linux/drivers/input/touchscreen/stmfts.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0
   2// STMicroelectronics FTS Touchscreen device driver
   3//
   4// Copyright (c) 2017 Samsung Electronics Co., Ltd.
   5// Copyright (c) 2017 Andi Shyti <andi@etezian.org>
   6
   7#include <linux/delay.h>
   8#include <linux/i2c.h>
   9#include <linux/input/mt.h>
  10#include <linux/input/touchscreen.h>
  11#include <linux/interrupt.h>
  12#include <linux/irq.h>
  13#include <linux/leds.h>
  14#include <linux/module.h>
  15#include <linux/pm_runtime.h>
  16#include <linux/regulator/consumer.h>
  17
  18/* I2C commands */
  19#define STMFTS_READ_INFO                        0x80
  20#define STMFTS_READ_STATUS                      0x84
  21#define STMFTS_READ_ONE_EVENT                   0x85
  22#define STMFTS_READ_ALL_EVENT                   0x86
  23#define STMFTS_LATEST_EVENT                     0x87
  24#define STMFTS_SLEEP_IN                         0x90
  25#define STMFTS_SLEEP_OUT                        0x91
  26#define STMFTS_MS_MT_SENSE_OFF                  0x92
  27#define STMFTS_MS_MT_SENSE_ON                   0x93
  28#define STMFTS_SS_HOVER_SENSE_OFF               0x94
  29#define STMFTS_SS_HOVER_SENSE_ON                0x95
  30#define STMFTS_MS_KEY_SENSE_OFF                 0x9a
  31#define STMFTS_MS_KEY_SENSE_ON                  0x9b
  32#define STMFTS_SYSTEM_RESET                     0xa0
  33#define STMFTS_CLEAR_EVENT_STACK                0xa1
  34#define STMFTS_FULL_FORCE_CALIBRATION           0xa2
  35#define STMFTS_MS_CX_TUNING                     0xa3
  36#define STMFTS_SS_CX_TUNING                     0xa4
  37
  38/* events */
  39#define STMFTS_EV_NO_EVENT                      0x00
  40#define STMFTS_EV_MULTI_TOUCH_DETECTED          0x02
  41#define STMFTS_EV_MULTI_TOUCH_ENTER             0x03
  42#define STMFTS_EV_MULTI_TOUCH_LEAVE             0x04
  43#define STMFTS_EV_MULTI_TOUCH_MOTION            0x05
  44#define STMFTS_EV_HOVER_ENTER                   0x07
  45#define STMFTS_EV_HOVER_LEAVE                   0x08
  46#define STMFTS_EV_HOVER_MOTION                  0x09
  47#define STMFTS_EV_KEY_STATUS                    0x0e
  48#define STMFTS_EV_ERROR                         0x0f
  49#define STMFTS_EV_CONTROLLER_READY              0x10
  50#define STMFTS_EV_SLEEP_OUT_CONTROLLER_READY    0x11
  51#define STMFTS_EV_STATUS                        0x16
  52#define STMFTS_EV_DEBUG                         0xdb
  53
  54/* multi touch related event masks */
  55#define STMFTS_MASK_EVENT_ID                    0x0f
  56#define STMFTS_MASK_TOUCH_ID                    0xf0
  57#define STMFTS_MASK_LEFT_EVENT                  0x0f
  58#define STMFTS_MASK_X_MSB                       0x0f
  59#define STMFTS_MASK_Y_LSB                       0xf0
  60
  61/* key related event masks */
  62#define STMFTS_MASK_KEY_NO_TOUCH                0x00
  63#define STMFTS_MASK_KEY_MENU                    0x01
  64#define STMFTS_MASK_KEY_BACK                    0x02
  65
  66#define STMFTS_EVENT_SIZE       8
  67#define STMFTS_STACK_DEPTH      32
  68#define STMFTS_DATA_MAX_SIZE    (STMFTS_EVENT_SIZE * STMFTS_STACK_DEPTH)
  69#define STMFTS_MAX_FINGERS      10
  70#define STMFTS_DEV_NAME         "stmfts"
  71
  72enum stmfts_regulators {
  73        STMFTS_REGULATOR_VDD,
  74        STMFTS_REGULATOR_AVDD,
  75};
  76
  77struct stmfts_data {
  78        struct i2c_client *client;
  79        struct input_dev *input;
  80        struct led_classdev led_cdev;
  81        struct mutex mutex;
  82
  83        struct touchscreen_properties prop;
  84
  85        struct regulator_bulk_data regulators[2];
  86
  87        /*
  88         * Presence of ledvdd will be used also to check
  89         * whether the LED is supported.
