1
2
3
4
5
6
7
8
9
10
11#include <linux/types.h>
12#include <linux/init.h>
13#include <linux/platform_device.h>
14#include <linux/mtd/physmap.h>
15#include <linux/memory.h>
16#include <linux/gpio.h>
17
18#include <asm/mach-types.h>
19#include <asm/mach/arch.h>
20#include <asm/mach/time.h>
21
22#include <linux/i2c.h>
23#include <linux/mfd/mc13xxx.h>
24
25#include "common.h"
26#include "devices-imx35.h"
27#include "ehci.h"
28#include "hardware.h"
29#include "iomux-mx35.h"
30
31#define GPIO_LCDPWR IMX_GPIO_NR(1, 2)
32#define GPIO_PMIC_INT IMX_GPIO_NR(2, 0)
33
34#define GPIO_BUTTON1 IMX_GPIO_NR(1, 4)
35#define GPIO_BUTTON2 IMX_GPIO_NR(1, 5)
36#define GPIO_BUTTON3 IMX_GPIO_NR(1, 7)
37#define GPIO_BUTTON4 IMX_GPIO_NR(1, 8)
38#define GPIO_BUTTON5 IMX_GPIO_NR(1, 9)
39#define GPIO_BUTTON6 IMX_GPIO_NR(1, 10)
40#define GPIO_BUTTON7 IMX_GPIO_NR(1, 11)
41#define GPIO_BUTTON8 IMX_GPIO_NR(1, 12)
42
43static const struct fb_videomode fb_modedb[] = {
44 {
45
46 .name = "PT0708048",
47 .refresh = 60,
48 .xres = 800,
49 .yres = 480,
50 .pixclock = KHZ2PICOS(33260),
51 .left_margin = 50,
52 .right_margin = 156,
53 .upper_margin = 10,
54 .lower_margin = 10,
55 .hsync_len = 1,
56 .vsync_len = 1,
57 .sync = FB_SYNC_CLK_IDLE_EN | FB_SYNC_OE_ACT_HIGH,
58 .vmode = FB_VMODE_NONINTERLACED,
59 .flag = 0,
60 }, {
61
62 .name = "CTP-CLAA070LC0ACW",
63 .refresh = 60,
64 .xres = 800,
65 .yres = 480,
66 .pixclock = KHZ2PICOS(27000),
67 .left_margin = 50,
68 .right_margin = 50,
69 .upper_margin = 10,
70 .lower_margin = 10,
71 .hsync_len = 1,
72 .vsync_len = 1,
73 .sync = FB_SYNC_CLK_IDLE_EN | FB_SYNC_OE_ACT_HIGH,
74 .vmode = FB_VMODE_NONINTERLACED,
75 .flag = 0,
76 }
77};
78
79static struct mx3fb_platform_data mx3fb_pdata __initdata = {
80 .name = "PT0708048",
81 .mode = fb_modedb,
82 .num_modes = ARRAY_SIZE(fb_modedb),
83};
84
85static struct physmap_flash_data vpr200_flash_data = {
86 .width = 2,
87};
88
89static struct resource vpr200_flash_resource = {
90 .start = MX35_CS0_BASE_ADDR,
91 .end = MX35_CS0_BASE_ADDR + SZ_64M - 1,
92 .flags = IORESOURCE_MEM,
93};
94
95static struct platform_device vpr200_flash = {
96 .name = "physmap-flash",
97 .id = 0,
98 .dev = {
99 .platform_data = &vpr200_flash_data,
100 },
101 .resource = &vpr200_flash_resource,
102 .num_resources = 1,
103};
104
105static const struct mxc_nand_platform_data
106 vpr200_nand_board_info __initconst = {
107 .width = 1,
108 .hw_ecc = 1,
109 .flash_bbt = 1,
110};
111
112#define VPR_KEY_DEBOUNCE 500
113static struct gpio_keys_button vpr200_gpio_keys_table[] = {
114 {KEY_F2, GPIO_BUTTON1, 1, "vpr-keys: F2", 0, VPR_KEY_DEBOUNCE},
115 {KEY_F3, GPIO_BUTTON2, 1, "vpr-keys: F3", 0, VPR_KEY_DEBOUNCE},
116 {KEY_F4, GPIO_BUTTON3, 1, "vpr-keys: F4", 0, VPR_KEY_DEBOUNCE},
