/*
*  sym53c500_cs.c       Bob Tracy (rct@frus.com)
*
*  A rewrite of the pcmcia-cs add-on driver for newer (circa 1997)
*  New Media Bus Toaster PCMCIA SCSI cards using the Symbios Logic
*  53c500 controller: intended for use with 2.6 and later kernels.
*  The pcmcia-cs add-on version of this driver is not supported
*  beyond 2.4.  It consisted of three files with history/copyright
*  information as follows:
*
*  SYM53C500.h
*       Bob Tracy (rct@frus.com)
*       Original by Tom Corner (tcorner@via.at).
*       Adapted from NCR53c406a.h which is Copyrighted (C) 1994
*       Normunds Saumanis (normunds@rx.tech.swh.lv)
*
*  SYM53C500.c
*       Bob Tracy (rct@frus.com)
*       Original driver by Tom Corner (tcorner@via.at) was adapted
*       from NCR53c406a.c which is Copyrighted (C) 1994, 1995, 1996 
*       Normunds Saumanis (normunds@fi.ibm.com)
*
*  sym53c500.c
*       Bob Tracy (rct@frus.com)
*       Original by Tom Corner (tcorner@via.at) was adapted from a
*       driver for the Qlogic SCSI card written by
*       David Hinds (dhinds@allegro.stanford.edu).
* 
*  This program is free software; you can redistribute it and/or modify it
*  under the terms of the GNU General Public License as published by the
*  Free Software Foundation; either version 2, or (at your option) any
*  later version.
*
*  This program is distributed in the hope that it will be useful, but
*  WITHOUT ANY WARRANTY; without even the implied warranty of
*  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
*  General Public License for more details.
*/

#define SYM53C500_DEBUG 0
#define VERBOSE_SYM53C500_DEBUG 0

/*
*  Set this to 0 if you encounter kernel lockups while transferring 
*  data in PIO mode.  Note this can be changed via "sysfs".
*/
#define USE_FAST_PIO 1

/* =============== End of user configurable parameters ============== */

#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/ioport.h>
#include <linux/blkdev.h>
#include <linux/spinlock.h>
#include <linux/bitops.h>

#include <asm/io.h>
#include <asm/dma.h>
#include <asm/irq.h>

#include <scsi/scsi_ioctl.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_device.h>
#include <scsi/scsi.h>
#include <scsi/scsi_host.h>

#include <pcmcia/cistpl.h>
#include <pcmcia/ds.h>
#include <pcmcia/ciscode.h>


/* ================================================================== */

#define SYNC_MODE 0             /* Synchronous transfer mode */

/* Default configuration */
#define C1_IMG   0x07           /* ID=7 */
#define C2_IMG   0x48           /* FE SCSI2 */
#define C3_IMG   0x20           /* CDB */
#define C4_IMG   0x04           /* ANE */
#define C5_IMG   0xa4           /* ? changed from b6= AA PI SIE POL */
#define C7_IMG   0x80           /* added for SYM53C500 t. corner */

/* Hardware Registers: offsets from io_port (base) */

/* Control Register Set 0 */
#define TC_LSB          0x00            /* transfer counter lsb */
#define TC_MSB          0x01            /* transfer counter msb */
#define SCSI_FIFO       0x02            /* scsi fifo register */
#define CMD_REG         0x03            /* command register */
#define STAT_REG        0x04            /* status register */
#define DEST_ID         0x04            /* selection/reselection bus id */
#define INT_REG         0x05            /* interrupt status register */
#define SRTIMOUT        0x05            /* select/reselect timeout reg */
#define SEQ_REG         0x06            /* sequence step register */
#define SYNCPRD         0x06            /* synchronous transfer period */
#define FIFO_FLAGS      0x07            /* indicates # of bytes in fifo */
#define SYNCOFF         0x07            /* synchronous offset register */
#define CONFIG1         0x08            /* configuration register */
#define CLKCONV         0x09            /* clock conversion register */
/* #define TESTREG      0x0A */         /* test mode register */
#define CONFIG2         0x0B            /* configuration 2 register */
#define CONFIG3         0x0C            /* configuration 3 register */
#define CONFIG4         0x0D            /* configuration 4 register */
#define TC_HIGH         0x0E            /* transfer counter high */
/* #define FIFO_BOTTOM  0x0F */         /* reserve FIFO byte register */

