// SPDX-License-Identifier: GPL-2.0-or-later
/*
        Copyright (C) 2004 - 2009 Ivo van Doorn <IvDoorn@gmail.com>
        <http://rt2x00.serialmonkey.com>

 */

/*
        Module: rt2500usb
        Abstract: rt2500usb device specific routines.
        Supported chipsets: RT2570.
 */

#include <linux/delay.h>
#include <linux/etherdevice.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/usb.h>

#include "rt2x00.h"
#include "rt2x00usb.h"
#include "rt2500usb.h"

/*
 * Allow hardware encryption to be disabled.
 */
static bool modparam_nohwcrypt;
module_param_named(nohwcrypt, modparam_nohwcrypt, bool, 0444);
MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption.");

/*
 * Register access.
 * All access to the CSR registers will go through the methods
 * rt2500usb_register_read and rt2500usb_register_write.
 * BBP and RF register require indirect register access,
 * and use the CSR registers BBPCSR and RFCSR to achieve this.
 * These indirect registers work with busy bits,
 * and we will try maximal REGISTER_USB_BUSY_COUNT times to access
 * the register while taking a REGISTER_BUSY_DELAY us delay
 * between each attampt. When the busy bit is still set at that time,
 * the access attempt is considered to have failed,
 * and we will print an error.
 * If the csr_mutex is already held then the _lock variants must
 * be used instead.
 */
static u16 rt2500usb_register_read(struct rt2x00_dev *rt2x00dev,
                                   const unsigned int offset)
{
        __le16 reg;
        rt2x00usb_vendor_request_buff(rt2x00dev, USB_MULTI_READ,
                                      USB_VENDOR_REQUEST_IN, offset,
                                      &reg, sizeof(reg));
        return le16_to_cpu(reg);
}

static u16 rt2500usb_register_read_lock(struct rt2x00_dev *rt2x00dev,
                                        const unsigned int offset)
{
        __le16 reg;
        rt2x00usb_vendor_req_buff_lock(rt2x00dev, USB_MULTI_READ,
                                       USB_VENDOR_REQUEST_IN, offset,
                                       &reg, sizeof(reg), REGISTER_TIMEOUT);
        return le16_to_cpu(reg);
}

static void rt2500usb_register_write(struct rt2x00_dev *rt2x00dev,
                                            const unsigned int offset,
                                            u16 value)
{
        __le16 reg = cpu_to_le16(value);
        rt2x00usb_vendor_request_buff(rt2x00dev, USB_MULTI_WRITE,
                                      USB_VENDOR_REQUEST_OUT, offset,
                                      &reg, sizeof(reg));
}

static void rt2500usb_register_write_lock(struct rt2x00_dev *rt2x00dev,
                                                 const unsigned int offset,
                                                 u16 value)
{
        __le16 reg = cpu_to_le16(value);
        rt2x00usb_vendor_req_buff_lock(rt2x00dev, USB_MULTI_WRITE,
                                       USB_VENDOR_REQUEST_OUT, offset,
                                       &reg, sizeof(reg), REGISTER_TIMEOUT);
}

static void rt2500usb_register_multiwrite(struct rt2x00_dev *rt2x00dev,
                                                 const unsigned int offset,
                                                 void *value, const u16 length)
{
        rt2x00usb_vendor_request_buff(rt2x00dev, USB_MULTI_WRITE,
                                      USB_VENDOR_REQUEST_OUT, offset,
                                      value, length);
}

static int rt2500usb_regbusy_read(struct rt2x00_dev *rt2x00dev,
                                  const unsigned int offset,
                                  struct rt2x00_field16 field,
                                  u16 *reg)
{
        unsigned int i;

        for (i = 0; i < REGISTER_USB_BUSY_COUNT; i++) {
                *reg = rt2500usb_register_read_lock(rt2x00dev, offset);
                if (!rt2x00_get_field16(*reg, field))
                        return 1;
                udelay(REGISTER_BUSY_DELAY);
        }

        rt2x00_err(rt2x00dev, "Indirect register access failed: offset=0x%.08x, value=0x%.08x\n",
                   offset, *reg);
        *reg = ~0;

        return 0;
}

#define WAIT_FOR_BBP(__dev, __reg) \
        rt2500usb_regbusy_read((__dev), PHY_CSR8, PHY_CSR8_BUSY, (__reg))
#define WAIT_FOR_RF(__dev, __reg) \
        rt2500usb_regbusy_read((__dev), PHY_CSR10, PHY_CSR10_RF_BUSY, (__reg))

static void rt2500usb_bbp_write(struct rt2x00_dev *rt2x00dev,
                                const unsigned int word, const u8 value)
{
        u16 reg;

        mutex_lock(&rt2x00dev->csr_mutex);

        /*
         * Wait until the BBP becomes available, afterwards we
         * can safely write the new data into the register.
         */
        if (WAIT_FOR_BBP(rt2x00dev, &reg)) {
                reg = 0;
                rt2x00_set_field16(&reg, PHY_CSR7_DATA, value);
                rt2x00_set_field16(&reg, PHY_CSR7_REG_ID, word);
                rt2x00_set_field16(&reg, PHY_CSR7_READ_CONTROL, 0);

                rt2500usb_register_write_lock(rt2x00dev, PHY_CSR7, reg);
        }

        mutex_unlock(&rt2x00dev->csr_mutex);
}

static u8 rt2500usb_bbp_read(struct rt2x00_dev *rt2x00dev,
                             const unsigned int word)
{
        u16 reg;
        u8 value;

        mutex_lock(&rt2x00dev->csr_mutex);

        /*
         * Wait until the BBP becomes available, afterwards we
         * can safely write the read request into the register.
         * After the data has been written, we wait until hardware
         * returns the correct value, if at any time the register
         * doesn't become available in time, reg will be 0xffffffff
         * which means we return 0xff to the caller.
         */
        if (WAIT_FOR_BBP(rt2x00dev, &reg)) {
                reg = 0;
                rt2x00_set_field16(&reg, PHY_CSR7_REG_ID, word);
                rt2x00_set_field16(&reg, PHY_CSR7_READ_CONTROL, 1);

                rt2500usb_register_write_lock(rt2x00dev, PHY_CSR7, reg);

                if (WAIT_FOR_BBP(rt2x00dev, &reg))
                        reg = rt2500usb_register_read_lock(rt2x00dev, PHY_CSR7);
        }

        value = rt2x00_get_field16(reg, PHY_CSR7_DATA);

        mutex_unlock(&rt2x00dev->csr_mutex);

        return value;
}

static void rt2500usb_rf_write(struct rt2x00_dev *rt2x00dev,
                               const unsigned int word, const u32 value)
{
        u16 reg;

        mutex_lock(&rt2x00dev->csr_mutex);

        /*
         * Wait until the RF becomes available, afterwards we
         * can safely write the new data into the register.
         */
        if (WAIT_FOR_RF(rt2x00dev, &reg)) {
                reg = 0;
                rt2x00_set_field16(&reg, PHY_CSR9_RF_VALUE, value);
                rt2500usb_register_write_lock(rt2x00dev, PHY_CSR9, reg);

                reg = 0;
                rt2x00_set_field16(&reg, PHY_CSR10_RF_VALUE, value >> 16);
                rt2x00_set_field16(&reg, PHY_CSR10_RF_NUMBER_OF_BITS, 20);
                rt2x00_set_field16(&reg, PHY_CSR10_RF_IF_SELECT, 0);
                rt2x00_set_field16(&reg, PHY_CSR10_RF_BUSY, 1);

                rt2500usb_register_write_lock(rt2x00dev, PHY_CSR10, reg);
                rt2x00_rf_write(rt2x00dev, word, value);
        }

        mutex_unlock(&rt2x00dev->csr_mutex);
}

#ifdef CONFIG_RT2X00_LIB_DEBUGFS
static u32 _rt2500usb_register_read(struct rt2x00_dev *rt2x00dev,
                                     const unsigned int offset)
{
        return rt2500usb_register_read(rt2x00dev, offset);
}

static void _rt2500usb_register_write(struct rt2x00_dev *rt2x00dev,
                                      const unsigned int offset,
                                      u32 value)
{
        rt2500usb_register_write(rt2x00dev, offset, value);
}

static const struct rt2x00debug rt2500usb_rt2x00debug = {
        .owner  = THIS_MODULE,
        .csr    = {
                .read           = _rt2500usb_register_read,
                .write          = _rt2500usb_register_write,
                .flags          = RT2X00DEBUGFS_OFFSET,
                .word_base      = CSR_REG_BASE,
                .word_size      = sizeof(u16),
                .word_count     = CSR_REG_SIZE / sizeof(u16),
        },
        .eeprom = {
                .read           = rt2x00_eeprom_read,
                .write          = rt2x00_eeprom_write,
                .word_base      = EEPROM_BASE,
                .word_size      = sizeof(u16),
                .word_count     = EEPROM_SIZE / sizeof(u16),
        },
        .bbp    = {
                .read           = rt2500usb_bbp_read,
                .write          = rt2500usb_bbp_write,
                .word_base      = BBP_BASE,
                .word_size      = sizeof(u8),
                .word_count     = BBP_SIZE / sizeof(u8),
        },
        .rf     = {
                .read           = rt2x00_rf_read,
                .write          = rt2500usb_rf_write,
                .word_base      = RF_BASE,
                .word_size      = sizeof(u32),
                .word_count     = RF_SIZE / sizeof(u32),
        },
};
#endif /* CONFIG_RT2X00_LIB_DEBUGFS */

static int rt2500usb_rfkill_poll(struct rt2x00_dev *rt2x00dev)
{
        u16 reg;

        reg = rt2500usb_register_read(rt2x00dev, MAC_CSR19);
        return rt2x00_get_field16(reg, MAC_CSR19_VAL7);
}

