// SPDX-License-Identifier: GPL-2.0
/*
 * sht15.c - support for the SHT15 Temperature and Humidity Sensor
 *
 * Portions Copyright (c) 2010-2012 Savoir-faire Linux Inc.
 *          Jerome Oufella <jerome.oufella@savoirfairelinux.com>
 *          Vivien Didelot <vivien.didelot@savoirfairelinux.com>
 *
 * Copyright (c) 2009 Jonathan Cameron
 *
 * Copyright (c) 2007 Wouter Horre
 *
 * For further information, see the Documentation/hwmon/sht15.rst file.
 */

#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/hwmon.h>
#include <linux/hwmon-sysfs.h>
#include <linux/mutex.h>
#include <linux/platform_device.h>
#include <linux/sched.h>
#include <linux/delay.h>
#include <linux/jiffies.h>
#include <linux/err.h>
#include <linux/regulator/consumer.h>
#include <linux/slab.h>
#include <linux/atomic.h>
#include <linux/bitrev.h>
#include <linux/gpio/consumer.h>
#include <linux/of.h>

/* Commands */
#define SHT15_MEASURE_TEMP              0x03
#define SHT15_MEASURE_RH                0x05
#define SHT15_WRITE_STATUS              0x06
#define SHT15_READ_STATUS               0x07
#define SHT15_SOFT_RESET                0x1E

/* Min timings */
#define SHT15_TSCKL                     100     /* (nsecs) clock low */
#define SHT15_TSCKH                     100     /* (nsecs) clock high */
#define SHT15_TSU                       150     /* (nsecs) data setup time */
#define SHT15_TSRST                     11      /* (msecs) soft reset time */

/* Status Register Bits */
#define SHT15_STATUS_LOW_RESOLUTION     0x01
#define SHT15_STATUS_NO_OTP_RELOAD      0x02
#define SHT15_STATUS_HEATER             0x04
#define SHT15_STATUS_LOW_BATTERY        0x40

/* List of supported chips */
enum sht15_chips { sht10, sht11, sht15, sht71, sht75 };

/* Actions the driver may be doing */
enum sht15_state {
        SHT15_READING_NOTHING,
        SHT15_READING_TEMP,
        SHT15_READING_HUMID
};

/**
 * struct sht15_temppair - elements of voltage dependent temp calc
 * @vdd:        supply voltage in microvolts
 * @d1:         see data sheet
 */
struct sht15_temppair {
        int vdd; /* microvolts */
        int d1;
};

/* Table 9 from datasheet - relates temperature calculation to supply voltage */
static const struct sht15_temppair temppoints[] = {
        { 2500000, -39400 },
        { 3000000, -39600 },
        { 3500000, -39700 },
        { 4000000, -39800 },
        { 5000000, -40100 },
};

/* Table from CRC datasheet, section 2.4 */
static const u8 sht15_crc8_table[] = {
        0,      49,     98,     83,     196,    245,    166,    151,
        185,    136,    219,    234,    125,    76,     31,     46,
        67,     114,    33,     16,     135,    182,    229,    212,
        250,    203,    152,    169,    62,     15,     92,     109,
        134,    183,    228,    213,    66,     115,    32,     17,
        63,     14,     93,     108,    251,    202,    153,    168,
        197,    244,    167,    150,    1,      48,     99,     82,
        124,    77,     30,     47,     184,    137,    218,    235,
        61,     12,     95,     110,    249,    200,    155,    170,
        132,    181,    230,    215,    64,     113,    34,     19,
        126,    79,     28,     45,     186,    139,    216,    233,
        199,    246,    165,    148,    3,      50,     97,     80,
        187,    138,    217,    232,    127,    78,     29,     44,
        2,      51,     96,     81,     198,    247,    164,    149,
        248,    201,    154,    171,    60,     13,     94,     111,
        65,     112,    35,     18,     133,    180,    231,    214,
        122,    75,     24,     41,     190,    143,    220,    237,
        195,    242,    161,    144,    7,      54,     101,    84,
        57,     8,      91,     106,    253,    204,    159,    174,
        128,    177,    226,    211,    68,     117,    38,     23,
        252,    205,    158,    175,    56,     9,      90,     107,
        69,     116,    39,     22,     129,    176,    227,    210,
        191,    142,    221,    236,    123,    74,     25,     40,
        6,      55,     100,    85,     194,    243,    160,    145,
        71,     118,    37,     20,     131,    178,    225,    208,
        254,    207,    156,    173,    58,     11,     88,     105,
        4,      53,     102,    87,     192,    241,    162,    147,
        189,    140,    223,    238,    121,    72,     27,     42,
        193,    240,    163,    146,    5,      52,     103,    86,
        120,    73,     26,     43,     188,    141,    222,    239,
        130,    179,    224,    209,    70,     119,    36,     21,
        59,     10,     89,     104,    255,    206,    157,    172
};

