linux/drivers/ata/sata_dwc_460ex.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0-or-later
   2/*
   3 * drivers/ata/sata_dwc_460ex.c
   4 *
   5 * Synopsys DesignWare Cores (DWC) SATA host driver
   6 *
   7 * Author: Mark Miesfeld <mmiesfeld@amcc.com>
   8 *
   9 * Ported from 2.6.19.2 to 2.6.25/26 by Stefan Roese <sr@denx.de>
  10 * Copyright 2008 DENX Software Engineering
  11 *
  12 * Based on versions provided by AMCC and Synopsys which are:
  13 *          Copyright 2006 Applied Micro Circuits Corporation
  14 *          COPYRIGHT (C) 2005  SYNOPSYS, INC.  ALL RIGHTS RESERVED
  15 */
  16
  17#ifdef CONFIG_SATA_DWC_DEBUG
  18#define DEBUG
  19#endif
  20
  21#ifdef CONFIG_SATA_DWC_VDEBUG
  22#define VERBOSE_DEBUG
  23#define DEBUG_NCQ
  24#endif
  25
  26#include <linux/kernel.h>
  27#include <linux/module.h>
  28#include <linux/device.h>
  29#include <linux/dmaengine.h>
  30#include <linux/of_address.h>
  31#include <linux/of_irq.h>
  32#include <linux/of_platform.h>
  33#include <linux/platform_device.h>
  34#include <linux/phy/phy.h>
  35#include <linux/libata.h>
  36#include <linux/slab.h>
  37
  38#include "libata.h"
  39
  40#include <scsi/scsi_host.h>
  41#include <scsi/scsi_cmnd.h>
  42
  43/* These two are defined in "libata.h" */
  44#undef  DRV_NAME
  45#undef  DRV_VERSION
  46
  47#define DRV_NAME        "sata-dwc"
  48#define DRV_VERSION     "1.3"
  49
  50#define sata_dwc_writel(a, v)   writel_relaxed(v, a)
  51#define sata_dwc_readl(a)       readl_relaxed(a)
  52
  53#ifndef NO_IRQ
  54#define NO_IRQ          0
  55#endif
  56
  57#define AHB_DMA_BRST_DFLT       64      /* 16 data items burst length */
  58
  59enum {
  60        SATA_DWC_MAX_PORTS = 1,
  61
  62        SATA_DWC_SCR_OFFSET = 0x24,
  63        SATA_DWC_REG_OFFSET = 0x64,
  64};
  65
  66/* DWC SATA Registers */
  67struct sata_dwc_regs {
  68        u32 fptagr;             /* 1st party DMA tag */
  69        u32 fpbor;              /* 1st party DMA buffer offset */
  70        u32 fptcr;              /* 1st party DMA Xfr count */
  71        u32 dmacr;              /* DMA Control */
  72        u32 dbtsr;              /* DMA Burst Transac size */
  73        u32 intpr;              /* Interrupt Pending */
  74        u32 intmr;              /* Interrupt Mask */
  75        u32 errmr;              /* Error Mask */
  76        u32 llcr;               /* Link Layer Control */
  77        u32 phycr;              /* PHY Control */
  78        u32 physr;              /* PHY Status */
  79        u32 rxbistpd;           /* Recvd BIST pattern def register */
  80        u32 rxbistpd1;          /* Recvd BIST data dword1 */
  81        u32 rxbistpd2;          /* Recvd BIST pattern data dword2 */
  82        u32 txbistpd;           /* Trans BIST pattern def register */
  83        u32 txbistpd1;          /* Trans BIST data dword1 */
  84        u32 txbistpd2;          /* Trans BIST data dword2 */
  85        u32 bistcr;             /* BIST Control Register */
  86        u32 bistfctr;           /* BIST FIS Count Register */
  87        u32 bistsr;             /* BIST Status Register */
  88        u32 bistdecr;           /* BIST Dword Error count register */
  89        u32 res[15];            /* Reserved locations */
  90        u32 testr;              /* Test Register */
  91        u32 versionr;           /* Version Register */
  92        u32 idr;                /* ID Register */
  93        u32 unimpl[192];        /* Unimplemented */
  94        u32 dmadr[256];         /* FIFO Locations in DMA Mode */
  95};
  96
  97enum {
  98        SCR_SCONTROL_DET_ENABLE =       0x00000001,
  99        SCR_SSTATUS_DET_PRESENT =       0x00000001,
 100        SCR_SERROR_DIAG_X       =       0x04000000,
 101/* DWC SATA Register Operations */
 102        SATA_DWC_TXFIFO_DEPTH   =       0x01FF,
 103        SATA_DWC_RXFIFO_DEPTH   =       0x01FF,
 104        SATA_DWC_DMACR_TMOD_TXCHEN =    0x00000004,
 105        SATA_DWC_DMACR_TXCHEN   = (0x00000001 | SATA_DWC_DMACR_TMOD_TXCHEN),
 106        SATA_DWC_DMACR_RXCHEN   = (0x00000002 | SATA_DWC_DMACR_TMOD_TXCHEN),
 107        SATA_DWC_DMACR_TXRXCH_CLEAR =   SATA_DWC_DMACR_TMOD_TXCHEN,
 108        SATA_DWC_INTPR_DMAT     =       0x00000001,
 109        SATA_DWC_INTPR_NEWFP    =       0x00000002,
 110        SATA_DWC_INTPR_PMABRT   =       0x00000004,
 111        SATA_DWC_INTPR_ERR      =       0x00000008,
 112        SATA_DWC_INTPR_NEWBIST  =       0x00000010,
 113        SATA_DWC_INTPR_IPF      =       0x10000000,
 114        SATA_DWC_INTMR_DMATM    =       0x00000001,
 115        SATA_DWC_INTMR_NEWFPM   =       0x00000002,
 116        SATA_DWC_INTMR_PMABRTM  =       0x00000004,
 117        SATA_DWC_INTMR_ERRM     =       0x00000008,
 118        SATA_DWC_INTMR_NEWBISTM =       0x00000010,
 119        SATA_DWC_LLCR_SCRAMEN   =       0x00000001,
 120        SATA_DWC_LLCR_DESCRAMEN =       0x00000002,
 121        SATA_DWC_LLCR_RPDEN     =       0x00000004,
 122/* This is all error bits, zero's are reserved fields. */
 123        SATA_DWC_SERROR_ERR_BITS =      0x0FFF0F03
 124};
 125
 126#define SATA_DWC_SCR0_SPD_GET(v)        (((v) >> 4) & 0x0000000F)
 127#define SATA_DWC_DMACR_TX_CLEAR(v)      (((v) & ~SATA_DWC_DMACR_TXCHEN) |\
 128                                                 SATA_DWC_DMACR_TMOD_TXCHEN)
 129#define SATA_DWC_DMACR_RX_CLEAR(v)      (((v) & ~SATA_DWC_DMACR_RXCHEN) |\
 130                                                 SATA_DWC_DMACR_TMOD_TXCHEN)
 131#define SATA_DWC_DBTSR_MWR(size)        (((size)/4) & SATA_DWC_TXFIFO_DEPTH)
 132#define SATA_DWC_DBTSR_MRD(size)        ((((size)/4) & SATA_DWC_RXFIFO_DEPTH)\
 133                                                 << 16)
 134struct sata_dwc_device {
 135        struct device           *dev;           /* generic device struct */
 136        struct ata_probe_ent    *pe;            /* ptr to probe-ent */
 137        struct ata_host         *host;
 138        struct sata_dwc_regs __iomem *sata_dwc_regs;    /* DW SATA specific */
 139        u32                     sactive_issued;
 140        u32                     sactive_queued;
 141        struct phy              *phy;
 142        phys_addr_t             dmadr;
 143#ifdef CONFIG_SATA_DWC_OLD_DMA
 144        struct dw_dma_chip      *dma;
 145#endif
 146};
 147
 148#define SATA_DWC_QCMD_MAX       32
 149
 150struct sata_dwc_device_port {