  90         */
  91        struct regulator *ledvdd;
  92
  93        u16 chip_id;
  94        u8 chip_ver;
  95        u16 fw_ver;
  96        u8 config_id;
  97        u8 config_ver;
  98
  99        u8 data[STMFTS_DATA_MAX_SIZE];
 100
 101        struct completion cmd_done;
 102
 103        bool use_key;
 104        bool led_status;
 105        bool hover_enabled;
 106        bool running;
 107};
 108
 109static int stmfts_brightness_set(struct led_classdev *led_cdev,
 110                                        enum led_brightness value)
 111{
 112        struct stmfts_data *sdata = container_of(led_cdev,
 113                                        struct stmfts_data, led_cdev);
 114        int err;
 115
 116        if (value != sdata->led_status && sdata->ledvdd) {
 117                if (!value) {
 118                        regulator_disable(sdata->ledvdd);
 119                } else {
 120                        err = regulator_enable(sdata->ledvdd);
 121                        if (err) {
 122                                dev_warn(&sdata->client->dev,
 123                                         "failed to disable ledvdd regulator: %d\n",
 124                                         err);
 125                                return err;
 126                        }
 127                }
 128                sdata->led_status = value;
 129        }
 130
 131        return 0;
 132}
 133
 134static enum led_brightness stmfts_brightness_get(struct led_classdev *led_cdev)
 135{
 136        struct stmfts_data *sdata = container_of(led_cdev,
 137                                                struct stmfts_data, led_cdev);
 138
 139        return !!regulator_is_enabled(sdata->ledvdd);
 140}
 141
 142/*
 143 * We can't simply use i2c_smbus_read_i2c_block_data because we
 144 * need to read more than 255 bytes (
 145 */
 146static int stmfts_read_events(struct stmfts_data *sdata)
 147{
 148        u8 cmd = STMFTS_READ_ALL_EVENT;
 149        struct i2c_msg msgs[2] = {
 150                {
 151                        .addr   = sdata->client->addr,
 152                        .len    = 1,
 153                        .buf    = &cmd,
 154                },
 155                {
 156                        .addr   = sdata->client->addr,
 157                        .flags  = I2C_M_RD,
 158                        .len    = STMFTS_DATA_MAX_SIZE,
 159                        .buf    = sdata->data,
 160                },
 161        };
 162        int ret;
 163
 164        ret = i2c_transfer(sdata->client->adapter, msgs, ARRAY_SIZE(msgs));
 165        if (ret < 0)
 166                return ret;
 167
 168        return ret == ARRAY_SIZE(msgs) ? 0 : -EIO;
 169}
 170
 171static void stmfts_report_contact_event(struct stmfts_data *sdata,
 172                                        const u8 event[])
 173{
 174        u8 slot_id = (event[0] & STMFTS_MASK_TOUCH_ID) >> 4;
 175        u16 x = event[1] | ((event[2] & STMFTS_MASK_X_MSB) << 8);
 176        u16 y = (event[2] >> 4) | (event[3] << 4);
 177        u8 maj = event[4];
 178        u8 min = event[5];
 179        u8 orientation = event[6];
 180        u8 area = event[7];
 181
 182        input_mt_slot(sdata->input, slot_id);
 183
 184        input_mt_report_slot_state(sdata->input, MT_TOOL_FINGER, true);
 185        input_report_abs(sdata->input, ABS_MT_POSITION_X, x);
 186        input_report_abs(sdata->input, ABS_MT_POSITION_Y, y);
 187        input_report_abs(sdata->input, ABS_MT_TOUCH_MAJOR, maj);
 188        input_report_abs(sdata->input, ABS_MT_TOUCH_MINOR, min);
 189        input_report_abs(sdata->input, ABS_MT_PRESSURE, area);
 190        input_report_abs(sdata->input, ABS_MT_ORIENTATION, orientation);
 191
 192        input_sync(sdata->input);
 193}
 194
 195static void stmfts_report_contact_release(struct stmfts_data *sdata,
 196                                          const u8 event[])
