linux/drivers/mmc/host/meson-gx-mmc.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0-only
   2/*
   3 * Amlogic SD/eMMC driver for the GX/S905 family SoCs
   4 *
   5 * Copyright (c) 2016 BayLibre, SAS.
   6 * Author: Kevin Hilman <khilman@baylibre.com>
   7 */
   8#include <linux/kernel.h>
   9#include <linux/module.h>
  10#include <linux/init.h>
  11#include <linux/delay.h>
  12#include <linux/device.h>
  13#include <linux/iopoll.h>
  14#include <linux/of_device.h>
  15#include <linux/platform_device.h>
  16#include <linux/ioport.h>
  17#include <linux/dma-mapping.h>
  18#include <linux/mmc/host.h>
  19#include <linux/mmc/mmc.h>
  20#include <linux/mmc/sdio.h>
  21#include <linux/mmc/slot-gpio.h>
  22#include <linux/io.h>
  23#include <linux/clk.h>
  24#include <linux/clk-provider.h>
  25#include <linux/regulator/consumer.h>
  26#include <linux/reset.h>
  27#include <linux/interrupt.h>
  28#include <linux/bitfield.h>
  29#include <linux/pinctrl/consumer.h>
  30
  31#define DRIVER_NAME "meson-gx-mmc"
  32
  33#define SD_EMMC_CLOCK 0x0
  34#define   CLK_DIV_MASK GENMASK(5, 0)
  35#define   CLK_SRC_MASK GENMASK(7, 6)
  36#define   CLK_CORE_PHASE_MASK GENMASK(9, 8)
  37#define   CLK_TX_PHASE_MASK GENMASK(11, 10)
  38#define   CLK_RX_PHASE_MASK GENMASK(13, 12)
  39#define   CLK_PHASE_0 0
  40#define   CLK_PHASE_180 2
  41#define   CLK_V2_TX_DELAY_MASK GENMASK(19, 16)
  42#define   CLK_V2_RX_DELAY_MASK GENMASK(23, 20)
  43#define   CLK_V2_ALWAYS_ON BIT(24)
  44
  45#define   CLK_V3_TX_DELAY_MASK GENMASK(21, 16)
  46#define   CLK_V3_RX_DELAY_MASK GENMASK(27, 22)
  47#define   CLK_V3_ALWAYS_ON BIT(28)
  48
  49#define   CLK_TX_DELAY_MASK(h)          (h->data->tx_delay_mask)
  50#define   CLK_RX_DELAY_MASK(h)          (h->data->rx_delay_mask)
  51#define   CLK_ALWAYS_ON(h)              (h->data->always_on)
  52
  53#define SD_EMMC_DELAY 0x4
  54#define SD_EMMC_ADJUST 0x8
  55#define   ADJUST_ADJ_DELAY_MASK GENMASK(21, 16)
  56#define   ADJUST_DS_EN BIT(15)
  57#define   ADJUST_ADJ_EN BIT(13)
  58
  59#define SD_EMMC_DELAY1 0x4
  60#define SD_EMMC_DELAY2 0x8
  61#define SD_EMMC_V3_ADJUST 0xc
  62
  63#define SD_EMMC_CALOUT 0x10
  64#define SD_EMMC_START 0x40
  65#define   START_DESC_INIT BIT(0)
  66#define   START_DESC_BUSY BIT(1)
  67#define   START_DESC_ADDR_MASK GENMASK(31, 2)
  68
  69#define SD_EMMC_CFG 0x44
  70#define   CFG_BUS_WIDTH_MASK GENMASK(1, 0)
  71#define   CFG_BUS_WIDTH_1 0x0
  72#define   CFG_BUS_WIDTH_4 0x1
  73#define   CFG_BUS_WIDTH_8 0x2
  74#define   CFG_DDR BIT(2)
  75#define   CFG_BLK_LEN_MASK GENMASK(7, 4)
  76#define   CFG_RESP_TIMEOUT_MASK GENMASK(11, 8)
  77#define   CFG_RC_CC_MASK GENMASK(15, 12)
  78#define   CFG_STOP_CLOCK BIT(22)
  79#define   CFG_CLK_ALWAYS_ON BIT(18)
  80#define   CFG_CHK_DS BIT(20)
  81#define   CFG_AUTO_CLK BIT(23)
  82#define   CFG_ERR_ABORT BIT(27)
  83
  84#define SD_EMMC_STATUS 0x48
  85#define   STATUS_BUSY BIT(31)
  86#define   STATUS_DESC_BUSY BIT(30)
  87#define   STATUS_DATI GENMASK(23, 16)
  88
  89#define SD_EMMC_IRQ_EN 0x4c
  90#define   IRQ_RXD_ERR_MASK GENMASK(7, 0)
  91#define   IRQ_TXD_ERR BIT(8)
  92#define   IRQ_DESC_ERR BIT(9)
  93#define   IRQ_RESP_ERR BIT(10)
  94#define   IRQ_CRC_ERR \
  95        (IRQ_RXD_ERR_MASK | IRQ_TXD_ERR | IRQ_DESC_ERR | IRQ_RESP_ERR)
  96#define   IRQ_RESP_TIMEOUT BIT(11)
  97#define   IRQ_DESC_TIMEOUT BIT(12)
  98#define   IRQ_TIMEOUTS \
  99        (IRQ_RESP_TIMEOUT | IRQ_DESC_TIMEOUT)
 100#define   IRQ_END_OF_CHAIN BIT(13)
 101#define   IRQ_RESP_STATUS BIT(14)
 102#define   IRQ_SDIO BIT(15)
 103#define   IRQ_EN_MASK \
 104        (IRQ_CRC_ERR | IRQ_TIMEOUTS | IRQ_END_OF_CHAIN | IRQ_RESP_STATUS |\
 105         IRQ_SDIO)
 106
 107#define SD_EMMC_CMD_CFG 0x50
 108#define SD_EMMC_CMD_ARG 0x54
 109#define SD_EMMC_CMD_DAT 0x58
 110#define SD_EMMC_CMD_RSP 0x5c
 111#define SD_EMMC_CMD_RSP1 0x60
 112#define SD_EMMC_CMD_RSP2 0x64
 113#define SD_EMMC_CMD_RSP3 0x68
 114
 115#define SD_EMMC_RXD 0x94
 116#define SD_EMMC_TXD 0x94
 117#define SD_EMMC_LAST_REG SD_EMMC_TXD
 118
 119#define SD_EMMC_SRAM_DATA_BUF_LEN 1536
 120#define SD_EMMC_SRAM_DATA_BUF_OFF 0x200
 121
 122#define SD_EMMC_CFG_BLK_SIZE 512 /* internal buffer max: 512 bytes */
 123#define SD_EMMC_CFG_RESP_TIMEOUT 256 /* in clock cycles */
 124#define SD_EMMC_CMD_TIMEOUT 1024 /* in ms */
 125#define SD_EMMC_CMD_TIMEOUT_DATA 4096 /* in ms */
 126#define SD_EMMC_CFG_CMD_GAP 16 /* in clock cycles */
 127#define SD_EMMC_DESC_BUF_LEN PAGE_SIZE
 128
 129#define SD_EMMC_PRE_REQ_DONE BIT(0)
 130#define SD_EMMC_DESC_CHAIN_MODE BIT(1)
 131
 132#define MUX_CLK_NUM_PARENTS 2
 133
 134struct meson_mmc_data {
 135        unsigned int tx_delay_mask;
 136        unsigned int rx_delay_mask;
 137        unsigned int always_on;
 138        unsigned int adjust;
 139};
 140
 141struct sd_emmc_desc {
 142        u32 cmd_cfg;
 143        u32 cmd_arg;
 144        u32 cmd_data;
 145        u32 cmd_resp;
 146};
 147
 148struct meson_host {
 149        struct  device          *dev;
 150        struct  meson_mmc_data *data;
 151        struct  mmc_host        *mmc;
 152        struct  mmc_command     *cmd;
 153
 154        void __iomem *regs;
 155        struct clk *core_clk;
 156        struct clk *mux_clk;
 157        struct clk *mmc_clk;
 158        unsigned long req_rate;