/* Control Register Set 1 */
/* #define JUMPER_SENSE 0x00 */         /* jumper sense port reg (r/w) */
/* #define SRAM_PTR     0x01 */         /* SRAM address pointer reg (r/w) */
/* #define SRAM_DATA    0x02 */         /* SRAM data register (r/w) */
#define PIO_FIFO        0x04            /* PIO FIFO registers (r/w) */
/* #define PIO_FIFO1    0x05 */         /*  */
/* #define PIO_FIFO2    0x06 */         /*  */
/* #define PIO_FIFO3    0x07 */         /*  */
#define PIO_STATUS      0x08            /* PIO status (r/w) */
/* #define ATA_CMD      0x09 */         /* ATA command/status reg (r/w) */
/* #define ATA_ERR      0x0A */         /* ATA features/error reg (r/w) */
#define PIO_FLAG        0x0B            /* PIO flag interrupt enable (r/w) */
#define CONFIG5         0x09            /* configuration 5 register */
/* #define SIGNATURE    0x0E */         /* signature register (r) */
/* #define CONFIG6      0x0F */         /* configuration 6 register (r) */
#define CONFIG7         0x0d

/* select register set 0 */
#define REG0(x)         (outb(C4_IMG, (x) + CONFIG4))
/* select register set 1 */
#define REG1(x)         outb(C7_IMG, (x) + CONFIG7); outb(C5_IMG, (x) + CONFIG5)

#if SYM53C500_DEBUG
#define DEB(x) x
#else
#define DEB(x)
#endif

#if VERBOSE_SYM53C500_DEBUG
#define VDEB(x) x
#else
#define VDEB(x)
#endif

#define LOAD_DMA_COUNT(x, count) \
  outb(count & 0xff, (x) + TC_LSB); \
  outb((count >> 8) & 0xff, (x) + TC_MSB); \
  outb((count >> 16) & 0xff, (x) + TC_HIGH);

/* Chip commands */
#define DMA_OP               0x80

#define SCSI_NOP             0x00
#define FLUSH_FIFO           0x01
#define CHIP_RESET           0x02
#define SCSI_RESET           0x03
#define RESELECT             0x40
#define SELECT_NO_ATN        0x41
#define SELECT_ATN           0x42
#define SELECT_ATN_STOP      0x43
#define ENABLE_SEL           0x44
#define DISABLE_SEL          0x45
#define SELECT_ATN3          0x46
#define RESELECT3            0x47
#define TRANSFER_INFO        0x10
#define INIT_CMD_COMPLETE    0x11
#define MSG_ACCEPT           0x12
#define TRANSFER_PAD         0x18
#define SET_ATN              0x1a
#define RESET_ATN            0x1b
#define SEND_MSG             0x20
#define SEND_STATUS          0x21
#define SEND_DATA            0x22
#define DISCONN_SEQ          0x23
#define TERMINATE_SEQ        0x24
#define TARG_CMD_COMPLETE    0x25
#define DISCONN              0x27
#define RECV_MSG             0x28
#define RECV_CMD             0x29
#define RECV_DATA            0x2a
#define RECV_CMD_SEQ         0x2b
#define TARGET_ABORT_DMA     0x04

/* ================================================================== */

struct scsi_info_t {
        struct pcmcia_device    *p_dev;
        struct Scsi_Host *host;
        unsigned short manf_id;
};

/*
*  Repository for per-instance host data.
*/
struct sym53c500_data {
        struct scsi_cmnd *current_SC;
        int fast_pio;
};

enum Phase {
    idle,
    data_out,
    data_in,
    command_ph,
    status_ph,
    message_out,
    message_in
};

/* ================================================================== */

static void
chip_init(int io_port)
{
        REG1(io_port);
        outb(0x01, io_port + PIO_STATUS);
        outb(0x00, io_port + PIO_FLAG);

        outb(C4_IMG, io_port + CONFIG4);        /* REG0(io_port); */
        outb(C3_IMG, io_port + CONFIG3);
        outb(C2_IMG, io_port + CONFIG2);
        outb(C1_IMG, io_port + CONFIG1);

        outb(0x05, io_port + CLKCONV);  /* clock conversion factor */
        outb(0x9C, io_port + SRTIMOUT); /* Selection timeout */
        outb(0x05, io_port + SYNCPRD);  /* Synchronous transfer period */
        outb(SYNC_MODE, io_port + SYNCOFF);     /* synchronous mode */  
}

static void
SYM53C500_int_host_reset(int io_port)
{
        outb(C4_IMG, io_port + CONFIG4);        /* REG0(io_port); */
        outb(CHIP_RESET, io_port + CMD_REG);
        outb(SCSI_NOP, io_port + CMD_REG);      /* required after reset */
        outb(SCSI_RESET, io_port + CMD_REG);
        chip_init(io_port);
}

static __inline__ int
SYM53C500_pio_read(int fast_pio, int base, unsigned char *request, unsigned int reqlen)
{
        int i;
        int len;        /* current scsi fifo size */

