linux/drivers/pinctrl/nomadik/pinctrl-nomadik.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0-only
   2/*
   3 * Generic GPIO driver for logic cells found in the Nomadik SoC
   4 *
   5 * Copyright (C) 2008,2009 STMicroelectronics
   6 * Copyright (C) 2009 Alessandro Rubini <rubini@unipv.it>
   7 *   Rewritten based on work by Prafulla WADASKAR <prafulla.wadaskar@st.com>
   8 * Copyright (C) 2011-2013 Linus Walleij <linus.walleij@linaro.org>
   9 */
  10#include <linux/kernel.h>
  11#include <linux/init.h>
  12#include <linux/device.h>
  13#include <linux/platform_device.h>
  14#include <linux/io.h>
  15#include <linux/clk.h>
  16#include <linux/err.h>
  17#include <linux/gpio/driver.h>
  18#include <linux/spinlock.h>
  19#include <linux/interrupt.h>
  20#include <linux/slab.h>
  21#include <linux/of_device.h>
  22#include <linux/of_address.h>
  23#include <linux/bitops.h>
  24#include <linux/pinctrl/machine.h>
  25#include <linux/pinctrl/pinctrl.h>
  26#include <linux/pinctrl/pinmux.h>
  27#include <linux/pinctrl/pinconf.h>
  28/* Since we request GPIOs from ourself */
  29#include <linux/pinctrl/consumer.h>
  30#include "pinctrl-nomadik.h"
  31#include "../core.h"
  32#include "../pinctrl-utils.h"
  33
  34/*
  35 * The GPIO module in the Nomadik family of Systems-on-Chip is an
  36 * AMBA device, managing 32 pins and alternate functions.  The logic block
  37 * is currently used in the Nomadik and ux500.
  38 *
  39 * Symbols in this file are called "nmk_gpio" for "nomadik gpio"
  40 */
  41
  42/*
  43 * pin configurations are represented by 32-bit integers:
  44 *
  45 *      bit  0.. 8 - Pin Number (512 Pins Maximum)
  46 *      bit  9..10 - Alternate Function Selection
  47 *      bit 11..12 - Pull up/down state
  48 *      bit     13 - Sleep mode behaviour
  49 *      bit     14 - Direction
  50 *      bit     15 - Value (if output)
  51 *      bit 16..18 - SLPM pull up/down state
  52 *      bit 19..20 - SLPM direction
  53 *      bit 21..22 - SLPM Value (if output)
  54 *      bit 23..25 - PDIS value (if input)
  55 *      bit     26 - Gpio mode
  56 *      bit     27 - Sleep mode
  57 *
  58 * to facilitate the definition, the following macros are provided
  59 *
  60 * PIN_CFG_DEFAULT - default config (0):
  61 *                   pull up/down = disabled
  62 *                   sleep mode = input/wakeup
  63 *                   direction = input
  64 *                   value = low
  65 *                   SLPM direction = same as normal
  66 *                   SLPM pull = same as normal
  67 *                   SLPM value = same as normal
  68 *
  69 * PIN_CFG         - default config with alternate function
  70 */
  71
  72typedef unsigned long pin_cfg_t;
  73
  74#define PIN_NUM_MASK            0x1ff
  75#define PIN_NUM(x)              ((x) & PIN_NUM_MASK)
  76
  77#define PIN_ALT_SHIFT           9
  78#define PIN_ALT_MASK            (0x3 << PIN_ALT_SHIFT)
  79#define PIN_ALT(x)              (((x) & PIN_ALT_MASK) >> PIN_ALT_SHIFT)
  80#define PIN_GPIO                (NMK_GPIO_ALT_GPIO << PIN_ALT_SHIFT)
  81#define PIN_ALT_A               (NMK_GPIO_ALT_A << PIN_ALT_SHIFT)
  82#define PIN_ALT_B               (NMK_GPIO_ALT_B << PIN_ALT_SHIFT)
  83#define PIN_ALT_C               (NMK_GPIO_ALT_C << PIN_ALT_SHIFT)
  84
  85#define PIN_PULL_SHIFT          11
  86#define PIN_PULL_MASK           (0x3 << PIN_PULL_SHIFT)
  87#define PIN_PULL(x)             (((x) & PIN_PULL_MASK) >> PIN_PULL_SHIFT)
  88#define PIN_PULL_NONE           (NMK_GPIO_PULL_NONE << PIN_PULL_SHIFT)
  89#define PIN_PULL_UP             (NMK_GPIO_PULL_UP << PIN_PULL_SHIFT)
  90#define PIN_PULL_DOWN           (NMK_GPIO_PULL_DOWN << PIN_PULL_SHIFT)
  91
  92#define PIN_SLPM_SHIFT          13
  93#define PIN_SLPM_MASK           (0x1 << PIN_SLPM_SHIFT)
  94#define PIN_SLPM(x)             (((x) & PIN_SLPM_MASK) >> PIN_SLPM_SHIFT)
  95#define PIN_SLPM_MAKE_INPUT     (NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT)
  96#define PIN_SLPM_NOCHANGE       (NMK_GPIO_SLPM_NOCHANGE << PIN_SLPM_SHIFT)
  97/* These two replace the above in DB8500v2+ */
  98#define PIN_SLPM_WAKEUP_ENABLE  (NMK_GPIO_SLPM_WAKEUP_ENABLE << PIN_SLPM_SHIFT)
  99#define PIN_SLPM_WAKEUP_DISABLE (NMK_GPIO_SLPM_WAKEUP_DISABLE << PIN_SLPM_SHIFT)
 100#define PIN_SLPM_USE_MUX_SETTINGS_IN_SLEEP PIN_SLPM_WAKEUP_DISABLE
 101
 102#define PIN_SLPM_GPIO  PIN_SLPM_WAKEUP_ENABLE /* In SLPM, pin is a gpio */
 103#define PIN_SLPM_ALTFUNC PIN_SLPM_WAKEUP_DISABLE /* In SLPM, pin is altfunc */
 104
 105#define PIN_DIR_SHIFT           14
 106#define PIN_DIR_MASK            (0x1 << PIN_DIR_SHIFT)
 107#define PIN_DIR(x)              (((x) & PIN_DIR_MASK) >> PIN_DIR_SHIFT)
 108#define PIN_DIR_INPUT           (0 << PIN_DIR_SHIFT)
 109#define PIN_DIR_OUTPUT          (1 << PIN_DIR_SHIFT)
 110
 111#define PIN_VAL_SHIFT           15
 112#define PIN_VAL_MASK            (0x1 << PIN_VAL_SHIFT)
 113#define PIN_VAL(x)              (((x) & PIN_VAL_MASK) >> PIN_VAL_SHIFT)
 114#define PIN_VAL_LOW             (0 << PIN_VAL_SHIFT)
 115#define PIN_VAL_HIGH            (1 << PIN_VAL_SHIFT)
 116
 117#define PIN_SLPM_PULL_SHIFT     16
 118#define PIN_SLPM_PULL_MASK      (0x7 << PIN_SLPM_PULL_SHIFT)
 119#define PIN_SLPM_PULL(x)        \
 120        (((x) & PIN_SLPM_PULL_MASK) >> PIN_SLPM_PULL_SHIFT)
 121#define PIN_SLPM_PULL_NONE      \
 122        ((1 + NMK_GPIO_PULL_NONE) << PIN_SLPM_PULL_SHIFT)
 123#define PIN_SLPM_PULL_UP        \
 124        ((1 + NMK_GPIO_PULL_UP) << PIN_SLPM_PULL_SHIFT)
 125#define PIN_SLPM_PULL_DOWN      \
 126        ((1 + NMK_GPIO_PULL_DOWN) << PIN_SLPM_PULL_SHIFT)
 127
 128#define PIN_SLPM_DIR_SHIFT      19
 129#define PIN_SLPM_DIR_MASK       (0x3 << PIN_SLPM_DIR_SHIFT)
 130#define PIN_SLPM_DIR(x)         \
 131        (((x) & PIN_SLPM_DIR_MASK) >> PIN_SLPM_DIR_SHIFT)
 132#define PIN_SLPM_DIR_INPUT      ((1 + 0) << PIN_SLPM_DIR_SHIFT)
 133#define PIN_SLPM_DIR_OUTPUT     ((1 + 1) << PIN_SLPM_DIR_SHIFT)
 134
 135#define PIN_SLPM_VAL_SHIFT      21
 136#define PIN_SLPM_VAL_MASK       (0x3 << PIN_SLPM_VAL_SHIFT)
 137#define PIN_SLPM_VAL(x)         \
 138        (((x) & PIN_SLPM_VAL_MASK) >> PIN_SLPM_VAL_SHIFT)
 139#define PIN_SLPM_VAL_LOW        ((1 + 0) << PIN_SLPM_VAL_SHIFT)
 140#define PIN_SLPM_VAL_HIGH       ((1 + 1) << PIN_SLPM_VAL_SHIFT)
 141
 142#define PIN_SLPM_PDIS_SHIFT             23
 143#define PIN_SLPM_PDIS_MASK              (0x3 << PIN_SLPM_PDIS_SHIFT)
 144#define PIN_SLPM_PDIS(x)        \
 145        (((x) & PIN_SLPM_PDIS_MASK) >> PIN_SLPM_PDIS_SHIFT)
 146#define PIN_SLPM_PDIS_NO_CHANGE         (0 << PIN_SLPM_PDIS_SHIFT)
 147#define PIN_SLPM_PDIS_DISABLED          (1 << PIN_SLPM_PDIS_SHIFT)
 148#define PIN_SLPM_PDIS_ENABLED           (2 << PIN_SLPM_PDIS_SHIFT)
 149
 150#define PIN_LOWEMI_SHIFT        25
 151#define PIN_LOWEMI_MASK         (0x1 << PIN_LOWEMI_SHIFT)
 152#define PIN_LOWEMI(x)           (((x) & PIN_LOWEMI_MASK) >> PIN_LOWEMI_SHIFT)
 153#define PIN_LOWEMI_DISABLED     (0 << PIN_LOWEMI_SHIFT)
 154#define PIN_LOWEMI_ENABLED      (1 << PIN_LOWEMI_SHIFT)
 155
 156#define PIN_GPIOMODE_SHIFT      26
 157#define PIN_GPIOMODE_MASK       (0x1 << PIN_GPIOMODE_SHIFT)
 158#define PIN_GPIOMODE(x)         (((x) & PIN_GPIOMODE_MASK) >> PIN_GPIOMODE_SHIFT)
 159#define PIN_GPIOMODE_DISABLED   (0 << PIN_GPIOMODE_SHIFT)
 160#define PIN_GPIOMODE_ENABLED    (1 << PIN_GPIOMODE_SHIFT)
 161
 162#define PIN_SLEEPMODE_SHIFT     27
 163#define PIN_SLEEPMODE_MASK      (0x1 << PIN_SLEEPMODE_SHIFT)
 164#define PIN_SLEEPMODE(x)        (((x) & PIN_SLEEPMODE_MASK) >> PIN_SLEEPMODE_SHIFT)
 165#define PIN_SLEEPMODE_DISABLED  (0 << PIN_SLEEPMODE_SHIFT)
 166#define PIN_SLEEPMODE_ENABLED   (1 << PIN_SLEEPMODE_SHIFT)
 167
 168
 169/* Shortcuts.  Use these instead of separate DIR, PULL, and VAL.  */
 170#define PIN_INPUT_PULLDOWN      (PIN_DIR_INPUT | PIN_PULL_DOWN)
 171#define PIN_INPUT_PULLUP        (PIN_DIR_INPUT | PIN_PULL_UP)
 172#define PIN_INPUT_NOPULL        (PIN_DIR_INPUT | PIN_PULL_NONE)
 173#define PIN_OUTPUT_LOW          (PIN_DIR_OUTPUT | PIN_VAL_LOW)
 174#define PIN_OUTPUT_HIGH         (PIN_DIR_OUTPUT | PIN_VAL_HIGH)
 175
 176#define PIN_SLPM_INPUT_PULLDOWN (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_DOWN)
 177#define PIN_SLPM_INPUT_PULLUP   (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_UP)
 178#define PIN_SLPM_INPUT_NOPULL   (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_NONE)
 179#define PIN_SLPM_OUTPUT_LOW     (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_LOW)
 180#define PIN_SLPM_OUTPUT_HIGH    (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_HIGH)
 181
 182#define PIN_CFG_DEFAULT         (0)
 183
 184#define PIN_CFG(num, alt)               \
 185        (PIN_CFG_DEFAULT |\
 186         (PIN_NUM(num) | PIN_##alt))
 187
