// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Support for the Tundra TSI148 VME-PCI Bridge Chip
 *
 * Author: Martyn Welch <martyn.welch@ge.com>
 * Copyright 2008 GE Intelligent Platforms Embedded Systems, Inc.
 *
 * Based on work by Tom Armistead and Ajit Prem
 * Copyright 2004 Motorola Inc.
 */

#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/mm.h>
#include <linux/types.h>
#include <linux/errno.h>
#include <linux/proc_fs.h>
#include <linux/pci.h>
#include <linux/poll.h>
#include <linux/dma-mapping.h>
#include <linux/interrupt.h>
#include <linux/spinlock.h>
#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/time.h>
#include <linux/io.h>
#include <linux/uaccess.h>
#include <linux/byteorder/generic.h>
#include <linux/vme.h>

#include "../vme_bridge.h"
#include "vme_tsi148.h"

static int tsi148_probe(struct pci_dev *, const struct pci_device_id *);
static void tsi148_remove(struct pci_dev *);


/* Module parameter */
static bool err_chk;
static int geoid;

static const char driver_name[] = "vme_tsi148";

static const struct pci_device_id tsi148_ids[] = {
        { PCI_DEVICE(PCI_VENDOR_ID_TUNDRA, PCI_DEVICE_ID_TUNDRA_TSI148) },
        { },
};

MODULE_DEVICE_TABLE(pci, tsi148_ids);

static struct pci_driver tsi148_driver = {
        .name = driver_name,
        .id_table = tsi148_ids,
        .probe = tsi148_probe,
        .remove = tsi148_remove,
};

static void reg_join(unsigned int high, unsigned int low,
        unsigned long long *variable)
{
        *variable = (unsigned long long)high << 32;
        *variable |= (unsigned long long)low;
}

static void reg_split(unsigned long long variable, unsigned int *high,
        unsigned int *low)
{
        *low = (unsigned int)variable & 0xFFFFFFFF;
        *high = (unsigned int)(variable >> 32);
}

/*
 * Wakes up DMA queue.
 */
static u32 tsi148_DMA_irqhandler(struct tsi148_driver *bridge,
        int channel_mask)
{
        u32 serviced = 0;

        if (channel_mask & TSI148_LCSR_INTS_DMA0S) {
                wake_up(&bridge->dma_queue[0]);
                serviced |= TSI148_LCSR_INTC_DMA0C;
        }
        if (channel_mask & TSI148_LCSR_INTS_DMA1S) {
                wake_up(&bridge->dma_queue[1]);
                serviced |= TSI148_LCSR_INTC_DMA1C;
        }

        return serviced;
}

/*
 * Wake up location monitor queue
 */
static u32 tsi148_LM_irqhandler(struct tsi148_driver *bridge, u32 stat)
{
        int i;
        u32 serviced = 0;

        for (i = 0; i < 4; i++) {
                if (stat & TSI148_LCSR_INTS_LMS[i]) {
                        /* We only enable interrupts if the callback is set */
                        bridge->lm_callback[i](bridge->lm_data[i]);
                        serviced |= TSI148_LCSR_INTC_LMC[i];
                }
        }

        return serviced;
}

/*
 * Wake up mail box queue.
 *
 * XXX This functionality is not exposed up though API.
 */
static u32 tsi148_MB_irqhandler(struct vme_bridge *tsi148_bridge, u32 stat)
{
        int i;
        u32 val;
        u32 serviced = 0;
        struct tsi148_driver *bridge;

        bridge = tsi148_bridge->driver_priv;

        for (i = 0; i < 4; i++) {
                if (stat & TSI148_LCSR_INTS_MBS[i]) {
                        val = ioread32be(bridge->base + TSI148_GCSR_MBOX[i]);
                        dev_err(tsi148_bridge->parent, "VME Mailbox %d received"
                                ": 0x%x\n", i, val);
                        serviced |= TSI148_LCSR_INTC_MBC[i];
                }
        }

        return serviced;
}

/*
 * Display error & status message when PERR (PCI) exception interrupt occurs.
 */
static u32 tsi148_PERR_irqhandler(struct vme_bridge *tsi148_bridge)
{
        struct tsi148_driver *bridge;

        bridge = tsi148_bridge->driver_priv;

        dev_err(tsi148_bridge->parent, "PCI Exception at address: 0x%08x:%08x, "
                "attributes: %08x\n",
                ioread32be(bridge->base + TSI148_LCSR_EDPAU),
                ioread32be(bridge->base + TSI148_LCSR_EDPAL),
                ioread32be(bridge->base + TSI148_LCSR_EDPAT));

        dev_err(tsi148_bridge->parent, "PCI-X attribute reg: %08x, PCI-X split "
                "completion reg: %08x\n",
                ioread32be(bridge->base + TSI148_LCSR_EDPXA),
                ioread32be(bridge->base + TSI148_LCSR_EDPXS));

        iowrite32be(TSI148_LCSR_EDPAT_EDPCL, bridge->base + TSI148_LCSR_EDPAT);

        return TSI148_LCSR_INTC_PERRC;
}

/*
 * Save address and status when VME error interrupt occurs.
 */
static u32 tsi148_VERR_irqhandler(struct vme_bridge *tsi148_bridge)
{
        unsigned int error_addr_high, error_addr_low;
        unsigned long long error_addr;
        u32 error_attrib;
        int error_am;
        struct tsi148_driver *bridge;

        bridge = tsi148_bridge->driver_priv;

        error_addr_high = ioread32be(bridge->base + TSI148_LCSR_VEAU);
        error_addr_low = ioread32be(bridge->base + TSI148_LCSR_VEAL);
        error_attrib = ioread32be(bridge->base + TSI148_LCSR_VEAT);
        error_am = (error_attrib & TSI148_LCSR_VEAT_AM_M) >> 8;

        reg_join(error_addr_high, error_addr_low, &error_addr);

        /* Check for exception register overflow (we have lost error data) */
        if (error_attrib & TSI148_LCSR_VEAT_VEOF) {
                dev_err(tsi148_bridge->parent, "VME Bus Exception Overflow "
                        "Occurred\n");
        }

        if (err_chk)
                vme_bus_error_handler(tsi148_bridge, error_addr, error_am);
        else
                dev_err(tsi148_bridge->parent,
                        "VME Bus Error at address: 0x%llx, attributes: %08x\n",
                        error_addr, error_attrib);

        /* Clear Status */
        iowrite32be(TSI148_LCSR_VEAT_VESCL, bridge->base + TSI148_LCSR_VEAT);

        return TSI148_LCSR_INTC_VERRC;
}

/*
 * Wake up IACK queue.
 */
static u32 tsi148_IACK_irqhandler(struct tsi148_driver *bridge)
{
        wake_up(&bridge->iack_queue);

        return TSI148_LCSR_INTC_IACKC;
}

/*
 * Calling VME bus interrupt callback if provided.
 */
static u32 tsi148_VIRQ_irqhandler(struct vme_bridge *tsi148_bridge,
        u32 stat)
{
        int vec, i, serviced = 0;
        struct tsi148_driver *bridge;

        bridge = tsi148_bridge->driver_priv;

        for (i = 7; i > 0; i--) {
                if (stat & (1 << i)) {
                        /*
                         * Note: Even though the registers are defined as
                         * 32-bits in the spec, we only want to issue 8-bit
                         * IACK cycles on the bus, read from offset 3.
                         */
                        vec = ioread8(bridge->base + TSI148_LCSR_VIACK[i] + 3);

                        vme_irq_handler(tsi148_bridge, i, vec);

                        serviced |= (1 << i);
                }
        }

        return serviced;
}

/*
 * Top level interrupt handler.  Clears appropriate interrupt status bits and
 * then calls appropriate sub handler(s).
 */
static irqreturn_t tsi148_irqhandler(int irq, void *ptr)
{
        u32 stat, enable, serviced = 0;
        struct vme_bridge *tsi148_bridge;
        struct tsi148_driver *bridge;

        tsi148_bridge = ptr;

        bridge = tsi148_bridge->driver_priv;

        /* Determine which interrupts are unmasked and set */
        enable = ioread32be(bridge->base + TSI148_LCSR_INTEO);
        stat = ioread32be(bridge->base + TSI148_LCSR_INTS);

        /* Only look at unmasked interrupts */
        stat &= enable;

        if (unlikely(!stat))
                return IRQ_NONE;

        /* Call subhandlers as appropriate */
        /* DMA irqs */
        if (stat & (TSI148_LCSR_INTS_DMA1S | TSI148_LCSR_INTS_DMA0S))
                serviced |= tsi148_DMA_irqhandler(bridge, stat);

        /* Location monitor irqs */
        if (stat & (TSI148_LCSR_INTS_LM3S | TSI148_LCSR_INTS_LM2S |
                        TSI148_LCSR_INTS_LM1S | TSI148_LCSR_INTS_LM0S))
                serviced |= tsi148_LM_irqhandler(bridge, stat);

        /* Mail box irqs */
        if (stat & (TSI148_LCSR_INTS_MB3S | TSI148_LCSR_INTS_MB2S |
                        TSI148_LCSR_INTS_MB1S | TSI148_LCSR_INTS_MB0S))
                serviced |= tsi148_MB_irqhandler(tsi148_bridge, stat);

        /* PCI bus error */
        if (stat & TSI148_LCSR_INTS_PERRS)
                serviced |= tsi148_PERR_irqhandler(tsi148_bridge);

        /* VME bus error */
        if (stat & TSI148_LCSR_INTS_VERRS)
                serviced |= tsi148_VERR_irqhandler(tsi148_bridge);

        /* IACK irq */
        if (stat & TSI148_LCSR_INTS_IACKS)
                serviced |= tsi148_IACK_irqhandler(bridge);

        /* VME bus irqs */
        if (stat & (TSI148_LCSR_INTS_IRQ7S | TSI148_LCSR_INTS_IRQ6S |
                        TSI148_LCSR_INTS_IRQ5S | TSI148_LCSR_INTS_IRQ4S |
                        TSI148_LCSR_INTS_IRQ3S | TSI148_LCSR_INTS_IRQ2S |
                        TSI148_LCSR_INTS_IRQ1S))
                serviced |= tsi148_VIRQ_irqhandler(tsi148_bridge, stat);

        /* Clear serviced interrupts */
        iowrite32be(serviced, bridge->base + TSI148_LCSR_INTC);

        return IRQ_HANDLED;
}

static int tsi148_irq_init(struct vme_bridge *tsi148_bridge)
{
        int result;
        unsigned int tmp;
        struct pci_dev *pdev;
        struct tsi148_driver *bridge;

        pdev = to_pci_dev(tsi148_bridge->parent);

        bridge = tsi148_bridge->driver_priv;

        result = request_irq(pdev->irq,
                             tsi148_irqhandler,
                             IRQF_SHARED,
                             driver_name, tsi148_bridge);
        if (result) {
                dev_err(tsi148_bridge->parent, "Can't get assigned pci irq "
                        "vector %02X\n", pdev->irq);
                return result;
        }

        /* Enable and unmask interrupts */
        tmp = TSI148_LCSR_INTEO_DMA1EO | TSI148_LCSR_INTEO_DMA0EO |
                TSI148_LCSR_INTEO_MB3EO | TSI148_LCSR_INTEO_MB2EO |
                TSI148_LCSR_INTEO_MB1EO | TSI148_LCSR_INTEO_MB0EO |
                TSI148_LCSR_INTEO_PERREO | TSI148_LCSR_INTEO_VERREO |
                TSI148_LCSR_INTEO_IACKEO;

        /* This leaves the following interrupts masked.
         * TSI148_LCSR_INTEO_VIEEO
         * TSI148_LCSR_INTEO_SYSFLEO
         * TSI148_LCSR_INTEO_ACFLEO
         */

        /* Don't enable Location Monitor interrupts here - they will be
         * enabled when the location monitors are properly configured and
         * a callback has been attached.
         * TSI148_LCSR_INTEO_LM0EO
         * TSI148_LCSR_INTEO_LM1EO
         * TSI148_LCSR_INTEO_LM2EO
         * TSI148_LCSR_INTEO_LM3EO
         */

