// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * phy-ti-pipe3 - PIPE3 PHY driver.
 *
 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
 * Author: Kishon Vijay Abraham I <kishon@ti.com>
 */

#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <linux/phy/phy.h>
#include <linux/of.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/pm_runtime.h>
#include <linux/delay.h>
#include <linux/phy/omap_control_phy.h>
#include <linux/of_platform.h>
#include <linux/mfd/syscon.h>
#include <linux/regmap.h>

#define PLL_STATUS              0x00000004
#define PLL_GO                  0x00000008
#define PLL_CONFIGURATION1      0x0000000C
#define PLL_CONFIGURATION2      0x00000010
#define PLL_CONFIGURATION3      0x00000014
#define PLL_CONFIGURATION4      0x00000020

#define PLL_REGM_MASK           0x001FFE00
#define PLL_REGM_SHIFT          0x9
#define PLL_REGM_F_MASK         0x0003FFFF
#define PLL_REGM_F_SHIFT        0x0
#define PLL_REGN_MASK           0x000001FE
#define PLL_REGN_SHIFT          0x1
#define PLL_SELFREQDCO_MASK     0x0000000E
#define PLL_SELFREQDCO_SHIFT    0x1
#define PLL_SD_MASK             0x0003FC00
#define PLL_SD_SHIFT            10
#define SET_PLL_GO              0x1
#define PLL_LDOPWDN             BIT(15)
#define PLL_TICOPWDN            BIT(16)
#define PLL_LOCK                0x2
#define PLL_IDLE                0x1

#define SATA_PLL_SOFT_RESET     BIT(18)

#define PIPE3_PHY_PWRCTL_CLK_CMD_MASK   GENMASK(21, 14)
#define PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT  14

#define PIPE3_PHY_PWRCTL_CLK_FREQ_MASK  GENMASK(31, 22)
#define PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT 22

#define PIPE3_PHY_RX_POWERON       (0x1 << PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT)
#define PIPE3_PHY_TX_POWERON       (0x2 << PIPE3_PHY_PWRCTL_CLK_CMD_SHIFT)

#define PCIE_PCS_MASK                   0xFF0000
#define PCIE_PCS_DELAY_COUNT_SHIFT      0x10

#define PIPE3_PHY_RX_ANA_PROGRAMMABILITY        0x0000000C
#define INTERFACE_MASK                  GENMASK(31, 27)
#define INTERFACE_SHIFT                 27
#define INTERFACE_MODE_USBSS            BIT(4)
#define INTERFACE_MODE_SATA_1P5         BIT(3)
#define INTERFACE_MODE_SATA_3P0         BIT(2)
#define INTERFACE_MODE_PCIE             BIT(0)

#define LOSD_MASK                       GENMASK(17, 14)
#define LOSD_SHIFT                      14
#define MEM_PLLDIV                      GENMASK(6, 5)

#define PIPE3_PHY_RX_TRIM               0x0000001C
#define MEM_DLL_TRIM_SEL_MASK           GENMASK(31, 30)
#define MEM_DLL_TRIM_SHIFT              30

#define PIPE3_PHY_RX_DLL                0x00000024
#define MEM_DLL_PHINT_RATE_MASK         GENMASK(31, 30)
#define MEM_DLL_PHINT_RATE_SHIFT        30

#define PIPE3_PHY_RX_DIGITAL_MODES              0x00000028
#define MEM_HS_RATE_MASK                GENMASK(28, 27)
#define MEM_HS_RATE_SHIFT               27
#define MEM_OVRD_HS_RATE                BIT(26)
#define MEM_OVRD_HS_RATE_SHIFT          26
#define MEM_CDR_FASTLOCK                BIT(23)
#define MEM_CDR_FASTLOCK_SHIFT          23
#define MEM_CDR_LBW_MASK                GENMASK(22, 21)
#define MEM_CDR_LBW_SHIFT               21
#define MEM_CDR_STEPCNT_MASK            GENMASK(20, 19)
#define MEM_CDR_STEPCNT_SHIFT           19
#define MEM_CDR_STL_MASK                GENMASK(18, 16)
#define MEM_CDR_STL_SHIFT               16
#define MEM_CDR_THR_MASK                GENMASK(15, 13)
#define MEM_CDR_THR_SHIFT               13
#define MEM_CDR_THR_MODE                BIT(12)
#define MEM_CDR_THR_MODE_SHIFT          12
#define MEM_CDR_2NDO_SDM_MODE           BIT(11)
#define MEM_CDR_2NDO_SDM_MODE_SHIFT     11