 188#define PIN_CFG_INPUT(num, alt, pull)           \
 189        (PIN_CFG_DEFAULT |\
 190         (PIN_NUM(num) | PIN_##alt | PIN_INPUT_##pull))
 191
 192#define PIN_CFG_OUTPUT(num, alt, val)           \
 193        (PIN_CFG_DEFAULT |\
 194         (PIN_NUM(num) | PIN_##alt | PIN_OUTPUT_##val))
 195
 196/*
 197 * "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving
 198 * the "gpio" namespace for generic and cross-machine functions
 199 */
 200
 201#define GPIO_BLOCK_SHIFT 5
 202#define NMK_GPIO_PER_CHIP (1 << GPIO_BLOCK_SHIFT)
 203#define NMK_MAX_BANKS DIV_ROUND_UP(512, NMK_GPIO_PER_CHIP)
 204
 205/* Register in the logic block */
 206#define NMK_GPIO_DAT    0x00
 207#define NMK_GPIO_DATS   0x04
 208#define NMK_GPIO_DATC   0x08
 209#define NMK_GPIO_PDIS   0x0c
 210#define NMK_GPIO_DIR    0x10
 211#define NMK_GPIO_DIRS   0x14
 212#define NMK_GPIO_DIRC   0x18
 213#define NMK_GPIO_SLPC   0x1c
 214#define NMK_GPIO_AFSLA  0x20
 215#define NMK_GPIO_AFSLB  0x24
 216#define NMK_GPIO_LOWEMI 0x28
 217
 218#define NMK_GPIO_RIMSC  0x40
 219#define NMK_GPIO_FIMSC  0x44
 220#define NMK_GPIO_IS     0x48
 221#define NMK_GPIO_IC     0x4c
 222#define NMK_GPIO_RWIMSC 0x50
 223#define NMK_GPIO_FWIMSC 0x54
 224#define NMK_GPIO_WKS    0x58
 225/* These appear in DB8540 and later ASICs */
 226#define NMK_GPIO_EDGELEVEL 0x5C
 227#define NMK_GPIO_LEVEL  0x60
 228
 229
 230/* Pull up/down values */
 231enum nmk_gpio_pull {
 232        NMK_GPIO_PULL_NONE,
 233        NMK_GPIO_PULL_UP,
 234        NMK_GPIO_PULL_DOWN,
 235};
 236
 237/* Sleep mode */
 238enum nmk_gpio_slpm {
 239        NMK_GPIO_SLPM_INPUT,
 240        NMK_GPIO_SLPM_WAKEUP_ENABLE = NMK_GPIO_SLPM_INPUT,
 241        NMK_GPIO_SLPM_NOCHANGE,
 242        NMK_GPIO_SLPM_WAKEUP_DISABLE = NMK_GPIO_SLPM_NOCHANGE,
 243};
 244
 245struct nmk_gpio_chip {
 246        struct gpio_chip chip;
 247        struct irq_chip irqchip;
 248        void __iomem *addr;
 249        struct clk *clk;
 250        unsigned int bank;
 251        void (*set_ioforce)(bool enable);
 252        spinlock_t lock;
 253        bool sleepmode;
 254        /* Keep track of configured edges */
 255        u32 edge_rising;
 256        u32 edge_falling;
 257        u32 real_wake;
 258        u32 rwimsc;
 259        u32 fwimsc;
 260        u32 rimsc;
 261        u32 fimsc;
 262        u32 pull_up;
 263        u32 lowemi;
 264};
 265
 266/**
 267 * struct nmk_pinctrl - state container for the Nomadik pin controller
 268 * @dev: containing device pointer
 269 * @pctl: corresponding pin controller device
 270 * @soc: SoC data for this specific chip
 271 * @prcm_base: PRCM register range virtual base
 272 */
 273struct nmk_pinctrl {
 274        struct device *dev;
 275        struct pinctrl_dev *pctl;
 276        const struct nmk_pinctrl_soc_data *soc;
 277        void __iomem *prcm_base;
 278};
 279
 280static struct nmk_gpio_chip *nmk_gpio_chips[NMK_MAX_BANKS];
 281
 282static DEFINE_SPINLOCK(nmk_gpio_slpm_lock);
 283
 284#define NUM_BANKS ARRAY_SIZE(nmk_gpio_chips)
 285
 286static void __nmk_gpio_set_mode(struct nmk_gpio_chip *nmk_chip,
 287                                unsigned offset, int gpio_mode)
 288{
 289        u32 afunc, bfunc;
 290
 291        afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & ~BIT(offset);
 292        bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & ~BIT(offset);
 293        if (gpio_mode & NMK_GPIO_ALT_A)
 294                afunc |= BIT(offset);
 295        if (gpio_mode & NMK_GPIO_ALT_B)
 296                bfunc |= BIT(offset);
 297        writel(afunc, nmk_chip->addr + NMK_GPIO_AFSLA);
 298        writel(bfunc, nmk_chip->addr + NMK_GPIO_AFSLB);
 299}
 300
 301static void __nmk_gpio_set_slpm(struct nmk_gpio_chip *nmk_chip,
 302                                unsigned offset, enum nmk_gpio_slpm mode)
 303{
 304        u32 slpm;
 305
 306        slpm = readl(nmk_chip->addr + NMK_GPIO_SLPC);
 307        if (mode == NMK_GPIO_SLPM_NOCHANGE)
 308                slpm |= BIT(offset);
 309        else
 310                slpm &= ~BIT(offset);
 311        writel(slpm, nmk_chip->addr + NMK_GPIO_SLPC);
 312}
 313
 314static void __nmk_gpio_set_pull(struct nmk_gpio_chip *nmk_chip,
 315                                unsigned offset, enum nmk_gpio_pull pull)
 316{
 317        u32 pdis;
 318
 319        pdis = readl(nmk_chip->addr + NMK_GPIO_PDIS);
 320        if (pull == NMK_GPIO_PULL_NONE) {
 321                pdis |= BIT(offset);
 322                nmk_chip->pull_up &= ~BIT(offset);
 323        } else {
 324                pdis &= ~BIT(offset);
 325        }
 326
 327        writel(pdis, nmk_chip->addr + NMK_GPIO_PDIS);
 328
 329        if (pull == NMK_GPIO_PULL_UP) {
 330                nmk_chip->pull_up |= BIT(offset);
 331                writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATS);
 332        } else if (pull == NMK_GPIO_PULL_DOWN) {
 333                nmk_chip->pull_up &= ~BIT(offset);
 334                writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATC);
 335        }
 336}
 337
 338static void __nmk_gpio_set_lowemi(struct nmk_gpio_chip *nmk_chip,
 339                                  unsigned offset, bool lowemi)
 340{
 341        bool enabled = nmk_chip->lowemi & BIT(offset);
 342
 343        if (lowemi == enabled)
 344                return;
 345
 346        if (lowemi)
 347                nmk_chip->lowemi |= BIT(offset);
 348        else
 349                nmk_chip->lowemi &= ~BIT(offset);
 350
 351        writel_relaxed(nmk_chip->lowemi,
 352                       nmk_chip->addr + NMK_GPIO_LOWEMI);
 353}
 354
 355static void __nmk_gpio_make_input(struct nmk_gpio_chip *nmk_chip,
 356                                  unsigned offset)
 357{
 358        writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DIRC);
 359}
 360
 361static void __nmk_gpio_set_output(struct nmk_gpio_chip *nmk_chip,
 362                                  unsigned offset, int val)
 363{
 364        if (val)
 365                writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATS);
 366        else
 367                writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATC);
 368}
 369
 370static void __nmk_gpio_make_output(struct nmk_gpio_chip *nmk_chip,
 371                                  unsigned offset, int val)
 372{
 373        writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DIRS);
 374        __nmk_gpio_set_output(nmk_chip, offset, val);
 375}
 376
 377static void __nmk_gpio_set_mode_safe(struct nmk_gpio_chip *nmk_chip,
 378                                     unsigned offset, int gpio_mode,
 379                                     bool glitch)
 380{
 381        u32 rwimsc = nmk_chip->rwimsc;
 382        u32 fwimsc = nmk_chip->fwimsc;
 383
 384        if (glitch && nmk_chip->set_ioforce) {
 385                u32 bit = BIT(offset);
 386
 387                /* Prevent spurious wakeups */
 388                writel(rwimsc & ~bit, nmk_chip->addr + NMK_GPIO_RWIMSC);
 389                writel(fwimsc & ~bit, nmk_chip->addr + NMK_GPIO_FWIMSC);
 390
 391                nmk_chip->set_ioforce(true);
 392        }
 393
 394        __nmk_gpio_set_mode(nmk_chip, offset, gpio_mode);
 395
 396        if (glitch && nmk_chip->set_ioforce) {
 397                nmk_chip->set_ioforce(false);
 398
 399                writel(rwimsc, nmk_chip->addr + NMK_GPIO_RWIMSC);
 400                writel(fwimsc, nmk_chip->addr + NMK_GPIO_FWIMSC);
 401        }
 402}
 403
 404static void
 405nmk_gpio_disable_lazy_irq(struct nmk_gpio_chip *nmk_chip, unsigned offset)
 406{
 407        u32 falling = nmk_chip->fimsc & BIT(offset);
 408        u32 rising = nmk_chip->rimsc & BIT(offset);
 409        int gpio = nmk_chip->chip.base + offset;
 410        int irq = irq_find_mapping(nmk_chip->chip.irq.domain, offset);
 411        struct irq_data *d = irq_get_irq_data(irq);
 412
 413        if (!rising && !falling)
 414                return;
 415
 416        if (!d || !irqd_irq_disabled(d))
 417                return;
 418
 419        if (rising) {
 420                nmk_chip->rimsc &= ~BIT(offset);
 421                writel_relaxed(nmk_chip->rimsc,
 422                               nmk_chip->addr + NMK_GPIO_RIMSC);
 423        }
 424
 425        if (falling) {
 426                nmk_chip->fimsc &= ~BIT(offset);
 427                writel_relaxed(nmk_chip->fimsc,
 428                               nmk_chip->addr + NMK_GPIO_FIMSC);
 429        }
 430
 431        dev_dbg(nmk_chip->chip.parent, "%d: clearing interrupt mask\n", gpio);
 432}
 433
 434static void nmk_write_masked(void __iomem *reg, u32 mask, u32 value)
 435{
 436        u32 val;
 437
 438        val = readl(reg);
 439        val = ((val & ~mask) | (value & mask));
 440        writel(val, reg);
 441}
 442