/**
 * struct sht15_data - device instance specific data
 * @sck:                clock GPIO line
 * @data:               data GPIO line
 * @read_work:          bh of interrupt handler.
 * @wait_queue:         wait queue for getting values from device.
 * @val_temp:           last temperature value read from device.
 * @val_humid:          last humidity value read from device.
 * @val_status:         last status register value read from device.
 * @checksum_ok:        last value read from the device passed CRC validation.
 * @checksumming:       flag used to enable the data validation with CRC.
 * @state:              state identifying the action the driver is doing.
 * @measurements_valid: are the current stored measures valid (start condition).
 * @status_valid:       is the current stored status valid (start condition).
 * @last_measurement:   time of last measure.
 * @last_status:        time of last status reading.
 * @read_lock:          mutex to ensure only one read in progress at a time.
 * @dev:                associate device structure.
 * @hwmon_dev:          device associated with hwmon subsystem.
 * @reg:                associated regulator (if specified).
 * @nb:                 notifier block to handle notifications of voltage
 *                      changes.
 * @supply_uv:          local copy of supply voltage used to allow use of
 *                      regulator consumer if available.
 * @supply_uv_valid:    indicates that an updated value has not yet been
 *                      obtained from the regulator and so any calculations
 *                      based upon it will be invalid.
 * @update_supply_work: work struct that is used to update the supply_uv.
 * @interrupt_handled:  flag used to indicate a handler has been scheduled.
 */
struct sht15_data {
        struct gpio_desc                *sck;
        struct gpio_desc                *data;
        struct work_struct              read_work;
        wait_queue_head_t               wait_queue;
        uint16_t                        val_temp;
        uint16_t                        val_humid;
        u8                              val_status;
        bool                            checksum_ok;
        bool                            checksumming;
        enum sht15_state                state;
        bool                            measurements_valid;
        bool                            status_valid;
        unsigned long                   last_measurement;
        unsigned long                   last_status;
        struct mutex                    read_lock;
        struct device                   *dev;
        struct device                   *hwmon_dev;
        struct regulator                *reg;
        struct notifier_block           nb;
        int                             supply_uv;
        bool                            supply_uv_valid;
        struct work_struct              update_supply_work;
        atomic_t                        interrupt_handled;
};

/**
 * sht15_crc8() - compute crc8
 * @data:       sht15 specific data.
 * @value:      sht15 retrieved data.
 * @len:        Length of retrieved data
 *
 * This implements section 2 of the CRC datasheet.
 */
static u8 sht15_crc8(struct sht15_data *data,
                const u8 *value,
                int len)
{
        u8 crc = bitrev8(data->val_status & 0x0F);

        while (len--) {
                crc = sht15_crc8_table[*value ^ crc];
                value++;
        }

        return crc;
}

/**
 * sht15_connection_reset() - reset the comms interface
 * @data:       sht15 specific data
 *
 * This implements section 3.4 of the data sheet
 */
static int sht15_connection_reset(struct sht15_data *data)
{
        int i, err;

        err = gpiod_direction_output(data->data, 1);
        if (err)
                return err;
        ndelay(SHT15_TSCKL);
        gpiod_set_value(data->sck, 0);
        ndelay(SHT15_TSCKL);
        for (i = 0; i < 9; ++i) {
                gpiod_set_value(data->sck, 1);
                ndelay(SHT15_TSCKH);
                gpiod_set_value(data->sck, 0);
                ndelay(SHT15_TSCKL);
        }
        return 0;
}