 151        struct sata_dwc_device  *hsdev;
 152        int                     cmd_issued[SATA_DWC_QCMD_MAX];
 153        int                     dma_pending[SATA_DWC_QCMD_MAX];
 154
 155        /* DMA info */
 156        struct dma_chan                 *chan;
 157        struct dma_async_tx_descriptor  *desc[SATA_DWC_QCMD_MAX];
 158        u32                             dma_interrupt_count;
 159};
 160
 161/*
 162 * Commonly used DWC SATA driver macros
 163 */
 164#define HSDEV_FROM_HOST(host)   ((struct sata_dwc_device *)(host)->private_data)
 165#define HSDEV_FROM_AP(ap)       ((struct sata_dwc_device *)(ap)->host->private_data)
 166#define HSDEVP_FROM_AP(ap)      ((struct sata_dwc_device_port *)(ap)->private_data)
 167#define HSDEV_FROM_QC(qc)       ((struct sata_dwc_device *)(qc)->ap->host->private_data)
 168#define HSDEV_FROM_HSDEVP(p)    ((struct sata_dwc_device *)(p)->hsdev)
 169
 170enum {
 171        SATA_DWC_CMD_ISSUED_NOT         = 0,
 172        SATA_DWC_CMD_ISSUED_PEND        = 1,
 173        SATA_DWC_CMD_ISSUED_EXEC        = 2,
 174        SATA_DWC_CMD_ISSUED_NODATA      = 3,
 175
 176        SATA_DWC_DMA_PENDING_NONE       = 0,
 177        SATA_DWC_DMA_PENDING_TX         = 1,
 178        SATA_DWC_DMA_PENDING_RX         = 2,
 179};
 180
 181/*
 182 * Prototypes
 183 */
 184static void sata_dwc_bmdma_start_by_tag(struct ata_queued_cmd *qc, u8 tag);
 185static int sata_dwc_qc_complete(struct ata_port *ap, struct ata_queued_cmd *qc,
 186                                u32 check_status);
 187static void sata_dwc_dma_xfer_complete(struct ata_port *ap, u32 check_status);
 188static void sata_dwc_port_stop(struct ata_port *ap);
 189static void sata_dwc_clear_dmacr(struct sata_dwc_device_port *hsdevp, u8 tag);
 190
 191#ifdef CONFIG_SATA_DWC_OLD_DMA
 192
 193#include <linux/platform_data/dma-dw.h>
 194#include <linux/dma/dw.h>
 195
 196static struct dw_dma_slave sata_dwc_dma_dws = {
 197        .src_id = 0,
 198        .dst_id = 0,
 199        .m_master = 1,
 200        .p_master = 0,
 201};
 202
 203static bool sata_dwc_dma_filter(struct dma_chan *chan, void *param)
 204{
 205        struct dw_dma_slave *dws = &sata_dwc_dma_dws;
 206
 207        if (dws->dma_dev != chan->device->dev)
 208                return false;
 209
 210        chan->private = dws;
 211        return true;
 212}
 213
 214static int sata_dwc_dma_get_channel_old(struct sata_dwc_device_port *hsdevp)
 215{
 216        struct sata_dwc_device *hsdev = hsdevp->hsdev;
 217        struct dw_dma_slave *dws = &sata_dwc_dma_dws;
 218        dma_cap_mask_t mask;
 219
 220        dws->dma_dev = hsdev->dev;
 221
 222        dma_cap_zero(mask);
 223        dma_cap_set(DMA_SLAVE, mask);
 224
 225        /* Acquire DMA channel */
 226        hsdevp->chan = dma_request_channel(mask, sata_dwc_dma_filter, hsdevp);
 227        if (!hsdevp->chan) {
 228                dev_err(hsdev->dev, "%s: dma channel unavailable\n",
 229                         __func__);
 230                return -EAGAIN;
 231        }
 232
 233        return 0;
 234}
 235
 236static int sata_dwc_dma_init_old(struct platform_device *pdev,
 237                                 struct sata_dwc_device *hsdev)
 238{
 239        struct device_node *np = pdev->dev.of_node;
 240        struct resource *res;
 241
 242        hsdev->dma = devm_kzalloc(&pdev->dev, sizeof(*hsdev->dma), GFP_KERNEL);
 243        if (!hsdev->dma)
 244                return -ENOMEM;
 245
 246        hsdev->dma->dev = &pdev->dev;
 247        hsdev->dma->id = pdev->id;
 248
 249        /* Get SATA DMA interrupt number */
 250        hsdev->dma->irq = irq_of_parse_and_map(np, 1);
 251        if (hsdev->dma->irq == NO_IRQ) {
 252                dev_err(&pdev->dev, "no SATA DMA irq\n");
 253                return -ENODEV;
 254        }
 255
 256        /* Get physical SATA DMA register base address */
 257        res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
 258        hsdev->dma->regs = devm_ioremap_resource(&pdev->dev, res);
 259        if (IS_ERR(hsdev->dma->regs))
 260                return PTR_ERR(hsdev->dma->regs);
 261
 262        /* Initialize AHB DMAC */
 263        return dw_dma_probe(hsdev->dma);
 264}
 265
 266static void sata_dwc_dma_exit_old(struct sata_dwc_device *hsdev)
 267{
 268        if (!hsdev->dma)
 269                return;
 270
 271        dw_dma_remove(hsdev->dma);
 272}
 273
 274#endif
 275
 276static const char *get_prot_descript(u8 protocol)
 277{
 278        switch (protocol) {
 279        case ATA_PROT_NODATA:
 280                return "ATA no data";
 281        case ATA_PROT_PIO:
 282                return "ATA PIO";
 283        case ATA_PROT_DMA:
 284                return "ATA DMA";
 285        case ATA_PROT_NCQ:
 286                return "ATA NCQ";
 287        case ATA_PROT_NCQ_NODATA:
 288                return "ATA NCQ no data";
 289        case ATAPI_PROT_NODATA:
 290                return "ATAPI no data";
 291        case ATAPI_PROT_PIO:
 292                return "ATAPI PIO";
 293        case ATAPI_PROT_DMA:
 294                return "ATAPI DMA";
 295        default:
 296                return "unknown";
 297        }
 298}
 299
 300static const char *get_dma_dir_descript(int dma_dir)
 301{
 302        switch ((enum dma_data_direction)dma_dir) {
 303        case DMA_BIDIRECTIONAL:
 304                return "bidirectional";
 305        case DMA_TO_DEVICE:
 306                return "to device";
 307        case DMA_FROM_DEVICE:
 308                return "from device";
 309        default:
 310                return "none";
 311        }
 312}
 313
 314static void sata_dwc_tf_dump(struct ata_port *ap, struct ata_taskfile *tf)
 315{
 316        dev_vdbg(ap->dev,
 317                "taskfile cmd: 0x%02x protocol: %s flags: 0x%lx device: %x\n",
 318                tf->command, get_prot_descript(tf->protocol), tf->flags,
 319                tf->device);
 320        dev_vdbg(ap->dev,
 321                "feature: 0x%02x nsect: 0x%x lbal: 0x%x lbam: 0x%x lbah: 0x%x\n",
 322                tf->feature, tf->nsect, tf->lbal, tf->lbam, tf->lbah);
 323        dev_vdbg(ap->dev,
 324                "hob_feature: 0x%02x hob_nsect: 0x%x hob_lbal: 0x%x hob_lbam: 0x%x hob_lbah: 0x%x\n",
 325                tf->hob_feature, tf->hob_nsect, tf->hob_lbal, tf->hob_lbam,
 326                tf->hob_lbah);
 327}
 328
 329static void dma_dwc_xfer_done(void *hsdev_instance)