 197{
 198        u8 slot_id = (event[0] & STMFTS_MASK_TOUCH_ID) >> 4;
 199
 200        input_mt_slot(sdata->input, slot_id);
 201        input_mt_report_slot_inactive(sdata->input);
 202
 203        input_sync(sdata->input);
 204}
 205
 206static void stmfts_report_hover_event(struct stmfts_data *sdata,
 207                                      const u8 event[])
 208{
 209        u16 x = (event[2] << 4) | (event[4] >> 4);
 210        u16 y = (event[3] << 4) | (event[4] & STMFTS_MASK_Y_LSB);
 211        u8 z = event[5];
 212
 213        input_report_abs(sdata->input, ABS_X, x);
 214        input_report_abs(sdata->input, ABS_Y, y);
 215        input_report_abs(sdata->input, ABS_DISTANCE, z);
 216
 217        input_sync(sdata->input);
 218}
 219
 220static void stmfts_report_key_event(struct stmfts_data *sdata, const u8 event[])
 221{
 222        switch (event[2]) {
 223        case 0:
 224                input_report_key(sdata->input, KEY_BACK, 0);
 225                input_report_key(sdata->input, KEY_MENU, 0);
 226                break;
 227
 228        case STMFTS_MASK_KEY_BACK:
 229                input_report_key(sdata->input, KEY_BACK, 1);
 230                break;
 231
 232        case STMFTS_MASK_KEY_MENU:
 233                input_report_key(sdata->input, KEY_MENU, 1);
 234                break;
 235
 236        default:
 237                dev_warn(&sdata->client->dev,
 238                         "unknown key event: %#02x\n", event[2]);
 239                break;
 240        }
 241
 242        input_sync(sdata->input);
 243}
 244
 245static void stmfts_parse_events(struct stmfts_data *sdata)
 246{
 247        int i;
 248
 249        for (i = 0; i < STMFTS_STACK_DEPTH; i++) {
 250                u8 *event = &sdata->data[i * STMFTS_EVENT_SIZE];
 251
 252                switch (event[0]) {
 253
 254                case STMFTS_EV_CONTROLLER_READY:
 255                case STMFTS_EV_SLEEP_OUT_CONTROLLER_READY:
 256                case STMFTS_EV_STATUS:
 257                        complete(&sdata->cmd_done);
 258                        fallthrough;
 259
 260                case STMFTS_EV_NO_EVENT:
 261                case STMFTS_EV_DEBUG:
 262                        return;
 263                }
 264
 265                switch (event[0] & STMFTS_MASK_EVENT_ID) {
 266
 267                case STMFTS_EV_MULTI_TOUCH_ENTER:
 268                case STMFTS_EV_MULTI_TOUCH_MOTION:
 269                        stmfts_report_contact_event(sdata, event);
 270                        break;
 271
 272                case STMFTS_EV_MULTI_TOUCH_LEAVE:
 273                        stmfts_report_contact_release(sdata, event);
 274                        break;
 275
 276                case STMFTS_EV_HOVER_ENTER:
 277                case STMFTS_EV_HOVER_LEAVE:
 278                case STMFTS_EV_HOVER_MOTION:
 279                        stmfts_report_hover_event(sdata, event);
 280                        break;
 281
 282                case STMFTS_EV_KEY_STATUS:
 283                        stmfts_report_key_event(sdata, event);
 284                        break;
 285
 286                case STMFTS_EV_ERROR:
 287                        dev_warn(&sdata->client->dev,
 288                                        "error code: 0x%x%x%x%x%x%x",
 289                                        event[6], event[5], event[4],
 290                                        event[3], event[2], event[1]);
 291                        break;
 292
 293                default:
 294                        dev_err(&sdata->client->dev,
 295                                "unknown event %#02x\n", event[0]);
 296                }
 297        }
 298}
 299
 300static irqreturn_t stmfts_irq_handler(int irq, void *dev)
 301{
 302        struct stmfts_data *sdata = dev;
 303        int err;
 304
 305        mutex_lock(&sdata->mutex);
 306
 307        err = stmfts_read_events(sdata);