/**
 * sht15_send_bit() - send an individual bit to the device
 * @data:       device state data
 * @val:        value of bit to be sent
 */
static inline void sht15_send_bit(struct sht15_data *data, int val)
{
        gpiod_set_value(data->data, val);
        ndelay(SHT15_TSU);
        gpiod_set_value(data->sck, 1);
        ndelay(SHT15_TSCKH);
        gpiod_set_value(data->sck, 0);
        ndelay(SHT15_TSCKL); /* clock low time */
}

/**
 * sht15_transmission_start() - specific sequence for new transmission
 * @data:       device state data
 *
 * Timings for this are not documented on the data sheet, so very
 * conservative ones used in implementation. This implements
 * figure 12 on the data sheet.
 */
static int sht15_transmission_start(struct sht15_data *data)
{
        int err;

        /* ensure data is high and output */
        err = gpiod_direction_output(data->data, 1);
        if (err)
                return err;
        ndelay(SHT15_TSU);
        gpiod_set_value(data->sck, 0);
        ndelay(SHT15_TSCKL);
        gpiod_set_value(data->sck, 1);
        ndelay(SHT15_TSCKH);
        gpiod_set_value(data->data, 0);
        ndelay(SHT15_TSU);
        gpiod_set_value(data->sck, 0);
        ndelay(SHT15_TSCKL);
        gpiod_set_value(data->sck, 1);
        ndelay(SHT15_TSCKH);
        gpiod_set_value(data->data, 1);
        ndelay(SHT15_TSU);
        gpiod_set_value(data->sck, 0);
        ndelay(SHT15_TSCKL);
        return 0;
}

/**
 * sht15_send_byte() - send a single byte to the device
 * @data:       device state
 * @byte:       value to be sent
 */
static void sht15_send_byte(struct sht15_data *data, u8 byte)
{
        int i;

        for (i = 0; i < 8; i++) {
                sht15_send_bit(data, !!(byte & 0x80));
                byte <<= 1;
        }
}

/**
 * sht15_wait_for_response() - checks for ack from device
 * @data:       device state
 */
static int sht15_wait_for_response(struct sht15_data *data)
{
        int err;

        err = gpiod_direction_input(data->data);
        if (err)
                return err;
        gpiod_set_value(data->sck, 1);
        ndelay(SHT15_TSCKH);
        if (gpiod_get_value(data->data)) {
                gpiod_set_value(data->sck, 0);
                dev_err(data->dev, "Command not acknowledged\n");
                err = sht15_connection_reset(data);
                if (err)
                        return err;
                return -EIO;
        }
        gpiod_set_value(data->sck, 0);
        ndelay(SHT15_TSCKL);
        return 0;
}

/**
 * sht15_send_cmd() - Sends a command to the device.
 * @data:       device state
 * @cmd:        command byte to be sent
 *
 * On entry, sck is output low, data is output pull high
 * and the interrupt disabled.
 */
static int sht15_send_cmd(struct sht15_data *data, u8 cmd)
{
        int err;

        err = sht15_transmission_start(data);
        if (err)
                return err;
        sht15_send_byte(data, cmd);
        return sht15_wait_for_response(data);
}

/**
 * sht15_soft_reset() - send a soft reset command
 * @data:       sht15 specific data.
 *
 * As described in section 3.2 of the datasheet.
 */
static int sht15_soft_reset(struct sht15_data *data)
{
        int ret;

        ret = sht15_send_cmd(data, SHT15_SOFT_RESET);
        if (ret)
                return ret;
        msleep(SHT15_TSRST);
        /* device resets default hardware status register value */
        data->val_status = 0;

        return ret;
}

/**
 * sht15_ack() - send a ack
 * @data:       sht15 specific data.
 *
 * Each byte of data is acknowledged by pulling the data line
 * low for one clock pulse.
 */
static int sht15_ack(struct sht15_data *data)
{
        int err;

        err = gpiod_direction_output(data->data, 0);
        if (err)
                return err;
        ndelay(SHT15_TSU);
        gpiod_set_value(data->sck, 1);
        ndelay(SHT15_TSU);
        gpiod_set_value(data->sck, 0);
        ndelay(SHT15_TSU);
        gpiod_set_value(data->data, 1);

        return gpiod_direction_input(data->data);
}

/**
 * sht15_end_transmission() - notify device of end of transmission
 * @data:       device state.
 *
 * This is basically a NAK (single clock pulse, data high).
 */
static int sht15_end_transmission(struct sht15_data *data)
{
        int err;

        err = gpiod_direction_output(data->data, 1);
        if (err)
                return err;
        ndelay(SHT15_TSU);
        gpiod_set_value(data->sck, 1);
        ndelay(SHT15_TSCKH);
        gpiod_set_value(data->sck, 0);
        ndelay(SHT15_TSCKL);
        return 0;
}