 330{
 331        unsigned long flags;
 332        struct sata_dwc_device *hsdev = hsdev_instance;
 333        struct ata_host *host = (struct ata_host *)hsdev->host;
 334        struct ata_port *ap;
 335        struct sata_dwc_device_port *hsdevp;
 336        u8 tag = 0;
 337        unsigned int port = 0;
 338
 339        spin_lock_irqsave(&host->lock, flags);
 340        ap = host->ports[port];
 341        hsdevp = HSDEVP_FROM_AP(ap);
 342        tag = ap->link.active_tag;
 343
 344        /*
 345         * Each DMA command produces 2 interrupts.  Only
 346         * complete the command after both interrupts have been
 347         * seen. (See sata_dwc_isr())
 348         */
 349        hsdevp->dma_interrupt_count++;
 350        sata_dwc_clear_dmacr(hsdevp, tag);
 351
 352        if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_NONE) {
 353                dev_err(ap->dev, "DMA not pending tag=0x%02x pending=%d\n",
 354                        tag, hsdevp->dma_pending[tag]);
 355        }
 356
 357        if ((hsdevp->dma_interrupt_count % 2) == 0)
 358                sata_dwc_dma_xfer_complete(ap, 1);
 359
 360        spin_unlock_irqrestore(&host->lock, flags);
 361}
 362
 363static struct dma_async_tx_descriptor *dma_dwc_xfer_setup(struct ata_queued_cmd *qc)
 364{
 365        struct ata_port *ap = qc->ap;
 366        struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
 367        struct sata_dwc_device *hsdev = HSDEV_FROM_AP(ap);
 368        struct dma_slave_config sconf;
 369        struct dma_async_tx_descriptor *desc;
 370
 371        if (qc->dma_dir == DMA_DEV_TO_MEM) {
 372                sconf.src_addr = hsdev->dmadr;
 373                sconf.device_fc = false;
 374        } else {        /* DMA_MEM_TO_DEV */
 375                sconf.dst_addr = hsdev->dmadr;
 376                sconf.device_fc = false;
 377        }
 378
 379        sconf.direction = qc->dma_dir;
 380        sconf.src_maxburst = AHB_DMA_BRST_DFLT / 4;     /* in items */
 381        sconf.dst_maxburst = AHB_DMA_BRST_DFLT / 4;     /* in items */
 382        sconf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
 383        sconf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
 384
 385        dmaengine_slave_config(hsdevp->chan, &sconf);
 386
 387        /* Convert SG list to linked list of items (LLIs) for AHB DMA */
 388        desc = dmaengine_prep_slave_sg(hsdevp->chan, qc->sg, qc->n_elem,
 389                                       qc->dma_dir,
 390                                       DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
 391
 392        if (!desc)
 393                return NULL;
 394
 395        desc->callback = dma_dwc_xfer_done;
 396        desc->callback_param = hsdev;
 397
 398        dev_dbg(hsdev->dev, "%s sg: 0x%p, count: %d addr: %pa\n", __func__,
 399                qc->sg, qc->n_elem, &hsdev->dmadr);
 400
 401        return desc;
 402}
 403
 404static int sata_dwc_scr_read(struct ata_link *link, unsigned int scr, u32 *val)
 405{
 406        if (scr > SCR_NOTIFICATION) {
 407                dev_err(link->ap->dev, "%s: Incorrect SCR offset 0x%02x\n",
 408                        __func__, scr);
 409                return -EINVAL;
 410        }
 411
 412        *val = sata_dwc_readl(link->ap->ioaddr.scr_addr + (scr * 4));
 413        dev_dbg(link->ap->dev, "%s: id=%d reg=%d val=0x%08x\n", __func__,
 414                link->ap->print_id, scr, *val);
 415
 416        return 0;
 417}
 418
 419static int sata_dwc_scr_write(struct ata_link *link, unsigned int scr, u32 val)
 420{
 421        dev_dbg(link->ap->dev, "%s: id=%d reg=%d val=0x%08x\n", __func__,
 422                link->ap->print_id, scr, val);
 423        if (scr > SCR_NOTIFICATION) {
 424                dev_err(link->ap->dev, "%s: Incorrect SCR offset 0x%02x\n",
 425                         __func__, scr);
 426                return -EINVAL;
 427        }
 428        sata_dwc_writel(link->ap->ioaddr.scr_addr + (scr * 4), val);
 429
 430        return 0;
 431}
 432
 433static void clear_serror(struct ata_port *ap)
 434{
 435        u32 val;
 436        sata_dwc_scr_read(&ap->link, SCR_ERROR, &val);
 437        sata_dwc_scr_write(&ap->link, SCR_ERROR, val);
 438}
 439
 440static void clear_interrupt_bit(struct sata_dwc_device *hsdev, u32 bit)
 441{
 442        sata_dwc_writel(&hsdev->sata_dwc_regs->intpr,
 443                        sata_dwc_readl(&hsdev->sata_dwc_regs->intpr));
 444}
 445
 446static u32 qcmd_tag_to_mask(u8 tag)
 447{
 448        return 0x00000001 << (tag & 0x1f);
 449}
 450
 451/* See ahci.c */
 452static void sata_dwc_error_intr(struct ata_port *ap,
 453                                struct sata_dwc_device *hsdev, uint intpr)
 454{
 455        struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
 456        struct ata_eh_info *ehi = &ap->link.eh_info;
 457        unsigned int err_mask = 0, action = 0;
 458        struct ata_queued_cmd *qc;
 459        u32 serror;
 460        u8 status, tag;
 461
 462        ata_ehi_clear_desc(ehi);
 463
 464        sata_dwc_scr_read(&ap->link, SCR_ERROR, &serror);
 465        status = ap->ops->sff_check_status(ap);
 466
 467        tag = ap->link.active_tag;
 468
 469        dev_err(ap->dev,
 470                "%s SCR_ERROR=0x%08x intpr=0x%08x status=0x%08x dma_intp=%d pending=%d issued=%d",
 471                __func__, serror, intpr, status, hsdevp->dma_interrupt_count,
 472                hsdevp->dma_pending[tag], hsdevp->cmd_issued[tag]);
 473
 474        /* Clear error register and interrupt bit */
 475        clear_serror(ap);
 476        clear_interrupt_bit(hsdev, SATA_DWC_INTPR_ERR);
 477
 478        /* This is the only error happening now.  TODO check for exact error */
 479
 480        err_mask |= AC_ERR_HOST_BUS;
 481        action |= ATA_EH_RESET;
 482
 483        /* Pass this on to EH */
 484        ehi->serror |= serror;
 485        ehi->action |= action;
 486
 487        qc = ata_qc_from_tag(ap, tag);
 488        if (qc)
 489                qc->err_mask |= err_mask;
 490        else
 491                ehi->err_mask |= err_mask;
 492
 493        ata_port_abort(ap);
 494}
 495
 496/*
 497 * Function : sata_dwc_isr
 498 * arguments : irq, void *dev_instance, struct pt_regs *regs
 499 * Return value : irqreturn_t - status of IRQ
 500 * This Interrupt handler called via port ops registered function.