#define PIPE3_PHY_RX_EQUALIZER          0x00000038
#define MEM_EQLEV_MASK                  GENMASK(31, 16)
#define MEM_EQLEV_SHIFT                 16
#define MEM_EQFTC_MASK                  GENMASK(15, 11)
#define MEM_EQFTC_SHIFT                 11
#define MEM_EQCTL_MASK                  GENMASK(10, 7)
#define MEM_EQCTL_SHIFT                 7
#define MEM_OVRD_EQLEV                  BIT(2)
#define MEM_OVRD_EQLEV_SHIFT            2
#define MEM_OVRD_EQFTC                  BIT(1)
#define MEM_OVRD_EQFTC_SHIFT            1

#define SATA_PHY_RX_IO_AND_A2D_OVERRIDES        0x44
#define MEM_CDR_LOS_SOURCE_MASK         GENMASK(10, 9)
#define MEM_CDR_LOS_SOURCE_SHIFT        9

/*
 * This is an Empirical value that works, need to confirm the actual
 * value required for the PIPE3PHY_PLL_CONFIGURATION2.PLL_IDLE status
 * to be correctly reflected in the PIPE3PHY_PLL_STATUS register.
 */
#define PLL_IDLE_TIME   100     /* in milliseconds */
#define PLL_LOCK_TIME   100     /* in milliseconds */

enum pipe3_mode { PIPE3_MODE_PCIE = 1,
                  PIPE3_MODE_SATA,
                  PIPE3_MODE_USBSS };

struct pipe3_dpll_params {
        u16     m;
        u8      n;
        u8      freq:3;
        u8      sd;
        u32     mf;
};

struct pipe3_dpll_map {
        unsigned long rate;
        struct pipe3_dpll_params params;
};

struct pipe3_settings {
        u8 ana_interface;
        u8 ana_losd;
        u8 dig_fastlock;
        u8 dig_lbw;
        u8 dig_stepcnt;
        u8 dig_stl;
        u8 dig_thr;
        u8 dig_thr_mode;
        u8 dig_2ndo_sdm_mode;
        u8 dig_hs_rate;
        u8 dig_ovrd_hs_rate;
        u8 dll_trim_sel;
        u8 dll_phint_rate;
        u8 eq_lev;
        u8 eq_ftc;
        u8 eq_ctl;
        u8 eq_ovrd_lev;
        u8 eq_ovrd_ftc;
};

struct ti_pipe3 {
        void __iomem            *pll_ctrl_base;
        void __iomem            *phy_rx;
        void __iomem            *phy_tx;
        struct device           *dev;
        struct device           *control_dev;
        struct clk              *wkupclk;
        struct clk              *sys_clk;
        struct clk              *refclk;
        struct clk              *div_clk;
        struct pipe3_dpll_map   *dpll_map;
        struct regmap           *phy_power_syscon; /* ctrl. reg. acces */
        struct regmap           *pcs_syscon; /* ctrl. reg. acces */
        struct regmap           *dpll_reset_syscon; /* ctrl. reg. acces */
        unsigned int            dpll_reset_reg; /* reg. index within syscon */
        unsigned int            power_reg; /* power reg. index within syscon */
        unsigned int            pcie_pcs_reg; /* pcs reg. index in syscon */
        bool                    sata_refclk_enabled;
        enum pipe3_mode         mode;
        struct pipe3_settings   settings;
};