 159        bool ddr;
 160
 161        bool dram_access_quirk;
 162
 163        struct pinctrl *pinctrl;
 164        struct pinctrl_state *pins_default;
 165        struct pinctrl_state *pins_clk_gate;
 166
 167        unsigned int bounce_buf_size;
 168        void *bounce_buf;
 169        dma_addr_t bounce_dma_addr;
 170        struct sd_emmc_desc *descs;
 171        dma_addr_t descs_dma_addr;
 172
 173        int irq;
 174
 175        bool vqmmc_enabled;
 176};
 177
 178#define CMD_CFG_LENGTH_MASK GENMASK(8, 0)
 179#define CMD_CFG_BLOCK_MODE BIT(9)
 180#define CMD_CFG_R1B BIT(10)
 181#define CMD_CFG_END_OF_CHAIN BIT(11)
 182#define CMD_CFG_TIMEOUT_MASK GENMASK(15, 12)
 183#define CMD_CFG_NO_RESP BIT(16)
 184#define CMD_CFG_NO_CMD BIT(17)
 185#define CMD_CFG_DATA_IO BIT(18)
 186#define CMD_CFG_DATA_WR BIT(19)
 187#define CMD_CFG_RESP_NOCRC BIT(20)
 188#define CMD_CFG_RESP_128 BIT(21)
 189#define CMD_CFG_RESP_NUM BIT(22)
 190#define CMD_CFG_DATA_NUM BIT(23)
 191#define CMD_CFG_CMD_INDEX_MASK GENMASK(29, 24)
 192#define CMD_CFG_ERROR BIT(30)
 193#define CMD_CFG_OWNER BIT(31)
 194
 195#define CMD_DATA_MASK GENMASK(31, 2)
 196#define CMD_DATA_BIG_ENDIAN BIT(1)
 197#define CMD_DATA_SRAM BIT(0)
 198#define CMD_RESP_MASK GENMASK(31, 1)
 199#define CMD_RESP_SRAM BIT(0)
 200
 201static unsigned int meson_mmc_get_timeout_msecs(struct mmc_data *data)
 202{
 203        unsigned int timeout = data->timeout_ns / NSEC_PER_MSEC;
 204
 205        if (!timeout)
 206                return SD_EMMC_CMD_TIMEOUT_DATA;
 207
 208        timeout = roundup_pow_of_two(timeout);
 209
 210        return min(timeout, 32768U); /* max. 2^15 ms */
 211}
 212
 213static struct mmc_command *meson_mmc_get_next_command(struct mmc_command *cmd)
 214{
 215        if (cmd->opcode == MMC_SET_BLOCK_COUNT && !cmd->error)
 216                return cmd->mrq->cmd;
 217        else if (mmc_op_multi(cmd->opcode) &&
 218                 (!cmd->mrq->sbc || cmd->error || cmd->data->error))
 219                return cmd->mrq->stop;
 220        else
 221                return NULL;
 222}
 223
 224static void meson_mmc_get_transfer_mode(struct mmc_host *mmc,
 225                                        struct mmc_request *mrq)
 226{
 227        struct meson_host *host = mmc_priv(mmc);
 228        struct mmc_data *data = mrq->data;
 229        struct scatterlist *sg;
 230        int i;
 231        bool use_desc_chain_mode = true;
 232
 233        /*
 234         * When Controller DMA cannot directly access DDR memory, disable
 235         * support for Chain Mode to directly use the internal SRAM using
 236         * the bounce buffer mode.
 237         */
 238        if (host->dram_access_quirk)
 239                return;
 240
 241        /*
 242         * Broken SDIO with AP6255-based WiFi on Khadas VIM Pro has been
 243         * reported. For some strange reason this occurs in descriptor
 244         * chain mode only. So let's fall back to bounce buffer mode
 245         * for command SD_IO_RW_EXTENDED.
 246         */
 247        if (mrq->cmd->opcode == SD_IO_RW_EXTENDED)
 248                return;
 249
 250        for_each_sg(data->sg, sg, data->sg_len, i)
 251                /* check for 8 byte alignment */
 252                if (sg->offset & 7) {
 253                        WARN_ONCE(1, "unaligned scatterlist buffer\n");
 254                        use_desc_chain_mode = false;
 255                        break;
 256                }
 257
 258        if (use_desc_chain_mode)
 259                data->host_cookie |= SD_EMMC_DESC_CHAIN_MODE;
 260}
 261
 262static inline bool meson_mmc_desc_chain_mode(const struct mmc_data *data)
 263{
 264        return data->host_cookie & SD_EMMC_DESC_CHAIN_MODE;
 265}
 266
 267static inline bool meson_mmc_bounce_buf_read(const struct mmc_data *data)
 268{
 269        return data && data->flags & MMC_DATA_READ &&
 270               !meson_mmc_desc_chain_mode(data);
 271}
 272
 273static void meson_mmc_pre_req(struct mmc_host *mmc, struct mmc_request *mrq)
 274{
 275        struct mmc_data *data = mrq->data;
 276
 277        if (!data)
 278                return;
 279
 280        meson_mmc_get_transfer_mode(mmc, mrq);
 281        data->host_cookie |= SD_EMMC_PRE_REQ_DONE;
 282
 283        if (!meson_mmc_desc_chain_mode(data))
 284                return;
 285
 286        data->sg_count = dma_map_sg(mmc_dev(mmc), data->sg, data->sg_len,
 287                                   mmc_get_dma_dir(data));
 288        if (!data->sg_count)
 289                dev_err(mmc_dev(mmc), "dma_map_sg failed");
 290}
 291
 292static void meson_mmc_post_req(struct mmc_host *mmc, struct mmc_request *mrq,
 293                               int err)
 294{
 295        struct mmc_data *data = mrq->data;
 296
 297        if (data && meson_mmc_desc_chain_mode(data) && data->sg_count)
 298                dma_unmap_sg(mmc_dev(mmc), data->sg, data->sg_len,
 299                             mmc_get_dma_dir(data));
 300}
 301
 302/*
 303 * Gating the clock on this controller is tricky.  It seems the mmc clock
 304 * is also used by the controller.  It may crash during some operation if the
 305 * clock is stopped.  The safest thing to do, whenever possible, is to keep
 306 * clock running at stop it at the pad using the pinmux.
