/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
 * Device driver for the SYMBIOS/LSILOGIC 53C8XX and 53C1010 family 
 * of PCI-SCSI IO processors.
 *
 * Copyright (C) 1999-2001  Gerard Roudier <groudier@free.fr>
 *
 * This driver is derived from the Linux sym53c8xx driver.
 * Copyright (C) 1998-2000  Gerard Roudier
 *
 * The sym53c8xx driver is derived from the ncr53c8xx driver that had been 
 * a port of the FreeBSD ncr driver to Linux-1.2.13.
 *
 * The original ncr driver has been written for 386bsd and FreeBSD by
 *         Wolfgang Stanglmeier        <wolf@cologne.de>
 *         Stefan Esser                <se@mi.Uni-Koeln.de>
 * Copyright (C) 1994  Wolfgang Stanglmeier
 *
 * Other major contributions:
 *
 * NVRAM detection and reading.
 * Copyright (C) 1997 Richard Waltham <dormouse@farsrobt.demon.co.uk>
 *
 *-----------------------------------------------------------------------------
 */

/*
 *  Scripts for SYMBIOS-Processor
 *
 *  We have to know the offsets of all labels before we reach 
 *  them (for forward jumps). Therefore we declare a struct 
 *  here. If you make changes inside the script,
 *
 *  DONT FORGET TO CHANGE THE LENGTHS HERE!
 */

/*
 *  Script fragments which are loaded into the on-chip RAM 
 *  of 825A, 875, 876, 895, 895A, 896 and 1010 chips.
 *  Must not exceed 4K bytes.
 */
struct SYM_FWA_SCR {
        u32 start               [ 11];
        u32 getjob_begin        [  4];
        u32 _sms_a10            [  5];
        u32 getjob_end          [  4];
        u32 _sms_a20            [  4];
#ifdef SYM_CONF_TARGET_ROLE_SUPPORT
        u32 select              [  8];
#else
        u32 select              [  6];
#endif
        u32 _sms_a30            [  5];
        u32 wf_sel_done         [  2];
        u32 send_ident          [  2];
#ifdef SYM_CONF_IARB_SUPPORT
        u32 select2             [  8];
#else
        u32 select2             [  2];
#endif
        u32 command             [  2];
        u32 dispatch            [ 28];
        u32 sel_no_cmd          [ 10];
        u32 init                [  6];
        u32 clrack              [  4];
        u32 datai_done          [ 11];
        u32 datai_done_wsr      [ 20];
        u32 datao_done          [ 11];
        u32 datao_done_wss      [  6];
        u32 datai_phase         [  5];
        u32 datao_phase         [  5];
        u32 msg_in              [  2];
        u32 msg_in2             [ 10];
#ifdef SYM_CONF_IARB_SUPPORT
        u32 status              [ 14];
#else
        u32 status              [ 10];
#endif
        u32 complete            [  6];
        u32 complete2           [  8];
        u32 _sms_a40            [ 12];
        u32 done                [  5];
        u32 _sms_a50            [  5];
        u32 _sms_a60            [  2];
        u32 done_end            [  4];
        u32 complete_error      [  5];
        u32 save_dp             [ 11];
        u32 restore_dp          [  7];
        u32 disconnect          [ 11];
        u32 disconnect2         [  5];
        u32 _sms_a65            [  3];
#ifdef SYM_CONF_IARB_SUPPORT
        u32 idle                [  4];
#else
        u32 idle                [  2];
#endif
#ifdef SYM_CONF_IARB_SUPPORT
        u32 ungetjob            [  7];
#else
        u32 ungetjob            [  5];
#endif
#ifdef SYM_CONF_TARGET_ROLE_SUPPORT
        u32 reselect            [  4];
#else
        u32 reselect            [  2];
#endif
        u32 reselected          [ 19];
        u32 _sms_a70            [  6];
        u32 _sms_a80            [  4];
        u32 reselected1         [ 25];
        u32 _sms_a90            [  4];
        u32 resel_lun0          [  7];
        u32 _sms_a100           [  4];
        u32 resel_tag           [  8];
#if   SYM_CONF_MAX_TASK*4 > 512
        u32 _sms_a110           [ 23];
#elif SYM_CONF_MAX_TASK*4 > 256
        u32 _sms_a110           [ 17];
#else
        u32 _sms_a110           [ 13];
#endif
        u32 _sms_a120           [  2];
        u32 resel_go            [  4];
        u32 _sms_a130           [  7];
        u32 resel_dsa           [  2];
        u32 resel_dsa1          [  4];
        u32 _sms_a140           [  7];
        u32 resel_no_tag        [  4];
        u32 _sms_a145           [  7];
        u32 data_in             [SYM_CONF_MAX_SG * 2];
        u32 data_in2            [  4];
        u32 data_out            [SYM_CONF_MAX_SG * 2];
        u32 data_out2           [  4];
        u32 pm0_data            [ 12];
        u32 pm0_data_out        [  6];
        u32 pm0_data_end        [  7];
        u32 pm_data_end         [  4];
        u32 _sms_a150           [  4];
        u32 pm1_data            [ 12];
        u32 pm1_data_out        [  6];
        u32 pm1_data_end        [  9];
};

/*
 *  Script fragments which stay in main memory for all chips 
 *  except for chips that support 8K on-chip RAM.
 */
struct SYM_FWB_SCR {
        u32 no_data             [  2];
#ifdef SYM_CONF_TARGET_ROLE_SUPPORT
        u32 sel_for_abort       [ 18];
#else
        u32 sel_for_abort       [ 16];
#endif
        u32 sel_for_abort_1     [  2];
        u32 msg_in_etc          [ 12];
        u32 msg_received        [  5];
        u32 msg_weird_seen      [  5];
        u32 msg_extended        [ 17];
        u32 _sms_b10            [  4];
        u32 msg_bad             [  6];
        u32 msg_weird           [  4];
        u32 msg_weird1          [  8];
        u32 wdtr_resp           [  6];
        u32 send_wdtr           [  4];
        u32 sdtr_resp           [  6];
        u32 send_sdtr           [  4];
        u32 ppr_resp            [  6];
        u32 send_ppr            [  4];
        u32 nego_bad_phase      [  4];
        u32 msg_out             [  4];
        u32 msg_out_done        [  4];
        u32 data_ovrun          [  3];
        u32 data_ovrun1         [ 22];
        u32 data_ovrun2         [  8];
        u32 abort_resel         [ 16];
        u32 resend_ident        [  4];
        u32 ident_break         [  4];
        u32 ident_break_atn     [  4];
        u32 sdata_in            [  6];
        u32 resel_bad_lun       [  4];
        u32 bad_i_t_l           [  4];
        u32 bad_i_t_l_q         [  4];
        u32 bad_status          [  7];
        u32 wsr_ma_helper       [  4];

        /* Data area */
        u32 zero                [  1];
        u32 scratch             [  1];
        u32 scratch1            [  1];
        u32 prev_done           [  1];
        u32 done_pos            [  1];
        u32 nextjob             [  1];
        u32 startpos            [  1];
        u32 targtbl             [  1];
};

/*
 *  Script fragments used at initialisations.
 *  Only runs out of main memory.
 */
struct SYM_FWZ_SCR {
        u32 snooptest           [  9];
        u32 snoopend            [  2];
};

static struct SYM_FWA_SCR SYM_FWA_SCR = {
/*--------------------------< START >----------------------------*/ {
        /*
         *  Switch the LED on.
         *  Will be patched with a NO_OP if LED
         *  not needed or not desired.
         */
        SCR_REG_REG (gpreg, SCR_AND, 0xfe),
                0,
        /*
         *      Clear SIGP.
