// SPDX-License-Identifier: GPL-2.0
/* Copyright(c) 1999 - 2018 Intel Corporation. */

/* 80003ES2LAN Gigabit Ethernet Controller (Copper)
 * 80003ES2LAN Gigabit Ethernet Controller (Serdes)
 */

#include "e1000.h"

/* A table for the GG82563 cable length where the range is defined
 * with a lower bound at "index" and the upper bound at
 * "index + 5".
 */
static const u16 e1000_gg82563_cable_length_table[] = {
        0, 60, 115, 150, 150, 60, 115, 150, 180, 180, 0xFF
};

#define GG82563_CABLE_LENGTH_TABLE_SIZE \
                ARRAY_SIZE(e1000_gg82563_cable_length_table)

static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw);
static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw);
static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw);
static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw);
static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex);
static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
                                           u16 *data);
static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
                                            u16 data);
static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw);

/**
 *  e1000_init_phy_params_80003es2lan - Init ESB2 PHY func ptrs.
 *  @hw: pointer to the HW structure
 **/
static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw)
{
        struct e1000_phy_info *phy = &hw->phy;
        s32 ret_val;

        if (hw->phy.media_type != e1000_media_type_copper) {
                phy->type = e1000_phy_none;
                return 0;
        } else {
                phy->ops.power_up = e1000_power_up_phy_copper;
                phy->ops.power_down = e1000_power_down_phy_copper_80003es2lan;
        }

        phy->addr = 1;
        phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
        phy->reset_delay_us = 100;
        phy->type = e1000_phy_gg82563;

        /* This can only be done after all function pointers are setup. */
        ret_val = e1000e_get_phy_id(hw);

        /* Verify phy id */
        if (phy->id != GG82563_E_PHY_ID)
                return -E1000_ERR_PHY;

        return ret_val;
}

/**
 *  e1000_init_nvm_params_80003es2lan - Init ESB2 NVM func ptrs.
 *  @hw: pointer to the HW structure
 **/
static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw)
{
        struct e1000_nvm_info *nvm = &hw->nvm;
        u32 eecd = er32(EECD);
        u16 size;

        nvm->opcode_bits = 8;
        nvm->delay_usec = 1;
        switch (nvm->override) {
        case e1000_nvm_override_spi_large:
                nvm->page_size = 32;
                nvm->address_bits = 16;
                break;
        case e1000_nvm_override_spi_small:
                nvm->page_size = 8;
                nvm->address_bits = 8;
                break;
        default:
                nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
                nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
                break;
        }

        nvm->type = e1000_nvm_eeprom_spi;

        size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
                     E1000_EECD_SIZE_EX_SHIFT);

        /* Added to a constant, "size" becomes the left-shift value
         * for setting word_size.
         */
        size += NVM_WORD_SIZE_BASE_SHIFT;

        /* EEPROM access above 16k is unsupported */
        if (size > 14)
                size = 14;
        nvm->word_size = BIT(size);

        return 0;
}

/**
 *  e1000_init_mac_params_80003es2lan - Init ESB2 MAC func ptrs.
 *  @hw: pointer to the HW structure
 **/
static s32 e1000_init_mac_params_80003es2lan(struct e1000_hw *hw)
{
        struct e1000_mac_info *mac = &hw->mac;

        /* Set media type and media-dependent function pointers */
        switch (hw->adapter->pdev->device) {
        case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
                hw->phy.media_type = e1000_media_type_internal_serdes;
                mac->ops.check_for_link = e1000e_check_for_serdes_link;
                mac->ops.setup_physical_interface =
                    e1000e_setup_fiber_serdes_link;
                break;
        default:
                hw->phy.media_type = e1000_media_type_copper;
                mac->ops.check_for_link = e1000e_check_for_copper_link;
                mac->ops.setup_physical_interface =
                    e1000_setup_copper_link_80003es2lan;
                break;
        }

        /* Set mta register count */
        mac->mta_reg_count = 128;
        /* Set rar entry count */
        mac->rar_entry_count = E1000_RAR_ENTRIES;
        /* FWSM register */
        mac->has_fwsm = true;
        /* ARC supported; valid only if manageability features are enabled. */
        mac->arc_subsystem_valid = !!(er32(FWSM) & E1000_FWSM_MODE_MASK);
        /* Adaptive IFS not supported */
        mac->adaptive_ifs = false;

        /* set lan id for port to determine which phy lock to use */
        hw->mac.ops.set_lan_id(hw);

        return 0;
}

static s32 e1000_get_variants_80003es2lan(struct e1000_adapter *adapter)
{
        struct e1000_hw *hw = &adapter->hw;
        s32 rc;

        rc = e1000_init_mac_params_80003es2lan(hw);
        if (rc)
                return rc;

        rc = e1000_init_nvm_params_80003es2lan(hw);
        if (rc)
                return rc;

        rc = e1000_init_phy_params_80003es2lan(hw);
        if (rc)
                return rc;

        return 0;
}

/**
 *  e1000_acquire_phy_80003es2lan - Acquire rights to access PHY
 *  @hw: pointer to the HW structure
 *
 *  A wrapper to acquire access rights to the correct PHY.
 **/
static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw)
{
        u16 mask;

        mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
        return e1000_acquire_swfw_sync_80003es2lan(hw, mask);
}