 307 */
 308static void meson_mmc_clk_gate(struct meson_host *host)
 309{
 310        u32 cfg;
 311
 312        if (host->pins_clk_gate) {
 313                pinctrl_select_state(host->pinctrl, host->pins_clk_gate);
 314        } else {
 315                /*
 316                 * If the pinmux is not provided - default to the classic and
 317                 * unsafe method
 318                 */
 319                cfg = readl(host->regs + SD_EMMC_CFG);
 320                cfg |= CFG_STOP_CLOCK;
 321                writel(cfg, host->regs + SD_EMMC_CFG);
 322        }
 323}
 324
 325static void meson_mmc_clk_ungate(struct meson_host *host)
 326{
 327        u32 cfg;
 328
 329        if (host->pins_clk_gate)
 330                pinctrl_select_state(host->pinctrl, host->pins_default);
 331
 332        /* Make sure the clock is not stopped in the controller */
 333        cfg = readl(host->regs + SD_EMMC_CFG);
 334        cfg &= ~CFG_STOP_CLOCK;
 335        writel(cfg, host->regs + SD_EMMC_CFG);
 336}
 337
 338static int meson_mmc_clk_set(struct meson_host *host, unsigned long rate,
 339                             bool ddr)
 340{
 341        struct mmc_host *mmc = host->mmc;
 342        int ret;
 343        u32 cfg;
 344
 345        /* Same request - bail-out */
 346        if (host->ddr == ddr && host->req_rate == rate)
 347                return 0;
 348
 349        /* stop clock */
 350        meson_mmc_clk_gate(host);
 351        host->req_rate = 0;
 352        mmc->actual_clock = 0;
 353
 354        /* return with clock being stopped */
 355        if (!rate)
 356                return 0;
 357
 358        /* Stop the clock during rate change to avoid glitches */
 359        cfg = readl(host->regs + SD_EMMC_CFG);
 360        cfg |= CFG_STOP_CLOCK;
 361        writel(cfg, host->regs + SD_EMMC_CFG);
 362
 363        if (ddr) {
 364                /* DDR modes require higher module clock */
 365                rate <<= 1;
 366                cfg |= CFG_DDR;
 367        } else {
 368                cfg &= ~CFG_DDR;
 369        }
 370        writel(cfg, host->regs + SD_EMMC_CFG);
 371        host->ddr = ddr;
 372
 373        ret = clk_set_rate(host->mmc_clk, rate);
 374        if (ret) {
 375                dev_err(host->dev, "Unable to set cfg_div_clk to %lu. ret=%d\n",
 376                        rate, ret);
 377                return ret;
 378        }
 379
 380        host->req_rate = rate;
 381        mmc->actual_clock = clk_get_rate(host->mmc_clk);
 382
 383        /* We should report the real output frequency of the controller */
 384        if (ddr) {
 385                host->req_rate >>= 1;
 386                mmc->actual_clock >>= 1;
 387        }
 388
 389        dev_dbg(host->dev, "clk rate: %u Hz\n", mmc->actual_clock);
 390        if (rate != mmc->actual_clock)
 391                dev_dbg(host->dev, "requested rate was %lu\n", rate);
 392
 393        /* (re)start clock */
 394        meson_mmc_clk_ungate(host);
 395
 396        return 0;
 397}
 398
 399/*
 400 * The SD/eMMC IP block has an internal mux and divider used for
 401 * generating the MMC clock.  Use the clock framework to create and
 402 * manage these clocks.
 403 */
 404static int meson_mmc_clk_init(struct meson_host *host)
 405{
 406        struct clk_init_data init;
 407        struct clk_mux *mux;
 408        struct clk_divider *div;
 409        char clk_name[32];
 410        int i, ret = 0;
 411        const char *mux_parent_names[MUX_CLK_NUM_PARENTS];
 412        const char *clk_parent[1];
 413        u32 clk_reg;
 414
 415        /* init SD_EMMC_CLOCK to sane defaults w/min clock rate */
 416        clk_reg = CLK_ALWAYS_ON(host);
 417        clk_reg |= CLK_DIV_MASK;
 418        clk_reg |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
 419        clk_reg |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_0);
 420        clk_reg |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);
 421        writel(clk_reg, host->regs + SD_EMMC_CLOCK);
 422
 423        /* get the mux parents */
 424        for (i = 0; i < MUX_CLK_NUM_PARENTS; i++) {
 425                struct clk *clk;
 426                char name[16];
 427
 428                snprintf(name, sizeof(name), "clkin%d", i);
 429                clk = devm_clk_get(host->dev, name);
 430                if (IS_ERR(clk)) {
 431                        if (clk != ERR_PTR(-EPROBE_DEFER))
 432                                dev_err(host->dev, "Missing clock %s\n", name);
 433                        return PTR_ERR(clk);
 434                }
 435
 436                mux_parent_names[i] = __clk_get_name(clk);
 437        }
 438
 439        /* create the mux */
 440        mux = devm_kzalloc(host->dev, sizeof(*mux), GFP_KERNEL);
 441        if (!mux)
 442                return -ENOMEM;
 443
 444        snprintf(clk_name, sizeof(clk_name), "%s#mux", dev_name(host->dev));
 445        init.name = clk_name;
 446        init.ops = &clk_mux_ops;
 447        init.flags = 0;
 448        init.parent_names = mux_parent_names;
 449        init.num_parents = MUX_CLK_NUM_PARENTS;
 450
 451        mux->reg = host->regs + SD_EMMC_CLOCK;
 452        mux->shift = __ffs(CLK_SRC_MASK);
 453        mux->mask = CLK_SRC_MASK >> mux->shift;
 454        mux->hw.init = &init;
 455
 456        host->mux_clk = devm_clk_register(host->dev, &mux->hw);
 457        if (WARN_ON(IS_ERR(host->mux_clk)))
 458                return PTR_ERR(host->mux_clk);
 459
 460        /* create the divider */
 461        div = devm_kzalloc(host->dev, sizeof(*div), GFP_KERNEL);
 462        if (!div)
 463                return -ENOMEM;
 464
 465        snprintf(clk_name, sizeof(clk_name), "%s#div", dev_name(host->dev));
 466        init.name = clk_name;
 467        init.ops = &clk_divider_ops;
 468        init.flags = CLK_SET_RATE_PARENT;
 469        clk_parent[0] = __clk_get_name(host->mux_clk);
 470        init.parent_names = clk_parent;
 471        init.num_parents = 1;
 472
 473        div->reg = host->regs + SD_EMMC_CLOCK;
 474        div->shift = __ffs(CLK_DIV_MASK);