static struct pipe3_dpll_map dpll_map_usb[] = {
        {12000000, {1250, 5, 4, 20, 0} },       /* 12 MHz */
        {16800000, {3125, 20, 4, 20, 0} },      /* 16.8 MHz */
        {19200000, {1172, 8, 4, 20, 65537} },   /* 19.2 MHz */
        {20000000, {1000, 7, 4, 10, 0} },       /* 20 MHz */
        {26000000, {1250, 12, 4, 20, 0} },      /* 26 MHz */
        {38400000, {3125, 47, 4, 20, 92843} },  /* 38.4 MHz */
        { },                                    /* Terminator */
};

static struct pipe3_dpll_map dpll_map_sata[] = {
        {12000000, {625, 4, 4, 6, 0} }, /* 12 MHz */
        {16800000, {625, 6, 4, 7, 0} },         /* 16.8 MHz */
        {19200000, {625, 7, 4, 6, 0} },         /* 19.2 MHz */
        {20000000, {750, 9, 4, 6, 0} },         /* 20 MHz */
        {26000000, {750, 12, 4, 6, 0} },        /* 26 MHz */
        {38400000, {625, 15, 4, 6, 0} },        /* 38.4 MHz */
        { },                                    /* Terminator */
};

struct pipe3_data {
        enum pipe3_mode mode;
        struct pipe3_dpll_map *dpll_map;
        struct pipe3_settings settings;
};

static struct pipe3_data data_usb = {
        .mode = PIPE3_MODE_USBSS,
        .dpll_map = dpll_map_usb,
        .settings = {
        /* DRA75x TRM Table 26-17 Preferred USB3_PHY_RX SCP Register Settings */
                .ana_interface = INTERFACE_MODE_USBSS,
                .ana_losd = 0xa,
                .dig_fastlock = 1,
                .dig_lbw = 3,
                .dig_stepcnt = 0,
                .dig_stl = 0x3,
                .dig_thr = 1,
                .dig_thr_mode = 1,
                .dig_2ndo_sdm_mode = 0,
                .dig_hs_rate = 0,
                .dig_ovrd_hs_rate = 1,
                .dll_trim_sel = 0x2,
                .dll_phint_rate = 0x3,
                .eq_lev = 0,
                .eq_ftc = 0,
                .eq_ctl = 0x9,
                .eq_ovrd_lev = 0,
                .eq_ovrd_ftc = 0,
        },
};

static struct pipe3_data data_sata = {
        .mode = PIPE3_MODE_SATA,
        .dpll_map = dpll_map_sata,
        .settings = {
        /* DRA75x TRM Table 26-9 Preferred SATA_PHY_RX SCP Register Settings */
                .ana_interface = INTERFACE_MODE_SATA_3P0,
                .ana_losd = 0x5,
                .dig_fastlock = 1,
                .dig_lbw = 3,
                .dig_stepcnt = 0,
                .dig_stl = 0x3,
                .dig_thr = 1,
                .dig_thr_mode = 1,
                .dig_2ndo_sdm_mode = 0,
                .dig_hs_rate = 0,       /* Not in TRM preferred settings */
                .dig_ovrd_hs_rate = 0,  /* Not in TRM preferred settings */
                .dll_trim_sel = 0x1,
                .dll_phint_rate = 0x2,  /* for 1.5 GHz DPLL clock */
                .eq_lev = 0,
                .eq_ftc = 0x1f,
                .eq_ctl = 0,
                .eq_ovrd_lev = 1,
                .eq_ovrd_ftc = 1,
        },
};