/**
 * sht15_read_byte() - Read a byte back from the device
 * @data:       device state.
 */
static u8 sht15_read_byte(struct sht15_data *data)
{
        int i;
        u8 byte = 0;

        for (i = 0; i < 8; ++i) {
                byte <<= 1;
                gpiod_set_value(data->sck, 1);
                ndelay(SHT15_TSCKH);
                byte |= !!gpiod_get_value(data->data);
                gpiod_set_value(data->sck, 0);
                ndelay(SHT15_TSCKL);
        }
        return byte;
}

/**
 * sht15_send_status() - write the status register byte
 * @data:       sht15 specific data.
 * @status:     the byte to set the status register with.
 *
 * As described in figure 14 and table 5 of the datasheet.
 */
static int sht15_send_status(struct sht15_data *data, u8 status)
{
        int err;

        err = sht15_send_cmd(data, SHT15_WRITE_STATUS);
        if (err)
                return err;
        err = gpiod_direction_output(data->data, 1);
        if (err)
                return err;
        ndelay(SHT15_TSU);
        sht15_send_byte(data, status);
        err = sht15_wait_for_response(data);
        if (err)
                return err;

        data->val_status = status;
        return 0;
}

/**
 * sht15_update_status() - get updated status register from device if too old
 * @data:       device instance specific data.
 *
 * As described in figure 15 and table 5 of the datasheet.
 */
static int sht15_update_status(struct sht15_data *data)
{
        int ret = 0;
        u8 status;
        u8 previous_config;
        u8 dev_checksum = 0;
        u8 checksum_vals[2];
        int timeout = HZ;

        mutex_lock(&data->read_lock);
        if (time_after(jiffies, data->last_status + timeout)
                        || !data->status_valid) {
                ret = sht15_send_cmd(data, SHT15_READ_STATUS);
                if (ret)
                        goto unlock;
                status = sht15_read_byte(data);

                if (data->checksumming) {
                        sht15_ack(data);
                        dev_checksum = bitrev8(sht15_read_byte(data));
                        checksum_vals[0] = SHT15_READ_STATUS;
                        checksum_vals[1] = status;
                        data->checksum_ok = (sht15_crc8(data, checksum_vals, 2)
                                        == dev_checksum);
                }

                ret = sht15_end_transmission(data);
                if (ret)
                        goto unlock;

                /*
                 * Perform checksum validation on the received data.
                 * Specification mentions that in case a checksum verification
                 * fails, a soft reset command must be sent to the device.
                 */
                if (data->checksumming && !data->checksum_ok) {
                        previous_config = data->val_status & 0x07;
                        ret = sht15_soft_reset(data);
                        if (ret)
                                goto unlock;
                        if (previous_config) {
                                ret = sht15_send_status(data, previous_config);
                                if (ret) {
                                        dev_err(data->dev,
                                                "CRC validation failed, unable "
                                                "to restore device settings\n");
                                        goto unlock;
                                }
                        }
                        ret = -EAGAIN;
                        goto unlock;
                }

                data->val_status = status;
                data->status_valid = true;
                data->last_status = jiffies;
        }

unlock:
        mutex_unlock(&data->read_lock);
        return ret;
}

/**
 * sht15_measurement() - get a new value from device
 * @data:               device instance specific data
 * @command:            command sent to request value
 * @timeout_msecs:      timeout after which comms are assumed
 *                      to have failed are reset.
 */
static int sht15_measurement(struct sht15_data *data,
                             int command,
                             int timeout_msecs)
{
        int ret;
        u8 previous_config;

        ret = sht15_send_cmd(data, command);
        if (ret)
                return ret;

        ret = gpiod_direction_input(data->data);
        if (ret)
                return ret;
        atomic_set(&data->interrupt_handled, 0);

        enable_irq(gpiod_to_irq(data->data));
        if (gpiod_get_value(data->data) == 0) {
                disable_irq_nosync(gpiod_to_irq(data->data));
                /* Only relevant if the interrupt hasn't occurred. */
                if (!atomic_read(&data->interrupt_handled))
                        schedule_work(&data->read_work);
        }
        ret = wait_event_timeout(data->wait_queue,
                                 (data->state == SHT15_READING_NOTHING),
                                 msecs_to_jiffies(timeout_msecs));
        if (data->state != SHT15_READING_NOTHING) { /* I/O error occurred */
                data->state = SHT15_READING_NOTHING;
                return -EIO;
        } else if (ret == 0) { /* timeout occurred */
                disable_irq_nosync(gpiod_to_irq(data->data));
                ret = sht15_connection_reset(data);
                if (ret)
                        return ret;
                return -ETIME;
        }

