMWARE_BUF_SIZE + sizeof(struct ti_firmware_header);
1501        buffer = kmalloc(buffer_size, GFP_KERNEL);
1502        if (buffer) {
1503                memcpy(buffer, fw_p->data, fw_p->size);
1504                memset(buffer + fw_p->size, 0xff, buffer_size - fw_p->size);
1505                status = ti_do_download(dev, pipe, buffer, fw_p->size);
1506                kfree(buffer);
1507        } else {
1508                status = -ENOMEM;
1509        }
1510        release_firmware(fw_p);
1511        if (status) {
1512                dev_err(&dev->dev, "%s - error downloading firmware, %d\n",
1513                                                        __func__, status);
1514                return status;
1515        }
1516
1517        dev_dbg(&dev->dev, "%s - download successful\n", __func__);
1518
1519        return 0;
1520}
1521