 308        if (unlikely(err))
 309                dev_err(&sdata->client->dev,
 310                        "failed to read events: %d\n", err);
 311        else
 312                stmfts_parse_events(sdata);
 313
 314        mutex_unlock(&sdata->mutex);
 315        return IRQ_HANDLED;
 316}
 317
 318static int stmfts_command(struct stmfts_data *sdata, const u8 cmd)
 319{
 320        int err;
 321
 322        reinit_completion(&sdata->cmd_done);
 323
 324        err = i2c_smbus_write_byte(sdata->client, cmd);
 325        if (err)
 326                return err;
 327
 328        if (!wait_for_completion_timeout(&sdata->cmd_done,
 329                                         msecs_to_jiffies(1000)))
 330                return -ETIMEDOUT;
 331
 332        return 0;
 333}
 334
 335static int stmfts_input_open(struct input_dev *dev)
 336{
 337        struct stmfts_data *sdata = input_get_drvdata(dev);
 338        int err;
 339
 340        err = pm_runtime_get_sync(&sdata->client->dev);
 341        if (err < 0)
 342                return err;
 343
 344        err = i2c_smbus_write_byte(sdata->client, STMFTS_MS_MT_SENSE_ON);
 345        if (err)
 346                return err;
 347
 348        mutex_lock(&sdata->mutex);
 349        sdata->running = true;
 350
 351        if (sdata->hover_enabled) {
 352                err = i2c_smbus_write_byte(sdata->client,
 353                                           STMFTS_SS_HOVER_SENSE_ON);
 354                if (err)
 355                        dev_warn(&sdata->client->dev,
 356                                 "failed to enable hover\n");
 357        }
 358        mutex_unlock(&sdata->mutex);
 359
 360        if (sdata->use_key) {
 361                err = i2c_smbus_write_byte(sdata->client,
 362                                           STMFTS_MS_KEY_SENSE_ON);
 363                if (err)
 364                        /* I can still use only the touch screen */
 365                        dev_warn(&sdata->client->dev,
 366                                 "failed to enable touchkey\n");
 367        }
 368
 369        return 0;
 370}
 371
 372static void stmfts_input_close(struct input_dev *dev)
 373{
 374        struct stmfts_data *sdata = input_get_drvdata(dev);
 375        int err;
 376
 377        err = i2c_smbus_write_byte(sdata->client, STMFTS_MS_MT_SENSE_OFF);
 378        if (err)
 379                dev_warn(&sdata->client->dev,
 380                         "failed to disable touchscreen: %d\n", err);
 381
 382        mutex_lock(&sdata->mutex);
 383
 384        sdata->running = false;
 385
 386        if (sdata->hover_enabled) {
 387                err = i2c_smbus_write_byte(sdata->client,
 388                                           STMFTS_SS_HOVER_SENSE_OFF);
 389                if (err)
 390                        dev_warn(&sdata->client->dev,
 391                                 "failed to disable hover: %d\n", err);
 392        }
 393        mutex_unlock(&sdata->mutex);
 394
 395        if (sdata->use_key) {
 396                err = i2c_smbus_write_byte(sdata->client,
 397                                           STMFTS_MS_KEY_SENSE_OFF);
 398                if (err)
 399                        dev_warn(&sdata->client->dev,
 400                                 "failed to disable touchkey: %d\n", err);
 401        }
 402
 403        pm_runtime_put_sync(&sdata->client->dev);
 404}
 405
 406static ssize_t stmfts_sysfs_chip_id(struct device *dev,
 407                                struct device_attribute *attr, char *buf)
 408{
 409        struct stmfts_data *sdata = dev_get_drvdata(dev);
 410
 411        return sprintf(buf, "%#x\n", sdata->chip_id);
 412}
 413
 414static ssize_t stmfts_sysfs_chip_version(struct device *dev,
 415                                struct device_attribute *attr, char *buf)
 416{
 417        struct stmfts_data *sdata = dev_get_drvdata(dev);
 418