/**
 *  e1000_release_phy_80003es2lan - Release rights to access PHY
 *  @hw: pointer to the HW structure
 *
 *  A wrapper to release access rights to the correct PHY.
 **/
static void e1000_release_phy_80003es2lan(struct e1000_hw *hw)
{
        u16 mask;

        mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
        e1000_release_swfw_sync_80003es2lan(hw, mask);
}

/**
 *  e1000_acquire_mac_csr_80003es2lan - Acquire right to access Kumeran register
 *  @hw: pointer to the HW structure
 *
 *  Acquire the semaphore to access the Kumeran interface.
 *
 **/
static s32 e1000_acquire_mac_csr_80003es2lan(struct e1000_hw *hw)
{
        u16 mask;

        mask = E1000_SWFW_CSR_SM;

        return e1000_acquire_swfw_sync_80003es2lan(hw, mask);
}

/**
 *  e1000_release_mac_csr_80003es2lan - Release right to access Kumeran Register
 *  @hw: pointer to the HW structure
 *
 *  Release the semaphore used to access the Kumeran interface
 **/
static void e1000_release_mac_csr_80003es2lan(struct e1000_hw *hw)
{
        u16 mask;

        mask = E1000_SWFW_CSR_SM;

        e1000_release_swfw_sync_80003es2lan(hw, mask);
}

/**
 *  e1000_acquire_nvm_80003es2lan - Acquire rights to access NVM
 *  @hw: pointer to the HW structure
 *
 *  Acquire the semaphore to access the EEPROM.
 **/
static s32 e1000_acquire_nvm_80003es2lan(struct e1000_hw *hw)
{
        s32 ret_val;

        ret_val = e1000_acquire_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
        if (ret_val)
                return ret_val;

        ret_val = e1000e_acquire_nvm(hw);

        if (ret_val)
                e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);

        return ret_val;
}

/**
 *  e1000_release_nvm_80003es2lan - Relinquish rights to access NVM
 *  @hw: pointer to the HW structure
 *
 *  Release the semaphore used to access the EEPROM.
 **/
static void e1000_release_nvm_80003es2lan(struct e1000_hw *hw)
{
        e1000e_release_nvm(hw);
        e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
}

/**
 *  e1000_acquire_swfw_sync_80003es2lan - Acquire SW/FW semaphore
 *  @hw: pointer to the HW structure
 *  @mask: specifies which semaphore to acquire
 *
 *  Acquire the SW/FW semaphore to access the PHY or NVM.  The mask
 *  will also specify which port we're acquiring the lock for.
 **/
static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
{
        u32 swfw_sync;
        u32 swmask = mask;
        u32 fwmask = mask << 16;
        s32 i = 0;
        s32 timeout = 50;

        while (i < timeout) {
                if (e1000e_get_hw_semaphore(hw))
                        return -E1000_ERR_SWFW_SYNC;

                swfw_sync = er32(SW_FW_SYNC);
                if (!(swfw_sync & (fwmask | swmask)))
                        break;

                /* Firmware currently using resource (fwmask)
                 * or other software thread using resource (swmask)
                 */
                e1000e_put_hw_semaphore(hw);
                mdelay(5);
                i++;
        }

        if (i == timeout) {
                e_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n");
                return -E1000_ERR_SWFW_SYNC;
        }

        swfw_sync |= swmask;
        ew32(SW_FW_SYNC, swfw_sync);

        e1000e_put_hw_semaphore(hw);

        return 0;
}

/**
 *  e1000_release_swfw_sync_80003es2lan - Release SW/FW semaphore
 *  @hw: pointer to the HW structure
 *  @mask: specifies which semaphore to acquire
 *
 *  Release the SW/FW semaphore used to access the PHY or NVM.  The mask
 *  will also specify which port we're releasing the lock for.
 **/
static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
{
        u32 swfw_sync;

        while (e1000e_get_hw_semaphore(hw) != 0)
                ; /* Empty */

        swfw_sync = er32(SW_FW_SYNC);
        swfw_sync &= ~mask;
        ew32(SW_FW_SYNC, swfw_sync);

        e1000e_put_hw_semaphore(hw);
}

/**
 *  e1000_read_phy_reg_gg82563_80003es2lan - Read GG82563 PHY register
 *  @hw: pointer to the HW structure
 *  @offset: offset of the register to read
 *  @data: pointer to the data returned from the operation
 *
 *  Read the GG82563 PHY register.
 **/
static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
                                                  u32 offset, u16 *data)
{
        s32 ret_val;
        u32 page_select;
        u16 temp;

        ret_val = e1000_acquire_phy_80003es2lan(hw);
        if (ret_val)
                return ret_val;

        /* Select Configuration Page */
        if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
                page_select = GG82563_PHY_PAGE_SELECT;
        } else {
                /* Use Alternative Page Select register to access
                 * registers 30 and 31
                 */
                page_select = GG82563_PHY_PAGE_SELECT_ALT;
        }

        temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
        ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
        if (ret_val) {
                e1000_release_phy_80003es2lan(hw);
                return ret_val;
        }

        if (hw->dev_spec.e80003es2lan.mdic_wa_enable) {
                /* The "ready" bit in the MDIC register may be incorrectly set
                 * before the device has completed the "Page Select" MDI
                 * transaction.  So we wait 200us after each MDI command...
                 */
                usleep_range(200, 400);