117 {KEY_F5, GPIO_BUTTON4, 1, "vpr-keys: F5", 0, VPR_KEY_DEBOUNCE},
118 {KEY_F6, GPIO_BUTTON5, 1, "vpr-keys: F6", 0, VPR_KEY_DEBOUNCE},
119 {KEY_F7, GPIO_BUTTON6, 1, "vpr-keys: F7", 0, VPR_KEY_DEBOUNCE},
120 {KEY_F8, GPIO_BUTTON7, 1, "vpr-keys: F8", 1, VPR_KEY_DEBOUNCE},
121 {KEY_F9, GPIO_BUTTON8, 1, "vpr-keys: F9", 1, VPR_KEY_DEBOUNCE},
122};
123
124static const struct gpio_keys_platform_data
125 vpr200_gpio_keys_data __initconst = {
126 .buttons = vpr200_gpio_keys_table,
127 .nbuttons = ARRAY_SIZE(vpr200_gpio_keys_table),
128};
129
130static struct mc13xxx_platform_data vpr200_pmic = {
131 .flags = MC13XXX_USE_ADC | MC13XXX_USE_TOUCHSCREEN,
132};
133
134static const struct imxi2c_platform_data vpr200_i2c0_data __initconst = {
135 .bitrate = 50000,
136};
137
138static struct i2c_board_info vpr200_i2c_devices[] = {
139 {
140 I2C_BOARD_INFO("24c02", 0x50),
141 }, {
142 I2C_BOARD_INFO("mc13892", 0x08),
143 .platform_data = &vpr200_pmic,
144
145 }
146};
147
148static const iomux_v3_cfg_t vpr200_pads[] __initconst = {
149
150 MX35_PAD_TXD1__UART1_TXD_MUX,
151 MX35_PAD_RXD1__UART1_RXD_MUX,
152
153 MX35_PAD_ATA_DATA10__UART3_RXD_MUX,
154 MX35_PAD_ATA_DATA11__UART3_TXD_MUX,
155
156 MX35_PAD_FEC_TX_CLK__FEC_TX_CLK,
157 MX35_PAD_FEC_RX_CLK__FEC_RX_CLK,
158 MX35_PAD_FEC_RX_DV__FEC_RX_DV,
159 MX35_PAD_FEC_COL__FEC_COL,
160 MX35_PAD_FEC_RDATA0__FEC_RDATA_0,
161 MX35_PAD_FEC_TDATA0__FEC_TDATA_0,
162 MX35_PAD_FEC_TX_EN__FEC_TX_EN,
163 MX35_PAD_FEC_MDC__FEC_MDC,
164 MX35_PAD_FEC_MDIO__FEC_MDIO,
165 MX35_PAD_FEC_TX_ERR__FEC_TX_ERR,
166 MX35_PAD_FEC_RX_ERR__FEC_RX_ERR,
167 MX35_PAD_FEC_CRS__FEC_CRS,
168 MX35_PAD_FEC_RDATA1__FEC_RDATA_1,
169 MX35_PAD_FEC_TDATA1__FEC_TDATA_1,
170 MX35_PAD_FEC_RDATA2__FEC_RDATA_2,
171 MX35_PAD_FEC_TDATA2__FEC_TDATA_2,
172 MX35_PAD_FEC_RDATA3__FEC_RDATA_3,
173 MX35_PAD_FEC_TDATA3__FEC_TDATA_3,
174
175 MX35_PAD_LD0__IPU_DISPB_DAT_0,
176 MX35_PAD_LD1__IPU_DISPB_DAT_1,
177 MX35_PAD_LD2__IPU_DISPB_DAT_2,
178 MX35_PAD_LD3__IPU_DISPB_DAT_3,
179 MX35_PAD_LD4__IPU_DISPB_DAT_4,
180 MX35_PAD_LD5__IPU_DISPB_DAT_5,
181 MX35_PAD_LD6__IPU_DISPB_DAT_6,
182 MX35_PAD_LD7__IPU_DISPB_DAT_7,
183 MX35_PAD_LD8__IPU_DISPB_DAT_8,
184 MX35_PAD_LD9__IPU_DISPB_DAT_9,
185 MX35_PAD_LD10__IPU_DISPB_DAT_10,
186 MX35_PAD_LD11__IPU_DISPB_DAT_11,
187 MX35_PAD_LD12__IPU_DISPB_DAT_12,
188 MX35_PAD_LD13__IPU_DISPB_DAT_13,
189 MX35_PAD_LD14__IPU_DISPB_DAT_14,
190 MX35_PAD_LD15__IPU_DISPB_DAT_15,
191 MX35_PAD_LD16__IPU_DISPB_DAT_16,
192 MX35_PAD_LD17__IPU_DISPB_DAT_17,
193 MX35_PAD_D3_FPSHIFT__IPU_DISPB_D3_CLK,
194 MX35_PAD_D3_DRDY__IPU_DISPB_D3_DRDY,
195 MX35_PAD_CONTRAST__IPU_DISPB_CONTR,
196
197 MX35_PAD_D3_VSYNC__GPIO1_2,
198
199 MX35_PAD_USBOTG_PWR__USB_TOP_USBOTG_PWR,
200 MX35_PAD_USBOTG_OC__USB_TOP_USBOTG_OC,
201