 419        return sprintf(buf, "%u\n", sdata->chip_ver);
 420}
 421
 422static ssize_t stmfts_sysfs_fw_ver(struct device *dev,
 423                                struct device_attribute *attr, char *buf)
 424{
 425        struct stmfts_data *sdata = dev_get_drvdata(dev);
 426
 427        return sprintf(buf, "%u\n", sdata->fw_ver);
 428}
 429
 430static ssize_t stmfts_sysfs_config_id(struct device *dev,
 431                                struct device_attribute *attr, char *buf)
 432{
 433        struct stmfts_data *sdata = dev_get_drvdata(dev);
 434
 435        return sprintf(buf, "%#x\n", sdata->config_id);
 436}
 437
 438static ssize_t stmfts_sysfs_config_version(struct device *dev,
 439                                struct device_attribute *attr, char *buf)
 440{
 441        struct stmfts_data *sdata = dev_get_drvdata(dev);
 442
 443        return sprintf(buf, "%u\n", sdata->config_ver);
 444}
 445
 446static ssize_t stmfts_sysfs_read_status(struct device *dev,
 447                                struct device_attribute *attr, char *buf)
 448{
 449        struct stmfts_data *sdata = dev_get_drvdata(dev);
 450        u8 status[4];
 451        int err;
 452
 453        err = i2c_smbus_read_i2c_block_data(sdata->client, STMFTS_READ_STATUS,
 454                                            sizeof(status), status);
 455        if (err)
 456                return err;
 457
 458        return sprintf(buf, "%#02x\n", status[0]);
 459}
 460
 461static ssize_t stmfts_sysfs_hover_enable_read(struct device *dev,
 462                                struct device_attribute *attr, char *buf)
 463{
 464        struct stmfts_data *sdata = dev_get_drvdata(dev);
 465
 466        return sprintf(buf, "%u\n", sdata->hover_enabled);
 467}
 468
 469static ssize_t stmfts_sysfs_hover_enable_write(struct device *dev,
 470                                struct device_attribute *attr,
 471                                const char *buf, size_t len)
 472{
 473        struct stmfts_data *sdata = dev_get_drvdata(dev);
 474        unsigned long value;
 475        int err = 0;
 476
 477        if (kstrtoul(buf, 0, &value))
 478                return -EINVAL;
 479
 480        mutex_lock(&sdata->mutex);
 481
 482        if (value && sdata->hover_enabled)
 483                goto out;
 484
 485        if (sdata->running)
 486                err = i2c_smbus_write_byte(sdata->client,
 487                                           value ? STMFTS_SS_HOVER_SENSE_ON :
 488                                                   STMFTS_SS_HOVER_SENSE_OFF);
 489
 490        if (!err)
 491                sdata->hover_enabled = !!value;
 492
 493out:
 494        mutex_unlock(&sdata->mutex);
 495
 496        return len;
 497}
 498
 499static DEVICE_ATTR(chip_id, 0444, stmfts_sysfs_chip_id, NULL);
 500static DEVICE_ATTR(chip_version, 0444, stmfts_sysfs_chip_version, NULL);
 501static DEVICE_ATTR(fw_ver, 0444, stmfts_sysfs_fw_ver, NULL);
 502static DEVICE_ATTR(config_id, 0444, stmfts_sysfs_config_id, NULL);
 503static DEVICE_ATTR(config_version, 0444, stmfts_sysfs_config_version, NULL);
 504static DEVICE_ATTR(status, 0444, stmfts_sysfs_read_status, NULL);
 505static DEVICE_ATTR(hover_enable, 0644, stmfts_sysfs_hover_enable_read,
 506                                        stmfts_sysfs_hover_enable_write);
 507
 508static struct attribute *stmfts_sysfs_attrs[] = {
 509        &dev_attr_chip_id.attr,
 510        &dev_attr_chip_version.attr,
 511        &dev_attr_fw_ver.attr,
 512        &dev_attr_config_id.attr,
 513        &dev_attr_config_version.attr,
 514        &dev_attr_status.attr,
 515        &dev_attr_hover_enable.attr,
 516        NULL
 517};
 518
 519static struct attribute_group stmfts_attribute_group = {
 520        .attrs = stmfts_sysfs_attrs
 521};
 522
 523static int stmfts_power_on(struct stmfts_data *sdata)
 524{
 525        int err;
 526        u8 reg[8];
 527
