1/* SPDX-License-Identifier: GPL-2.0-only */ 2/* ------------------------------------------------------------------------- */ 3/* i2c-iop3xx.h algorithm driver definitions private to i2c-iop3xx.c */ 4/* ------------------------------------------------------------------------- */ 5/* Copyright (C) 2003 Peter Milne, D-TACQ Solutions Ltd 6 * <Peter dot Milne at D hyphen TACQ dot com> 7 8 */ 9/* ------------------------------------------------------------------------- */ 10 11 12#ifndef I2C_IOP3XX_H 13#define I2C_IOP3XX_H 1 14 15/* 16 * iop321 hardware bit definitions 17 */ 18#define IOP3XX_ICR_FAST_MODE 0x8000 /* 1=400kBps, 0=100kBps */ 19#define IOP3XX_ICR_UNIT_RESET 0x4000 /* 1=RESET */ 20#define IOP3XX_ICR_SAD_IE 0x2000 /* 1=Slave Detect Interrupt Enable */ 21#define IOP3XX_ICR_ALD_IE 0x1000 /* 1=Arb Loss Detect Interrupt Enable */ 22#define IOP3XX_ICR_SSD_IE 0x0800 /* 1=Slave STOP Detect Interrupt Enable */ 23#define IOP3XX_ICR_BERR_IE 0x0400 /* 1=Bus Error Interrupt Enable */ 24#define IOP3XX_ICR_RXFULL_IE 0x0200 /* 1=Receive Full Interrupt Enable */ 25#define IOP3XX_ICR_TXEMPTY_IE 0x0100 /* 1=Transmit Empty Interrupt Enable */ 26#define IOP3XX_ICR_GCD 0x0080 /* 1=General Call Disable */ 27/* 28 * IOP3XX_ICR_GCD: 1 disables response as slave. "This bit must be set 29 * when sending a master mode general call message from the I2C unit" 30 */ 31#define IOP3XX_ICR_UE 0x0040 /* 1=Unit Enable */ 32/* 33 * "NOTE: To avoid I2C bus integrity problems, 34 * the user needs to ensure that the GPIO Output Data Register - 35 * GPOD bits associated with an I2C port are cleared prior to setting 36 * the enable bit for that I2C serial port. 37 * The user prepares to enable I2C port 0 and 38 * I2C port 1 by clearing GPOD bits 7:6 and GPOD bits 5:4, respectively. 39 */ 40#define IOP3XX_ICR_SCLEN 0x0020 /* 1=SCL enable for master mode */ 41#define IOP3XX_ICR_MABORT 0x0010 /* 1=Send a STOP with no data 42 * NB TBYTE must be clear */ 43#define IOP3XX_ICR_TBYTE 0x0008 /* 1=Send/Receive a byte. i2c clears */ 44#define IOP3XX_ICR_NACK 0x0004 /* 1=reply with NACK */ 45#define IOP3XX_ICR_MSTOP 0x0002 /* 1=send a STOP after next data byte */ 46#define IOP3XX_ICR_MSTART 0x0001 /* 1=initiate a START */ 47 48 49#define IOP3XX_ISR_BERRD 0x0400 /* 1=BUS ERROR Detected */ 50#define IOP3XX_ISR_SAD 0x0200 /* 1=Slave ADdress Detected */ 51#define IOP3XX_ISR_GCAD 0x0100 /* 1=General Call Address Detected */ 52#define IOP3XX_ISR_RXFULL 0x0080 /* 1=Receive Full */ 53#define IOP3XX_ISR_TXEMPTY 0x0040 /* 1=Transmit Empty */ 54#define IOP3XX_ISR_ALD 0x0020 /* 1=Arbitration Loss Detected */ 55#define IOP3XX_ISR_SSD 0x0010 /* 1=Slave STOP Detected */ 56#define IOP3XX_ISR_BBUSY 0x0008 /* 1=Bus BUSY */ 57#define IOP3XX_ISR_UNITBUSY 0x0004 /* 1=Unit Busy */ 58#define IOP3XX_ISR_NACK 0x0002 /* 1=Unit Rx or Tx a NACK */ 59#define IOP3XX_ISR_RXREAD 0x0001 /* 1=READ 0=WRITE (R/W bit of slave addr */ 60 61#define IOP3XX_ISR_CLEARBITS 0x07f0 62 63#define IOP3XX_ISAR_SAMASK 0x007f 64 65#define IOP3XX_IDBR_MASK 0x00ff 66 67#define IOP3XX_IBMR_SCL 0x0002 68#define IOP3XX_IBMR_SDA 0x0001 69 70#define IOP3XX_GPOD_I2C0 0x00c0 /* clear these bits to enable ch0 */ 71#define IOP3XX_GPOD_I2C1 0x0030 /* clear these bits to enable ch1 */ 72 73#define MYSAR 0 /* default slave address */ 74 75#define I2C_ERR 321 76#define I2C_ERR_BERR (I2C_ERR+0) 77#define I2C_ERR_ALD (I2C_ERR+1) 78 79 80#define CR_OFFSET 0 81#define SR_OFFSET 0x4 82#define SAR_OFFSET 0x8 83#define DBR_OFFSET 0xc 84#define CCR_OFFSET 0x10 85#define BMR_OFFSET 0x14 86 87#define IOP3XX_I2C_IO_SIZE 0x18 88 89struct i2c_algo_iop3xx_data { 90 void __iomem *ioaddr; 91 wait_queue_head_t waitq; 92 spinlock_t lock; 93 u32 SR_enabled, SR_received; 94 int id; 95 struct gpio_desc *gpio_scl; 96 struct gpio_desc *gpio_sda; 97}; 98 99#endif /* I2C_IOP3XX_H */ 100