         */
        SCR_FROM_REG (ctest2),
                0,
        /*
         *  Stop here if the C code wants to perform 
         *  some error recovery procedure manually.
         *  (Indicate this by setting SEM in ISTAT)
         */
        SCR_FROM_REG (istat),
                0,
        /*
         *  Report to the C code the next position in 
         *  the start queue the SCRIPTS will schedule.
         *  The C code must not change SCRATCHA.
         */
        SCR_COPY (4),
                PADDR_B (startpos),
                RADDR_1 (scratcha),
        SCR_INT ^ IFTRUE (MASK (SEM, SEM)),
                SIR_SCRIPT_STOPPED,
        /*
         *  Start the next job.
         *
         *  @DSA     = start point for this job.
         *  SCRATCHA = address of this job in the start queue.
         *
         *  We will restore startpos with SCRATCHA if we fails the 
         *  arbitration or if it is the idle job.
         *
         *  The below GETJOB_BEGIN to GETJOB_END section of SCRIPTS 
         *  is a critical path. If it is partially executed, it then 
         *  may happen that the job address is not yet in the DSA 
         *  and the next queue position points to the next JOB.
         */
}/*-------------------------< GETJOB_BEGIN >---------------------*/,{
        /*
         *  Copy to a fixed location both the next STARTPOS 
         *  and the current JOB address, using self modifying 
         *  SCRIPTS.
         */
        SCR_COPY (4),
                RADDR_1 (scratcha),
                PADDR_A (_sms_a10),
        SCR_COPY (8),
}/*-------------------------< _SMS_A10 >-------------------------*/,{
                0,
                PADDR_B (nextjob),
        /*
         *  Move the start address to TEMP using self-
         *  modifying SCRIPTS and jump indirectly to 
         *  that address.
         */
        SCR_COPY (4),
                PADDR_B (nextjob),
                RADDR_1 (dsa),
}/*-------------------------< GETJOB_END >-----------------------*/,{
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a20),
        SCR_COPY (4),
}/*-------------------------< _SMS_A20 >-------------------------*/,{
                0,
                RADDR_1 (temp),
        SCR_RETURN,
                0,
}/*-------------------------< SELECT >---------------------------*/,{
        /*
         *  DSA contains the address of a scheduled
         *      data structure.
         *
         *  SCRATCHA contains the address of the start queue  
         *      entry which points to the next job.
         *
         *  Set Initiator mode.
         *
         *  (Target mode is left as an exercise for the reader)
         */
#ifdef SYM_CONF_TARGET_ROLE_SUPPORT
        SCR_CLR (SCR_TRG),
                0,
#endif
        /*
         *      And try to select this target.
         */
        SCR_SEL_TBL_ATN ^ offsetof (struct sym_dsb, select),
                PADDR_A (ungetjob),
        /*
         *  Now there are 4 possibilities:
         *
         *  (1) The chip loses arbitration.
         *  This is ok, because it will try again,
         *  when the bus becomes idle.
         *  (But beware of the timeout function!)
         *
         *  (2) The chip is reselected.
         *  Then the script processor takes the jump
         *  to the RESELECT label.
         *
         *  (3) The chip wins arbitration.
         *  Then it will execute SCRIPTS instruction until 
         *  the next instruction that checks SCSI phase.
         *  Then will stop and wait for selection to be 
         *  complete or selection time-out to occur.
         *
         *  After having won arbitration, the SCRIPTS  
         *  processor is able to execute instructions while 
         *  the SCSI core is performing SCSI selection.
         */

        /*
         *  Copy the CCB header to a fixed location 
         *  in the HCB using self-modifying SCRIPTS.
         */
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a30),
        SCR_COPY (sizeof(struct sym_ccbh)),
}/*-------------------------< _SMS_A30 >-------------------------*/,{
                0,
                HADDR_1 (ccb_head),
        /*
         *  Initialize the status register
         */
        SCR_COPY (4),
                HADDR_1 (ccb_head.status),
                RADDR_1 (scr0),
}/*-------------------------< WF_SEL_DONE >----------------------*/,{
        SCR_INT ^ IFFALSE (WHEN (SCR_MSG_OUT)),
                SIR_SEL_ATN_NO_MSG_OUT,
}/*-------------------------< SEND_IDENT >-----------------------*/,{
        /*
         *  Selection complete.
         *  Send the IDENTIFY and possibly the TAG message 
         *  and negotiation message if present.
         */
        SCR_MOVE_TBL ^ SCR_MSG_OUT,
                offsetof (struct sym_dsb, smsg),
}/*-------------------------< SELECT2 >--------------------------*/,{
#ifdef SYM_CONF_IARB_SUPPORT
        /*
         *  Set IMMEDIATE ARBITRATION if we have been given 
         *  a hint to do so. (Some job to do after this one).
         */
        SCR_FROM_REG (HF_REG),
                0,
        SCR_JUMPR ^ IFFALSE (MASK (HF_HINT_IARB, HF_HINT_IARB)),
                8,
        SCR_REG_REG (scntl1, SCR_OR, IARB),
                0,
#endif
        /*
         *  Anticipate the COMMAND phase.
         *  This is the PHASE we expect at this point.
         */
        SCR_JUMP ^ IFFALSE (WHEN (SCR_COMMAND)),
                PADDR_A (sel_no_cmd),
}/*-------------------------< COMMAND >--------------------------*/,{
        /*
         *  ... and send the command
         */
        SCR_MOVE_TBL ^ SCR_COMMAND,
                offsetof (struct sym_dsb, cmd),
}/*-------------------------< DISPATCH >-------------------------*/,{
        /*
         *  MSG_IN is the only phase that shall be 
         *  entered at least once for each (re)selection.
         *  So we test it first.
         */
        SCR_JUMP ^ IFTRUE (WHEN (SCR_MSG_IN)),
                PADDR_A (msg_in),
        SCR_JUMP ^ IFTRUE (IF (SCR_DATA_OUT)),
                PADDR_A (datao_phase),
        SCR_JUMP ^ IFTRUE (IF (SCR_DATA_IN)),
                PADDR_A (datai_phase),
        SCR_JUMP ^ IFTRUE (IF (SCR_STATUS)),
                PADDR_A (status),
        SCR_JUMP ^ IFTRUE (IF (SCR_COMMAND)),
                PADDR_A (command),
        SCR_JUMP ^ IFTRUE (IF (SCR_MSG_OUT)),
                PADDR_B (msg_out),
        /*
         *  Discard as many illegal phases as 
         *  required and tell the C code about.
         */
        SCR_JUMPR ^ IFFALSE (WHEN (SCR_ILG_OUT)),
                16,
        SCR_MOVE_ABS (1) ^ SCR_ILG_OUT,
                HADDR_1 (scratch),
        SCR_JUMPR ^ IFTRUE (WHEN (SCR_ILG_OUT)),
                -16,
        SCR_JUMPR ^ IFFALSE (WHEN (SCR_ILG_IN)),
                16,
        SCR_MOVE_ABS (1) ^ SCR_ILG_IN,
                HADDR_1 (scratch),
        SCR_JUMPR ^ IFTRUE (WHEN (SCR_ILG_IN)),
                -16,
        SCR_INT,
                SIR_BAD_PHASE,
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< SEL_NO_CMD >-----------------------*/,{
        /*
         *  The target does not switch to command 
         *  phase after IDENTIFY has been sent.
         *
         *  If it stays in MSG OUT phase send it 
         *  the IDENTIFY again.
         */
        SCR_JUMP ^ IFTRUE (WHEN (SCR_MSG_OUT)),
                PADDR_B (resend_ident),
        /*
         *  If target does not switch to MSG IN phase 
         *  and we sent a negotiation, assert the 
         *  failure immediately.