                /* ...and verify the command was successful. */
                ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);

                if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
                        e1000_release_phy_80003es2lan(hw);
                        return -E1000_ERR_PHY;
                }

                usleep_range(200, 400);

                ret_val = e1000e_read_phy_reg_mdic(hw,
                                                   MAX_PHY_REG_ADDRESS & offset,
                                                   data);

                usleep_range(200, 400);
        } else {
                ret_val = e1000e_read_phy_reg_mdic(hw,
                                                   MAX_PHY_REG_ADDRESS & offset,
                                                   data);
        }

        e1000_release_phy_80003es2lan(hw);

        return ret_val;
}

/**
 *  e1000_write_phy_reg_gg82563_80003es2lan - Write GG82563 PHY register
 *  @hw: pointer to the HW structure
 *  @offset: offset of the register to read
 *  @data: value to write to the register
 *
 *  Write to the GG82563 PHY register.
 **/
static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
                                                   u32 offset, u16 data)
{
        s32 ret_val;
        u32 page_select;
        u16 temp;

        ret_val = e1000_acquire_phy_80003es2lan(hw);
        if (ret_val)
                return ret_val;

        /* Select Configuration Page */
        if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
                page_select = GG82563_PHY_PAGE_SELECT;
        } else {
                /* Use Alternative Page Select register to access
                 * registers 30 and 31
                 */
                page_select = GG82563_PHY_PAGE_SELECT_ALT;
        }

        temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
        ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
        if (ret_val) {
                e1000_release_phy_80003es2lan(hw);
                return ret_val;
        }

        if (hw->dev_spec.e80003es2lan.mdic_wa_enable) {
                /* The "ready" bit in the MDIC register may be incorrectly set
                 * before the device has completed the "Page Select" MDI
                 * transaction.  So we wait 200us after each MDI command...
                 */
                usleep_range(200, 400);

                /* ...and verify the command was successful. */
                ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);

                if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
                        e1000_release_phy_80003es2lan(hw);
                        return -E1000_ERR_PHY;
                }

                usleep_range(200, 400);

                ret_val = e1000e_write_phy_reg_mdic(hw,
                                                    MAX_PHY_REG_ADDRESS &
                                                    offset, data);

                usleep_range(200, 400);
        } else {
                ret_val = e1000e_write_phy_reg_mdic(hw,
                                                    MAX_PHY_REG_ADDRESS &
                                                    offset, data);
        }

        e1000_release_phy_80003es2lan(hw);

        return ret_val;
}

/**
 *  e1000_write_nvm_80003es2lan - Write to ESB2 NVM
 *  @hw: pointer to the HW structure
 *  @offset: offset of the register to read
 *  @words: number of words to write
 *  @data: buffer of data to write to the NVM
 *
 *  Write "words" of data to the ESB2 NVM.
 **/
static s32 e1000_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset,
                                       u16 words, u16 *data)
{
        return e1000e_write_nvm_spi(hw, offset, words, data);
}

/**
 *  e1000_get_cfg_done_80003es2lan - Wait for configuration to complete
 *  @hw: pointer to the HW structure
 *
 *  Wait a specific amount of time for manageability processes to complete.
 *  This is a function pointer entry point called by the phy module.
 **/
static s32 e1000_get_cfg_done_80003es2lan(struct e1000_hw *hw)
{
        s32 timeout = PHY_CFG_TIMEOUT;
        u32 mask = E1000_NVM_CFG_DONE_PORT_0;

        if (hw->bus.func == 1)
                mask = E1000_NVM_CFG_DONE_PORT_1;

        while (timeout) {
                if (er32(EEMNGCTL) & mask)
                        break;
                usleep_range(1000, 2000);
                timeout--;
        }
        if (!timeout) {
                e_dbg("MNG configuration cycle has not completed.\n");
                return -E1000_ERR_RESET;
        }

        return 0;
}

/**
 *  e1000_phy_force_speed_duplex_80003es2lan - Force PHY speed and duplex
 *  @hw: pointer to the HW structure
 *
 *  Force the speed and duplex settings onto the PHY.  This is a
 *  function pointer entry point called by the phy module.
 **/
static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
{
        s32 ret_val;
        u16 phy_data;
        bool link;

        /* Clear Auto-Crossover to force MDI manually.  M88E1000 requires MDI
         * forced whenever speed and duplex are forced.
         */
        ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
        if (ret_val)
                return ret_val;

        phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_AUTO;
        ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, phy_data);
        if (ret_val)
                return ret_val;

        e_dbg("GG82563 PSCR: %X\n", phy_data);

        ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
        if (ret_val)
                return ret_val;

        e1000e_phy_force_speed_duplex_setup(hw, &phy_data);

        /* Reset the phy to commit changes. */
        phy_data |= BMCR_RESET;

        ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
        if (ret_val)
                return ret_val;

        udelay(1);

        if (hw->phy.autoneg_wait_to_complete) {
                e_dbg("Waiting for forced speed/duplex link on GG82563 phy.\n");

                ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
                                                      100000, &link);
                if (ret_val)
                        return ret_val;

                if (!link) {
                        /* We didn't get link.
                         * Reset the DSP and cross our fingers.
                         */
                        ret_val = e1000e_phy_reset_dsp(hw);
                        if (ret_val)
                                return ret_val;
                }

                /* Try once more */
                ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
                                                      100000, &link);
                if (ret_val)
                        return ret_val;
        }

        ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
        if (ret_val)
                return ret_val;

        /* Resetting the phy means we need to verify the TX_CLK corresponds
         * to the link speed.  10Mbps -> 2.5MHz, else 25MHz.
         */
        phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
        if (hw->mac.forced_speed_duplex & E1000_ALL_10_SPEED)
                phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5;
        else
                phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25;

        /* In addition, we must re-enable CRS on Tx for both half and full
         * duplex.
         */
        phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
        ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data);

        return ret_val;
}

/**
 *  e1000_get_cable_length_80003es2lan - Set approximate cable length
 *  @hw: pointer to the HW structure
 *
 *  Find the approximate cable length as measured by the GG82563 PHY.
 *  This is a function pointer entry point called by the phy module.
 **/
static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw)
{
        struct e1000_phy_info *phy = &hw->phy;
        s32 ret_val;
        u16 phy_data, index;

        ret_val = e1e_rphy(hw, GG82563_PHY_DSP_DISTANCE, &phy_data);
        if (ret_val)
                return ret_val;

        index = phy_data & GG82563_DSPD_CABLE_LENGTH;

        if (index >= GG82563_CABLE_LENGTH_TABLE_SIZE - 5)
                return -E1000_ERR_PHY;

        phy->min_cable_length = e1000_gg82563_cable_length_table[index];
        phy->max_cable_length = e1000_gg82563_cable_length_table[index + 5];

        phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2;

        return 0;
}

/**
 *  e1000_get_link_up_info_80003es2lan - Report speed and duplex
 *  @hw: pointer to the HW structure
 *  @speed: pointer to speed buffer
 *  @duplex: pointer to duplex buffer
 *
 *  Retrieve the current speed and duplex configuration.
 **/
static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed,
                                              u16 *duplex)
{
        s32 ret_val;

        if (hw->phy.media_type == e1000_media_type_copper) {
                ret_val = e1000e_get_speed_and_duplex_copper(hw, speed, duplex);
                hw->phy.ops.cfg_on_link_up(hw);
        } else {
                ret_val = e1000e_get_speed_and_duplex_fiber_serdes(hw,
                                                                   speed,
                                                                   duplex);
        }

        return ret_val;
}

/**
 *  e1000_reset_hw_80003es2lan - Reset the ESB2 controller
 *  @hw: pointer to the HW structure
 *
 *  Perform a global reset to the ESB2 controller.
 **/
static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
{
        u32 ctrl;
        s32 ret_val;
        u16 kum_reg_data;

        /* Prevent the PCI-E bus from sticking if there is no TLP connection
         * on the last TLP read/write transaction when MAC is reset.
         */
        ret_val = e1000e_disable_pcie_master(hw);
        if (ret_val)
                e_dbg("PCI-E Master disable polling has failed.\n");

        e_dbg("Masking off all interrupts\n");
        ew32(IMC, 0xffffffff);

        ew32(RCTL, 0);
        ew32(TCTL, E1000_TCTL_PSP);
        e1e_flush();

        usleep_range(10000, 11000);

        ctrl = er32(CTRL);

        ret_val = e1000_acquire_phy_80003es2lan(hw);
        if (ret_val)
                return ret_val;

        e_dbg("Issuing a global reset to MAC\n");
        ew32(CTRL, ctrl | E1000_CTRL_RST);
        e1000_release_phy_80003es2lan(hw);

        /* Disable IBIST slave mode (far-end loopback) */
        ret_val =
            e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
                                            &kum_reg_data);
        if (!ret_val) {
                kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE;
                ret_val = e1000_write_kmrn_reg_80003es2lan(hw,
                                                 E1000_KMRNCTRLSTA_INBAND_PARAM,
                                                 kum_reg_data);
                if (ret_val)
                        e_dbg("Error disabling far-end loopback\n");
        } else {
                e_dbg("Error disabling far-end loopback\n");
        }

        ret_val = e1000e_get_auto_rd_done(hw);
        if (ret_val)
                /* We don't want to continue accessing MAC registers. */
                return ret_val;

        /* Clear any pending interrupt events. */
        ew32(IMC, 0xffffffff);
        er32(ICR);

        return e1000_check_alt_mac_addr_generic(hw);
}

/**
 *  e1000_init_hw_80003es2lan - Initialize the ESB2 controller
 *  @hw: pointer to the HW structure
 *
 *  Initialize the hw bits, LED, VFTA, MTA, link and hw counters.
 **/
static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
{
        struct e1000_mac_info *mac = &hw->mac;
        u32 reg_data;
        s32 ret_val;
        u16 kum_reg_data;
        u16 i;

        e1000_initialize_hw_bits_80003es2lan(hw);

        /* Initialize identification LED */
        ret_val = mac->ops.id_led_init(hw);
        /* An error is not fatal and we should not stop init due to this */
        if (ret_val)
                e_dbg("Error initializing identification LED\n");