 501 * .irq_handler = sata_dwc_isr
 502 */
 503static irqreturn_t sata_dwc_isr(int irq, void *dev_instance)
 504{
 505        struct ata_host *host = (struct ata_host *)dev_instance;
 506        struct sata_dwc_device *hsdev = HSDEV_FROM_HOST(host);
 507        struct ata_port *ap;
 508        struct ata_queued_cmd *qc;
 509        unsigned long flags;
 510        u8 status, tag;
 511        int handled, num_processed, port = 0;
 512        uint intpr, sactive, sactive2, tag_mask;
 513        struct sata_dwc_device_port *hsdevp;
 514        hsdev->sactive_issued = 0;
 515
 516        spin_lock_irqsave(&host->lock, flags);
 517
 518        /* Read the interrupt register */
 519        intpr = sata_dwc_readl(&hsdev->sata_dwc_regs->intpr);
 520
 521        ap = host->ports[port];
 522        hsdevp = HSDEVP_FROM_AP(ap);
 523
 524        dev_dbg(ap->dev, "%s intpr=0x%08x active_tag=%d\n", __func__, intpr,
 525                ap->link.active_tag);
 526
 527        /* Check for error interrupt */
 528        if (intpr & SATA_DWC_INTPR_ERR) {
 529                sata_dwc_error_intr(ap, hsdev, intpr);
 530                handled = 1;
 531                goto DONE;
 532        }
 533
 534        /* Check for DMA SETUP FIS (FP DMA) interrupt */
 535        if (intpr & SATA_DWC_INTPR_NEWFP) {
 536                clear_interrupt_bit(hsdev, SATA_DWC_INTPR_NEWFP);
 537
 538                tag = (u8)(sata_dwc_readl(&hsdev->sata_dwc_regs->fptagr));
 539                dev_dbg(ap->dev, "%s: NEWFP tag=%d\n", __func__, tag);
 540                if (hsdevp->cmd_issued[tag] != SATA_DWC_CMD_ISSUED_PEND)
 541                        dev_warn(ap->dev, "CMD tag=%d not pending?\n", tag);
 542
 543                hsdev->sactive_issued |= qcmd_tag_to_mask(tag);
 544
 545                qc = ata_qc_from_tag(ap, tag);
 546                /*
 547                 * Start FP DMA for NCQ command.  At this point the tag is the
 548                 * active tag.  It is the tag that matches the command about to
 549                 * be completed.
 550                 */
 551                qc->ap->link.active_tag = tag;
 552                sata_dwc_bmdma_start_by_tag(qc, tag);
 553
 554                handled = 1;
 555                goto DONE;
 556        }
 557        sata_dwc_scr_read(&ap->link, SCR_ACTIVE, &sactive);
 558        tag_mask = (hsdev->sactive_issued | sactive) ^ sactive;
 559
 560        /* If no sactive issued and tag_mask is zero then this is not NCQ */
 561        if (hsdev->sactive_issued == 0 && tag_mask == 0) {
 562                if (ap->link.active_tag == ATA_TAG_POISON)
 563                        tag = 0;
 564                else
 565                        tag = ap->link.active_tag;
 566                qc = ata_qc_from_tag(ap, tag);
 567
 568                /* DEV interrupt w/ no active qc? */
 569                if (unlikely(!qc || (qc->tf.flags & ATA_TFLAG_POLLING))) {
 570                        dev_err(ap->dev,
 571                                "%s interrupt with no active qc qc=%p\n",
 572                                __func__, qc);
 573                        ap->ops->sff_check_status(ap);
 574                        handled = 1;
 575                        goto DONE;
 576                }
 577                status = ap->ops->sff_check_status(ap);
 578
 579                qc->ap->link.active_tag = tag;
 580                hsdevp->cmd_issued[tag] = SATA_DWC_CMD_ISSUED_NOT;
 581
 582                if (status & ATA_ERR) {
 583                        dev_dbg(ap->dev, "interrupt ATA_ERR (0x%x)\n", status);
 584                        sata_dwc_qc_complete(ap, qc, 1);
 585                        handled = 1;
 586                        goto DONE;
 587                }
 588
 589                dev_dbg(ap->dev, "%s non-NCQ cmd interrupt, protocol: %s\n",
 590                        __func__, get_prot_descript(qc->tf.protocol));
 591DRVSTILLBUSY:
 592                if (ata_is_dma(qc->tf.protocol)) {
 593                        /*
 594                         * Each DMA transaction produces 2 interrupts. The DMAC
 595                         * transfer complete interrupt and the SATA controller
 596                         * operation done interrupt. The command should be
 597                         * completed only after both interrupts are seen.
 598                         */
 599                        hsdevp->dma_interrupt_count++;
 600                        if (hsdevp->dma_pending[tag] == \
 601                                        SATA_DWC_DMA_PENDING_NONE) {
 602                                dev_err(ap->dev,
 603                                        "%s: DMA not pending intpr=0x%08x status=0x%08x pending=%d\n",
 604                                        __func__, intpr, status,
 605                                        hsdevp->dma_pending[tag]);
 606                        }
 607
 608                        if ((hsdevp->dma_interrupt_count % 2) == 0)
 609                                sata_dwc_dma_xfer_complete(ap, 1);
 610                } else if (ata_is_pio(qc->tf.protocol)) {
 611                        ata_sff_hsm_move(ap, qc, status, 0);
 612                        handled = 1;
 613                        goto DONE;
 614                } else {
 615                        if (unlikely(sata_dwc_qc_complete(ap, qc, 1)))
 616                                goto DRVSTILLBUSY;
 617                }
 618
 619                handled = 1;
 620                goto DONE;
 621        }
 622
 623        /*
 624         * This is a NCQ command. At this point we need to figure out for which
 625         * tags we have gotten a completion interrupt.  One interrupt may serve
 626         * as completion for more than one operation when commands are queued
 627         * (NCQ).  We need to process each completed command.