        /*
         *  Perform checksum validation on the received data.
         *  Specification mentions that in case a checksum verification fails,
         *  a soft reset command must be sent to the device.
         */
        if (data->checksumming && !data->checksum_ok) {
                previous_config = data->val_status & 0x07;
                ret = sht15_soft_reset(data);
                if (ret)
                        return ret;
                if (previous_config) {
                        ret = sht15_send_status(data, previous_config);
                        if (ret) {
                                dev_err(data->dev,
                                        "CRC validation failed, unable "
                                        "to restore device settings\n");
                                return ret;
                        }
                }
                return -EAGAIN;
        }

        return 0;
}

/**
 * sht15_update_measurements() - get updated measures from device if too old
 * @data:       device state
 */
static int sht15_update_measurements(struct sht15_data *data)
{
        int ret = 0;
        int timeout = HZ;

        mutex_lock(&data->read_lock);
        if (time_after(jiffies, data->last_measurement + timeout)
            || !data->measurements_valid) {
                data->state = SHT15_READING_HUMID;
                ret = sht15_measurement(data, SHT15_MEASURE_RH, 160);
                if (ret)
                        goto unlock;
                data->state = SHT15_READING_TEMP;
                ret = sht15_measurement(data, SHT15_MEASURE_TEMP, 400);
                if (ret)
                        goto unlock;
                data->measurements_valid = true;
                data->last_measurement = jiffies;
        }

unlock:
        mutex_unlock(&data->read_lock);
        return ret;
}

/**
 * sht15_calc_temp() - convert the raw reading to a temperature
 * @data:       device state
 *
 * As per section 4.3 of the data sheet.
 */
static inline int sht15_calc_temp(struct sht15_data *data)
{
        int d1 = temppoints[0].d1;
        int d2 = (data->val_status & SHT15_STATUS_LOW_RESOLUTION) ? 40 : 10;
        int i;

        for (i = ARRAY_SIZE(temppoints) - 1; i > 0; i--)
                /* Find pointer to interpolate */
                if (data->supply_uv > temppoints[i - 1].vdd) {
                        d1 = (data->supply_uv - temppoints[i - 1].vdd)
                                * (temppoints[i].d1 - temppoints[i - 1].d1)
                                / (temppoints[i].vdd - temppoints[i - 1].vdd)
                                + temppoints[i - 1].d1;
                        break;
                }

        return data->val_temp * d2 + d1;
}

/**
 * sht15_calc_humid() - using last temperature convert raw to humid
 * @data:       device state
 *
 * This is the temperature compensated version as per section 4.2 of
 * the data sheet.
 *
 * The sensor is assumed to be V3, which is compatible with V4.
 * Humidity conversion coefficients are shown in table 7 of the datasheet.
 */
static inline int sht15_calc_humid(struct sht15_data *data)
{
        int rh_linear; /* milli percent */
        int temp = sht15_calc_temp(data);
        int c2, c3;
        int t2;
        const int c1 = -4;

        if (data->val_status & SHT15_STATUS_LOW_RESOLUTION) {
                c2 = 648000; /* x 10 ^ -6 */
                c3 = -7200;  /* x 10 ^ -7 */
                t2 = 1280;
        } else {
                c2 = 40500;  /* x 10 ^ -6 */
                c3 = -28;    /* x 10 ^ -7 */
                t2 = 80;
        }

        rh_linear = c1 * 1000
                + c2 * data->val_humid / 1000
                + (data->val_humid * data->val_humid * c3) / 10000;
        return (temp - 25000) * (10000 + t2 * data->val_humid)
                / 1000000 + rh_linear;
}