#ifdef CONFIG_RT2X00_LIB_LEDS
static void rt2500usb_brightness_set(struct led_classdev *led_cdev,
                                     enum led_brightness brightness)
{
        struct rt2x00_led *led =
            container_of(led_cdev, struct rt2x00_led, led_dev);
        unsigned int enabled = brightness != LED_OFF;
        u16 reg;

        reg = rt2500usb_register_read(led->rt2x00dev, MAC_CSR20);

        if (led->type == LED_TYPE_RADIO || led->type == LED_TYPE_ASSOC)
                rt2x00_set_field16(&reg, MAC_CSR20_LINK, enabled);
        else if (led->type == LED_TYPE_ACTIVITY)
                rt2x00_set_field16(&reg, MAC_CSR20_ACTIVITY, enabled);

        rt2500usb_register_write(led->rt2x00dev, MAC_CSR20, reg);
}

static int rt2500usb_blink_set(struct led_classdev *led_cdev,
                               unsigned long *delay_on,
                               unsigned long *delay_off)
{
        struct rt2x00_led *led =
            container_of(led_cdev, struct rt2x00_led, led_dev);
        u16 reg;

        reg = rt2500usb_register_read(led->rt2x00dev, MAC_CSR21);
        rt2x00_set_field16(&reg, MAC_CSR21_ON_PERIOD, *delay_on);
        rt2x00_set_field16(&reg, MAC_CSR21_OFF_PERIOD, *delay_off);
        rt2500usb_register_write(led->rt2x00dev, MAC_CSR21, reg);

        return 0;
}

static void rt2500usb_init_led(struct rt2x00_dev *rt2x00dev,
                               struct rt2x00_led *led,
                               enum led_type type)
{
        led->rt2x00dev = rt2x00dev;
        led->type = type;
        led->led_dev.brightness_set = rt2500usb_brightness_set;
        led->led_dev.blink_set = rt2500usb_blink_set;
        led->flags = LED_INITIALIZED;
}
#endif /* CONFIG_RT2X00_LIB_LEDS */

/*
 * Configuration handlers.
 */

/*
 * rt2500usb does not differentiate between shared and pairwise
 * keys, so we should use the same function for both key types.
 */
static int rt2500usb_config_key(struct rt2x00_dev *rt2x00dev,
                                struct rt2x00lib_crypto *crypto,
                                struct ieee80211_key_conf *key)
{
        u32 mask;
        u16 reg;
        enum cipher curr_cipher;

        if (crypto->cmd == SET_KEY) {
                /*
                 * Disallow to set WEP key other than with index 0,
                 * it is known that not work at least on some hardware.
                 * SW crypto will be used in that case.
                 */
                if ((key->cipher == WLAN_CIPHER_SUITE_WEP40 ||
                     key->cipher == WLAN_CIPHER_SUITE_WEP104) &&
                    key->keyidx != 0)
                        return -EOPNOTSUPP;

                /*
                 * Pairwise key will always be entry 0, but this
                 * could collide with a shared key on the same
                 * position...
                 */
                mask = TXRX_CSR0_KEY_ID.bit_mask;

                reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR0);
                curr_cipher = rt2x00_get_field16(reg, TXRX_CSR0_ALGORITHM);
                reg &= mask;

                if (reg && reg == mask)
                        return -ENOSPC;

                reg = rt2x00_get_field16(reg, TXRX_CSR0_KEY_ID);

                key->hw_key_idx += reg ? ffz(reg) : 0;
                /*
                 * Hardware requires that all keys use the same cipher
                 * (e.g. TKIP-only, AES-only, but not TKIP+AES).
                 * If this is not the first key, compare the cipher with the
                 * first one and fall back to SW crypto if not the same.
                 */
                if (key->hw_key_idx > 0 && crypto->cipher != curr_cipher)
                        return -EOPNOTSUPP;

                rt2500usb_register_multiwrite(rt2x00dev, KEY_ENTRY(key->hw_key_idx),
                                              crypto->key, sizeof(crypto->key));

                /*
                 * The driver does not support the IV/EIV generation
                 * in hardware. However it demands the data to be provided
                 * both separately as well as inside the frame.
                 * We already provided the CONFIG_CRYPTO_COPY_IV to rt2x00lib
                 * to ensure rt2x00lib will not strip the data from the
                 * frame after the copy, now we must tell mac80211
                 * to generate the IV/EIV data.
                 */
                key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
                key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC;
        }

        /*
         * TXRX_CSR0_KEY_ID contains only single-bit fields to indicate
         * a particular key is valid.
         */
        reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR0);
        rt2x00_set_field16(&reg, TXRX_CSR0_ALGORITHM, crypto->cipher);
        rt2x00_set_field16(&reg, TXRX_CSR0_IV_OFFSET, IEEE80211_HEADER);

        mask = rt2x00_get_field16(reg, TXRX_CSR0_KEY_ID);
        if (crypto->cmd == SET_KEY)
                mask |= 1 << key->hw_key_idx;
        else if (crypto->cmd == DISABLE_KEY)
                mask &= ~(1 << key->hw_key_idx);
        rt2x00_set_field16(&reg, TXRX_CSR0_KEY_ID, mask);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR0, reg);

        return 0;
}

static void rt2500usb_config_filter(struct rt2x00_dev *rt2x00dev,
                                    const unsigned int filter_flags)
{
        u16 reg;

        /*
         * Start configuration steps.
         * Note that the version error will always be dropped
         * and broadcast frames will always be accepted since
         * there is no filter for it at this time.
         */
        reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2);
        rt2x00_set_field16(&reg, TXRX_CSR2_DROP_CRC,
                           !(filter_flags & FIF_FCSFAIL));
        rt2x00_set_field16(&reg, TXRX_CSR2_DROP_PHYSICAL,
                           !(filter_flags & FIF_PLCPFAIL));
        rt2x00_set_field16(&reg, TXRX_CSR2_DROP_CONTROL,
                           !(filter_flags & FIF_CONTROL));
        rt2x00_set_field16(&reg, TXRX_CSR2_DROP_NOT_TO_ME,
                           !test_bit(CONFIG_MONITORING, &rt2x00dev->flags));
        rt2x00_set_field16(&reg, TXRX_CSR2_DROP_TODS,
                           !test_bit(CONFIG_MONITORING, &rt2x00dev->flags) &&
                           !rt2x00dev->intf_ap_count);
        rt2x00_set_field16(&reg, TXRX_CSR2_DROP_VERSION_ERROR, 1);
        rt2x00_set_field16(&reg, TXRX_CSR2_DROP_MULTICAST,
                           !(filter_flags & FIF_ALLMULTI));
        rt2x00_set_field16(&reg, TXRX_CSR2_DROP_BROADCAST, 0);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg);
}

static void rt2500usb_config_intf(struct rt2x00_dev *rt2x00dev,
                                  struct rt2x00_intf *intf,
                                  struct rt2x00intf_conf *conf,
                                  const unsigned int flags)
{
        unsigned int bcn_preload;
        u16 reg;

        if (flags & CONFIG_UPDATE_TYPE) {
                /*
                 * Enable beacon config
                 */
                bcn_preload = PREAMBLE + GET_DURATION(IEEE80211_HEADER, 20);
                reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR20);
                rt2x00_set_field16(&reg, TXRX_CSR20_OFFSET, bcn_preload >> 6);
                rt2x00_set_field16(&reg, TXRX_CSR20_BCN_EXPECT_WINDOW,
                                   2 * (conf->type != NL80211_IFTYPE_STATION));
                rt2500usb_register_write(rt2x00dev, TXRX_CSR20, reg);

                /*
                 * Enable synchronisation.
                 */
                reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR18);
                rt2x00_set_field16(&reg, TXRX_CSR18_OFFSET, 0);
                rt2500usb_register_write(rt2x00dev, TXRX_CSR18, reg);

                reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19);
                rt2x00_set_field16(&reg, TXRX_CSR19_TSF_SYNC, conf->sync);
                rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg);
        }

        if (flags & CONFIG_UPDATE_MAC)
                rt2500usb_register_multiwrite(rt2x00dev, MAC_CSR2, conf->mac,
                                              (3 * sizeof(__le16)));

        if (flags & CONFIG_UPDATE_BSSID)
                rt2500usb_register_multiwrite(rt2x00dev, MAC_CSR5, conf->bssid,
                                              (3 * sizeof(__le16)));
}

static void rt2500usb_config_erp(struct rt2x00_dev *rt2x00dev,
                                 struct rt2x00lib_erp *erp,
                                 u32 changed)
{
        u16 reg;

        if (changed & BSS_CHANGED_ERP_PREAMBLE) {
                reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR10);
                rt2x00_set_field16(&reg, TXRX_CSR10_AUTORESPOND_PREAMBLE,
                                   !!erp->short_preamble);
                rt2500usb_register_write(rt2x00dev, TXRX_CSR10, reg);
        }

        if (changed & BSS_CHANGED_BASIC_RATES)
                rt2500usb_register_write(rt2x00dev, TXRX_CSR11,
                                         erp->basic_rates);

        if (changed & BSS_CHANGED_BEACON_INT) {
                reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR18);
                rt2x00_set_field16(&reg, TXRX_CSR18_INTERVAL,
                                   erp->beacon_int * 4);
                rt2500usb_register_write(rt2x00dev, TXRX_CSR18, reg);
        }

        if (changed & BSS_CHANGED_ERP_SLOT) {
                rt2500usb_register_write(rt2x00dev, MAC_CSR10, erp->slot_time);
                rt2500usb_register_write(rt2x00dev, MAC_CSR11, erp->sifs);
                rt2500usb_register_write(rt2x00dev, MAC_CSR12, erp->eifs);
        }
}

static void rt2500usb_config_ant(struct rt2x00_dev *rt2x00dev,
                                 struct antenna_setup *ant)
{
        u8 r2;
        u8 r14;
        u16 csr5;
        u16 csr6;

        /*
         * We should never come here because rt2x00lib is supposed
         * to catch this and send us the correct antenna explicitely.
         */
        BUG_ON(ant->rx == ANTENNA_SW_DIVERSITY ||
               ant->tx == ANTENNA_SW_DIVERSITY);

        r2 = rt2500usb_bbp_read(rt2x00dev, 2);
        r14 = rt2500usb_bbp_read(rt2x00dev, 14);
        csr5 = rt2500usb_register_read(rt2x00dev, PHY_CSR5);
        csr6 = rt2500usb_register_read(rt2x00dev, PHY_CSR6);

        /*
         * Configure the TX antenna.
         */
        switch (ant->tx) {
        case ANTENNA_HW_DIVERSITY:
                rt2x00_set_field8(&r2, BBP_R2_TX_ANTENNA, 1);
                rt2x00_set_field16(&csr5, PHY_CSR5_CCK, 1);
                rt2x00_set_field16(&csr6, PHY_CSR6_OFDM, 1);
                break;
        case ANTENNA_A:
                rt2x00_set_field8(&r2, BBP_R2_TX_ANTENNA, 0);
                rt2x00_set_field16(&csr5, PHY_CSR5_CCK, 0);
                rt2x00_set_field16(&csr6, PHY_CSR6_OFDM, 0);
                break;
        case ANTENNA_B:
        default:
                rt2x00_set_field8(&r2, BBP_R2_TX_ANTENNA, 2);
                rt2x00_set_field16(&csr5, PHY_CSR5_CCK, 2);
                rt2x00_set_field16(&csr6, PHY_CSR6_OFDM, 2);
                break;
        }

