// SPDX-License-Identifier: GPL-2.0-only
/*
 * Driver for Linear Technology LTC4215 I2C Hot Swap Controller
 *
 * Copyright (C) 2009 Ira W. Snyder <iws@ovro.caltech.edu>
 *
 * Datasheet:
 * http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1163,P17572,D12697
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/err.h>
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/jiffies.h>

/* Here are names of the chip's registers (a.k.a. commands) */
enum ltc4215_cmd {
        LTC4215_CONTROL                 = 0x00, /* rw */
        LTC4215_ALERT                   = 0x01, /* rw */
        LTC4215_STATUS                  = 0x02, /* ro */
        LTC4215_FAULT                   = 0x03, /* rw */
        LTC4215_SENSE                   = 0x04, /* rw */
        LTC4215_SOURCE                  = 0x05, /* rw */
        LTC4215_ADIN                    = 0x06, /* rw */
};

struct ltc4215_data {
        struct i2c_client *client;

        struct mutex update_lock;
        bool valid;
        unsigned long last_updated; /* in jiffies */

        /* Registers */
        u8 regs[7];
};

static struct ltc4215_data *ltc4215_update_device(struct device *dev)
{
        struct ltc4215_data *data = dev_get_drvdata(dev);
        struct i2c_client *client = data->client;
        s32 val;
        int i;

        mutex_lock(&data->update_lock);

        /* The chip's A/D updates 10 times per second */
        if (time_after(jiffies, data->last_updated + HZ / 10) || !data->valid) {

                dev_dbg(&client->dev, "Starting ltc4215 update\n");

                /* Read all registers */
                for (i = 0; i < ARRAY_SIZE(data->regs); i++) {
                        val = i2c_smbus_read_byte_data(client, i);
                        if (unlikely(val < 0))
                                data->regs[i] = 0;
                        else
                                data->regs[i] = val;
                }

                data->last_updated = jiffies;
                data->valid = 1;
        }

        mutex_unlock(&data->update_lock);

        return data;
}

/* Return the voltage from the given register in millivolts */
static int ltc4215_get_voltage(struct device *dev, u8 reg)
{
        struct ltc4215_data *data = ltc4215_update_device(dev);
        const u8 regval = data->regs[reg];
        u32 voltage = 0;

        switch (reg) {
        case LTC4215_SENSE:
                /* 151 uV per increment */
                voltage = regval * 151 / 1000;
                break;
        case LTC4215_SOURCE:
                /* 60.5 mV per increment */
                voltage = regval * 605 / 10;
                break;
        case LTC4215_ADIN:
                /*
                 * The ADIN input is divided by 12.5, and has 4.82 mV
                 * per increment, so we have the additional multiply
                 */
                voltage = regval * 482 * 125 / 1000;
                break;
        default:
                /* If we get here, the developer messed up */
                WARN_ON_ONCE(1);
                break;
        }

        return voltage;
}

/* Return the current from the sense resistor in mA */
static unsigned int ltc4215_get_current(struct device *dev)
{
        struct ltc4215_data *data = ltc4215_update_device(dev);

        /*
         * The strange looking conversions that follow are fixed-point
         * math, since we cannot do floating point in the kernel.
         *
         * Step 1: convert sense register to microVolts
         * Step 2: convert voltage to milliAmperes
         *
         * If you play around with the V=IR equation, you come up with
         * the following: X uV / Y mOhm == Z mA
         *
         * With the resistors that are fractions of a milliOhm, we multiply
         * the voltage and resistance by 10, to shift the decimal point.
         * Now we can use the normal division operator again.
         */

        /* Calculate voltage in microVolts (151 uV per increment) */
        const unsigned int voltage = data->regs[LTC4215_SENSE] * 151;

        /* Calculate current in milliAmperes (4 milliOhm sense resistor) */
        const unsigned int curr = voltage / 4;

        return curr;
}

static ssize_t ltc4215_voltage_show(struct device *dev,
                                    struct device_attribute *da, char *buf)
{
        struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
        const int voltage = ltc4215_get_voltage(dev, attr->index);

        return snprintf(buf, PAGE_SIZE, "%d\n", voltage);
}

static ssize_t ltc4215_current_show(struct device *dev,
                                    struct device_attribute *da, char *buf)
{
        const unsigned int curr = ltc4215_get_current(dev);

        return snprintf(buf, PAGE_SIZE, "%u\n", curr);
}

static ssize_t ltc4215_power_show(struct device *dev,
                                  struct device_attribute *da, char *buf)
{
        const unsigned int curr = ltc4215_get_current(dev);
        const int output_voltage = ltc4215_get_voltage(dev, LTC4215_ADIN);