 475        div->width = __builtin_popcountl(CLK_DIV_MASK);
 476        div->hw.init = &init;
 477        div->flags = CLK_DIVIDER_ONE_BASED;
 478
 479        host->mmc_clk = devm_clk_register(host->dev, &div->hw);
 480        if (WARN_ON(IS_ERR(host->mmc_clk)))
 481                return PTR_ERR(host->mmc_clk);
 482
 483        /* init SD_EMMC_CLOCK to sane defaults w/min clock rate */
 484        host->mmc->f_min = clk_round_rate(host->mmc_clk, 400000);
 485        ret = clk_set_rate(host->mmc_clk, host->mmc->f_min);
 486        if (ret)
 487                return ret;
 488
 489        return clk_prepare_enable(host->mmc_clk);
 490}
 491
 492static void meson_mmc_disable_resampling(struct meson_host *host)
 493{
 494        unsigned int val = readl(host->regs + host->data->adjust);
 495
 496        val &= ~ADJUST_ADJ_EN;
 497        writel(val, host->regs + host->data->adjust);
 498}
 499
 500static void meson_mmc_reset_resampling(struct meson_host *host)
 501{
 502        unsigned int val;
 503
 504        meson_mmc_disable_resampling(host);
 505
 506        val = readl(host->regs + host->data->adjust);
 507        val &= ~ADJUST_ADJ_DELAY_MASK;
 508        writel(val, host->regs + host->data->adjust);
 509}
 510
 511static int meson_mmc_resampling_tuning(struct mmc_host *mmc, u32 opcode)
 512{
 513        struct meson_host *host = mmc_priv(mmc);
 514        unsigned int val, dly, max_dly, i;
 515        int ret;
 516
 517        /* Resampling is done using the source clock */
 518        max_dly = DIV_ROUND_UP(clk_get_rate(host->mux_clk),
 519                               clk_get_rate(host->mmc_clk));
 520
 521        val = readl(host->regs + host->data->adjust);
 522        val |= ADJUST_ADJ_EN;
 523        writel(val, host->regs + host->data->adjust);
 524
 525        if (mmc->doing_retune)
 526                dly = FIELD_GET(ADJUST_ADJ_DELAY_MASK, val) + 1;
 527        else
 528                dly = 0;
 529
 530        for (i = 0; i < max_dly; i++) {
 531                val &= ~ADJUST_ADJ_DELAY_MASK;
 532                val |= FIELD_PREP(ADJUST_ADJ_DELAY_MASK, (dly + i) % max_dly);
 533                writel(val, host->regs + host->data->adjust);
 534
 535                ret = mmc_send_tuning(mmc, opcode, NULL);
 536                if (!ret) {
 537                        dev_dbg(mmc_dev(mmc), "resampling delay: %u\n",
 538                                (dly + i) % max_dly);
 539                        return 0;
 540                }
 541        }
 542
 543        meson_mmc_reset_resampling(host);
 544        return -EIO;
 545}
 546
 547static int meson_mmc_prepare_ios_clock(struct meson_host *host,
 548                                       struct mmc_ios *ios)
 549{
 550        bool ddr;
 551
 552        switch (ios->timing) {
 553        case MMC_TIMING_MMC_DDR52:
 554        case MMC_TIMING_UHS_DDR50:
 555                ddr = true;
 556                break;
 557
 558        default:
 559                ddr = false;
 560                break;
 561        }
 562
 563        return meson_mmc_clk_set(host, ios->clock, ddr);
 564}
 565
 566static void meson_mmc_check_resampling(struct meson_host *host,
 567                                       struct mmc_ios *ios)
 568{
 569        switch (ios->timing) {
 570        case MMC_TIMING_LEGACY:
 571        case MMC_TIMING_MMC_HS:
 572        case MMC_TIMING_SD_HS:
 573        case MMC_TIMING_MMC_DDR52:
 574                meson_mmc_disable_resampling(host);
 575                break;
 576        }
 577}
 578
 579static void meson_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 580{
 581        struct meson_host *host = mmc_priv(mmc);
 582        u32 bus_width, val;
 583        int err;
 584
 585        /*
 586         * GPIO regulator, only controls switching between 1v8 and
 587         * 3v3, doesn't support MMC_POWER_OFF, MMC_POWER_ON.
 588         */
 589        switch (ios->power_mode) {
 590        case MMC_POWER_OFF:
 591                if (!IS_ERR(mmc->supply.vmmc))
 592                        mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
 593
 594                if (!IS_ERR(mmc->supply.vqmmc) && host->vqmmc_enabled) {
 595                        regulator_disable(mmc->supply.vqmmc);
 596                        host->vqmmc_enabled = false;
 597                }
 598
 599                break;
 600
 601        case MMC_POWER_UP:
 602                if (!IS_ERR(mmc->supply.vmmc))
 603                        mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd);
 604
 605                break;
 606
 607        case MMC_POWER_ON:
 608                if (!IS_ERR(mmc->supply.vqmmc) && !host->vqmmc_enabled) {
 609                        int ret = regulator_enable(mmc->supply.vqmmc);
 610
 611                        if (ret < 0)
 612                                dev_err(host->dev,
 613                                        "failed to enable vqmmc regulator\n");
 614                        else
 615                                host->vqmmc_enabled = true;
 616                }
 617
 618                break;
 619        }
 620
 621        /* Bus width */
 622        switch (ios->bus_width) {
 623        case MMC_BUS_WIDTH_1:
 624                bus_width = CFG_BUS_WIDTH_1;
 625                break;
 626        case MMC_BUS_WIDTH_4:
 627                bus_width = CFG_BUS_WIDTH_4;
 628                break;
 629        case MMC_BUS_WIDTH_8:
 630                bus_width = CFG_BUS_WIDTH_8;
 631                break;
 632        default:
 633                dev_err(host->dev, "Invalid ios->bus_width: %u.  Setting to 4.\n",
 634                        ios->bus_width);
 635                bus_width = CFG_BUS_WIDTH_4;
 636        }
 637
 638        val = readl(host->regs + SD_EMMC_CFG);
 639        val &= ~CFG_BUS_WIDTH_MASK;
 640        val |= FIELD_PREP(CFG_BUS_WIDTH_MASK, bus_width);
 641        writel(val, host->regs + SD_EMMC_CFG);
 642
 643        meson_mmc_check_resampling(host, ios);
 644        err = meson_mmc_prepare_ios_clock(host, ios);