        /* Don't enable VME interrupts until we add a handler, else the board
         * will respond to it and we don't want that unless it knows how to
         * properly deal with it.
         * TSI148_LCSR_INTEO_IRQ7EO
         * TSI148_LCSR_INTEO_IRQ6EO
         * TSI148_LCSR_INTEO_IRQ5EO
         * TSI148_LCSR_INTEO_IRQ4EO
         * TSI148_LCSR_INTEO_IRQ3EO
         * TSI148_LCSR_INTEO_IRQ2EO
         * TSI148_LCSR_INTEO_IRQ1EO
         */

        iowrite32be(tmp, bridge->base + TSI148_LCSR_INTEO);
        iowrite32be(tmp, bridge->base + TSI148_LCSR_INTEN);

        return 0;
}

static void tsi148_irq_exit(struct vme_bridge *tsi148_bridge,
        struct pci_dev *pdev)
{
        struct tsi148_driver *bridge = tsi148_bridge->driver_priv;

        /* Turn off interrupts */
        iowrite32be(0x0, bridge->base + TSI148_LCSR_INTEO);
        iowrite32be(0x0, bridge->base + TSI148_LCSR_INTEN);

        /* Clear all interrupts */
        iowrite32be(0xFFFFFFFF, bridge->base + TSI148_LCSR_INTC);

        /* Detach interrupt handler */
        free_irq(pdev->irq, tsi148_bridge);
}

/*
 * Check to see if an IACk has been received, return true (1) or false (0).
 */
static int tsi148_iack_received(struct tsi148_driver *bridge)
{
        u32 tmp;

        tmp = ioread32be(bridge->base + TSI148_LCSR_VICR);

        if (tmp & TSI148_LCSR_VICR_IRQS)
                return 0;
        else
                return 1;
}

/*
 * Configure VME interrupt
 */
static void tsi148_irq_set(struct vme_bridge *tsi148_bridge, int level,
        int state, int sync)
{
        struct pci_dev *pdev;
        u32 tmp;
        struct tsi148_driver *bridge;

        bridge = tsi148_bridge->driver_priv;

        /* We need to do the ordering differently for enabling and disabling */
        if (state == 0) {
                tmp = ioread32be(bridge->base + TSI148_LCSR_INTEN);
                tmp &= ~TSI148_LCSR_INTEN_IRQEN[level - 1];
                iowrite32be(tmp, bridge->base + TSI148_LCSR_INTEN);

                tmp = ioread32be(bridge->base + TSI148_LCSR_INTEO);
                tmp &= ~TSI148_LCSR_INTEO_IRQEO[level - 1];
                iowrite32be(tmp, bridge->base + TSI148_LCSR_INTEO);

                if (sync != 0) {
                        pdev = to_pci_dev(tsi148_bridge->parent);
                        synchronize_irq(pdev->irq);
                }
        } else {
                tmp = ioread32be(bridge->base + TSI148_LCSR_INTEO);
                tmp |= TSI148_LCSR_INTEO_IRQEO[level - 1];
                iowrite32be(tmp, bridge->base + TSI148_LCSR_INTEO);

                tmp = ioread32be(bridge->base + TSI148_LCSR_INTEN);
                tmp |= TSI148_LCSR_INTEN_IRQEN[level - 1];
                iowrite32be(tmp, bridge->base + TSI148_LCSR_INTEN);
        }
}

/*
 * Generate a VME bus interrupt at the requested level & vector. Wait for
 * interrupt to be acked.
 */
static int tsi148_irq_generate(struct vme_bridge *tsi148_bridge, int level,
        int statid)
{
        u32 tmp;
        struct tsi148_driver *bridge;

        bridge = tsi148_bridge->driver_priv;

        mutex_lock(&bridge->vme_int);

        /* Read VICR register */
        tmp = ioread32be(bridge->base + TSI148_LCSR_VICR);

        /* Set Status/ID */
        tmp = (tmp & ~TSI148_LCSR_VICR_STID_M) |
                (statid & TSI148_LCSR_VICR_STID_M);
        iowrite32be(tmp, bridge->base + TSI148_LCSR_VICR);

        /* Assert VMEbus IRQ */
        tmp = tmp | TSI148_LCSR_VICR_IRQL[level];
        iowrite32be(tmp, bridge->base + TSI148_LCSR_VICR);

        /* XXX Consider implementing a timeout? */
        wait_event_interruptible(bridge->iack_queue,
                tsi148_iack_received(bridge));

        mutex_unlock(&bridge->vme_int);

        return 0;
}

/*
 * Initialize a slave window with the requested attributes.
 */
static int tsi148_slave_set(struct vme_slave_resource *image, int enabled,
        unsigned long long vme_base, unsigned long long size,
        dma_addr_t pci_base, u32 aspace, u32 cycle)
{
        unsigned int i, addr = 0, granularity = 0;
        unsigned int temp_ctl = 0;
        unsigned int vme_base_low, vme_base_high;
        unsigned int vme_bound_low, vme_bound_high;
        unsigned int pci_offset_low, pci_offset_high;
        unsigned long long vme_bound, pci_offset;
        struct vme_bridge *tsi148_bridge;
        struct tsi148_driver *bridge;

        tsi148_bridge = image->parent;
        bridge = tsi148_bridge->driver_priv;

        i = image->number;

        switch (aspace) {
        case VME_A16:
                granularity = 0x10;
                addr |= TSI148_LCSR_ITAT_AS_A16;
                break;
        case VME_A24:
                granularity = 0x1000;
                addr |= TSI148_LCSR_ITAT_AS_A24;
                break;
        case VME_A32:
                granularity = 0x10000;
                addr |= TSI148_LCSR_ITAT_AS_A32;
                break;
        case VME_A64:
                granularity = 0x10000;
                addr |= TSI148_LCSR_ITAT_AS_A64;
                break;
        default:
                dev_err(tsi148_bridge->parent, "Invalid address space\n");
                return -EINVAL;
        }

        /* Convert 64-bit variables to 2x 32-bit variables */
        reg_split(vme_base, &vme_base_high, &vme_base_low);

        /*
         * Bound address is a valid address for the window, adjust
         * accordingly
         */
        vme_bound = vme_base + size - granularity;
        reg_split(vme_bound, &vme_bound_high, &vme_bound_low);
        pci_offset = (unsigned long long)pci_base - vme_base;
        reg_split(pci_offset, &pci_offset_high, &pci_offset_low);

        if (vme_base_low & (granularity - 1)) {
                dev_err(tsi148_bridge->parent, "Invalid VME base alignment\n");
                return -EINVAL;
        }
        if (vme_bound_low & (granularity - 1)) {
                dev_err(tsi148_bridge->parent, "Invalid VME bound alignment\n");
                return -EINVAL;
        }
        if (pci_offset_low & (granularity - 1)) {
                dev_err(tsi148_bridge->parent, "Invalid PCI Offset "
                        "alignment\n");
                return -EINVAL;
        }

        /*  Disable while we are mucking around */
        temp_ctl = ioread32be(bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITAT);
        temp_ctl &= ~TSI148_LCSR_ITAT_EN;
        iowrite32be(temp_ctl, bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITAT);

        /* Setup mapping */
        iowrite32be(vme_base_high, bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITSAU);
        iowrite32be(vme_base_low, bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITSAL);
        iowrite32be(vme_bound_high, bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITEAU);
        iowrite32be(vme_bound_low, bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITEAL);
        iowrite32be(pci_offset_high, bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITOFU);
        iowrite32be(pci_offset_low, bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITOFL);

        /* Setup 2eSST speeds */
        temp_ctl &= ~TSI148_LCSR_ITAT_2eSSTM_M;
        switch (cycle & (VME_2eSST160 | VME_2eSST267 | VME_2eSST320)) {
        case VME_2eSST160:
                temp_ctl |= TSI148_LCSR_ITAT_2eSSTM_160;
                break;
        case VME_2eSST267:
                temp_ctl |= TSI148_LCSR_ITAT_2eSSTM_267;
                break;
        case VME_2eSST320:
                temp_ctl |= TSI148_LCSR_ITAT_2eSSTM_320;
                break;
        }

        /* Setup cycle types */
        temp_ctl &= ~(0x1F << 7);
        if (cycle & VME_BLT)
                temp_ctl |= TSI148_LCSR_ITAT_BLT;
        if (cycle & VME_MBLT)
                temp_ctl |= TSI148_LCSR_ITAT_MBLT;
        if (cycle & VME_2eVME)
                temp_ctl |= TSI148_LCSR_ITAT_2eVME;
        if (cycle & VME_2eSST)
                temp_ctl |= TSI148_LCSR_ITAT_2eSST;
        if (cycle & VME_2eSSTB)
                temp_ctl |= TSI148_LCSR_ITAT_2eSSTB;

        /* Setup address space */
        temp_ctl &= ~TSI148_LCSR_ITAT_AS_M;
        temp_ctl |= addr;

        temp_ctl &= ~0xF;
        if (cycle & VME_SUPER)
                temp_ctl |= TSI148_LCSR_ITAT_SUPR ;
        if (cycle & VME_USER)
                temp_ctl |= TSI148_LCSR_ITAT_NPRIV;
        if (cycle & VME_PROG)
                temp_ctl |= TSI148_LCSR_ITAT_PGM;
        if (cycle & VME_DATA)
                temp_ctl |= TSI148_LCSR_ITAT_DATA;

        /* Write ctl reg without enable */
        iowrite32be(temp_ctl, bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITAT);

        if (enabled)
                temp_ctl |= TSI148_LCSR_ITAT_EN;

        iowrite32be(temp_ctl, bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITAT);

        return 0;
}

/*
 * Get slave window configuration.
 */
static int tsi148_slave_get(struct vme_slave_resource *image, int *enabled,
        unsigned long long *vme_base, unsigned long long *size,
        dma_addr_t *pci_base, u32 *aspace, u32 *cycle)
{
        unsigned int i, granularity = 0, ctl = 0;
        unsigned int vme_base_low, vme_base_high;
        unsigned int vme_bound_low, vme_bound_high;
        unsigned int pci_offset_low, pci_offset_high;
        unsigned long long vme_bound, pci_offset;
        struct tsi148_driver *bridge;

        bridge = image->parent->driver_priv;

        i = image->number;

        /* Read registers */
        ctl = ioread32be(bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITAT);

        vme_base_high = ioread32be(bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITSAU);
        vme_base_low = ioread32be(bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITSAL);
        vme_bound_high = ioread32be(bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITEAU);
        vme_bound_low = ioread32be(bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITEAL);
        pci_offset_high = ioread32be(bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITOFU);
        pci_offset_low = ioread32be(bridge->base + TSI148_LCSR_IT[i] +
                TSI148_LCSR_OFFSET_ITOFL);

        /* Convert 64-bit variables to 2x 32-bit variables */
        reg_join(vme_base_high, vme_base_low, vme_base);
        reg_join(vme_bound_high, vme_bound_low, &vme_bound);
        reg_join(pci_offset_high, pci_offset_low, &pci_offset);

        *pci_base = (dma_addr_t)(*vme_base + pci_offset);

        *enabled = 0;
        *aspace = 0;
        *cycle = 0;

        if (ctl & TSI148_LCSR_ITAT_EN)
                *enabled = 1;

        if ((ctl & TSI148_LCSR_ITAT_AS_M) == TSI148_LCSR_ITAT_AS_A16) {
                granularity = 0x10;
                *aspace |= VME_A16;
        }
        if ((ctl & TSI148_LCSR_ITAT_AS_M) == TSI148_LCSR_ITAT_AS_A24) {
                granularity = 0x1000;
                *aspace |= VME_A24;
        }
        if ((ctl & TSI148_LCSR_ITAT_AS_M) == TSI148_LCSR_ITAT_AS_A32) {
                granularity = 0x10000;
                *aspace |= VME_A32;
        }
        if ((ctl & TSI148_LCSR_ITAT_AS_M) == TSI148_LCSR_ITAT_AS_A64) {
                granularity = 0x10000;
                *aspace |= VME_A64;
        }