/**
 * sht15_show_status() - show status information in sysfs
 * @dev:        device.
 * @attr:       device attribute.
 * @buf:        sysfs buffer where information is written to.
 *
 * Will be called on read access to temp1_fault, humidity1_fault
 * and heater_enable sysfs attributes.
 * Returns number of bytes written into buffer, negative errno on error.
 */
static ssize_t sht15_status_show(struct device *dev,
                                 struct device_attribute *attr, char *buf)
{
        int ret;
        struct sht15_data *data = dev_get_drvdata(dev);
        u8 bit = to_sensor_dev_attr(attr)->index;

        ret = sht15_update_status(data);

        return ret ? ret : sprintf(buf, "%d\n", !!(data->val_status & bit));
}

/**
 * sht15_store_heater() - change heater state via sysfs
 * @dev:        device.
 * @attr:       device attribute.
 * @buf:        sysfs buffer to read the new heater state from.
 * @count:      length of the data.
 *
 * Will be called on write access to heater_enable sysfs attribute.
 * Returns number of bytes actually decoded, negative errno on error.
 */
static ssize_t sht15_status_store(struct device *dev,
                                  struct device_attribute *attr,
                                  const char *buf, size_t count)
{
        int ret;
        struct sht15_data *data = dev_get_drvdata(dev);
        long value;
        u8 status;

        if (kstrtol(buf, 10, &value))
                return -EINVAL;

        mutex_lock(&data->read_lock);
        status = data->val_status & 0x07;
        if (!!value)
                status |= SHT15_STATUS_HEATER;
        else
                status &= ~SHT15_STATUS_HEATER;

        ret = sht15_send_status(data, status);
        mutex_unlock(&data->read_lock);

        return ret ? ret : count;
}

/**
 * sht15_show_temp() - show temperature measurement value in sysfs
 * @dev:        device.
 * @attr:       device attribute.
 * @buf:        sysfs buffer where measurement values are written to.
 *
 * Will be called on read access to temp1_input sysfs attribute.
 * Returns number of bytes written into buffer, negative errno on error.
 */
static ssize_t sht15_temp_show(struct device *dev,
                               struct device_attribute *attr, char *buf)
{
        int ret;
        struct sht15_data *data = dev_get_drvdata(dev);

        /* Technically no need to read humidity as well */
        ret = sht15_update_measurements(data);

        return ret ? ret : sprintf(buf, "%d\n",
                                   sht15_calc_temp(data));
}

/**
 * sht15_show_humidity() - show humidity measurement value in sysfs
 * @dev:        device.
 * @attr:       device attribute.
 * @buf:        sysfs buffer where measurement values are written to.
 *
 * Will be called on read access to humidity1_input sysfs attribute.
 * Returns number of bytes written into buffer, negative errno on error.
 */
static ssize_t sht15_humidity_show(struct device *dev,
                                   struct device_attribute *attr, char *buf)
{
        int ret;
        struct sht15_data *data = dev_get_drvdata(dev);

        ret = sht15_update_measurements(data);

        return ret ? ret : sprintf(buf, "%d\n", sht15_calc_humid(data));
}

static ssize_t name_show(struct device *dev,
                         struct device_attribute *attr,
                         char *buf)
{
        struct platform_device *pdev = to_platform_device(dev);
        return sprintf(buf, "%s\n", pdev->name);
}

static SENSOR_DEVICE_ATTR_RO(temp1_input, sht15_temp, 0);
static SENSOR_DEVICE_ATTR_RO(humidity1_input, sht15_humidity, 0);
static SENSOR_DEVICE_ATTR_RO(temp1_fault, sht15_status,
                             SHT15_STATUS_LOW_BATTERY);
static SENSOR_DEVICE_ATTR_RO(humidity1_fault, sht15_status,
                             SHT15_STATUS_LOW_BATTERY);
static SENSOR_DEVICE_ATTR_RW(heater_enable, sht15_status, SHT15_STATUS_HEATER);
static DEVICE_ATTR_RO(name);
static struct attribute *sht15_attrs[] = {
        &sensor_dev_attr_temp1_input.dev_attr.attr,
        &sensor_dev_attr_humidity1_input.dev_attr.attr,
        &sensor_dev_attr_temp1_fault.dev_attr.attr,
        &sensor_dev_attr_humidity1_fault.dev_attr.attr,
        &sensor_dev_attr_heater_enable.dev_attr.attr,
        &dev_attr_name.attr,
        NULL,
};

static const struct attribute_group sht15_attr_group = {
        .attrs = sht15_attrs,
};

static irqreturn_t sht15_interrupt_fired(int irq, void *d)
{
        struct sht15_data *data = d;