 528        err = regulator_bulk_enable(ARRAY_SIZE(sdata->regulators),
 529                                    sdata->regulators);
 530        if (err)
 531                return err;
 532
 533        /*
 534         * The datasheet does not specify the power on time, but considering
 535         * that the reset time is < 10ms, I sleep 20ms to be sure
 536         */
 537        msleep(20);
 538
 539        err = i2c_smbus_read_i2c_block_data(sdata->client, STMFTS_READ_INFO,
 540                                            sizeof(reg), reg);
 541        if (err < 0)
 542                return err;
 543        if (err != sizeof(reg))
 544                return -EIO;
 545
 546        sdata->chip_id = be16_to_cpup((__be16 *)&reg[6]);
 547        sdata->chip_ver = reg[0];
 548        sdata->fw_ver = be16_to_cpup((__be16 *)&reg[2]);
 549        sdata->config_id = reg[4];
 550        sdata->config_ver = reg[5];
 551
 552        enable_irq(sdata->client->irq);
 553
 554        msleep(50);
 555
 556        err = stmfts_command(sdata, STMFTS_SYSTEM_RESET);
 557        if (err)
 558                return err;
 559
 560        err = stmfts_command(sdata, STMFTS_SLEEP_OUT);
 561        if (err)
 562                return err;
 563
 564        /* optional tuning */
 565        err = stmfts_command(sdata, STMFTS_MS_CX_TUNING);
 566        if (err)
 567                dev_warn(&sdata->client->dev,
 568                         "failed to perform mutual auto tune: %d\n", err);
 569
 570        /* optional tuning */
 571        err = stmfts_command(sdata, STMFTS_SS_CX_TUNING);
 572        if (err)
 573                dev_warn(&sdata->client->dev,
 574                         "failed to perform self auto tune: %d\n", err);
 575
 576        err = stmfts_command(sdata, STMFTS_FULL_FORCE_CALIBRATION);
 577        if (err)
 578                return err;
 579
 580        /*
 581         * At this point no one is using the touchscreen
 582         * and I don't really care about the return value
 583         */
 584        (void) i2c_smbus_write_byte(sdata->client, STMFTS_SLEEP_IN);
 585
 586        return 0;
 587}
 588
 589static void stmfts_power_off(void *data)
 590{
 591        struct stmfts_data *sdata = data;
 592
 593        disable_irq(sdata->client->irq);
 594        regulator_bulk_disable(ARRAY_SIZE(sdata->regulators),
 595                                                sdata->regulators);
 596}
 597
 598/* This function is void because I don't want to prevent using the touch key
 599 * only because the LEDs don't get registered
 600 */
 601static int stmfts_enable_led(struct stmfts_data *sdata)
 602{
 603        int err;
 604
 605        /* get the regulator for powering the leds on */
 606        sdata->ledvdd = devm_regulator_get(&sdata->client->dev, "ledvdd");
 607        if (IS_ERR(sdata->ledvdd))
 608                return PTR_ERR(sdata->ledvdd);
 609
 610        sdata->led_cdev.name = STMFTS_DEV_NAME;
 611        sdata->led_cdev.max_brightness = LED_ON;
 612        sdata->led_cdev.brightness = LED_OFF;
 613        sdata->led_cdev.brightness_set_blocking = stmfts_brightness_set;
 614        sdata->led_cdev.brightness_get = stmfts_brightness_get;
 615
 616        err = devm_led_classdev_register(&sdata->client->dev, &sdata->led_cdev);
 617        if (err) {
 618                devm_regulator_put(sdata->ledvdd);
 619                return err;
 620        }
 621
 622        return 0;
 623}
 624
 625static int stmfts_probe(struct i2c_client *client,
 626                        const struct i2c_device_id *id)
 627{
 628        int err;
 629        struct stmfts_data *sdata;
 630
 631        if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C |
 632                                                I2C_FUNC_SMBUS_BYTE_DATA |
 633                                                I2C_FUNC_SMBUS_I2C_BLOCK))
 634                return -ENODEV;
 635
