1/* SPDX-License-Identifier: BSD-3-Clause */ 2/* 3 usa67msg.h 4 5 Copyright (c) 1998-2007 InnoSys Incorporated. All Rights Reserved 6 This file is available under a BSD-style copyright 7 8 Keyspan USB Async Firmware to run on Anchor FX1 9 10 Redistribution and use in source and binary forms, with or without 11 modification, are permitted provided that the following conditions are 12 met: 13 14 1. Redistributions of source code must retain this licence text 15 without modification, this list of conditions, and the following 16 disclaimer. The following copyright notice must appear immediately at 17 the beginning of all source files: 18 19 Copyright (c) 1998-2007 InnoSys Incorporated. All Rights Reserved 20 21 This file is available under a BSD-style copyright 22 23 2. Redistributions in binary form must reproduce the above copyright 24 notice, this list of conditions and the following disclaimer in the 25 documentation and/or other materials provided with the distribution. 26 27 3. The name of InnoSys Incorprated may not be used to endorse or promote 28 products derived from this software without specific prior written 29 permission. 30 31 THIS SOFTWARE IS PROVIDED BY INNOSYS CORP. ``AS IS'' AND ANY EXPRESS OR 32 IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 33 OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN 34 NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, 35 INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES 36 (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 37 SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER 38 CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 39 LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 40 OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 41 SUCH DAMAGE. 42 43 Fourth revision: This message format supports the USA28XG 44 45 Buffer formats for RX/TX data messages are not defined by 46 a structure, but are described here: 47 48 USB OUT (host -> USAxx, transmit) messages contain a 49 REQUEST_ACK indicator (set to 0xff to request an ACK at the 50 completion of transmit; 0x00 otherwise), followed by data: 51 52 RQSTACK DAT DAT DAT ... 53 54 with a total data length of up to 63. 55 56 USB IN (USAxx -> host, receive) messages begin with a status 57 byte in which the 0x80 bit is either: 58 59 (a) 0x80 bit clear 60 indicates that the bytes following it are all data 61 bytes: 62 63 STAT DATA DATA DATA DATA DATA ... 64 65 for a total of up to 63 DATA bytes, 66 67 or: 68 69 (b) 0x80 bit set 70 indiates that the bytes following alternate data and 71 status bytes: 72 73 STAT DATA STAT DATA STAT DATA STAT DATA ... 74 75 for a total of up to 32 DATA bytes. 76 77 The valid bits in the STAT bytes are: 78 79 OVERRUN 0x02 80 PARITY 0x04 81 FRAMING 0x08 82 BREAK 0x10 83 84 Notes: 85 86 (1) The OVERRUN bit can appear in either (a) or (b) format 87 messages, but the but the PARITY/FRAMING/BREAK bits 88 only appear in (b) format messages. 89 (2) For the host to determine the exact point at which the 90 overrun occurred (to identify the point in the data 91 stream at which the data was lost), it needs to count 92 128 characters, starting at the first character of the 93 message in which OVERRUN was reported; the lost character(s) 94 would have been received between the 128th and 129th 95 characters. 96 (3) An RX data message in which the first byte has 0x80 clear 97 serves as a "break off" indicator. 98 99 revision history: 100 101 1999feb10 add reportHskiaChanges to allow us to ignore them 102 1999feb10 add txAckThreshold for fast+loose throughput enhancement 103 1999mar30 beef up support for RX error reporting 104 1999apr14 add resetDataToggle to control message 105 2000jan04 merge with usa17msg.h 106 2000jun01 add extended BSD-style copyright text 107 2001jul05 change message format to improve OVERRUN case 108 2002jun05 update copyright date, improve comments 109 2006feb06 modify for FX1 chip 110 111*/ 112 113#ifndef __USA67MSG__ 114#define __USA67MSG__ 115 116 117// all things called "ControlMessage" are sent on the 'control' endpoint 118 119typedef struct keyspan_usa67_portControlMessage 120{ 121 u8 port; // 0 or 1 (selects port) 122 /* 123 there are three types of "commands" sent in the control message: 124 125 1. configuration changes which must be requested by setting 126 the corresponding "set" flag (and should only be requested 127 when necessary, to reduce overhead on the device): 128 */ 129 u8 setClocking, // host