        /* current in mA * voltage in mV == power in uW */
        const unsigned int power = abs(output_voltage * curr);

        return snprintf(buf, PAGE_SIZE, "%u\n", power);
}

static ssize_t ltc4215_alarm_show(struct device *dev,
                                  struct device_attribute *da, char *buf)
{
        struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
        struct ltc4215_data *data = ltc4215_update_device(dev);
        const u8 reg = data->regs[LTC4215_STATUS];
        const u32 mask = attr->index;

        return snprintf(buf, PAGE_SIZE, "%u\n", !!(reg & mask));
}

/*
 * These macros are used below in constructing device attribute objects
 * for use with sysfs_create_group() to make a sysfs device file
 * for each register.
 */

/* Construct a sensor_device_attribute structure for each register */

/* Current */
static SENSOR_DEVICE_ATTR_RO(curr1_input, ltc4215_current, 0);
static SENSOR_DEVICE_ATTR_RO(curr1_max_alarm, ltc4215_alarm, 1 << 2);

/* Power (virtual) */
static SENSOR_DEVICE_ATTR_RO(power1_input, ltc4215_power, 0);

/* Input Voltage */
static SENSOR_DEVICE_ATTR_RO(in1_input, ltc4215_voltage, LTC4215_ADIN);
static SENSOR_DEVICE_ATTR_RO(in1_max_alarm, ltc4215_alarm, 1 << 0);
static SENSOR_DEVICE_ATTR_RO(in1_min_alarm, ltc4215_alarm, 1 << 1);

/* Output Voltage */
static SENSOR_DEVICE_ATTR_RO(in2_input, ltc4215_voltage, LTC4215_SOURCE);
static SENSOR_DEVICE_ATTR_RO(in2_min_alarm, ltc4215_alarm, 1 << 3);

/*
 * Finally, construct an array of pointers to members of the above objects,
 * as required for sysfs_create_group()
 */
static struct attribute *ltc4215_attrs[] = {
        &sensor_dev_attr_curr1_input.dev_attr.attr,
        &sensor_dev_attr_curr1_max_alarm.dev_attr.attr,

        &sensor_dev_attr_power1_input.dev_attr.attr,

        &sensor_dev_attr_in1_input.dev_attr.attr,
        &sensor_dev_attr_in1_max_alarm.dev_attr.attr,
        &sensor_dev_attr_in1_min_alarm.dev_attr.attr,

        &sensor_dev_attr_in2_input.dev_attr.attr,
        &sensor_dev_attr_in2_min_alarm.dev_attr.attr,

        NULL,
};
ATTRIBUTE_GROUPS(ltc4215);

static int ltc4215_probe(struct i2c_client *client,
                         const struct i2c_device_id *id)
{
        struct i2c_adapter *adapter = client->adapter;
        struct device *dev = &client->dev;
        struct ltc4215_data *data;
        struct device *hwmon_dev;

        if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
                return -ENODEV;

        data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
        if (!data)
                return -ENOMEM;

        data->client = client;
        mutex_init(&data->update_lock);

        /* Initialize the LTC4215 chip */
        i2c_smbus_write_byte_data(client, LTC4215_FAULT, 0x00);

        hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
                                                           data,
                                                           ltc4215_groups);
        return PTR_ERR_OR_ZERO(hwmon_dev);
}

static const struct i2c_device_id ltc4215_id[] = {
        { "ltc4215", 0 },
        { }
};
MODULE_DEVICE_TABLE(i2c, ltc4215_id);

/* This is the driver that will be inserted */
static struct i2c_driver ltc4215_driver = {
        .driver = {
                .name   = "ltc4215",
        },
        .probe          = ltc4215_probe,
        .id_table       = ltc4215_id,
};

module_i2c_driver(ltc4215_driver);

MODULE_AUTHOR("Ira W. Snyder <iws@ovro.caltech.edu>");
MODULE_DESCRIPTION("LTC4215 driver");
MODULE_LICENSE("GPL");