// SPDX-License-Identifier: GPL-2.0-only
/*
 * Libata based driver for Apple "macio" family of PATA controllers
 *
 * Copyright 2008/2009 Benjamin Herrenschmidt, IBM Corp
 *                     <benh@kernel.crashing.org>
 *
 * Some bits and pieces from drivers/ide/ppc/pmac.c
 *
 */

#undef DEBUG
#undef DEBUG_DMA

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/ata.h>
#include <linux/libata.h>
#include <linux/adb.h>
#include <linux/pmu.h>
#include <linux/scatterlist.h>
#include <linux/of.h>
#include <linux/gfp.h>
#include <linux/pci.h>

#include <scsi/scsi.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_device.h>

#include <asm/macio.h>
#include <asm/io.h>
#include <asm/dbdma.h>
#include <asm/machdep.h>
#include <asm/pmac_feature.h>
#include <asm/mediabay.h>

#ifdef DEBUG_DMA
#define dev_dbgdma(dev, format, arg...)         \
        dev_printk(KERN_DEBUG , dev , format , ## arg)
#else
#define dev_dbgdma(dev, format, arg...)         \
        ({ if (0) dev_printk(KERN_DEBUG, dev, format, ##arg); 0; })
#endif

#define DRV_NAME        "pata_macio"
#define DRV_VERSION     "0.9"

/* Models of macio ATA controller */
enum {
        controller_ohare,       /* OHare based */
        controller_heathrow,    /* Heathrow/Paddington */
        controller_kl_ata3,     /* KeyLargo ATA-3 */
        controller_kl_ata4,     /* KeyLargo ATA-4 */
        controller_un_ata6,     /* UniNorth2 ATA-6 */
        controller_k2_ata6,     /* K2 ATA-6 */
        controller_sh_ata6,     /* Shasta ATA-6 */
};

static const char* macio_ata_names[] = {
        "OHare ATA",            /* OHare based */
        "Heathrow ATA",         /* Heathrow/Paddington */
        "KeyLargo ATA-3",       /* KeyLargo ATA-3 (MDMA only) */
        "KeyLargo ATA-4",       /* KeyLargo ATA-4 (UDMA/66) */
        "UniNorth ATA-6",       /* UniNorth2 ATA-6 (UDMA/100) */
        "K2 ATA-6",             /* K2 ATA-6 (UDMA/100) */
        "Shasta ATA-6",         /* Shasta ATA-6 (UDMA/133) */
};

/*
 * Extra registers, both 32-bit little-endian
 */
#define IDE_TIMING_CONFIG       0x200
#define IDE_INTERRUPT           0x300

/* Kauai (U2) ATA has different register setup */
#define IDE_KAUAI_PIO_CONFIG    0x200
#define IDE_KAUAI_ULTRA_CONFIG  0x210
#define IDE_KAUAI_POLL_CONFIG   0x220

/*
 * Timing configuration register definitions
 */

/* Number of IDE_SYSCLK_NS ticks, argument is in nanoseconds */
#define SYSCLK_TICKS(t)         (((t) + IDE_SYSCLK_NS - 1) / IDE_SYSCLK_NS)
#define SYSCLK_TICKS_66(t)      (((t) + IDE_SYSCLK_66_NS - 1) / IDE_SYSCLK_66_NS)
#define IDE_SYSCLK_NS           30      /* 33Mhz cell */
#define IDE_SYSCLK_66_NS        15      /* 66Mhz cell */

/* 133Mhz cell, found in shasta.
 * See comments about 100 Mhz Uninorth 2...
 * Note that PIO_MASK and MDMA_MASK seem to overlap, that's just
 * weird and I don't now why .. at this stage
 */
#define TR_133_PIOREG_PIO_MASK          0xff000fff
#define TR_133_PIOREG_MDMA_MASK         0x00fff800
#define TR_133_UDMAREG_UDMA_MASK        0x0003ffff
#define TR_133_UDMAREG_UDMA_EN          0x00000001

/* 100Mhz cell, found in Uninorth 2 and K2. It appears as a pci device
 * (106b/0033) on uninorth or K2 internal PCI bus and it's clock is
 * controlled like gem or fw. It appears to be an evolution of keylargo
 * ATA4 with a timing register extended to 2x32bits registers (one
 * for PIO & MWDMA and one for UDMA, and a similar DBDMA channel.
 * It has it's own local feature control register as well.
 *
 * After scratching my mind over the timing values, at least for PIO
 * and MDMA, I think I've figured the format of the timing register,
 * though I use pre-calculated tables for UDMA as usual...
 */
#define TR_100_PIO_ADDRSETUP_MASK       0xff000000 /* Size of field unknown */
#define TR_100_PIO_ADDRSETUP_SHIFT      24
#define TR_100_MDMA_MASK                0x00fff000
#define TR_100_MDMA_RECOVERY_MASK       0x00fc0000
#define TR_100_MDMA_RECOVERY_SHIFT      18
#define TR_100_MDMA_ACCESS_MASK         0x0003f000
#define TR_100_MDMA_ACCESS_SHIFT        12
#define TR_100_PIO_MASK                 0xff000fff
#define TR_100_PIO_RECOVERY_MASK        0x00000fc0
#define TR_100_PIO_RECOVERY_SHIFT       6
#define TR_100_PIO_ACCESS_MASK          0x0000003f
#define TR_100_PIO_ACCESS_SHIFT         0

#define TR_100_UDMAREG_UDMA_MASK        0x0000ffff
#define TR_100_UDMAREG_UDMA_EN          0x00000001


/* 66Mhz cell, found in KeyLargo. Can do ultra mode 0 to 2 on
 * 40 connector cable and to 4 on 80 connector one.
 * Clock unit is 15ns (66Mhz)
 *
 * 3 Values can be programmed:
 *  - Write data setup, which appears to match the cycle time. They
 *    also call it DIOW setup.
 *  - Ready to pause time (from spec)
 *  - Address setup. That one is weird. I don't see where exactly
 *    it fits in UDMA cycles, I got it's name from an obscure piece
 *    of commented out code in Darwin. They leave it to 0, we do as
 *    well, despite a comment that would lead to think it has a
 *    min value of 45ns.
 * Apple also add 60ns to the write data setup (or cycle time ?) on
 * reads.
 */
#define TR_66_UDMA_MASK                 0xfff00000
#define TR_66_UDMA_EN                   0x00100000 /* Enable Ultra mode for DMA */
#define TR_66_PIO_ADDRSETUP_MASK        0xe0000000 /* Address setup */
#define TR_66_PIO_ADDRSETUP_SHIFT       29
#define TR_66_UDMA_RDY2PAUS_MASK        0x1e000000 /* Ready 2 pause time */
#define TR_66_UDMA_RDY2PAUS_SHIFT       25
#define TR_66_UDMA_WRDATASETUP_MASK     0x01e00000 /* Write data setup time */
#define TR_66_UDMA_WRDATASETUP_SHIFT    21
#define TR_66_MDMA_MASK                 0x000ffc00
#define TR_66_MDMA_RECOVERY_MASK        0x000f8000
#define TR_66_MDMA_RECOVERY_SHIFT       15
#define TR_66_MDMA_ACCESS_MASK          0x00007c00
#define TR_66_MDMA_ACCESS_SHIFT         10
#define TR_66_PIO_MASK                  0xe00003ff
#define TR_66_PIO_RECOVERY_MASK         0x000003e0
#define TR_66_PIO_RECOVERY_SHIFT        5
#define TR_66_PIO_ACCESS_MASK           0x0000001f
#define TR_66_PIO_ACCESS_SHIFT          0

