1
2
3
4
5
6config NET_TULIP
7 bool "DEC - Tulip devices"
8 depends on (PCI || EISA || CARDBUS)
9 help
10 This selects the "Tulip" family of EISA/PCI network cards.
11
12if NET_TULIP
13
14config DE2104X
15 tristate "Early DECchip Tulip (dc2104x) PCI support"
16 depends on PCI
17 select CRC32
18 help
19 This driver is developed for the SMC EtherPower series Ethernet
20 cards and also works with cards based on the DECchip
21 21040 (Tulip series) chips. Some LinkSys PCI cards are
22 of this type. (If your card is NOT SMC EtherPower 10/100 PCI
23 (smc9332dst), you can also try the driver for "Generic DECchip"
24 cards, below. However, most people with a network card of this type
25 will say Y here.)
26
27 To compile this driver as a module, choose M here. The module will
28 be called de2104x.
29
30config DE2104X_DSL
31 int "Descriptor Skip Length in 32 bit longwords"
32 depends on DE2104X
33 range 0 31
34 default 0
35 help
36 Setting this value allows to align ring buffer descriptors into their
37 own cache lines. Value of 4 corresponds to the typical 32 byte line
38 (the descriptor is 16 bytes). This is necessary on systems that lack
39 cache coherence, an example is PowerMac 5500. Otherwise 0 is safe.
40 Default is 0, and range is 0 to 31.
41
42config TULIP
43 tristate "DECchip Tulip (dc2114x) PCI support"
44 depends on PCI
45 select CRC32
46 help
47 This driver is developed for the SMC EtherPower series Ethernet
48 cards and also works with cards based on the DECchip
49 21140 (Tulip series) chips. Some LinkSys PCI cards are
50 of this type. (If your card is NOT SMC EtherPower 10/100 PCI
51 (smc9332dst), you can also try the driver for "Generic DECchip"
52 cards, above. However, most people with a network card of this type
53 will say Y here.)
54
55 To compile this driver as a module, choose M here. The module will
56 be called tulip.
57
58config TULIP_MWI
59 bool "New bus configuration"
60 depends on TULIP
61 help
62 This configures your Tulip card specifically for the card and
63 system cache line size type you are using.
64
65 This is experimental code, not yet tested on many boards.
66
67 If unsure, say N.
68
69config TULIP_MMIO
70 bool "Use PCI shared mem for NIC registers"
71 depends on TULIP
72 help
73 Use PCI shared memory for the NIC registers, rather than going through
74 the Tulip's PIO (programmed I/O ports). Faster, but could produce
75 obscure bugs if your mainboard has memory controller timing issues.
76 If in doubt, say N.
77
78config TULIP_NAPI
79 bool "Use RX polling (NAPI)"
80 depends on TULIP
81 help
82 NAPI is a new driver API designed to reduce CPU and interrupt load
83 when the driver is receiving lots of packets from the card. It is
84 still somewhat experimental and thus not yet enabled by default.
85
86 If your estimated Rx load is 10kpps or more, or if the card will be
87 deployed on potentially unfriendly networks (e.g. in a firewall),
88 then say Y here.
89
90 If in doubt, say N.
91
92config TULIP_NAPI_HW_MITIGATION
93 bool "Use Interrupt Mitigation"
94 depends on TULIP_NAPI
95 help
96 Use HW to reduce RX interrupts. Not strictly necessary since NAPI
97 reduces RX interrupts by itself. Interrupt mitigation reduces RX
98 interrupts even at low levels of traffic at the cost of a small
99 latency.
100
101 If in doubt, say Y.
102
103config TULIP_DM910X
104 def_bool y
105 depends on TULIP && SPARC
106
107config DE4X5
108 tristate "Generic DECchip & DIGITAL EtherWORKS PCI/EISA"
109 depends on (PCI || EISA)
110 depends on VIRT_TO_BUS || ALPHA || PPC || SPARC
111 select CRC32
112 help
113 This is support for the DIGITAL series of PCI/EISA Ethernet cards.
114 These include the DE425, DE434, DE435, DE450 and DE500 models. If
115 you have a network card of this type, say Y. More specific
116 information is contained in
117 <file:Documentation/networking/device_drivers/ethernet/dec/de4x5.rst>.
118
119 To compile this driver as a module, choose M here. The module will
120 be called de4x5.
121
122config WINBOND_840
123 tristate "Winbond W89c840 Ethernet support"
124 depends on PCI
125 select CRC32
126 select MII
127 help
128 This driver is for the Winbond W89c840 chip. It also works with
129 the TX9882 chip on the Compex RL100-ATX board.
130 More specific information and updates are available from
131 <http://www.scyld.com/network/drivers.html>.
132
133config DM9102
134 tristate "Davicom DM910x/DM980x support"
135 depends on PCI
136 select CRC32
137 help
138 This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from
139 Davicom (<http://www.davicom.com.tw/>). If you have such a network
140 (Ethernet) card, say Y. Some information is contained in the file
141 <file:Documentation/networking/device_drivers/ethernet/dec/dmfe.rst>.
142
143 To compile this driver as a module, choose M here. The module will
144 be called dmfe.
145
146config ULI526X
147 tristate "ULi M526x controller support"
148 depends on PCI
149 select CRC32
150 help
151 This driver is for ULi M5261/M5263 10/100M Ethernet Controller
152 (<http://www.nvidia.com/page/uli_drivers.html>).
153
154 To compile this driver as a module, choose M here. The module will
155 be called uli526x.
156
157config PCMCIA_XIRCOM
158 tristate "Xircom CardBus support"
159 depends on CARDBUS
160 help
161 This driver is for the Digital "Tulip" Ethernet CardBus adapters.
162 It should work with most DEC 21*4*-based chips/ethercards, as well
163 as with work-alike chips from Lite-On (PNIC) and Macronix (MXIC) and
164 ASIX.
165
166 To compile this driver as a module, choose M here. The module will
167 be called xircom_cb. If unsure, say N.
168
169endif
170