 443static void nmk_prcm_altcx_set_mode(struct nmk_pinctrl *npct,
 444        unsigned offset, unsigned alt_num)
 445{
 446        int i;
 447        u16 reg;
 448        u8 bit;
 449        u8 alt_index;
 450        const struct prcm_gpiocr_altcx_pin_desc *pin_desc;
 451        const u16 *gpiocr_regs;
 452
 453        if (!npct->prcm_base)
 454                return;
 455
 456        if (alt_num > PRCM_IDX_GPIOCR_ALTC_MAX) {
 457                dev_err(npct->dev, "PRCM GPIOCR: alternate-C%i is invalid\n",
 458                        alt_num);
 459                return;
 460        }
 461
 462        for (i = 0 ; i < npct->soc->npins_altcx ; i++) {
 463                if (npct->soc->altcx_pins[i].pin == offset)
 464                        break;
 465        }
 466        if (i == npct->soc->npins_altcx) {
 467                dev_dbg(npct->dev, "PRCM GPIOCR: pin %i is not found\n",
 468                        offset);
 469                return;
 470        }
 471
 472        pin_desc = npct->soc->altcx_pins + i;
 473        gpiocr_regs = npct->soc->prcm_gpiocr_registers;
 474
 475        /*
 476         * If alt_num is NULL, just clear current ALTCx selection
 477         * to make sure we come back to a pure ALTC selection
 478         */
 479        if (!alt_num) {
 480                for (i = 0 ; i < PRCM_IDX_GPIOCR_ALTC_MAX ; i++) {
 481                        if (pin_desc->altcx[i].used == true) {
 482                                reg = gpiocr_regs[pin_desc->altcx[i].reg_index];
 483                                bit = pin_desc->altcx[i].control_bit;
 484                                if (readl(npct->prcm_base + reg) & BIT(bit)) {
 485                                        nmk_write_masked(npct->prcm_base + reg, BIT(bit), 0);
 486                                        dev_dbg(npct->dev,
 487                                                "PRCM GPIOCR: pin %i: alternate-C%i has been disabled\n",
 488                                                offset, i+1);
 489                                }
 490                        }
 491                }
 492                return;
 493        }
 494
 495        alt_index = alt_num - 1;
 496        if (pin_desc->altcx[alt_index].used == false) {
 497                dev_warn(npct->dev,
 498                        "PRCM GPIOCR: pin %i: alternate-C%i does not exist\n",
 499                        offset, alt_num);
 500                return;
 501        }
 502
 503        /*
 504         * Check if any other ALTCx functions are activated on this pin
 505         * and disable it first.
 506         */
 507        for (i = 0 ; i < PRCM_IDX_GPIOCR_ALTC_MAX ; i++) {
 508                if (i == alt_index)
 509                        continue;
 510                if (pin_desc->altcx[i].used == true) {
 511                        reg = gpiocr_regs[pin_desc->altcx[i].reg_index];
 512                        bit = pin_desc->altcx[i].control_bit;
 513                        if (readl(npct->prcm_base + reg) & BIT(bit)) {
 514                                nmk_write_masked(npct->prcm_base + reg, BIT(bit), 0);
 515                                dev_dbg(npct->dev,
 516                                        "PRCM GPIOCR: pin %i: alternate-C%i has been disabled\n",
 517                                        offset, i+1);
 518                        }
 519                }
 520        }
 521
 522        reg = gpiocr_regs[pin_desc->altcx[alt_index].reg_index];
 523        bit = pin_desc->altcx[alt_index].control_bit;
 524        dev_dbg(npct->dev, "PRCM GPIOCR: pin %i: alternate-C%i has been selected\n",
 525                offset, alt_index+1);
 526        nmk_write_masked(npct->prcm_base + reg, BIT(bit), BIT(bit));
 527}
 528
 529/*
 530 * Safe sequence used to switch IOs between GPIO and Alternate-C mode:
 531 *  - Save SLPM registers
 532 *  - Set SLPM=0 for the IOs you want to switch and others to 1
 533 *  - Configure the GPIO registers for the IOs that are being switched
 534 *  - Set IOFORCE=1
 535 *  - Modify the AFLSA/B registers for the IOs that are being switched
 536 *  - Set IOFORCE=0
 537 *  - Restore SLPM registers
 538 *  - Any spurious wake up event during switch sequence to be ignored and
 539 *    cleared
 540 */
 541static void nmk_gpio_glitch_slpm_init(unsigned int *slpm)
 542{
 543        int i;
 544
 545        for (i = 0; i < NUM_BANKS; i++) {
 546                struct nmk_gpio_chip *chip = nmk_gpio_chips[i];
 547                unsigned int temp = slpm[i];
 548
 549                if (!chip)
 550                        break;
 551
 552                clk_enable(chip->clk);
 553
 554                slpm[i] = readl(chip->addr + NMK_GPIO_SLPC);
 555                writel(temp, chip->addr + NMK_GPIO_SLPC);
 556        }
 557}
 558
 559static void nmk_gpio_glitch_slpm_restore(unsigned int *slpm)
 560{
 561        int i;
 562
 563        for (i = 0; i < NUM_BANKS; i++) {
 564                struct nmk_gpio_chip *chip = nmk_gpio_chips[i];
 565
 566                if (!chip)
 567                        break;
 568
 569                writel(slpm[i], chip->addr + NMK_GPIO_SLPC);
 570
 571                clk_disable(chip->clk);
 572        }
 573}
 574
 575static int __maybe_unused nmk_prcm_gpiocr_get_mode(struct pinctrl_dev *pctldev, int gpio)
 576{
 577        int i;
 578        u16 reg;
 579        u8 bit;
 580        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
 581        const struct prcm_gpiocr_altcx_pin_desc *pin_desc;
 582        const u16 *gpiocr_regs;
 583
 584        if (!npct->prcm_base)
 585                return NMK_GPIO_ALT_C;
 586
 587        for (i = 0; i < npct->soc->npins_altcx; i++) {
 588                if (npct->soc->altcx_pins[i].pin == gpio)
 589                        break;
 590        }
 591        if (i == npct->soc->npins_altcx)
 592                return NMK_GPIO_ALT_C;
 593
 594        pin_desc = npct->soc->altcx_pins + i;
 595        gpiocr_regs = npct->soc->prcm_gpiocr_registers;
 596        for (i = 0; i < PRCM_IDX_GPIOCR_ALTC_MAX; i++) {
 597                if (pin_desc->altcx[i].used == true) {
 598                        reg = gpiocr_regs[pin_desc->altcx[i].reg_index];
 599                        bit = pin_desc->altcx[i].control_bit;
 600                        if (readl(npct->prcm_base + reg) & BIT(bit))
 601                                return NMK_GPIO_ALT_C+i+1;
 602                }
 603        }
 604        return NMK_GPIO_ALT_C;
 605}
 606
 607/* IRQ functions */
 608
 609static void nmk_gpio_irq_ack(struct irq_data *d)
 610{
 611        struct gpio_chip *chip = irq_data_get_irq_chip_data(d);
 612        struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip);
 613
 614        clk_enable(nmk_chip->clk);
 615        writel(BIT(d->hwirq), nmk_chip->addr + NMK_GPIO_IC);
 616        clk_disable(nmk_chip->clk);
 617}
 618
 619enum nmk_gpio_irq_type {
 620        NORMAL,
 621        WAKE,
 622};
 623
 624static void __nmk_gpio_irq_modify(struct nmk_gpio_chip *nmk_chip,
 625                                  int offset, enum nmk_gpio_irq_type which,
 626                                  bool enable)
 627{
 628        u32 *rimscval;
 629        u32 *fimscval;
 630        u32 rimscreg;
 631        u32 fimscreg;
 632
 633        if (which == NORMAL) {
 634                rimscreg = NMK_GPIO_RIMSC;
 635                fimscreg = NMK_GPIO_FIMSC;
 636                rimscval = &nmk_chip->rimsc;
 637                fimscval = &nmk_chip->fimsc;
 638        } else  {
 639                rimscreg = NMK_GPIO_RWIMSC;
 640                fimscreg = NMK_GPIO_FWIMSC;
 641                rimscval = &nmk_chip->rwimsc;
 642                fimscval = &nmk_chip->fwimsc;
 643        }
 644
 645        /* we must individually set/clear the two edges */
 646        if (nmk_chip->edge_rising & BIT(offset)) {
 647                if (enable)
 648                        *rimscval |= BIT(offset);
 649                else
 650                        *rimscval &= ~BIT(offset);
 651                writel(*rimscval, nmk_chip->addr + rimscreg);
 652        }
 653        if (nmk_chip->edge_falling & BIT(offset)) {
 654                if (enable)
 655                        *fimscval |= BIT(offset);
 656                else
 657                        *fimscval &= ~BIT(offset);
 658                writel(*fimscval, nmk_chip->addr + fimscreg);
 659        }
 660}
 661
 662static void __nmk_gpio_set_wake(struct nmk_gpio_chip *nmk_chip,
 663                                int offset, bool on)
 664{
 665        /*
 666         * Ensure WAKEUP_ENABLE is on.  No need to disable it if wakeup is
 667         * disabled, since setting SLPM to 1 increases power consumption, and
 668         * wakeup is anyhow controlled by the RIMSC and FIMSC registers.