        /* Disabling VLAN filtering */
        e_dbg("Initializing the IEEE VLAN\n");
        mac->ops.clear_vfta(hw);

        /* Setup the receive address. */
        e1000e_init_rx_addrs(hw, mac->rar_entry_count);

        /* Zero out the Multicast HASH table */
        e_dbg("Zeroing the MTA\n");
        for (i = 0; i < mac->mta_reg_count; i++)
                E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);

        /* Setup link and flow control */
        ret_val = mac->ops.setup_link(hw);
        if (ret_val)
                return ret_val;

        /* Disable IBIST slave mode (far-end loopback) */
        ret_val =
            e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
                                            &kum_reg_data);
        if (!ret_val) {
                kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE;
                ret_val = e1000_write_kmrn_reg_80003es2lan(hw,
                                                 E1000_KMRNCTRLSTA_INBAND_PARAM,
                                                 kum_reg_data);
                if (ret_val)
                        e_dbg("Error disabling far-end loopback\n");
        } else {
                e_dbg("Error disabling far-end loopback\n");
        }

        /* Set the transmit descriptor write-back policy */
        reg_data = er32(TXDCTL(0));
        reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) |
                    E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC);
        ew32(TXDCTL(0), reg_data);

        /* ...for both queues. */
        reg_data = er32(TXDCTL(1));
        reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) |
                    E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC);
        ew32(TXDCTL(1), reg_data);

        /* Enable retransmit on late collisions */
        reg_data = er32(TCTL);
        reg_data |= E1000_TCTL_RTLC;
        ew32(TCTL, reg_data);

        /* Configure Gigabit Carry Extend Padding */
        reg_data = er32(TCTL_EXT);
        reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
        reg_data |= DEFAULT_TCTL_EXT_GCEX_80003ES2LAN;
        ew32(TCTL_EXT, reg_data);

        /* Configure Transmit Inter-Packet Gap */
        reg_data = er32(TIPG);
        reg_data &= ~E1000_TIPG_IPGT_MASK;
        reg_data |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
        ew32(TIPG, reg_data);

        reg_data = E1000_READ_REG_ARRAY(hw, E1000_FFLT, 0x0001);
        reg_data &= ~0x00100000;
        E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data);

        /* default to true to enable the MDIC W/A */
        hw->dev_spec.e80003es2lan.mdic_wa_enable = true;

        ret_val =
            e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET >>
                                            E1000_KMRNCTRLSTA_OFFSET_SHIFT, &i);
        if (!ret_val) {
                if ((i & E1000_KMRNCTRLSTA_OPMODE_MASK) ==
                    E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO)
                        hw->dev_spec.e80003es2lan.mdic_wa_enable = false;
        }

        /* Clear all of the statistics registers (clear on read).  It is
         * important that we do this after we have tried to establish link
         * because the symbol error count will increment wildly if there
         * is no link.
         */
        e1000_clear_hw_cntrs_80003es2lan(hw);

        return ret_val;
}

/**
 *  e1000_initialize_hw_bits_80003es2lan - Init hw bits of ESB2
 *  @hw: pointer to the HW structure
 *
 *  Initializes required hardware-dependent bits needed for normal operation.
 **/
static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw)
{
        u32 reg;

        /* Transmit Descriptor Control 0 */
        reg = er32(TXDCTL(0));
        reg |= BIT(22);
        ew32(TXDCTL(0), reg);

        /* Transmit Descriptor Control 1 */
        reg = er32(TXDCTL(1));
        reg |= BIT(22);
        ew32(TXDCTL(1), reg);

        /* Transmit Arbitration Control 0 */
        reg = er32(TARC(0));
        reg &= ~(0xF << 27);    /* 30:27 */
        if (hw->phy.media_type != e1000_media_type_copper)
                reg &= ~BIT(20);
        ew32(TARC(0), reg);

        /* Transmit Arbitration Control 1 */
        reg = er32(TARC(1));
        if (er32(TCTL) & E1000_TCTL_MULR)
                reg &= ~BIT(28);
        else
                reg |= BIT(28);
        ew32(TARC(1), reg);

        /* Disable IPv6 extension header parsing because some malformed
         * IPv6 headers can hang the Rx.
         */
        reg = er32(RFCTL);
        reg |= (E1000_RFCTL_IPV6_EX_DIS | E1000_RFCTL_NEW_IPV6_EXT_DIS);
        ew32(RFCTL, reg);
}

/**
 *  e1000_copper_link_setup_gg82563_80003es2lan - Configure GG82563 Link
 *  @hw: pointer to the HW structure
 *
 *  Setup some GG82563 PHY registers for obtaining link
 **/
static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
{
        struct e1000_phy_info *phy = &hw->phy;
        s32 ret_val;
        u32 reg;
        u16 data;

        ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &data);
        if (ret_val)
                return ret_val;

        data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
        /* Use 25MHz for both link down and 1000Base-T for Tx clock. */
        data |= GG82563_MSCR_TX_CLK_1000MBPS_25;

        ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, data);
        if (ret_val)
                return ret_val;