/* 33Mhz cell, found in OHare, Heathrow (& Paddington) and KeyLargo
 * Can do pio & mdma modes, clock unit is 30ns (33Mhz)
 *
 * The access time and recovery time can be programmed. Some older
 * Darwin code base limit OHare to 150ns cycle time. I decided to do
 * the same here fore safety against broken old hardware ;)
 * The HalfTick bit, when set, adds half a clock (15ns) to the access
 * time and removes one from recovery. It's not supported on KeyLargo
 * implementation afaik. The E bit appears to be set for PIO mode 0 and
 * is used to reach long timings used in this mode.
 */
#define TR_33_MDMA_MASK                 0x003ff800
#define TR_33_MDMA_RECOVERY_MASK        0x001f0000
#define TR_33_MDMA_RECOVERY_SHIFT       16
#define TR_33_MDMA_ACCESS_MASK          0x0000f800
#define TR_33_MDMA_ACCESS_SHIFT         11
#define TR_33_MDMA_HALFTICK             0x00200000
#define TR_33_PIO_MASK                  0x000007ff
#define TR_33_PIO_E                     0x00000400
#define TR_33_PIO_RECOVERY_MASK         0x000003e0
#define TR_33_PIO_RECOVERY_SHIFT        5
#define TR_33_PIO_ACCESS_MASK           0x0000001f
#define TR_33_PIO_ACCESS_SHIFT          0

/*
 * Interrupt register definitions. Only present on newer cells
 * (Keylargo and later afaik) so we don't use it.
 */
#define IDE_INTR_DMA                    0x80000000
#define IDE_INTR_DEVICE                 0x40000000

/*
 * FCR Register on Kauai. Not sure what bit 0x4 is  ...
 */
#define KAUAI_FCR_UATA_MAGIC            0x00000004
#define KAUAI_FCR_UATA_RESET_N          0x00000002
#define KAUAI_FCR_UATA_ENABLE           0x00000001


/* Allow up to 256 DBDMA commands per xfer */
#define MAX_DCMDS               256

/* Don't let a DMA segment go all the way to 64K */
#define MAX_DBDMA_SEG           0xff00


/*
 * Wait 1s for disk to answer on IDE bus after a hard reset
 * of the device (via GPIO/FCR).
 *
 * Some devices seem to "pollute" the bus even after dropping
 * the BSY bit (typically some combo drives slave on the UDMA
 * bus) after a hard reset. Since we hard reset all drives on
 * KeyLargo ATA66, we have to keep that delay around. I may end
 * up not hard resetting anymore on these and keep the delay only
 * for older interfaces instead (we have to reset when coming
 * from MacOS...) --BenH.
 */
#define IDE_WAKEUP_DELAY_MS     1000

struct pata_macio_timing;

struct pata_macio_priv {
        int                             kind;
        int                             aapl_bus_id;
        int                             mediabay : 1;
        struct device_node              *node;
        struct macio_dev                *mdev;
        struct pci_dev                  *pdev;
        struct device                   *dev;
        int                             irq;
        u32                             treg[2][2];
        void __iomem                    *tfregs;
        void __iomem                    *kauai_fcr;
        struct dbdma_cmd *              dma_table_cpu;
        dma_addr_t                      dma_table_dma;
        struct ata_host                 *host;
        const struct pata_macio_timing  *timings;
};

/* Previous variants of this driver used to calculate timings
 * for various variants of the chip and use tables for others.
 *
 * Not only was this confusing, but in addition, it isn't clear
 * whether our calculation code was correct. It didn't entirely
 * match the darwin code and whatever documentation I could find
 * on these cells
 *
 * I decided to entirely rely on a table instead for this version
 * of the driver. Also, because I don't really care about derated
 * modes and really old HW other than making it work, I'm not going
 * to calculate / snoop timing values for something else than the
 * standard modes.
 */
struct pata_macio_timing {
        int     mode;
        u32     reg1;   /* Bits to set in first timing reg */
        u32     reg2;   /* Bits to set in second timing reg */
};

static const struct pata_macio_timing pata_macio_ohare_timings[] = {
        { XFER_PIO_0,           0x00000526,     0, },
        { XFER_PIO_1,           0x00000085,     0, },
        { XFER_PIO_2,           0x00000025,     0, },
        { XFER_PIO_3,           0x00000025,     0, },
        { XFER_PIO_4,           0x00000025,     0, },
        { XFER_MW_DMA_0,        0x00074000,     0, },
        { XFER_MW_DMA_1,        0x00221000,     0, },
        { XFER_MW_DMA_2,        0x00211000,     0, },
        { -1, 0, 0 }
};

static const struct pata_macio_timing pata_macio_heathrow_timings[] = {
        { XFER_PIO_0,           0x00000526,     0, },
        { XFER_PIO_1,           0x00000085,     0, },
        { XFER_PIO_2,           0x00000025,     0, },
        { XFER_PIO_3,           0x00000025,     0, },
        { XFER_PIO_4,           0x00000025,     0, },
        { XFER_MW_DMA_0,        0x00074000,     0, },
        { XFER_MW_DMA_1,        0x00221000,     0, },
        { XFER_MW_DMA_2,        0x00211000,     0, },
        { -1, 0, 0 }
};

static const struct pata_macio_timing pata_macio_kl33_timings[] = {
        { XFER_PIO_0,           0x00000526,     0, },
        { XFER_PIO_1,           0x00000085,     0, },
        { XFER_PIO_2,           0x00000025,     0, },
        { XFER_PIO_3,           0x00000025,     0, },
        { XFER_PIO_4,           0x00000025,     0, },
        { XFER_MW_DMA_0,        0x00084000,     0, },
        { XFER_MW_DMA_1,        0x00021800,     0, },
        { XFER_MW_DMA_2,        0x00011800,     0, },
        { -1, 0, 0 }
};