202 MX35_PAD_SD1_CMD__ESDHC1_CMD,
203 MX35_PAD_SD1_CLK__ESDHC1_CLK,
204 MX35_PAD_SD1_DATA0__ESDHC1_DAT0,
205 MX35_PAD_SD1_DATA1__ESDHC1_DAT1,
206 MX35_PAD_SD1_DATA2__ESDHC1_DAT2,
207 MX35_PAD_SD1_DATA3__ESDHC1_DAT3,
208
209 MX35_PAD_GPIO2_0__GPIO2_0,
210
211 MX35_PAD_SCKR__GPIO1_4,
212 MX35_PAD_COMPARE__GPIO1_5,
213 MX35_PAD_SCKT__GPIO1_7,
214 MX35_PAD_FST__GPIO1_8,
215 MX35_PAD_HCKT__GPIO1_9,
216 MX35_PAD_TX5_RX0__GPIO1_10,
217 MX35_PAD_TX4_RX1__GPIO1_11,
218 MX35_PAD_TX3_RX2__GPIO1_12,
219};
220
221
222static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
223 .operating_mode = FSL_USB2_DR_DEVICE,
224 .phy_mode = FSL_USB2_PHY_UTMI,
225 .workaround = FLS_USB2_WORKAROUND_ENGCM09152,
226};
227
228static int vpr200_usbh_init(struct platform_device *pdev)
229{
230 return mx35_initialize_usb_hw(pdev->id,
231 MXC_EHCI_INTERFACE_SINGLE_UNI | MXC_EHCI_INTERNAL_PHY);
232}
233
234
235static const struct mxc_usbh_platform_data usb_host_pdata __initconst = {
236 .init = vpr200_usbh_init,
237 .portsc = MXC_EHCI_MODE_SERIAL,
238};
239
240static struct platform_device *devices[] __initdata = {
241 &vpr200_flash,
242};
243
244
245
246
247static void __init vpr200_board_init(void)
248{
249 imx35_soc_init();
250
251 mxc_iomux_v3_setup_multiple_pads(vpr200_pads, ARRAY_SIZE(vpr200_pads));
252
253 imx35_add_fec(NULL);
254 imx35_add_imx2_wdt();
255
256 imx35_add_imx_uart0(NULL);
257 imx35_add_imx_uart2(NULL);
258
259 imx35_add_ipu_core();
260 imx35_add_mx3_sdc_fb(&mx3fb_pdata);
261
262 imx35_add_fsl_usb2_udc(&otg_device_pdata);
263 imx35_add_mxc_ehci_hs(&usb_host_pdata);
264
265 imx35_add_mxc_nand(&vpr200_nand_board_info);
266 imx35_add_sdhci_esdhc_imx(0, NULL);
267}
268
269static void __init vpr200_late_init(void)
270{
271 imx_add_gpio_keys(&vpr200_gpio_keys_data);
272
273 platform_add_devices(devices, ARRAY_SIZE(devices));
274
275 if (0 != gpio_request(GPIO_LCDPWR, "LCDPWR"))
276 printk(KERN_WARNING "vpr200: Couldn't get LCDPWR gpio\n");
277 else
278 gpio_direction_output(GPIO_LCDPWR, 0);
279
280 if (0 != gpio_request(GPIO_PMIC_INT, "PMIC_INT"))
281 printk(KERN_WARNING "vpr200: Couldn't get PMIC_INT gpio\n");
282 else
283 gpio_direction_input(GPIO_PMIC_INT);
284
285 vpr200_i2c_devices[1].irq = gpio_to_irq(GPIO_PMIC_INT);
286 i2c_register_board_info(0, vpr200_i2c_devices,
287 ARRAY_SIZE(vpr200_i2c_devices));
288
289 imx35_add_imx_i2c0(&vpr200_i2c0_data);
290}
291
292static void __init vpr200_timer_init(void)
293{
294 mx35_clocks_init();
295}
296
297MACHINE_START(VPR200, "VPR200")
298
299 .map_io = mx35_map_io,
300 .init_early = imx35_init_early,
301 .init_irq = mx35_init_irq,
302 .init_time = vpr200_timer_init,
303 .init_machine = vpr200_board_init,
304 .init_late = vpr200_late_init,
305 .restart = mxc_restart,
306MACHINE_END
307