 628         */
 629
 630         /* process completed commands */
 631        sata_dwc_scr_read(&ap->link, SCR_ACTIVE, &sactive);
 632        tag_mask = (hsdev->sactive_issued | sactive) ^ sactive;
 633
 634        if (sactive != 0 || hsdev->sactive_issued > 1 || tag_mask > 1) {
 635                dev_dbg(ap->dev,
 636                        "%s NCQ:sactive=0x%08x  sactive_issued=0x%08x tag_mask=0x%08x\n",
 637                        __func__, sactive, hsdev->sactive_issued, tag_mask);
 638        }
 639
 640        if ((tag_mask | hsdev->sactive_issued) != hsdev->sactive_issued) {
 641                dev_warn(ap->dev,
 642                         "Bad tag mask?  sactive=0x%08x sactive_issued=0x%08x  tag_mask=0x%08x\n",
 643                         sactive, hsdev->sactive_issued, tag_mask);
 644        }
 645
 646        /* read just to clear ... not bad if currently still busy */
 647        status = ap->ops->sff_check_status(ap);
 648        dev_dbg(ap->dev, "%s ATA status register=0x%x\n", __func__, status);
 649
 650        tag = 0;
 651        num_processed = 0;
 652        while (tag_mask) {
 653                num_processed++;
 654                while (!(tag_mask & 0x00000001)) {
 655                        tag++;
 656                        tag_mask <<= 1;
 657                }
 658
 659                tag_mask &= (~0x00000001);
 660                qc = ata_qc_from_tag(ap, tag);
 661
 662                /* To be picked up by completion functions */
 663                qc->ap->link.active_tag = tag;
 664                hsdevp->cmd_issued[tag] = SATA_DWC_CMD_ISSUED_NOT;
 665
 666                /* Let libata/scsi layers handle error */
 667                if (status & ATA_ERR) {
 668                        dev_dbg(ap->dev, "%s ATA_ERR (0x%x)\n", __func__,
 669                                status);
 670                        sata_dwc_qc_complete(ap, qc, 1);
 671                        handled = 1;
 672                        goto DONE;
 673                }
 674
 675                /* Process completed command */
 676                dev_dbg(ap->dev, "%s NCQ command, protocol: %s\n", __func__,
 677                        get_prot_descript(qc->tf.protocol));
 678                if (ata_is_dma(qc->tf.protocol)) {
 679                        hsdevp->dma_interrupt_count++;
 680                        if (hsdevp->dma_pending[tag] == \
 681                                        SATA_DWC_DMA_PENDING_NONE)
 682                                dev_warn(ap->dev, "%s: DMA not pending?\n",
 683                                        __func__);
 684                        if ((hsdevp->dma_interrupt_count % 2) == 0)
 685                                sata_dwc_dma_xfer_complete(ap, 1);
 686                } else {
 687                        if (unlikely(sata_dwc_qc_complete(ap, qc, 1)))
 688                                goto STILLBUSY;
 689                }
 690                continue;
 691
 692STILLBUSY:
 693                ap->stats.idle_irq++;
 694                dev_warn(ap->dev, "STILL BUSY IRQ ata%d: irq trap\n",
 695                        ap->print_id);
 696        } /* while tag_mask */
 697
 698        /*
 699         * Check to see if any commands completed while we were processing our
 700         * initial set of completed commands (read status clears interrupts,
 701         * so we might miss a completed command interrupt if one came in while
 702         * we were processing --we read status as part of processing a completed
 703         * command).
 704         */
 705        sata_dwc_scr_read(&ap->link, SCR_ACTIVE, &sactive2);
 706        if (sactive2 != sactive) {
 707                dev_dbg(ap->dev,
 708                        "More completed - sactive=0x%x sactive2=0x%x\n",
 709                        sactive, sactive2);
 710        }
 711        handled = 1;
 712
 713DONE:
 714        spin_unlock_irqrestore(&host->lock, flags);
 715        return IRQ_RETVAL(handled);
 716}
 717
 718static void sata_dwc_clear_dmacr(struct sata_dwc_device_port *hsdevp, u8 tag)
 719{
 720        struct sata_dwc_device *hsdev = HSDEV_FROM_HSDEVP(hsdevp);
 721        u32 dmacr = sata_dwc_readl(&hsdev->sata_dwc_regs->dmacr);
 722
 723        if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_RX) {
 724                dmacr = SATA_DWC_DMACR_RX_CLEAR(dmacr);
 725                sata_dwc_writel(&hsdev->sata_dwc_regs->dmacr, dmacr);
 726        } else if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_TX) {
 727                dmacr = SATA_DWC_DMACR_TX_CLEAR(dmacr);
 728                sata_dwc_writel(&hsdev->sata_dwc_regs->dmacr, dmacr);
 729        } else {
 730                /*
 731                 * This should not happen, it indicates the driver is out of
 732                 * sync.  If it does happen, clear dmacr anyway.
 733                 */
 734                dev_err(hsdev->dev,
 735                        "%s DMA protocol RX and TX DMA not pending tag=0x%02x pending=%d dmacr: 0x%08x\n",
 736                        __func__, tag, hsdevp->dma_pending[tag], dmacr);
 737                sata_dwc_writel(&hsdev->sata_dwc_regs->dmacr,
 738                                SATA_DWC_DMACR_TXRXCH_CLEAR);
 739        }
 740}
 741
 742static void sata_dwc_dma_xfer_complete(struct ata_port *ap, u32 check_status)
 743{
 744        struct ata_queued_cmd *qc;
 745        struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
 746        struct sata_dwc_device *hsdev = HSDEV_FROM_AP(ap);
 747        u8 tag = 0;
 748
 749        tag = ap->link.active_tag;
 750        qc = ata_qc_from_tag(ap, tag);
 751        if (!qc) {
 752                dev_err(ap->dev, "failed to get qc");
 753                return;
 754        }
 755
 756#ifdef DEBUG_NCQ
 757        if (tag > 0) {
 758                dev_info(ap->dev,
 759                         "%s tag=%u cmd=0x%02x dma dir=%s proto=%s dmacr=0x%08x\n",
 760                         __func__, qc->hw_tag, qc->tf.command,
 761                         get_dma_dir_descript(qc->dma_dir),
 762                         get_prot_descript(qc->tf.protocol),
 763                         sata_dwc_readl(&hsdev->sata_dwc_regs->dmacr));
 764        }
 765#endif
 766
 767        if (ata_is_dma(qc->tf.protocol)) {
 768                if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_NONE) {
 769                        dev_err(ap->dev,
 770                                "%s DMA protocol RX and TX DMA not pending dmacr: 0x%08x\n",
 771                                __func__,
 772                                sata_dwc_readl(&hsdev->sata_dwc_regs->dmacr));
 773                }
 774
 775                hsdevp->dma_pending[tag] = SATA_DWC_DMA_PENDING_NONE;
 776                sata_dwc_qc_complete(ap, qc, check_status);
 777                ap->link.active_tag = ATA_TAG_POISON;
 778        } else {
 779                sata_dwc_qc_complete(ap, qc, check_status);
 780        }
 781}
 782
 783static int sata_dwc_qc_complete(struct ata_port *ap, struct ata_queued_cmd *qc,
 784                                u32 check_status)
 785{
 786        u8 status = 0;
 787        u32 mask = 0x0;
 788        u8 tag = qc->hw_tag;
 789        struct sata_dwc_device *hsdev = HSDEV_FROM_AP(ap);
 790        struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
 791        hsdev->sactive_queued = 0;
 792        dev_dbg(ap->dev, "%s checkstatus? %x\n", __func__, check_status);
 793
 794        if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_TX)
 795                dev_err(ap->dev, "TX DMA PENDING\n");
 796        else if (hsdevp->dma_pending[tag] == SATA_DWC_DMA_PENDING_RX)
 797                dev_err(ap->dev, "RX DMA PENDING\n");
 798        dev_dbg(ap->dev,
 799                "QC complete cmd=0x%02x status=0x%02x ata%u: protocol=%d\n",
 800                qc->tf.command, status, ap->print_id, qc->tf.protocol);
 801
 802        /* clear active bit */
 803        mask = (~(qcmd_tag_to_mask(tag)));
 804        hsdev->sactive_queued = hsdev->sactive_queued & mask;
 805        hsdev->sactive_issued = hsdev->sactive_issued & mask;
 806        ata_qc_complete(qc);
 807        return 0;
 808}
 809
 810static void sata_dwc_enable_interrupts(struct sata_dwc_device *hsdev)
 811{
 812        /* Enable selective interrupts by setting the interrupt maskregister*/
 813        sata_dwc_writel(&hsdev->sata_dwc_regs->intmr,
 814                        SATA_DWC_INTMR_ERRM |
 815                        SATA_DWC_INTMR_NEWFPM |
 816                        SATA_DWC_INTMR_PMABRTM |
 817                        SATA_DWC_INTMR_DMATM);
 818        /*
 819         * Unmask the error bits that should trigger an error interrupt by
 820         * setting the error mask register.