static struct pipe3_data data_pcie = {
        .mode = PIPE3_MODE_PCIE,
        .settings = {
        /* DRA75x TRM Table 26-62 Preferred PCIe_PHY_RX SCP Register Settings */
                .ana_interface = INTERFACE_MODE_PCIE,
                .ana_losd = 0xa,
                .dig_fastlock = 1,
                .dig_lbw = 3,
                .dig_stepcnt = 0,
                .dig_stl = 0x3,
                .dig_thr = 1,
                .dig_thr_mode = 1,
                .dig_2ndo_sdm_mode = 0,
                .dig_hs_rate = 0,
                .dig_ovrd_hs_rate = 0,
                .dll_trim_sel = 0x2,
                .dll_phint_rate = 0x3,
                .eq_lev = 0,
                .eq_ftc = 0x1f,
                .eq_ctl = 1,
                .eq_ovrd_lev = 0,
                .eq_ovrd_ftc = 0,
        },
};

static inline u32 ti_pipe3_readl(void __iomem *addr, unsigned offset)
{
        return __raw_readl(addr + offset);
}

static inline void ti_pipe3_writel(void __iomem *addr, unsigned offset,
        u32 data)
{
        __raw_writel(data, addr + offset);
}

static struct pipe3_dpll_params *ti_pipe3_get_dpll_params(struct ti_pipe3 *phy)
{
        unsigned long rate;
        struct pipe3_dpll_map *dpll_map = phy->dpll_map;

        rate = clk_get_rate(phy->sys_clk);

        for (; dpll_map->rate; dpll_map++) {
                if (rate == dpll_map->rate)
                        return &dpll_map->params;
        }

        dev_err(phy->dev, "No DPLL configuration for %lu Hz SYS CLK\n", rate);

        return NULL;
}

static int ti_pipe3_enable_clocks(struct ti_pipe3 *phy);
static void ti_pipe3_disable_clocks(struct ti_pipe3 *phy);

static int ti_pipe3_power_off(struct phy *x)
{
        int ret;
        struct ti_pipe3 *phy = phy_get_drvdata(x);

        if (!phy->phy_power_syscon) {
                omap_control_phy_power(phy->control_dev, 0);
                return 0;
        }

        ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
                                 PIPE3_PHY_PWRCTL_CLK_CMD_MASK, 0);
        return ret;
}

static void ti_pipe3_calibrate(struct ti_pipe3 *phy);

static int ti_pipe3_power_on(struct phy *x)
{
        u32 val;
        u32 mask;
        int ret;
        unsigned long rate;
        struct ti_pipe3 *phy = phy_get_drvdata(x);
        bool rx_pending = false;

        if (!phy->phy_power_syscon) {
                omap_control_phy_power(phy->control_dev, 1);
                return 0;
        }

        rate = clk_get_rate(phy->sys_clk);
        if (!rate) {
                dev_err(phy->dev, "Invalid clock rate\n");
                return -EINVAL;
        }
        rate = rate / 1000000;
        mask = OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_MASK;
        val = rate << OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_FREQ_SHIFT;
        ret = regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
                                 mask, val);
        /*
         * For PCIe, TX and RX must be powered on simultaneously.
         * For USB and SATA, TX must be powered on before RX
         */
        mask = OMAP_CTRL_PIPE3_PHY_PWRCTL_CLK_CMD_MASK;
        if (phy->mode == PIPE3_MODE_SATA || phy->mode == PIPE3_MODE_USBSS) {
                val = PIPE3_PHY_TX_POWERON;
                rx_pending = true;
        } else {
                val = PIPE3_PHY_TX_POWERON | PIPE3_PHY_RX_POWERON;
        }

        regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
                           mask, val);

        if (rx_pending) {
                val = PIPE3_PHY_TX_POWERON | PIPE3_PHY_RX_POWERON;
                regmap_update_bits(phy->phy_power_syscon, phy->power_reg,
                                   mask, val);
        }

        if (phy->mode == PIPE3_MODE_PCIE)
                ti_pipe3_calibrate(phy);

        return 0;
}

static int ti_pipe3_dpll_wait_lock(struct ti_pipe3 *phy)
{
        u32             val;
        unsigned long   timeout;

        timeout = jiffies + msecs_to_jiffies(PLL_LOCK_TIME);
        do {
                cpu_relax();
                val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_STATUS);
                if (val & PLL_LOCK)
                        return 0;
        } while (!time_after(jiffies, timeout));

