// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * arch/arm/mach-iop32x/iq31244.c
 *
 * Board support code for the Intel EP80219 and IQ31244 platforms.
 *
 * Author: Rory Bolt <rorybolt@pacbell.net>
 * Copyright (C) 2002 Rory Bolt
 * Copyright 2003 (c) MontaVista, Software, Inc.
 * Copyright (C) 2004 Intel Corp.
 */

#include <linux/mm.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/pm.h>
#include <linux/string.h>
#include <linux/serial_core.h>
#include <linux/serial_8250.h>
#include <linux/mtd/physmap.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/gpio/machine.h>
#include <asm/cputype.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/pci.h>
#include <asm/mach/time.h>
#include <asm/mach-types.h>
#include <asm/page.h>

#include "hardware.h"
#include "irqs.h"
#include "gpio-iop32x.h"

/*
 * Until March of 2007 iq31244 platforms and ep80219 platforms shared the
 * same machine id, and the processor type was used to select board type.
 * However this assumption breaks for an iq80219 board which is an iop219
 * processor on an iq31244 board.  The force_ep80219 flag has been added
 * for old boot loaders using the iq31244 machine id for an ep80219 platform.
 */
static int force_ep80219;

static int is_80219(void)
{
        return !!((read_cpuid_id() & 0xffffffe0) == 0x69052e20);
}

static int is_ep80219(void)
{
        if (machine_is_ep80219() || force_ep80219)
                return 1;
        else
                return 0;
}


/*
 * EP80219/IQ31244 timer tick configuration.
 */
static void __init iq31244_timer_init(void)
{
        if (is_ep80219()) {
                /* 33.333 MHz crystal.  */
                iop_init_time(200000000);
        } else {
                /* 33.000 MHz crystal.  */
                iop_init_time(198000000);
        }
}


/*
 * IQ31244 I/O.
 */
static struct map_desc iq31244_io_desc[] __initdata = {
        {       /* on-board devices */
                .virtual        = IQ31244_UART,
                .pfn            = __phys_to_pfn(IQ31244_UART),
                .length         = 0x00100000,
                .type           = MT_DEVICE,
        },
};

void __init iq31244_map_io(void)
{
        iop3xx_map_io();
        iotable_init(iq31244_io_desc, ARRAY_SIZE(iq31244_io_desc));
}


/*
 * EP80219/IQ31244 PCI.
 */
static int __init
ep80219_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
{
        int irq;

        if (slot == 0) {
                /* CFlash */
                irq = IRQ_IOP32X_XINT1;
        } else if (slot == 1) {
                /* 82551 Pro 100 */
                irq = IRQ_IOP32X_XINT0;
        } else if (slot == 2) {
                /* PCI-X Slot */
                irq = IRQ_IOP32X_XINT3;
        } else if (slot == 3) {
                /* SATA */
                irq = IRQ_IOP32X_XINT2;
        } else {
                printk(KERN_ERR "ep80219_pci_map_irq() called for unknown "
                        "device PCI:%d:%d:%d\n", dev->bus->number,
                        PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
                irq = -1;
        }

        return irq;
}

static struct hw_pci ep80219_pci __initdata = {
        .nr_controllers = 1,
        .ops            = &iop3xx_ops,
        .setup          = iop3xx_pci_setup,
        .preinit        = iop3xx_pci_preinit,
        .map_irq        = ep80219_pci_map_irq,
};

static int __init
iq31244_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
{
        int irq;

        if (slot == 0) {
                /* CFlash */
                irq = IRQ_IOP32X_XINT1;
        } else if (slot == 1) {
                /* SATA */
                irq = IRQ_IOP32X_XINT2;
        } else if (slot == 2) {
                /* PCI-X Slot */
                irq = IRQ_IOP32X_XINT3;
        } else if (slot == 3) {
                /* 82546 GigE */
                irq = IRQ_IOP32X_XINT0;
        } else {
                printk(KERN_ERR "iq31244_pci_map_irq called for unknown "
                        "device PCI:%d:%d:%d\n", dev->bus->number,
                        PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
                irq = -1;
        }

        return irq;
}

static struct hw_pci iq31244_pci __initdata = {
        .nr_controllers = 1,
        .ops            = &iop3xx_ops,
        .setup          = iop3xx_pci_setup,
        .preinit        = iop3xx_pci_preinit,
        .map_irq        = iq31244_pci_map_irq,
};

static int __init iq31244_pci_init(void)
{
        if (is_ep80219())
                pci_common_init(&ep80219_pci);
        else if (machine_is_iq31244()) {
                if (is_80219()) {
                        printk("note: iq31244 board type has been selected\n");
                        printk("note: to select ep80219 operation:\n");
                        printk("\t1/ specify \"force_ep80219\" on the kernel"
                                " command line\n");
                        printk("\t2/ update boot loader to pass"
                                " the ep80219 id: %d\n", MACH_TYPE_EP80219);
                }
                pci_common_init(&iq31244_pci);
        }

        return 0;
}

subsys_initcall(iq31244_pci_init);