static const struct pata_macio_timing pata_macio_kl66_timings[] = {
        { XFER_PIO_0,           0x0000038c,     0, },
        { XFER_PIO_1,           0x0000020a,     0, },
        { XFER_PIO_2,           0x00000127,     0, },
        { XFER_PIO_3,           0x000000c6,     0, },
        { XFER_PIO_4,           0x00000065,     0, },
        { XFER_MW_DMA_0,        0x00084000,     0, },
        { XFER_MW_DMA_1,        0x00029800,     0, },
        { XFER_MW_DMA_2,        0x00019400,     0, },
        { XFER_UDMA_0,          0x19100000,     0, },
        { XFER_UDMA_1,          0x14d00000,     0, },
        { XFER_UDMA_2,          0x10900000,     0, },
        { XFER_UDMA_3,          0x0c700000,     0, },
        { XFER_UDMA_4,          0x0c500000,     0, },
        { -1, 0, 0 }
};

static const struct pata_macio_timing pata_macio_kauai_timings[] = {
        { XFER_PIO_0,           0x08000a92,     0, },
        { XFER_PIO_1,           0x0800060f,     0, },
        { XFER_PIO_2,           0x0800038b,     0, },
        { XFER_PIO_3,           0x05000249,     0, },
        { XFER_PIO_4,           0x04000148,     0, },
        { XFER_MW_DMA_0,        0x00618000,     0, },
        { XFER_MW_DMA_1,        0x00209000,     0, },
        { XFER_MW_DMA_2,        0x00148000,     0, },
        { XFER_UDMA_0,                   0,     0x000070c1, },
        { XFER_UDMA_1,                   0,     0x00005d81, },
        { XFER_UDMA_2,                   0,     0x00004a61, },
        { XFER_UDMA_3,                   0,     0x00003a51, },
        { XFER_UDMA_4,                   0,     0x00002a31, },
        { XFER_UDMA_5,                   0,     0x00002921, },
        { -1, 0, 0 }
};

static const struct pata_macio_timing pata_macio_shasta_timings[] = {
        { XFER_PIO_0,           0x0a000c97,     0, },
        { XFER_PIO_1,           0x07000712,     0, },
        { XFER_PIO_2,           0x040003cd,     0, },
        { XFER_PIO_3,           0x0500028b,     0, },
        { XFER_PIO_4,           0x0400010a,     0, },
        { XFER_MW_DMA_0,        0x00820800,     0, },
        { XFER_MW_DMA_1,        0x0028b000,     0, },
        { XFER_MW_DMA_2,        0x001ca000,     0, },
        { XFER_UDMA_0,                   0,     0x00035901, },
        { XFER_UDMA_1,                   0,     0x000348b1, },
        { XFER_UDMA_2,                   0,     0x00033881, },
        { XFER_UDMA_3,                   0,     0x00033861, },
        { XFER_UDMA_4,                   0,     0x00033841, },
        { XFER_UDMA_5,                   0,     0x00033031, },
        { XFER_UDMA_6,                   0,     0x00033021, },
        { -1, 0, 0 }
};

static const struct pata_macio_timing *pata_macio_find_timing(
                                            struct pata_macio_priv *priv,
                                            int mode)
{
        int i;

        for (i = 0; priv->timings[i].mode > 0; i++) {
                if (priv->timings[i].mode == mode)
                        return &priv->timings[i];
        }
        return NULL;
}


static void pata_macio_apply_timings(struct ata_port *ap, unsigned int device)
{
        struct pata_macio_priv *priv = ap->private_data;
        void __iomem *rbase = ap->ioaddr.cmd_addr;

        if (priv->kind == controller_sh_ata6 ||
            priv->kind == controller_un_ata6 ||
            priv->kind == controller_k2_ata6) {
                writel(priv->treg[device][0], rbase + IDE_KAUAI_PIO_CONFIG);
                writel(priv->treg[device][1], rbase + IDE_KAUAI_ULTRA_CONFIG);
        } else
                writel(priv->treg[device][0], rbase + IDE_TIMING_CONFIG);
}

static void pata_macio_dev_select(struct ata_port *ap, unsigned int device)
{
        ata_sff_dev_select(ap, device);

        /* Apply timings */
        pata_macio_apply_timings(ap, device);
}

static void pata_macio_set_timings(struct ata_port *ap,
                                   struct ata_device *adev)
{
        struct pata_macio_priv *priv = ap->private_data;
        const struct pata_macio_timing *t;

        dev_dbg(priv->dev, "Set timings: DEV=%d,PIO=0x%x (%s),DMA=0x%x (%s)\n",
                adev->devno,
                adev->pio_mode,
                ata_mode_string(ata_xfer_mode2mask(adev->pio_mode)),
                adev->dma_mode,
                ata_mode_string(ata_xfer_mode2mask(adev->dma_mode)));

        /* First clear timings */
        priv->treg[adev->devno][0] = priv->treg[adev->devno][1] = 0;

        /* Now get the PIO timings */
        t = pata_macio_find_timing(priv, adev->pio_mode);
        if (t == NULL) {
                dev_warn(priv->dev, "Invalid PIO timing requested: 0x%x\n",
                         adev->pio_mode);
                t = pata_macio_find_timing(priv, XFER_PIO_0);
        }
        BUG_ON(t == NULL);

        /* PIO timings only ever use the first treg */
        priv->treg[adev->devno][0] |= t->reg1;

        /* Now get DMA timings */
        t = pata_macio_find_timing(priv, adev->dma_mode);
        if (t == NULL || (t->reg1 == 0 && t->reg2 == 0)) {
                dev_dbg(priv->dev, "DMA timing not set yet, using MW_DMA_0\n");
                t = pata_macio_find_timing(priv, XFER_MW_DMA_0);
        }
        BUG_ON(t == NULL);

        /* DMA timings can use both tregs */
        priv->treg[adev->devno][0] |= t->reg1;
        priv->treg[adev->devno][1] |= t->reg2;

        dev_dbg(priv->dev, " -> %08x %08x\n",
                priv->treg[adev->devno][0],
                priv->treg[adev->devno][1]);