 821         */
 822        sata_dwc_writel(&hsdev->sata_dwc_regs->errmr, SATA_DWC_SERROR_ERR_BITS);
 823
 824        dev_dbg(hsdev->dev, "%s: INTMR = 0x%08x, ERRMR = 0x%08x\n",
 825                 __func__, sata_dwc_readl(&hsdev->sata_dwc_regs->intmr),
 826                sata_dwc_readl(&hsdev->sata_dwc_regs->errmr));
 827}
 828
 829static void sata_dwc_setup_port(struct ata_ioports *port, void __iomem *base)
 830{
 831        port->cmd_addr          = base + 0x00;
 832        port->data_addr         = base + 0x00;
 833
 834        port->error_addr        = base + 0x04;
 835        port->feature_addr      = base + 0x04;
 836
 837        port->nsect_addr        = base + 0x08;
 838
 839        port->lbal_addr         = base + 0x0c;
 840        port->lbam_addr         = base + 0x10;
 841        port->lbah_addr         = base + 0x14;
 842
 843        port->device_addr       = base + 0x18;
 844        port->command_addr      = base + 0x1c;
 845        port->status_addr       = base + 0x1c;
 846
 847        port->altstatus_addr    = base + 0x20;
 848        port->ctl_addr          = base + 0x20;
 849}
 850
 851static int sata_dwc_dma_get_channel(struct sata_dwc_device_port *hsdevp)
 852{
 853        struct sata_dwc_device *hsdev = hsdevp->hsdev;
 854        struct device *dev = hsdev->dev;
 855
 856#ifdef CONFIG_SATA_DWC_OLD_DMA
 857        if (!of_find_property(dev->of_node, "dmas", NULL))
 858                return sata_dwc_dma_get_channel_old(hsdevp);
 859#endif
 860
 861        hsdevp->chan = dma_request_chan(dev, "sata-dma");
 862        if (IS_ERR(hsdevp->chan)) {
 863                dev_err(dev, "failed to allocate dma channel: %ld\n",
 864                        PTR_ERR(hsdevp->chan));
 865                return PTR_ERR(hsdevp->chan);
 866        }
 867
 868        return 0;
 869}
 870
 871/*
 872 * Function : sata_dwc_port_start
 873 * arguments : struct ata_ioports *port
 874 * Return value : returns 0 if success, error code otherwise
 875 * This function allocates the scatter gather LLI table for AHB DMA
 876 */
 877static int sata_dwc_port_start(struct ata_port *ap)
 878{
 879        int err = 0;
 880        struct sata_dwc_device *hsdev;
 881        struct sata_dwc_device_port *hsdevp = NULL;
 882        struct device *pdev;
 883        int i;
 884
 885        hsdev = HSDEV_FROM_AP(ap);
 886
 887        dev_dbg(ap->dev, "%s: port_no=%d\n", __func__, ap->port_no);
 888
 889        hsdev->host = ap->host;
 890        pdev = ap->host->dev;
 891        if (!pdev) {
 892                dev_err(ap->dev, "%s: no ap->host->dev\n", __func__);
 893                err = -ENODEV;
 894                goto CLEANUP;
 895        }
 896
 897        /* Allocate Port Struct */
 898        hsdevp = kzalloc(sizeof(*hsdevp), GFP_KERNEL);
 899        if (!hsdevp) {
 900                err = -ENOMEM;
 901                goto CLEANUP;
 902        }
 903        hsdevp->hsdev = hsdev;
 904
 905        err = sata_dwc_dma_get_channel(hsdevp);
 906        if (err)
 907                goto CLEANUP_ALLOC;
 908
 909        err = phy_power_on(hsdev->phy);
 910        if (err)
 911                goto CLEANUP_ALLOC;
 912
 913        for (i = 0; i < SATA_DWC_QCMD_MAX; i++)
 914                hsdevp->cmd_issued[i] = SATA_DWC_CMD_ISSUED_NOT;
 915
 916        ap->bmdma_prd = NULL;   /* set these so libata doesn't use them */
 917        ap->bmdma_prd_dma = 0;
 918
 919        if (ap->port_no == 0)  {
 920                dev_dbg(ap->dev, "%s: clearing TXCHEN, RXCHEN in DMAC\n",
 921                        __func__);
 922                sata_dwc_writel(&hsdev->sata_dwc_regs->dmacr,
 923                                SATA_DWC_DMACR_TXRXCH_CLEAR);
 924
 925                dev_dbg(ap->dev, "%s: setting burst size in DBTSR\n",
 926                         __func__);
 927                sata_dwc_writel(&hsdev->sata_dwc_regs->dbtsr,
 928                                (SATA_DWC_DBTSR_MWR(AHB_DMA_BRST_DFLT) |
 929                                 SATA_DWC_DBTSR_MRD(AHB_DMA_BRST_DFLT)));
 930        }
 931
 932        /* Clear any error bits before libata starts issuing commands */
 933        clear_serror(ap);
 934        ap->private_data = hsdevp;
 935        dev_dbg(ap->dev, "%s: done\n", __func__);
 936        return 0;
 937
 938CLEANUP_ALLOC:
 939        kfree(hsdevp);
 940CLEANUP:
 941        dev_dbg(ap->dev, "%s: fail. ap->id = %d\n", __func__, ap->print_id);
 942        return err;
 943}
 944
 945static void sata_dwc_port_stop(struct ata_port *ap)
 946{
 947        struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
 948        struct sata_dwc_device *hsdev = HSDEV_FROM_AP(ap);
 949
 950        dev_dbg(ap->dev, "%s: ap->id = %d\n", __func__, ap->print_id);
 951
 952        dmaengine_terminate_sync(hsdevp->chan);
 953        dma_release_channel(hsdevp->chan);
 954        phy_power_off(hsdev->phy);
 955
 956        kfree(hsdevp);
 957        ap->private_data = NULL;
 958}
 959
 960/*
 961 * Function : sata_dwc_exec_command_by_tag
 962 * arguments : ata_port *ap, ata_taskfile *tf, u8 tag, u32 cmd_issued
 963 * Return value : None
 964 * This function keeps track of individual command tag ids and calls
 965 * ata_exec_command in libata
 966 */
 967static void sata_dwc_exec_command_by_tag(struct ata_port *ap,
 968                                         struct ata_taskfile *tf,
 969                                         u8 tag, u32 cmd_issued)
 970{
 971        struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
 972
 973        dev_dbg(ap->dev, "%s cmd(0x%02x): %s tag=%d\n", __func__, tf->command,
 974                ata_get_cmd_descript(tf->command), tag);
 975
 976        hsdevp->cmd_issued[tag] = cmd_issued;
 977
 978        /*
 979         * Clear SError before executing a new command.
 980         * sata_dwc_scr_write and read can not be used here. Clearing the PM
 981         * managed SError register for the disk needs to be done before the
 982         * task file is loaded.