 669         */
 670        if (nmk_chip->sleepmode && on) {
 671                __nmk_gpio_set_slpm(nmk_chip, offset,
 672                                    NMK_GPIO_SLPM_WAKEUP_ENABLE);
 673        }
 674
 675        __nmk_gpio_irq_modify(nmk_chip, offset, WAKE, on);
 676}
 677
 678static int nmk_gpio_irq_maskunmask(struct irq_data *d, bool enable)
 679{
 680        struct nmk_gpio_chip *nmk_chip;
 681        unsigned long flags;
 682
 683        nmk_chip = irq_data_get_irq_chip_data(d);
 684        if (!nmk_chip)
 685                return -EINVAL;
 686
 687        clk_enable(nmk_chip->clk);
 688        spin_lock_irqsave(&nmk_gpio_slpm_lock, flags);
 689        spin_lock(&nmk_chip->lock);
 690
 691        __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, enable);
 692
 693        if (!(nmk_chip->real_wake & BIT(d->hwirq)))
 694                __nmk_gpio_set_wake(nmk_chip, d->hwirq, enable);
 695
 696        spin_unlock(&nmk_chip->lock);
 697        spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags);
 698        clk_disable(nmk_chip->clk);
 699
 700        return 0;
 701}
 702
 703static void nmk_gpio_irq_mask(struct irq_data *d)
 704{
 705        nmk_gpio_irq_maskunmask(d, false);
 706}
 707
 708static void nmk_gpio_irq_unmask(struct irq_data *d)
 709{
 710        nmk_gpio_irq_maskunmask(d, true);
 711}
 712
 713static int nmk_gpio_irq_set_wake(struct irq_data *d, unsigned int on)
 714{
 715        struct nmk_gpio_chip *nmk_chip;
 716        unsigned long flags;
 717
 718        nmk_chip = irq_data_get_irq_chip_data(d);
 719        if (!nmk_chip)
 720                return -EINVAL;
 721
 722        clk_enable(nmk_chip->clk);
 723        spin_lock_irqsave(&nmk_gpio_slpm_lock, flags);
 724        spin_lock(&nmk_chip->lock);
 725
 726        if (irqd_irq_disabled(d))
 727                __nmk_gpio_set_wake(nmk_chip, d->hwirq, on);
 728
 729        if (on)
 730                nmk_chip->real_wake |= BIT(d->hwirq);
 731        else
 732                nmk_chip->real_wake &= ~BIT(d->hwirq);
 733
 734        spin_unlock(&nmk_chip->lock);
 735        spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags);
 736        clk_disable(nmk_chip->clk);
 737
 738        return 0;
 739}
 740
 741static int nmk_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 742{
 743        bool enabled = !irqd_irq_disabled(d);
 744        bool wake = irqd_is_wakeup_set(d);
 745        struct nmk_gpio_chip *nmk_chip;
 746        unsigned long flags;
 747
 748        nmk_chip = irq_data_get_irq_chip_data(d);
 749        if (!nmk_chip)
 750                return -EINVAL;
 751        if (type & IRQ_TYPE_LEVEL_HIGH)
 752                return -EINVAL;
 753        if (type & IRQ_TYPE_LEVEL_LOW)
 754                return -EINVAL;
 755
 756        clk_enable(nmk_chip->clk);
 757        spin_lock_irqsave(&nmk_chip->lock, flags);
 758
 759        if (enabled)
 760                __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, false);
 761
 762        if (enabled || wake)
 763                __nmk_gpio_irq_modify(nmk_chip, d->hwirq, WAKE, false);
 764
 765        nmk_chip->edge_rising &= ~BIT(d->hwirq);
 766        if (type & IRQ_TYPE_EDGE_RISING)
 767                nmk_chip->edge_rising |= BIT(d->hwirq);
 768
 769        nmk_chip->edge_falling &= ~BIT(d->hwirq);
 770        if (type & IRQ_TYPE_EDGE_FALLING)
 771                nmk_chip->edge_falling |= BIT(d->hwirq);
 772
 773        if (enabled)
 774                __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, true);
 775
 776        if (enabled || wake)
 777                __nmk_gpio_irq_modify(nmk_chip, d->hwirq, WAKE, true);
 778
 779        spin_unlock_irqrestore(&nmk_chip->lock, flags);
 780        clk_disable(nmk_chip->clk);
 781
 782        return 0;
 783}
 784
 785static unsigned int nmk_gpio_irq_startup(struct irq_data *d)
 786{
 787        struct nmk_gpio_chip *nmk_chip = irq_data_get_irq_chip_data(d);
 788
 789        clk_enable(nmk_chip->clk);
 790        nmk_gpio_irq_unmask(d);
 791        return 0;
 792}
 793
 794static void nmk_gpio_irq_shutdown(struct irq_data *d)
 795{
 796        struct nmk_gpio_chip *nmk_chip = irq_data_get_irq_chip_data(d);
 797
 798        nmk_gpio_irq_mask(d);
 799        clk_disable(nmk_chip->clk);
 800}
 801
 802static void nmk_gpio_irq_handler(struct irq_desc *desc)
 803{
 804        struct irq_chip *host_chip = irq_desc_get_chip(desc);
 805        struct gpio_chip *chip = irq_desc_get_handler_data(desc);
 806        struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip);
 807        u32 status;
 808
 809        chained_irq_enter(host_chip, desc);
 810
 811        clk_enable(nmk_chip->clk);
 812        status = readl(nmk_chip->addr + NMK_GPIO_IS);
 813        clk_disable(nmk_chip->clk);
 814
 815        while (status) {
 816                int bit = __ffs(status);
 817
 818                generic_handle_domain_irq(chip->irq.domain, bit);
 819                status &= ~BIT(bit);
 820        }
 821
 822        chained_irq_exit(host_chip, desc);
 823}
 824
 825/* I/O Functions */
 826
 827static int nmk_gpio_get_dir(struct gpio_chip *chip, unsigned offset)
 828{
 829        struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip);
 830        int dir;
 831
 832        clk_enable(nmk_chip->clk);
 833
 834        dir = readl(nmk_chip->addr + NMK_GPIO_DIR) & BIT(offset);
 835
 836        clk_disable(nmk_chip->clk);
 837
 838        if (dir)
 839                return GPIO_LINE_DIRECTION_OUT;
 840
 841        return GPIO_LINE_DIRECTION_IN;
 842}
 843
 844static int nmk_gpio_make_input(struct gpio_chip *chip, unsigned offset)
 845{
 846        struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip);
 847
 848        clk_enable(nmk_chip->clk);
 849
 850        writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DIRC);
 851
 852        clk_disable(nmk_chip->clk);
 853
 854        return 0;
 855}
 856
 857static int nmk_gpio_get_input(struct gpio_chip *chip, unsigned offset)
 858{
 859        struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip);
 860        int value;
 861
 862        clk_enable(nmk_chip->clk);
 863
 864        value = !!(readl(nmk_chip->addr + NMK_GPIO_DAT) & BIT(offset));
 865
 866        clk_disable(nmk_chip->clk);
 867
 868        return value;
 869}
 870
 871static void nmk_gpio_set_output(struct gpio_chip *chip, unsigned offset,
 872                                int val)
 873{
 874        struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip);
 875
 876        clk_enable(nmk_chip->clk);
 877
 878        __nmk_gpio_set_output(nmk_chip, offset, val);
 879
 880        clk_disable(nmk_chip->clk);
 881}
 882
 883static int nmk_gpio_make_output(struct gpio_chip *chip, unsigned offset,
 884                                int val)
 885{
 886        struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip);
 887
 888        clk_enable(nmk_chip->clk);
 889
 890        __nmk_gpio_make_output(nmk_chip, offset, val);
 891
 892        clk_disable(nmk_chip->clk);
 893
 894        return 0;
 895}
 896
 897#ifdef CONFIG_DEBUG_FS
 898static int nmk_gpio_get_mode(struct nmk_gpio_chip *nmk_chip, int offset)
 899{
 900        u32 afunc, bfunc;
 901
 902        clk_enable(nmk_chip->clk);
 903
 904        afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & BIT(offset);
 905        bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & BIT(offset);
 906
 907        clk_disable(nmk_chip->clk);
 908
 909        return (afunc ? NMK_GPIO_ALT_A : 0) | (bfunc ? NMK_GPIO_ALT_B : 0);
 910}
 911
 912#include <linux/seq_file.h>
 913
 914static void nmk_gpio_dbg_show_one(struct seq_file *s,
 915        struct pinctrl_dev *pctldev, struct gpio_chip *chip,
 916        unsigned offset, unsigned gpio)
 917{
 918        const char *label = gpiochip_is_requested(chip, offset);
 919        struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip);
 920        int mode;
 921        bool is_out;
 922        bool data_out;
 923        bool pull;
 924        const char *modes[] = {
 925                [NMK_GPIO_ALT_GPIO]     = "gpio",
 926                [NMK_GPIO_ALT_A]        = "altA",
 927                [NMK_GPIO_ALT_B]        = "altB",
 928                [NMK_GPIO_ALT_C]        = "altC",
 929                [NMK_GPIO_ALT_C+1]      = "altC1",
 930                [NMK_GPIO_ALT_C+2]      = "altC2",
 931                [NMK_GPIO_ALT_C+3]      = "altC3",
 932                [NMK_GPIO_ALT_C+4]      = "altC4",
 933        };
 934
 935        clk_enable(nmk_chip->clk);
 936        is_out = !!(readl(nmk_chip->addr + NMK_GPIO_DIR) & BIT(offset));
 937        pull = !(readl(nmk_chip->addr + NMK_GPIO_PDIS) & BIT(offset));
 938        data_out = !!(readl(nmk_chip->addr + NMK_GPIO_DAT) & BIT(offset));
 939        mode = nmk_gpio_get_mode(nmk_chip, offset);
 940        if ((mode == NMK_GPIO_ALT_C) && pctldev)
 941                mode = nmk_prcm_gpiocr_get_mode(pctldev, gpio);
 942
 943        if (is_out) {
 944                seq_printf(s, " gpio-%-3d (%-20.20s) out %s           %s",
 945                           gpio,
 946                           label ?: "(none)",
 947                           data_out ? "hi" : "lo",
 948                           (mode < 0) ? "unknown" : modes[mode]);
 949        } else {
 950                int irq = chip->to_irq(chip, offset);
 951                const int pullidx = pull ? 1 : 0;
 952                int val;
 953                static const char * const pulls[] = {
 954                        "none        ",
 955                        "pull enabled",
 956                };
 957
 958                seq_printf(s, " gpio-%-3d (%-20.20s) in  %s %s",
 959                           gpio,
 960                           label ?: "(none)",
 961                           pulls[pullidx],
 962                           (mode < 0) ? "unknown" : modes[mode]);
 963
 964                val = nmk_gpio_get_input(chip, offset);
 965                seq_printf(s, " VAL %d", val);
 966
 967                /*
 968                 * This races with request_irq(), set_irq_type(),
 969                 * and set_irq_wake() ... but those are "rare".