        /* Apply to hardware */
        pata_macio_apply_timings(ap, adev->devno);
}

/*
 * Blast some well known "safe" values to the timing registers at init or
 * wakeup from sleep time, before we do real calculation
 */
static void pata_macio_default_timings(struct pata_macio_priv *priv)
{
        unsigned int value, value2 = 0;

        switch(priv->kind) {
                case controller_sh_ata6:
                        value = 0x0a820c97;
                        value2 = 0x00033031;
                        break;
                case controller_un_ata6:
                case controller_k2_ata6:
                        value = 0x08618a92;
                        value2 = 0x00002921;
                        break;
                case controller_kl_ata4:
                        value = 0x0008438c;
                        break;
                case controller_kl_ata3:
                        value = 0x00084526;
                        break;
                case controller_heathrow:
                case controller_ohare:
                default:
                        value = 0x00074526;
                        break;
        }
        priv->treg[0][0] = priv->treg[1][0] = value;
        priv->treg[0][1] = priv->treg[1][1] = value2;
}

static int pata_macio_cable_detect(struct ata_port *ap)
{
        struct pata_macio_priv *priv = ap->private_data;

        /* Get cable type from device-tree */
        if (priv->kind == controller_kl_ata4 ||
            priv->kind == controller_un_ata6 ||
            priv->kind == controller_k2_ata6 ||
            priv->kind == controller_sh_ata6) {
                const char* cable = of_get_property(priv->node, "cable-type",
                                                    NULL);
                struct device_node *root = of_find_node_by_path("/");
                const char *model = of_get_property(root, "model", NULL);

                of_node_put(root);

                if (cable && !strncmp(cable, "80-", 3)) {
                        /* Some drives fail to detect 80c cable in PowerBook
                         * These machine use proprietary short IDE cable
                         * anyway
                         */
                        if (!strncmp(model, "PowerBook", 9))
                                return ATA_CBL_PATA40_SHORT;
                        else
                                return ATA_CBL_PATA80;
                }
        }

        /* G5's seem to have incorrect cable type in device-tree.
         * Let's assume they always have a 80 conductor cable, this seem to
         * be always the case unless the user mucked around
         */
        if (of_device_is_compatible(priv->node, "K2-UATA") ||
            of_device_is_compatible(priv->node, "shasta-ata"))
                return ATA_CBL_PATA80;

        /* Anything else is 40 connectors */
        return ATA_CBL_PATA40;
}

static void pata_macio_qc_prep(struct ata_queued_cmd *qc)
{
        unsigned int write = (qc->tf.flags & ATA_TFLAG_WRITE);
        struct ata_port *ap = qc->ap;
        struct pata_macio_priv *priv = ap->private_data;
        struct scatterlist *sg;
        struct dbdma_cmd *table;
        unsigned int si, pi;

        dev_dbgdma(priv->dev, "%s: qc %p flags %lx, write %d dev %d\n",
                   __func__, qc, qc->flags, write, qc->dev->devno);

        if (!(qc->flags & ATA_QCFLAG_DMAMAP))
                return;

        table = (struct dbdma_cmd *) priv->dma_table_cpu;

        pi = 0;
        for_each_sg(qc->sg, sg, qc->n_elem, si) {
                u32 addr, sg_len, len;

                /* determine if physical DMA addr spans 64K boundary.
                 * Note h/w doesn't support 64-bit, so we unconditionally
                 * truncate dma_addr_t to u32.
                 */
                addr = (u32) sg_dma_address(sg);
                sg_len = sg_dma_len(sg);

                while (sg_len) {
                        /* table overflow should never happen */
                        BUG_ON (pi++ >= MAX_DCMDS);

                        len = (sg_len < MAX_DBDMA_SEG) ? sg_len : MAX_DBDMA_SEG;
                        table->command = cpu_to_le16(write ? OUTPUT_MORE: INPUT_MORE);
                        table->req_count = cpu_to_le16(len);
                        table->phy_addr = cpu_to_le32(addr);
                        table->cmd_dep = 0;
                        table->xfer_status = 0;
                        table->res_count = 0;
                        addr += len;
                        sg_len -= len;
                        ++table;
                }
        }

        /* Should never happen according to Tejun */
        BUG_ON(!pi);

        /* Convert the last command to an input/output */
        table--;
        table->command = cpu_to_le16(write ? OUTPUT_LAST: INPUT_LAST);
        table++;

        /* Add the stop command to the end of the list */
        memset(table, 0, sizeof(struct dbdma_cmd));
        table->command = cpu_to_le16(DBDMA_STOP);

        dev_dbgdma(priv->dev, "%s: %d DMA list entries\n", __func__, pi);
}


static void pata_macio_freeze(struct ata_port *ap)
{
        struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;

        if (dma_regs) {
                unsigned int timeout = 1000000;

                /* Make sure DMA controller is stopped */
                writel((RUN|PAUSE|FLUSH|WAKE|DEAD) << 16, &dma_regs->control);
                while (--timeout && (readl(&dma_regs->status) & RUN))
                        udelay(1);
        }

        ata_sff_freeze(ap);
}


static void pata_macio_bmdma_setup(struct ata_queued_cmd *qc)
{
        struct ata_port *ap = qc->ap;
        struct pata_macio_priv *priv = ap->private_data;
        struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
        int dev = qc->dev->devno;

        dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);

        /* Make sure DMA commands updates are visible */
        writel(priv->dma_table_dma, &dma_regs->cmdptr);

        /* On KeyLargo 66Mhz cell, we need to add 60ns to wrDataSetup on
         * UDMA reads
         */
        if (priv->kind == controller_kl_ata4 &&
            (priv->treg[dev][0] & TR_66_UDMA_EN)) {
                void __iomem *rbase = ap->ioaddr.cmd_addr;
                u32 reg = priv->treg[dev][0];

                if (!(qc->tf.flags & ATA_TFLAG_WRITE))
                        reg += 0x00800000;
                writel(reg, rbase + IDE_TIMING_CONFIG);
        }

        /* issue r/w command */
        ap->ops->sff_exec_command(ap, &qc->tf);
}

static void pata_macio_bmdma_start(struct ata_queued_cmd *qc)
{
        struct ata_port *ap = qc->ap;
        struct pata_macio_priv *priv = ap->private_data;
        struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;

        dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);

        writel((RUN << 16) | RUN, &dma_regs->control);
        /* Make sure it gets to the controller right now */
        (void)readl(&dma_regs->control);
}

static void pata_macio_bmdma_stop(struct ata_queued_cmd *qc)
{
        struct ata_port *ap = qc->ap;
        struct pata_macio_priv *priv = ap->private_data;
        struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
        unsigned int timeout = 1000000;

        dev_dbgdma(priv->dev, "%s: qc %p\n", __func__, qc);