        /* Options:
         *   MDI/MDI-X = 0 (default)
         *   0 - Auto for all speeds
         *   1 - MDI mode
         *   2 - MDI-X mode
         *   3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
         */
        ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL, &data);
        if (ret_val)
                return ret_val;

        data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;

        switch (phy->mdix) {
        case 1:
                data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
                break;
        case 2:
                data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
                break;
        case 0:
        default:
                data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
                break;
        }

        /* Options:
         *   disable_polarity_correction = 0 (default)
         *       Automatic Correction for Reversed Cable Polarity
         *   0 - Disabled
         *   1 - Enabled
         */
        data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
        if (phy->disable_polarity_correction)
                data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE;

        ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, data);
        if (ret_val)
                return ret_val;

        /* SW Reset the PHY so all changes take effect */
        ret_val = hw->phy.ops.commit(hw);
        if (ret_val) {
                e_dbg("Error Resetting the PHY\n");
                return ret_val;
        }

        /* Bypass Rx and Tx FIFO's */
        reg = E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL;
        data = (E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS |
                E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS);
        ret_val = e1000_write_kmrn_reg_80003es2lan(hw, reg, data);
        if (ret_val)
                return ret_val;

        reg = E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE;
        ret_val = e1000_read_kmrn_reg_80003es2lan(hw, reg, &data);
        if (ret_val)
                return ret_val;
        data |= E1000_KMRNCTRLSTA_OPMODE_E_IDLE;
        ret_val = e1000_write_kmrn_reg_80003es2lan(hw, reg, data);
        if (ret_val)
                return ret_val;

        ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL_2, &data);
        if (ret_val)
                return ret_val;

        data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
        ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL_2, data);
        if (ret_val)
                return ret_val;

        reg = er32(CTRL_EXT);
        reg &= ~E1000_CTRL_EXT_LINK_MODE_MASK;
        ew32(CTRL_EXT, reg);

        ret_val = e1e_rphy(hw, GG82563_PHY_PWR_MGMT_CTRL, &data);
        if (ret_val)
                return ret_val;

        /* Do not init these registers when the HW is in IAMT mode, since the
         * firmware will have already initialized them.  We only initialize
         * them if the HW is not in IAMT mode.
         */
        if (!hw->mac.ops.check_mng_mode(hw)) {
                /* Enable Electrical Idle on the PHY */
                data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
                ret_val = e1e_wphy(hw, GG82563_PHY_PWR_MGMT_CTRL, data);
                if (ret_val)
                        return ret_val;

                ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &data);
                if (ret_val)
                        return ret_val;

                data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
                ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, data);
                if (ret_val)
                        return ret_val;
        }

        /* Workaround: Disable padding in Kumeran interface in the MAC
         * and in the PHY to avoid CRC errors.
         */
        ret_val = e1e_rphy(hw, GG82563_PHY_INBAND_CTRL, &data);
        if (ret_val)
                return ret_val;

        data |= GG82563_ICR_DIS_PADDING;
        ret_val = e1e_wphy(hw, GG82563_PHY_INBAND_CTRL, data);
        if (ret_val)
                return ret_val;

        return 0;
}

/**
 *  e1000_setup_copper_link_80003es2lan - Setup Copper Link for ESB2
 *  @hw: pointer to the HW structure
 *
 *  Essentially a wrapper for setting up all things "copper" related.
 *  This is a function pointer entry point called by the mac module.
 **/
static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw)
{
        u32 ctrl;
        s32 ret_val;
        u16 reg_data;

        ctrl = er32(CTRL);
        ctrl |= E1000_CTRL_SLU;
        ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
        ew32(CTRL, ctrl);

        /* Set the mac to wait the maximum time between each
         * iteration and increase the max iterations when
         * polling the phy; this fixes erroneous timeouts at 10Mbps.
         */
        ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 4),
                                                   0xFFFF);
        if (ret_val)
                return ret_val;
        ret_val = e1000_read_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9),
                                                  &reg_data);
        if (ret_val)
                return ret_val;
        reg_data |= 0x3F;
        ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9),
                                                   reg_data);
        if (ret_val)
                return ret_val;
        ret_val =
            e1000_read_kmrn_reg_80003es2lan(hw,
                                            E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
                                            &reg_data);
        if (ret_val)
                return ret_val;
        reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING;
        ret_val =
            e1000_write_kmrn_reg_80003es2lan(hw,
                                             E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
                                             reg_data);
        if (ret_val)
                return ret_val;

        ret_val = e1000_copper_link_setup_gg82563_80003es2lan(hw);
        if (ret_val)
                return ret_val;

        return e1000e_setup_copper_link(hw);
}

/**
 *  e1000_cfg_on_link_up_80003es2lan - es2 link configuration after link-up
 *  @hw: pointer to the HW structure
 *
 *  Configure the KMRN interface by applying last minute quirks for
 *  10/100 operation.
 **/
static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw)
{
        s32 ret_val = 0;
        u16 speed;
        u16 duplex;

        if (hw->phy.media_type == e1000_media_type_copper) {
                ret_val = e1000e_get_speed_and_duplex_copper(hw, &speed,
                                                             &duplex);
                if (ret_val)
                        return ret_val;

                if (speed == SPEED_1000)
                        ret_val = e1000_cfg_kmrn_1000_80003es2lan(hw);
                else
                        ret_val = e1000_cfg_kmrn_10_100_80003es2lan(hw, duplex);
        }

        return ret_val;
}

/**
 *  e1000_cfg_kmrn_10_100_80003es2lan - Apply "quirks" for 10/100 operation
 *  @hw: pointer to the HW structure
 *  @duplex: current duplex setting
 *
 *  Configure the KMRN interface by applying last minute quirks for
 *  10/100 operation.
 **/
static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex)
{
        s32 ret_val;
        u32 tipg;
        u32 i = 0;
        u16 reg_data, reg_data2;

        reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT;
        ret_val =
            e1000_write_kmrn_reg_80003es2lan(hw,
                                             E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
                                             reg_data);
        if (ret_val)
                return ret_val;