 970                 */
 971                if (irq > 0 && irq_has_action(irq)) {
 972                        char *trigger;
 973                        bool wake;
 974
 975                        if (nmk_chip->edge_rising & BIT(offset))
 976                                trigger = "edge-rising";
 977                        else if (nmk_chip->edge_falling & BIT(offset))
 978                                trigger = "edge-falling";
 979                        else
 980                                trigger = "edge-undefined";
 981
 982                        wake = !!(nmk_chip->real_wake & BIT(offset));
 983
 984                        seq_printf(s, " irq-%d %s%s",
 985                                   irq, trigger, wake ? " wakeup" : "");
 986                }
 987        }
 988        clk_disable(nmk_chip->clk);
 989}
 990
 991static void nmk_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
 992{
 993        unsigned                i;
 994        unsigned                gpio = chip->base;
 995
 996        for (i = 0; i < chip->ngpio; i++, gpio++) {
 997                nmk_gpio_dbg_show_one(s, NULL, chip, i, gpio);
 998                seq_printf(s, "\n");
 999        }
1000}
1001
1002#else
1003static inline void nmk_gpio_dbg_show_one(struct seq_file *s,
1004                                         struct pinctrl_dev *pctldev,
1005                                         struct gpio_chip *chip,
1006                                         unsigned offset, unsigned gpio)
1007{
1008}
1009#define nmk_gpio_dbg_show       NULL
1010#endif
1011
1012/*
1013 * We will allocate memory for the state container using devm* allocators
1014 * binding to the first device reaching this point, it doesn't matter if
1015 * it is the pin controller or GPIO driver. However we need to use the right
1016 * platform device when looking up resources so pay attention to pdev.
1017 */
1018static struct nmk_gpio_chip *nmk_gpio_populate_chip(struct device_node *np,
1019                                                struct platform_device *pdev)
1020{
1021        struct nmk_gpio_chip *nmk_chip;
1022        struct platform_device *gpio_pdev;
1023        struct gpio_chip *chip;
1024        struct resource *res;
1025        struct clk *clk;
1026        void __iomem *base;
1027        u32 id;
1028
1029        gpio_pdev = of_find_device_by_node(np);
1030        if (!gpio_pdev) {
1031                pr_err("populate \"%pOFn\": device not found\n", np);
1032                return ERR_PTR(-ENODEV);
1033        }
1034        if (of_property_read_u32(np, "gpio-bank", &id)) {
1035                dev_err(&pdev->dev, "populate: gpio-bank property not found\n");
1036                platform_device_put(gpio_pdev);
1037                return ERR_PTR(-EINVAL);
1038        }
1039
1040        /* Already populated? */
1041        nmk_chip = nmk_gpio_chips[id];
1042        if (nmk_chip) {
1043                platform_device_put(gpio_pdev);
1044                return nmk_chip;
1045        }
1046
1047        nmk_chip = devm_kzalloc(&pdev->dev, sizeof(*nmk_chip), GFP_KERNEL);
1048        if (!nmk_chip) {
1049                platform_device_put(gpio_pdev);
1050                return ERR_PTR(-ENOMEM);
1051        }
1052
1053        nmk_chip->bank = id;
1054        chip = &nmk_chip->chip;
1055        chip->base = id * NMK_GPIO_PER_CHIP;
1056        chip->ngpio = NMK_GPIO_PER_CHIP;
1057        chip->label = dev_name(&gpio_pdev->dev);
1058        chip->parent = &gpio_pdev->dev;
1059
1060        res = platform_get_resource(gpio_pdev, IORESOURCE_MEM, 0);
1061        base = devm_ioremap_resource(&pdev->dev, res);
1062        if (IS_ERR(base)) {
1063                platform_device_put(gpio_pdev);
1064                return ERR_CAST(base);
1065        }
1066        nmk_chip->addr = base;
1067
1068        clk = clk_get(&gpio_pdev->dev, NULL);
1069        if (IS_ERR(clk)) {
1070                platform_device_put(gpio_pdev);
1071                return (void *) clk;
1072        }
1073        clk_prepare(clk);
1074        nmk_chip->clk = clk;
1075
1076        BUG_ON(nmk_chip->bank >= ARRAY_SIZE(nmk_gpio_chips));
1077        nmk_gpio_chips[id] = nmk_chip;
1078        return nmk_chip;
1079}
1080
1081static int nmk_gpio_probe(struct platform_device *dev)
1082{
1083        struct device_node *np = dev->dev.of_node;
1084        struct nmk_gpio_chip *nmk_chip;
1085        struct gpio_chip *chip;
1086        struct gpio_irq_chip *girq;
1087        struct irq_chip *irqchip;
1088        bool supports_sleepmode;
1089        int irq;
1090        int ret;
1091
1092        nmk_chip = nmk_gpio_populate_chip(np, dev);
1093        if (IS_ERR(nmk_chip)) {
1094                dev_err(&dev->dev, "could not populate nmk chip struct\n");
1095                return PTR_ERR(nmk_chip);
1096        }
1097
1098        supports_sleepmode =
1099                of_property_read_bool(np, "st,supports-sleepmode");
1100
1101        /* Correct platform device ID */
1102        dev->id = nmk_chip->bank;
1103
1104        irq = platform_get_irq(dev, 0);
1105        if (irq < 0)
1106                return irq;
1107
1108        /*
1109         * The virt address in nmk_chip->addr is in the nomadik register space,
1110         * so we can simply convert the resource address, without remapping
1111         */
1112        nmk_chip->sleepmode = supports_sleepmode;
1113        spin_lock_init(&nmk_chip->lock);
1114
1115        chip = &nmk_chip->chip;
1116        chip->request = gpiochip_generic_request;
1117        chip->free = gpiochip_generic_free;
1118        chip->get_direction = nmk_gpio_get_dir;
1119        chip->direction_input = nmk_gpio_make_input;
1120        chip->get = nmk_gpio_get_input;
1121        chip->direction_output = nmk_gpio_make_output;
1122        chip->set = nmk_gpio_set_output;
1123        chip->dbg_show = nmk_gpio_dbg_show;
1124        chip->can_sleep = false;
1125        chip->owner = THIS_MODULE;
1126
1127        irqchip = &nmk_chip->irqchip;
1128        irqchip->irq_ack = nmk_gpio_irq_ack;
1129        irqchip->irq_mask = nmk_gpio_irq_mask;
1130        irqchip->irq_unmask = nmk_gpio_irq_unmask;
1131        irqchip->irq_set_type = nmk_gpio_irq_set_type;
1132        irqchip->irq_set_wake = nmk_gpio_irq_set_wake;
1133        irqchip->irq_startup = nmk_gpio_irq_startup;
1134        irqchip->irq_shutdown = nmk_gpio_irq_shutdown;
1135        irqchip->flags = IRQCHIP_MASK_ON_SUSPEND;
1136        irqchip->name = kasprintf(GFP_KERNEL, "nmk%u-%u-%u",
1137                                  dev->id,
1138                                  chip->base,
1139                                  chip->base + chip->ngpio - 1);
1140
1141        girq = &chip->irq;
1142        girq->chip = irqchip;
1143        girq->parent_handler = nmk_gpio_irq_handler;
1144        girq->num_parents = 1;
1145        girq->parents = devm_kcalloc(&dev->dev, 1,
1146                                     sizeof(*girq->parents),
1147                                     GFP_KERNEL);
1148        if (!girq->parents)
1149                return -ENOMEM;
1150        girq->parents[0] = irq;
1151        girq->default_type = IRQ_TYPE_NONE;
1152        girq->handler = handle_edge_irq;
1153
1154        clk_enable(nmk_chip->clk);
1155        nmk_chip->lowemi = readl_relaxed(nmk_chip->addr + NMK_GPIO_LOWEMI);
1156        clk_disable(nmk_chip->clk);
1157        chip->of_node = np;
1158
1159        ret = gpiochip_add_data(chip, nmk_chip);
1160        if (ret)
1161                return ret;
1162
1163        platform_set_drvdata(dev, nmk_chip);
1164
1165        dev_info(&dev->dev, "chip registered\n");
1166
1167        return 0;
1168}
1169
1170static int nmk_get_groups_cnt(struct pinctrl_dev *pctldev)
1171{
1172        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
1173
1174        return npct->soc->ngroups;
1175}
1176
1177static const char *nmk_get_group_name(struct pinctrl_dev *pctldev,
1178                                       unsigned selector)
1179{
1180        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
1181
1182        return npct->soc->groups[selector].name;
1183}
1184
1185static int nmk_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector,
1186                              const unsigned **pins,
1187                              unsigned *num_pins)
1188{
1189        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
1190
1191        *pins = npct->soc->groups[selector].pins;
1192        *num_pins = npct->soc->groups[selector].npins;
1193        return 0;
1194}
1195
1196static struct nmk_gpio_chip *find_nmk_gpio_from_pin(unsigned pin)
1197{
1198        int i;
1199        struct nmk_gpio_chip *nmk_gpio;
1200
1201        for(i = 0; i < NMK_MAX_BANKS; i++) {
1202                nmk_gpio = nmk_gpio_chips[i];
1203                if (!nmk_gpio)
1204                        continue;
1205                if (pin >= nmk_gpio->chip.base &&
1206                        pin < nmk_gpio->chip.base + nmk_gpio->chip.ngpio)
1207                        return nmk_gpio;
1208        }
1209        return NULL;
1210}
1211
1212static struct gpio_chip *find_gc_from_pin(unsigned pin)
1213{
1214        struct nmk_gpio_chip *nmk_gpio = find_nmk_gpio_from_pin(pin);
1215
1216        if (nmk_gpio)