        /* Stop the DMA engine and wait for it to full halt */
        writel (((RUN|WAKE|DEAD) << 16), &dma_regs->control);
        while (--timeout && (readl(&dma_regs->status) & RUN))
                udelay(1);
}

static u8 pata_macio_bmdma_status(struct ata_port *ap)
{
        struct pata_macio_priv *priv = ap->private_data;
        struct dbdma_regs __iomem *dma_regs = ap->ioaddr.bmdma_addr;
        u32 dstat, rstat = ATA_DMA_INTR;
        unsigned long timeout = 0;

        dstat = readl(&dma_regs->status);

        dev_dbgdma(priv->dev, "%s: dstat=%x\n", __func__, dstat);

        /* We have two things to deal with here:
         *
         * - The dbdma won't stop if the command was started
         * but completed with an error without transferring all
         * datas. This happens when bad blocks are met during
         * a multi-block transfer.
         *
         * - The dbdma fifo hasn't yet finished flushing to
         * to system memory when the disk interrupt occurs.
         *
         */

        /* First check for errors */
        if ((dstat & (RUN|DEAD)) != RUN)
                rstat |= ATA_DMA_ERR;

        /* If ACTIVE is cleared, the STOP command has been hit and
         * the transfer is complete. If not, we have to flush the
         * channel.
         */
        if ((dstat & ACTIVE) == 0)
                return rstat;

        dev_dbgdma(priv->dev, "%s: DMA still active, flushing...\n", __func__);

        /* If dbdma didn't execute the STOP command yet, the
         * active bit is still set. We consider that we aren't
         * sharing interrupts (which is hopefully the case with
         * those controllers) and so we just try to flush the
         * channel for pending data in the fifo
         */
        udelay(1);
        writel((FLUSH << 16) | FLUSH, &dma_regs->control);
        for (;;) {
                udelay(1);
                dstat = readl(&dma_regs->status);
                if ((dstat & FLUSH) == 0)
                        break;
                if (++timeout > 1000) {
                        dev_warn(priv->dev, "timeout flushing DMA\n");
                        rstat |= ATA_DMA_ERR;
                        break;
                }
        }
        return rstat;
}

/* port_start is when we allocate the DMA command list */
static int pata_macio_port_start(struct ata_port *ap)
{
        struct pata_macio_priv *priv = ap->private_data;

        if (ap->ioaddr.bmdma_addr == NULL)
                return 0;

        /* Allocate space for the DBDMA commands.
         *
         * The +2 is +1 for the stop command and +1 to allow for
         * aligning the start address to a multiple of 16 bytes.
         */
        priv->dma_table_cpu =
                dmam_alloc_coherent(priv->dev,
                                    (MAX_DCMDS + 2) * sizeof(struct dbdma_cmd),
                                    &priv->dma_table_dma, GFP_KERNEL);
        if (priv->dma_table_cpu == NULL) {
                dev_err(priv->dev, "Unable to allocate DMA command list\n");
                ap->ioaddr.bmdma_addr = NULL;
                ap->mwdma_mask = 0;
                ap->udma_mask = 0;
        }
        return 0;
}

static void pata_macio_irq_clear(struct ata_port *ap)
{
        struct pata_macio_priv *priv = ap->private_data;

        /* Nothing to do here */

        dev_dbgdma(priv->dev, "%s\n", __func__);
}

static void pata_macio_reset_hw(struct pata_macio_priv *priv, int resume)
{
        dev_dbg(priv->dev, "Enabling & resetting... \n");

        if (priv->mediabay)
                return;

        if (priv->kind == controller_ohare && !resume) {
                /* The code below is having trouble on some ohare machines
                 * (timing related ?). Until I can put my hand on one of these
                 * units, I keep the old way
                 */
                ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, priv->node, 0, 1);
        } else {
                int rc;

                /* Reset and enable controller */
                rc = ppc_md.feature_call(PMAC_FTR_IDE_RESET,
                                         priv->node, priv->aapl_bus_id, 1);
                ppc_md.feature_call(PMAC_FTR_IDE_ENABLE,
                                    priv->node, priv->aapl_bus_id, 1);
                msleep(10);
                /* Only bother waiting if there's a reset control */
                if (rc == 0) {
                        ppc_md.feature_call(PMAC_FTR_IDE_RESET,
                                            priv->node, priv->aapl_bus_id, 0);
                        msleep(IDE_WAKEUP_DELAY_MS);
                }
        }

        /* If resuming a PCI device, restore the config space here */
        if (priv->pdev && resume) {
                int rc;

                pci_restore_state(priv->pdev);
                rc = pcim_enable_device(priv->pdev);
                if (rc)
                        dev_err(&priv->pdev->dev,
                                "Failed to enable device after resume (%d)\n",
                                rc);
                else
                        pci_set_master(priv->pdev);
        }

        /* On Kauai, initialize the FCR. We don't perform a reset, doesn't really
         * seem necessary and speeds up the boot process
         */
        if (priv->kauai_fcr)
                writel(KAUAI_FCR_UATA_MAGIC |
                       KAUAI_FCR_UATA_RESET_N |
                       KAUAI_FCR_UATA_ENABLE, priv->kauai_fcr);
}

/* Hook the standard slave config to fixup some HW related alignment
 * restrictions
 */
static int pata_macio_slave_config(struct scsi_device *sdev)
{
        struct ata_port *ap = ata_shost_to_port(sdev->host);
        struct pata_macio_priv *priv = ap->private_data;
        struct ata_device *dev;
        u16 cmd;
        int rc;

        /* First call original */
        rc = ata_scsi_slave_config(sdev);
        if (rc)
                return rc;

        /* This is lifted from sata_nv */
        dev = &ap->link.device[sdev->id];

        /* OHare has issues with non cache aligned DMA on some chipsets */
        if (priv->kind == controller_ohare) {
                blk_queue_update_dma_alignment(sdev->request_queue, 31);
                blk_queue_update_dma_pad(sdev->request_queue, 31);

                /* Tell the world about it */
                ata_dev_info(dev, "OHare alignment limits applied\n");
                return 0;
        }

        /* We only have issues with ATAPI */
        if (dev->class != ATA_DEV_ATAPI)
                return 0;

        /* Shasta and K2 seem to have "issues" with reads ... */
        if (priv->kind == controller_sh_ata6 || priv->kind == controller_k2_ata6) {
                /* Allright these are bad, apply restrictions */
                blk_queue_update_dma_alignment(sdev->request_queue, 15);
                blk_queue_update_dma_pad(sdev->request_queue, 15);

                /* We enable MWI and hack cache line size directly here, this
                 * is specific to this chipset and not normal values, we happen
                 * to somewhat know what we are doing here (which is basically
                 * to do the same Apple does and pray they did not get it wrong :-)
                 */
                BUG_ON(!priv->pdev);
                pci_write_config_byte(priv->pdev, PCI_CACHE_LINE_SIZE, 0x08);
                pci_read_config_word(priv->pdev, PCI_COMMAND, &cmd);
                pci_write_config_word(priv->pdev, PCI_COMMAND,
                                      cmd | PCI_COMMAND_INVALIDATE);

