1/* 2 * mace.h - definitions for the registers in the Am79C940 MACE 3 * (Medium Access Control for Ethernet) controller. 4 * 5 * Copyright (C) 1996 Paul Mackerras. 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License 9 * as published by the Free Software Foundation; either version 10 * 2 of the License, or (at your option) any later version. 11 */ 12 13#define REG(x) volatile unsigned char x; char x ## _pad[15] 14 15struct mace { 16 REG(rcvfifo); /* receive FIFO */ 17 REG(xmtfifo); /* transmit FIFO */ 18 REG(xmtfc); /* transmit frame control */ 19 REG(xmtfs); /* transmit frame status */ 20 REG(xmtrc); /* transmit retry count */ 21 REG(rcvfc); /* receive frame control */ 22 REG(rcvfs); /* receive frame status (4 bytes) */ 23 REG(fifofc); /* FIFO frame count */ 24 REG(ir); /* interrupt register */ 25 REG(imr); /* interrupt mask register */ 26 REG(pr); /* poll register */ 27 REG(biucc); /* bus interface unit config control */ 28 REG(fifocc); /* FIFO configuration control */ 29 REG(maccc); /* medium access control config control */ 30 REG(plscc); /* phys layer signalling config control */ 31 REG(phycc); /* physical configuration control */ 32 REG(chipid_lo); /* chip ID, lsb */ 33 REG(chipid_hi); /* chip ID, msb */ 34 REG(iac); /* internal address config */ 35 REG(reg19); 36 REG(ladrf); /* logical address filter (8 bytes) */ 37 REG(padr); /* physical address (6 bytes) */ 38 REG(reg22); 39 REG(reg23); 40 REG(mpc); /* missed packet count (clears when read) */ 41 REG(reg25); 42 REG(rntpc); /* runt packet count (clears when read) */ 43 REG(rcvcc); /* recv collision count (clears when read) */ 44 REG(reg28); 45 REG(utr); /* user test reg */ 46 REG(reg30); 47 REG(reg31); 48}; 49 50/* Bits in XMTFC */ 51#define DRTRY 0x80 /* don't retry transmission after collision */ 52#define DXMTFCS 0x08 /* don't append FCS to transmitted frame */ 53#define AUTO_PAD_XMIT 0x01 /* auto-pad short packets on transmission */ 54 55/* Bits in XMTFS: only valid when XMTSV is set in PR and XMTFS */ 56#define XMTSV 0x80 /* transmit status (i.e. XMTFS) valid */ 57#define UFLO 0x40 /* underflow - xmit fifo ran dry */ 58#define LCOL 0x20 /* late collision (transmission aborted) */ 59#define MORE 0x10 /* 2 or more retries needed to xmit frame */ 60#define ONE 0x08 /* 1 retry needed to xmit frame */ 61#define DEFER 0x04 /* MACE had to defer xmission (enet busy) */ 62#define LCAR 0x02 /* loss of carrier (transmission aborted) */ 63#define RTRY 0x01 /* too many retries (transmission aborted) */ 64 65/* Bits in XMTRC: only valid when XMTSV is set in PR (and XMTFS) */ 66#define EXDEF 0x80 /* had to defer for excessive time */ 67#define RETRY_MASK 0x0f /* number of retries (0 - 15) */ 68 69/* Bits in RCVFC */ 70#define LLRCV 0x08 /* low latency receive: early DMA request */ 71#define M_RBAR 0x04 /* sets function of EAM/R pin */ 72#define AUTO_STRIP_RCV 0x01 /* auto-strip short LLC frames on recv */ 73 74/* 75 * Bits in RCVFS. After a frame is received, four bytes of status 76 * are automatically read from this register and appended to the frame 77 * data in memory. These are: 78 * Byte 0 and 1: message byte count and frame status 79 * Byte 2: runt packet count 80 * Byte 3: receive collision count 81 */ 82#define RS_OFLO 0x8000 /* receive FIFO overflowed */ 83#define RS_CLSN 0x4000 /* received frame suffered (late) collision */ 84#define RS_FRAMERR 0x2000 /* framing error flag */ 85#define RS_FCSERR 0x1000 /* frame had FCS error */ 86#define RS_COUNT 0x0fff /* mask for byte count field */ 87 88/* Bits (fields) in FIFOFC */ 89#define RCVFC_SH 4 /* receive frame count in FIFO */ 90#define RCVFC_MASK 0x0f 91#define XMTFC_SH 0 /* transmit frame count in FIFO */ 92#define XMTFC_MASK 0x0f 93 94/* 95 * Bits in IR and IMR. The IR clears itself when read. 96 * Setting a bit in the IMR will disable the corresponding interrupt. 