1
2
3
4
5
6
7
8
9
10
11
12#include <linux/kernel.h>
13#include <linux/init.h>
14#include <linux/device.h>
15#include <linux/serial.h>
16#include <linux/tty.h>
17#include <linux/serial_8250.h>
18#include <linux/gpio/machine.h>
19#include <linux/io.h>
20#include <linux/mtd/mtd.h>
21#include <linux/mtd/rawnand.h>
22#include <linux/mtd/partitions.h>
23#include <linux/mtd/platnand.h>
24#include <linux/delay.h>
25#include <linux/gpio.h>
26#include <asm/types.h>
27#include <asm/setup.h>
28#include <asm/memory.h>
29#include <mach/hardware.h>
30#include <asm/mach-types.h>
31#include <asm/irq.h>
32#include <asm/mach/arch.h>
33#include <asm/mach/flash.h>
34
35#include "irqs.h"
36
37#define IXDP425_SDA_PIN 7
38#define IXDP425_SCL_PIN 6
39
40
41#define IXDP425_NAND_NCE_PIN 12
42
43#define IXDP425_NAND_CMD_BYTE 0x01
44#define IXDP425_NAND_ADDR_BYTE 0x02
45
46static struct flash_platform_data ixdp425_flash_data = {
47 .map_name = "cfi_probe",
48 .width = 2,
49};
50
51static struct resource ixdp425_flash_resource = {
52 .flags = IORESOURCE_MEM,
53};
54
55static struct platform_device ixdp425_flash = {
56 .name = "IXP4XX-Flash",
57 .id = 0,
58 .dev = {
59 .platform_data = &ixdp425_flash_data,
60 },
61 .num_resources = 1,
62 .resource = &ixdp425_flash_resource,
63};
64
65#if defined(CONFIG_MTD_NAND_PLATFORM) || \
66 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
67
68static struct mtd_partition ixdp425_partitions[] = {
69 {
70 .name = "ixp400 NAND FS 0",
71 .offset = 0,
72 .size = SZ_8M
73 }, {
74 .name = "ixp400 NAND FS 1",
75 .offset = MTDPART_OFS_APPEND,
76 .size = MTDPART_SIZ_FULL
77 },
78};
79
80static void
81ixdp425_flash_nand_cmd_ctrl(struct nand_chip *this, int cmd, unsigned int ctrl)
82{
83 int offset = (int)nand_get_controller_data(this);
84
85 if (ctrl & NAND_CTRL_CHANGE) {
86 if (ctrl & NAND_NCE) {
87 gpio_set_value(IXDP425_NAND_NCE_PIN, 0);
88 udelay(5);
89 } else
90 gpio_set_value(IXDP425_NAND_NCE_PIN, 1);
91
92 offset = (ctrl & NAND_CLE) ? IXDP425_NAND_CMD_BYTE : 0;
93 offset |= (ctrl & NAND_ALE) ? IXDP425_NAND_ADDR_BYTE : 0;
94 nand_set_controller_data(this, (void *)offset);
95 }
96
97 if (cmd != NAND_CMD_NONE)
98 writeb(cmd, this->legacy.IO_ADDR_W + offset);
99}
100
101static struct platform_nand_data ixdp425_flash_nand_data = {
102 .chip = {
103 .nr_chips = 1,
104 .chip_delay = 30,
105 .partitions = ixdp425_partitions,
106 .nr_partitions = ARRAY_SIZE(ixdp425_partitions),
107 },
108 .ctrl = {
109 .cmd_ctrl = ixdp425_flash_nand_cmd_ctrl
110 }
111};
112
113static struct resource ixdp425_flash_nand_resource = {
114 .flags = IORESOURCE_MEM,
115};
116
117static struct platform_device ixdp425_flash_nand = {
118 .name = "gen_nand",
119 .id = -1,
120 .dev = {
121 .platform_data = &ixdp425_flash_nand_data,
122 },
123 .num_resources = 1,
124 .resource = &ixdp425_flash_nand_resource,
125};
126#endif
127