 645        if (err)
 646                dev_err(host->dev, "Failed to set clock: %d\n,", err);
 647
 648        dev_dbg(host->dev, "SD_EMMC_CFG:  0x%08x\n", val);
 649}
 650
 651static void meson_mmc_request_done(struct mmc_host *mmc,
 652                                   struct mmc_request *mrq)
 653{
 654        struct meson_host *host = mmc_priv(mmc);
 655
 656        host->cmd = NULL;
 657        mmc_request_done(host->mmc, mrq);
 658}
 659
 660static void meson_mmc_set_blksz(struct mmc_host *mmc, unsigned int blksz)
 661{
 662        struct meson_host *host = mmc_priv(mmc);
 663        u32 cfg, blksz_old;
 664
 665        cfg = readl(host->regs + SD_EMMC_CFG);
 666        blksz_old = FIELD_GET(CFG_BLK_LEN_MASK, cfg);
 667
 668        if (!is_power_of_2(blksz))
 669                dev_err(host->dev, "blksz %u is not a power of 2\n", blksz);
 670
 671        blksz = ilog2(blksz);
 672
 673        /* check if block-size matches, if not update */
 674        if (blksz == blksz_old)
 675                return;
 676
 677        dev_dbg(host->dev, "%s: update blk_len %d -> %d\n", __func__,
 678                blksz_old, blksz);
 679
 680        cfg &= ~CFG_BLK_LEN_MASK;
 681        cfg |= FIELD_PREP(CFG_BLK_LEN_MASK, blksz);
 682        writel(cfg, host->regs + SD_EMMC_CFG);
 683}
 684
 685static void meson_mmc_set_response_bits(struct mmc_command *cmd, u32 *cmd_cfg)
 686{
 687        if (cmd->flags & MMC_RSP_PRESENT) {
 688                if (cmd->flags & MMC_RSP_136)
 689                        *cmd_cfg |= CMD_CFG_RESP_128;
 690                *cmd_cfg |= CMD_CFG_RESP_NUM;
 691
 692                if (!(cmd->flags & MMC_RSP_CRC))
 693                        *cmd_cfg |= CMD_CFG_RESP_NOCRC;
 694
 695                if (cmd->flags & MMC_RSP_BUSY)
 696                        *cmd_cfg |= CMD_CFG_R1B;
 697        } else {
 698                *cmd_cfg |= CMD_CFG_NO_RESP;
 699        }
 700}
 701
 702static void meson_mmc_desc_chain_transfer(struct mmc_host *mmc, u32 cmd_cfg)
 703{
 704        struct meson_host *host = mmc_priv(mmc);
 705        struct sd_emmc_desc *desc = host->descs;
 706        struct mmc_data *data = host->cmd->data;
 707        struct scatterlist *sg;
 708        u32 start;
 709        int i;
 710
 711        if (data->flags & MMC_DATA_WRITE)
 712                cmd_cfg |= CMD_CFG_DATA_WR;
 713
 714        if (data->blocks > 1) {
 715                cmd_cfg |= CMD_CFG_BLOCK_MODE;
 716                meson_mmc_set_blksz(mmc, data->blksz);
 717        }
 718
 719        for_each_sg(data->sg, sg, data->sg_count, i) {
 720                unsigned int len = sg_dma_len(sg);
 721
 722                if (data->blocks > 1)
 723                        len /= data->blksz;
 724
 725                desc[i].cmd_cfg = cmd_cfg;
 726                desc[i].cmd_cfg |= FIELD_PREP(CMD_CFG_LENGTH_MASK, len);
 727                if (i > 0)
 728                        desc[i].cmd_cfg |= CMD_CFG_NO_CMD;
 729                desc[i].cmd_arg = host->cmd->arg;
 730                desc[i].cmd_resp = 0;
 731                desc[i].cmd_data = sg_dma_address(sg);
 732        }
 733        desc[data->sg_count - 1].cmd_cfg |= CMD_CFG_END_OF_CHAIN;
 734
 735        dma_wmb(); /* ensure descriptor is written before kicked */
 736        start = host->descs_dma_addr | START_DESC_BUSY;
 737        writel(start, host->regs + SD_EMMC_START);
 738}
 739
 740static void meson_mmc_start_cmd(struct mmc_host *mmc, struct mmc_command *cmd)
 741{
 742        struct meson_host *host = mmc_priv(mmc);
 743        struct mmc_data *data = cmd->data;
 744        u32 cmd_cfg = 0, cmd_data = 0;
 745        unsigned int xfer_bytes = 0;
 746
 747        /* Setup descriptors */
 748        dma_rmb();
 749
 750        host->cmd = cmd;
 751
 752        cmd_cfg |= FIELD_PREP(CMD_CFG_CMD_INDEX_MASK, cmd->opcode);
 753        cmd_cfg |= CMD_CFG_OWNER;  /* owned by CPU */
 754        cmd_cfg |= CMD_CFG_ERROR; /* stop in case of error */
 755
 756        meson_mmc_set_response_bits(cmd, &cmd_cfg);
 757
 758        /* data? */
 759        if (data) {
 760                data->bytes_xfered = 0;
 761                cmd_cfg |= CMD_CFG_DATA_IO;
 762                cmd_cfg |= FIELD_PREP(CMD_CFG_TIMEOUT_MASK,
 763                                      ilog2(meson_mmc_get_timeout_msecs(data)));
 764
 765                if (meson_mmc_desc_chain_mode(data)) {
 766                        meson_mmc_desc_chain_transfer(mmc, cmd_cfg);
 767                        return;
 768                }
 769
 770                if (data->blocks > 1) {
 771                        cmd_cfg |= CMD_CFG_BLOCK_MODE;
 772                        cmd_cfg |= FIELD_PREP(CMD_CFG_LENGTH_MASK,
 773                                              data->blocks);
 774                        meson_mmc_set_blksz(mmc, data->blksz);
 775                } else {
 776                        cmd_cfg |= FIELD_PREP(CMD_CFG_LENGTH_MASK, data->blksz);
 777                }
 778
 779                xfer_bytes = data->blksz * data->blocks;
 780                if (data->flags & MMC_DATA_WRITE) {
 781                        cmd_cfg |= CMD_CFG_DATA_WR;
 782                        WARN_ON(xfer_bytes > host->bounce_buf_size);
 783                        sg_copy_to_buffer(data->sg, data->sg_len,
 784                                          host->bounce_buf, xfer_bytes);
 785                        dma_wmb();
 786                }
 787
 788                cmd_data = host->bounce_dma_addr & CMD_DATA_MASK;
 789        } else {
 790                cmd_cfg |= FIELD_PREP(CMD_CFG_TIMEOUT_MASK,
 791                                      ilog2(SD_EMMC_CMD_TIMEOUT));
 792        }
 793
 794        /* Last descriptor */
 795        cmd_cfg |= CMD_CFG_END_OF_CHAIN;
 796        writel(cmd_cfg, host->regs + SD_EMMC_CMD_CFG);
 797        writel(cmd_data, host->regs + SD_EMMC_CMD_DAT);
 798        writel(0, host->regs + SD_EMMC_CMD_RSP);
 799        wmb(); /* ensure descriptor is written before kicked */
 800        writel(cmd->arg, host->regs + SD_EMMC_CMD_ARG);