        /* Need granularity before we set the size */
        *size = (unsigned long long)((vme_bound - *vme_base) + granularity);


        if ((ctl & TSI148_LCSR_ITAT_2eSSTM_M) == TSI148_LCSR_ITAT_2eSSTM_160)
                *cycle |= VME_2eSST160;
        if ((ctl & TSI148_LCSR_ITAT_2eSSTM_M) == TSI148_LCSR_ITAT_2eSSTM_267)
                *cycle |= VME_2eSST267;
        if ((ctl & TSI148_LCSR_ITAT_2eSSTM_M) == TSI148_LCSR_ITAT_2eSSTM_320)
                *cycle |= VME_2eSST320;

        if (ctl & TSI148_LCSR_ITAT_BLT)
                *cycle |= VME_BLT;
        if (ctl & TSI148_LCSR_ITAT_MBLT)
                *cycle |= VME_MBLT;
        if (ctl & TSI148_LCSR_ITAT_2eVME)
                *cycle |= VME_2eVME;
        if (ctl & TSI148_LCSR_ITAT_2eSST)
                *cycle |= VME_2eSST;
        if (ctl & TSI148_LCSR_ITAT_2eSSTB)
                *cycle |= VME_2eSSTB;

        if (ctl & TSI148_LCSR_ITAT_SUPR)
                *cycle |= VME_SUPER;
        if (ctl & TSI148_LCSR_ITAT_NPRIV)
                *cycle |= VME_USER;
        if (ctl & TSI148_LCSR_ITAT_PGM)
                *cycle |= VME_PROG;
        if (ctl & TSI148_LCSR_ITAT_DATA)
                *cycle |= VME_DATA;

        return 0;
}

/*
 * Allocate and map PCI Resource
 */
static int tsi148_alloc_resource(struct vme_master_resource *image,
        unsigned long long size)
{
        unsigned long long existing_size;
        int retval = 0;
        struct pci_dev *pdev;
        struct vme_bridge *tsi148_bridge;

        tsi148_bridge = image->parent;

        pdev = to_pci_dev(tsi148_bridge->parent);

        existing_size = (unsigned long long)(image->bus_resource.end -
                image->bus_resource.start);

        /* If the existing size is OK, return */
        if ((size != 0) && (existing_size == (size - 1)))
                return 0;

        if (existing_size != 0) {
                iounmap(image->kern_base);
                image->kern_base = NULL;
                kfree(image->bus_resource.name);
                release_resource(&image->bus_resource);
                memset(&image->bus_resource, 0, sizeof(image->bus_resource));
        }

        /* Exit here if size is zero */
        if (size == 0)
                return 0;

        if (!image->bus_resource.name) {
                image->bus_resource.name = kmalloc(VMENAMSIZ+3, GFP_ATOMIC);
                if (!image->bus_resource.name) {
                        retval = -ENOMEM;
                        goto err_name;
                }
        }

        sprintf((char *)image->bus_resource.name, "%s.%d", tsi148_bridge->name,
                image->number);

        image->bus_resource.start = 0;
        image->bus_resource.end = (unsigned long)size;
        image->bus_resource.flags = IORESOURCE_MEM;

        retval = pci_bus_alloc_resource(pdev->bus,
                &image->bus_resource, size, 0x10000, PCIBIOS_MIN_MEM,
                0, NULL, NULL);
        if (retval) {
                dev_err(tsi148_bridge->parent, "Failed to allocate mem "
                        "resource for window %d size 0x%lx start 0x%lx\n",
                        image->number, (unsigned long)size,
                        (unsigned long)image->bus_resource.start);
                goto err_resource;
        }

        image->kern_base = ioremap(
                image->bus_resource.start, size);
        if (!image->kern_base) {
                dev_err(tsi148_bridge->parent, "Failed to remap resource\n");
                retval = -ENOMEM;
                goto err_remap;
        }

        return 0;

err_remap:
        release_resource(&image->bus_resource);
err_resource:
        kfree(image->bus_resource.name);
        memset(&image->bus_resource, 0, sizeof(image->bus_resource));
err_name:
        return retval;
}

/*
 * Free and unmap PCI Resource
 */
static void tsi148_free_resource(struct vme_master_resource *image)
{
        iounmap(image->kern_base);
        image->kern_base = NULL;
        release_resource(&image->bus_resource);
        kfree(image->bus_resource.name);
        memset(&image->bus_resource, 0, sizeof(image->bus_resource));
}

/*
 * Set the attributes of an outbound window.
 */
static int tsi148_master_set(struct vme_master_resource *image, int enabled,
        unsigned long long vme_base, unsigned long long size, u32 aspace,
        u32 cycle, u32 dwidth)
{
        int retval = 0;
        unsigned int i;
        unsigned int temp_ctl = 0;
        unsigned int pci_base_low, pci_base_high;
        unsigned int pci_bound_low, pci_bound_high;
        unsigned int vme_offset_low, vme_offset_high;
        unsigned long long pci_bound, vme_offset, pci_base;
        struct vme_bridge *tsi148_bridge;
        struct tsi148_driver *bridge;
        struct pci_bus_region region;
        struct pci_dev *pdev;

        tsi148_bridge = image->parent;

        bridge = tsi148_bridge->driver_priv;

        pdev = to_pci_dev(tsi148_bridge->parent);

        /* Verify input data */
        if (vme_base & 0xFFFF) {
                dev_err(tsi148_bridge->parent, "Invalid VME Window "
                        "alignment\n");
                retval = -EINVAL;
                goto err_window;
        }

        if ((size == 0) && (enabled != 0)) {
                dev_err(tsi148_bridge->parent, "Size must be non-zero for "
                        "enabled windows\n");
                retval = -EINVAL;
                goto err_window;
        }

        spin_lock(&image->lock);

        /* Let's allocate the resource here rather than further up the stack as
         * it avoids pushing loads of bus dependent stuff up the stack. If size
         * is zero, any existing resource will be freed.
         */
        retval = tsi148_alloc_resource(image, size);
        if (retval) {
                spin_unlock(&image->lock);
                dev_err(tsi148_bridge->parent, "Unable to allocate memory for "
                        "resource\n");
                goto err_res;
        }

        if (size == 0) {
                pci_base = 0;
                pci_bound = 0;
                vme_offset = 0;
        } else {
                pcibios_resource_to_bus(pdev->bus, &region,
                                        &image->bus_resource);
                pci_base = region.start;

                /*
                 * Bound address is a valid address for the window, adjust
                 * according to window granularity.
                 */
                pci_bound = pci_base + (size - 0x10000);
                vme_offset = vme_base - pci_base;
        }

        /* Convert 64-bit variables to 2x 32-bit variables */
        reg_split(pci_base, &pci_base_high, &pci_base_low);
        reg_split(pci_bound, &pci_bound_high, &pci_bound_low);
        reg_split(vme_offset, &vme_offset_high, &vme_offset_low);

        if (pci_base_low & 0xFFFF) {
                spin_unlock(&image->lock);
                dev_err(tsi148_bridge->parent, "Invalid PCI base alignment\n");
                retval = -EINVAL;
                goto err_gran;
        }
        if (pci_bound_low & 0xFFFF) {
                spin_unlock(&image->lock);
                dev_err(tsi148_bridge->parent, "Invalid PCI bound alignment\n");
                retval = -EINVAL;
                goto err_gran;
        }
        if (vme_offset_low & 0xFFFF) {
                spin_unlock(&image->lock);
                dev_err(tsi148_bridge->parent, "Invalid VME Offset "
                        "alignment\n");
                retval = -EINVAL;
                goto err_gran;
        }

        i = image->number;

        /* Disable while we are mucking around */
        temp_ctl = ioread32be(bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTAT);
        temp_ctl &= ~TSI148_LCSR_OTAT_EN;
        iowrite32be(temp_ctl, bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTAT);

        /* Setup 2eSST speeds */
        temp_ctl &= ~TSI148_LCSR_OTAT_2eSSTM_M;
        switch (cycle & (VME_2eSST160 | VME_2eSST267 | VME_2eSST320)) {
        case VME_2eSST160:
                temp_ctl |= TSI148_LCSR_OTAT_2eSSTM_160;
                break;
        case VME_2eSST267:
                temp_ctl |= TSI148_LCSR_OTAT_2eSSTM_267;
                break;
        case VME_2eSST320:
                temp_ctl |= TSI148_LCSR_OTAT_2eSSTM_320;
                break;
        }

        /* Setup cycle types */
        if (cycle & VME_BLT) {
                temp_ctl &= ~TSI148_LCSR_OTAT_TM_M;
                temp_ctl |= TSI148_LCSR_OTAT_TM_BLT;
        }
        if (cycle & VME_MBLT) {
                temp_ctl &= ~TSI148_LCSR_OTAT_TM_M;
                temp_ctl |= TSI148_LCSR_OTAT_TM_MBLT;
        }
        if (cycle & VME_2eVME) {
                temp_ctl &= ~TSI148_LCSR_OTAT_TM_M;
                temp_ctl |= TSI148_LCSR_OTAT_TM_2eVME;
        }
        if (cycle & VME_2eSST) {
                temp_ctl &= ~TSI148_LCSR_OTAT_TM_M;
                temp_ctl |= TSI148_LCSR_OTAT_TM_2eSST;
        }
        if (cycle & VME_2eSSTB) {
                dev_warn(tsi148_bridge->parent, "Currently not setting "
                        "Broadcast Select Registers\n");
                temp_ctl &= ~TSI148_LCSR_OTAT_TM_M;
                temp_ctl |= TSI148_LCSR_OTAT_TM_2eSSTB;
        }

        /* Setup data width */
        temp_ctl &= ~TSI148_LCSR_OTAT_DBW_M;
        switch (dwidth) {
        case VME_D16:
                temp_ctl |= TSI148_LCSR_OTAT_DBW_16;
                break;
        case VME_D32:
                temp_ctl |= TSI148_LCSR_OTAT_DBW_32;
                break;
        default:
                spin_unlock(&image->lock);
                dev_err(tsi148_bridge->parent, "Invalid data width\n");
                retval = -EINVAL;
                goto err_dwidth;
        }

        /* Setup address space */
        temp_ctl &= ~TSI148_LCSR_OTAT_AMODE_M;
        switch (aspace) {
        case VME_A16:
                temp_ctl |= TSI148_LCSR_OTAT_AMODE_A16;
                break;
        case VME_A24:
                temp_ctl |= TSI148_LCSR_OTAT_AMODE_A24;
                break;
        case VME_A32:
                temp_ctl |= TSI148_LCSR_OTAT_AMODE_A32;
                break;
        case VME_A64:
                temp_ctl |= TSI148_LCSR_OTAT_AMODE_A64;
                break;
        case VME_CRCSR:
                temp_ctl |= TSI148_LCSR_OTAT_AMODE_CRCSR;
                break;
        case VME_USER1:
                temp_ctl |= TSI148_LCSR_OTAT_AMODE_USER1;
                break;
        case VME_USER2:
                temp_ctl |= TSI148_LCSR_OTAT_AMODE_USER2;
                break;
        case VME_USER3:
                temp_ctl |= TSI148_LCSR_OTAT_AMODE_USER3;
                break;
        case VME_USER4:
                temp_ctl |= TSI148_LCSR_OTAT_AMODE_USER4;
                break;
        default:
                spin_unlock(&image->lock);
                dev_err(tsi148_bridge->parent, "Invalid address space\n");
                retval = -EINVAL;
                goto err_aspace;
        }

        temp_ctl &= ~(3<<4);
        if (cycle & VME_SUPER)

                temp_ctl |= TSI148_LCSR_OTAT_SUP;
        if (cycle & VME_PROG)
                temp_ctl |= TSI148_LCSR_OTAT_PGM;