         */
        SCR_JUMP ^ IFTRUE (WHEN (SCR_MSG_IN)),
                PADDR_A (dispatch),
        SCR_FROM_REG (HS_REG),
                0,
        SCR_INT ^ IFTRUE (DATA (HS_NEGOTIATE)),
                SIR_NEGO_FAILED,
        /*
         *  Jump to dispatcher.
         */
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< INIT >-----------------------------*/,{
        /*
         *  Wait for the SCSI RESET signal to be 
         *  inactive before restarting operations, 
         *  since the chip may hang on SEL_ATN 
         *  if SCSI RESET is active.
         */
        SCR_FROM_REG (sstat0),
                0,
        SCR_JUMPR ^ IFTRUE (MASK (IRST, IRST)),
                -16,
        SCR_JUMP,
                PADDR_A (start),
}/*-------------------------< CLRACK >---------------------------*/,{
        /*
         *  Terminate possible pending message phase.
         */
        SCR_CLR (SCR_ACK),
                0,
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< DATAI_DONE >-----------------------*/,{
        /*
         *  Save current pointer to LASTP.
         */
        SCR_COPY (4),
                RADDR_1 (temp),
                HADDR_1 (ccb_head.lastp),
        /*
         *  If the SWIDE is not full, jump to dispatcher.
         *  We anticipate a STATUS phase.
         */
        SCR_FROM_REG (scntl2),
                0,
        SCR_JUMP ^ IFTRUE (MASK (WSR, WSR)),
                PADDR_A (datai_done_wsr),
        SCR_JUMP ^ IFTRUE (WHEN (SCR_STATUS)),
                PADDR_A (status),
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< DATAI_DONE_WSR >-------------------*/,{
        /*
         *  The SWIDE is full.
         *  Clear this condition.
         */
        SCR_REG_REG (scntl2, SCR_OR, WSR),
                0,
        /*
         *  We are expecting an IGNORE RESIDUE message 
         *  from the device, otherwise we are in data 
         *  overrun condition. Check against MSG_IN phase.
         */
        SCR_INT ^ IFFALSE (WHEN (SCR_MSG_IN)),
                SIR_SWIDE_OVERRUN,
        SCR_JUMP ^ IFFALSE (WHEN (SCR_MSG_IN)),
                PADDR_A (dispatch),
        /*
         *  We are in MSG_IN phase,
         *  Read the first byte of the message.
         *  If it is not an IGNORE RESIDUE message,
         *  signal overrun and jump to message 
         *  processing.
         */
        SCR_MOVE_ABS (1) ^ SCR_MSG_IN,
                HADDR_1 (msgin[0]),
        SCR_INT ^ IFFALSE (DATA (M_IGN_RESIDUE)),
                SIR_SWIDE_OVERRUN,
        SCR_JUMP ^ IFFALSE (DATA (M_IGN_RESIDUE)),
                PADDR_A (msg_in2),
        /*
         *  We got the message we expected.
         *  Read the 2nd byte, and jump to dispatcher.
         */
        SCR_CLR (SCR_ACK),
                0,
        SCR_MOVE_ABS (1) ^ SCR_MSG_IN,
                HADDR_1 (msgin[1]),
        SCR_CLR (SCR_ACK),
                0,
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< DATAO_DONE >-----------------------*/,{
        /*
         *  Save current pointer to LASTP.
         */
        SCR_COPY (4),
                RADDR_1 (temp),
                HADDR_1 (ccb_head.lastp),
        /*
         *  If the SODL is not full jump to dispatcher.
         *  We anticipate a STATUS phase.
         */
        SCR_FROM_REG (scntl2),
                0,
        SCR_JUMP ^ IFTRUE (MASK (WSS, WSS)),
                PADDR_A (datao_done_wss),
        SCR_JUMP ^ IFTRUE (WHEN (SCR_STATUS)),
                PADDR_A (status),
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< DATAO_DONE_WSS >-------------------*/,{
        /*
         *  The SODL is full, clear this condition.
         */
        SCR_REG_REG (scntl2, SCR_OR, WSS),
                0,
        /*
         *  And signal a DATA UNDERRUN condition 
         *  to the C code.
         */
        SCR_INT,
                SIR_SODL_UNDERRUN,
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< DATAI_PHASE >----------------------*/,{
        /*
         *  Jump to current pointer.
         */
        SCR_COPY (4),
                HADDR_1 (ccb_head.lastp),
                RADDR_1 (temp),
        SCR_RETURN,
                0,
}/*-------------------------< DATAO_PHASE >----------------------*/,{
        /*
         *  Jump to current pointer.
         */
        SCR_COPY (4),
                HADDR_1 (ccb_head.lastp),
                RADDR_1 (temp),
        SCR_RETURN,
                0,
}/*-------------------------< MSG_IN >---------------------------*/,{
        /*
         *  Get the first byte of the message.
         *
         *  The script processor doesn't negate the
         *  ACK signal after this transfer.
         */
        SCR_MOVE_ABS (1) ^ SCR_MSG_IN,
                HADDR_1 (msgin[0]),
}/*-------------------------< MSG_IN2 >--------------------------*/,{
        /*
         *  Check first against 1 byte messages 
         *  that we handle from SCRIPTS.
         */
        SCR_JUMP ^ IFTRUE (DATA (M_COMPLETE)),
                PADDR_A (complete),
        SCR_JUMP ^ IFTRUE (DATA (M_DISCONNECT)),
                PADDR_A (disconnect),
        SCR_JUMP ^ IFTRUE (DATA (M_SAVE_DP)),
                PADDR_A (save_dp),
        SCR_JUMP ^ IFTRUE (DATA (M_RESTORE_DP)),
                PADDR_A (restore_dp),
        /*
         *  We handle all other messages from the 
         *  C code, so no need to waste on-chip RAM 
         *  for those ones.
         */
        SCR_JUMP,
                PADDR_B (msg_in_etc),
}/*-------------------------< STATUS >---------------------------*/,{
        /*
         *  get the status
         */
        SCR_MOVE_ABS (1) ^ SCR_STATUS,
                HADDR_1 (scratch),
#ifdef SYM_CONF_IARB_SUPPORT
        /*
         *  If STATUS is not GOOD, clear IMMEDIATE ARBITRATION, 
         *  since we may have to tamper the start queue from 
         *  the C code.
         */
        SCR_JUMPR ^ IFTRUE (DATA (S_GOOD)),
                8,
        SCR_REG_REG (scntl1, SCR_AND, ~IARB),
                0,
#endif
        /*
         *  save status to scsi_status.
         *  mark as complete.
         */
        SCR_TO_REG (SS_REG),
                0,
        SCR_LOAD_REG (HS_REG, HS_COMPLETE),
                0,
        /*
         *  Anticipate the MESSAGE PHASE for 
         *  the TASK COMPLETE message.
         */
        SCR_JUMP ^ IFTRUE (WHEN (SCR_MSG_IN)),
                PADDR_A (msg_in),
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< COMPLETE >-------------------------*/,{
        /*
         *  Complete message.
         *
         *  When we terminate the cycle by clearing ACK,
         *  the target may disconnect immediately.
         *
         *  We don't want to be told of an "unexpected disconnect",
         *  so we disable this feature.
         */
        SCR_REG_REG (scntl2, SCR_AND, 0x7f),
                0,
        /*
         *  Terminate cycle ...
         */
        SCR_CLR (SCR_ACK|SCR_ATN),
                0,
        /*
         *  ... and wait for the disconnect.
         */
        SCR_WAIT_DISC,
                0,
}/*-------------------------< COMPLETE2 >------------------------*/,{
        /*
         *  Save host status.
         */
        SCR_COPY (4),
                RADDR_1 (scr0),
                HADDR_1 (ccb_head.status),
        /*
         *  Move back the CCB header using self-modifying 
         *  SCRIPTS.