        REG1(base);
        while (reqlen) {
                i = inb(base + PIO_STATUS);
                /* VDEB(printk("pio_status=%x\n", i)); */
                if (i & 0x80) 
                        return 0;

                switch (i & 0x1e) {
                default:
                case 0x10:      /* fifo empty */
                        len = 0;
                        break;
                case 0x0:
                        len = 1;
                        break; 
                case 0x8:       /* fifo 1/3 full */
                        len = 42;
                        break;
                case 0xc:       /* fifo 2/3 full */
                        len = 84;
                        break;
                case 0xe:       /* fifo full */
                        len = 128;
                        break;
                }

                if ((i & 0x40) && len == 0) { /* fifo empty and interrupt occurred */
                        return 0;
                }

                if (len) {
                        if (len > reqlen) 
                                len = reqlen;

                        if (fast_pio && len > 3) {
                                insl(base + PIO_FIFO, request, len >> 2);
                                request += len & 0xfc; 
                                reqlen -= len & 0xfc; 
                        } else {
                                while (len--) {
                                        *request++ = inb(base + PIO_FIFO);
                                        reqlen--;
                                }
                        } 
                }
        }
        return 0;
}

static __inline__ int
SYM53C500_pio_write(int fast_pio, int base, unsigned char *request, unsigned int reqlen)
{
        int i = 0;
        int len;        /* current scsi fifo size */

        REG1(base);
        while (reqlen && !(i & 0x40)) {
                i = inb(base + PIO_STATUS);
                /* VDEB(printk("pio_status=%x\n", i)); */
                if (i & 0x80)   /* error */
                        return 0;

                switch (i & 0x1e) {
                case 0x10:
                        len = 128;
                        break;
                case 0x0:
                        len = 84;
                        break;
                case 0x8:
                        len = 42;
                        break;
                case 0xc:
                        len = 1;
                        break;
                default:
                case 0xe:
                        len = 0;
                        break;
                }

                if (len) {
                        if (len > reqlen)
                                len = reqlen;

                        if (fast_pio && len > 3) {
                                outsl(base + PIO_FIFO, request, len >> 2);
                                request += len & 0xfc;
                                reqlen -= len & 0xfc;
                        } else {
                                while (len--) {
                                        outb(*request++, base + PIO_FIFO);
                                        reqlen--;
                                }
                        }
                }
        }
        return 0;
}

static irqreturn_t
SYM53C500_intr(int irq, void *dev_id)
{
        unsigned long flags;
        struct Scsi_Host *dev = dev_id;
        DEB(unsigned char fifo_size;)
        DEB(unsigned char seq_reg;)
        unsigned char status, int_reg;
        unsigned char pio_status;
        int port_base = dev->io_port;
        struct sym53c500_data *data =
            (struct sym53c500_data *)dev->hostdata;
        struct scsi_cmnd *curSC = data->current_SC;
        int fast_pio = data->fast_pio;

        spin_lock_irqsave(dev->host_lock, flags);

        VDEB(printk("SYM53C500_intr called\n"));

        REG1(port_base);
        pio_status = inb(port_base + PIO_STATUS);
        REG0(port_base);
        status = inb(port_base + STAT_REG);
        DEB(seq_reg = inb(port_base + SEQ_REG));
        int_reg = inb(port_base + INT_REG);
        DEB(fifo_size = inb(port_base + FIFO_FLAGS) & 0x1f);