        /* First disable the interrupt */
        disable_irq_nosync(irq);
        atomic_inc(&data->interrupt_handled);
        /* Then schedule a reading work struct */
        if (data->state != SHT15_READING_NOTHING)
                schedule_work(&data->read_work);
        return IRQ_HANDLED;
}

static void sht15_bh_read_data(struct work_struct *work_s)
{
        uint16_t val = 0;
        u8 dev_checksum = 0;
        u8 checksum_vals[3];
        struct sht15_data *data
                = container_of(work_s, struct sht15_data,
                               read_work);

        /* Firstly, verify the line is low */
        if (gpiod_get_value(data->data)) {
                /*
                 * If not, then start the interrupt again - care here as could
                 * have gone low in meantime so verify it hasn't!
                 */
                atomic_set(&data->interrupt_handled, 0);
                enable_irq(gpiod_to_irq(data->data));
                /* If still not occurred or another handler was scheduled */
                if (gpiod_get_value(data->data)
                    || atomic_read(&data->interrupt_handled))
                        return;
        }

        /* Read the data back from the device */
        val = sht15_read_byte(data);
        val <<= 8;
        if (sht15_ack(data))
                goto wakeup;
        val |= sht15_read_byte(data);

        if (data->checksumming) {
                /*
                 * Ask the device for a checksum and read it back.
                 * Note: the device sends the checksum byte reversed.
                 */
                if (sht15_ack(data))
                        goto wakeup;
                dev_checksum = bitrev8(sht15_read_byte(data));
                checksum_vals[0] = (data->state == SHT15_READING_TEMP) ?
                        SHT15_MEASURE_TEMP : SHT15_MEASURE_RH;
                checksum_vals[1] = (u8) (val >> 8);
                checksum_vals[2] = (u8) val;
                data->checksum_ok
                        = (sht15_crc8(data, checksum_vals, 3) == dev_checksum);
        }

        /* Tell the device we are done */
        if (sht15_end_transmission(data))
                goto wakeup;

        switch (data->state) {
        case SHT15_READING_TEMP:
                data->val_temp = val;
                break;
        case SHT15_READING_HUMID:
                data->val_humid = val;
                break;
        default:
                break;
        }

        data->state = SHT15_READING_NOTHING;
wakeup:
        wake_up(&data->wait_queue);
}

static void sht15_update_voltage(struct work_struct *work_s)
{
        struct sht15_data *data
                = container_of(work_s, struct sht15_data,
                               update_supply_work);
        data->supply_uv = regulator_get_voltage(data->reg);
}

/**
 * sht15_invalidate_voltage() - mark supply voltage invalid when notified by reg
 * @nb:         associated notification structure
 * @event:      voltage regulator state change event code
 * @ignored:    function parameter - ignored here
 *
 * Note that as the notification code holds the regulator lock, we have
 * to schedule an update of the supply voltage rather than getting it directly.
 */
static int sht15_invalidate_voltage(struct notifier_block *nb,
                                    unsigned long event,
                                    void *ignored)
{
        struct sht15_data *data = container_of(nb, struct sht15_data, nb);

        if (event == REGULATOR_EVENT_VOLTAGE_CHANGE)
                data->supply_uv_valid = false;
        schedule_work(&data->update_supply_work);

        return NOTIFY_OK;
}

#ifdef CONFIG_OF
static const struct of_device_id sht15_dt_match[] = {
        { .compatible = "sensirion,sht15" },
        { },
};
MODULE_DEVICE_TABLE(of, sht15_dt_match);
#endif

static int sht15_probe(struct platform_device *pdev)
{
        int ret;
        struct sht15_data *data;

        data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
        if (!data)
                return -ENOMEM;

        INIT_WORK(&data->read_work, sht15_bh_read_data);
        INIT_WORK(&data->update_supply_work, sht15_update_voltage);
        platform_set_drvdata(pdev, data);
        mutex_init(&data->read_lock);
        data->dev = &pdev->dev;
        init_waitqueue_head(&data->wait_queue);