1217                return &nmk_gpio->chip;
1218        return NULL;
1219}
1220
1221static void nmk_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s,
1222                   unsigned offset)
1223{
1224        struct gpio_chip *chip = find_gc_from_pin(offset);
1225
1226        if (!chip) {
1227                seq_printf(s, "invalid pin offset");
1228                return;
1229        }
1230        nmk_gpio_dbg_show_one(s, pctldev, chip, offset - chip->base, offset);
1231}
1232
1233static int nmk_dt_add_map_mux(struct pinctrl_map **map, unsigned *reserved_maps,
1234                unsigned *num_maps, const char *group,
1235                const char *function)
1236{
1237        if (*num_maps == *reserved_maps)
1238                return -ENOSPC;
1239
1240        (*map)[*num_maps].type = PIN_MAP_TYPE_MUX_GROUP;
1241        (*map)[*num_maps].data.mux.group = group;
1242        (*map)[*num_maps].data.mux.function = function;
1243        (*num_maps)++;
1244
1245        return 0;
1246}
1247
1248static int nmk_dt_add_map_configs(struct pinctrl_map **map,
1249                unsigned *reserved_maps,
1250                unsigned *num_maps, const char *group,
1251                unsigned long *configs, unsigned num_configs)
1252{
1253        unsigned long *dup_configs;
1254
1255        if (*num_maps == *reserved_maps)
1256                return -ENOSPC;
1257
1258        dup_configs = kmemdup(configs, num_configs * sizeof(*dup_configs),
1259                              GFP_KERNEL);
1260        if (!dup_configs)
1261                return -ENOMEM;
1262
1263        (*map)[*num_maps].type = PIN_MAP_TYPE_CONFIGS_PIN;
1264
1265        (*map)[*num_maps].data.configs.group_or_pin = group;
1266        (*map)[*num_maps].data.configs.configs = dup_configs;
1267        (*map)[*num_maps].data.configs.num_configs = num_configs;
1268        (*num_maps)++;
1269
1270        return 0;
1271}
1272
1273#define NMK_CONFIG_PIN(x, y) { .property = x, .config = y, }
1274#define NMK_CONFIG_PIN_ARRAY(x, y) { .property = x, .choice = y, \
1275        .size = ARRAY_SIZE(y), }
1276
1277static const unsigned long nmk_pin_input_modes[] = {
1278        PIN_INPUT_NOPULL,
1279        PIN_INPUT_PULLUP,
1280        PIN_INPUT_PULLDOWN,
1281};
1282
1283static const unsigned long nmk_pin_output_modes[] = {
1284        PIN_OUTPUT_LOW,
1285        PIN_OUTPUT_HIGH,
1286        PIN_DIR_OUTPUT,
1287};
1288
1289static const unsigned long nmk_pin_sleep_modes[] = {
1290        PIN_SLEEPMODE_DISABLED,
1291        PIN_SLEEPMODE_ENABLED,
1292};
1293
1294static const unsigned long nmk_pin_sleep_input_modes[] = {
1295        PIN_SLPM_INPUT_NOPULL,
1296        PIN_SLPM_INPUT_PULLUP,
1297        PIN_SLPM_INPUT_PULLDOWN,
1298        PIN_SLPM_DIR_INPUT,
1299};
1300
1301static const unsigned long nmk_pin_sleep_output_modes[] = {
1302        PIN_SLPM_OUTPUT_LOW,
1303        PIN_SLPM_OUTPUT_HIGH,
1304        PIN_SLPM_DIR_OUTPUT,
1305};
1306
1307static const unsigned long nmk_pin_sleep_wakeup_modes[] = {
1308        PIN_SLPM_WAKEUP_DISABLE,
1309        PIN_SLPM_WAKEUP_ENABLE,
1310};
1311
1312static const unsigned long nmk_pin_gpio_modes[] = {
1313        PIN_GPIOMODE_DISABLED,
1314        PIN_GPIOMODE_ENABLED,
1315};
1316
1317static const unsigned long nmk_pin_sleep_pdis_modes[] = {
1318        PIN_SLPM_PDIS_DISABLED,
1319        PIN_SLPM_PDIS_ENABLED,
1320};
1321
1322struct nmk_cfg_param {
1323        const char *property;
1324        unsigned long config;
1325        const unsigned long *choice;
1326        int size;
1327};
1328
1329static const struct nmk_cfg_param nmk_cfg_params[] = {
1330        NMK_CONFIG_PIN_ARRAY("ste,input",               nmk_pin_input_modes),
1331        NMK_CONFIG_PIN_ARRAY("ste,output",              nmk_pin_output_modes),
1332        NMK_CONFIG_PIN_ARRAY("ste,sleep",               nmk_pin_sleep_modes),
1333        NMK_CONFIG_PIN_ARRAY("ste,sleep-input",         nmk_pin_sleep_input_modes),
1334        NMK_CONFIG_PIN_ARRAY("ste,sleep-output",        nmk_pin_sleep_output_modes),
1335        NMK_CONFIG_PIN_ARRAY("ste,sleep-wakeup",        nmk_pin_sleep_wakeup_modes),
1336        NMK_CONFIG_PIN_ARRAY("ste,gpio",                nmk_pin_gpio_modes),
1337        NMK_CONFIG_PIN_ARRAY("ste,sleep-pull-disable",  nmk_pin_sleep_pdis_modes),
1338};
1339
1340static int nmk_dt_pin_config(int index, int val, unsigned long *config)
1341{
1342        if (nmk_cfg_params[index].choice == NULL)
1343                *config = nmk_cfg_params[index].config;
1344        else {
1345                /* test if out of range */
1346                if  (val < nmk_cfg_params[index].size) {
1347                        *config = nmk_cfg_params[index].config |
1348                                nmk_cfg_params[index].choice[val];
1349                }
1350        }
1351        return 0;
1352}
1353
1354static const char *nmk_find_pin_name(struct pinctrl_dev *pctldev, const char *pin_name)
1355{
1356        int i, pin_number;
1357        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
1358
1359        if (sscanf((char *)pin_name, "GPIO%d", &pin_number) == 1)
1360                for (i = 0; i < npct->soc->npins; i++)
1361                        if (npct->soc->pins[i].number == pin_number)
1362                                return npct->soc->pins[i].name;
1363        return NULL;
1364}
1365
1366static bool nmk_pinctrl_dt_get_config(struct device_node *np,
1367                unsigned long *configs)
1368{
1369        bool has_config = 0;
1370        unsigned long cfg = 0;
1371        int i, val, ret;
1372
1373        for (i = 0; i < ARRAY_SIZE(nmk_cfg_params); i++) {
1374                ret = of_property_read_u32(np,
1375                                nmk_cfg_params[i].property, &val);
1376                if (ret != -EINVAL) {
1377                        if (nmk_dt_pin_config(i, val, &cfg) == 0) {
1378                                *configs |= cfg;
1379                                has_config = 1;
1380                        }
1381                }
1382        }
1383
1384        return has_config;
1385}
1386
1387static int nmk_pinctrl_dt_subnode_to_map(struct pinctrl_dev *pctldev,
1388                struct device_node *np,
1389                struct pinctrl_map **map,
1390                unsigned *reserved_maps,
1391                unsigned *num_maps)
1392{
1393        int ret;
1394        const char *function = NULL;
1395        unsigned long configs = 0;
1396        bool has_config = 0;
1397        struct property *prop;
1398        struct device_node *np_config;
1399
1400        ret = of_property_read_string(np, "function", &function);
1401        if (ret >= 0) {
1402                const char *group;
1403
1404                ret = of_property_count_strings(np, "groups");
1405                if (ret < 0)
1406                        goto exit;
1407
1408                ret = pinctrl_utils_reserve_map(pctldev, map,
1409                                                reserved_maps,
1410                                                num_maps, ret);
1411                if (ret < 0)
1412                        goto exit;
1413
1414                of_property_for_each_string(np, "groups", prop, group) {
1415                        ret = nmk_dt_add_map_mux(map, reserved_maps, num_maps,
1416                                          group, function);
1417                        if (ret < 0)
1418                                goto exit;
1419                }
1420        }
1421
1422        has_config = nmk_pinctrl_dt_get_config(np, &configs);
1423        np_config = of_parse_phandle(np, "ste,config", 0);
1424        if (np_config)
1425                has_config |= nmk_pinctrl_dt_get_config(np_config, &configs);
1426        if (has_config) {
1427                const char *gpio_name;
1428                const char *pin;
1429
1430                ret = of_property_count_strings(np, "pins");
1431                if (ret < 0)
1432                        goto exit;
1433                ret = pinctrl_utils_reserve_map(pctldev, map,
1434                                                reserved_maps,
1435                                                num_maps, ret);
1436                if (ret < 0)
1437                        goto exit;
1438
1439                of_property_for_each_string(np, "pins", prop, pin) {
1440                        gpio_name = nmk_find_pin_name(pctldev, pin);
1441
1442                        ret = nmk_dt_add_map_configs(map, reserved_maps,
1443                                                     num_maps,
1444                                                     gpio_name, &configs, 1);
1445                        if (ret < 0)
1446                                goto exit;
1447                }
1448        }
1449
1450exit:
1451        return ret;
1452}
1453
1454static int nmk_pinctrl_dt_node_to_map(struct pinctrl_dev *pctldev,
1455                                 struct device_node *np_config,
1456                                 struct pinctrl_map **map, unsigned *num_maps)
1457{
1458        unsigned reserved_maps;
1459        struct device_node *np;
1460        int ret;
1461
1462        reserved_maps = 0;
1463        *map = NULL;
1464        *num_maps = 0;
1465
1466        for_each_child_of_node(np_config, np) {