        /* Setup mapping */
        iowrite32be(pci_base_high, bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTSAU);
        iowrite32be(pci_base_low, bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTSAL);
        iowrite32be(pci_bound_high, bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTEAU);
        iowrite32be(pci_bound_low, bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTEAL);
        iowrite32be(vme_offset_high, bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTOFU);
        iowrite32be(vme_offset_low, bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTOFL);

        /* Write ctl reg without enable */
        iowrite32be(temp_ctl, bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTAT);

        if (enabled)
                temp_ctl |= TSI148_LCSR_OTAT_EN;

        iowrite32be(temp_ctl, bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTAT);

        spin_unlock(&image->lock);
        return 0;

err_aspace:
err_dwidth:
err_gran:
        tsi148_free_resource(image);
err_res:
err_window:
        return retval;

}

/*
 * Set the attributes of an outbound window.
 *
 * XXX Not parsing prefetch information.
 */
static int __tsi148_master_get(struct vme_master_resource *image, int *enabled,
        unsigned long long *vme_base, unsigned long long *size, u32 *aspace,
        u32 *cycle, u32 *dwidth)
{
        unsigned int i, ctl;
        unsigned int pci_base_low, pci_base_high;
        unsigned int pci_bound_low, pci_bound_high;
        unsigned int vme_offset_low, vme_offset_high;

        unsigned long long pci_base, pci_bound, vme_offset;
        struct tsi148_driver *bridge;

        bridge = image->parent->driver_priv;

        i = image->number;

        ctl = ioread32be(bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTAT);

        pci_base_high = ioread32be(bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTSAU);
        pci_base_low = ioread32be(bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTSAL);
        pci_bound_high = ioread32be(bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTEAU);
        pci_bound_low = ioread32be(bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTEAL);
        vme_offset_high = ioread32be(bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTOFU);
        vme_offset_low = ioread32be(bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTOFL);

        /* Convert 64-bit variables to 2x 32-bit variables */
        reg_join(pci_base_high, pci_base_low, &pci_base);
        reg_join(pci_bound_high, pci_bound_low, &pci_bound);
        reg_join(vme_offset_high, vme_offset_low, &vme_offset);

        *vme_base = pci_base + vme_offset;
        *size = (unsigned long long)(pci_bound - pci_base) + 0x10000;

        *enabled = 0;
        *aspace = 0;
        *cycle = 0;
        *dwidth = 0;

        if (ctl & TSI148_LCSR_OTAT_EN)
                *enabled = 1;

        /* Setup address space */
        if ((ctl & TSI148_LCSR_OTAT_AMODE_M) == TSI148_LCSR_OTAT_AMODE_A16)
                *aspace |= VME_A16;
        if ((ctl & TSI148_LCSR_OTAT_AMODE_M) == TSI148_LCSR_OTAT_AMODE_A24)
                *aspace |= VME_A24;
        if ((ctl & TSI148_LCSR_OTAT_AMODE_M) == TSI148_LCSR_OTAT_AMODE_A32)
                *aspace |= VME_A32;
        if ((ctl & TSI148_LCSR_OTAT_AMODE_M) == TSI148_LCSR_OTAT_AMODE_A64)
                *aspace |= VME_A64;
        if ((ctl & TSI148_LCSR_OTAT_AMODE_M) == TSI148_LCSR_OTAT_AMODE_CRCSR)
                *aspace |= VME_CRCSR;
        if ((ctl & TSI148_LCSR_OTAT_AMODE_M) == TSI148_LCSR_OTAT_AMODE_USER1)
                *aspace |= VME_USER1;
        if ((ctl & TSI148_LCSR_OTAT_AMODE_M) == TSI148_LCSR_OTAT_AMODE_USER2)
                *aspace |= VME_USER2;
        if ((ctl & TSI148_LCSR_OTAT_AMODE_M) == TSI148_LCSR_OTAT_AMODE_USER3)
                *aspace |= VME_USER3;
        if ((ctl & TSI148_LCSR_OTAT_AMODE_M) == TSI148_LCSR_OTAT_AMODE_USER4)
                *aspace |= VME_USER4;

        /* Setup 2eSST speeds */
        if ((ctl & TSI148_LCSR_OTAT_2eSSTM_M) == TSI148_LCSR_OTAT_2eSSTM_160)
                *cycle |= VME_2eSST160;
        if ((ctl & TSI148_LCSR_OTAT_2eSSTM_M) == TSI148_LCSR_OTAT_2eSSTM_267)
                *cycle |= VME_2eSST267;
        if ((ctl & TSI148_LCSR_OTAT_2eSSTM_M) == TSI148_LCSR_OTAT_2eSSTM_320)
                *cycle |= VME_2eSST320;

        /* Setup cycle types */
        if ((ctl & TSI148_LCSR_OTAT_TM_M) == TSI148_LCSR_OTAT_TM_SCT)
                *cycle |= VME_SCT;
        if ((ctl & TSI148_LCSR_OTAT_TM_M) == TSI148_LCSR_OTAT_TM_BLT)
                *cycle |= VME_BLT;
        if ((ctl & TSI148_LCSR_OTAT_TM_M) == TSI148_LCSR_OTAT_TM_MBLT)
                *cycle |= VME_MBLT;
        if ((ctl & TSI148_LCSR_OTAT_TM_M) == TSI148_LCSR_OTAT_TM_2eVME)
                *cycle |= VME_2eVME;
        if ((ctl & TSI148_LCSR_OTAT_TM_M) == TSI148_LCSR_OTAT_TM_2eSST)
                *cycle |= VME_2eSST;
        if ((ctl & TSI148_LCSR_OTAT_TM_M) == TSI148_LCSR_OTAT_TM_2eSSTB)
                *cycle |= VME_2eSSTB;

        if (ctl & TSI148_LCSR_OTAT_SUP)
                *cycle |= VME_SUPER;
        else
                *cycle |= VME_USER;

        if (ctl & TSI148_LCSR_OTAT_PGM)
                *cycle |= VME_PROG;
        else
                *cycle |= VME_DATA;

        /* Setup data width */
        if ((ctl & TSI148_LCSR_OTAT_DBW_M) == TSI148_LCSR_OTAT_DBW_16)
                *dwidth = VME_D16;
        if ((ctl & TSI148_LCSR_OTAT_DBW_M) == TSI148_LCSR_OTAT_DBW_32)
                *dwidth = VME_D32;

        return 0;
}


static int tsi148_master_get(struct vme_master_resource *image, int *enabled,
        unsigned long long *vme_base, unsigned long long *size, u32 *aspace,
        u32 *cycle, u32 *dwidth)
{
        int retval;

        spin_lock(&image->lock);

        retval = __tsi148_master_get(image, enabled, vme_base, size, aspace,
                cycle, dwidth);

        spin_unlock(&image->lock);

        return retval;
}

static ssize_t tsi148_master_read(struct vme_master_resource *image, void *buf,
        size_t count, loff_t offset)
{
        int retval, enabled;
        unsigned long long vme_base, size;
        u32 aspace, cycle, dwidth;
        struct vme_error_handler *handler = NULL;
        struct vme_bridge *tsi148_bridge;
        void __iomem *addr = image->kern_base + offset;
        unsigned int done = 0;
        unsigned int count32;

        tsi148_bridge = image->parent;

        spin_lock(&image->lock);

        if (err_chk) {
                __tsi148_master_get(image, &enabled, &vme_base, &size, &aspace,
                                    &cycle, &dwidth);
                handler = vme_register_error_handler(tsi148_bridge, aspace,
                                                     vme_base + offset, count);
                if (!handler) {
                        spin_unlock(&image->lock);
                        return -ENOMEM;
                }
        }

        /* The following code handles VME address alignment. We cannot use
         * memcpy_xxx here because it may cut data transfers in to 8-bit
         * cycles when D16 or D32 cycles are required on the VME bus.
         * On the other hand, the bridge itself assures that the maximum data
         * cycle configured for the transfer is used and splits it
         * automatically for non-aligned addresses, so we don't want the
         * overhead of needlessly forcing small transfers for the entire cycle.
         */
        if ((uintptr_t)addr & 0x1) {
                *(u8 *)buf = ioread8(addr);
                done += 1;
                if (done == count)
                        goto out;
        }
        if ((uintptr_t)(addr + done) & 0x2) {
                if ((count - done) < 2) {
                        *(u8 *)(buf + done) = ioread8(addr + done);
                        done += 1;
                        goto out;
                } else {
                        *(u16 *)(buf + done) = ioread16(addr + done);
                        done += 2;
                }
        }

        count32 = (count - done) & ~0x3;
        while (done < count32) {
                *(u32 *)(buf + done) = ioread32(addr + done);
                done += 4;
        }

        if ((count - done) & 0x2) {
                *(u16 *)(buf + done) = ioread16(addr + done);
                done += 2;
        }
        if ((count - done) & 0x1) {
                *(u8 *)(buf + done) = ioread8(addr + done);
                done += 1;
        }

out:
        retval = count;

        if (err_chk) {
                if (handler->num_errors) {
                        dev_err(image->parent->parent,
                                "First VME read error detected an at address 0x%llx\n",
                                handler->first_error);
                        retval = handler->first_error - (vme_base + offset);
                }
                vme_unregister_error_handler(handler);
        }

        spin_unlock(&image->lock);

        return retval;
}


static ssize_t tsi148_master_write(struct vme_master_resource *image, void *buf,
        size_t count, loff_t offset)
{
        int retval = 0, enabled;
        unsigned long long vme_base, size;
        u32 aspace, cycle, dwidth;
        void __iomem *addr = image->kern_base + offset;
        unsigned int done = 0;
        unsigned int count32;

        struct vme_error_handler *handler = NULL;
        struct vme_bridge *tsi148_bridge;
        struct tsi148_driver *bridge;

        tsi148_bridge = image->parent;

        bridge = tsi148_bridge->driver_priv;

        spin_lock(&image->lock);

        if (err_chk) {
                __tsi148_master_get(image, &enabled, &vme_base, &size, &aspace,
                                    &cycle, &dwidth);
                handler = vme_register_error_handler(tsi148_bridge, aspace,
                                                     vme_base + offset, count);
                if (!handler) {
                        spin_unlock(&image->lock);
                        return -ENOMEM;
                }
        }

        /* Here we apply for the same strategy we do in master_read
         * function in order to assure the correct cycles.
         */
        if ((uintptr_t)addr & 0x1) {
                iowrite8(*(u8 *)buf, addr);
                done += 1;
                if (done == count)
                        goto out;
        }
        if ((uintptr_t)(addr + done) & 0x2) {
                if ((count - done) < 2) {
                        iowrite8(*(u8 *)(buf + done), addr + done);
                        done += 1;
                        goto out;
                } else {
                        iowrite16(*(u16 *)(buf + done), addr + done);
                        done += 2;
                }
        }

        count32 = (count - done) & ~0x3;
        while (done < count32) {
                iowrite32(*(u32 *)(buf + done), addr + done);
                done += 4;
        }

        if ((count - done) & 0x2) {
                iowrite16(*(u16 *)(buf + done), addr + done);
                done += 2;
        }
        if ((count - done) & 0x1) {
                iowrite8(*(u8 *)(buf + done), addr + done);
                done += 1;
        }

out:
        retval = count;