#if SYM53C500_DEBUG
        printk("status=%02x, seq_reg=%02x, int_reg=%02x, fifo_size=%02x", 
            status, seq_reg, int_reg, fifo_size);
        printk(", pio=%02x\n", pio_status);
#endif /* SYM53C500_DEBUG */

        if (int_reg & 0x80) {   /* SCSI reset intr */
                DEB(printk("SYM53C500: reset intr received\n"));
                curSC->result = DID_RESET << 16;
                goto idle_out;
        }

        if (pio_status & 0x80) {
                printk("SYM53C500: Warning: PIO error!\n");
                curSC->result = DID_ERROR << 16;
                goto idle_out;
        }

        if (status & 0x20) {            /* Parity error */
                printk("SYM53C500: Warning: parity error!\n");
                curSC->result = DID_PARITY << 16;
                goto idle_out;
        }

        if (status & 0x40) {            /* Gross error */
                printk("SYM53C500: Warning: gross error!\n");
                curSC->result = DID_ERROR << 16;
                goto idle_out;
        }

        if (int_reg & 0x20) {           /* Disconnect */
                DEB(printk("SYM53C500: disconnect intr received\n"));
                if (curSC->SCp.phase != message_in) {   /* Unexpected disconnect */
                        curSC->result = DID_NO_CONNECT << 16;
                } else {        /* Command complete, return status and message */
                        curSC->result = (curSC->SCp.Status & 0xff)
                            | ((curSC->SCp.Message & 0xff) << 8) | (DID_OK << 16);
                }
                goto idle_out;
        }

        switch (status & 0x07) {        /* scsi phase */
        case 0x00:                      /* DATA-OUT */
                if (int_reg & 0x10) {   /* Target requesting info transfer */
                        struct scatterlist *sg;
                        int i;

                        curSC->SCp.phase = data_out;
                        VDEB(printk("SYM53C500: Data-Out phase\n"));
                        outb(FLUSH_FIFO, port_base + CMD_REG);
                        LOAD_DMA_COUNT(port_base, scsi_bufflen(curSC)); /* Max transfer size */
                        outb(TRANSFER_INFO | DMA_OP, port_base + CMD_REG);

                        scsi_for_each_sg(curSC, sg, scsi_sg_count(curSC), i) {
                                SYM53C500_pio_write(fast_pio, port_base,
                                    sg_virt(sg), sg->length);
                        }
                        REG0(port_base);
                }
                break;

        case 0x01:              /* DATA-IN */
                if (int_reg & 0x10) {   /* Target requesting info transfer */
                        struct scatterlist *sg;
                        int i;

                        curSC->SCp.phase = data_in;
                        VDEB(printk("SYM53C500: Data-In phase\n"));
                        outb(FLUSH_FIFO, port_base + CMD_REG);
                        LOAD_DMA_COUNT(port_base, scsi_bufflen(curSC)); /* Max transfer size */
                        outb(TRANSFER_INFO | DMA_OP, port_base + CMD_REG);

                        scsi_for_each_sg(curSC, sg, scsi_sg_count(curSC), i) {
                                SYM53C500_pio_read(fast_pio, port_base,
                                        sg_virt(sg), sg->length);
                        }
                        REG0(port_base);
                }
                break;

        case 0x02:              /* COMMAND */
                curSC->SCp.phase = command_ph;
                printk("SYM53C500: Warning: Unknown interrupt occurred in command phase!\n");
                break;

        case 0x03:              /* STATUS */
                curSC->SCp.phase = status_ph;
                VDEB(printk("SYM53C500: Status phase\n"));
                outb(FLUSH_FIFO, port_base + CMD_REG);
                outb(INIT_CMD_COMPLETE, port_base + CMD_REG);
                break;

        case 0x04:              /* Reserved */
        case 0x05:              /* Reserved */
                printk("SYM53C500: WARNING: Reserved phase!!!\n");
                break;

        case 0x06:              /* MESSAGE-OUT */
                DEB(printk("SYM53C500: Message-Out phase\n"));
                curSC->SCp.phase = message_out;
                outb(SET_ATN, port_base + CMD_REG);     /* Reject the message */
                outb(MSG_ACCEPT, port_base + CMD_REG);
                break;

        case 0x07:              /* MESSAGE-IN */
                VDEB(printk("SYM53C500: Message-In phase\n"));
                curSC->SCp.phase = message_in;

                curSC->SCp.Status = inb(port_base + SCSI_FIFO);
                curSC->SCp.Message = inb(port_base + SCSI_FIFO);