         */
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a40),
        SCR_COPY (sizeof(struct sym_ccbh)),
                HADDR_1 (ccb_head),
}/*-------------------------< _SMS_A40 >-------------------------*/,{
                0,
        /*
         *  Some bridges may reorder DMA writes to memory.
         *  We donnot want the CPU to deal with completions  
         *  without all the posted write having been flushed 
         *  to memory. This DUMMY READ should flush posted 
         *  buffers prior to the CPU having to deal with 
         *  completions.
         */
        SCR_COPY (4),                   /* DUMMY READ */
                HADDR_1 (ccb_head.status),
                RADDR_1 (scr0),
        /*
         *  If command resulted in not GOOD status,
         *  call the C code if needed.
         */
        SCR_FROM_REG (SS_REG),
                0,
        SCR_CALL ^ IFFALSE (DATA (S_GOOD)),
                PADDR_B (bad_status),
        /*
         *  If we performed an auto-sense, call 
         *  the C code to synchronyze task aborts 
         *  with UNIT ATTENTION conditions.
         */
        SCR_FROM_REG (HF_REG),
                0,
        SCR_JUMP ^ IFFALSE (MASK (0 ,(HF_SENSE|HF_EXT_ERR))),
                PADDR_A (complete_error),
}/*-------------------------< DONE >-----------------------------*/,{
        /*
         *  Copy the DSA to the DONE QUEUE and 
         *  signal completion to the host.
         *  If we are interrupted between DONE 
         *  and DONE_END, we must reset, otherwise 
         *  the completed CCB may be lost.
         */
        SCR_COPY (4),
                PADDR_B (done_pos),
                PADDR_A (_sms_a50),
        SCR_COPY (4),
                RADDR_1 (dsa),
}/*-------------------------< _SMS_A50 >-------------------------*/,{
                0,
        SCR_COPY (4),
                PADDR_B (done_pos),
                PADDR_A (_sms_a60),
        /*
         *  The instruction below reads the DONE QUEUE next 
         *  free position from memory.
         *  In addition it ensures that all PCI posted writes  
         *  are flushed and so the DSA value of the done 
         *  CCB is visible by the CPU before INTFLY is raised.
         */
        SCR_COPY (8),
}/*-------------------------< _SMS_A60 >-------------------------*/,{
                0,
                PADDR_B (prev_done),
}/*-------------------------< DONE_END >-------------------------*/,{
        SCR_INT_FLY,
                0,
        SCR_JUMP,
                PADDR_A (start),
}/*-------------------------< COMPLETE_ERROR >-------------------*/,{
        SCR_COPY (4),
                PADDR_B (startpos),
                RADDR_1 (scratcha),
        SCR_INT,
                SIR_COMPLETE_ERROR,
}/*-------------------------< SAVE_DP >--------------------------*/,{
        /*
         *  Clear ACK immediately.
         *  No need to delay it.
         */
        SCR_CLR (SCR_ACK),
                0,
        /*
         *  Keep track we received a SAVE DP, so 
         *  we will switch to the other PM context 
         *  on the next PM since the DP may point 
         *  to the current PM context.
         */
        SCR_REG_REG (HF_REG, SCR_OR, HF_DP_SAVED),
                0,
        /*
         *  SAVE_DP message:
         *  Copy LASTP to SAVEP.
         */
        SCR_COPY (4),
                HADDR_1 (ccb_head.lastp),
                HADDR_1 (ccb_head.savep),
        /*
         *  Anticipate the MESSAGE PHASE for 
         *  the DISCONNECT message.
         */
        SCR_JUMP ^ IFTRUE (WHEN (SCR_MSG_IN)),
                PADDR_A (msg_in),
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< RESTORE_DP >-----------------------*/,{
        /*
         *  Clear ACK immediately.
         *  No need to delay it.
         */
        SCR_CLR (SCR_ACK),
                0,
        /*
         *  Copy SAVEP to LASTP.
         */
        SCR_COPY (4),
                HADDR_1 (ccb_head.savep),
                HADDR_1 (ccb_head.lastp),
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< DISCONNECT >-----------------------*/,{
        /*
         *  DISCONNECTing  ...
         *
         *  disable the "unexpected disconnect" feature,
         *  and remove the ACK signal.
         */
        SCR_REG_REG (scntl2, SCR_AND, 0x7f),
                0,
        SCR_CLR (SCR_ACK|SCR_ATN),
                0,
        /*
         *  Wait for the disconnect.
         */
        SCR_WAIT_DISC,
                0,
        /*
         *  Status is: DISCONNECTED.
         */
        SCR_LOAD_REG (HS_REG, HS_DISCONNECT),
                0,
        /*
         *  Save host status.
         */
        SCR_COPY (4),
                RADDR_1 (scr0),
                HADDR_1 (ccb_head.status),
}/*-------------------------< DISCONNECT2 >----------------------*/,{
        /*
         *  Move back the CCB header using self-modifying 
         *  SCRIPTS.
         */
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a65),
        SCR_COPY (sizeof(struct sym_ccbh)),
                HADDR_1 (ccb_head),
}/*-------------------------< _SMS_A65 >-------------------------*/,{
                0,
        SCR_JUMP,
                PADDR_A (start),
}/*-------------------------< IDLE >-----------------------------*/,{
        /*
         *  Nothing to do?
         *  Switch the LED off and wait for reselect.
         *  Will be patched with a NO_OP if LED
         *  not needed or not desired.
         */
        SCR_REG_REG (gpreg, SCR_OR, 0x01),
                0,
#ifdef SYM_CONF_IARB_SUPPORT
        SCR_JUMPR,
                8,
#endif
}/*-------------------------< UNGETJOB >-------------------------*/,{
#ifdef SYM_CONF_IARB_SUPPORT
        /*
         *  Set IMMEDIATE ARBITRATION, for the next time.
         *  This will give us better chance to win arbitration 
         *  for the job we just wanted to do.
         */
        SCR_REG_REG (scntl1, SCR_OR, IARB),
                0,
#endif
        /*
         *  We are not able to restart the SCRIPTS if we are 
         *  interrupted and these instruction haven't been 
         *  all executed. BTW, this is very unlikely to 
         *  happen, but we check that from the C code.
         */
        SCR_LOAD_REG (dsa, 0xff),
                0,
        SCR_COPY (4),
                RADDR_1 (scratcha),
                PADDR_B (startpos),
}/*-------------------------< RESELECT >-------------------------*/,{
#ifdef SYM_CONF_TARGET_ROLE_SUPPORT
        /*
         *  Make sure we are in initiator mode.
         */
        SCR_CLR (SCR_TRG),
                0,
#endif
        /*
         *  Sleep waiting for a reselection.
         */
        SCR_WAIT_RESEL,
                PADDR_A(start),
}/*-------------------------< RESELECTED >-----------------------*/,{
        /*
         *  Switch the LED on.
         *  Will be patched with a NO_OP if LED
         *  not needed or not desired.
         */
        SCR_REG_REG (gpreg, SCR_AND, 0xfe),
                0,
        /*
         *  load the target id into the sdid
         */
        SCR_REG_SFBR (ssid, SCR_AND, 0x8F),
                0,
        SCR_TO_REG (sdid),
                0,
        /*
         *  Load the target control block address
         */
        SCR_COPY (4),
                PADDR_B (targtbl),
                RADDR_1 (dsa),
        SCR_SFBR_REG (dsa, SCR_SHL, 0),
                0,
        SCR_REG_REG (dsa, SCR_SHL, 0),
                0,
        SCR_REG_REG (dsa, SCR_AND, 0x3c),
                0,
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a70),
        SCR_COPY (4),
}/*-------------------------< _SMS_A70 >-------------------------*/,{
                0,
                RADDR_1 (dsa),
        /*
         *  Copy the TCB header to a fixed place in 
         *  the HCB.