        /*
         * Writes are posted. We need to do a read on the VME bus to flush out
         * all of the writes before we check for errors. We can't guarantee
         * that reading the data we have just written is safe. It is believed
         * that there isn't any read, write re-ordering, so we can read any
         * location in VME space, so lets read the Device ID from the tsi148's
         * own registers as mapped into CR/CSR space.
         *
         * We check for saved errors in the written address range/space.
         */

        if (err_chk) {
                ioread16(bridge->flush_image->kern_base + 0x7F000);

                if (handler->num_errors) {
                        dev_warn(tsi148_bridge->parent,
                                 "First VME write error detected an at address 0x%llx\n",
                                 handler->first_error);
                        retval = handler->first_error - (vme_base + offset);
                }
                vme_unregister_error_handler(handler);
        }

        spin_unlock(&image->lock);

        return retval;
}

/*
 * Perform an RMW cycle on the VME bus.
 *
 * Requires a previously configured master window, returns final value.
 */
static unsigned int tsi148_master_rmw(struct vme_master_resource *image,
        unsigned int mask, unsigned int compare, unsigned int swap,
        loff_t offset)
{
        unsigned long long pci_addr;
        unsigned int pci_addr_high, pci_addr_low;
        u32 tmp, result;
        int i;
        struct tsi148_driver *bridge;

        bridge = image->parent->driver_priv;

        /* Find the PCI address that maps to the desired VME address */
        i = image->number;

        /* Locking as we can only do one of these at a time */
        mutex_lock(&bridge->vme_rmw);

        /* Lock image */
        spin_lock(&image->lock);

        pci_addr_high = ioread32be(bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTSAU);
        pci_addr_low = ioread32be(bridge->base + TSI148_LCSR_OT[i] +
                TSI148_LCSR_OFFSET_OTSAL);

        reg_join(pci_addr_high, pci_addr_low, &pci_addr);
        reg_split(pci_addr + offset, &pci_addr_high, &pci_addr_low);

        /* Configure registers */
        iowrite32be(mask, bridge->base + TSI148_LCSR_RMWEN);
        iowrite32be(compare, bridge->base + TSI148_LCSR_RMWC);
        iowrite32be(swap, bridge->base + TSI148_LCSR_RMWS);
        iowrite32be(pci_addr_high, bridge->base + TSI148_LCSR_RMWAU);
        iowrite32be(pci_addr_low, bridge->base + TSI148_LCSR_RMWAL);

        /* Enable RMW */
        tmp = ioread32be(bridge->base + TSI148_LCSR_VMCTRL);
        tmp |= TSI148_LCSR_VMCTRL_RMWEN;
        iowrite32be(tmp, bridge->base + TSI148_LCSR_VMCTRL);

        /* Kick process off with a read to the required address. */
        result = ioread32be(image->kern_base + offset);

        /* Disable RMW */
        tmp = ioread32be(bridge->base + TSI148_LCSR_VMCTRL);
        tmp &= ~TSI148_LCSR_VMCTRL_RMWEN;
        iowrite32be(tmp, bridge->base + TSI148_LCSR_VMCTRL);

        spin_unlock(&image->lock);

        mutex_unlock(&bridge->vme_rmw);

        return result;
}

static int tsi148_dma_set_vme_src_attributes(struct device *dev, __be32 *attr,
        u32 aspace, u32 cycle, u32 dwidth)
{
        u32 val;

        val = be32_to_cpu(*attr);

        /* Setup 2eSST speeds */
        switch (cycle & (VME_2eSST160 | VME_2eSST267 | VME_2eSST320)) {
        case VME_2eSST160:
                val |= TSI148_LCSR_DSAT_2eSSTM_160;
                break;
        case VME_2eSST267:
                val |= TSI148_LCSR_DSAT_2eSSTM_267;
                break;
        case VME_2eSST320:
                val |= TSI148_LCSR_DSAT_2eSSTM_320;
                break;
        }

        /* Setup cycle types */
        if (cycle & VME_SCT)
                val |= TSI148_LCSR_DSAT_TM_SCT;

        if (cycle & VME_BLT)
                val |= TSI148_LCSR_DSAT_TM_BLT;

        if (cycle & VME_MBLT)
                val |= TSI148_LCSR_DSAT_TM_MBLT;

        if (cycle & VME_2eVME)
                val |= TSI148_LCSR_DSAT_TM_2eVME;

        if (cycle & VME_2eSST)
                val |= TSI148_LCSR_DSAT_TM_2eSST;

        if (cycle & VME_2eSSTB) {
                dev_err(dev, "Currently not setting Broadcast Select "
                        "Registers\n");
                val |= TSI148_LCSR_DSAT_TM_2eSSTB;
        }

        /* Setup data width */
        switch (dwidth) {
        case VME_D16:
                val |= TSI148_LCSR_DSAT_DBW_16;
                break;
        case VME_D32:
                val |= TSI148_LCSR_DSAT_DBW_32;
                break;
        default:
                dev_err(dev, "Invalid data width\n");
                return -EINVAL;
        }

        /* Setup address space */
        switch (aspace) {
        case VME_A16:
                val |= TSI148_LCSR_DSAT_AMODE_A16;
                break;
        case VME_A24:
                val |= TSI148_LCSR_DSAT_AMODE_A24;
                break;
        case VME_A32:
                val |= TSI148_LCSR_DSAT_AMODE_A32;
                break;
        case VME_A64:
                val |= TSI148_LCSR_DSAT_AMODE_A64;
                break;
        case VME_CRCSR:
                val |= TSI148_LCSR_DSAT_AMODE_CRCSR;
                break;
        case VME_USER1:
                val |= TSI148_LCSR_DSAT_AMODE_USER1;
                break;
        case VME_USER2:
                val |= TSI148_LCSR_DSAT_AMODE_USER2;
                break;
        case VME_USER3:
                val |= TSI148_LCSR_DSAT_AMODE_USER3;
                break;
        case VME_USER4:
                val |= TSI148_LCSR_DSAT_AMODE_USER4;
                break;
        default:
                dev_err(dev, "Invalid address space\n");
                return -EINVAL;
        }

        if (cycle & VME_SUPER)
                val |= TSI148_LCSR_DSAT_SUP;
        if (cycle & VME_PROG)
                val |= TSI148_LCSR_DSAT_PGM;

        *attr = cpu_to_be32(val);

        return 0;
}

static int tsi148_dma_set_vme_dest_attributes(struct device *dev, __be32 *attr,
        u32 aspace, u32 cycle, u32 dwidth)
{
        u32 val;

        val = be32_to_cpu(*attr);

        /* Setup 2eSST speeds */
        switch (cycle & (VME_2eSST160 | VME_2eSST267 | VME_2eSST320)) {
        case VME_2eSST160:
                val |= TSI148_LCSR_DDAT_2eSSTM_160;
                break;
        case VME_2eSST267:
                val |= TSI148_LCSR_DDAT_2eSSTM_267;
                break;
        case VME_2eSST320:
                val |= TSI148_LCSR_DDAT_2eSSTM_320;
                break;
        }

        /* Setup cycle types */
        if (cycle & VME_SCT)
                val |= TSI148_LCSR_DDAT_TM_SCT;

        if (cycle & VME_BLT)
                val |= TSI148_LCSR_DDAT_TM_BLT;

        if (cycle & VME_MBLT)
                val |= TSI148_LCSR_DDAT_TM_MBLT;

        if (cycle & VME_2eVME)
                val |= TSI148_LCSR_DDAT_TM_2eVME;

        if (cycle & VME_2eSST)
                val |= TSI148_LCSR_DDAT_TM_2eSST;

        if (cycle & VME_2eSSTB) {
                dev_err(dev, "Currently not setting Broadcast Select "
                        "Registers\n");
                val |= TSI148_LCSR_DDAT_TM_2eSSTB;
        }

        /* Setup data width */
        switch (dwidth) {
        case VME_D16:
                val |= TSI148_LCSR_DDAT_DBW_16;
                break;
        case VME_D32:
                val |= TSI148_LCSR_DDAT_DBW_32;
                break;
        default:
                dev_err(dev, "Invalid data width\n");
                return -EINVAL;
        }

        /* Setup address space */
        switch (aspace) {
        case VME_A16:
                val |= TSI148_LCSR_DDAT_AMODE_A16;
                break;
        case VME_A24:
                val |= TSI148_LCSR_DDAT_AMODE_A24;
                break;
        case VME_A32:
                val |= TSI148_LCSR_DDAT_AMODE_A32;
                break;
        case VME_A64:
                val |= TSI148_LCSR_DDAT_AMODE_A64;
                break;
        case VME_CRCSR:
                val |= TSI148_LCSR_DDAT_AMODE_CRCSR;
                break;
        case VME_USER1:
                val |= TSI148_LCSR_DDAT_AMODE_USER1;
                break;
        case VME_USER2:
                val |= TSI148_LCSR_DDAT_AMODE_USER2;
                break;
        case VME_USER3:
                val |= TSI148_LCSR_DDAT_AMODE_USER3;
                break;
        case VME_USER4:
                val |= TSI148_LCSR_DDAT_AMODE_USER4;
                break;
        default:
                dev_err(dev, "Invalid address space\n");
                return -EINVAL;
        }

        if (cycle & VME_SUPER)
                val |= TSI148_LCSR_DDAT_SUP;
        if (cycle & VME_PROG)
                val |= TSI148_LCSR_DDAT_PGM;

        *attr = cpu_to_be32(val);

        return 0;
}

/*
 * Add a link list descriptor to the list
 *
 * Note: DMA engine expects the DMA descriptor to be big endian.
 */
static int tsi148_dma_list_add(struct vme_dma_list *list,
        struct vme_dma_attr *src, struct vme_dma_attr *dest, size_t count)
{
        struct tsi148_dma_entry *entry, *prev;
        u32 address_high, address_low, val;
        struct vme_dma_pattern *pattern_attr;
        struct vme_dma_pci *pci_attr;
        struct vme_dma_vme *vme_attr;
        int retval = 0;
        struct vme_bridge *tsi148_bridge;

        tsi148_bridge = list->parent->parent;

        /* Descriptor must be aligned on 64-bit boundaries */
        entry = kmalloc(sizeof(*entry), GFP_KERNEL);
        if (!entry) {
                retval = -ENOMEM;
                goto err_mem;
        }

        /* Test descriptor alignment */
        if ((unsigned long)&entry->descriptor & 0x7) {
                dev_err(tsi148_bridge->parent, "Descriptor not aligned to 8 "
                        "byte boundary as required: %p\n",
                        &entry->descriptor);
                retval = -EINVAL;
                goto err_align;
        }

        /* Given we are going to fill out the structure, we probably don't
         * need to zero it, but better safe than sorry for now.
         */
        memset(&entry->descriptor, 0, sizeof(entry->descriptor));

        /* Fill out source part */
        switch (src->type) {
        case VME_DMA_PATTERN:
                pattern_attr = src->private;

                entry->descriptor.dsal = cpu_to_be32(pattern_attr->pattern);

                val = TSI148_LCSR_DSAT_TYP_PAT;

                /* Default behaviour is 32 bit pattern */
                if (pattern_attr->type & VME_DMA_PATTERN_BYTE)
                        val |= TSI148_LCSR_DSAT_PSZ;

                /* It seems that the default behaviour is to increment */
                if ((pattern_attr->type & VME_DMA_PATTERN_INCREMENT) == 0)
                        val |= TSI148_LCSR_DSAT_NIN;
                entry->descriptor.dsat = cpu_to_be32(val);
                break;
        case VME_DMA_PCI:
                pci_attr = src->private;

                reg_split((unsigned long long)pci_attr->address, &address_high,
                        &address_low);
                entry->descriptor.dsau = cpu_to_be32(address_high);
                entry->descriptor.dsal = cpu_to_be32(address_low);
                entry->descriptor.dsat = cpu_to_be32(TSI148_LCSR_DSAT_TYP_PCI);
                break;
        case VME_DMA_VME:
                vme_attr = src->private;

                reg_split((unsigned long long)vme_attr->address, &address_high,
                        &address_low);
                entry->descriptor.dsau = cpu_to_be32(address_high);
                entry->descriptor.dsal = cpu_to_be32(address_low);
                entry->descriptor.dsat = cpu_to_be32(TSI148_LCSR_DSAT_TYP_VME);

                retval = tsi148_dma_set_vme_src_attributes(
                        tsi148_bridge->parent, &entry->descriptor.dsat,
                        vme_attr->aspace, vme_attr->cycle, vme_attr->dwidth);
                if (retval < 0)
                        goto err_source;
                break;
        default:
                dev_err(tsi148_bridge->parent, "Invalid source type\n");
                retval = -EINVAL;
                goto err_source;
        }