                /* Tell the world about it */
                ata_dev_info(dev, "K2/Shasta alignment limits applied\n");
        }

        return 0;
}

#ifdef CONFIG_PM_SLEEP
static int pata_macio_do_suspend(struct pata_macio_priv *priv, pm_message_t mesg)
{
        int rc;

        /* First, core libata suspend to do most of the work */
        rc = ata_host_suspend(priv->host, mesg);
        if (rc)
                return rc;

        /* Restore to default timings */
        pata_macio_default_timings(priv);

        /* Mask interrupt. Not strictly necessary but old driver did
         * it and I'd rather not change that here */
        disable_irq(priv->irq);

        /* The media bay will handle itself just fine */
        if (priv->mediabay)
                return 0;

        /* Kauai has bus control FCRs directly here */
        if (priv->kauai_fcr) {
                u32 fcr = readl(priv->kauai_fcr);
                fcr &= ~(KAUAI_FCR_UATA_RESET_N | KAUAI_FCR_UATA_ENABLE);
                writel(fcr, priv->kauai_fcr);
        }

        /* For PCI, save state and disable DMA. No need to call
         * pci_set_power_state(), the HW doesn't do D states that
         * way, the platform code will take care of suspending the
         * ASIC properly
         */
        if (priv->pdev) {
                pci_save_state(priv->pdev);
                pci_disable_device(priv->pdev);
        }

        /* Disable the bus on older machines and the cell on kauai */
        ppc_md.feature_call(PMAC_FTR_IDE_ENABLE, priv->node,
                            priv->aapl_bus_id, 0);

        return 0;
}

static int pata_macio_do_resume(struct pata_macio_priv *priv)
{
        /* Reset and re-enable the HW */
        pata_macio_reset_hw(priv, 1);

        /* Sanitize drive timings */
        pata_macio_apply_timings(priv->host->ports[0], 0);

        /* We want our IRQ back ! */
        enable_irq(priv->irq);

        /* Let the libata core take it from there */
        ata_host_resume(priv->host);

        return 0;
}
#endif /* CONFIG_PM_SLEEP */

static struct scsi_host_template pata_macio_sht = {
        ATA_BASE_SHT(DRV_NAME),
        .sg_tablesize           = MAX_DCMDS,
        /* We may not need that strict one */
        .dma_boundary           = ATA_DMA_BOUNDARY,
        /* Not sure what the real max is but we know it's less than 64K, let's
         * use 64K minus 256
         */
        .max_segment_size       = MAX_DBDMA_SEG,
        .slave_configure        = pata_macio_slave_config,
};

static struct ata_port_operations pata_macio_ops = {
        .inherits               = &ata_bmdma_port_ops,

        .freeze                 = pata_macio_freeze,
        .set_piomode            = pata_macio_set_timings,
        .set_dmamode            = pata_macio_set_timings,
        .cable_detect           = pata_macio_cable_detect,
        .sff_dev_select         = pata_macio_dev_select,
        .qc_prep                = pata_macio_qc_prep,
        .bmdma_setup            = pata_macio_bmdma_setup,
        .bmdma_start            = pata_macio_bmdma_start,
        .bmdma_stop             = pata_macio_bmdma_stop,
        .bmdma_status           = pata_macio_bmdma_status,
        .port_start             = pata_macio_port_start,
        .sff_irq_clear          = pata_macio_irq_clear,
};

static void pata_macio_invariants(struct pata_macio_priv *priv)
{
        const int *bidp;

        /* Identify the type of controller */
        if (of_device_is_compatible(priv->node, "shasta-ata")) {
                priv->kind = controller_sh_ata6;
                priv->timings = pata_macio_shasta_timings;
        } else if (of_device_is_compatible(priv->node, "kauai-ata")) {
                priv->kind = controller_un_ata6;
                priv->timings = pata_macio_kauai_timings;
        } else if (of_device_is_compatible(priv->node, "K2-UATA")) {
                priv->kind = controller_k2_ata6;
                priv->timings = pata_macio_kauai_timings;
        } else if (of_device_is_compatible(priv->node, "keylargo-ata")) {
                if (of_node_name_eq(priv->node, "ata-4")) {
                        priv->kind = controller_kl_ata4;
                        priv->timings = pata_macio_kl66_timings;
                } else {
                        priv->kind = controller_kl_ata3;
                        priv->timings = pata_macio_kl33_timings;
                }
        } else if (of_device_is_compatible(priv->node, "heathrow-ata")) {
                priv->kind = controller_heathrow;
                priv->timings = pata_macio_heathrow_timings;
        } else {
                priv->kind = controller_ohare;
                priv->timings = pata_macio_ohare_timings;
        }

        /* XXX FIXME --- setup priv->mediabay here */

        /* Get Apple bus ID (for clock and ASIC control) */
        bidp = of_get_property(priv->node, "AAPL,bus-id", NULL);
        priv->aapl_bus_id =  bidp ? *bidp : 0;

        /* Fixup missing Apple bus ID in case of media-bay */
        if (priv->mediabay && bidp == 0)
                priv->aapl_bus_id = 1;
}

static void pata_macio_setup_ios(struct ata_ioports *ioaddr,
                                 void __iomem * base, void __iomem * dma)
{
        /* cmd_addr is the base of regs for that port */
        ioaddr->cmd_addr        = base;

        /* taskfile registers */
        ioaddr->data_addr       = base + (ATA_REG_DATA    << 4);
        ioaddr->error_addr      = base + (ATA_REG_ERR     << 4);
        ioaddr->feature_addr    = base + (ATA_REG_FEATURE << 4);
        ioaddr->nsect_addr      = base + (ATA_REG_NSECT   << 4);
        ioaddr->lbal_addr       = base + (ATA_REG_LBAL    << 4);
        ioaddr->lbam_addr       = base + (ATA_REG_LBAM    << 4);
        ioaddr->lbah_addr       = base + (ATA_REG_LBAH    << 4);
        ioaddr->device_addr     = base + (ATA_REG_DEVICE  << 4);
        ioaddr->status_addr     = base + (ATA_REG_STATUS  << 4);
        ioaddr->command_addr    = base + (ATA_REG_CMD     << 4);

        ioaddr->altstatus_addr  = base + 0x160;
        ioaddr->ctl_addr        = base + 0x160;
        ioaddr->bmdma_addr      = dma;
}

static void pmac_macio_calc_timing_masks(struct pata_macio_priv *priv,
                                         struct ata_port_info *pinfo)
{
        int i = 0;