         */
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a80),
        SCR_COPY (sizeof(struct sym_tcbh)),
}/*-------------------------< _SMS_A80 >-------------------------*/,{
                0,
                HADDR_1 (tcb_head),
        /*
         *  We expect MESSAGE IN phase.
         *  If not, get help from the C code.
         */
        SCR_INT ^ IFFALSE (WHEN (SCR_MSG_IN)),
                SIR_RESEL_NO_MSG_IN,
}/*-------------------------< RESELECTED1 >----------------------*/,{
        /*
         *  Load the synchronous transfer registers.
         */
        SCR_COPY (1),
                HADDR_1 (tcb_head.wval),
                RADDR_1 (scntl3),
        SCR_COPY (1),
                HADDR_1 (tcb_head.sval),
                RADDR_1 (sxfer),
        /*
         *  Get the IDENTIFY message.
         */
        SCR_MOVE_ABS (1) ^ SCR_MSG_IN,
                HADDR_1 (msgin),
        /*
         *  If IDENTIFY LUN #0, use a faster path 
         *  to find the LCB structure.
         */
        SCR_JUMP ^ IFTRUE (MASK (0x80, 0xbf)),
                PADDR_A (resel_lun0),
        /*
         *  If message isn't an IDENTIFY, 
         *  tell the C code about.
         */
        SCR_INT ^ IFFALSE (MASK (0x80, 0x80)),
                SIR_RESEL_NO_IDENTIFY,
        /*
         *  It is an IDENTIFY message,
         *  Load the LUN control block address.
         */
        SCR_COPY (4),
                HADDR_1 (tcb_head.luntbl_sa),
                RADDR_1 (dsa),
        SCR_SFBR_REG (dsa, SCR_SHL, 0),
                0,
        SCR_REG_REG (dsa, SCR_SHL, 0),
                0,
        SCR_REG_REG (dsa, SCR_AND, 0xfc),
                0,
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a90),
        SCR_COPY (4),
}/*-------------------------< _SMS_A90 >-------------------------*/,{
                0,
                RADDR_1 (dsa),
        SCR_JUMPR,
                12,
}/*-------------------------< RESEL_LUN0 >-----------------------*/,{
        /*
         *  LUN 0 special case (but usual one :))
         */
        SCR_COPY (4),
                HADDR_1 (tcb_head.lun0_sa),
                RADDR_1 (dsa),
        /*
         *  Jump indirectly to the reselect action for this LUN.
         *  (lcb.head.resel_sa assumed at offset zero of lcb).
         */
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a100),
        SCR_COPY (4),
}/*-------------------------< _SMS_A100 >------------------------*/,{
                0,
                RADDR_1 (temp),
        SCR_RETURN,
                0,
        /* In normal situations, we jump to RESEL_TAG or RESEL_NO_TAG */
}/*-------------------------< RESEL_TAG >------------------------*/,{

        /*
         *  ACK the IDENTIFY previously received.
         */
        SCR_CLR (SCR_ACK),
                0,
        /*
         *  It shall be a tagged command.
         *  Read SIMPLE+TAG.
         *  The C code will deal with errors.
         *  Aggressive optimization, isn't it? :)
         */
        SCR_MOVE_ABS (2) ^ SCR_MSG_IN,
                HADDR_1 (msgin),
        /*
         *  Copy the LCB header to a fixed place in 
         *  the HCB using self-modifying SCRIPTS.
         */
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a110),
        SCR_COPY (sizeof(struct sym_lcbh)),
}/*-------------------------< _SMS_A110 >------------------------*/,{
                0,
                HADDR_1 (lcb_head),
        /*
         *  Load the pointer to the tagged task 
         *  table for this LUN.
         */
        SCR_COPY (4),
                HADDR_1 (lcb_head.itlq_tbl_sa),
                RADDR_1 (dsa),
        /*
         *  The SIDL still contains the TAG value.
         *  Aggressive optimization, isn't it? :):)
         */
        SCR_REG_SFBR (sidl, SCR_SHL, 0),
                0,
#if SYM_CONF_MAX_TASK*4 > 512
        SCR_JUMPR ^ IFFALSE (CARRYSET),
                8,
        SCR_REG_REG (dsa1, SCR_OR, 2),
                0,
        SCR_REG_REG (sfbr, SCR_SHL, 0),
                0,
        SCR_JUMPR ^ IFFALSE (CARRYSET),
                8,
        SCR_REG_REG (dsa1, SCR_OR, 1),
                0,
#elif SYM_CONF_MAX_TASK*4 > 256
        SCR_JUMPR ^ IFFALSE (CARRYSET),
                8,
        SCR_REG_REG (dsa1, SCR_OR, 1),
                0,
#endif
        /*
         *  Retrieve the DSA of this task.
         *  JUMP indirectly to the restart point of the CCB.
         */
        SCR_SFBR_REG (dsa, SCR_AND, 0xfc),
                0,
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a120),
        SCR_COPY (4),
}/*-------------------------< _SMS_A120 >------------------------*/,{
                0,
                RADDR_1 (dsa),
}/*-------------------------< RESEL_GO >-------------------------*/,{
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a130),
        /*
         *  Move 'ccb.phys.head.go' action to 
         *  scratch/scratch1. So scratch1 will 
         *  contain the 'restart' field of the 
         *  'go' structure.
         */
        SCR_COPY (8),
}/*-------------------------< _SMS_A130 >------------------------*/,{
                0,
                PADDR_B (scratch),
        SCR_COPY (4),
                PADDR_B (scratch1), /* phys.head.go.restart */
                RADDR_1 (temp),
        SCR_RETURN,
                0,
        /* In normal situations we branch to RESEL_DSA */
}/*-------------------------< RESEL_DSA >------------------------*/,{
        /*
         *  ACK the IDENTIFY or TAG previously received.
         */
        SCR_CLR (SCR_ACK),
                0,
}/*-------------------------< RESEL_DSA1 >-----------------------*/,{
        /*
         *  Copy the CCB header to a fixed location 
         *  in the HCB using self-modifying SCRIPTS.
         */
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a140),
        SCR_COPY (sizeof(struct sym_ccbh)),
}/*-------------------------< _SMS_A140 >------------------------*/,{
                0,
                HADDR_1 (ccb_head),
        /*
         *  Initialize the status register
         */
        SCR_COPY (4),
                HADDR_1 (ccb_head.status),
                RADDR_1 (scr0),
        /*
         *  Jump to dispatcher.
         */
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< RESEL_NO_TAG >---------------------*/,{
        /*
         *  Copy the LCB header to a fixed place in 
         *  the HCB using self-modifying SCRIPTS.
         */
        SCR_COPY (4),
                RADDR_1 (dsa),
                PADDR_A (_sms_a145),
        SCR_COPY (sizeof(struct sym_lcbh)),
}/*-------------------------< _SMS_A145 >------------------------*/,{
                0,
                HADDR_1 (lcb_head),
        /*
         *  Load the DSA with the unique ITL task.
         */
        SCR_COPY (4),
                HADDR_1 (lcb_head.itl_task_sa),
                RADDR_1 (dsa),
        SCR_JUMP,
                PADDR_A (resel_go),
}/*-------------------------< DATA_IN >--------------------------*/,{
/*
 *  Because the size depends on the
 *  #define SYM_CONF_MAX_SG parameter,
 *  it is filled in at runtime.