/*
 * IQ31244 machine initialisation.
 */
static struct physmap_flash_data iq31244_flash_data = {
        .width          = 2,
};

static struct resource iq31244_flash_resource = {
        .start          = 0xf0000000,
        .end            = 0xf07fffff,
        .flags          = IORESOURCE_MEM,
};

static struct platform_device iq31244_flash_device = {
        .name           = "physmap-flash",
        .id             = 0,
        .dev            = {
                .platform_data  = &iq31244_flash_data,
        },
        .num_resources  = 1,
        .resource       = &iq31244_flash_resource,
};

static struct plat_serial8250_port iq31244_serial_port[] = {
        {
                .mapbase        = IQ31244_UART,
                .membase        = (char *)IQ31244_UART,
                .irq            = IRQ_IOP32X_XINT1,
                .flags          = UPF_SKIP_TEST,
                .iotype         = UPIO_MEM,
                .regshift       = 0,
                .uartclk        = 1843200,
        },
        { },
};

static struct resource iq31244_uart_resource = {
        .start          = IQ31244_UART,
        .end            = IQ31244_UART + 7,
        .flags          = IORESOURCE_MEM,
};

static struct platform_device iq31244_serial_device = {
        .name           = "serial8250",
        .id             = PLAT8250_DEV_PLATFORM,
        .dev            = {
                .platform_data          = iq31244_serial_port,
        },
        .num_resources  = 1,
        .resource       = &iq31244_uart_resource,
};

/*
 * This function will send a SHUTDOWN_COMPLETE message to the PIC
 * controller over I2C.  We are not using the i2c subsystem since
 * we are going to power off and it may be removed
 */
void ep80219_power_off(void)
{
        /*
         * Send the Address byte w/ the start condition
         */
        *IOP3XX_IDBR1 = 0x60;
        *IOP3XX_ICR1 = 0xE9;
        mdelay(1);

        /*
         * Send the START_MSG byte w/ no start or stop condition
         */
        *IOP3XX_IDBR1 = 0x0F;
        *IOP3XX_ICR1 = 0xE8;
        mdelay(1);

        /*
         * Send the SHUTDOWN_COMPLETE Message ID byte w/ no start or
         * stop condition
         */
        *IOP3XX_IDBR1 = 0x03;
        *IOP3XX_ICR1 = 0xE8;
        mdelay(1);

        /*
         * Send an ignored byte w/ stop condition
         */
        *IOP3XX_IDBR1 = 0x00;
        *IOP3XX_ICR1 = 0xEA;

        while (1)
                ;
}

static void __init iq31244_init_machine(void)
{
        register_iop32x_gpio();
        gpiod_add_lookup_table(&iop3xx_i2c0_gpio_lookup);
        gpiod_add_lookup_table(&iop3xx_i2c1_gpio_lookup);
        platform_device_register(&iop3xx_i2c0_device);
        platform_device_register(&iop3xx_i2c1_device);
        platform_device_register(&iq31244_flash_device);
        platform_device_register(&iq31244_serial_device);
        platform_device_register(&iop3xx_dma_0_channel);
        platform_device_register(&iop3xx_dma_1_channel);

        if (is_ep80219())
                pm_power_off = ep80219_power_off;

        if (!is_80219())
                platform_device_register(&iop3xx_aau_channel);
}

static int __init force_ep80219_setup(char *str)
{
        force_ep80219 = 1;
        return 1;
}

__setup("force_ep80219", force_ep80219_setup);

MACHINE_START(IQ31244, "Intel IQ31244")
        /* Maintainer: Intel Corp. */
        .atag_offset    = 0x100,
        .map_io         = iq31244_map_io,
        .init_irq       = iop32x_init_irq,
        .init_time      = iq31244_timer_init,
        .init_machine   = iq31244_init_machine,
        .restart        = iop3xx_restart,
MACHINE_END

/* There should have been an ep80219 machine identifier from the beginning.
 * Boot roms older than March 2007 do not know the ep80219 machine id.  Pass
 * "force_ep80219" on the kernel command line, otherwise iq31244 operation
 * will be selected.
 */
MACHINE_START(EP80219, "Intel EP80219")
        /* Maintainer: Intel Corp. */
        .atag_offset    = 0x100,
        .map_io         = iq31244_map_io,
        .init_irq       = iop32x_init_irq,
        .init_time      = iq31244_timer_init,
        .init_machine   = iq31244_init_machine,
        .restart        = iop3xx_restart,
MACHINE_END