        dev_err(phy->dev, "DPLL failed to lock\n");
        return -EBUSY;
}

static int ti_pipe3_dpll_program(struct ti_pipe3 *phy)
{
        u32                     val;
        struct pipe3_dpll_params *dpll_params;

        dpll_params = ti_pipe3_get_dpll_params(phy);
        if (!dpll_params)
                return -EINVAL;

        val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
        val &= ~PLL_REGN_MASK;
        val |= dpll_params->n << PLL_REGN_SHIFT;
        ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);

        val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
        val &= ~PLL_SELFREQDCO_MASK;
        val |= dpll_params->freq << PLL_SELFREQDCO_SHIFT;
        ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);

        val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
        val &= ~PLL_REGM_MASK;
        val |= dpll_params->m << PLL_REGM_SHIFT;
        ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);

        val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION4);
        val &= ~PLL_REGM_F_MASK;
        val |= dpll_params->mf << PLL_REGM_F_SHIFT;
        ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION4, val);

        val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION3);
        val &= ~PLL_SD_MASK;
        val |= dpll_params->sd << PLL_SD_SHIFT;
        ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION3, val);

        ti_pipe3_writel(phy->pll_ctrl_base, PLL_GO, SET_PLL_GO);

        return ti_pipe3_dpll_wait_lock(phy);
}

static void ti_pipe3_calibrate(struct ti_pipe3 *phy)
{
        u32 val;
        struct pipe3_settings *s = &phy->settings;

        val = ti_pipe3_readl(phy->phy_rx, PIPE3_PHY_RX_ANA_PROGRAMMABILITY);
        val &= ~(INTERFACE_MASK | LOSD_MASK | MEM_PLLDIV);
        val |= (s->ana_interface << INTERFACE_SHIFT | s->ana_losd << LOSD_SHIFT);
        ti_pipe3_writel(phy->phy_rx, PIPE3_PHY_RX_ANA_PROGRAMMABILITY, val);

        val = ti_pipe3_readl(phy->phy_rx, PIPE3_PHY_RX_DIGITAL_MODES);
        val &= ~(MEM_HS_RATE_MASK | MEM_OVRD_HS_RATE | MEM_CDR_FASTLOCK |
                 MEM_CDR_LBW_MASK | MEM_CDR_STEPCNT_MASK | MEM_CDR_STL_MASK |
                 MEM_CDR_THR_MASK | MEM_CDR_THR_MODE | MEM_CDR_2NDO_SDM_MODE);
        val |= s->dig_hs_rate << MEM_HS_RATE_SHIFT |
                s->dig_ovrd_hs_rate << MEM_OVRD_HS_RATE_SHIFT |
                s->dig_fastlock << MEM_CDR_FASTLOCK_SHIFT |
                s->dig_lbw << MEM_CDR_LBW_SHIFT |
                s->dig_stepcnt << MEM_CDR_STEPCNT_SHIFT |
                s->dig_stl << MEM_CDR_STL_SHIFT |
                s->dig_thr << MEM_CDR_THR_SHIFT |
                s->dig_thr_mode << MEM_CDR_THR_MODE_SHIFT |
                s->dig_2ndo_sdm_mode << MEM_CDR_2NDO_SDM_MODE_SHIFT;
        ti_pipe3_writel(phy->phy_rx, PIPE3_PHY_RX_DIGITAL_MODES, val);

        val = ti_pipe3_readl(phy->phy_rx, PIPE3_PHY_RX_TRIM);
        val &= ~MEM_DLL_TRIM_SEL_MASK;
        val |= s->dll_trim_sel << MEM_DLL_TRIM_SHIFT;
        ti_pipe3_writel(phy->phy_rx, PIPE3_PHY_RX_TRIM, val);