        /* Configure Transmit Inter-Packet Gap */
        tipg = er32(TIPG);
        tipg &= ~E1000_TIPG_IPGT_MASK;
        tipg |= DEFAULT_TIPG_IPGT_10_100_80003ES2LAN;
        ew32(TIPG, tipg);

        do {
                ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
                if (ret_val)
                        return ret_val;

                ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data2);
                if (ret_val)
                        return ret_val;
                i++;
        } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));

        if (duplex == HALF_DUPLEX)
                reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
        else
                reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;

        return e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
}

/**
 *  e1000_cfg_kmrn_1000_80003es2lan - Apply "quirks" for gigabit operation
 *  @hw: pointer to the HW structure
 *
 *  Configure the KMRN interface by applying last minute quirks for
 *  gigabit operation.
 **/
static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw)
{
        s32 ret_val;
        u16 reg_data, reg_data2;
        u32 tipg;
        u32 i = 0;

        reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT;
        ret_val =
            e1000_write_kmrn_reg_80003es2lan(hw,
                                             E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
                                             reg_data);
        if (ret_val)
                return ret_val;

        /* Configure Transmit Inter-Packet Gap */
        tipg = er32(TIPG);
        tipg &= ~E1000_TIPG_IPGT_MASK;
        tipg |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
        ew32(TIPG, tipg);

        do {
                ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
                if (ret_val)
                        return ret_val;

                ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data2);
                if (ret_val)
                        return ret_val;
                i++;
        } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));

        reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;

        return e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
}

/**
 *  e1000_read_kmrn_reg_80003es2lan - Read kumeran register
 *  @hw: pointer to the HW structure
 *  @offset: register offset to be read
 *  @data: pointer to the read data
 *
 *  Acquire semaphore, then read the PHY register at offset
 *  using the kumeran interface.  The information retrieved is stored in data.
 *  Release the semaphore before exiting.
 **/
static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
                                           u16 *data)
{
        u32 kmrnctrlsta;
        s32 ret_val;

        ret_val = e1000_acquire_mac_csr_80003es2lan(hw);
        if (ret_val)
                return ret_val;

        kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
                       E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN;
        ew32(KMRNCTRLSTA, kmrnctrlsta);
        e1e_flush();

        udelay(2);

        kmrnctrlsta = er32(KMRNCTRLSTA);
        *data = (u16)kmrnctrlsta;

        e1000_release_mac_csr_80003es2lan(hw);

        return ret_val;
}

/**
 *  e1000_write_kmrn_reg_80003es2lan - Write kumeran register
 *  @hw: pointer to the HW structure
 *  @offset: register offset to write to
 *  @data: data to write at register offset
 *
 *  Acquire semaphore, then write the data to PHY register
 *  at the offset using the kumeran interface.  Release semaphore
 *  before exiting.
 **/
static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
                                            u16 data)
{
        u32 kmrnctrlsta;
        s32 ret_val;

        ret_val = e1000_acquire_mac_csr_80003es2lan(hw);
        if (ret_val)
                return ret_val;

        kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
                       E1000_KMRNCTRLSTA_OFFSET) | data;
        ew32(KMRNCTRLSTA, kmrnctrlsta);
        e1e_flush();

        udelay(2);

        e1000_release_mac_csr_80003es2lan(hw);

        return ret_val;
}

/**
 *  e1000_read_mac_addr_80003es2lan - Read device MAC address
 *  @hw: pointer to the HW structure
 **/
static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw)
{
        s32 ret_val;

        /* If there's an alternate MAC address place it in RAR0
         * so that it will override the Si installed default perm
         * address.
         */
        ret_val = e1000_check_alt_mac_addr_generic(hw);
        if (ret_val)
                return ret_val;

        return e1000_read_mac_addr_generic(hw);
}

/**
 * e1000_power_down_phy_copper_80003es2lan - Remove link during PHY power down
 * @hw: pointer to the HW structure
 *
 * In the case of a PHY power down to save power, or to turn off link during a
 * driver unload, or wake on lan is not enabled, remove the link.
 **/
static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw)
{
        /* If the management interface is not enabled, then power down */
        if (!(hw->mac.ops.check_mng_mode(hw) ||
              hw->phy.ops.check_reset_block(hw)))
                e1000_power_down_phy_copper(hw);
}