1467                ret = nmk_pinctrl_dt_subnode_to_map(pctldev, np, map,
1468                                &reserved_maps, num_maps);
1469                if (ret < 0) {
1470                        pinctrl_utils_free_map(pctldev, *map, *num_maps);
1471                        of_node_put(np);
1472                        return ret;
1473                }
1474        }
1475
1476        return 0;
1477}
1478
1479static const struct pinctrl_ops nmk_pinctrl_ops = {
1480        .get_groups_count = nmk_get_groups_cnt,
1481        .get_group_name = nmk_get_group_name,
1482        .get_group_pins = nmk_get_group_pins,
1483        .pin_dbg_show = nmk_pin_dbg_show,
1484        .dt_node_to_map = nmk_pinctrl_dt_node_to_map,
1485        .dt_free_map = pinctrl_utils_free_map,
1486};
1487
1488static int nmk_pmx_get_funcs_cnt(struct pinctrl_dev *pctldev)
1489{
1490        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
1491
1492        return npct->soc->nfunctions;
1493}
1494
1495static const char *nmk_pmx_get_func_name(struct pinctrl_dev *pctldev,
1496                                         unsigned function)
1497{
1498        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
1499
1500        return npct->soc->functions[function].name;
1501}
1502
1503static int nmk_pmx_get_func_groups(struct pinctrl_dev *pctldev,
1504                                   unsigned function,
1505                                   const char * const **groups,
1506                                   unsigned * const num_groups)
1507{
1508        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
1509
1510        *groups = npct->soc->functions[function].groups;
1511        *num_groups = npct->soc->functions[function].ngroups;
1512
1513        return 0;
1514}
1515
1516static int nmk_pmx_set(struct pinctrl_dev *pctldev, unsigned function,
1517                       unsigned group)
1518{
1519        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
1520        const struct nmk_pingroup *g;
1521        static unsigned int slpm[NUM_BANKS];
1522        unsigned long flags = 0;
1523        bool glitch;
1524        int ret = -EINVAL;
1525        int i;
1526
1527        g = &npct->soc->groups[group];
1528
1529        if (g->altsetting < 0)
1530                return -EINVAL;
1531
1532        dev_dbg(npct->dev, "enable group %s, %u pins\n", g->name, g->npins);
1533
1534        /*
1535         * If we're setting altfunc C by setting both AFSLA and AFSLB to 1,
1536         * we may pass through an undesired state. In this case we take
1537         * some extra care.
1538         *
1539         * Safe sequence used to switch IOs between GPIO and Alternate-C mode:
1540         *  - Save SLPM registers (since we have a shadow register in the
1541         *    nmk_chip we're using that as backup)
1542         *  - Set SLPM=0 for the IOs you want to switch and others to 1
1543         *  - Configure the GPIO registers for the IOs that are being switched
1544         *  - Set IOFORCE=1
1545         *  - Modify the AFLSA/B registers for the IOs that are being switched
1546         *  - Set IOFORCE=0
1547         *  - Restore SLPM registers
1548         *  - Any spurious wake up event during switch sequence to be ignored
1549         *    and cleared
1550         *
1551         * We REALLY need to save ALL slpm registers, because the external
1552         * IOFORCE will switch *all* ports to their sleepmode setting to as
1553         * to avoid glitches. (Not just one port!)
1554         */
1555        glitch = ((g->altsetting & NMK_GPIO_ALT_C) == NMK_GPIO_ALT_C);
1556
1557        if (glitch) {
1558                spin_lock_irqsave(&nmk_gpio_slpm_lock, flags);
1559
1560                /* Initially don't put any pins to sleep when switching */
1561                memset(slpm, 0xff, sizeof(slpm));
1562
1563                /*
1564                 * Then mask the pins that need to be sleeping now when we're
1565                 * switching to the ALT C function.
1566                 */
1567                for (i = 0; i < g->npins; i++)
1568                        slpm[g->pins[i] / NMK_GPIO_PER_CHIP] &= ~BIT(g->pins[i]);
1569                nmk_gpio_glitch_slpm_init(slpm);
1570        }
1571
1572        for (i = 0; i < g->npins; i++) {
1573                struct nmk_gpio_chip *nmk_chip;
1574                unsigned bit;
1575
1576                nmk_chip = find_nmk_gpio_from_pin(g->pins[i]);
1577                if (!nmk_chip) {
1578                        dev_err(npct->dev,
1579                                "invalid pin offset %d in group %s at index %d\n",
1580                                g->pins[i], g->name, i);
1581                        goto out_glitch;
1582                }
1583                dev_dbg(npct->dev, "setting pin %d to altsetting %d\n", g->pins[i], g->altsetting);
1584
1585                clk_enable(nmk_chip->clk);
1586                bit = g->pins[i] % NMK_GPIO_PER_CHIP;
1587                /*
1588                 * If the pin is switching to altfunc, and there was an
1589                 * interrupt installed on it which has been lazy disabled,
1590                 * actually mask the interrupt to prevent spurious interrupts
1591                 * that would occur while the pin is under control of the
1592                 * peripheral. Only SKE does this.
1593                 */
1594                nmk_gpio_disable_lazy_irq(nmk_chip, bit);
1595
1596                __nmk_gpio_set_mode_safe(nmk_chip, bit,
1597                        (g->altsetting & NMK_GPIO_ALT_C), glitch);
1598                clk_disable(nmk_chip->clk);
1599
1600                /*
1601                 * Call PRCM GPIOCR config function in case ALTC
1602                 * has been selected:
1603                 * - If selection is a ALTCx, some bits in PRCM GPIOCR registers
1604                 *   must be set.
1605                 * - If selection is pure ALTC and previous selection was ALTCx,
1606                 *   then some bits in PRCM GPIOCR registers must be cleared.
1607                 */
1608                if ((g->altsetting & NMK_GPIO_ALT_C) == NMK_GPIO_ALT_C)
1609                        nmk_prcm_altcx_set_mode(npct, g->pins[i],
1610                                g->altsetting >> NMK_GPIO_ALT_CX_SHIFT);
1611        }
1612
1613        /* When all pins are successfully reconfigured we get here */
1614        ret = 0;
1615
1616out_glitch:
1617        if (glitch) {
1618                nmk_gpio_glitch_slpm_restore(slpm);
1619                spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags);
1620        }
1621
1622        return ret;
1623}
1624
1625static int nmk_gpio_request_enable(struct pinctrl_dev *pctldev,
1626                                   struct pinctrl_gpio_range *range,
1627                                   unsigned offset)
1628{
1629        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
1630        struct nmk_gpio_chip *nmk_chip;
1631        struct gpio_chip *chip;
1632        unsigned bit;
1633
1634        if (!range) {
1635                dev_err(npct->dev, "invalid range\n");
1636                return -EINVAL;
1637        }
1638        if (!range->gc) {
1639                dev_err(npct->dev, "missing GPIO chip in range\n");
1640                return -EINVAL;
1641        }
1642        chip = range->gc;
1643        nmk_chip = gpiochip_get_data(chip);
1644
1645        dev_dbg(npct->dev, "enable pin %u as GPIO\n", offset);
1646
1647        clk_enable(nmk_chip->clk);
1648        bit = offset % NMK_GPIO_PER_CHIP;
1649        /* There is no glitch when converting any pin to GPIO */
1650        __nmk_gpio_set_mode(nmk_chip, bit, NMK_GPIO_ALT_GPIO);
1651        clk_disable(nmk_chip->clk);
1652
1653        return 0;
1654}
1655
1656static void nmk_gpio_disable_free(struct pinctrl_dev *pctldev,
1657                                  struct pinctrl_gpio_range *range,
1658                                  unsigned offset)
1659{
1660        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
1661
1662        dev_dbg(npct->dev, "disable pin %u as GPIO\n", offset);
1663        /* Set the pin to some default state, GPIO is usually default */
1664}
1665
1666static const struct pinmux_ops nmk_pinmux_ops = {
1667        .get_functions_count = nmk_pmx_get_funcs_cnt,
1668        .get_function_name = nmk_pmx_get_func_name,
1669        .get_function_groups = nmk_pmx_get_func_groups,
1670        .set_mux = nmk_pmx_set,
1671        .gpio_request_enable = nmk_gpio_request_enable,
1672        .gpio_disable_free = nmk_gpio_disable_free,
1673        .strict = true,
1674};
1675
1676static int nmk_pin_config_get(struct pinctrl_dev *pctldev, unsigned pin,
1677                              unsigned long *config)
1678{
1679        /* Not implemented */
1680        return -EINVAL;
1681}
1682
1683static int nmk_pin_config_set(struct pinctrl_dev *pctldev, unsigned pin,
1684                              unsigned long *configs, unsigned num_configs)
1685{
1686        static const char *pullnames[] = {
1687                [NMK_GPIO_PULL_NONE]    = "none",
1688                [NMK_GPIO_PULL_UP]      = "up",
1689                [NMK_GPIO_PULL_DOWN]    = "down",
1690                [3] /* illegal */       = "??"