                VDEB(printk("SCSI FIFO size=%d\n", inb(port_base + FIFO_FLAGS) & 0x1f));
                DEB(printk("Status = %02x  Message = %02x\n", curSC->SCp.Status, curSC->SCp.Message));

                if (curSC->SCp.Message == SAVE_POINTERS || curSC->SCp.Message == DISCONNECT) {
                        outb(SET_ATN, port_base + CMD_REG);     /* Reject message */
                        DEB(printk("Discarding SAVE_POINTERS message\n"));
                }
                outb(MSG_ACCEPT, port_base + CMD_REG);
                break;
        }
out:
        spin_unlock_irqrestore(dev->host_lock, flags);
        return IRQ_HANDLED;

idle_out:
        curSC->SCp.phase = idle;
        curSC->scsi_done(curSC);
        goto out;
}

static void
SYM53C500_release(struct pcmcia_device *link)
{
        struct scsi_info_t *info = link->priv;
        struct Scsi_Host *shost = info->host;

        dev_dbg(&link->dev, "SYM53C500_release\n");

        /*
        *  Do this before releasing/freeing resources.
        */
        scsi_remove_host(shost);

        /*
        *  Interrupts getting hosed on card removal.  Try
        *  the following code, mostly from qlogicfas.c.
        */
        if (shost->irq)
                free_irq(shost->irq, shost);
        if (shost->io_port && shost->n_io_port)
                release_region(shost->io_port, shost->n_io_port);

        pcmcia_disable_device(link);

        scsi_host_put(shost);
} /* SYM53C500_release */

static const char*
SYM53C500_info(struct Scsi_Host *SChost)
{
        static char info_msg[256];
        struct sym53c500_data *data =
            (struct sym53c500_data *)SChost->hostdata;

        DEB(printk("SYM53C500_info called\n"));
        (void)snprintf(info_msg, sizeof(info_msg),
            "SYM53C500 at 0x%lx, IRQ %d, %s PIO mode.", 
            SChost->io_port, SChost->irq, data->fast_pio ? "fast" : "slow");
        return (info_msg);
}

static int 
SYM53C500_queue_lck(struct scsi_cmnd *SCpnt, void (*done)(struct scsi_cmnd *))
{
        int i;
        int port_base = SCpnt->device->host->io_port;
        struct sym53c500_data *data =
            (struct sym53c500_data *)SCpnt->device->host->hostdata;

        VDEB(printk("SYM53C500_queue called\n"));

        DEB(printk("cmd=%02x, cmd_len=%02x, target=%02x, lun=%02x, bufflen=%d\n", 
            SCpnt->cmnd[0], SCpnt->cmd_len, SCpnt->device->id, 
                   (u8)SCpnt->device->lun,  scsi_bufflen(SCpnt)));

        VDEB(for (i = 0; i < SCpnt->cmd_len; i++)
            printk("cmd[%d]=%02x  ", i, SCpnt->cmnd[i]));
        VDEB(printk("\n"));

        data->current_SC = SCpnt;
        data->current_SC->scsi_done = done;
        data->current_SC->SCp.phase = command_ph;
        data->current_SC->SCp.Status = 0;
        data->current_SC->SCp.Message = 0;

        /* We are locked here already by the mid layer */
        REG0(port_base);
        outb(scmd_id(SCpnt), port_base + DEST_ID);      /* set destination */
        outb(FLUSH_FIFO, port_base + CMD_REG);  /* reset the fifos */

        for (i = 0; i < SCpnt->cmd_len; i++) {
                outb(SCpnt->cmnd[i], port_base + SCSI_FIFO);
        }
        outb(SELECT_NO_ATN, port_base + CMD_REG);

        return 0;
}

static DEF_SCSI_QCMD(SYM53C500_queue)

static int 
SYM53C500_host_reset(struct scsi_cmnd *SCpnt)
{
        int port_base = SCpnt->device->host->io_port;

        DEB(printk("SYM53C500_host_reset called\n"));
        spin_lock_irq(SCpnt->device->host->host_lock);
        SYM53C500_int_host_reset(port_base);
        spin_unlock_irq(SCpnt->device->host->host_lock);

        return SUCCESS;
}

static int 
SYM53C500_biosparm(struct scsi_device *disk,
    struct block_device *dev,
    sector_t capacity, int *info_array)
{
        int size;