128static struct gpiod_lookup_table ixdp425_i2c_gpiod_table = {
129 .dev_id = "i2c-gpio.0",
130 .table = {
131 GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", IXDP425_SDA_PIN,
132 NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
133 GPIO_LOOKUP_IDX("IXP4XX_GPIO_CHIP", IXDP425_SCL_PIN,
134 NULL, 1, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
135 },
136};
137
138static struct platform_device ixdp425_i2c_gpio = {
139 .name = "i2c-gpio",
140 .id = 0,
141 .dev = {
142 .platform_data = NULL,
143 },
144};
145
146static struct resource ixdp425_uart_resources[] = {
147 {
148 .start = IXP4XX_UART1_BASE_PHYS,
149 .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
150 .flags = IORESOURCE_MEM
151 },
152 {
153 .start = IXP4XX_UART2_BASE_PHYS,
154 .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
155 .flags = IORESOURCE_MEM
156 }
157};
158
159static struct plat_serial8250_port ixdp425_uart_data[] = {
160 {
161 .mapbase = IXP4XX_UART1_BASE_PHYS,
162 .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
163 .irq = IRQ_IXP4XX_UART1,
164 .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
165 .iotype = UPIO_MEM,
166 .regshift = 2,
167 .uartclk = IXP4XX_UART_XTAL,
168 },
169 {
170 .mapbase = IXP4XX_UART2_BASE_PHYS,
171 .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
172 .irq = IRQ_IXP4XX_UART2,
173 .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
174 .iotype = UPIO_MEM,
175 .regshift = 2,
176 .uartclk = IXP4XX_UART_XTAL,
177 },
178 { },
179};
180
181static struct platform_device ixdp425_uart = {
182 .name = "serial8250",
183 .id = PLAT8250_DEV_PLATFORM,
184 .dev.platform_data = ixdp425_uart_data,
185 .num_resources = 2,
186 .resource = ixdp425_uart_resources
187};
188
189
190static struct resource ixp425_npeb_resources[] = {
191 {
192 .start = IXP4XX_EthB_BASE_PHYS,
193 .end = IXP4XX_EthB_BASE_PHYS + 0x0fff,
194 .flags = IORESOURCE_MEM,
195 },
196};
197
198static struct resource ixp425_npec_resources[] = {
199 {
200 .start = IXP4XX_EthC_BASE_PHYS,
201 .end = IXP4XX_EthC_BASE_PHYS + 0x0fff,
202 .flags = IORESOURCE_MEM,
203 },
204};
205
206static struct eth_plat_info ixdp425_plat_eth[] = {
207 {
208 .phy = 0,
209 .rxq = 3,
210 .txreadyq = 20,
211 }, {
212 .phy = 1,
213 .rxq = 4,
214 .txreadyq = 21,
215 }
216};
217
218static struct platform_device ixdp425_eth[] = {
219 {
220 .name = "ixp4xx_eth",
221 .id = IXP4XX_ETH_NPEB,
222 .dev.platform_data = ixdp425_plat_eth,
223 .num_resources = ARRAY_SIZE(ixp425_npeb_resources),
224 .resource = ixp425_npeb_resources,
225 }, {
226 .name = "ixp4xx_eth",
227 .id = IXP4XX_ETH_NPEC,
228 .dev.platform_data = ixdp425_plat_eth + 1,
229 .num_resources = ARRAY_SIZE(ixp425_npec_resources),
230 .resource = ixp425_npec_resources,
231 }
232};
233
234static struct platform_device *ixdp425_devices[] __initdata = {
235 &ixdp425_i2c_gpio,
236 &ixdp425_flash,