        /*
         * Configure the RX antenna.
         */
        switch (ant->rx) {
        case ANTENNA_HW_DIVERSITY:
                rt2x00_set_field8(&r14, BBP_R14_RX_ANTENNA, 1);
                break;
        case ANTENNA_A:
                rt2x00_set_field8(&r14, BBP_R14_RX_ANTENNA, 0);
                break;
        case ANTENNA_B:
        default:
                rt2x00_set_field8(&r14, BBP_R14_RX_ANTENNA, 2);
                break;
        }

        /*
         * RT2525E and RT5222 need to flip TX I/Q
         */
        if (rt2x00_rf(rt2x00dev, RF2525E) || rt2x00_rf(rt2x00dev, RF5222)) {
                rt2x00_set_field8(&r2, BBP_R2_TX_IQ_FLIP, 1);
                rt2x00_set_field16(&csr5, PHY_CSR5_CCK_FLIP, 1);
                rt2x00_set_field16(&csr6, PHY_CSR6_OFDM_FLIP, 1);

                /*
                 * RT2525E does not need RX I/Q Flip.
                 */
                if (rt2x00_rf(rt2x00dev, RF2525E))
                        rt2x00_set_field8(&r14, BBP_R14_RX_IQ_FLIP, 0);
        } else {
                rt2x00_set_field16(&csr5, PHY_CSR5_CCK_FLIP, 0);
                rt2x00_set_field16(&csr6, PHY_CSR6_OFDM_FLIP, 0);
        }

        rt2500usb_bbp_write(rt2x00dev, 2, r2);
        rt2500usb_bbp_write(rt2x00dev, 14, r14);
        rt2500usb_register_write(rt2x00dev, PHY_CSR5, csr5);
        rt2500usb_register_write(rt2x00dev, PHY_CSR6, csr6);
}

static void rt2500usb_config_channel(struct rt2x00_dev *rt2x00dev,
                                     struct rf_channel *rf, const int txpower)
{
        /*
         * Set TXpower.
         */
        rt2x00_set_field32(&rf->rf3, RF3_TXPOWER, TXPOWER_TO_DEV(txpower));

        /*
         * For RT2525E we should first set the channel to half band higher.
         */
        if (rt2x00_rf(rt2x00dev, RF2525E)) {
                static const u32 vals[] = {
                        0x000008aa, 0x000008ae, 0x000008ae, 0x000008b2,
                        0x000008b2, 0x000008b6, 0x000008b6, 0x000008ba,
                        0x000008ba, 0x000008be, 0x000008b7, 0x00000902,
                        0x00000902, 0x00000906
                };

                rt2500usb_rf_write(rt2x00dev, 2, vals[rf->channel - 1]);
                if (rf->rf4)
                        rt2500usb_rf_write(rt2x00dev, 4, rf->rf4);
        }

        rt2500usb_rf_write(rt2x00dev, 1, rf->rf1);
        rt2500usb_rf_write(rt2x00dev, 2, rf->rf2);
        rt2500usb_rf_write(rt2x00dev, 3, rf->rf3);
        if (rf->rf4)
                rt2500usb_rf_write(rt2x00dev, 4, rf->rf4);
}

static void rt2500usb_config_txpower(struct rt2x00_dev *rt2x00dev,
                                     const int txpower)
{
        u32 rf3;

        rf3 = rt2x00_rf_read(rt2x00dev, 3);
        rt2x00_set_field32(&rf3, RF3_TXPOWER, TXPOWER_TO_DEV(txpower));
        rt2500usb_rf_write(rt2x00dev, 3, rf3);
}

static void rt2500usb_config_ps(struct rt2x00_dev *rt2x00dev,
                                struct rt2x00lib_conf *libconf)
{
        enum dev_state state =
            (libconf->conf->flags & IEEE80211_CONF_PS) ?
                STATE_SLEEP : STATE_AWAKE;
        u16 reg;

        if (state == STATE_SLEEP) {
                reg = rt2500usb_register_read(rt2x00dev, MAC_CSR18);
                rt2x00_set_field16(&reg, MAC_CSR18_DELAY_AFTER_BEACON,
                                   rt2x00dev->beacon_int - 20);
                rt2x00_set_field16(&reg, MAC_CSR18_BEACONS_BEFORE_WAKEUP,
                                   libconf->conf->listen_interval - 1);

                /* We must first disable autowake before it can be enabled */
                rt2x00_set_field16(&reg, MAC_CSR18_AUTO_WAKE, 0);
                rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg);

                rt2x00_set_field16(&reg, MAC_CSR18_AUTO_WAKE, 1);
                rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg);
        } else {
                reg = rt2500usb_register_read(rt2x00dev, MAC_CSR18);
                rt2x00_set_field16(&reg, MAC_CSR18_AUTO_WAKE, 0);
                rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg);
        }

        rt2x00dev->ops->lib->set_device_state(rt2x00dev, state);
}

static void rt2500usb_config(struct rt2x00_dev *rt2x00dev,
                             struct rt2x00lib_conf *libconf,
                             const unsigned int flags)
{
        if (flags & IEEE80211_CONF_CHANGE_CHANNEL)
                rt2500usb_config_channel(rt2x00dev, &libconf->rf,
                                         libconf->conf->power_level);
        if ((flags & IEEE80211_CONF_CHANGE_POWER) &&
            !(flags & IEEE80211_CONF_CHANGE_CHANNEL))
                rt2500usb_config_txpower(rt2x00dev,
                                         libconf->conf->power_level);
        if (flags & IEEE80211_CONF_CHANGE_PS)
                rt2500usb_config_ps(rt2x00dev, libconf);
}

/*
 * Link tuning
 */
static void rt2500usb_link_stats(struct rt2x00_dev *rt2x00dev,
                                 struct link_qual *qual)
{
        u16 reg;

        /*
         * Update FCS error count from register.
         */
        reg = rt2500usb_register_read(rt2x00dev, STA_CSR0);
        qual->rx_failed = rt2x00_get_field16(reg, STA_CSR0_FCS_ERROR);

        /*
         * Update False CCA count from register.
         */
        reg = rt2500usb_register_read(rt2x00dev, STA_CSR3);
        qual->false_cca = rt2x00_get_field16(reg, STA_CSR3_FALSE_CCA_ERROR);
}

static void rt2500usb_reset_tuner(struct rt2x00_dev *rt2x00dev,
                                  struct link_qual *qual)
{
        u16 eeprom;
        u16 value;

        eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R24);
        value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_R24_LOW);
        rt2500usb_bbp_write(rt2x00dev, 24, value);

        eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R25);
        value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_R25_LOW);
        rt2500usb_bbp_write(rt2x00dev, 25, value);

        eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R61);
        value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_R61_LOW);
        rt2500usb_bbp_write(rt2x00dev, 61, value);

        eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_VGC);
        value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_VGCUPPER);
        rt2500usb_bbp_write(rt2x00dev, 17, value);

        qual->vgc_level = value;
}

/*
 * Queue handlers.
 */
static void rt2500usb_start_queue(struct data_queue *queue)
{
        struct rt2x00_dev *rt2x00dev = queue->rt2x00dev;
        u16 reg;

        switch (queue->qid) {
        case QID_RX:
                reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2);
                rt2x00_set_field16(&reg, TXRX_CSR2_DISABLE_RX, 0);
                rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg);
                break;
        case QID_BEACON:
                reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19);
                rt2x00_set_field16(&reg, TXRX_CSR19_TSF_COUNT, 1);
                rt2x00_set_field16(&reg, TXRX_CSR19_TBCN, 1);
                rt2x00_set_field16(&reg, TXRX_CSR19_BEACON_GEN, 1);
                rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg);
                break;
        default:
                break;
        }
}

static void rt2500usb_stop_queue(struct data_queue *queue)
{
        struct rt2x00_dev *rt2x00dev = queue->rt2x00dev;
        u16 reg;

        switch (queue->qid) {
        case QID_RX:
                reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2);
                rt2x00_set_field16(&reg, TXRX_CSR2_DISABLE_RX, 1);
                rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg);
                break;
        case QID_BEACON:
                reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19);
                rt2x00_set_field16(&reg, TXRX_CSR19_TSF_COUNT, 0);
                rt2x00_set_field16(&reg, TXRX_CSR19_TBCN, 0);
                rt2x00_set_field16(&reg, TXRX_CSR19_BEACON_GEN, 0);
                rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg);
                break;
        default:
                break;
        }
}

/*
 * Initialization functions.
 */
static int rt2500usb_init_registers(struct rt2x00_dev *rt2x00dev)
{
        u16 reg;

        rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE, 0x0001,
                                    USB_MODE_TEST, REGISTER_TIMEOUT);
        rt2x00usb_vendor_request_sw(rt2x00dev, USB_SINGLE_WRITE, 0x0308,
                                    0x00f0, REGISTER_TIMEOUT);

        reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2);
        rt2x00_set_field16(&reg, TXRX_CSR2_DISABLE_RX, 1);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg);

        rt2500usb_register_write(rt2x00dev, MAC_CSR13, 0x1111);
        rt2500usb_register_write(rt2x00dev, MAC_CSR14, 0x1e11);

        reg = rt2500usb_register_read(rt2x00dev, MAC_CSR1);
        rt2x00_set_field16(&reg, MAC_CSR1_SOFT_RESET, 1);
        rt2x00_set_field16(&reg, MAC_CSR1_BBP_RESET, 1);
        rt2x00_set_field16(&reg, MAC_CSR1_HOST_READY, 0);
        rt2500usb_register_write(rt2x00dev, MAC_CSR1, reg);

        reg = rt2500usb_register_read(rt2x00dev, MAC_CSR1);
        rt2x00_set_field16(&reg, MAC_CSR1_SOFT_RESET, 0);
        rt2x00_set_field16(&reg, MAC_CSR1_BBP_RESET, 0);
        rt2x00_set_field16(&reg, MAC_CSR1_HOST_READY, 0);
        rt2500usb_register_write(rt2x00dev, MAC_CSR1, reg);

        reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR5);
        rt2x00_set_field16(&reg, TXRX_CSR5_BBP_ID0, 13);
        rt2x00_set_field16(&reg, TXRX_CSR5_BBP_ID0_VALID, 1);
        rt2x00_set_field16(&reg, TXRX_CSR5_BBP_ID1, 12);
        rt2x00_set_field16(&reg, TXRX_CSR5_BBP_ID1_VALID, 1);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR5, reg);

        reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR6);
        rt2x00_set_field16(&reg, TXRX_CSR6_BBP_ID0, 10);
        rt2x00_set_field16(&reg, TXRX_CSR6_BBP_ID0_VALID, 1);
        rt2x00_set_field16(&reg, TXRX_CSR6_BBP_ID1, 11);
        rt2x00_set_field16(&reg, TXRX_CSR6_BBP_ID1_VALID, 1);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR6, reg);

        reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR7);
        rt2x00_set_field16(&reg, TXRX_CSR7_BBP_ID0, 7);
        rt2x00_set_field16(&reg, TXRX_CSR7_BBP_ID0_VALID, 1);
        rt2x00_set_field16(&reg, TXRX_CSR7_BBP_ID1, 6);
        rt2x00_set_field16(&reg, TXRX_CSR7_BBP_ID1_VALID, 1);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR7, reg);

        reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR8);
        rt2x00_set_field16(&reg, TXRX_CSR8_BBP_ID0, 5);
        rt2x00_set_field16(&reg, TXRX_CSR8_BBP_ID0_VALID, 1);
        rt2x00_set_field16(&reg, TXRX_CSR8_BBP_ID1, 0);
        rt2x00_set_field16(&reg, TXRX_CSR8_BBP_ID1_VALID, 0);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR8, reg);

        reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19);
        rt2x00_set_field16(&reg, TXRX_CSR19_TSF_COUNT, 0);
        rt2x00_set_field16(&reg, TXRX_CSR19_TSF_SYNC, 0);
        rt2x00_set_field16(&reg, TXRX_CSR19_TBCN, 0);
        rt2x00_set_field16(&reg, TXRX_CSR19_BEACON_GEN, 0);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg);

        rt2500usb_register_write(rt2x00dev, TXRX_CSR21, 0xe78f);
        rt2500usb_register_write(rt2x00dev, MAC_CSR9, 0xff1d);

        if (rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_AWAKE))
                return -EBUSY;

        reg = rt2500usb_register_read(rt2x00dev, MAC_CSR1);
        rt2x00_set_field16(&reg, MAC_CSR1_SOFT_RESET, 0);
        rt2x00_set_field16(&reg, MAC_CSR1_BBP_RESET, 0);
        rt2x00_set_field16(&reg, MAC_CSR1_HOST_READY, 1);
        rt2500usb_register_write(rt2x00dev, MAC_CSR1, reg);

        if (rt2x00_rev(rt2x00dev) >= RT2570_VERSION_C) {
                reg = rt2500usb_register_read(rt2x00dev, PHY_CSR2);
                rt2x00_set_field16(&reg, PHY_CSR2_LNA, 0);
        } else {
                reg = 0;
                rt2x00_set_field16(&reg, PHY_CSR2_LNA, 1);
                rt2x00_set_field16(&reg, PHY_CSR2_LNA_MODE, 3);
        }
        rt2500usb_register_write(rt2x00dev, PHY_CSR2, reg);

        rt2500usb_register_write(rt2x00dev, MAC_CSR11, 0x0002);
        rt2500usb_register_write(rt2x00dev, MAC_CSR22, 0x0053);
        rt2500usb_register_write(rt2x00dev, MAC_CSR15, 0x01ee);
        rt2500usb_register_write(rt2x00dev, MAC_CSR16, 0x0000);

        reg = rt2500usb_register_read(rt2x00dev, MAC_CSR8);
        rt2x00_set_field16(&reg, MAC_CSR8_MAX_FRAME_UNIT,
                           rt2x00dev->rx->data_size);
        rt2500usb_register_write(rt2x00dev, MAC_CSR8, reg);

        reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR0);
        rt2x00_set_field16(&reg, TXRX_CSR0_ALGORITHM, CIPHER_NONE);
        rt2x00_set_field16(&reg, TXRX_CSR0_IV_OFFSET, IEEE80211_HEADER);
        rt2x00_set_field16(&reg, TXRX_CSR0_KEY_ID, 0);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR0, reg);

        reg = rt2500usb_register_read(rt2x00dev, MAC_CSR18);
        rt2x00_set_field16(&reg, MAC_CSR18_DELAY_AFTER_BEACON, 90);
        rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg);

        reg = rt2500usb_register_read(rt2x00dev, PHY_CSR4);
        rt2x00_set_field16(&reg, PHY_CSR4_LOW_RF_LE, 1);
        rt2500usb_register_write(rt2x00dev, PHY_CSR4, reg);

        reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR1);
        rt2x00_set_field16(&reg, TXRX_CSR1_AUTO_SEQUENCE, 1);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR1, reg);

        return 0;
}

static int rt2500usb_wait_bbp_ready(struct rt2x00_dev *rt2x00dev)
{
        unsigned int i;
        u8 value;

        for (i = 0; i < REGISTER_USB_BUSY_COUNT; i++) {
                value = rt2500usb_bbp_read(rt2x00dev, 0);
                if ((value != 0xff) && (value != 0x00))
                        return 0;
                udelay(REGISTER_BUSY_DELAY);
        }

        rt2x00_err(rt2x00dev, "BBP register access failed, aborting\n");
        return -EACCES;
}

static int rt2500usb_init_bbp(struct rt2x00_dev *rt2x00dev)
{
        unsigned int i;
        u16 eeprom;
        u8 value;
        u8 reg_id;

        if (unlikely(rt2500usb_wait_bbp_ready(rt2x00dev)))
                return -EACCES;

        rt2500usb_bbp_write(rt2x00dev, 3, 0x02);
        rt2500usb_bbp_write(rt2x00dev, 4, 0x19);
        rt2500usb_bbp_write(rt2x00dev, 14, 0x1c);
        rt2500usb_bbp_write(rt2x00dev, 15, 0x30);
        rt2500usb_bbp_write(rt2x00dev, 16, 0xac);
        rt2500usb_bbp_write(rt2x00dev, 18, 0x18);
        rt2500usb_bbp_write(rt2x00dev, 19, 0xff);
        rt2500usb_bbp_write(rt2x00dev, 20, 0x1e);
        rt2500usb_bbp_write(rt2x00dev, 21, 0x08);
        rt2500usb_bbp_write(rt2x00dev, 22, 0x08);
        rt2500usb_bbp_write(rt2x00dev, 23, 0x08);
        rt2500usb_bbp_write(rt2x00dev, 24, 0x80);
        rt2500usb_bbp_write(rt2x00dev, 25, 0x50);
        rt2500usb_bbp_write(rt2x00dev, 26, 0x08);
        rt2500usb_bbp_write(rt2x00dev, 27, 0x23);
        rt2500usb_bbp_write(rt2x00dev, 30, 0x10);
        rt2500usb_bbp_write(rt2x00dev, 31, 0x2b);
        rt2500usb_bbp_write(rt2x00dev, 32, 0xb9);
        rt2500usb_bbp_write(rt2x00dev, 34, 0x12);
        rt2500usb_bbp_write(rt2x00dev, 35, 0x50);
        rt2500usb_bbp_write(rt2x00dev, 39, 0xc4);
        rt2500usb_bbp_write(rt2x00dev, 40, 0x02);
        rt2500usb_bbp_write(rt2x00dev, 41, 0x60);
        rt2500usb_bbp_write(rt2x00dev, 53, 0x10);
        rt2500usb_bbp_write(rt2x00dev, 54, 0x18);
        rt2500usb_bbp_write(rt2x00dev, 56, 0x08);
        rt2500usb_bbp_write(rt2x00dev, 57, 0x10);
        rt2500usb_bbp_write(rt2x00dev, 58, 0x08);
        rt2500usb_bbp_write(rt2x00dev, 61, 0x60);
        rt2500usb_bbp_write(rt2x00dev, 62, 0x10);
        rt2500usb_bbp_write(rt2x00dev, 75, 0xff);

        for (i = 0; i < EEPROM_BBP_SIZE; i++) {
                eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBP_START + i);

                if (eeprom != 0xffff && eeprom != 0x0000) {
                        reg_id = rt2x00_get_field16(eeprom, EEPROM_BBP_REG_ID);
                        value = rt2x00_get_field16(eeprom, EEPROM_BBP_VALUE);
                        rt2500usb_bbp_write(rt2x00dev, reg_id, value);
                }
        }

        return 0;
}

/*
 * Device state switch handlers.
 */
static int rt2500usb_enable_radio(struct rt2x00_dev *rt2x00dev)
{
        /*
         * Initialize all registers.
         */
        if (unlikely(rt2500usb_init_registers(rt2x00dev) ||
                     rt2500usb_init_bbp(rt2x00dev)))
                return -EIO;

        return 0;
}

static void rt2500usb_disable_radio(struct rt2x00_dev *rt2x00dev)
{
        rt2500usb_register_write(rt2x00dev, MAC_CSR13, 0x2121);
        rt2500usb_register_write(rt2x00dev, MAC_CSR14, 0x2121);

        /*
         * Disable synchronisation.
         */
        rt2500usb_register_write(rt2x00dev, TXRX_CSR19, 0);

        rt2x00usb_disable_radio(rt2x00dev);
}

static int rt2500usb_set_state(struct rt2x00_dev *rt2x00dev,
                               enum dev_state state)
{
        u16 reg;
        u16 reg2;
        unsigned int i;
        char put_to_sleep;
        char bbp_state;
        char rf_state;

        put_to_sleep = (state != STATE_AWAKE);

        reg = 0;
        rt2x00_set_field16(&reg, MAC_CSR17_BBP_DESIRE_STATE, state);
        rt2x00_set_field16(&reg, MAC_CSR17_RF_DESIRE_STATE, state);
        rt2x00_set_field16(&reg, MAC_CSR17_PUT_TO_SLEEP, put_to_sleep);
        rt2500usb_register_write(rt2x00dev, MAC_CSR17, reg);
        rt2x00_set_field16(&reg, MAC_CSR17_SET_STATE, 1);
        rt2500usb_register_write(rt2x00dev, MAC_CSR17, reg);

        /*
         * Device is not guaranteed to be in the requested state yet.
         * We must wait until the register indicates that the
         * device has entered the correct state.
         */
        for (i = 0; i < REGISTER_USB_BUSY_COUNT; i++) {
                reg2 = rt2500usb_register_read(rt2x00dev, MAC_CSR17);
                bbp_state = rt2x00_get_field16(reg2, MAC_CSR17_BBP_CURR_STATE);
                rf_state = rt2x00_get_field16(reg2, MAC_CSR17_RF_CURR_STATE);
                if (bbp_state == state && rf_state == state)
                        return 0;
                rt2500usb_register_write(rt2x00dev, MAC_CSR17, reg);
                msleep(30);
        }

        return -EBUSY;
}

static int rt2500usb_set_device_state(struct rt2x00_dev *rt2x00dev,
                                      enum dev_state state)
{
        int retval = 0;

        switch (state) {
        case STATE_RADIO_ON:
                retval = rt2500usb_enable_radio(rt2x00dev);
                break;
        case STATE_RADIO_OFF:
                rt2500usb_disable_radio(rt2x00dev);
                break;
        case STATE_RADIO_IRQ_ON:
        case STATE_RADIO_IRQ_OFF:
                /* No support, but no error either */
                break;
        case STATE_DEEP_SLEEP:
        case STATE_SLEEP:
        case STATE_STANDBY:
        case STATE_AWAKE:
                retval = rt2500usb_set_state(rt2x00dev, state);
                break;
        default:
                retval = -ENOTSUPP;
                break;
        }

        if (unlikely(retval))
                rt2x00_err(rt2x00dev, "Device failed to enter state %d (%d)\n",
                           state, retval);

        return retval;
}

/*
 * TX descriptor initialization
 */
static void rt2500usb_write_tx_desc(struct queue_entry *entry,
                                    struct txentry_desc *txdesc)
{
        struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
        __le32 *txd = (__le32 *) entry->skb->data;
        u32 word;