/**
 *  e1000_clear_hw_cntrs_80003es2lan - Clear device specific hardware counters
 *  @hw: pointer to the HW structure
 *
 *  Clears the hardware counters by reading the counter registers.
 **/
static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw)
{
        e1000e_clear_hw_cntrs_base(hw);

        er32(PRC64);
        er32(PRC127);
        er32(PRC255);
        er32(PRC511);
        er32(PRC1023);
        er32(PRC1522);
        er32(PTC64);
        er32(PTC127);
        er32(PTC255);
        er32(PTC511);
        er32(PTC1023);
        er32(PTC1522);

        er32(ALGNERRC);
        er32(RXERRC);
        er32(TNCRS);
        er32(CEXTERR);
        er32(TSCTC);
        er32(TSCTFC);

        er32(MGTPRC);
        er32(MGTPDC);
        er32(MGTPTC);

        er32(IAC);
        er32(ICRXOC);

        er32(ICRXPTC);
        er32(ICRXATC);
        er32(ICTXPTC);
        er32(ICTXATC);
        er32(ICTXQEC);
        er32(ICTXQMTC);
        er32(ICRXDMTC);
}

static const struct e1000_mac_operations es2_mac_ops = {
        .read_mac_addr          = e1000_read_mac_addr_80003es2lan,
        .id_led_init            = e1000e_id_led_init_generic,
        .blink_led              = e1000e_blink_led_generic,
        .check_mng_mode         = e1000e_check_mng_mode_generic,
        /* check_for_link dependent on media type */
        .cleanup_led            = e1000e_cleanup_led_generic,
        .clear_hw_cntrs         = e1000_clear_hw_cntrs_80003es2lan,
        .get_bus_info           = e1000e_get_bus_info_pcie,
        .set_lan_id             = e1000_set_lan_id_multi_port_pcie,
        .get_link_up_info       = e1000_get_link_up_info_80003es2lan,
        .led_on                 = e1000e_led_on_generic,
        .led_off                = e1000e_led_off_generic,
        .update_mc_addr_list    = e1000e_update_mc_addr_list_generic,
        .write_vfta             = e1000_write_vfta_generic,
        .clear_vfta             = e1000_clear_vfta_generic,
        .reset_hw               = e1000_reset_hw_80003es2lan,
        .init_hw                = e1000_init_hw_80003es2lan,
        .setup_link             = e1000e_setup_link_generic,
        /* setup_physical_interface dependent on media type */
        .setup_led              = e1000e_setup_led_generic,
        .config_collision_dist  = e1000e_config_collision_dist_generic,
        .rar_set                = e1000e_rar_set_generic,
        .rar_get_count          = e1000e_rar_get_count_generic,
};

static const struct e1000_phy_operations es2_phy_ops = {
        .acquire                = e1000_acquire_phy_80003es2lan,
        .check_polarity         = e1000_check_polarity_m88,
        .check_reset_block      = e1000e_check_reset_block_generic,
        .commit                 = e1000e_phy_sw_reset,
        .force_speed_duplex     = e1000_phy_force_speed_duplex_80003es2lan,
        .get_cfg_done           = e1000_get_cfg_done_80003es2lan,
        .get_cable_length       = e1000_get_cable_length_80003es2lan,
        .get_info               = e1000e_get_phy_info_m88,
        .read_reg               = e1000_read_phy_reg_gg82563_80003es2lan,
        .release                = e1000_release_phy_80003es2lan,
        .reset                  = e1000e_phy_hw_reset_generic,
        .set_d0_lplu_state      = NULL,
        .set_d3_lplu_state      = e1000e_set_d3_lplu_state,
        .write_reg              = e1000_write_phy_reg_gg82563_80003es2lan,
        .cfg_on_link_up         = e1000_cfg_on_link_up_80003es2lan,
};

static const struct e1000_nvm_operations es2_nvm_ops = {
        .acquire                = e1000_acquire_nvm_80003es2lan,
        .read                   = e1000e_read_nvm_eerd,
        .release                = e1000_release_nvm_80003es2lan,
        .reload                 = e1000e_reload_nvm_generic,
        .update                 = e1000e_update_nvm_checksum_generic,
        .valid_led_default      = e1000e_valid_led_default,
        .validate               = e1000e_validate_nvm_checksum_generic,
        .write                  = e1000_write_nvm_80003es2lan,
};

const struct e1000_info e1000_es2_info = {
        .mac                    = e1000_80003es2lan,
        .flags                  = FLAG_HAS_HW_VLAN_FILTER
                                  | FLAG_HAS_JUMBO_FRAMES
                                  | FLAG_HAS_WOL
                                  | FLAG_APME_IN_CTRL3
                                  | FLAG_HAS_CTRLEXT_ON_LOAD
                                  | FLAG_RX_NEEDS_RESTART /* errata */
                                  | FLAG_TARC_SET_BIT_ZERO /* errata */
                                  | FLAG_APME_CHECK_PORT_B
                                  | FLAG_DISABLE_FC_PAUSE_TIME, /* errata */
        .flags2                 = FLAG2_DMA_BURST,
        .pba                    = 38,
        .max_hw_frame_size      = DEFAULT_JUMBO,
        .get_variants           = e1000_get_variants_80003es2lan,
        .mac_ops                = &es2_mac_ops,
        .phy_ops                = &es2_phy_ops,
        .nvm_ops                = &es2_nvm_ops,
};