        /* Assume last link - this will be over-written by adding another */
        entry->descriptor.dnlau = cpu_to_be32(0);
        entry->descriptor.dnlal = cpu_to_be32(TSI148_LCSR_DNLAL_LLA);

        /* Fill out destination part */
        switch (dest->type) {
        case VME_DMA_PCI:
                pci_attr = dest->private;

                reg_split((unsigned long long)pci_attr->address, &address_high,
                        &address_low);
                entry->descriptor.ddau = cpu_to_be32(address_high);
                entry->descriptor.ddal = cpu_to_be32(address_low);
                entry->descriptor.ddat = cpu_to_be32(TSI148_LCSR_DDAT_TYP_PCI);
                break;
        case VME_DMA_VME:
                vme_attr = dest->private;

                reg_split((unsigned long long)vme_attr->address, &address_high,
                        &address_low);
                entry->descriptor.ddau = cpu_to_be32(address_high);
                entry->descriptor.ddal = cpu_to_be32(address_low);
                entry->descriptor.ddat = cpu_to_be32(TSI148_LCSR_DDAT_TYP_VME);

                retval = tsi148_dma_set_vme_dest_attributes(
                        tsi148_bridge->parent, &entry->descriptor.ddat,
                        vme_attr->aspace, vme_attr->cycle, vme_attr->dwidth);
                if (retval < 0)
                        goto err_dest;
                break;
        default:
                dev_err(tsi148_bridge->parent, "Invalid destination type\n");
                retval = -EINVAL;
                goto err_dest;
        }

        /* Fill out count */
        entry->descriptor.dcnt = cpu_to_be32((u32)count);

        /* Add to list */
        list_add_tail(&entry->list, &list->entries);

        entry->dma_handle = dma_map_single(tsi148_bridge->parent,
                                           &entry->descriptor,
                                           sizeof(entry->descriptor),
                                           DMA_TO_DEVICE);
        if (dma_mapping_error(tsi148_bridge->parent, entry->dma_handle)) {
                dev_err(tsi148_bridge->parent, "DMA mapping error\n");
                retval = -EINVAL;
                goto err_dma;
        }

        /* Fill out previous descriptors "Next Address" */
        if (entry->list.prev != &list->entries) {
                reg_split((unsigned long long)entry->dma_handle, &address_high,
                        &address_low);
                prev = list_entry(entry->list.prev, struct tsi148_dma_entry,
                                  list);
                prev->descriptor.dnlau = cpu_to_be32(address_high);
                prev->descriptor.dnlal = cpu_to_be32(address_low);

        }

        return 0;

err_dma:
err_dest:
err_source:
err_align:
                kfree(entry);
err_mem:
        return retval;
}

/*
 * Check to see if the provided DMA channel is busy.
 */
static int tsi148_dma_busy(struct vme_bridge *tsi148_bridge, int channel)
{
        u32 tmp;
        struct tsi148_driver *bridge;

        bridge = tsi148_bridge->driver_priv;

        tmp = ioread32be(bridge->base + TSI148_LCSR_DMA[channel] +
                TSI148_LCSR_OFFSET_DSTA);

        if (tmp & TSI148_LCSR_DSTA_BSY)
                return 0;
        else
                return 1;

}

/*
 * Execute a previously generated link list
 *
 * XXX Need to provide control register configuration.
 */
static int tsi148_dma_list_exec(struct vme_dma_list *list)
{
        struct vme_dma_resource *ctrlr;
        int channel, retval;
        struct tsi148_dma_entry *entry;
        u32 bus_addr_high, bus_addr_low;
        u32 val, dctlreg = 0;
        struct vme_bridge *tsi148_bridge;
        struct tsi148_driver *bridge;

        ctrlr = list->parent;

        tsi148_bridge = ctrlr->parent;

        bridge = tsi148_bridge->driver_priv;

        mutex_lock(&ctrlr->mtx);

        channel = ctrlr->number;

        if (!list_empty(&ctrlr->running)) {
                /*
                 * XXX We have an active DMA transfer and currently haven't
                 *     sorted out the mechanism for "pending" DMA transfers.
                 *     Return busy.
                 */
                /* Need to add to pending here */
                mutex_unlock(&ctrlr->mtx);
                return -EBUSY;
        } else {
                list_add(&list->list, &ctrlr->running);
        }

        /* Get first bus address and write into registers */
        entry = list_first_entry(&list->entries, struct tsi148_dma_entry,
                list);

        mutex_unlock(&ctrlr->mtx);

        reg_split(entry->dma_handle, &bus_addr_high, &bus_addr_low);

        iowrite32be(bus_addr_high, bridge->base +
                TSI148_LCSR_DMA[channel] + TSI148_LCSR_OFFSET_DNLAU);
        iowrite32be(bus_addr_low, bridge->base +
                TSI148_LCSR_DMA[channel] + TSI148_LCSR_OFFSET_DNLAL);

        dctlreg = ioread32be(bridge->base + TSI148_LCSR_DMA[channel] +
                TSI148_LCSR_OFFSET_DCTL);

        /* Start the operation */
        iowrite32be(dctlreg | TSI148_LCSR_DCTL_DGO, bridge->base +
                TSI148_LCSR_DMA[channel] + TSI148_LCSR_OFFSET_DCTL);

        retval = wait_event_interruptible(bridge->dma_queue[channel],
                tsi148_dma_busy(ctrlr->parent, channel));

        if (retval) {
                iowrite32be(dctlreg | TSI148_LCSR_DCTL_ABT, bridge->base +
                        TSI148_LCSR_DMA[channel] + TSI148_LCSR_OFFSET_DCTL);
                /* Wait for the operation to abort */
                wait_event(bridge->dma_queue[channel],
                           tsi148_dma_busy(ctrlr->parent, channel));
                retval = -EINTR;
                goto exit;
        }

        /*
         * Read status register, this register is valid until we kick off a
         * new transfer.
         */
        val = ioread32be(bridge->base + TSI148_LCSR_DMA[channel] +
                TSI148_LCSR_OFFSET_DSTA);

        if (val & TSI148_LCSR_DSTA_VBE) {
                dev_err(tsi148_bridge->parent, "DMA Error. DSTA=%08X\n", val);
                retval = -EIO;
        }

exit:
        /* Remove list from running list */
        mutex_lock(&ctrlr->mtx);
        list_del(&list->list);
        mutex_unlock(&ctrlr->mtx);

        return retval;
}

/*
 * Clean up a previously generated link list
 *
 * We have a separate function, don't assume that the chain can't be reused.
 */
static int tsi148_dma_list_empty(struct vme_dma_list *list)
{
        struct list_head *pos, *temp;
        struct tsi148_dma_entry *entry;

        struct vme_bridge *tsi148_bridge = list->parent->parent;

        /* detach and free each entry */
        list_for_each_safe(pos, temp, &list->entries) {
                list_del(pos);
                entry = list_entry(pos, struct tsi148_dma_entry, list);

                dma_unmap_single(tsi148_bridge->parent, entry->dma_handle,
                        sizeof(struct tsi148_dma_descriptor), DMA_TO_DEVICE);
                kfree(entry);
        }

        return 0;
}

/*
 * All 4 location monitors reside at the same base - this is therefore a
 * system wide configuration.
 *
 * This does not enable the LM monitor - that should be done when the first
 * callback is attached and disabled when the last callback is removed.
 */
static int tsi148_lm_set(struct vme_lm_resource *lm, unsigned long long lm_base,
        u32 aspace, u32 cycle)
{
        u32 lm_base_high, lm_base_low, lm_ctl = 0;
        int i;
        struct vme_bridge *tsi148_bridge;
        struct tsi148_driver *bridge;

        tsi148_bridge = lm->parent;

        bridge = tsi148_bridge->driver_priv;

        mutex_lock(&lm->mtx);

        /* If we already have a callback attached, we can't move it! */
        for (i = 0; i < lm->monitors; i++) {
                if (bridge->lm_callback[i]) {
                        mutex_unlock(&lm->mtx);
                        dev_err(tsi148_bridge->parent, "Location monitor "
                                "callback attached, can't reset\n");
                        return -EBUSY;
                }
        }

        switch (aspace) {
        case VME_A16:
                lm_ctl |= TSI148_LCSR_LMAT_AS_A16;
                break;
        case VME_A24:
                lm_ctl |= TSI148_LCSR_LMAT_AS_A24;
                break;
        case VME_A32:
                lm_ctl |= TSI148_LCSR_LMAT_AS_A32;
                break;
        case VME_A64:
                lm_ctl |= TSI148_LCSR_LMAT_AS_A64;
                break;
        default:
                mutex_unlock(&lm->mtx);
                dev_err(tsi148_bridge->parent, "Invalid address space\n");
                return -EINVAL;
        }

        if (cycle & VME_SUPER)
                lm_ctl |= TSI148_LCSR_LMAT_SUPR ;
        if (cycle & VME_USER)
                lm_ctl |= TSI148_LCSR_LMAT_NPRIV;
        if (cycle & VME_PROG)
                lm_ctl |= TSI148_LCSR_LMAT_PGM;
        if (cycle & VME_DATA)
                lm_ctl |= TSI148_LCSR_LMAT_DATA;

        reg_split(lm_base, &lm_base_high, &lm_base_low);

        iowrite32be(lm_base_high, bridge->base + TSI148_LCSR_LMBAU);
        iowrite32be(lm_base_low, bridge->base + TSI148_LCSR_LMBAL);
        iowrite32be(lm_ctl, bridge->base + TSI148_LCSR_LMAT);

        mutex_unlock(&lm->mtx);

        return 0;
}

/* Get configuration of the callback monitor and return whether it is enabled
 * or disabled.
 */
static int tsi148_lm_get(struct vme_lm_resource *lm,
        unsigned long long *lm_base, u32 *aspace, u32 *cycle)
{
        u32 lm_base_high, lm_base_low, lm_ctl, enabled = 0;
        struct tsi148_driver *bridge;

        bridge = lm->parent->driver_priv;

        mutex_lock(&lm->mtx);

        lm_base_high = ioread32be(bridge->base + TSI148_LCSR_LMBAU);
        lm_base_low = ioread32be(bridge->base + TSI148_LCSR_LMBAL);
        lm_ctl = ioread32be(bridge->base + TSI148_LCSR_LMAT);

        reg_join(lm_base_high, lm_base_low, lm_base);

        if (lm_ctl & TSI148_LCSR_LMAT_EN)
                enabled = 1;

        if ((lm_ctl & TSI148_LCSR_LMAT_AS_M) == TSI148_LCSR_LMAT_AS_A16)
                *aspace |= VME_A16;

        if ((lm_ctl & TSI148_LCSR_LMAT_AS_M) == TSI148_LCSR_LMAT_AS_A24)
                *aspace |= VME_A24;

        if ((lm_ctl & TSI148_LCSR_LMAT_AS_M) == TSI148_LCSR_LMAT_AS_A32)
                *aspace |= VME_A32;

        if ((lm_ctl & TSI148_LCSR_LMAT_AS_M) == TSI148_LCSR_LMAT_AS_A64)
                *aspace |= VME_A64;


        if (lm_ctl & TSI148_LCSR_LMAT_SUPR)
                *cycle |= VME_SUPER;
        if (lm_ctl & TSI148_LCSR_LMAT_NPRIV)
                *cycle |= VME_USER;
        if (lm_ctl & TSI148_LCSR_LMAT_PGM)
                *cycle |= VME_PROG;
        if (lm_ctl & TSI148_LCSR_LMAT_DATA)
                *cycle |= VME_DATA;

        mutex_unlock(&lm->mtx);

        return enabled;
}

/*
 * Attach a callback to a specific location monitor.
 *
 * Callback will be passed the monitor triggered.
 */
static int tsi148_lm_attach(struct vme_lm_resource *lm, int monitor,
        void (*callback)(void *), void *data)
{
        u32 lm_ctl, tmp;
        struct vme_bridge *tsi148_bridge;
        struct tsi148_driver *bridge;

        tsi148_bridge = lm->parent;

        bridge = tsi148_bridge->driver_priv;

        mutex_lock(&lm->mtx);