 801}
 802
 803static void meson_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
 804{
 805        struct meson_host *host = mmc_priv(mmc);
 806        bool needs_pre_post_req = mrq->data &&
 807                        !(mrq->data->host_cookie & SD_EMMC_PRE_REQ_DONE);
 808
 809        if (needs_pre_post_req) {
 810                meson_mmc_get_transfer_mode(mmc, mrq);
 811                if (!meson_mmc_desc_chain_mode(mrq->data))
 812                        needs_pre_post_req = false;
 813        }
 814
 815        if (needs_pre_post_req)
 816                meson_mmc_pre_req(mmc, mrq);
 817
 818        /* Stop execution */
 819        writel(0, host->regs + SD_EMMC_START);
 820
 821        meson_mmc_start_cmd(mmc, mrq->sbc ?: mrq->cmd);
 822
 823        if (needs_pre_post_req)
 824                meson_mmc_post_req(mmc, mrq, 0);
 825}
 826
 827static void meson_mmc_read_resp(struct mmc_host *mmc, struct mmc_command *cmd)
 828{
 829        struct meson_host *host = mmc_priv(mmc);
 830
 831        if (cmd->flags & MMC_RSP_136) {
 832                cmd->resp[0] = readl(host->regs + SD_EMMC_CMD_RSP3);
 833                cmd->resp[1] = readl(host->regs + SD_EMMC_CMD_RSP2);
 834                cmd->resp[2] = readl(host->regs + SD_EMMC_CMD_RSP1);
 835                cmd->resp[3] = readl(host->regs + SD_EMMC_CMD_RSP);
 836        } else if (cmd->flags & MMC_RSP_PRESENT) {
 837                cmd->resp[0] = readl(host->regs + SD_EMMC_CMD_RSP);
 838        }
 839}
 840
 841static irqreturn_t meson_mmc_irq(int irq, void *dev_id)
 842{
 843        struct meson_host *host = dev_id;
 844        struct mmc_command *cmd;
 845        struct mmc_data *data;
 846        u32 irq_en, status, raw_status;
 847        irqreturn_t ret = IRQ_NONE;
 848
 849        irq_en = readl(host->regs + SD_EMMC_IRQ_EN);
 850        raw_status = readl(host->regs + SD_EMMC_STATUS);
 851        status = raw_status & irq_en;
 852
 853        if (!status) {
 854                dev_dbg(host->dev,
 855                        "Unexpected IRQ! irq_en 0x%08x - status 0x%08x\n",
 856                         irq_en, raw_status);
 857                return IRQ_NONE;
 858        }
 859
 860        if (WARN_ON(!host) || WARN_ON(!host->cmd))
 861                return IRQ_NONE;
 862
 863        /* ack all raised interrupts */
 864        writel(status, host->regs + SD_EMMC_STATUS);
 865
 866        cmd = host->cmd;
 867        data = cmd->data;
 868        cmd->error = 0;
 869        if (status & IRQ_CRC_ERR) {
 870                dev_dbg(host->dev, "CRC Error - status 0x%08x\n", status);
 871                cmd->error = -EILSEQ;
 872                ret = IRQ_WAKE_THREAD;
 873                goto out;
 874        }
 875
 876        if (status & IRQ_TIMEOUTS) {
 877                dev_dbg(host->dev, "Timeout - status 0x%08x\n", status);
 878                cmd->error = -ETIMEDOUT;
 879                ret = IRQ_WAKE_THREAD;
 880                goto out;
 881        }
 882
 883        meson_mmc_read_resp(host->mmc, cmd);
 884
 885        if (status & IRQ_SDIO) {
 886                dev_dbg(host->dev, "IRQ: SDIO TODO.\n");
 887                ret = IRQ_HANDLED;
 888        }
 889
 890        if (status & (IRQ_END_OF_CHAIN | IRQ_RESP_STATUS)) {
 891                if (data && !cmd->error)
 892                        data->bytes_xfered = data->blksz * data->blocks;
 893                if (meson_mmc_bounce_buf_read(data) ||
 894                    meson_mmc_get_next_command(cmd))
 895                        ret = IRQ_WAKE_THREAD;
 896                else
 897                        ret = IRQ_HANDLED;
 898        }
 899
 900out:
 901        if (cmd->error) {
 902                /* Stop desc in case of errors */
 903                u32 start = readl(host->regs + SD_EMMC_START);
 904
 905                start &= ~START_DESC_BUSY;
 906                writel(start, host->regs + SD_EMMC_START);
 907        }
 908
 909        if (ret == IRQ_HANDLED)
 910                meson_mmc_request_done(host->mmc, cmd->mrq);
 911
 912        return ret;
 913}
 914
 915static int meson_mmc_wait_desc_stop(struct meson_host *host)
 916{
 917        u32 status;
 918
 919        /*
 920         * It may sometimes take a while for it to actually halt. Here, we
 921         * are giving it 5ms to comply
 922         *
 923         * If we don't confirm the descriptor is stopped, it might raise new
 924         * IRQs after we have called mmc_request_done() which is bad.
 925         */
 926
 927        return readl_poll_timeout(host->regs + SD_EMMC_STATUS, status,
 928                                  !(status & (STATUS_BUSY | STATUS_DESC_BUSY)),
 929                                  100, 5000);
 930}
 931
 932static irqreturn_t meson_mmc_irq_thread(int irq, void *dev_id)
 933{
 934        struct meson_host *host = dev_id;
 935        struct mmc_command *next_cmd, *cmd = host->cmd;
 936        struct mmc_data *data;
 937        unsigned int xfer_bytes;
 938
 939        if (WARN_ON(!cmd))
 940                return IRQ_NONE;
 941
 942        if (cmd->error) {
 943                meson_mmc_wait_desc_stop(host);
 944                meson_mmc_request_done(host->mmc, cmd->mrq);
 945
 946                return IRQ_HANDLED;
 947        }
 948
 949        data = cmd->data;
 950        if (meson_mmc_bounce_buf_read(data)) {
 951                xfer_bytes = data->blksz * data->blocks;
 952                WARN_ON(xfer_bytes > host->bounce_buf_size);
 953                sg_copy_from_buffer(data->sg, data->sg_len,
 954                                    host->bounce_buf, xfer_bytes);
 955        }
 956
 957        next_cmd = meson_mmc_get_next_command(cmd);
 958        if (next_cmd)
 959                meson_mmc_start_cmd(host->mmc, next_cmd);
 960        else
 961                meson_mmc_request_done(host->mmc, cmd->mrq);
 962
 963        return IRQ_HANDLED;
 964}
 965
 966/*
 967 * NOTE: we only need this until the GPIO/pinctrl driver can handle
 968 * interrupts.  For now, the MMC core will use this for polling.