        /*
         * Start writing the descriptor words.
         */
        word = rt2x00_desc_read(txd, 0);
        rt2x00_set_field32(&word, TXD_W0_RETRY_LIMIT, txdesc->retry_limit);
        rt2x00_set_field32(&word, TXD_W0_MORE_FRAG,
                           test_bit(ENTRY_TXD_MORE_FRAG, &txdesc->flags));
        rt2x00_set_field32(&word, TXD_W0_ACK,
                           test_bit(ENTRY_TXD_ACK, &txdesc->flags));
        rt2x00_set_field32(&word, TXD_W0_TIMESTAMP,
                           test_bit(ENTRY_TXD_REQ_TIMESTAMP, &txdesc->flags));
        rt2x00_set_field32(&word, TXD_W0_OFDM,
                           (txdesc->rate_mode == RATE_MODE_OFDM));
        rt2x00_set_field32(&word, TXD_W0_NEW_SEQ,
                           test_bit(ENTRY_TXD_FIRST_FRAGMENT, &txdesc->flags));
        rt2x00_set_field32(&word, TXD_W0_IFS, txdesc->u.plcp.ifs);
        rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, txdesc->length);
        rt2x00_set_field32(&word, TXD_W0_CIPHER, !!txdesc->cipher);
        rt2x00_set_field32(&word, TXD_W0_KEY_ID, txdesc->key_idx);
        rt2x00_desc_write(txd, 0, word);

        word = rt2x00_desc_read(txd, 1);
        rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, txdesc->iv_offset);
        rt2x00_set_field32(&word, TXD_W1_AIFS, entry->queue->aifs);
        rt2x00_set_field32(&word, TXD_W1_CWMIN, entry->queue->cw_min);
        rt2x00_set_field32(&word, TXD_W1_CWMAX, entry->queue->cw_max);
        rt2x00_desc_write(txd, 1, word);

        word = rt2x00_desc_read(txd, 2);
        rt2x00_set_field32(&word, TXD_W2_PLCP_SIGNAL, txdesc->u.plcp.signal);
        rt2x00_set_field32(&word, TXD_W2_PLCP_SERVICE, txdesc->u.plcp.service);
        rt2x00_set_field32(&word, TXD_W2_PLCP_LENGTH_LOW,
                           txdesc->u.plcp.length_low);
        rt2x00_set_field32(&word, TXD_W2_PLCP_LENGTH_HIGH,
                           txdesc->u.plcp.length_high);
        rt2x00_desc_write(txd, 2, word);

        if (test_bit(ENTRY_TXD_ENCRYPT, &txdesc->flags)) {
                _rt2x00_desc_write(txd, 3, skbdesc->iv[0]);
                _rt2x00_desc_write(txd, 4, skbdesc->iv[1]);
        }

        /*
         * Register descriptor details in skb frame descriptor.
         */
        skbdesc->flags |= SKBDESC_DESC_IN_SKB;
        skbdesc->desc = txd;
        skbdesc->desc_len = TXD_DESC_SIZE;
}

/*
 * TX data initialization
 */
static void rt2500usb_beacondone(struct urb *urb);

static void rt2500usb_write_beacon(struct queue_entry *entry,
                                   struct txentry_desc *txdesc)
{
        struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
        struct usb_device *usb_dev = to_usb_device_intf(rt2x00dev->dev);
        struct queue_entry_priv_usb_bcn *bcn_priv = entry->priv_data;
        int pipe = usb_sndbulkpipe(usb_dev, entry->queue->usb_endpoint);
        int length;
        u16 reg, reg0;

        /*
         * Disable beaconing while we are reloading the beacon data,
         * otherwise we might be sending out invalid data.
         */
        reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19);
        rt2x00_set_field16(&reg, TXRX_CSR19_BEACON_GEN, 0);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg);

        /*
         * Add space for the descriptor in front of the skb.
         */
        skb_push(entry->skb, TXD_DESC_SIZE);
        memset(entry->skb->data, 0, TXD_DESC_SIZE);

        /*
         * Write the TX descriptor for the beacon.
         */
        rt2500usb_write_tx_desc(entry, txdesc);

        /*
         * Dump beacon to userspace through debugfs.
         */
        rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_BEACON, entry);

        /*
         * USB devices cannot blindly pass the skb->len as the
         * length of the data to usb_fill_bulk_urb. Pass the skb
         * to the driver to determine what the length should be.
         */
        length = rt2x00dev->ops->lib->get_tx_data_len(entry);

        usb_fill_bulk_urb(bcn_priv->urb, usb_dev, pipe,
                          entry->skb->data, length, rt2500usb_beacondone,
                          entry);

        /*
         * Second we need to create the guardian byte.
         * We only need a single byte, so lets recycle
         * the 'flags' field we are not using for beacons.
         */
        bcn_priv->guardian_data = 0;
        usb_fill_bulk_urb(bcn_priv->guardian_urb, usb_dev, pipe,
                          &bcn_priv->guardian_data, 1, rt2500usb_beacondone,
                          entry);

        /*
         * Send out the guardian byte.
         */
        usb_submit_urb(bcn_priv->guardian_urb, GFP_ATOMIC);

        /*
         * Enable beaconing again.
         */
        rt2x00_set_field16(&reg, TXRX_CSR19_TSF_COUNT, 1);
        rt2x00_set_field16(&reg, TXRX_CSR19_TBCN, 1);
        reg0 = reg;
        rt2x00_set_field16(&reg, TXRX_CSR19_BEACON_GEN, 1);
        /*
         * Beacon generation will fail initially.
         * To prevent this we need to change the TXRX_CSR19
         * register several times (reg0 is the same as reg
         * except for TXRX_CSR19_BEACON_GEN, which is 0 in reg0
         * and 1 in reg).
         */
        rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg0);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg0);
        rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg);
}

static int rt2500usb_get_tx_data_len(struct queue_entry *entry)
{
        int length;

        /*
         * The length _must_ be a multiple of 2,
         * but it must _not_ be a multiple of the USB packet size.
         */
        length = roundup(entry->skb->len, 2);
        length += (2 * !(length % entry->queue->usb_maxpacket));

        return length;
}

/*
 * RX control handlers
 */
static void rt2500usb_fill_rxdone(struct queue_entry *entry,
                                  struct rxdone_entry_desc *rxdesc)
{
        struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev;
        struct queue_entry_priv_usb *entry_priv = entry->priv_data;
        struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb);
        __le32 *rxd =
            (__le32 *)(entry->skb->data +
                       (entry_priv->urb->actual_length -
                        entry->queue->desc_size));
        u32 word0;
        u32 word1;

        /*
         * Copy descriptor to the skbdesc->desc buffer, making it safe from moving of
         * frame data in rt2x00usb.
         */
        memcpy(skbdesc->desc, rxd, skbdesc->desc_len);
        rxd = (__le32 *)skbdesc->desc;

        /*
         * It is now safe to read the descriptor on all architectures.
         */
        word0 = rt2x00_desc_read(rxd, 0);
        word1 = rt2x00_desc_read(rxd, 1);

        if (rt2x00_get_field32(word0, RXD_W0_CRC_ERROR))
                rxdesc->flags |= RX_FLAG_FAILED_FCS_CRC;
        if (rt2x00_get_field32(word0, RXD_W0_PHYSICAL_ERROR))
                rxdesc->flags |= RX_FLAG_FAILED_PLCP_CRC;

        rxdesc->cipher = rt2x00_get_field32(word0, RXD_W0_CIPHER);
        if (rt2x00_get_field32(word0, RXD_W0_CIPHER_ERROR))
                rxdesc->cipher_status = RX_CRYPTO_FAIL_KEY;

        if (rxdesc->cipher != CIPHER_NONE) {
                rxdesc->iv[0] = _rt2x00_desc_read(rxd, 2);
                rxdesc->iv[1] = _rt2x00_desc_read(rxd, 3);
                rxdesc->dev_flags |= RXDONE_CRYPTO_IV;

                /* ICV is located at the end of frame */

                rxdesc->flags |= RX_FLAG_MMIC_STRIPPED;
                if (rxdesc->cipher_status == RX_CRYPTO_SUCCESS)
                        rxdesc->flags |= RX_FLAG_DECRYPTED;
                else if (rxdesc->cipher_status == RX_CRYPTO_FAIL_MIC)
                        rxdesc->flags |= RX_FLAG_MMIC_ERROR;
        }

        /*
         * Obtain the status about this packet.
         * When frame was received with an OFDM bitrate,
         * the signal is the PLCP value. If it was received with
         * a CCK bitrate the signal is the rate in 100kbit/s.
         */
        rxdesc->signal = rt2x00_get_field32(word1, RXD_W1_SIGNAL);
        rxdesc->rssi =
            rt2x00_get_field32(word1, RXD_W1_RSSI) - rt2x00dev->rssi_offset;
        rxdesc->size = rt2x00_get_field32(word0, RXD_W0_DATABYTE_COUNT);

        if (rt2x00_get_field32(word0, RXD_W0_OFDM))
                rxdesc->dev_flags |= RXDONE_SIGNAL_PLCP;
        else
                rxdesc->dev_flags |= RXDONE_SIGNAL_BITRATE;
        if (rt2x00_get_field32(word0, RXD_W0_MY_BSS))
                rxdesc->dev_flags |= RXDONE_MY_BSS;

        /*
         * Adjust the skb memory window to the frame boundaries.
         */
        skb_trim(entry->skb, rxdesc->size);
}

/*
 * Interrupt functions.
 */
static void rt2500usb_beacondone(struct urb *urb)
{
        struct queue_entry *entry = (struct queue_entry *)urb->context;
        struct queue_entry_priv_usb_bcn *bcn_priv = entry->priv_data;

        if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &entry->queue->rt2x00dev->flags))
                return;