 *
 *  ##===========< i=0; i<SYM_CONF_MAX_SG >=========
 *  ||  SCR_CHMOV_TBL ^ SCR_DATA_IN,
 *  ||          offsetof (struct sym_dsb, data[ i]),
 *  ##==========================================
 */
0
}/*-------------------------< DATA_IN2 >-------------------------*/,{
        SCR_CALL,
                PADDR_A (datai_done),
        SCR_JUMP,
                PADDR_B (data_ovrun),
}/*-------------------------< DATA_OUT >-------------------------*/,{
/*
 *  Because the size depends on the
 *  #define SYM_CONF_MAX_SG parameter,
 *  it is filled in at runtime.
 *
 *  ##===========< i=0; i<SYM_CONF_MAX_SG >=========
 *  ||  SCR_CHMOV_TBL ^ SCR_DATA_OUT,
 *  ||          offsetof (struct sym_dsb, data[ i]),
 *  ##==========================================
 */
0
}/*-------------------------< DATA_OUT2 >------------------------*/,{
        SCR_CALL,
                PADDR_A (datao_done),
        SCR_JUMP,
                PADDR_B (data_ovrun),
}/*-------------------------< PM0_DATA >-------------------------*/,{
        /*
         *  Read our host flags to SFBR, so we will be able 
         *  to check against the data direction we expect.
         */
        SCR_FROM_REG (HF_REG),
                0,
        /*
         *  Check against actual DATA PHASE.
         */
        SCR_JUMP ^ IFFALSE (WHEN (SCR_DATA_IN)),
                PADDR_A (pm0_data_out),
        /*
         *  Actual phase is DATA IN.
         *  Check against expected direction.
         */
        SCR_JUMP ^ IFFALSE (MASK (HF_DATA_IN, HF_DATA_IN)),
                PADDR_B (data_ovrun),
        /*
         *  Keep track we are moving data from the 
         *  PM0 DATA mini-script.
         */
        SCR_REG_REG (HF_REG, SCR_OR, HF_IN_PM0),
                0,
        /*
         *  Move the data to memory.
         */
        SCR_CHMOV_TBL ^ SCR_DATA_IN,
                offsetof (struct sym_ccb, phys.pm0.sg),
        SCR_JUMP,
                PADDR_A (pm0_data_end),
}/*-------------------------< PM0_DATA_OUT >---------------------*/,{
        /*
         *  Actual phase is DATA OUT.
         *  Check against expected direction.
         */
        SCR_JUMP ^ IFTRUE (MASK (HF_DATA_IN, HF_DATA_IN)),
                PADDR_B (data_ovrun),
        /*
         *  Keep track we are moving data from the 
         *  PM0 DATA mini-script.
         */
        SCR_REG_REG (HF_REG, SCR_OR, HF_IN_PM0),
                0,
        /*
         *  Move the data from memory.
         */
        SCR_CHMOV_TBL ^ SCR_DATA_OUT,
                offsetof (struct sym_ccb, phys.pm0.sg),
}/*-------------------------< PM0_DATA_END >---------------------*/,{
        /*
         *  Clear the flag that told we were moving  
         *  data from the PM0 DATA mini-script.
         */
        SCR_REG_REG (HF_REG, SCR_AND, (~HF_IN_PM0)),
                0,
        /*
         *  Return to the previous DATA script which 
         *  is guaranteed by design (if no bug) to be 
         *  the main DATA script for this transfer.
         */
        SCR_COPY (4),
                RADDR_1 (dsa),
                RADDR_1 (scratcha),
        SCR_REG_REG (scratcha, SCR_ADD, offsetof (struct sym_ccb,phys.pm0.ret)),
                0,
}/*-------------------------< PM_DATA_END >----------------------*/,{
        SCR_COPY (4),
                RADDR_1 (scratcha),
                PADDR_A (_sms_a150),
        SCR_COPY (4),
}/*-------------------------< _SMS_A150 >------------------------*/,{
                0,
                RADDR_1 (temp),
        SCR_RETURN,
                0,
}/*-------------------------< PM1_DATA >-------------------------*/,{
        /*
         *  Read our host flags to SFBR, so we will be able 
         *  to check against the data direction we expect.
         */
        SCR_FROM_REG (HF_REG),
                0,
        /*
         *  Check against actual DATA PHASE.
         */
        SCR_JUMP ^ IFFALSE (WHEN (SCR_DATA_IN)),
                PADDR_A (pm1_data_out),
        /*
         *  Actual phase is DATA IN.
         *  Check against expected direction.
         */
        SCR_JUMP ^ IFFALSE (MASK (HF_DATA_IN, HF_DATA_IN)),
                PADDR_B (data_ovrun),
        /*
         *  Keep track we are moving data from the 
         *  PM1 DATA mini-script.
         */
        SCR_REG_REG (HF_REG, SCR_OR, HF_IN_PM1),
                0,
        /*
         *  Move the data to memory.
         */
        SCR_CHMOV_TBL ^ SCR_DATA_IN,
                offsetof (struct sym_ccb, phys.pm1.sg),
        SCR_JUMP,
                PADDR_A (pm1_data_end),
}/*-------------------------< PM1_DATA_OUT >---------------------*/,{
        /*
         *  Actual phase is DATA OUT.
         *  Check against expected direction.
         */
        SCR_JUMP ^ IFTRUE (MASK (HF_DATA_IN, HF_DATA_IN)),
                PADDR_B (data_ovrun),
        /*
         *  Keep track we are moving data from the 
         *  PM1 DATA mini-script.
         */
        SCR_REG_REG (HF_REG, SCR_OR, HF_IN_PM1),
                0,
        /*
         *  Move the data from memory.
         */
        SCR_CHMOV_TBL ^ SCR_DATA_OUT,
                offsetof (struct sym_ccb, phys.pm1.sg),
}/*-------------------------< PM1_DATA_END >---------------------*/,{
        /*
         *  Clear the flag that told we were moving  
         *  data from the PM1 DATA mini-script.
         */
        SCR_REG_REG (HF_REG, SCR_AND, (~HF_IN_PM1)),
                0,
        /*
         *  Return to the previous DATA script which 
         *  is guaranteed by design (if no bug) to be 
         *  the main DATA script for this transfer.
         */
        SCR_COPY (4),
                RADDR_1 (dsa),
                RADDR_1 (scratcha),
        SCR_REG_REG (scratcha, SCR_ADD, offsetof (struct sym_ccb,phys.pm1.ret)),
                0,
        SCR_JUMP,
                PADDR_A (pm_data_end),
}/*--------------------------<>----------------------------------*/
};

static struct SYM_FWB_SCR SYM_FWB_SCR = {
/*-------------------------< NO_DATA >--------------------------*/ {
        SCR_JUMP,
                PADDR_B (data_ovrun),
}/*-------------------------< SEL_FOR_ABORT >--------------------*/,{
        /*
         *  We are jumped here by the C code, if we have 
         *  some target to reset or some disconnected 
         *  job to abort. Since error recovery is a serious 
         *  busyness, we will really reset the SCSI BUS, if 
         *  case of a SCSI interrupt occurring in this path.
         */

#ifdef SYM_CONF_TARGET_ROLE_SUPPORT
        /*
         *  Set initiator mode.
         */
        SCR_CLR (SCR_TRG),
                0,
#endif
        /*
         *      And try to select this target.
         */
        SCR_SEL_TBL_ATN ^ offsetof (struct sym_hcb, abrt_sel),
                PADDR_A (reselect),
        /*
         *  Wait for the selection to complete or 
         *  the selection to time out.
         */
        SCR_JUMPR ^ IFFALSE (WHEN (SCR_MSG_OUT)),
                -8,
        /*
         *  Call the C code.
         */
        SCR_INT,
                SIR_TARGET_SELECTED,
        /*
         *  The C code should let us continue here. 
         *  Send the 'kiss of death' message.
         *  We expect an immediate disconnect once 
         *  the target has eaten the message.