 969 */
 970static int meson_mmc_get_cd(struct mmc_host *mmc)
 971{
 972        int status = mmc_gpio_get_cd(mmc);
 973
 974        if (status == -ENOSYS)
 975                return 1; /* assume present */
 976
 977        return status;
 978}
 979
 980static void meson_mmc_cfg_init(struct meson_host *host)
 981{
 982        u32 cfg = 0;
 983
 984        cfg |= FIELD_PREP(CFG_RESP_TIMEOUT_MASK,
 985                          ilog2(SD_EMMC_CFG_RESP_TIMEOUT));
 986        cfg |= FIELD_PREP(CFG_RC_CC_MASK, ilog2(SD_EMMC_CFG_CMD_GAP));
 987        cfg |= FIELD_PREP(CFG_BLK_LEN_MASK, ilog2(SD_EMMC_CFG_BLK_SIZE));
 988
 989        /* abort chain on R/W errors */
 990        cfg |= CFG_ERR_ABORT;
 991
 992        writel(cfg, host->regs + SD_EMMC_CFG);
 993}
 994
 995static int meson_mmc_card_busy(struct mmc_host *mmc)
 996{
 997        struct meson_host *host = mmc_priv(mmc);
 998        u32 regval;
 999
1000        regval = readl(host->regs + SD_EMMC_STATUS);
1001
1002        /* We are only interrested in lines 0 to 3, so mask the other ones */
1003        return !(FIELD_GET(STATUS_DATI, regval) & 0xf);
1004}
1005
1006static int meson_mmc_voltage_switch(struct mmc_host *mmc, struct mmc_ios *ios)
1007{
1008        /* vqmmc regulator is available */
1009        if (!IS_ERR(mmc->supply.vqmmc)) {
1010                /*
1011                 * The usual amlogic setup uses a GPIO to switch from one
1012                 * regulator to the other. While the voltage ramp up is
1013                 * pretty fast, care must be taken when switching from 3.3v
1014                 * to 1.8v. Please make sure the regulator framework is aware
1015                 * of your own regulator constraints
1016                 */
1017                return mmc_regulator_set_vqmmc(mmc, ios);
1018        }
1019
1020        /* no vqmmc regulator, assume fixed regulator at 3/3.3V */
1021        if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330)
1022                return 0;
1023
1024        return -EINVAL;
1025}
1026
1027static const struct mmc_host_ops meson_mmc_ops = {
1028        .request        = meson_mmc_request,
1029        .set_ios        = meson_mmc_set_ios,
1030        .get_cd         = meson_mmc_get_cd,
1031        .pre_req        = meson_mmc_pre_req,
1032        .post_req       = meson_mmc_post_req,
1033        .execute_tuning = meson_mmc_resampling_tuning,
1034        .card_busy      = meson_mmc_card_busy,
1035        .start_signal_voltage_switch = meson_mmc_voltage_switch,
1036};
1037
1038static int meson_mmc_probe(struct platform_device *pdev)
1039{
1040        struct resource *res;
1041        struct meson_host *host;
1042        struct mmc_host *mmc;
1043        int ret;
1044
1045        mmc = mmc_alloc_host(sizeof(struct meson_host), &pdev->dev);
1046        if (!mmc)
1047                return -ENOMEM;
1048        host = mmc_priv(mmc);
1049        host->mmc = mmc;
1050        host->dev = &pdev->dev;
1051        dev_set_drvdata(&pdev->dev, host);
1052
1053        /* The G12A SDIO Controller needs an SRAM bounce buffer */
1054        host->dram_access_quirk = device_property_read_bool(&pdev->dev,
1055                                        "amlogic,dram-access-quirk");
1056
1057        /* Get regulators and the supported OCR mask */
1058        host->vqmmc_enabled = false;
1059        ret = mmc_regulator_get_supply(mmc);
1060        if (ret)
1061                goto free_host;
1062
1063        ret = mmc_of_parse(mmc);
1064        if (ret) {
1065                if (ret != -EPROBE_DEFER)
1066                        dev_warn(&pdev->dev, "error parsing DT: %d\n", ret);
1067                goto free_host;
1068        }
1069
1070        host->data = (struct meson_mmc_data *)
1071                of_device_get_match_data(&pdev->dev);
1072        if (!host->data) {
1073                ret = -EINVAL;
1074                goto free_host;
1075        }
1076
1077        ret = device_reset_optional(&pdev->dev);
1078        if (ret) {
1079                if (ret != -EPROBE_DEFER)
1080                        dev_err(&pdev->dev, "device reset failed: %d\n", ret);
1081
1082                return ret;
1083        }
1084
1085        res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1086        host->regs = devm_ioremap_resource(&pdev->dev, res);
1087        if (IS_ERR(host->regs)) {
1088                ret = PTR_ERR(host->regs);
1089                goto free_host;
1090        }
1091
1092        host->irq = platform_get_irq(pdev, 0);
1093        if (host->irq <= 0) {
1094                dev_err(&pdev->dev, "failed to get interrupt resource.\n");
1095                ret = -EINVAL;
1096                goto free_host;
1097        }
1098
1099        host->pinctrl = devm_pinctrl_get(&pdev->dev);
1100        if (IS_ERR(host->pinctrl)) {
1101                ret = PTR_ERR(host->pinctrl);
1102                goto free_host;
1103        }
1104
1105        host->pins_default = pinctrl_lookup_state(host->pinctrl,
1106                                                  PINCTRL_STATE_DEFAULT);
1107        if (IS_ERR(host->pins_default)) {
1108                ret = PTR_ERR(host->pins_default);
1109                goto free_host;
1110        }
1111
1112        host->pins_clk_gate = pinctrl_lookup_state(host->pinctrl,
1113                                                   "clk-gate");
1114        if (IS_ERR(host->pins_clk_gate)) {
1115                dev_warn(&pdev->dev,
1116                         "can't get clk-gate pinctrl, using clk_stop bit\n");
1117                host->pins_clk_gate = NULL;
1118        }
1119
1120        host->core_clk = devm_clk_get(&pdev->dev, "core");
1121        if (IS_ERR(host->core_clk)) {
1122                ret = PTR_ERR(host->core_clk);
1123                goto free_host;
1124        }
1125
1126        ret = clk_prepare_enable(host->core_clk);
1127        if (ret)
1128                goto free_host;
1129
1130        ret = meson_mmc_clk_init(host);
1131        if (ret)
1132                goto err_core_clk;
1133
1134        /* set config to sane default */
1135        meson_mmc_cfg_init(host);
1136
1137        /* Stop execution */
1138        writel(0, host->regs + SD_EMMC_START);
1139
1140        /* clear, ack and enable interrupts */
1141        writel(0, host->regs + SD_EMMC_IRQ_EN);
1142        writel(IRQ_CRC_ERR | IRQ_TIMEOUTS | IRQ_END_OF_CHAIN,
1143               host->regs + SD_EMMC_STATUS);
1144        writel(IRQ_CRC_ERR | IRQ_TIMEOUTS | IRQ_END_OF_CHAIN,
1145               host->regs + SD_EMMC_IRQ_EN);
1146
1147        ret = request_threaded_irq(host->irq, meson_mmc_irq,
1148                                   meson_mmc_irq_thread, IRQF_ONESHOT,
1149                                   dev_name(&pdev->dev), host);
1150        if (ret)
1151                goto err_init_clk;
1152
1153        mmc->caps |= MMC_CAP_CMD23;
1154        if (host->dram_access_quirk) {
1155                /* Limit to the available sram memory */
1156                mmc->max_segs = SD_EMMC_SRAM_DATA_BUF_LEN / mmc->max_blk_size;
1157                mmc->max_blk_count = mmc->max_segs;
1158        } else {
1159                mmc->max_blk_count = CMD_CFG_LENGTH_MASK;
1160                mmc->max_segs = SD_EMMC_DESC_BUF_LEN /
1161                                sizeof(struct sd_emmc_desc);
1162        }
1163        mmc->max_req_size = mmc->max_blk_count * mmc->max_blk_size;
1164        mmc->max_seg_size = mmc->max_req_size;
1165
1166        /*
1167         * At the moment, we don't know how to reliably enable HS400.