        /*
         * If a regulator is available,
         * query what the supply voltage actually is!
         */
        data->reg = devm_regulator_get_optional(data->dev, "vcc");
        if (!IS_ERR(data->reg)) {
                int voltage;

                voltage = regulator_get_voltage(data->reg);
                if (voltage)
                        data->supply_uv = voltage;

                ret = regulator_enable(data->reg);
                if (ret != 0) {
                        dev_err(&pdev->dev,
                                "failed to enable regulator: %d\n", ret);
                        return ret;
                }

                /*
                 * Setup a notifier block to update this if another device
                 * causes the voltage to change
                 */
                data->nb.notifier_call = &sht15_invalidate_voltage;
                ret = regulator_register_notifier(data->reg, &data->nb);
                if (ret) {
                        dev_err(&pdev->dev,
                                "regulator notifier request failed\n");
                        regulator_disable(data->reg);
                        return ret;
                }
        }

        /* Try requesting the GPIOs */
        data->sck = devm_gpiod_get(&pdev->dev, "clk", GPIOD_OUT_LOW);
        if (IS_ERR(data->sck)) {
                ret = PTR_ERR(data->sck);
                dev_err(&pdev->dev, "clock line GPIO request failed\n");
                goto err_release_reg;
        }
        data->data = devm_gpiod_get(&pdev->dev, "data", GPIOD_IN);
        if (IS_ERR(data->data)) {
                ret = PTR_ERR(data->data);
                dev_err(&pdev->dev, "data line GPIO request failed\n");
                goto err_release_reg;
        }

        ret = devm_request_irq(&pdev->dev, gpiod_to_irq(data->data),
                               sht15_interrupt_fired,
                               IRQF_TRIGGER_FALLING,
                               "sht15 data",
                               data);
        if (ret) {
                dev_err(&pdev->dev, "failed to get irq for data line\n");
                goto err_release_reg;
        }
        disable_irq_nosync(gpiod_to_irq(data->data));
        ret = sht15_connection_reset(data);
        if (ret)
                goto err_release_reg;
        ret = sht15_soft_reset(data);
        if (ret)
                goto err_release_reg;

        ret = sysfs_create_group(&pdev->dev.kobj, &sht15_attr_group);
        if (ret) {
                dev_err(&pdev->dev, "sysfs create failed\n");
                goto err_release_reg;
        }

        data->hwmon_dev = hwmon_device_register(data->dev);
        if (IS_ERR(data->hwmon_dev)) {
                ret = PTR_ERR(data->hwmon_dev);
                goto err_release_sysfs_group;
        }

        return 0;

err_release_sysfs_group:
        sysfs_remove_group(&pdev->dev.kobj, &sht15_attr_group);
err_release_reg:
        if (!IS_ERR(data->reg)) {
                regulator_unregister_notifier(data->reg, &data->nb);
                regulator_disable(data->reg);
        }
        return ret;
}

static int sht15_remove(struct platform_device *pdev)
{
        struct sht15_data *data = platform_get_drvdata(pdev);

        /*
         * Make sure any reads from the device are done and
         * prevent new ones beginning
         */
        mutex_lock(&data->read_lock);
        if (sht15_soft_reset(data)) {
                mutex_unlock(&data->read_lock);
                return -EFAULT;
        }
        hwmon_device_unregister(data->hwmon_dev);
        sysfs_remove_group(&pdev->dev.kobj, &sht15_attr_group);
        if (!IS_ERR(data->reg)) {
                regulator_unregister_notifier(data->reg, &data->nb);
                regulator_disable(data->reg);
        }

        mutex_unlock(&data->read_lock);

        return 0;
}

static const struct platform_device_id sht15_device_ids[] = {
        { "sht10", sht10 },
        { "sht11", sht11 },
        { "sht15", sht15 },
        { "sht71", sht71 },
        { "sht75", sht75 },
        { }
};
MODULE_DEVICE_TABLE(platform, sht15_device_ids);

static struct platform_driver sht15_driver = {
        .driver = {
                .name = "sht15",
                .of_match_table = of_match_ptr(sht15_dt_match),
        },
        .probe = sht15_probe,
        .remove = sht15_remove,
        .id_table = sht15_device_ids,
};
module_platform_driver(sht15_driver);

MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Sensirion SHT15 temperature and humidity sensor driver");