1691        };
1692        static const char *slpmnames[] = {
1693                [NMK_GPIO_SLPM_INPUT]           = "input/wakeup",
1694                [NMK_GPIO_SLPM_NOCHANGE]        = "no-change/no-wakeup",
1695        };
1696        struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev);
1697        struct nmk_gpio_chip *nmk_chip;
1698        unsigned bit;
1699        pin_cfg_t cfg;
1700        int pull, slpm, output, val, i;
1701        bool lowemi, gpiomode, sleep;
1702
1703        nmk_chip = find_nmk_gpio_from_pin(pin);
1704        if (!nmk_chip) {
1705                dev_err(npct->dev,
1706                        "invalid pin offset %d\n", pin);
1707                return -EINVAL;
1708        }
1709
1710        for (i = 0; i < num_configs; i++) {
1711                /*
1712                 * The pin config contains pin number and altfunction fields,
1713                 * here we just ignore that part. It's being handled by the
1714                 * framework and pinmux callback respectively.
1715                 */
1716                cfg = (pin_cfg_t) configs[i];
1717                pull = PIN_PULL(cfg);
1718                slpm = PIN_SLPM(cfg);
1719                output = PIN_DIR(cfg);
1720                val = PIN_VAL(cfg);
1721                lowemi = PIN_LOWEMI(cfg);
1722                gpiomode = PIN_GPIOMODE(cfg);
1723                sleep = PIN_SLEEPMODE(cfg);
1724
1725                if (sleep) {
1726                        int slpm_pull = PIN_SLPM_PULL(cfg);
1727                        int slpm_output = PIN_SLPM_DIR(cfg);
1728                        int slpm_val = PIN_SLPM_VAL(cfg);
1729
1730                        /* All pins go into GPIO mode at sleep */
1731                        gpiomode = true;
1732
1733                        /*
1734                         * The SLPM_* values are normal values + 1 to allow zero
1735                         * to mean "same as normal".
1736                         */
1737                        if (slpm_pull)
1738                                pull = slpm_pull - 1;
1739                        if (slpm_output)
1740                                output = slpm_output - 1;
1741                        if (slpm_val)
1742                                val = slpm_val - 1;
1743
1744                        dev_dbg(nmk_chip->chip.parent,
1745                                "pin %d: sleep pull %s, dir %s, val %s\n",
1746                                pin,
1747                                slpm_pull ? pullnames[pull] : "same",
1748                                slpm_output ? (output ? "output" : "input")
1749                                : "same",
1750                                slpm_val ? (val ? "high" : "low") : "same");
1751                }
1752
1753                dev_dbg(nmk_chip->chip.parent,
1754                        "pin %d [%#lx]: pull %s, slpm %s (%s%s), lowemi %s\n",
1755                        pin, cfg, pullnames[pull], slpmnames[slpm],
1756                        output ? "output " : "input",
1757                        output ? (val ? "high" : "low") : "",
1758                        lowemi ? "on" : "off");
1759
1760                clk_enable(nmk_chip->clk);
1761                bit = pin % NMK_GPIO_PER_CHIP;
1762                if (gpiomode)
1763                        /* No glitch when going to GPIO mode */
1764                        __nmk_gpio_set_mode(nmk_chip, bit, NMK_GPIO_ALT_GPIO);
1765                if (output)
1766                        __nmk_gpio_make_output(nmk_chip, bit, val);
1767                else {
1768                        __nmk_gpio_make_input(nmk_chip, bit);
1769                        __nmk_gpio_set_pull(nmk_chip, bit, pull);
1770                }
1771                /* TODO: isn't this only applicable on output pins? */
1772                __nmk_gpio_set_lowemi(nmk_chip, bit, lowemi);
1773
1774                __nmk_gpio_set_slpm(nmk_chip, bit, slpm);
1775                clk_disable(nmk_chip->clk);
1776        } /* for each config */
1777
1778        return 0;
1779}
1780
1781static const struct pinconf_ops nmk_pinconf_ops = {
1782        .pin_config_get = nmk_pin_config_get,
1783        .pin_config_set = nmk_pin_config_set,
1784};
1785
1786static struct pinctrl_desc nmk_pinctrl_desc = {
1787        .name = "pinctrl-nomadik",
1788        .pctlops = &nmk_pinctrl_ops,
1789        .pmxops = &nmk_pinmux_ops,
1790        .confops = &nmk_pinconf_ops,
1791        .owner = THIS_MODULE,
1792};
1793
1794static const struct of_device_id nmk_pinctrl_match[] = {
1795        {
1796                .compatible = "stericsson,stn8815-pinctrl",
1797                .data = (void *)PINCTRL_NMK_STN8815,
1798        },
1799        {
1800                .compatible = "stericsson,db8500-pinctrl",
1801                .data = (void *)PINCTRL_NMK_DB8500,
1802        },
1803        {
1804                .compatible = "stericsson,db8540-pinctrl",
1805                .data = (void *)PINCTRL_NMK_DB8540,
1806        },
1807        {},
1808};
1809
1810#ifdef CONFIG_PM_SLEEP
1811static int nmk_pinctrl_suspend(struct device *dev)
1812{
1813        struct nmk_pinctrl *npct;
1814
1815        npct = dev_get_drvdata(dev);
1816        if (!npct)
1817                return -EINVAL;
1818
1819        return pinctrl_force_sleep(npct->pctl);
1820}
1821
1822static int nmk_pinctrl_resume(struct device *dev)
1823{
1824        struct nmk_pinctrl *npct;
1825
1826        npct = dev_get_drvdata(dev);
1827        if (!npct)
1828                return -EINVAL;
1829
1830        return pinctrl_force_default(npct->pctl);
1831}
1832#endif
1833
1834static int nmk_pinctrl_probe(struct platform_device *pdev)
1835{
1836        const struct of_device_id *match;
1837        struct device_node *np = pdev->dev.of_node;
1838        struct device_node *prcm_np;
1839        struct nmk_pinctrl *npct;
1840        unsigned int version = 0;
1841        int i;
1842
1843        npct = devm_kzalloc(&pdev->dev, sizeof(*npct), GFP_KERNEL);
1844        if (!npct)
1845                return -ENOMEM;
1846
1847        match = of_match_device(nmk_pinctrl_match, &pdev->dev);
1848        if (!match)
1849                return -ENODEV;
1850        version = (unsigned int) match->data;
1851
1852        /* Poke in other ASIC variants here */
1853        if (version == PINCTRL_NMK_STN8815)
1854                nmk_pinctrl_stn8815_init(&npct->soc);
1855        if (version == PINCTRL_NMK_DB8500)
1856                nmk_pinctrl_db8500_init(&npct->soc);
1857        if (version == PINCTRL_NMK_DB8540)
1858                nmk_pinctrl_db8540_init(&npct->soc);
1859
1860        /*
1861         * Since we depend on the GPIO chips to provide clock and register base
1862         * for the pin control operations, make sure that we have these
1863         * populated before we continue. Follow the phandles to instantiate
1864         * them. The GPIO portion of the actual hardware may be probed before
1865         * or after this point: it shouldn't matter as the APIs are orthogonal.
1866         */
1867        for (i = 0; i < NMK_MAX_BANKS; i++) {
1868                struct device_node *gpio_np;
1869                struct nmk_gpio_chip *nmk_chip;
1870
1871                gpio_np = of_parse_phandle(np, "nomadik-gpio-chips", i);
1872                if (gpio_np) {
1873                        dev_info(&pdev->dev,
1874                                 "populate NMK GPIO %d \"%pOFn\"\n",
1875                                 i, gpio_np);
1876                        nmk_chip = nmk_gpio_populate_chip(gpio_np, pdev);
1877                        if (IS_ERR(nmk_chip))
1878                                dev_err(&pdev->dev,
1879                                        "could not populate nmk chip struct "
1880                                        "- continue anyway\n");
1881                        of_node_put(gpio_np);
1882                }
1883        }
1884
1885        prcm_np = of_parse_phandle(np, "prcm", 0);
1886        if (prcm_np)
1887                npct->prcm_base = of_iomap(prcm_np, 0);
1888        if (!npct->prcm_base) {
1889                if (version == PINCTRL_NMK_STN8815) {
1890                        dev_info(&pdev->dev,
1891                                 "No PRCM base, "
1892                                 "assuming no ALT-Cx control is available\n");
1893                } else {
1894                        dev_err(&pdev->dev, "missing PRCM base address\n");
1895                        return -EINVAL;
1896                }
1897        }
1898
1899        nmk_pinctrl_desc.pins = npct->soc->pins;
1900        nmk_pinctrl_desc.npins = npct->soc->npins;
1901        npct->dev = &pdev->dev;
1902
1903        npct->pctl = devm_pinctrl_register(&pdev->dev, &nmk_pinctrl_desc, npct);
1904        if (IS_ERR(npct->pctl)) {
1905                dev_err(&pdev->dev, "could not register Nomadik pinctrl driver\n");
1906                return PTR_ERR(npct->pctl);
1907        }
1908
1909        platform_set_drvdata(pdev, npct);
1910        dev_info(&pdev->dev, "initialized Nomadik pin control driver\n");
1911
1912        return 0;
1913}
1914
1915static const struct of_device_id nmk_gpio_match[] = {
1916        { .compatible = "st,nomadik-gpio", },
1917        {}
1918};
1919
1920static struct platform_driver nmk_gpio_driver = {
1921        .driver = {
1922                .name = "gpio",
1923                .of_match_table = nmk_gpio_match,
1924        },
1925        .probe = nmk_gpio_probe,
1926};
1927
1928static SIMPLE_DEV_PM_OPS(nmk_pinctrl_pm_ops,
1929                        nmk_pinctrl_suspend,
1930                        nmk_pinctrl_resume);
1931
1932static struct platform_driver nmk_pinctrl_driver = {
1933        .driver = {
1934                .name = "pinctrl-nomadik",
1935                .of_match_table = nmk_pinctrl_match,
1936                .pm = &nmk_pinctrl_pm_ops,
1937        },
1938        .probe = nmk_pinctrl_probe,
1939};
1940
1941static int __init nmk_gpio_init(void)
1942{
1943        return platform_driver_register(&nmk_gpio_driver);
1944}
1945subsys_initcall(nmk_gpio_init);
1946
1947static int __init nmk_pinctrl_init(void)
1948{
1949        return platform_driver_register(&nmk_pinctrl_driver);
1950}
1951core_initcall(nmk_pinctrl_init);
1952