        pinfo->pio_mask         = 0;
        pinfo->mwdma_mask       = 0;
        pinfo->udma_mask        = 0;

        while (priv->timings[i].mode > 0) {
                unsigned int mask = 1U << (priv->timings[i].mode & 0x0f);
                switch(priv->timings[i].mode & 0xf0) {
                case 0x00: /* PIO */
                        pinfo->pio_mask |= (mask >> 8);
                        break;
                case 0x20: /* MWDMA */
                        pinfo->mwdma_mask |= mask;
                        break;
                case 0x40: /* UDMA */
                        pinfo->udma_mask |= mask;
                        break;
                }
                i++;
        }
        dev_dbg(priv->dev, "Supported masks: PIO=%lx, MWDMA=%lx, UDMA=%lx\n",
                pinfo->pio_mask, pinfo->mwdma_mask, pinfo->udma_mask);
}

static int pata_macio_common_init(struct pata_macio_priv *priv,
                                  resource_size_t tfregs,
                                  resource_size_t dmaregs,
                                  resource_size_t fcregs,
                                  unsigned long irq)
{
        struct ata_port_info            pinfo;
        const struct ata_port_info      *ppi[] = { &pinfo, NULL };
        void __iomem                    *dma_regs = NULL;

        /* Fill up privates with various invariants collected from the
         * device-tree
         */
        pata_macio_invariants(priv);

        /* Make sure we have sane initial timings in the cache */
        pata_macio_default_timings(priv);

        /* Allocate libata host for 1 port */
        memset(&pinfo, 0, sizeof(struct ata_port_info));
        pmac_macio_calc_timing_masks(priv, &pinfo);
        pinfo.flags             = ATA_FLAG_SLAVE_POSS;
        pinfo.port_ops          = &pata_macio_ops;
        pinfo.private_data      = priv;

        priv->host = ata_host_alloc_pinfo(priv->dev, ppi, 1);
        if (priv->host == NULL) {
                dev_err(priv->dev, "Failed to allocate ATA port structure\n");
                return -ENOMEM;
        }

        /* Setup the private data in host too */
        priv->host->private_data = priv;

        /* Map base registers */
        priv->tfregs = devm_ioremap(priv->dev, tfregs, 0x100);
        if (priv->tfregs == NULL) {
                dev_err(priv->dev, "Failed to map ATA ports\n");
                return -ENOMEM;
        }
        priv->host->iomap = &priv->tfregs;

        /* Map DMA regs */
        if (dmaregs != 0) {
                dma_regs = devm_ioremap(priv->dev, dmaregs,
                                        sizeof(struct dbdma_regs));
                if (dma_regs == NULL)
                        dev_warn(priv->dev, "Failed to map ATA DMA registers\n");
        }

        /* If chip has local feature control, map those regs too */
        if (fcregs != 0) {
                priv->kauai_fcr = devm_ioremap(priv->dev, fcregs, 4);
                if (priv->kauai_fcr == NULL) {
                        dev_err(priv->dev, "Failed to map ATA FCR register\n");
                        return -ENOMEM;
                }
        }

        /* Setup port data structure */
        pata_macio_setup_ios(&priv->host->ports[0]->ioaddr,
                             priv->tfregs, dma_regs);
        priv->host->ports[0]->private_data = priv;

        /* hard-reset the controller */
        pata_macio_reset_hw(priv, 0);
        pata_macio_apply_timings(priv->host->ports[0], 0);

        /* Enable bus master if necessary */
        if (priv->pdev && dma_regs)
                pci_set_master(priv->pdev);

        dev_info(priv->dev, "Activating pata-macio chipset %s, Apple bus ID %d\n",
                 macio_ata_names[priv->kind], priv->aapl_bus_id);

        /* Start it up */
        priv->irq = irq;
        return ata_host_activate(priv->host, irq, ata_bmdma_interrupt, 0,
                                 &pata_macio_sht);
}

static int pata_macio_attach(struct macio_dev *mdev,
                             const struct of_device_id *match)
{
        struct pata_macio_priv  *priv;
        resource_size_t         tfregs, dmaregs = 0;
        unsigned long           irq;
        int                     rc;

        /* Check for broken device-trees */
        if (macio_resource_count(mdev) == 0) {
                dev_err(&mdev->ofdev.dev,
                        "No addresses for controller\n");
                return -ENXIO;
        }

        /* Enable managed resources */
        macio_enable_devres(mdev);

        /* Allocate and init private data structure */
        priv = devm_kzalloc(&mdev->ofdev.dev,
                            sizeof(struct pata_macio_priv), GFP_KERNEL);
        if (!priv)
                return -ENOMEM;

        priv->node = of_node_get(mdev->ofdev.dev.of_node);
        priv->mdev = mdev;
        priv->dev = &mdev->ofdev.dev;

        /* Request memory resource for taskfile registers */
        if (macio_request_resource(mdev, 0, "pata-macio")) {
                dev_err(&mdev->ofdev.dev,
                        "Cannot obtain taskfile resource\n");
                return -EBUSY;
        }
        tfregs = macio_resource_start(mdev, 0);

        /* Request resources for DMA registers if any */
        if (macio_resource_count(mdev) >= 2) {
                if (macio_request_resource(mdev, 1, "pata-macio-dma"))
                        dev_err(&mdev->ofdev.dev,
                                "Cannot obtain DMA resource\n");
                else
                        dmaregs = macio_resource_start(mdev, 1);
        }

        /*
         * Fixup missing IRQ for some old implementations with broken
         * device-trees.
         *
         * This is a bit bogus, it should be fixed in the device-tree itself,
         * via the existing macio fixups, based on the type of interrupt
         * controller in the machine. However, I have no test HW for this case,
         * and this trick works well enough on those old machines...
         */
        if (macio_irq_count(mdev) == 0) {
                dev_warn(&mdev->ofdev.dev,
                         "No interrupts for controller, using 13\n");
                irq = irq_create_mapping(NULL, 13);
        } else
                irq = macio_irq(mdev, 0);

        /* Prevvent media bay callbacks until fully registered */
        lock_media_bay(priv->mdev->media_bay);

        /* Get register addresses and call common initialization */
        rc = pata_macio_common_init(priv,
                                    tfregs,             /* Taskfile regs */
                                    dmaregs,            /* DBDMA regs */
                                    0,                  /* Feature control */
                                    irq);
        unlock_media_bay(priv->mdev->media_bay);

        return rc;
}

static int pata_macio_detach(struct macio_dev *mdev)
{
        struct ata_host *host = macio_get_drvdata(mdev);
        struct pata_macio_priv *priv = host->private_data;

        lock_media_bay(priv->mdev->media_bay);

