/* stnic.c : A SH7750 specific part of driver for NS DP83902A ST-NIC.
 *
 * This file is subject to the terms and conditions of the GNU General Public
 * License.  See the file "COPYING" in the main directory of this archive
 * for more details.
 *
 * Copyright (C) 1999 kaz Kojima
 */

#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/init.h>
#include <linux/delay.h>

#include <asm/io.h>
#include <mach-se/mach/se.h>
#include <asm/machvec.h>
#ifdef CONFIG_SH_STANDARD_BIOS
#include <asm/sh_bios.h>
#endif

#include "8390.h"

#define DRV_NAME "stnic"

#define byte    unsigned char
#define half    unsigned short
#define word    unsigned int
#define vbyte   volatile unsigned char
#define vhalf   volatile unsigned short
#define vword   volatile unsigned int

#define STNIC_RUN       0x01    /* 1 == Run, 0 == reset. */

#define START_PG        0       /* First page of TX buffer */
#define STOP_PG         128     /* Last page +1 of RX ring */

/* Alias */
#define STNIC_CR        E8390_CMD
#define PG0_RSAR0       EN0_RSARLO
#define PG0_RSAR1       EN0_RSARHI
#define PG0_RBCR0       EN0_RCNTLO
#define PG0_RBCR1       EN0_RCNTHI

#define CR_RRD          E8390_RREAD
#define CR_RWR          E8390_RWRITE
#define CR_PG0          E8390_PAGE0
#define CR_STA          E8390_START
#define CR_RDMA         E8390_NODMA

/* FIXME! YOU MUST SET YOUR OWN ETHER ADDRESS.  */
static byte stnic_eadr[6] =
{0x00, 0xc0, 0x6e, 0x00, 0x00, 0x07};

static struct net_device *stnic_dev;

static void stnic_reset (struct net_device *dev);
static void stnic_get_hdr (struct net_device *dev, struct e8390_pkt_hdr *hdr,
                           int ring_page);
static void stnic_block_input (struct net_device *dev, int count,
                               struct sk_buff *skb , int ring_offset);
static void stnic_block_output (struct net_device *dev, int count,
                                const unsigned char *buf, int start_page);

static void stnic_init (struct net_device *dev);

static u32 stnic_msg_enable;

module_param_named(msg_enable, stnic_msg_enable, uint, 0444);
MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)");

/* SH7750 specific read/write io. */
static inline void
STNIC_DELAY (void)
{
  vword trash;
  trash = *(vword *) 0xa0000000;
  trash = *(vword *) 0xa0000000;
  trash = *(vword *) 0xa0000000;
}

static inline byte
STNIC_READ (int reg)
{
  byte val;

  val = (*(vhalf *) (PA_83902 + ((reg) << 1)) >> 8) & 0xff;
  STNIC_DELAY ();
  return val;
}

static inline void
STNIC_WRITE (int reg, byte val)
{
  *(vhalf *) (PA_83902 + ((reg) << 1)) = ((half) (val) << 8);
  STNIC_DELAY ();
}

static int __init stnic_probe(void)
{
  struct net_device *dev;
  int i, err;
  struct ei_device *ei_local;

  /* If we are not running on a SolutionEngine, give up now */
  if (! MACH_SE)
    return -ENODEV;

  /* New style probing API */
  dev = alloc_ei_netdev();
  if (!dev)
        return -ENOMEM;

#ifdef CONFIG_SH_STANDARD_BIOS
  sh_bios_get_node_addr (stnic_eadr);
#endif
  for (i = 0; i < ETH_ALEN; i++)
    dev->dev_addr[i] = stnic_eadr[i];

  /* Set the base address to point to the NIC, not the "real" base! */
  dev->base_addr = 0x1000;
  dev->irq = IRQ_STNIC;
  dev->netdev_ops = &ei_netdev_ops;

  /* Snarf the interrupt now.  There's no point in waiting since we cannot
     share and the board will usually be enabled. */
  err = request_irq (dev->irq, ei_interrupt, 0, DRV_NAME, dev);
  if (err)  {
        netdev_emerg(dev, " unable to get IRQ %d.\n", dev->irq);
        free_netdev(dev);
        return err;
  }

  ei_status.name = dev->name;
  ei_status.word16 = 1;
#ifdef __LITTLE_ENDIAN__
  ei_status.bigendian = 0;
#else
  ei_status.bigendian = 1;
#endif
  ei_status.tx_start_page = START_PG;
  ei_status.rx_start_page = START_PG + TX_PAGES;
  ei_status.stop_page = STOP_PG;

  ei_status.reset_8390 = &stnic_reset;
  ei_status.get_8390_hdr = &stnic_get_hdr;
  ei_status.block_input = &stnic_block_input;
  ei_status.block_output = &stnic_block_output;

  stnic_init (dev);
  ei_local = netdev_priv(dev);
  ei_local->msg_enable = stnic_msg_enable;

  err = register_netdev(dev);
  if (err) {
    free_irq(dev->irq, dev);
    free_netdev(dev);
    return err;
  }
  stnic_dev = dev;

  netdev_info(dev, "NS ST-NIC 83902A\n");

  return 0;
}

static void
stnic_reset (struct net_device *dev)
{
  struct ei_device *ei_local = netdev_priv(dev);