 983         */
 984        clear_serror(ap);
 985        ata_sff_exec_command(ap, tf);
 986}
 987
 988static void sata_dwc_bmdma_setup_by_tag(struct ata_queued_cmd *qc, u8 tag)
 989{
 990        sata_dwc_exec_command_by_tag(qc->ap, &qc->tf, tag,
 991                                     SATA_DWC_CMD_ISSUED_PEND);
 992}
 993
 994static void sata_dwc_bmdma_setup(struct ata_queued_cmd *qc)
 995{
 996        u8 tag = qc->hw_tag;
 997
 998        if (ata_is_ncq(qc->tf.protocol)) {
 999                dev_dbg(qc->ap->dev, "%s: ap->link.sactive=0x%08x tag=%d\n",
1000                        __func__, qc->ap->link.sactive, tag);
1001        } else {
1002                tag = 0;
1003        }
1004        sata_dwc_bmdma_setup_by_tag(qc, tag);
1005}
1006
1007static void sata_dwc_bmdma_start_by_tag(struct ata_queued_cmd *qc, u8 tag)
1008{
1009        int start_dma;
1010        u32 reg;
1011        struct sata_dwc_device *hsdev = HSDEV_FROM_QC(qc);
1012        struct ata_port *ap = qc->ap;
1013        struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
1014        struct dma_async_tx_descriptor *desc = hsdevp->desc[tag];
1015        int dir = qc->dma_dir;
1016
1017        if (hsdevp->cmd_issued[tag] != SATA_DWC_CMD_ISSUED_NOT) {
1018                start_dma = 1;
1019                if (dir == DMA_TO_DEVICE)
1020                        hsdevp->dma_pending[tag] = SATA_DWC_DMA_PENDING_TX;
1021                else
1022                        hsdevp->dma_pending[tag] = SATA_DWC_DMA_PENDING_RX;
1023        } else {
1024                dev_err(ap->dev,
1025                        "%s: Command not pending cmd_issued=%d (tag=%d) DMA NOT started\n",
1026                        __func__, hsdevp->cmd_issued[tag], tag);
1027                start_dma = 0;
1028        }
1029
1030        dev_dbg(ap->dev,
1031                "%s qc=%p tag: %x cmd: 0x%02x dma_dir: %s start_dma? %x\n",
1032                __func__, qc, tag, qc->tf.command,
1033                get_dma_dir_descript(qc->dma_dir), start_dma);
1034        sata_dwc_tf_dump(ap, &qc->tf);
1035
1036        if (start_dma) {
1037                sata_dwc_scr_read(&ap->link, SCR_ERROR, &reg);
1038                if (reg & SATA_DWC_SERROR_ERR_BITS) {
1039                        dev_err(ap->dev, "%s: ****** SError=0x%08x ******\n",
1040                                __func__, reg);
1041                }
1042
1043                if (dir == DMA_TO_DEVICE)
1044                        sata_dwc_writel(&hsdev->sata_dwc_regs->dmacr,
1045                                        SATA_DWC_DMACR_TXCHEN);
1046                else
1047                        sata_dwc_writel(&hsdev->sata_dwc_regs->dmacr,
1048                                        SATA_DWC_DMACR_RXCHEN);
1049
1050                /* Enable AHB DMA transfer on the specified channel */
1051                dmaengine_submit(desc);
1052                dma_async_issue_pending(hsdevp->chan);
1053        }
1054}
1055
1056static void sata_dwc_bmdma_start(struct ata_queued_cmd *qc)
1057{
1058        u8 tag = qc->hw_tag;
1059
1060        if (ata_is_ncq(qc->tf.protocol)) {
1061                dev_dbg(qc->ap->dev, "%s: ap->link.sactive=0x%08x tag=%d\n",
1062                        __func__, qc->ap->link.sactive, tag);
1063        } else {
1064                tag = 0;
1065        }
1066        dev_dbg(qc->ap->dev, "%s\n", __func__);
1067        sata_dwc_bmdma_start_by_tag(qc, tag);
1068}
1069
1070static unsigned int sata_dwc_qc_issue(struct ata_queued_cmd *qc)
1071{
1072        u32 sactive;
1073        u8 tag = qc->hw_tag;
1074        struct ata_port *ap = qc->ap;
1075        struct sata_dwc_device_port *hsdevp = HSDEVP_FROM_AP(ap);
1076
1077#ifdef DEBUG_NCQ
1078        if (qc->hw_tag > 0 || ap->link.sactive > 1)
1079                dev_info(ap->dev,
1080                         "%s ap id=%d cmd(0x%02x)=%s qc tag=%d prot=%s ap active_tag=0x%08x ap sactive=0x%08x\n",
1081                         __func__, ap->print_id, qc->tf.command,
1082                         ata_get_cmd_descript(qc->tf.command),
1083                         qc->hw_tag, get_prot_descript(qc->tf.protocol),
1084                         ap->link.active_tag, ap->link.sactive);
1085#endif
1086
1087        if (!ata_is_ncq(qc->tf.protocol))
1088                tag = 0;
1089
1090        if (ata_is_dma(qc->tf.protocol)) {
1091                hsdevp->desc[tag] = dma_dwc_xfer_setup(qc);
1092                if (!hsdevp->desc[tag])
1093                        return AC_ERR_SYSTEM;
1094        } else {
1095                hsdevp->desc[tag] = NULL;
1096        }
1097
1098        if (ata_is_ncq(qc->tf.protocol)) {
1099                sata_dwc_scr_read(&ap->link, SCR_ACTIVE, &sactive);
1100                sactive |= (0x00000001 << tag);
1101                sata_dwc_scr_write(&ap->link, SCR_ACTIVE, sactive);
1102
1103                dev_dbg(qc->ap->dev,
1104                        "%s: tag=%d ap->link.sactive = 0x%08x sactive=0x%08x\n",
1105                        __func__, tag, qc->ap->link.sactive, sactive);
1106
1107                ap->ops->sff_tf_load(ap, &qc->tf);
1108                sata_dwc_exec_command_by_tag(ap, &qc->tf, tag,
1109                                             SATA_DWC_CMD_ISSUED_PEND);
1110        } else {
1111                return ata_bmdma_qc_issue(qc);
1112        }
1113        return 0;
1114}
1115
1116static void sata_dwc_error_handler(struct ata_port *ap)
1117{
1118        ata_sff_error_handler(ap);
1119}
1120
1121static int sata_dwc_hardreset(struct ata_link *link, unsigned int *class,
1122                              unsigned long deadline)
1123{
1124        struct sata_dwc_device *hsdev = HSDEV_FROM_AP(link->ap);
1125        int ret;
1126
1127        ret = sata_sff_hardreset(link, class, deadline);
1128
1129        sata_dwc_enable_interrupts(hsdev);
1130
1131        /* Reconfigure the DMA control register */
1132        sata_dwc_writel(&hsdev->sata_dwc_regs->dmacr,
1133                        SATA_DWC_DMACR_TXRXCH_CLEAR);
1134
1135        /* Reconfigure the DMA Burst Transaction Size register */
1136        sata_dwc_writel(&hsdev->sata_dwc_regs->dbtsr,
1137                        SATA_DWC_DBTSR_MWR(AHB_DMA_BRST_DFLT) |
1138                        SATA_DWC_DBTSR_MRD(AHB_DMA_BRST_DFLT));
1139
1140        return ret;
1141}
1142
1143static void sata_dwc_dev_select(struct ata_port *ap, unsigned int device)
1144{
1145        /* SATA DWC is master only */
1146}
1147
1148/*
1149 * scsi mid-layer and libata interface structures
1150 */
1151static struct scsi_host_template sata_dwc_sht = {
1152        ATA_NCQ_SHT(DRV_NAME),
1153        /*
1154         * test-only: Currently this driver doesn't handle NCQ
1155         * correctly. We enable NCQ but set the queue depth to a
1156         * max of 1. This will get fixed in in a future release.