        /* Make sure the mediabay callback doesn't try to access
         * dead stuff
         */
        priv->host->private_data = NULL;

        ata_host_detach(host);

        unlock_media_bay(priv->mdev->media_bay);

        return 0;
}

#ifdef CONFIG_PM_SLEEP
static int pata_macio_suspend(struct macio_dev *mdev, pm_message_t mesg)
{
        struct ata_host *host = macio_get_drvdata(mdev);

        return pata_macio_do_suspend(host->private_data, mesg);
}

static int pata_macio_resume(struct macio_dev *mdev)
{
        struct ata_host *host = macio_get_drvdata(mdev);

        return pata_macio_do_resume(host->private_data);
}
#endif /* CONFIG_PM_SLEEP */

#ifdef CONFIG_PMAC_MEDIABAY
static void pata_macio_mb_event(struct macio_dev* mdev, int mb_state)
{
        struct ata_host *host = macio_get_drvdata(mdev);
        struct ata_port *ap;
        struct ata_eh_info *ehi;
        struct ata_device *dev;
        unsigned long flags;

        if (!host || !host->private_data)
                return;
        ap = host->ports[0];
        spin_lock_irqsave(ap->lock, flags);
        ehi = &ap->link.eh_info;
        if (mb_state == MB_CD) {
                ata_ehi_push_desc(ehi, "mediabay plug");
                ata_ehi_hotplugged(ehi);
                ata_port_freeze(ap);
        } else {
                ata_ehi_push_desc(ehi, "mediabay unplug");
                ata_for_each_dev(dev, &ap->link, ALL)
                        dev->flags |= ATA_DFLAG_DETACH;
                ata_port_abort(ap);
        }
        spin_unlock_irqrestore(ap->lock, flags);

}
#endif /* CONFIG_PMAC_MEDIABAY */


static int pata_macio_pci_attach(struct pci_dev *pdev,
                                 const struct pci_device_id *id)
{
        struct pata_macio_priv  *priv;
        struct device_node      *np;
        resource_size_t         rbase;

        /* We cannot use a MacIO controller without its OF device node */
        np = pci_device_to_OF_node(pdev);
        if (np == NULL) {
                dev_err(&pdev->dev,
                        "Cannot find OF device node for controller\n");
                return -ENODEV;
        }

        /* Check that it can be enabled */
        if (pcim_enable_device(pdev)) {
                dev_err(&pdev->dev,
                        "Cannot enable controller PCI device\n");
                return -ENXIO;
        }

        /* Allocate and init private data structure */
        priv = devm_kzalloc(&pdev->dev,
                            sizeof(struct pata_macio_priv), GFP_KERNEL);
        if (!priv)
                return -ENOMEM;

        priv->node = of_node_get(np);
        priv->pdev = pdev;
        priv->dev = &pdev->dev;

        /* Get MMIO regions */
        if (pci_request_regions(pdev, "pata-macio")) {
                dev_err(&pdev->dev,
                        "Cannot obtain PCI resources\n");
                return -EBUSY;
        }

        /* Get register addresses and call common initialization */
        rbase = pci_resource_start(pdev, 0);
        if (pata_macio_common_init(priv,
                                   rbase + 0x2000,      /* Taskfile regs */
                                   rbase + 0x1000,      /* DBDMA regs */
                                   rbase,               /* Feature control */
                                   pdev->irq))
                return -ENXIO;

        return 0;
}

static void pata_macio_pci_detach(struct pci_dev *pdev)
{
        struct ata_host *host = pci_get_drvdata(pdev);

        ata_host_detach(host);
}

#ifdef CONFIG_PM_SLEEP
static int pata_macio_pci_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
        struct ata_host *host = pci_get_drvdata(pdev);

        return pata_macio_do_suspend(host->private_data, mesg);
}

static int pata_macio_pci_resume(struct pci_dev *pdev)
{
        struct ata_host *host = pci_get_drvdata(pdev);

        return pata_macio_do_resume(host->private_data);
}
#endif /* CONFIG_PM_SLEEP */

static const struct of_device_id pata_macio_match[] =
{
        {
        .name           = "IDE",
        },
        {
        .name           = "ATA",
        },
        {
        .type           = "ide",
        },
        {
        .type           = "ata",
        },
        {},
};
MODULE_DEVICE_TABLE(of, pata_macio_match);

static struct macio_driver pata_macio_driver =
{
        .driver = {
                .name           = "pata-macio",
                .owner          = THIS_MODULE,
                .of_match_table = pata_macio_match,
        },
        .probe          = pata_macio_attach,
        .remove         = pata_macio_detach,
#ifdef CONFIG_PM_SLEEP
        .suspend        = pata_macio_suspend,
        .resume         = pata_macio_resume,
#endif
#ifdef CONFIG_PMAC_MEDIABAY
        .mediabay_event = pata_macio_mb_event,
#endif
};

static const struct pci_device_id pata_macio_pci_match[] = {
        { PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_UNI_N_ATA),    0 },
        { PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_IPID_ATA100),  0 },
        { PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_K2_ATA100),    0 },
        { PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_SH_ATA),       0 },
        { PCI_VDEVICE(APPLE, PCI_DEVICE_ID_APPLE_IPID2_ATA),    0 },
        {},
};

static struct pci_driver pata_macio_pci_driver = {
        .name           = "pata-pci-macio",
        .id_table       = pata_macio_pci_match,
        .probe          = pata_macio_pci_attach,
        .remove         = pata_macio_pci_detach,
#ifdef CONFIG_PM_SLEEP
        .suspend        = pata_macio_pci_suspend,
        .resume         = pata_macio_pci_resume,
#endif
        .driver = {
                .owner          = THIS_MODULE,
        },
};
MODULE_DEVICE_TABLE(pci, pata_macio_pci_match);


static int __init pata_macio_init(void)
{
        int rc;

        if (!machine_is(powermac))
                return -ENODEV;

        rc = pci_register_driver(&pata_macio_pci_driver);
        if (rc)
                return rc;
        rc = macio_register_driver(&pata_macio_driver);
        if (rc) {
                pci_unregister_driver(&pata_macio_pci_driver);
                return rc;
        }
        return 0;
}

static void __exit pata_macio_exit(void)
{
        macio_unregister_driver(&pata_macio_driver);
        pci_unregister_driver(&pata_macio_pci_driver);
}

module_init(pata_macio_init);
module_exit(pata_macio_exit);

MODULE_AUTHOR("Benjamin Herrenschmidt");
MODULE_DESCRIPTION("Apple MacIO PATA driver");
MODULE_LICENSE("GPL");
MODULE_VERSION(DRV_VERSION);