        DEB(printk("SYM53C500_biosparm called\n"));

        size = capacity;
        info_array[0] = 64;             /* heads */
        info_array[1] = 32;             /* sectors */
        info_array[2] = size >> 11;     /* cylinders */
        if (info_array[2] > 1024) {     /* big disk */
                info_array[0] = 255;
                info_array[1] = 63;
                info_array[2] = size / (255 * 63);
        }
        return 0;
}

static ssize_t
SYM53C500_show_pio(struct device *dev, struct device_attribute *attr,
                   char *buf)
{
        struct Scsi_Host *SHp = class_to_shost(dev);
        struct sym53c500_data *data =
            (struct sym53c500_data *)SHp->hostdata;

        return snprintf(buf, 4, "%d\n", data->fast_pio);
}

static ssize_t
SYM53C500_store_pio(struct device *dev, struct device_attribute *attr,
                    const char *buf, size_t count)
{
        int pio;
        struct Scsi_Host *SHp = class_to_shost(dev);
        struct sym53c500_data *data =
            (struct sym53c500_data *)SHp->hostdata;

        pio = simple_strtoul(buf, NULL, 0);
        if (pio == 0 || pio == 1) {
                data->fast_pio = pio;
                return count;
        }
        else
                return -EINVAL;
}

/*
*  SCSI HBA device attributes we want to
*  make available via sysfs.
*/
static struct device_attribute SYM53C500_pio_attr = {
        .attr = {
                .name = "fast_pio",
                .mode = (S_IRUGO | S_IWUSR),
        },
        .show = SYM53C500_show_pio,
        .store = SYM53C500_store_pio,
};

static struct device_attribute *SYM53C500_shost_attrs[] = {
        &SYM53C500_pio_attr,
        NULL,
};

/*
*  scsi_host_template initializer
*/
static struct scsi_host_template sym53c500_driver_template = {
     .module                    = THIS_MODULE,
     .name                      = "SYM53C500",
     .info                      = SYM53C500_info,
     .queuecommand              = SYM53C500_queue,
     .eh_host_reset_handler     = SYM53C500_host_reset,
     .bios_param                = SYM53C500_biosparm,
     .proc_name                 = "SYM53C500",
     .can_queue                 = 1,
     .this_id                   = 7,
     .sg_tablesize              = 32,
     .use_clustering            = ENABLE_CLUSTERING,
     .shost_attrs               = SYM53C500_shost_attrs
};

static int SYM53C500_config_check(struct pcmcia_device *p_dev, void *priv_data)
{
        p_dev->io_lines = 10;
        p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
        p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;

        if (p_dev->resource[0]->start == 0)
                return -ENODEV;

        return pcmcia_request_io(p_dev);
}

static int
SYM53C500_config(struct pcmcia_device *link)
{
        struct scsi_info_t *info = link->priv;
        int ret;
        int irq_level, port_base;
        struct Scsi_Host *host;
        struct scsi_host_template *tpnt = &sym53c500_driver_template;
        struct sym53c500_data *data;

        dev_dbg(&link->dev, "SYM53C500_config\n");

        info->manf_id = link->manf_id;

        ret = pcmcia_loop_config(link, SYM53C500_config_check, NULL);
        if (ret)
                goto failed;

        if (!link->irq)
                goto failed;

        ret = pcmcia_enable_device(link);
        if (ret)
                goto failed;

        /*
        *  That's the trouble with copying liberally from another driver.
        *  Some things probably aren't relevant, and I suspect this entire
        *  section dealing with manufacturer IDs can be scrapped.       --rct
        */
        if ((info->manf_id == MANFID_MACNICA) ||
            (info->manf_id == MANFID_PIONEER) ||
            (info->manf_id == 0x0098)) {
                /* set ATAcmd */
                outb(0xb4, link->resource[0]->start + 0xd);
                outb(0x24, link->resource[0]->start + 0x9);
                outb(0x04, link->resource[0]->start + 0xd);
        }

        /*
        *  irq_level == 0 implies tpnt->can_queue == 0, which
        *  is not supported in 2.6.  Thus, only irq_level > 0
        *  will be allowed.
        *
        *  Possible port_base values are as follows:
        *
        *       0x130, 0x230, 0x280, 0x290,
        *       0x320, 0x330, 0x340, 0x350
        */
        port_base = link->resource[0]->start;
        irq_level = link->irq;