1157         */
1158        .sg_tablesize           = LIBATA_MAX_PRD,
1159        /* .can_queue           = ATA_MAX_QUEUE, */
1160        /*
1161         * Make sure a LLI block is not created that will span 8K max FIS
1162         * boundary. If the block spans such a FIS boundary, there is a chance
1163         * that a DMA burst will cross that boundary -- this results in an
1164         * error in the host controller.
1165         */
1166        .dma_boundary           = 0x1fff /* ATA_DMA_BOUNDARY */,
1167};
1168
1169static struct ata_port_operations sata_dwc_ops = {
1170        .inherits               = &ata_sff_port_ops,
1171
1172        .error_handler          = sata_dwc_error_handler,
1173        .hardreset              = sata_dwc_hardreset,
1174
1175        .qc_issue               = sata_dwc_qc_issue,
1176
1177        .scr_read               = sata_dwc_scr_read,
1178        .scr_write              = sata_dwc_scr_write,
1179
1180        .port_start             = sata_dwc_port_start,
1181        .port_stop              = sata_dwc_port_stop,
1182
1183        .sff_dev_select         = sata_dwc_dev_select,
1184
1185        .bmdma_setup            = sata_dwc_bmdma_setup,
1186        .bmdma_start            = sata_dwc_bmdma_start,
1187};
1188
1189static const struct ata_port_info sata_dwc_port_info[] = {
1190        {
1191                .flags          = ATA_FLAG_SATA | ATA_FLAG_NCQ,
1192                .pio_mask       = ATA_PIO4,
1193                .udma_mask      = ATA_UDMA6,
1194                .port_ops       = &sata_dwc_ops,
1195        },
1196};
1197
1198static int sata_dwc_probe(struct platform_device *ofdev)
1199{
1200        struct sata_dwc_device *hsdev;
1201        u32 idr, versionr;
1202        char *ver = (char *)&versionr;
1203        void __iomem *base;
1204        int err = 0;
1205        int irq;
1206        struct ata_host *host;
1207        struct ata_port_info pi = sata_dwc_port_info[0];
1208        const struct ata_port_info *ppi[] = { &pi, NULL };
1209        struct device_node *np = ofdev->dev.of_node;
1210        struct resource *res;
1211
1212        /* Allocate DWC SATA device */
1213        host = ata_host_alloc_pinfo(&ofdev->dev, ppi, SATA_DWC_MAX_PORTS);
1214        hsdev = devm_kzalloc(&ofdev->dev, sizeof(*hsdev), GFP_KERNEL);
1215        if (!host || !hsdev)
1216                return -ENOMEM;
1217
1218        host->private_data = hsdev;
1219
1220        /* Ioremap SATA registers */
1221        res = platform_get_resource(ofdev, IORESOURCE_MEM, 0);
1222        base = devm_ioremap_resource(&ofdev->dev, res);
1223        if (IS_ERR(base))
1224                return PTR_ERR(base);
1225        dev_dbg(&ofdev->dev, "ioremap done for SATA register address\n");
1226
1227        /* Synopsys DWC SATA specific Registers */
1228        hsdev->sata_dwc_regs = base + SATA_DWC_REG_OFFSET;
1229        hsdev->dmadr = res->start + SATA_DWC_REG_OFFSET + offsetof(struct sata_dwc_regs, dmadr);
1230
1231        /* Setup port */
1232        host->ports[0]->ioaddr.cmd_addr = base;
1233        host->ports[0]->ioaddr.scr_addr = base + SATA_DWC_SCR_OFFSET;
1234        sata_dwc_setup_port(&host->ports[0]->ioaddr, base);
1235
1236        /* Read the ID and Version Registers */
1237        idr = sata_dwc_readl(&hsdev->sata_dwc_regs->idr);
1238        versionr = sata_dwc_readl(&hsdev->sata_dwc_regs->versionr);
1239        dev_notice(&ofdev->dev, "id %d, controller version %c.%c%c\n",
1240                   idr, ver[0], ver[1], ver[2]);
1241
1242        /* Save dev for later use in dev_xxx() routines */
1243        hsdev->dev = &ofdev->dev;
1244
1245        /* Enable SATA Interrupts */
1246        sata_dwc_enable_interrupts(hsdev);
1247
1248        /* Get SATA interrupt number */
1249        irq = irq_of_parse_and_map(np, 0);
1250        if (irq == NO_IRQ) {
1251                dev_err(&ofdev->dev, "no SATA DMA irq\n");
1252                err = -ENODEV;
1253                goto error_out;
1254        }
1255
1256#ifdef CONFIG_SATA_DWC_OLD_DMA
1257        if (!of_find_property(np, "dmas", NULL)) {
1258                err = sata_dwc_dma_init_old(ofdev, hsdev);
1259                if (err)
1260                        goto error_out;
1261        }
1262#endif
1263
1264        hsdev->phy = devm_phy_optional_get(hsdev->dev, "sata-phy");
1265        if (IS_ERR(hsdev->phy)) {
1266                err = PTR_ERR(hsdev->phy);
1267                hsdev->phy = NULL;
1268                goto error_out;
1269        }
1270
1271        err = phy_init(hsdev->phy);
1272        if (err)
1273                goto error_out;
1274
1275        /*
1276         * Now, register with libATA core, this will also initiate the
1277         * device discovery process, invoking our port_start() handler &
1278         * error_handler() to execute a dummy Softreset EH session
1279         */
1280        err = ata_host_activate(host, irq, sata_dwc_isr, 0, &sata_dwc_sht);
1281        if (err)
1282                dev_err(&ofdev->dev, "failed to activate host");
1283
1284        return 0;
1285
1286error_out:
1287        phy_exit(hsdev->phy);
1288        return err;
1289}
1290
1291static int sata_dwc_remove(struct platform_device *ofdev)
1292{
1293        struct device *dev = &ofdev->dev;
1294        struct ata_host *host = dev_get_drvdata(dev);
1295        struct sata_dwc_device *hsdev = host->private_data;
1296
1297        ata_host_detach(host);
1298
1299        phy_exit(hsdev->phy);
1300
1301#ifdef CONFIG_SATA_DWC_OLD_DMA
1302        /* Free SATA DMA resources */
1303        sata_dwc_dma_exit_old(hsdev);
1304#endif
1305
1306        dev_dbg(&ofdev->dev, "done\n");
1307        return 0;
1308}
1309
1310static const struct of_device_id sata_dwc_match[] = {
1311        { .compatible = "amcc,sata-460ex", },
1312        {}
1313};
1314MODULE_DEVICE_TABLE(of, sata_dwc_match);
1315
1316static struct platform_driver sata_dwc_driver = {
1317        .driver = {
1318                .name = DRV_NAME,
1319                .of_match_table = sata_dwc_match,
1320        },
1321        .probe = sata_dwc_probe,
1322        .remove = sata_dwc_remove,
1323};
1324
1325module_platform_driver(sata_dwc_driver);
1326
1327MODULE_LICENSE("GPL");
1328MODULE_AUTHOR("Mark Miesfeld <mmiesfeld@amcc.com>");
1329MODULE_DESCRIPTION("DesignWare Cores SATA controller low level driver");
1330MODULE_VERSION(DRV_VERSION);
1331