        /*
         * Check if this was the guardian beacon,
         * if that was the case we need to send the real beacon now.
         * Otherwise we should free the sk_buffer, the device
         * should be doing the rest of the work now.
         */
        if (bcn_priv->guardian_urb == urb) {
                usb_submit_urb(bcn_priv->urb, GFP_ATOMIC);
        } else if (bcn_priv->urb == urb) {
                dev_kfree_skb(entry->skb);
                entry->skb = NULL;
        }
}

/*
 * Device probe functions.
 */
static int rt2500usb_validate_eeprom(struct rt2x00_dev *rt2x00dev)
{
        u16 word;
        u8 *mac;
        u8 bbp;

        rt2x00usb_eeprom_read(rt2x00dev, rt2x00dev->eeprom, EEPROM_SIZE);

        /*
         * Start validation of the data that has been read.
         */
        mac = rt2x00_eeprom_addr(rt2x00dev, EEPROM_MAC_ADDR_0);
        rt2x00lib_set_mac_address(rt2x00dev, mac);

        word = rt2x00_eeprom_read(rt2x00dev, EEPROM_ANTENNA);
        if (word == 0xffff) {
                rt2x00_set_field16(&word, EEPROM_ANTENNA_NUM, 2);
                rt2x00_set_field16(&word, EEPROM_ANTENNA_TX_DEFAULT,
                                   ANTENNA_SW_DIVERSITY);
                rt2x00_set_field16(&word, EEPROM_ANTENNA_RX_DEFAULT,
                                   ANTENNA_SW_DIVERSITY);
                rt2x00_set_field16(&word, EEPROM_ANTENNA_LED_MODE,
                                   LED_MODE_DEFAULT);
                rt2x00_set_field16(&word, EEPROM_ANTENNA_DYN_TXAGC, 0);
                rt2x00_set_field16(&word, EEPROM_ANTENNA_HARDWARE_RADIO, 0);
                rt2x00_set_field16(&word, EEPROM_ANTENNA_RF_TYPE, RF2522);
                rt2x00_eeprom_write(rt2x00dev, EEPROM_ANTENNA, word);
                rt2x00_eeprom_dbg(rt2x00dev, "Antenna: 0x%04x\n", word);
        }

        word = rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC);
        if (word == 0xffff) {
                rt2x00_set_field16(&word, EEPROM_NIC_CARDBUS_ACCEL, 0);
                rt2x00_set_field16(&word, EEPROM_NIC_DYN_BBP_TUNE, 0);
                rt2x00_set_field16(&word, EEPROM_NIC_CCK_TX_POWER, 0);
                rt2x00_eeprom_write(rt2x00dev, EEPROM_NIC, word);
                rt2x00_eeprom_dbg(rt2x00dev, "NIC: 0x%04x\n", word);
        }

        word = rt2x00_eeprom_read(rt2x00dev, EEPROM_CALIBRATE_OFFSET);
        if (word == 0xffff) {
                rt2x00_set_field16(&word, EEPROM_CALIBRATE_OFFSET_RSSI,
                                   DEFAULT_RSSI_OFFSET);
                rt2x00_eeprom_write(rt2x00dev, EEPROM_CALIBRATE_OFFSET, word);
                rt2x00_eeprom_dbg(rt2x00dev, "Calibrate offset: 0x%04x\n",
                                  word);
        }

        word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE);
        if (word == 0xffff) {
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_THRESHOLD, 45);
                rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE, word);
                rt2x00_eeprom_dbg(rt2x00dev, "BBPtune: 0x%04x\n", word);
        }

        /*
         * Switch lower vgc bound to current BBP R17 value,
         * lower the value a bit for better quality.
         */
        bbp = rt2500usb_bbp_read(rt2x00dev, 17);
        bbp -= 6;

        word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_VGC);
        if (word == 0xffff) {
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCUPPER, 0x40);
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp);
                rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word);
                rt2x00_eeprom_dbg(rt2x00dev, "BBPtune vgc: 0x%04x\n", word);
        } else {
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp);
                rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word);
        }

        word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R17);
        if (word == 0xffff) {
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_R17_LOW, 0x48);
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_R17_HIGH, 0x41);
                rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R17, word);
                rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r17: 0x%04x\n", word);
        }

        word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R24);
        if (word == 0xffff) {
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_R24_LOW, 0x40);
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_R24_HIGH, 0x80);
                rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R24, word);
                rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r24: 0x%04x\n", word);
        }

        word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R25);
        if (word == 0xffff) {
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_R25_LOW, 0x40);
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_R25_HIGH, 0x50);
                rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R25, word);
                rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r25: 0x%04x\n", word);
        }

        word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R61);
        if (word == 0xffff) {
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_R61_LOW, 0x60);
                rt2x00_set_field16(&word, EEPROM_BBPTUNE_R61_HIGH, 0x6d);
                rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R61, word);
                rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r61: 0x%04x\n", word);
        }

        return 0;
}

static int rt2500usb_init_eeprom(struct rt2x00_dev *rt2x00dev)
{
        u16 reg;
        u16 value;
        u16 eeprom;

        /*
         * Read EEPROM word for configuration.
         */
        eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_ANTENNA);

        /*
         * Identify RF chipset.
         */
        value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RF_TYPE);
        reg = rt2500usb_register_read(rt2x00dev, MAC_CSR0);
        rt2x00_set_chip(rt2x00dev, RT2570, value, reg);

        if (((reg & 0xfff0) != 0) || ((reg & 0x0000000f) == 0)) {
                rt2x00_err(rt2x00dev, "Invalid RT chipset detected\n");
                return -ENODEV;
        }

        if (!rt2x00_rf(rt2x00dev, RF2522) &&
            !rt2x00_rf(rt2x00dev, RF2523) &&
            !rt2x00_rf(rt2x00dev, RF2524) &&
            !rt2x00_rf(rt2x00dev, RF2525) &&
            !rt2x00_rf(rt2x00dev, RF2525E) &&
            !rt2x00_rf(rt2x00dev, RF5222)) {
                rt2x00_err(rt2x00dev, "Invalid RF chipset detected\n");
                return -ENODEV;
        }

        /*
         * Identify default antenna configuration.
         */
        rt2x00dev->default_ant.tx =
            rt2x00_get_field16(eeprom, EEPROM_ANTENNA_TX_DEFAULT);
        rt2x00dev->default_ant.rx =
            rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RX_DEFAULT);

        /*
         * When the eeprom indicates SW_DIVERSITY use HW_DIVERSITY instead.
         * I am not 100% sure about this, but the legacy drivers do not
         * indicate antenna swapping in software is required when
         * diversity is enabled.
         */
        if (rt2x00dev->default_ant.tx == ANTENNA_SW_DIVERSITY)
                rt2x00dev->default_ant.tx = ANTENNA_HW_DIVERSITY;
        if (rt2x00dev->default_ant.rx == ANTENNA_SW_DIVERSITY)
                rt2x00dev->default_ant.rx = ANTENNA_HW_DIVERSITY;

        /*
         * Store led mode, for correct led behaviour.
         */
#ifdef CONFIG_RT2X00_LIB_LEDS
        value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_LED_MODE);

        rt2500usb_init_led(rt2x00dev, &rt2x00dev->led_radio, LED_TYPE_RADIO);
        if (value == LED_MODE_TXRX_ACTIVITY ||
            value == LED_MODE_DEFAULT ||
            value == LED_MODE_ASUS)
                rt2500usb_init_led(rt2x00dev, &rt2x00dev->led_qual,
                                   LED_TYPE_ACTIVITY);
#endif /* CONFIG_RT2X00_LIB_LEDS */

        /*
         * Detect if this device has an hardware controlled radio.
         */
        if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_HARDWARE_RADIO))
                __set_bit(CAPABILITY_HW_BUTTON, &rt2x00dev->cap_flags);

        /*
         * Read the RSSI <-> dBm offset information.
         */
        eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_CALIBRATE_OFFSET);
        rt2x00dev->rssi_offset =
            rt2x00_get_field16(eeprom, EEPROM_CALIBRATE_OFFSET_RSSI);

        return 0;
}

/*
 * RF value list for RF2522
 * Supports: 2.4 GHz
 */
static const struct rf_channel rf_vals_bg_2522[] = {
        { 1,  0x00002050, 0x000c1fda, 0x00000101, 0 },
        { 2,  0x00002050, 0x000c1fee, 0x00000101, 0 },
        { 3,  0x00002050, 0x000c2002, 0x00000101, 0 },
        { 4,  0x00002050, 0x000c2016, 0x00000101, 0 },
        { 5,  0x00002050, 0x000c202a, 0x00000101, 0 },
        { 6,  0x00002050, 0x000c203e, 0x00000101, 0 },
        { 7,  0x00002050, 0x000c2052, 0x00000101, 0 },
        { 8,  0x00002050, 0x000c2066, 0x00000101, 0 },
        { 9,  0x00002050, 0x000c207a, 0x00000101, 0 },
        { 10, 0x00002050, 0x000c208e, 0x00000101, 0 },
        { 11, 0x00002050, 0x000c20a2, 0x00000101, 0 },
        { 12, 0x00002050, 0x000c20b6, 0x00000101, 0 },
        { 13, 0x00002050, 0x000c20ca, 0x00000101, 0 },
        { 14, 0x00002050, 0x000c20fa, 0x00000101, 0 },
};

/*
 * RF value list for RF2523
 * Supports: 2.4 GHz
 */
static const struct rf_channel rf_vals_bg_2523[] = {
        { 1,  0x00022010, 0x00000c9e, 0x000e0111, 0x00000a1b },
        { 2,  0x00022010, 0x00000ca2, 0x000e0111, 0x00000a1b },
        { 3,  0x00022010, 0x00000ca6, 0x000e0111, 0x00000a1b },
        { 4,  0x00022010, 0x00000caa, 0x000e0111, 0x00000a1b },
        { 5,  0x00022010, 0x00000cae, 0x000e0111, 0x00000a1b },
        { 6,  0x00022010, 0x00000cb2, 0x000e0111, 0x00000a1b },
        { 7,  0x00022010, 0x00000cb6, 0x000e0111, 0x00000a1b },
        { 8,  0x00022010, 0x00000cba, 0x000e0111, 0x00000a1b },
        { 9,  0x00022010, 0x00000cbe, 0x000e0111, 0x00000a1b },
        { 10, 0x00022010, 0x00000d02, 0x000e0111, 0x00000a1b },
        { 11, 0x00022010, 0x00000d06, 0x000e0111, 0x00000a1b },
        { 12, 0x00022010, 0x00000d0a, 0x000e0111, 0x00000a1b },
        { 13, 0x00022010, 0x00000d0e, 0x000e0111, 0x00000a1b },
        { 14, 0x00022010, 0x00000d1a, 0x000e0111, 0x00000a03 },
};