        DEB(printk("SYM53C500: port_base=0x%x, irq=%d, fast_pio=%d\n",
            port_base, irq_level, USE_FAST_PIO);)

        chip_init(port_base);

        host = scsi_host_alloc(tpnt, sizeof(struct sym53c500_data));
        if (!host) {
                printk("SYM53C500: Unable to register host, giving up.\n");
                goto err_release;
        }

        data = (struct sym53c500_data *)host->hostdata;

        if (irq_level > 0) {
                if (request_irq(irq_level, SYM53C500_intr, IRQF_SHARED, "SYM53C500", host)) {
                        printk("SYM53C500: unable to allocate IRQ %d\n", irq_level);
                        goto err_free_scsi;
                }
                DEB(printk("SYM53C500: allocated IRQ %d\n", irq_level));
        } else if (irq_level == 0) {
                DEB(printk("SYM53C500: No interrupts detected\n"));
                goto err_free_scsi;
        } else {
                DEB(printk("SYM53C500: Shouldn't get here!\n"));
                goto err_free_scsi;
        }

        host->unique_id = port_base;
        host->irq = irq_level;
        host->io_port = port_base;
        host->n_io_port = 0x10;
        host->dma_channel = -1;

        /*
        *  Note fast_pio is set to USE_FAST_PIO by
        *  default, but can be changed via "sysfs".
        */
        data->fast_pio = USE_FAST_PIO;

        info->host = host;

        if (scsi_add_host(host, NULL))
                goto err_free_irq;

        scsi_scan_host(host);

        return 0;

err_free_irq:
        free_irq(irq_level, host);
err_free_scsi:
        scsi_host_put(host);
err_release:
        release_region(port_base, 0x10);
        printk(KERN_INFO "sym53c500_cs: no SCSI devices found\n");
        return -ENODEV;

failed:
        SYM53C500_release(link);
        return -ENODEV;
} /* SYM53C500_config */

static int sym53c500_resume(struct pcmcia_device *link)
{
        struct scsi_info_t *info = link->priv;

        /* See earlier comment about manufacturer IDs. */
        if ((info->manf_id == MANFID_MACNICA) ||
            (info->manf_id == MANFID_PIONEER) ||
            (info->manf_id == 0x0098)) {
                outb(0x80, link->resource[0]->start + 0xd);
                outb(0x24, link->resource[0]->start + 0x9);
                outb(0x04, link->resource[0]->start + 0xd);
        }
        /*
         *  If things don't work after a "resume",
         *  this is a good place to start looking.
         */
        SYM53C500_int_host_reset(link->resource[0]->start);

        return 0;
}

static void
SYM53C500_detach(struct pcmcia_device *link)
{
        dev_dbg(&link->dev, "SYM53C500_detach\n");

        SYM53C500_release(link);

        kfree(link->priv);
        link->priv = NULL;
} /* SYM53C500_detach */

static int
SYM53C500_probe(struct pcmcia_device *link)
{
        struct scsi_info_t *info;

        dev_dbg(&link->dev, "SYM53C500_attach()\n");

        /* Create new SCSI device */
        info = kzalloc(sizeof(*info), GFP_KERNEL);
        if (!info)
                return -ENOMEM;
        info->p_dev = link;
        link->priv = info;
        link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO;

        return SYM53C500_config(link);
} /* SYM53C500_attach */

MODULE_AUTHOR("Bob Tracy <rct@frus.com>");
MODULE_DESCRIPTION("SYM53C500 PCMCIA SCSI driver");
MODULE_LICENSE("GPL");

static const struct pcmcia_device_id sym53c500_ids[] = {
        PCMCIA_DEVICE_PROD_ID12("BASICS by New Media Corporation", "SCSI Sym53C500", 0x23c78a9d, 0x0099e7f7),
        PCMCIA_DEVICE_PROD_ID12("New Media Corporation", "SCSI Bus Toaster Sym53C500", 0x085a850b, 0x45432eb8),
        PCMCIA_DEVICE_PROD_ID2("SCSI9000", 0x21648f44),
        PCMCIA_DEVICE_NULL,
};
MODULE_DEVICE_TABLE(pcmcia, sym53c500_ids);

static struct pcmcia_driver sym53c500_cs_driver = {
        .owner          = THIS_MODULE,
        .name           = "sym53c500_cs",
        .probe          = SYM53C500_probe,
        .remove         = SYM53C500_detach,
        .id_table       = sym53c500_ids,
        .resume         = sym53c500_resume,
};

static int __init
init_sym53c500_cs(void)
{
        return pcmcia_register_driver(&sym53c500_cs_driver);
}

static void __exit
exit_sym53c500_cs(void)
{
        pcmcia_unregister_driver(&sym53c500_cs_driver);
}

module_init(init_sym53c500_cs);
module_exit(exit_sym53c500_cs);