         */
        SCR_REG_REG (scntl2, SCR_AND, 0x7f),
                0,
        SCR_MOVE_TBL ^ SCR_MSG_OUT,
                offsetof (struct sym_hcb, abrt_tbl),
        SCR_CLR (SCR_ACK|SCR_ATN),
                0,
        SCR_WAIT_DISC,
                0,
        /*
         *  Tell the C code that we are done.
         */
        SCR_INT,
                SIR_ABORT_SENT,
}/*-------------------------< SEL_FOR_ABORT_1 >------------------*/,{
        /*
         *  Jump at scheduler.
         */
        SCR_JUMP,
                PADDR_A (start),
}/*-------------------------< MSG_IN_ETC >-----------------------*/,{
        /*
         *  If it is an EXTENDED (variable size message)
         *  Handle it.
         */
        SCR_JUMP ^ IFTRUE (DATA (M_EXTENDED)),
                PADDR_B (msg_extended),
        /*
         *  Let the C code handle any other 
         *  1 byte message.
         */
        SCR_JUMP ^ IFTRUE (MASK (0x00, 0xf0)),
                PADDR_B (msg_received),
        SCR_JUMP ^ IFTRUE (MASK (0x10, 0xf0)),
                PADDR_B (msg_received),
        /*
         *  We donnot handle 2 bytes messages from SCRIPTS.
         *  So, let the C code deal with these ones too.
         */
        SCR_JUMP ^ IFFALSE (MASK (0x20, 0xf0)),
                PADDR_B (msg_weird_seen),
        SCR_CLR (SCR_ACK),
                0,
        SCR_MOVE_ABS (1) ^ SCR_MSG_IN,
                HADDR_1 (msgin[1]),
}/*-------------------------< MSG_RECEIVED >---------------------*/,{
        SCR_COPY (4),                   /* DUMMY READ */
                HADDR_1 (scratch),
                RADDR_1 (scratcha),
        SCR_INT,
                SIR_MSG_RECEIVED,
}/*-------------------------< MSG_WEIRD_SEEN >-------------------*/,{
        SCR_COPY (4),                   /* DUMMY READ */
                HADDR_1 (scratch),
                RADDR_1 (scratcha),
        SCR_INT,
                SIR_MSG_WEIRD,
}/*-------------------------< MSG_EXTENDED >---------------------*/,{
        /*
         *  Clear ACK and get the next byte 
         *  assumed to be the message length.
         */
        SCR_CLR (SCR_ACK),
                0,
        SCR_MOVE_ABS (1) ^ SCR_MSG_IN,
                HADDR_1 (msgin[1]),
        /*
         *  Try to catch some unlikely situations as 0 length 
         *  or too large the length.
         */
        SCR_JUMP ^ IFTRUE (DATA (0)),
                PADDR_B (msg_weird_seen),
        SCR_TO_REG (scratcha),
                0,
        SCR_REG_REG (sfbr, SCR_ADD, (256-8)),
                0,
        SCR_JUMP ^ IFTRUE (CARRYSET),
                PADDR_B (msg_weird_seen),
        /*
         *  We donnot handle extended messages from SCRIPTS.
         *  Read the amount of data corresponding to the 
         *  message length and call the C code.
         */
        SCR_COPY (1),
                RADDR_1 (scratcha),
                PADDR_B (_sms_b10),
        SCR_CLR (SCR_ACK),
                0,
}/*-------------------------< _SMS_B10 >-------------------------*/,{
        SCR_MOVE_ABS (0) ^ SCR_MSG_IN,
                HADDR_1 (msgin[2]),
        SCR_JUMP,
                PADDR_B (msg_received),
}/*-------------------------< MSG_BAD >--------------------------*/,{
        /*
         *  unimplemented message - reject it.
         */
        SCR_INT,
                SIR_REJECT_TO_SEND,
        SCR_SET (SCR_ATN),
                0,
        SCR_JUMP,
                PADDR_A (clrack),
}/*-------------------------< MSG_WEIRD >------------------------*/,{
        /*
         *  weird message received
         *  ignore all MSG IN phases and reject it.
         */
        SCR_INT,
                SIR_REJECT_TO_SEND,
        SCR_SET (SCR_ATN),
                0,
}/*-------------------------< MSG_WEIRD1 >-----------------------*/,{
        SCR_CLR (SCR_ACK),
                0,
        SCR_JUMP ^ IFFALSE (WHEN (SCR_MSG_IN)),
                PADDR_A (dispatch),
        SCR_MOVE_ABS (1) ^ SCR_MSG_IN,
                HADDR_1 (scratch),
        SCR_JUMP,
                PADDR_B (msg_weird1),
}/*-------------------------< WDTR_RESP >------------------------*/,{
        /*
         *  let the target fetch our answer.
         */
        SCR_SET (SCR_ATN),
                0,
        SCR_CLR (SCR_ACK),
                0,
        SCR_JUMP ^ IFFALSE (WHEN (SCR_MSG_OUT)),
                PADDR_B (nego_bad_phase),
}/*-------------------------< SEND_WDTR >------------------------*/,{
        /*
         *  Send the M_X_WIDE_REQ
         */
        SCR_MOVE_ABS (4) ^ SCR_MSG_OUT,
                HADDR_1 (msgout),
        SCR_JUMP,
                PADDR_B (msg_out_done),
}/*-------------------------< SDTR_RESP >------------------------*/,{
        /*
         *  let the target fetch our answer.
         */
        SCR_SET (SCR_ATN),
                0,
        SCR_CLR (SCR_ACK),
                0,
        SCR_JUMP ^ IFFALSE (WHEN (SCR_MSG_OUT)),
                PADDR_B (nego_bad_phase),
}/*-------------------------< SEND_SDTR >------------------------*/,{
        /*
         *  Send the M_X_SYNC_REQ
         */
        SCR_MOVE_ABS (5) ^ SCR_MSG_OUT,
                HADDR_1 (msgout),
        SCR_JUMP,
                PADDR_B (msg_out_done),
}/*-------------------------< PPR_RESP >-------------------------*/,{
        /*
         *  let the target fetch our answer.
         */
        SCR_SET (SCR_ATN),
                0,
        SCR_CLR (SCR_ACK),
                0,
        SCR_JUMP ^ IFFALSE (WHEN (SCR_MSG_OUT)),
                PADDR_B (nego_bad_phase),
}/*-------------------------< SEND_PPR >-------------------------*/,{
        /*
         *  Send the M_X_PPR_REQ
         */
        SCR_MOVE_ABS (8) ^ SCR_MSG_OUT,
                HADDR_1 (msgout),
        SCR_JUMP,
                PADDR_B (msg_out_done),
}/*-------------------------< NEGO_BAD_PHASE >-------------------*/,{
        SCR_INT,
                SIR_NEGO_PROTO,
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< MSG_OUT >--------------------------*/,{
        /*
         *  The target requests a message.
         *  We donnot send messages that may 
         *  require the device to go to bus free.
         */
        SCR_MOVE_ABS (1) ^ SCR_MSG_OUT,
                HADDR_1 (msgout),
        /*
         *  ... wait for the next phase
         *  if it's a message out, send it again, ...
         */
        SCR_JUMP ^ IFTRUE (WHEN (SCR_MSG_OUT)),
                PADDR_B (msg_out),
}/*-------------------------< MSG_OUT_DONE >---------------------*/,{
        /*
         *  Let the C code be aware of the 
         *  sent message and clear the message.
         */
        SCR_INT,
                SIR_MSG_OUT_DONE,
        /*
         *  ... and process the next phase
         */
        SCR_JUMP,
                PADDR_A (dispatch),
}/*-------------------------< DATA_OVRUN >-----------------------*/,{
        /*
         *  Zero scratcha that will count the 
         *  extras bytes.