237#if defined(CONFIG_MTD_NAND_PLATFORM) || \
238 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
239 &ixdp425_flash_nand,
240#endif
241 &ixdp425_uart,
242 &ixdp425_eth[0],
243 &ixdp425_eth[1],
244};
245
246static void __init ixdp425_init(void)
247{
248 ixp4xx_sys_init();
249
250 ixdp425_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
251 ixdp425_flash_resource.end =
252 IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
253
254#if defined(CONFIG_MTD_NAND_PLATFORM) || \
255 defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
256 ixdp425_flash_nand_resource.start = IXP4XX_EXP_BUS_BASE(3),
257 ixdp425_flash_nand_resource.end = IXP4XX_EXP_BUS_BASE(3) + 0x10 - 1;
258
259 gpio_request(IXDP425_NAND_NCE_PIN, "NAND NCE pin");
260 gpio_direction_output(IXDP425_NAND_NCE_PIN, 0);
261
262
263 *IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN |
264 IXP4XX_EXP_BUS_STROBE_T(1) |
265 IXP4XX_EXP_BUS_CYCLES(0) |
266 IXP4XX_EXP_BUS_SIZE(0) |
267 IXP4XX_EXP_BUS_WR_EN |
268 IXP4XX_EXP_BUS_BYTE_EN;
269#endif
270
271 if (cpu_is_ixp43x()) {
272 ixdp425_uart.num_resources = 1;
273 ixdp425_uart_data[1].flags = 0;
274 }
275
276 gpiod_add_lookup_table(&ixdp425_i2c_gpiod_table);
277 platform_add_devices(ixdp425_devices, ARRAY_SIZE(ixdp425_devices));
278}
279
280#ifdef CONFIG_ARCH_IXDP425
281MACHINE_START(IXDP425, "Intel IXDP425 Development Platform")
282
283 .map_io = ixp4xx_map_io,
284 .init_early = ixp4xx_init_early,
285 .init_irq = ixp4xx_init_irq,
286 .init_time = ixp4xx_timer_init,
287 .atag_offset = 0x100,
288 .init_machine = ixdp425_init,
289#if defined(CONFIG_PCI)
290 .dma_zone_size = SZ_64M,
291#endif
292 .restart = ixp4xx_restart,
293MACHINE_END
294#endif
295
296#ifdef CONFIG_MACH_IXDP465
297MACHINE_START(IXDP465, "Intel IXDP465 Development Platform")
298
299 .map_io = ixp4xx_map_io,
300 .init_early = ixp4xx_init_early,
301 .init_irq = ixp4xx_init_irq,
302 .init_time = ixp4xx_timer_init,
303 .atag_offset = 0x100,
304 .init_machine = ixdp425_init,
305#if defined(CONFIG_PCI)
306 .dma_zone_size = SZ_64M,
307#endif
308MACHINE_END
309#endif
310
311#ifdef CONFIG_ARCH_PRPMC1100
312MACHINE_START(IXCDP1100, "Intel IXCDP1100 Development Platform")
313
314 .map_io = ixp4xx_map_io,
315 .init_early = ixp4xx_init_early,
316 .init_irq = ixp4xx_init_irq,
317 .init_time = ixp4xx_timer_init,
318 .atag_offset = 0x100,
319 .init_machine = ixdp425_init,
320#if defined(CONFIG_PCI)
321 .dma_zone_size = SZ_64M,
322#endif
323MACHINE_END
324#endif
325
326#ifdef CONFIG_MACH_KIXRP435
327MACHINE_START(KIXRP435, "Intel KIXRP435 Reference Platform")
328
329 .map_io = ixp4xx_map_io,
330 .init_early = ixp4xx_init_early,
331 .init_irq = ixp4xx_init_irq,
332 .init_time = ixp4xx_timer_init,
333 .atag_offset = 0x100,
334 .init_machine = ixdp425_init,
335#if defined(CONFIG_PCI)
336 .dma_zone_size = SZ_64M,
337#endif
338MACHINE_END
339#endif
340