 636        sdata = devm_kzalloc(&client->dev, sizeof(*sdata), GFP_KERNEL);
 637        if (!sdata)
 638                return -ENOMEM;
 639
 640        i2c_set_clientdata(client, sdata);
 641
 642        sdata->client = client;
 643        mutex_init(&sdata->mutex);
 644        init_completion(&sdata->cmd_done);
 645
 646        sdata->regulators[STMFTS_REGULATOR_VDD].supply = "vdd";
 647        sdata->regulators[STMFTS_REGULATOR_AVDD].supply = "avdd";
 648        err = devm_regulator_bulk_get(&client->dev,
 649                                      ARRAY_SIZE(sdata->regulators),
 650                                      sdata->regulators);
 651        if (err)
 652                return err;
 653
 654        sdata->input = devm_input_allocate_device(&client->dev);
 655        if (!sdata->input)
 656                return -ENOMEM;
 657
 658        sdata->input->name = STMFTS_DEV_NAME;
 659        sdata->input->id.bustype = BUS_I2C;
 660        sdata->input->open = stmfts_input_open;
 661        sdata->input->close = stmfts_input_close;
 662
 663        input_set_capability(sdata->input, EV_ABS, ABS_MT_POSITION_X);
 664        input_set_capability(sdata->input, EV_ABS, ABS_MT_POSITION_Y);
 665        touchscreen_parse_properties(sdata->input, true, &sdata->prop);
 666
 667        input_set_abs_params(sdata->input, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
 668        input_set_abs_params(sdata->input, ABS_MT_TOUCH_MINOR, 0, 255, 0, 0);
 669        input_set_abs_params(sdata->input, ABS_MT_ORIENTATION, 0, 255, 0, 0);
 670        input_set_abs_params(sdata->input, ABS_MT_PRESSURE, 0, 255, 0, 0);
 671        input_set_abs_params(sdata->input, ABS_DISTANCE, 0, 255, 0, 0);
 672
 673        sdata->use_key = device_property_read_bool(&client->dev,
 674                                                   "touch-key-connected");
 675        if (sdata->use_key) {
 676                input_set_capability(sdata->input, EV_KEY, KEY_MENU);
 677                input_set_capability(sdata->input, EV_KEY, KEY_BACK);
 678        }
 679
 680        err = input_mt_init_slots(sdata->input,
 681                                  STMFTS_MAX_FINGERS, INPUT_MT_DIRECT);
 682        if (err)
 683                return err;
 684
 685        input_set_drvdata(sdata->input, sdata);
 686
 687        /*
 688         * stmfts_power_on expects interrupt to be disabled, but
 689         * at this point the device is still off and I do not trust
 690         * the status of the irq line that can generate some spurious
 691         * interrupts. To be on the safe side it's better to not enable
 692         * the interrupts during their request.
 693         */
 694        err = devm_request_threaded_irq(&client->dev, client->irq,
 695                                        NULL, stmfts_irq_handler,
 696                                        IRQF_ONESHOT | IRQF_NO_AUTOEN,
 697                                        "stmfts_irq", sdata);
 698        if (err)
 699                return err;
 700
 701        dev_dbg(&client->dev, "initializing ST-Microelectronics FTS...\n");
 702
 703        err = stmfts_power_on(sdata);
 704        if (err)
 705                return err;
 706
 707        err = devm_add_action_or_reset(&client->dev, stmfts_power_off, sdata);
 708        if (err)
 709                return err;
 710
 711        err = input_register_device(sdata->input);
 712        if (err)
 713                return err;
 714
 715        if (sdata->use_key) {
 716                err = stmfts_enable_led(sdata);
 717                if (err) {
 718                        /*
 719                         * Even if the LEDs have failed to be initialized and
 720                         * used in the driver, I can still use the device even
 721                         * without LEDs. The ledvdd regulator pointer will be
 722                         * used as a flag.