/*
 * RF value list for RF2524
 * Supports: 2.4 GHz
 */
static const struct rf_channel rf_vals_bg_2524[] = {
        { 1,  0x00032020, 0x00000c9e, 0x00000101, 0x00000a1b },
        { 2,  0x00032020, 0x00000ca2, 0x00000101, 0x00000a1b },
        { 3,  0x00032020, 0x00000ca6, 0x00000101, 0x00000a1b },
        { 4,  0x00032020, 0x00000caa, 0x00000101, 0x00000a1b },
        { 5,  0x00032020, 0x00000cae, 0x00000101, 0x00000a1b },
        { 6,  0x00032020, 0x00000cb2, 0x00000101, 0x00000a1b },
        { 7,  0x00032020, 0x00000cb6, 0x00000101, 0x00000a1b },
        { 8,  0x00032020, 0x00000cba, 0x00000101, 0x00000a1b },
        { 9,  0x00032020, 0x00000cbe, 0x00000101, 0x00000a1b },
        { 10, 0x00032020, 0x00000d02, 0x00000101, 0x00000a1b },
        { 11, 0x00032020, 0x00000d06, 0x00000101, 0x00000a1b },
        { 12, 0x00032020, 0x00000d0a, 0x00000101, 0x00000a1b },
        { 13, 0x00032020, 0x00000d0e, 0x00000101, 0x00000a1b },
        { 14, 0x00032020, 0x00000d1a, 0x00000101, 0x00000a03 },
};

/*
 * RF value list for RF2525
 * Supports: 2.4 GHz
 */
static const struct rf_channel rf_vals_bg_2525[] = {
        { 1,  0x00022020, 0x00080c9e, 0x00060111, 0x00000a1b },
        { 2,  0x00022020, 0x00080ca2, 0x00060111, 0x00000a1b },
        { 3,  0x00022020, 0x00080ca6, 0x00060111, 0x00000a1b },
        { 4,  0x00022020, 0x00080caa, 0x00060111, 0x00000a1b },
        { 5,  0x00022020, 0x00080cae, 0x00060111, 0x00000a1b },
        { 6,  0x00022020, 0x00080cb2, 0x00060111, 0x00000a1b },
        { 7,  0x00022020, 0x00080cb6, 0x00060111, 0x00000a1b },
        { 8,  0x00022020, 0x00080cba, 0x00060111, 0x00000a1b },
        { 9,  0x00022020, 0x00080cbe, 0x00060111, 0x00000a1b },
        { 10, 0x00022020, 0x00080d02, 0x00060111, 0x00000a1b },
        { 11, 0x00022020, 0x00080d06, 0x00060111, 0x00000a1b },
        { 12, 0x00022020, 0x00080d0a, 0x00060111, 0x00000a1b },
        { 13, 0x00022020, 0x00080d0e, 0x00060111, 0x00000a1b },
        { 14, 0x00022020, 0x00080d1a, 0x00060111, 0x00000a03 },
};

/*
 * RF value list for RF2525e
 * Supports: 2.4 GHz
 */
static const struct rf_channel rf_vals_bg_2525e[] = {
        { 1,  0x00022010, 0x0000089a, 0x00060111, 0x00000e1b },
        { 2,  0x00022010, 0x0000089e, 0x00060111, 0x00000e07 },
        { 3,  0x00022010, 0x0000089e, 0x00060111, 0x00000e1b },
        { 4,  0x00022010, 0x000008a2, 0x00060111, 0x00000e07 },
        { 5,  0x00022010, 0x000008a2, 0x00060111, 0x00000e1b },
        { 6,  0x00022010, 0x000008a6, 0x00060111, 0x00000e07 },
        { 7,  0x00022010, 0x000008a6, 0x00060111, 0x00000e1b },
        { 8,  0x00022010, 0x000008aa, 0x00060111, 0x00000e07 },
        { 9,  0x00022010, 0x000008aa, 0x00060111, 0x00000e1b },
        { 10, 0x00022010, 0x000008ae, 0x00060111, 0x00000e07 },
        { 11, 0x00022010, 0x000008ae, 0x00060111, 0x00000e1b },
        { 12, 0x00022010, 0x000008b2, 0x00060111, 0x00000e07 },
        { 13, 0x00022010, 0x000008b2, 0x00060111, 0x00000e1b },
        { 14, 0x00022010, 0x000008b6, 0x00060111, 0x00000e23 },
};

/*
 * RF value list for RF5222
 * Supports: 2.4 GHz & 5.2 GHz
 */
static const struct rf_channel rf_vals_5222[] = {
        { 1,  0x00022020, 0x00001136, 0x00000101, 0x00000a0b },
        { 2,  0x00022020, 0x0000113a, 0x00000101, 0x00000a0b },
        { 3,  0x00022020, 0x0000113e, 0x00000101, 0x00000a0b },
        { 4,  0x00022020, 0x00001182, 0x00000101, 0x00000a0b },
        { 5,  0x00022020, 0x00001186, 0x00000101, 0x00000a0b },
        { 6,  0x00022020, 0x0000118a, 0x00000101, 0x00000a0b },
        { 7,  0x00022020, 0x0000118e, 0x00000101, 0x00000a0b },
        { 8,  0x00022020, 0x00001192, 0x00000101, 0x00000a0b },
        { 9,  0x00022020, 0x00001196, 0x00000101, 0x00000a0b },
        { 10, 0x00022020, 0x0000119a, 0x00000101, 0x00000a0b },
        { 11, 0x00022020, 0x0000119e, 0x00000101, 0x00000a0b },
        { 12, 0x00022020, 0x000011a2, 0x00000101, 0x00000a0b },
        { 13, 0x00022020, 0x000011a6, 0x00000101, 0x00000a0b },
        { 14, 0x00022020, 0x000011ae, 0x00000101, 0x00000a1b },

        /* 802.11 UNI / HyperLan 2 */
        { 36, 0x00022010, 0x00018896, 0x00000101, 0x00000a1f },
        { 40, 0x00022010, 0x0001889a, 0x00000101, 0x00000a1f },
        { 44, 0x00022010, 0x0001889e, 0x00000101, 0x00000a1f },
        { 48, 0x00022010, 0x000188a2, 0x00000101, 0x00000a1f },
        { 52, 0x00022010, 0x000188a6, 0x00000101, 0x00000a1f },
        { 66, 0x00022010, 0x000188aa, 0x00000101, 0x00000a1f },
        { 60, 0x00022010, 0x000188ae, 0x00000101, 0x00000a1f },
        { 64, 0x00022010, 0x000188b2, 0x00000101, 0x00000a1f },

        /* 802.11 HyperLan 2 */
        { 100, 0x00022010, 0x00008802, 0x00000101, 0x00000a0f },
        { 104, 0x00022010, 0x00008806, 0x00000101, 0x00000a0f },
        { 108, 0x00022010, 0x0000880a, 0x00000101, 0x00000a0f },
        { 112, 0x00022010, 0x0000880e, 0x00000101, 0x00000a0f },
        { 116, 0x00022010, 0x00008812, 0x00000101, 0x00000a0f },
        { 120, 0x00022010, 0x00008816, 0x00000101, 0x00000a0f },
        { 124, 0x00022010, 0x0000881a, 0x00000101, 0x00000a0f },
        { 128, 0x00022010, 0x0000881e, 0x00000101, 0x00000a0f },
        { 132, 0x00022010, 0x00008822, 0x00000101, 0x00000a0f },
        { 136, 0x00022010, 0x00008826, 0x00000101, 0x00000a0f },

        /* 802.11 UNII */
        { 140, 0x00022010, 0x0000882a, 0x00000101, 0x00000a0f },
        { 149, 0x00022020, 0x000090a6, 0x00000101, 0x00000a07 },
        { 153, 0x00022020, 0x000090ae, 0x00000101, 0x00000a07 },
        { 157, 0x00022020, 0x000090b6, 0x00000101, 0x00000a07 },
        { 161, 0x00022020, 0x000090be, 0x00000101, 0x00000a07 },
};

static int rt2500usb_probe_hw_mode(struct rt2x00_dev *rt2x00dev)
{
        struct hw_mode_spec *spec = &rt2x00dev->spec;
        struct channel_info *info;
        char *tx_power;
        unsigned int i;

        /*
         * Initialize all hw fields.
         *
         * Don't set IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING unless we are
         * capable of sending the buffered frames out after the DTIM
         * transmission using rt2x00lib_beacondone. This will send out
         * multicast and broadcast traffic immediately instead of buffering it
         * infinitly and thus dropping it after some time.
         */
        ieee80211_hw_set(rt2x00dev->hw, PS_NULLFUNC_STACK);
        ieee80211_hw_set(rt2x00dev->hw, SUPPORTS_PS);
        ieee80211_hw_set(rt2x00dev->hw, RX_INCLUDES_FCS);
        ieee80211_hw_set(rt2x00dev->hw, SIGNAL_DBM);

        /*
         * Disable powersaving as default.
         */
        rt2x00dev->hw->wiphy->flags &= ~WIPHY_FLAG_PS_ON_BY_DEFAULT;

        SET_IEEE80211_DEV(rt2x00dev->hw, rt2x00dev->dev);
        SET_IEEE80211_PERM_ADDR(rt2x00dev->hw,
                                rt2x00_eeprom_addr(rt2x00dev,
                                                   EEPROM_MAC_ADDR_0));

        /*
         * Initialize hw_mode information.
         */
        spec->supported_bands = SUPPORT_BAND_2GHZ;
        spec->supported_rates = SUPPORT_RATE_CCK | SUPPORT_RATE_OFDM;

        if (rt2x00_rf(rt2x00dev, RF2522)) {
                spec->num_channels = ARRAY_SIZE(rf_vals_bg_2522);
                spec->channels = rf_vals_bg_2522;
        } else if (rt2x00_rf(rt2x00dev, RF2523)) {
                spec->num_channels = ARRAY_SIZE(rf_vals_bg_2523);
                spec->channels = rf_vals_bg_2523;
        } else if (rt2x00_rf(rt2x00dev, RF2524)) {
                spec->num_channels = ARRAY_SIZE(rf_vals_bg_2524);
                spec->channels = rf_vals_bg_2524;
        } else if (rt2x00_rf(rt2x00dev, RF2525)) {
                spec->num_channels = ARRAY_SIZE(rf_vals_bg_2525);
                spec->channels = rf_vals_bg_2525;
        } else if (rt2x00_rf(rt2x00dev, RF2525E)) {
                spec->num_channels = ARRAY_SIZE(rf_vals_bg_2525e);
                spec->channels = rf_vals_bg_2525e;
        } else if (rt2x00_rf(rt2x00dev, RF5222)) {
                spec->supported_bands |= SUPPORT_BAND_5GHZ;
                spec->num_channels = ARRAY_SIZE(rf_vals_5222);
                spec->channels = rf_vals_5222;
        }