1168         * From the different datasheets, it is not even clear if this mode
1169         * is officially supported by any of the SoCs
1170         */
1171        mmc->caps2 &= ~MMC_CAP2_HS400;
1172
1173        if (host->dram_access_quirk) {
1174                /*
1175                 * The MMC Controller embeds 1,5KiB of internal SRAM
1176                 * that can be used to be used as bounce buffer.
1177                 * In the case of the G12A SDIO controller, use these
1178                 * instead of the DDR memory
1179                 */
1180                host->bounce_buf_size = SD_EMMC_SRAM_DATA_BUF_LEN;
1181                host->bounce_buf = host->regs + SD_EMMC_SRAM_DATA_BUF_OFF;
1182                host->bounce_dma_addr = res->start + SD_EMMC_SRAM_DATA_BUF_OFF;
1183        } else {
1184                /* data bounce buffer */
1185                host->bounce_buf_size = mmc->max_req_size;
1186                host->bounce_buf =
1187                        dma_alloc_coherent(host->dev, host->bounce_buf_size,
1188                                           &host->bounce_dma_addr, GFP_KERNEL);
1189                if (host->bounce_buf == NULL) {
1190                        dev_err(host->dev, "Unable to map allocate DMA bounce buffer.\n");
1191                        ret = -ENOMEM;
1192                        goto err_free_irq;
1193                }
1194        }
1195
1196        host->descs = dma_alloc_coherent(host->dev, SD_EMMC_DESC_BUF_LEN,
1197                      &host->descs_dma_addr, GFP_KERNEL);
1198        if (!host->descs) {
1199                dev_err(host->dev, "Allocating descriptor DMA buffer failed\n");
1200                ret = -ENOMEM;
1201                goto err_bounce_buf;
1202        }
1203
1204        mmc->ops = &meson_mmc_ops;
1205        mmc_add_host(mmc);
1206
1207        return 0;
1208
1209err_bounce_buf:
1210        if (!host->dram_access_quirk)
1211                dma_free_coherent(host->dev, host->bounce_buf_size,
1212                                  host->bounce_buf, host->bounce_dma_addr);
1213err_free_irq:
1214        free_irq(host->irq, host);
1215err_init_clk:
1216        clk_disable_unprepare(host->mmc_clk);
1217err_core_clk:
1218        clk_disable_unprepare(host->core_clk);
1219free_host:
1220        mmc_free_host(mmc);
1221        return ret;
1222}
1223
1224static int meson_mmc_remove(struct platform_device *pdev)
1225{
1226        struct meson_host *host = dev_get_drvdata(&pdev->dev);
1227
1228        mmc_remove_host(host->mmc);
1229
1230        /* disable interrupts */
1231        writel(0, host->regs + SD_EMMC_IRQ_EN);
1232        free_irq(host->irq, host);
1233
1234        dma_free_coherent(host->dev, SD_EMMC_DESC_BUF_LEN,
1235                          host->descs, host->descs_dma_addr);
1236
1237        if (!host->dram_access_quirk)
1238                dma_free_coherent(host->dev, host->bounce_buf_size,
1239                                  host->bounce_buf, host->bounce_dma_addr);
1240
1241        clk_disable_unprepare(host->mmc_clk);
1242        clk_disable_unprepare(host->core_clk);
1243
1244        mmc_free_host(host->mmc);
1245        return 0;
1246}
1247
1248static const struct meson_mmc_data meson_gx_data = {
1249        .tx_delay_mask  = CLK_V2_TX_DELAY_MASK,
1250        .rx_delay_mask  = CLK_V2_RX_DELAY_MASK,
1251        .always_on      = CLK_V2_ALWAYS_ON,
1252        .adjust         = SD_EMMC_ADJUST,
1253};
1254
1255static const struct meson_mmc_data meson_axg_data = {
1256        .tx_delay_mask  = CLK_V3_TX_DELAY_MASK,
1257        .rx_delay_mask  = CLK_V3_RX_DELAY_MASK,
1258        .always_on      = CLK_V3_ALWAYS_ON,
1259        .adjust         = SD_EMMC_V3_ADJUST,
1260};
1261
1262static const struct of_device_id meson_mmc_of_match[] = {
1263        { .compatible = "amlogic,meson-gx-mmc",         .data = &meson_gx_data },
1264        { .compatible = "amlogic,meson-gxbb-mmc",       .data = &meson_gx_data },
1265        { .compatible = "amlogic,meson-gxl-mmc",        .data = &meson_gx_data },
1266        { .compatible = "amlogic,meson-gxm-mmc",        .data = &meson_gx_data },
1267        { .compatible = "amlogic,meson-axg-mmc",        .data = &meson_axg_data },
1268        {}
1269};
1270MODULE_DEVICE_TABLE(of, meson_mmc_of_match);
1271
1272static struct platform_driver meson_mmc_driver = {
1273        .probe          = meson_mmc_probe,
1274        .remove         = meson_mmc_remove,
1275        .driver         = {
1276                .name = DRIVER_NAME,
1277                .of_match_table = of_match_ptr(meson_mmc_of_match),
1278        },
1279};
1280
1281module_platform_driver(meson_mmc_driver);
1282
1283MODULE_DESCRIPTION("Amlogic S905*/GX*/AXG SD/eMMC driver");
1284MODULE_AUTHOR("Kevin Hilman <khilman@baylibre.com>");
1285MODULE_LICENSE("GPL v2");
1286