 723                         */
 724                        dev_warn(&client->dev, "unable to use touchkey leds\n");
 725                        sdata->ledvdd = NULL;
 726                }
 727        }
 728
 729        err = devm_device_add_group(&client->dev, &stmfts_attribute_group);
 730        if (err)
 731                return err;
 732
 733        pm_runtime_enable(&client->dev);
 734        device_enable_async_suspend(&client->dev);
 735
 736        return 0;
 737}
 738
 739static int stmfts_remove(struct i2c_client *client)
 740{
 741        pm_runtime_disable(&client->dev);
 742
 743        return 0;
 744}
 745
 746static int __maybe_unused stmfts_runtime_suspend(struct device *dev)
 747{
 748        struct stmfts_data *sdata = dev_get_drvdata(dev);
 749        int ret;
 750
 751        ret = i2c_smbus_write_byte(sdata->client, STMFTS_SLEEP_IN);
 752        if (ret)
 753                dev_warn(dev, "failed to suspend device: %d\n", ret);
 754
 755        return ret;
 756}
 757
 758static int __maybe_unused stmfts_runtime_resume(struct device *dev)
 759{
 760        struct stmfts_data *sdata = dev_get_drvdata(dev);
 761        int ret;
 762
 763        ret = i2c_smbus_write_byte(sdata->client, STMFTS_SLEEP_OUT);
 764        if (ret)
 765                dev_err(dev, "failed to resume device: %d\n", ret);
 766
 767        return ret;
 768}
 769
 770static int __maybe_unused stmfts_suspend(struct device *dev)
 771{
 772        struct stmfts_data *sdata = dev_get_drvdata(dev);
 773
 774        stmfts_power_off(sdata);
 775
 776        return 0;
 777}
 778
 779static int __maybe_unused stmfts_resume(struct device *dev)
 780{
 781        struct stmfts_data *sdata = dev_get_drvdata(dev);
 782
 783        return stmfts_power_on(sdata);
 784}
 785
 786static const struct dev_pm_ops stmfts_pm_ops = {
 787        SET_SYSTEM_SLEEP_PM_OPS(stmfts_suspend, stmfts_resume)
 788        SET_RUNTIME_PM_OPS(stmfts_runtime_suspend, stmfts_runtime_resume, NULL)
 789};
 790
 791#ifdef CONFIG_OF
 792static const struct of_device_id stmfts_of_match[] = {
 793        { .compatible = "st,stmfts", },
 794        { },
 795};
 796MODULE_DEVICE_TABLE(of, stmfts_of_match);
 797#endif
 798
 799static const struct i2c_device_id stmfts_id[] = {
 800        { "stmfts", 0 },
 801        { },
 802};
 803MODULE_DEVICE_TABLE(i2c, stmfts_id);
 804
 805static struct i2c_driver stmfts_driver = {
 806        .driver = {
 807                .name = STMFTS_DEV_NAME,
 808                .of_match_table = of_match_ptr(stmfts_of_match),
 809                .pm = &stmfts_pm_ops,
 810                .probe_type = PROBE_PREFER_ASYNCHRONOUS,
 811        },
 812        .probe = stmfts_probe,
 813        .remove = stmfts_remove,
 814        .id_table = stmfts_id,
 815};
 816
 817module_i2c_driver(stmfts_driver);
 818
 819MODULE_AUTHOR("Andi Shyti <andi.shyti@samsung.com>");
 820MODULE_DESCRIPTION("STMicroelectronics FTS Touch Screen");
 821MODULE_LICENSE("GPL v2");
 822