        /*
         * Create channel information array
         */
        info = kcalloc(spec->num_channels, sizeof(*info), GFP_KERNEL);
        if (!info)
                return -ENOMEM;

        spec->channels_info = info;

        tx_power = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_START);
        for (i = 0; i < 14; i++) {
                info[i].max_power = MAX_TXPOWER;
                info[i].default_power1 = TXPOWER_FROM_DEV(tx_power[i]);
        }

        if (spec->num_channels > 14) {
                for (i = 14; i < spec->num_channels; i++) {
                        info[i].max_power = MAX_TXPOWER;
                        info[i].default_power1 = DEFAULT_TXPOWER;
                }
        }

        return 0;
}

static int rt2500usb_probe_hw(struct rt2x00_dev *rt2x00dev)
{
        int retval;
        u16 reg;

        /*
         * Allocate eeprom data.
         */
        retval = rt2500usb_validate_eeprom(rt2x00dev);
        if (retval)
                return retval;

        retval = rt2500usb_init_eeprom(rt2x00dev);
        if (retval)
                return retval;

        /*
         * Enable rfkill polling by setting GPIO direction of the
         * rfkill switch GPIO pin correctly.
         */
        reg = rt2500usb_register_read(rt2x00dev, MAC_CSR19);
        rt2x00_set_field16(&reg, MAC_CSR19_DIR0, 0);
        rt2500usb_register_write(rt2x00dev, MAC_CSR19, reg);

        /*
         * Initialize hw specifications.
         */
        retval = rt2500usb_probe_hw_mode(rt2x00dev);
        if (retval)
                return retval;

        /*
         * This device requires the atim queue
         */
        __set_bit(REQUIRE_ATIM_QUEUE, &rt2x00dev->cap_flags);
        __set_bit(REQUIRE_BEACON_GUARD, &rt2x00dev->cap_flags);
        if (!modparam_nohwcrypt) {
                __set_bit(CAPABILITY_HW_CRYPTO, &rt2x00dev->cap_flags);
                __set_bit(REQUIRE_COPY_IV, &rt2x00dev->cap_flags);
        }
        __set_bit(REQUIRE_SW_SEQNO, &rt2x00dev->cap_flags);
        __set_bit(REQUIRE_PS_AUTOWAKE, &rt2x00dev->cap_flags);

        /*
         * Set the rssi offset.
         */
        rt2x00dev->rssi_offset = DEFAULT_RSSI_OFFSET;

        return 0;
}

static const struct ieee80211_ops rt2500usb_mac80211_ops = {
        .tx                     = rt2x00mac_tx,
        .start                  = rt2x00mac_start,
        .stop                   = rt2x00mac_stop,
        .add_interface          = rt2x00mac_add_interface,
        .remove_interface       = rt2x00mac_remove_interface,
        .config                 = rt2x00mac_config,
        .configure_filter       = rt2x00mac_configure_filter,
        .set_tim                = rt2x00mac_set_tim,
        .set_key                = rt2x00mac_set_key,
        .sw_scan_start          = rt2x00mac_sw_scan_start,
        .sw_scan_complete       = rt2x00mac_sw_scan_complete,
        .get_stats              = rt2x00mac_get_stats,
        .bss_info_changed       = rt2x00mac_bss_info_changed,
        .conf_tx                = rt2x00mac_conf_tx,
        .rfkill_poll            = rt2x00mac_rfkill_poll,
        .flush                  = rt2x00mac_flush,
        .set_antenna            = rt2x00mac_set_antenna,
        .get_antenna            = rt2x00mac_get_antenna,
        .get_ringparam          = rt2x00mac_get_ringparam,
        .tx_frames_pending      = rt2x00mac_tx_frames_pending,
};

static const struct rt2x00lib_ops rt2500usb_rt2x00_ops = {
        .probe_hw               = rt2500usb_probe_hw,
        .initialize             = rt2x00usb_initialize,
        .uninitialize           = rt2x00usb_uninitialize,
        .clear_entry            = rt2x00usb_clear_entry,
        .set_device_state       = rt2500usb_set_device_state,
        .rfkill_poll            = rt2500usb_rfkill_poll,
        .link_stats             = rt2500usb_link_stats,
        .reset_tuner            = rt2500usb_reset_tuner,
        .watchdog               = rt2x00usb_watchdog,
        .start_queue            = rt2500usb_start_queue,
        .kick_queue             = rt2x00usb_kick_queue,
        .stop_queue             = rt2500usb_stop_queue,
        .flush_queue            = rt2x00usb_flush_queue,
        .write_tx_desc          = rt2500usb_write_tx_desc,
        .write_beacon           = rt2500usb_write_beacon,
        .get_tx_data_len        = rt2500usb_get_tx_data_len,
        .fill_rxdone            = rt2500usb_fill_rxdone,
        .config_shared_key      = rt2500usb_config_key,
        .config_pairwise_key    = rt2500usb_config_key,
        .config_filter          = rt2500usb_config_filter,
        .config_intf            = rt2500usb_config_intf,
        .config_erp             = rt2500usb_config_erp,
        .config_ant             = rt2500usb_config_ant,
        .config                 = rt2500usb_config,
};

static void rt2500usb_queue_init(struct data_queue *queue)
{
        switch (queue->qid) {
        case QID_RX:
                queue->limit = 32;
                queue->data_size = DATA_FRAME_SIZE;
                queue->desc_size = RXD_DESC_SIZE;
                queue->priv_size = sizeof(struct queue_entry_priv_usb);
                break;

        case QID_AC_VO:
        case QID_AC_VI:
        case QID_AC_BE:
        case QID_AC_BK:
                queue->limit = 32;
                queue->data_size = DATA_FRAME_SIZE;
                queue->desc_size = TXD_DESC_SIZE;
                queue->priv_size = sizeof(struct queue_entry_priv_usb);
                break;

        case QID_BEACON:
                queue->limit = 1;
                queue->data_size = MGMT_FRAME_SIZE;
                queue->desc_size = TXD_DESC_SIZE;
                queue->priv_size = sizeof(struct queue_entry_priv_usb_bcn);
                break;

        case QID_ATIM:
                queue->limit = 8;
                queue->data_size = DATA_FRAME_SIZE;
                queue->desc_size = TXD_DESC_SIZE;
                queue->priv_size = sizeof(struct queue_entry_priv_usb);
                break;

        default:
                BUG();
                break;
        }
}

static const struct rt2x00_ops rt2500usb_ops = {
        .name                   = KBUILD_MODNAME,
        .max_ap_intf            = 1,
        .eeprom_size            = EEPROM_SIZE,
        .rf_size                = RF_SIZE,
        .tx_queues              = NUM_TX_QUEUES,
        .queue_init             = rt2500usb_queue_init,
        .lib                    = &rt2500usb_rt2x00_ops,
        .hw                     = &rt2500usb_mac80211_ops,
#ifdef CONFIG_RT2X00_LIB_DEBUGFS
        .debugfs                = &rt2500usb_rt2x00debug,
#endif /* CONFIG_RT2X00_LIB_DEBUGFS */
};

/*
 * rt2500usb module information.
 */
static const struct usb_device_id rt2500usb_device_table[] = {
        /* ASUS */
        { USB_DEVICE(0x0b05, 0x1706) },
        { USB_DEVICE(0x0b05, 0x1707) },
        /* Belkin */
        { USB_DEVICE(0x050d, 0x7050) }, /* FCC ID: K7SF5D7050A ver. 2.x */
        { USB_DEVICE(0x050d, 0x7051) },
        /* Cisco Systems */
        { USB_DEVICE(0x13b1, 0x000d) },
        { USB_DEVICE(0x13b1, 0x0011) },
        { USB_DEVICE(0x13b1, 0x001a) },
        /* Conceptronic */
        { USB_DEVICE(0x14b2, 0x3c02) },
        /* D-LINK */
        { USB_DEVICE(0x2001, 0x3c00) },
        /* Gigabyte */
        { USB_DEVICE(0x1044, 0x8001) },
        { USB_DEVICE(0x1044, 0x8007) },
        /* Hercules */
        { USB_DEVICE(0x06f8, 0xe000) },
        /* Melco */
        { USB_DEVICE(0x0411, 0x005e) },
        { USB_DEVICE(0x0411, 0x0066) },
        { USB_DEVICE(0x0411, 0x0067) },
        { USB_DEVICE(0x0411, 0x008b) },
        { USB_DEVICE(0x0411, 0x0097) },
        /* MSI */
        { USB_DEVICE(0x0db0, 0x6861) },
        { USB_DEVICE(0x0db0, 0x6865) },
        { USB_DEVICE(0x0db0, 0x6869) },
        /* Ralink */
        { USB_DEVICE(0x148f, 0x1706) },
        { USB_DEVICE(0x148f, 0x2570) },
        { USB_DEVICE(0x148f, 0x9020) },
        /* Sagem */
        { USB_DEVICE(0x079b, 0x004b) },
        /* Siemens */
        { USB_DEVICE(0x0681, 0x3c06) },
        /* SMC */
        { USB_DEVICE(0x0707, 0xee13) },
        /* Spairon */
        { USB_DEVICE(0x114b, 0x0110) },
        /* SURECOM */
        { USB_DEVICE(0x0769, 0x11f3) },
        /* Trust */
        { USB_DEVICE(0x0eb0, 0x9020) },
        /* VTech */
        { USB_DEVICE(0x0f88, 0x3012) },
        /* Zinwell */
        { USB_DEVICE(0x5a57, 0x0260) },
        { 0, }
};

MODULE_AUTHOR(DRV_PROJECT);
MODULE_VERSION(DRV_VERSION);
MODULE_DESCRIPTION("Ralink RT2500 USB Wireless LAN driver.");
MODULE_DEVICE_TABLE(usb, rt2500usb_device_table);
MODULE_LICENSE("GPL");

static int rt2500usb_probe(struct usb_interface *usb_intf,
                           const struct usb_device_id *id)
{
        return rt2x00usb_probe(usb_intf, &rt2500usb_ops);
}

static struct usb_driver rt2500usb_driver = {
        .name           = KBUILD_MODNAME,
        .id_table       = rt2500usb_device_table,
        .probe          = rt2500usb_probe,
        .disconnect     = rt2x00usb_disconnect,
        .suspend        = rt2x00usb_suspend,
        .resume         = rt2x00usb_resume,
        .reset_resume   = rt2x00usb_resume,
        .disable_hub_initiated_lpm = 1,
};

module_usb_driver(rt2500usb_driver);