        /* Ensure that the location monitor is configured - need PGM or DATA */
        lm_ctl = ioread32be(bridge->base + TSI148_LCSR_LMAT);
        if ((lm_ctl & (TSI148_LCSR_LMAT_PGM | TSI148_LCSR_LMAT_DATA)) == 0) {
                mutex_unlock(&lm->mtx);
                dev_err(tsi148_bridge->parent, "Location monitor not properly "
                        "configured\n");
                return -EINVAL;
        }

        /* Check that a callback isn't already attached */
        if (bridge->lm_callback[monitor]) {
                mutex_unlock(&lm->mtx);
                dev_err(tsi148_bridge->parent, "Existing callback attached\n");
                return -EBUSY;
        }

        /* Attach callback */
        bridge->lm_callback[monitor] = callback;
        bridge->lm_data[monitor] = data;

        /* Enable Location Monitor interrupt */
        tmp = ioread32be(bridge->base + TSI148_LCSR_INTEN);
        tmp |= TSI148_LCSR_INTEN_LMEN[monitor];
        iowrite32be(tmp, bridge->base + TSI148_LCSR_INTEN);

        tmp = ioread32be(bridge->base + TSI148_LCSR_INTEO);
        tmp |= TSI148_LCSR_INTEO_LMEO[monitor];
        iowrite32be(tmp, bridge->base + TSI148_LCSR_INTEO);

        /* Ensure that global Location Monitor Enable set */
        if ((lm_ctl & TSI148_LCSR_LMAT_EN) == 0) {
                lm_ctl |= TSI148_LCSR_LMAT_EN;
                iowrite32be(lm_ctl, bridge->base + TSI148_LCSR_LMAT);
        }

        mutex_unlock(&lm->mtx);

        return 0;
}

/*
 * Detach a callback function forn a specific location monitor.
 */
static int tsi148_lm_detach(struct vme_lm_resource *lm, int monitor)
{
        u32 lm_en, tmp;
        struct tsi148_driver *bridge;

        bridge = lm->parent->driver_priv;

        mutex_lock(&lm->mtx);

        /* Disable Location Monitor and ensure previous interrupts are clear */
        lm_en = ioread32be(bridge->base + TSI148_LCSR_INTEN);
        lm_en &= ~TSI148_LCSR_INTEN_LMEN[monitor];
        iowrite32be(lm_en, bridge->base + TSI148_LCSR_INTEN);

        tmp = ioread32be(bridge->base + TSI148_LCSR_INTEO);
        tmp &= ~TSI148_LCSR_INTEO_LMEO[monitor];
        iowrite32be(tmp, bridge->base + TSI148_LCSR_INTEO);

        iowrite32be(TSI148_LCSR_INTC_LMC[monitor],
                 bridge->base + TSI148_LCSR_INTC);

        /* Detach callback */
        bridge->lm_callback[monitor] = NULL;
        bridge->lm_data[monitor] = NULL;

        /* If all location monitors disabled, disable global Location Monitor */
        if ((lm_en & (TSI148_LCSR_INTS_LM0S | TSI148_LCSR_INTS_LM1S |
                        TSI148_LCSR_INTS_LM2S | TSI148_LCSR_INTS_LM3S)) == 0) {
                tmp = ioread32be(bridge->base + TSI148_LCSR_LMAT);
                tmp &= ~TSI148_LCSR_LMAT_EN;
                iowrite32be(tmp, bridge->base + TSI148_LCSR_LMAT);
        }

        mutex_unlock(&lm->mtx);

        return 0;
}

/*
 * Determine Geographical Addressing
 */
static int tsi148_slot_get(struct vme_bridge *tsi148_bridge)
{
        u32 slot = 0;
        struct tsi148_driver *bridge;

        bridge = tsi148_bridge->driver_priv;

        if (!geoid) {
                slot = ioread32be(bridge->base + TSI148_LCSR_VSTAT);
                slot = slot & TSI148_LCSR_VSTAT_GA_M;
        } else
                slot = geoid;

        return (int)slot;
}

static void *tsi148_alloc_consistent(struct device *parent, size_t size,
        dma_addr_t *dma)
{
        struct pci_dev *pdev;

        /* Find pci_dev container of dev */
        pdev = to_pci_dev(parent);

        return dma_alloc_coherent(&pdev->dev, size, dma, GFP_KERNEL);
}

static void tsi148_free_consistent(struct device *parent, size_t size,
        void *vaddr, dma_addr_t dma)
{
        struct pci_dev *pdev;

        /* Find pci_dev container of dev */
        pdev = to_pci_dev(parent);

        dma_free_coherent(&pdev->dev, size, vaddr, dma);
}

/*
 * Configure CR/CSR space
 *
 * Access to the CR/CSR can be configured at power-up. The location of the
 * CR/CSR registers in the CR/CSR address space is determined by the boards
 * Auto-ID or Geographic address. This function ensures that the window is
 * enabled at an offset consistent with the boards geopgraphic address.
 *
 * Each board has a 512kB window, with the highest 4kB being used for the
 * boards registers, this means there is a fix length 508kB window which must
 * be mapped onto PCI memory.
 */
static int tsi148_crcsr_init(struct vme_bridge *tsi148_bridge,
        struct pci_dev *pdev)
{
        u32 cbar, crat, vstat;
        u32 crcsr_bus_high, crcsr_bus_low;
        int retval;
        struct tsi148_driver *bridge;

        bridge = tsi148_bridge->driver_priv;

        /* Allocate mem for CR/CSR image */
        bridge->crcsr_kernel = dma_alloc_coherent(&pdev->dev,
                                                  VME_CRCSR_BUF_SIZE,
                                                  &bridge->crcsr_bus, GFP_KERNEL);
        if (!bridge->crcsr_kernel) {
                dev_err(tsi148_bridge->parent, "Failed to allocate memory for "
                        "CR/CSR image\n");
                return -ENOMEM;
        }

        reg_split(bridge->crcsr_bus, &crcsr_bus_high, &crcsr_bus_low);

        iowrite32be(crcsr_bus_high, bridge->base + TSI148_LCSR_CROU);
        iowrite32be(crcsr_bus_low, bridge->base + TSI148_LCSR_CROL);

        /* Ensure that the CR/CSR is configured at the correct offset */
        cbar = ioread32be(bridge->base + TSI148_CBAR);
        cbar = (cbar & TSI148_CRCSR_CBAR_M)>>3;

        vstat = tsi148_slot_get(tsi148_bridge);

        if (cbar != vstat) {
                cbar = vstat;
                dev_info(tsi148_bridge->parent, "Setting CR/CSR offset\n");
                iowrite32be(cbar<<3, bridge->base + TSI148_CBAR);
        }
        dev_info(tsi148_bridge->parent, "CR/CSR Offset: %d\n", cbar);

        crat = ioread32be(bridge->base + TSI148_LCSR_CRAT);
        if (crat & TSI148_LCSR_CRAT_EN)
                dev_info(tsi148_bridge->parent, "CR/CSR already enabled\n");
        else {
                dev_info(tsi148_bridge->parent, "Enabling CR/CSR space\n");
                iowrite32be(crat | TSI148_LCSR_CRAT_EN,
                        bridge->base + TSI148_LCSR_CRAT);
        }

        /* If we want flushed, error-checked writes, set up a window
         * over the CR/CSR registers. We read from here to safely flush
         * through VME writes.
         */
        if (err_chk) {
                retval = tsi148_master_set(bridge->flush_image, 1,
                        (vstat * 0x80000), 0x80000, VME_CRCSR, VME_SCT,
                        VME_D16);
                if (retval)
                        dev_err(tsi148_bridge->parent, "Configuring flush image"
                                " failed\n");
        }

        return 0;

}

static void tsi148_crcsr_exit(struct vme_bridge *tsi148_bridge,
        struct pci_dev *pdev)
{
        u32 crat;
        struct tsi148_driver *bridge;

        bridge = tsi148_bridge->driver_priv;

        /* Turn off CR/CSR space */
        crat = ioread32be(bridge->base + TSI148_LCSR_CRAT);
        iowrite32be(crat & ~TSI148_LCSR_CRAT_EN,
                bridge->base + TSI148_LCSR_CRAT);

        /* Free image */
        iowrite32be(0, bridge->base + TSI148_LCSR_CROU);
        iowrite32be(0, bridge->base + TSI148_LCSR_CROL);

        dma_free_coherent(&pdev->dev, VME_CRCSR_BUF_SIZE,
                          bridge->crcsr_kernel, bridge->crcsr_bus);
}

static int tsi148_probe(struct pci_dev *pdev, const struct pci_device_id *id)
{
        int retval, i, master_num;
        u32 data;
        struct list_head *pos = NULL, *n;
        struct vme_bridge *tsi148_bridge;
        struct tsi148_driver *tsi148_device;
        struct vme_master_resource *master_image;
        struct vme_slave_resource *slave_image;
        struct vme_dma_resource *dma_ctrlr;
        struct vme_lm_resource *lm;

        /* If we want to support more than one of each bridge, we need to
         * dynamically generate this so we get one per device
         */
        tsi148_bridge = kzalloc(sizeof(*tsi148_bridge), GFP_KERNEL);
        if (!tsi148_bridge) {
                retval = -ENOMEM;
                goto err_struct;
        }
        vme_init_bridge(tsi148_bridge);

        tsi148_device = kzalloc(sizeof(*tsi148_device), GFP_KERNEL);
        if (!tsi148_device) {
                retval = -ENOMEM;
                goto err_driver;
        }

        tsi148_bridge->driver_priv = tsi148_device;

        /* Enable the device */
        retval = pci_enable_device(pdev);
        if (retval) {
                dev_err(&pdev->dev, "Unable to enable device\n");
                goto err_enable;
        }

        /* Map Registers */
        retval = pci_request_regions(pdev, driver_name);
        if (retval) {
                dev_err(&pdev->dev, "Unable to reserve resources\n");
                goto err_resource;
        }

        /* map registers in BAR 0 */
        tsi148_device->base = ioremap(pci_resource_start(pdev, 0),
                4096);
        if (!tsi148_device->base) {
                dev_err(&pdev->dev, "Unable to remap CRG region\n");
                retval = -EIO;
                goto err_remap;
        }

        /* Check to see if the mapping worked out */
        data = ioread32(tsi148_device->base + TSI148_PCFS_ID) & 0x0000FFFF;
        if (data != PCI_VENDOR_ID_TUNDRA) {
                dev_err(&pdev->dev, "CRG region check failed\n");
                retval = -EIO;
                goto err_test;
        }

        /* Initialize wait queues & mutual exclusion flags */
        init_waitqueue_head(&tsi148_device->dma_queue[0]);
        init_waitqueue_head(&tsi148_device->dma_queue[1]);
        init_waitqueue_head(&tsi148_device->iack_queue);
        mutex_init(&tsi148_device->vme_int);
        mutex_init(&tsi148_device->vme_rmw);

        tsi148_bridge->parent = &pdev->dev;
        strcpy(tsi148_bridge->name, driver_name);

        /* Setup IRQ */
        retval = tsi148_irq_init(tsi148_bridge);
        if (retval != 0) {
                dev_err(&pdev->dev, "Chip Initialization failed.\n");
                goto err_irq;
        }