97 */ 98#define JABBER 0x80 /* jabber error - 10baseT xmission too long */ 99#define BABBLE 0x40 /* babble - xmitter xmitting for too long */ 100#define CERR 0x20 /* collision err - no SQE test (heartbeat) */ 101#define RCVCCO 0x10 /* RCVCC overflow */ 102#define RNTPCO 0x08 /* RNTPC overflow */ 103#define MPCO 0x04 /* MPC overflow */ 104#define RCVINT 0x02 /* receive interrupt */ 105#define XMTINT 0x01 /* transmitter interrupt */ 106 107/* Bits in PR */ 108#define XMTSV 0x80 /* XMTFS valid (same as in XMTFS) */ 109#define TDTREQ 0x40 /* set when xmit fifo is requesting data */ 110#define RDTREQ 0x20 /* set when recv fifo requests data xfer */ 111 112/* Bits in BIUCC */ 113#define BSWP 0x40 /* byte swap, i.e. big-endian bus */ 114#define XMTSP_4 0x00 /* start xmitting when 4 bytes in FIFO */ 115#define XMTSP_16 0x10 /* start xmitting when 16 bytes in FIFO */ 116#define XMTSP_64 0x20 /* start xmitting when 64 bytes in FIFO */ 117#define XMTSP_112 0x30 /* start xmitting when 112 bytes in FIFO */ 118#define SWRST 0x01 /* software reset */ 119 120/* Bits in FIFOCC */ 121#define XMTFW_8 0x00 /* xmit fifo watermark = 8 words free */ 122#define XMTFW_16 0x40 /* 16 words free */ 123#define XMTFW_32 0x80 /* 32 words free */ 124#define RCVFW_16 0x00 /* recv fifo watermark = 16 bytes avail */ 125#define RCVFW_32 0x10 /* 32 bytes avail */ 126#define RCVFW_64 0x20 /* 64 bytes avail */ 127#define XMTFWU 0x08 /* xmit fifo watermark update enable */ 128#define RCVFWU 0x04 /* recv fifo watermark update enable */ 129#define XMTBRST 0x02 /* enable transmit burst mode */ 130#define RCVBRST 0x01 /* enable receive burst mode */ 131 132/* Bits in MACCC */ 133#define PROM 0x80 /* promiscuous mode */ 134#define DXMT2PD 0x40 /* disable xmit two-part deferral algorithm */ 135#define EMBA 0x20 /* enable modified backoff algorithm */ 136#define DRCVPA 0x08 /* disable receiving physical address */ 137#define DRCVBC 0x04 /* disable receiving broadcasts */ 138#define ENXMT 0x02 /* enable transmitter */ 139#define ENRCV 0x01 /* enable receiver */ 140 141/* Bits in PLSCC */ 142#define XMTSEL 0x08 /* select DO+/DO- state when idle */ 143#define PORTSEL_AUI 0x00 /* select AUI port */ 144#define PORTSEL_10T 0x02 /* select 10Base-T port */ 145#define PORTSEL_DAI 0x04 /* select DAI port */ 146#define PORTSEL_GPSI 0x06 /* select GPSI port */ 147#define ENPLSIO 0x01 /* enable optional PLS I/O pins */ 148 149/* Bits in PHYCC */ 150#define LNKFL 0x80 /* reports 10Base-T link failure */ 151#define DLNKTST 0x40 /* disable 10Base-T link test */ 152#define REVPOL 0x20 /* 10Base-T receiver polarity reversed */ 153#define DAPC 0x10 /* disable auto receiver polarity correction */ 154#define LRT 0x08 /* low receive threshold for long links */ 155#define ASEL 0x04 /* auto-select AUI or 10Base-T port */ 156#define RWAKE 0x02 /* remote wake function */ 157#define AWAKE 0x01 /* auto wake function */ 158 159/* Bits in IAC */ 160#define ADDRCHG 0x80 /* request address change */ 161#define PHYADDR 0x04 /* access physical address */ 162#define LOGADDR 0x02 /* access multicast filter */ 163 164/* Bits in UTR */ 165#define RTRE 0x80 /* reserved test register enable. DON'T SET. */ 166#define RTRD 0x40 /* reserved test register disable. Sticky */ 167#define RPAC 0x20 /* accept runt packets */ 168#define FCOLL 0x10 /* force collision */ 169#define RCVFCSE 0x08 /* receive FCS enable */ 170#define LOOP_NONE 0x00 /* no loopback */ 171#define LOOP_EXT 0x02 /* external loopback */ 172#define LOOP_INT 0x04 /* internal loopback, excludes MENDEC */ 173#define LOOP_MENDEC 0x06 /* internal loopback, includes MENDEC */ 174