  *(vhalf *) PA_83902_RST = 0;
  udelay (5);
  netif_warn(ei_local, hw, dev, "8390 reset done (%ld).\n", jiffies);
  *(vhalf *) PA_83902_RST = ~0;
  udelay (5);
}

static void
stnic_get_hdr (struct net_device *dev, struct e8390_pkt_hdr *hdr,
               int ring_page)
{
  struct ei_device *ei_local = netdev_priv(dev);

  half buf[2];

  STNIC_WRITE (PG0_RSAR0, 0);
  STNIC_WRITE (PG0_RSAR1, ring_page);
  STNIC_WRITE (PG0_RBCR0, 4);
  STNIC_WRITE (PG0_RBCR1, 0);
  STNIC_WRITE (STNIC_CR, CR_RRD | CR_PG0 | CR_STA);

  buf[0] = *(vhalf *) PA_83902_IF;
  STNIC_DELAY ();
  buf[1] = *(vhalf *) PA_83902_IF;
  STNIC_DELAY ();
  hdr->next = buf[0] >> 8;
  hdr->status = buf[0] & 0xff;
#ifdef __LITTLE_ENDIAN__
  hdr->count = buf[1];
#else
  hdr->count = ((buf[1] >> 8) & 0xff) | (buf[1] << 8);
#endif

  netif_dbg(ei_local, probe, dev, "ring %x status %02x next %02x count %04x.\n",
            ring_page, hdr->status, hdr->next, hdr->count);

  STNIC_WRITE (STNIC_CR, CR_RDMA | CR_PG0 | CR_STA);
}

/* Block input and output, similar to the Crynwr packet driver. If you are
   porting to a new ethercard look at the packet driver source for hints.
   The HP LAN doesn't use shared memory -- we put the packet
   out through the "remote DMA" dataport. */

static void
stnic_block_input (struct net_device *dev, int length, struct sk_buff *skb,
                   int offset)
{
  char *buf = skb->data;
  half val;

  STNIC_WRITE (PG0_RSAR0, offset & 0xff);
  STNIC_WRITE (PG0_RSAR1, offset >> 8);
  STNIC_WRITE (PG0_RBCR0, length & 0xff);
  STNIC_WRITE (PG0_RBCR1, length >> 8);
  STNIC_WRITE (STNIC_CR, CR_RRD | CR_PG0 | CR_STA);

  if (length & 1)
    length++;

  while (length > 0)
    {
      val = *(vhalf *) PA_83902_IF;
#ifdef __LITTLE_ENDIAN__
      *buf++ = val & 0xff;
      *buf++ = val >> 8;
#else
      *buf++ = val >> 8;
      *buf++ = val & 0xff;
#endif
      STNIC_DELAY ();
      length -= sizeof (half);
    }

  STNIC_WRITE (STNIC_CR, CR_RDMA | CR_PG0 | CR_STA);
}

static void
stnic_block_output (struct net_device *dev, int length,
                    const unsigned char *buf, int output_page)
{
  STNIC_WRITE (PG0_RBCR0, 1);   /* Write non-zero value */
  STNIC_WRITE (STNIC_CR, CR_RRD | CR_PG0 | CR_STA);
  STNIC_DELAY ();

  STNIC_WRITE (PG0_RBCR0, length & 0xff);
  STNIC_WRITE (PG0_RBCR1, length >> 8);
  STNIC_WRITE (PG0_RSAR0, 0);
  STNIC_WRITE (PG0_RSAR1, output_page);
  STNIC_WRITE (STNIC_CR, CR_RWR | CR_PG0 | CR_STA);

  if (length & 1)
    length++;

  while (length > 0)
    {
#ifdef __LITTLE_ENDIAN__
      *(vhalf *) PA_83902_IF = ((half) buf[1] << 8) | buf[0];
#else
      *(vhalf *) PA_83902_IF = ((half) buf[0] << 8) | buf[1];
#endif
      STNIC_DELAY ();
      buf += sizeof (half);
      length -= sizeof (half);
    }

  STNIC_WRITE (STNIC_CR, CR_RDMA | CR_PG0 | CR_STA);
}

/* This function resets the STNIC if something screws up.  */
static void
stnic_init (struct net_device *dev)
{
  stnic_reset (dev);
  NS8390_init (dev, 0);
}

static void __exit stnic_cleanup(void)
{
        unregister_netdev(stnic_dev);
        free_irq(stnic_dev->irq, stnic_dev);
        free_netdev(stnic_dev);
}

module_init(stnic_probe);
module_exit(stnic_cleanup);
MODULE_LICENSE("GPL");