         */
        SCR_COPY (4),
                PADDR_B (zero),
                RADDR_1 (scratcha),
}/*-------------------------< DATA_OVRUN1 >----------------------*/,{
        /*
         *  The target may want to transfer too much data.
         *
         *  If phase is DATA OUT write 1 byte and count it.
         */
        SCR_JUMPR ^ IFFALSE (WHEN (SCR_DATA_OUT)),
                16,
        SCR_CHMOV_ABS (1) ^ SCR_DATA_OUT,
                HADDR_1 (scratch),
        SCR_JUMP,
                PADDR_B (data_ovrun2),
        /*
         *  If WSR is set, clear this condition, and 
         *  count this byte.
         */
        SCR_FROM_REG (scntl2),
                0,
        SCR_JUMPR ^ IFFALSE (MASK (WSR, WSR)),
                16,
        SCR_REG_REG (scntl2, SCR_OR, WSR),
                0,
        SCR_JUMP,
                PADDR_B (data_ovrun2),
        /*
         *  Finally check against DATA IN phase.
         *  Signal data overrun to the C code 
         *  and jump to dispatcher if not so.
         *  Read 1 byte otherwise and count it.
         */
        SCR_JUMPR ^ IFTRUE (WHEN (SCR_DATA_IN)),
                16,
        SCR_INT,
                SIR_DATA_OVERRUN,
        SCR_JUMP,
                PADDR_A (dispatch),
        SCR_CHMOV_ABS (1) ^ SCR_DATA_IN,
                HADDR_1 (scratch),
}/*-------------------------< DATA_OVRUN2 >----------------------*/,{
        /*
         *  Count this byte.
         *  This will allow to return a negative 
         *  residual to user.
         */
        SCR_REG_REG (scratcha,  SCR_ADD,  0x01),
                0,
        SCR_REG_REG (scratcha1, SCR_ADDC, 0),
                0,
        SCR_REG_REG (scratcha2, SCR_ADDC, 0),
                0,
        /*
         *  .. and repeat as required.
         */
        SCR_JUMP,
                PADDR_B (data_ovrun1),
}/*-------------------------< ABORT_RESEL >----------------------*/,{
        SCR_SET (SCR_ATN),
                0,
        SCR_CLR (SCR_ACK),
                0,
        /*
         *  send the abort/abortag/reset message
         *  we expect an immediate disconnect
         */
        SCR_REG_REG (scntl2, SCR_AND, 0x7f),
                0,
        SCR_MOVE_ABS (1) ^ SCR_MSG_OUT,
                HADDR_1 (msgout),
        SCR_CLR (SCR_ACK|SCR_ATN),
                0,
        SCR_WAIT_DISC,
                0,
        SCR_INT,
                SIR_RESEL_ABORTED,
        SCR_JUMP,
                PADDR_A (start),
}/*-------------------------< RESEND_IDENT >---------------------*/,{
        /*
         *  The target stays in MSG OUT phase after having acked 
         *  Identify [+ Tag [+ Extended message ]]. Targets shall
         *  behave this way on parity error.
         *  We must send it again all the messages.
         */
        SCR_SET (SCR_ATN), /* Shall be asserted 2 deskew delays before the  */
                0,         /* 1rst ACK = 90 ns. Hope the chip isn't too fast */
        SCR_JUMP,
                PADDR_A (send_ident),
}/*-------------------------< IDENT_BREAK >----------------------*/,{
        SCR_CLR (SCR_ATN),
                0,
        SCR_JUMP,
                PADDR_A (select2),
}/*-------------------------< IDENT_BREAK_ATN >------------------*/,{
        SCR_SET (SCR_ATN),
                0,
        SCR_JUMP,
                PADDR_A (select2),
}/*-------------------------< SDATA_IN >-------------------------*/,{
        SCR_CHMOV_TBL ^ SCR_DATA_IN,
                offsetof (struct sym_dsb, sense),
        SCR_CALL,
                PADDR_A (datai_done),
        SCR_JUMP,
                PADDR_B (data_ovrun),
}/*-------------------------< RESEL_BAD_LUN >--------------------*/,{
        /*
         *  Message is an IDENTIFY, but lun is unknown.
         *  Signal problem to C code for logging the event.
         *  Send a M_ABORT to clear all pending tasks.
         */
        SCR_INT,
                SIR_RESEL_BAD_LUN,
        SCR_JUMP,
                PADDR_B (abort_resel),
}/*-------------------------< BAD_I_T_L >------------------------*/,{
        /*
         *  We donnot have a task for that I_T_L.
         *  Signal problem to C code for logging the event.
         *  Send a M_ABORT message.
         */
        SCR_INT,
                SIR_RESEL_BAD_I_T_L,
        SCR_JUMP,
                PADDR_B (abort_resel),
}/*-------------------------< BAD_I_T_L_Q >----------------------*/,{
        /*
         *  We donnot have a task that matches the tag.
         *  Signal problem to C code for logging the event.
         *  Send a M_ABORTTAG message.
         */
        SCR_INT,
                SIR_RESEL_BAD_I_T_L_Q,
        SCR_JUMP,
                PADDR_B (abort_resel),
}/*-------------------------< BAD_STATUS >-----------------------*/,{
        /*
         *  Anything different from INTERMEDIATE 
         *  CONDITION MET should be a bad SCSI status, 
         *  given that GOOD status has already been tested.
         *  Call the C code.
         */
        SCR_COPY (4),
                PADDR_B (startpos),
                RADDR_1 (scratcha),
        SCR_INT ^ IFFALSE (DATA (S_COND_MET)),
                SIR_BAD_SCSI_STATUS,
        SCR_RETURN,
                0,
}/*-------------------------< WSR_MA_HELPER >--------------------*/,{
        /*
         *  Helper for the C code when WSR bit is set.
         *  Perform the move of the residual byte.
         */
        SCR_CHMOV_TBL ^ SCR_DATA_IN,
                offsetof (struct sym_ccb, phys.wresid),
        SCR_JUMP,
                PADDR_A (dispatch),

}/*-------------------------< ZERO >-----------------------------*/,{
        SCR_DATA_ZERO,
}/*-------------------------< SCRATCH >--------------------------*/,{
        SCR_DATA_ZERO, /* MUST BE BEFORE SCRATCH1 */
}/*-------------------------< SCRATCH1 >-------------------------*/,{
        SCR_DATA_ZERO,
}/*-------------------------< PREV_DONE >------------------------*/,{
        SCR_DATA_ZERO, /* MUST BE BEFORE DONE_POS ! */
}/*-------------------------< DONE_POS >-------------------------*/,{
        SCR_DATA_ZERO,
}/*-------------------------< NEXTJOB >--------------------------*/,{
        SCR_DATA_ZERO, /* MUST BE BEFORE STARTPOS ! */
}/*-------------------------< STARTPOS >-------------------------*/,{
        SCR_DATA_ZERO,
}/*-------------------------< TARGTBL >--------------------------*/,{
        SCR_DATA_ZERO,
}/*--------------------------<>----------------------------------*/
};

static struct SYM_FWZ_SCR SYM_FWZ_SCR = {
 /*-------------------------< SNOOPTEST >------------------------*/{
        /*
         *  Read the variable.
         */
        SCR_COPY (4),
                HADDR_1 (scratch),
                RADDR_1 (scratcha),
        /*
         *  Write the variable.
         */
        SCR_COPY (4),
                RADDR_1 (temp),
                HADDR_1 (scratch),
        /*
         *  Read back the variable.
         */
        SCR_COPY (4),
                HADDR_1 (scratch),
                RADDR_1 (temp),
}/*-------------------------< SNOOPEND >-------------------------*/,{
        /*
         *  And stop.
         */
        SCR_INT,
                99,
}/*--------------------------<>----------------------------------*/
};