        /* If we are going to flush writes, we need to read from the VME bus.
         * We need to do this safely, thus we read the devices own CR/CSR
         * register. To do this we must set up a window in CR/CSR space and
         * hence have one less master window resource available.
         */
        master_num = TSI148_MAX_MASTER;
        if (err_chk) {
                master_num--;

                tsi148_device->flush_image =
                        kmalloc(sizeof(*tsi148_device->flush_image),
                                GFP_KERNEL);
                if (!tsi148_device->flush_image) {
                        retval = -ENOMEM;
                        goto err_master;
                }
                tsi148_device->flush_image->parent = tsi148_bridge;
                spin_lock_init(&tsi148_device->flush_image->lock);
                tsi148_device->flush_image->locked = 1;
                tsi148_device->flush_image->number = master_num;
                memset(&tsi148_device->flush_image->bus_resource, 0,
                       sizeof(tsi148_device->flush_image->bus_resource));
                tsi148_device->flush_image->kern_base  = NULL;
        }

        /* Add master windows to list */
        for (i = 0; i < master_num; i++) {
                master_image = kmalloc(sizeof(*master_image), GFP_KERNEL);
                if (!master_image) {
                        retval = -ENOMEM;
                        goto err_master;
                }
                master_image->parent = tsi148_bridge;
                spin_lock_init(&master_image->lock);
                master_image->locked = 0;
                master_image->number = i;
                master_image->address_attr = VME_A16 | VME_A24 | VME_A32 |
                        VME_A64 | VME_CRCSR | VME_USER1 | VME_USER2 |
                        VME_USER3 | VME_USER4;
                master_image->cycle_attr = VME_SCT | VME_BLT | VME_MBLT |
                        VME_2eVME | VME_2eSST | VME_2eSSTB | VME_2eSST160 |
                        VME_2eSST267 | VME_2eSST320 | VME_SUPER | VME_USER |
                        VME_PROG | VME_DATA;
                master_image->width_attr = VME_D16 | VME_D32;
                memset(&master_image->bus_resource, 0,
                       sizeof(master_image->bus_resource));
                master_image->kern_base  = NULL;
                list_add_tail(&master_image->list,
                        &tsi148_bridge->master_resources);
        }

        /* Add slave windows to list */
        for (i = 0; i < TSI148_MAX_SLAVE; i++) {
                slave_image = kmalloc(sizeof(*slave_image), GFP_KERNEL);
                if (!slave_image) {
                        retval = -ENOMEM;
                        goto err_slave;
                }
                slave_image->parent = tsi148_bridge;
                mutex_init(&slave_image->mtx);
                slave_image->locked = 0;
                slave_image->number = i;
                slave_image->address_attr = VME_A16 | VME_A24 | VME_A32 |
                        VME_A64;
                slave_image->cycle_attr = VME_SCT | VME_BLT | VME_MBLT |
                        VME_2eVME | VME_2eSST | VME_2eSSTB | VME_2eSST160 |
                        VME_2eSST267 | VME_2eSST320 | VME_SUPER | VME_USER |
                        VME_PROG | VME_DATA;
                list_add_tail(&slave_image->list,
                        &tsi148_bridge->slave_resources);
        }

        /* Add dma engines to list */
        for (i = 0; i < TSI148_MAX_DMA; i++) {
                dma_ctrlr = kmalloc(sizeof(*dma_ctrlr), GFP_KERNEL);
                if (!dma_ctrlr) {
                        retval = -ENOMEM;
                        goto err_dma;
                }
                dma_ctrlr->parent = tsi148_bridge;
                mutex_init(&dma_ctrlr->mtx);
                dma_ctrlr->locked = 0;
                dma_ctrlr->number = i;
                dma_ctrlr->route_attr = VME_DMA_VME_TO_MEM |
                        VME_DMA_MEM_TO_VME | VME_DMA_VME_TO_VME |
                        VME_DMA_MEM_TO_MEM | VME_DMA_PATTERN_TO_VME |
                        VME_DMA_PATTERN_TO_MEM;
                INIT_LIST_HEAD(&dma_ctrlr->pending);
                INIT_LIST_HEAD(&dma_ctrlr->running);
                list_add_tail(&dma_ctrlr->list,
                        &tsi148_bridge->dma_resources);
        }

        /* Add location monitor to list */
        lm = kmalloc(sizeof(*lm), GFP_KERNEL);
        if (!lm) {
                retval = -ENOMEM;
                goto err_lm;
        }
        lm->parent = tsi148_bridge;
        mutex_init(&lm->mtx);
        lm->locked = 0;
        lm->number = 1;
        lm->monitors = 4;
        list_add_tail(&lm->list, &tsi148_bridge->lm_resources);

        tsi148_bridge->slave_get = tsi148_slave_get;
        tsi148_bridge->slave_set = tsi148_slave_set;
        tsi148_bridge->master_get = tsi148_master_get;
        tsi148_bridge->master_set = tsi148_master_set;
        tsi148_bridge->master_read = tsi148_master_read;
        tsi148_bridge->master_write = tsi148_master_write;
        tsi148_bridge->master_rmw = tsi148_master_rmw;
        tsi148_bridge->dma_list_add = tsi148_dma_list_add;
        tsi148_bridge->dma_list_exec = tsi148_dma_list_exec;
        tsi148_bridge->dma_list_empty = tsi148_dma_list_empty;
        tsi148_bridge->irq_set = tsi148_irq_set;
        tsi148_bridge->irq_generate = tsi148_irq_generate;
        tsi148_bridge->lm_set = tsi148_lm_set;
        tsi148_bridge->lm_get = tsi148_lm_get;
        tsi148_bridge->lm_attach = tsi148_lm_attach;
        tsi148_bridge->lm_detach = tsi148_lm_detach;
        tsi148_bridge->slot_get = tsi148_slot_get;
        tsi148_bridge->alloc_consistent = tsi148_alloc_consistent;
        tsi148_bridge->free_consistent = tsi148_free_consistent;

        data = ioread32be(tsi148_device->base + TSI148_LCSR_VSTAT);
        dev_info(&pdev->dev, "Board is%s the VME system controller\n",
                (data & TSI148_LCSR_VSTAT_SCONS) ? "" : " not");
        if (!geoid)
                dev_info(&pdev->dev, "VME geographical address is %d\n",
                        data & TSI148_LCSR_VSTAT_GA_M);
        else
                dev_info(&pdev->dev, "VME geographical address is set to %d\n",
                        geoid);

        dev_info(&pdev->dev, "VME Write and flush and error check is %s\n",
                err_chk ? "enabled" : "disabled");

        retval = tsi148_crcsr_init(tsi148_bridge, pdev);
        if (retval) {
                dev_err(&pdev->dev, "CR/CSR configuration failed.\n");
                goto err_crcsr;
        }

        retval = vme_register_bridge(tsi148_bridge);
        if (retval != 0) {
                dev_err(&pdev->dev, "Chip Registration failed.\n");
                goto err_reg;
        }

        pci_set_drvdata(pdev, tsi148_bridge);

        /* Clear VME bus "board fail", and "power-up reset" lines */
        data = ioread32be(tsi148_device->base + TSI148_LCSR_VSTAT);
        data &= ~TSI148_LCSR_VSTAT_BRDFL;
        data |= TSI148_LCSR_VSTAT_CPURST;
        iowrite32be(data, tsi148_device->base + TSI148_LCSR_VSTAT);

        return 0;

err_reg:
        tsi148_crcsr_exit(tsi148_bridge, pdev);
err_crcsr:
err_lm:
        /* resources are stored in link list */
        list_for_each_safe(pos, n, &tsi148_bridge->lm_resources) {
                lm = list_entry(pos, struct vme_lm_resource, list);
                list_del(pos);
                kfree(lm);
        }
err_dma:
        /* resources are stored in link list */
        list_for_each_safe(pos, n, &tsi148_bridge->dma_resources) {
                dma_ctrlr = list_entry(pos, struct vme_dma_resource, list);
                list_del(pos);
                kfree(dma_ctrlr);
        }
err_slave:
        /* resources are stored in link list */
        list_for_each_safe(pos, n, &tsi148_bridge->slave_resources) {
                slave_image = list_entry(pos, struct vme_slave_resource, list);
                list_del(pos);
                kfree(slave_image);
        }
err_master:
        /* resources are stored in link list */
        list_for_each_safe(pos, n, &tsi148_bridge->master_resources) {
                master_image = list_entry(pos, struct vme_master_resource,
                        list);
                list_del(pos);
                kfree(master_image);
        }

        tsi148_irq_exit(tsi148_bridge, pdev);
err_irq:
err_test:
        iounmap(tsi148_device->base);
err_remap:
        pci_release_regions(pdev);
err_resource:
        pci_disable_device(pdev);
err_enable:
        kfree(tsi148_device);
err_driver:
        kfree(tsi148_bridge);
err_struct:
        return retval;

}

static void tsi148_remove(struct pci_dev *pdev)
{
        struct list_head *pos = NULL;
        struct list_head *tmplist;
        struct vme_master_resource *master_image;
        struct vme_slave_resource *slave_image;
        struct vme_dma_resource *dma_ctrlr;
        int i;
        struct tsi148_driver *bridge;
        struct vme_bridge *tsi148_bridge = pci_get_drvdata(pdev);

        bridge = tsi148_bridge->driver_priv;


        dev_dbg(&pdev->dev, "Driver is being unloaded.\n");

        /*
         *  Shutdown all inbound and outbound windows.
         */
        for (i = 0; i < 8; i++) {
                iowrite32be(0, bridge->base + TSI148_LCSR_IT[i] +
                        TSI148_LCSR_OFFSET_ITAT);
                iowrite32be(0, bridge->base + TSI148_LCSR_OT[i] +
                        TSI148_LCSR_OFFSET_OTAT);
        }

        /*
         *  Shutdown Location monitor.
         */
        iowrite32be(0, bridge->base + TSI148_LCSR_LMAT);

        /*
         *  Shutdown CRG map.
         */
        iowrite32be(0, bridge->base + TSI148_LCSR_CSRAT);

        /*
         *  Clear error status.
         */
        iowrite32be(0xFFFFFFFF, bridge->base + TSI148_LCSR_EDPAT);
        iowrite32be(0xFFFFFFFF, bridge->base + TSI148_LCSR_VEAT);
        iowrite32be(0x07000700, bridge->base + TSI148_LCSR_PSTAT);

        /*
         *  Remove VIRQ interrupt (if any)
         */
        if (ioread32be(bridge->base + TSI148_LCSR_VICR) & 0x800)
                iowrite32be(0x8000, bridge->base + TSI148_LCSR_VICR);

        /*
         *  Map all Interrupts to PCI INTA
         */
        iowrite32be(0x0, bridge->base + TSI148_LCSR_INTM1);
        iowrite32be(0x0, bridge->base + TSI148_LCSR_INTM2);

        tsi148_irq_exit(tsi148_bridge, pdev);

        vme_unregister_bridge(tsi148_bridge);

        tsi148_crcsr_exit(tsi148_bridge, pdev);

        /* resources are stored in link list */
        list_for_each_safe(pos, tmplist, &tsi148_bridge->dma_resources) {
                dma_ctrlr = list_entry(pos, struct vme_dma_resource, list);
                list_del(pos);
                kfree(dma_ctrlr);
        }

        /* resources are stored in link list */
        list_for_each_safe(pos, tmplist, &tsi148_bridge->slave_resources) {
                slave_image = list_entry(pos, struct vme_slave_resource, list);
                list_del(pos);
                kfree(slave_image);
        }

        /* resources are stored in link list */
        list_for_each_safe(pos, tmplist, &tsi148_bridge->master_resources) {
                master_image = list_entry(pos, struct vme_master_resource,
                        list);
                list_del(pos);
                kfree(master_image);
        }

        iounmap(bridge->base);

        pci_release_regions(pdev);

        pci_disable_device(pdev);

        kfree(tsi148_bridge->driver_priv);

        kfree(tsi148_bridge);
}

module_pci_driver(tsi148_driver);

MODULE_PARM_DESC(err_chk, "Check for VME errors on reads and writes");
module_param(err_chk, bool, 0);

MODULE_PARM_DESC(geoid, "Override geographical addressing");
module_param(geoid, int, 0);

MODULE_DESCRIPTION("VME driver for the Tundra Tempe VME bridge");
MODULE_LICENSE("GPL");