requests baud rate be set 130 baudLo, // host does baud divisor calculation 131 baudHi, // baudHi is only used for first port (gives lower rates) 132 externalClock_txClocking, 133 // 0=internal, other=external 134 135 setLcr, // host requests lcr be set 136 lcr, // use PARITY, STOPBITS, DATABITS below 137 138 setFlowControl, // host requests flow control be set 139 ctsFlowControl, // 1=use CTS flow control, 0=don't 140 xonFlowControl, // 1=use XON/XOFF flow control, 0=don't 141 xonChar, // specified in current character format 142 xoffChar, // specified in current character format 143 144 setTxTriState_setRts, 145 // host requests TX tri-state be set 146 txTriState_rts, // 1=active (normal), 0=tristate (off) 147 148 setHskoa_setDtr, 149 // host requests HSKOA output be set 150 hskoa_dtr, // 1=on, 0=off 151 152 setPrescaler, // host requests prescalar be set (default: 13) 153 prescaler; // specified as N/8; values 8-ff are valid 154 // must be set any time internal baud rate is set; 155 // must not be set when external clocking is used 156 157 /* 158 3. configuration data which is simply used as is (no overhead, 159 but must be specified correctly in every host message). 160 */ 161 u8 forwardingLength, // forward when this number of chars available 162 reportHskiaChanges_dsrFlowControl, 163 // 1=normal; 0=ignore external clock 164 // 1=use DSR flow control, 0=don't 165 txAckThreshold, // 0=not allowed, 1=normal, 2-255 deliver ACK faster 166 loopbackMode; // 0=no loopback, 1=loopback enabled 167 168 /* 169 4. commands which are flags only; these are processed in order 170 (so that, e.g., if both _txOn and _txOff flags are set, the 171 port ends in a TX_OFF state); any non-zero value is respected 172 */ 173 u8 _txOn, // enable transmitting (and continue if there's data) 174 _txOff, // stop transmitting 175 txFlush, // toss outbound data 176 txBreak, // turn on break (cleared by _txOn) 177 rxOn, // turn on receiver 178 rxOff, // turn off receiver 179 rxFlush, // toss inbound data 180 rxForward, // forward all inbound data, NOW (as if fwdLen==1) 181 returnStatus, // return current status (even if it hasn't changed) 182 resetDataToggle;// reset data toggle state to DATA0 183 184} keyspan_usa67_portControlMessage; 185 186// defines for bits in lcr 187#define USA_DATABITS_5 0x00 188#define USA_DATABITS_6 0x01 189#define USA_DATABITS_7 0x02 190#define USA_DATABITS_8 0x03 191#define STOPBITS_5678_1 0x00 // 1 stop bit for all byte sizes 192#define STOPBITS_5_1p5 0x04 // 1.5 stop bits for 5-bit byte 193#define STOPBITS_678_2 0x04 // 2 stop bits for 6/7/8-bit byte 194#define USA_PARITY_NONE 0x00 195#define USA_PARITY_ODD 0x08 196#define USA_PARITY_EVEN 0x18 197#define PARITY_1 0x28 198#define PARITY_0 0x38 199 200// all things called "StatusMessage" are sent on the status endpoint 201 202typedef struct keyspan_usa67_portStatusMessage // one for each port 203{ 204 u8 port, // 0=first, 1=second, other=see below 205 hskia_cts, // reports HSKIA pin 206 gpia_dcd, // reports GPIA pin 207 _txOff, // port has been disabled (by host) 208 _txXoff, // port is in XOFF state (either host or RX XOFF) 209 txAck, // indicates a TX message acknowledgement 210 rxEnabled, // as configured by rxOn/rxOff 1=on, 0=off 211 controlResponse;// 1=a control message has been processed 212} keyspan_usa67_portStatusMessage; 213 214// bits in RX data message when STAT byte is included 215#define RXERROR_OVERRUN 0x02 216#define RXERROR_PARITY 0x04 217#define RXERROR_FRAMING 0x08 218#define RXERROR_BREAK 0x10 219 220typedef struct keyspan_usa67_globalControlMessage 221{ 222 u8 port, // 3 223 sendGlobalStatus, // 2=request for two status responses 224 resetStatusToggle, // 1=reset global status toggle 225 resetStatusCount; // a cycling value 226} keyspan_usa67_globalControlMessage; 227 228typedef struct keyspan_usa67_globalStatusMessage 229{ 230 u8 port, // 3 231 sendGlobalStatus, // from request, decremented 232 resetStatusCount; // as in request 233} keyspan_usa67_globalStatusMessage; 234 235typedef struct keyspan_usa67_globalDebugMessage 236{ 237 u8 port, // 2 238 a, 239 b, 240 c, 241 d; 242} keyspan_usa67_globalDebugMessage; 243 244// ie: the maximum length of an FX1 endpoint buffer 245#define MAX_DATA_LEN 64 246 247// update status approx. 60 times a second (16.6666 ms) 248#define STATUS_UPDATE_INTERVAL 16 249 250// status rationing tuning value (each port gets checked each n ms) 251#define STATUS_RATION 10 252 253#endif 254 255 256