        val = ti_pipe3_readl(phy->phy_rx, PIPE3_PHY_RX_DLL);
        val &= ~MEM_DLL_PHINT_RATE_MASK;
        val |= s->dll_phint_rate << MEM_DLL_PHINT_RATE_SHIFT;
        ti_pipe3_writel(phy->phy_rx, PIPE3_PHY_RX_DLL, val);

        val = ti_pipe3_readl(phy->phy_rx, PIPE3_PHY_RX_EQUALIZER);
        val &= ~(MEM_EQLEV_MASK | MEM_EQFTC_MASK | MEM_EQCTL_MASK |
                 MEM_OVRD_EQLEV | MEM_OVRD_EQFTC);
        val |= s->eq_lev << MEM_EQLEV_SHIFT |
                s->eq_ftc << MEM_EQFTC_SHIFT |
                s->eq_ctl << MEM_EQCTL_SHIFT |
                s->eq_ovrd_lev << MEM_OVRD_EQLEV_SHIFT |
                s->eq_ovrd_ftc << MEM_OVRD_EQFTC_SHIFT;
        ti_pipe3_writel(phy->phy_rx, PIPE3_PHY_RX_EQUALIZER, val);

        if (phy->mode == PIPE3_MODE_SATA) {
                val = ti_pipe3_readl(phy->phy_rx,
                                     SATA_PHY_RX_IO_AND_A2D_OVERRIDES);
                val &= ~MEM_CDR_LOS_SOURCE_MASK;
                ti_pipe3_writel(phy->phy_rx, SATA_PHY_RX_IO_AND_A2D_OVERRIDES,
                                val);
        }
}

static int ti_pipe3_init(struct phy *x)
{
        struct ti_pipe3 *phy = phy_get_drvdata(x);
        u32 val;
        int ret = 0;

        ti_pipe3_enable_clocks(phy);
        /*
         * Set pcie_pcs register to 0x96 for proper functioning of phy
         * as recommended in AM572x TRM SPRUHZ6, section 18.5.2.2, table
         * 18-1804.
         */
        if (phy->mode == PIPE3_MODE_PCIE) {
                if (!phy->pcs_syscon) {
                        omap_control_pcie_pcs(phy->control_dev, 0x96);
                        return 0;
                }

                val = 0x96 << OMAP_CTRL_PCIE_PCS_DELAY_COUNT_SHIFT;
                ret = regmap_update_bits(phy->pcs_syscon, phy->pcie_pcs_reg,
                                         PCIE_PCS_MASK, val);
                return ret;
        }

        /* Bring it out of IDLE if it is IDLE */
        val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
        if (val & PLL_IDLE) {
                val &= ~PLL_IDLE;
                ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);
                ret = ti_pipe3_dpll_wait_lock(phy);
        }

        /* SATA has issues if re-programmed when locked */
        val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_STATUS);
        if ((val & PLL_LOCK) && phy->mode == PIPE3_MODE_SATA)
                return ret;

        /* Program the DPLL */
        ret = ti_pipe3_dpll_program(phy);
        if (ret) {
                ti_pipe3_disable_clocks(phy);
                return -EINVAL;
        }

        ti_pipe3_calibrate(phy);

        return ret;
}

static int ti_pipe3_exit(struct phy *x)
{
        struct ti_pipe3 *phy = phy_get_drvdata(x);
        u32 val;
        unsigned long timeout;

        /* If dpll_reset_syscon is not present we wont power down SATA DPLL
         * due to Errata i783
         */
        if (phy->mode == PIPE3_MODE_SATA && !phy->dpll_reset_syscon)
                return 0;

        /* PCIe doesn't have internal DPLL */
        if (phy->mode != PIPE3_MODE_PCIE) {
                /* Put DPLL in IDLE mode */
                val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
                val |= PLL_IDLE;
                ti_pipe3_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);

                /* wait for LDO and Oscillator to power down */
                timeout = jiffies + msecs_to_jiffies(PLL_IDLE_TIME);
                do {
                        cpu_relax();
                        val = ti_pipe3_readl(phy->pll_ctrl_base, PLL_STATUS);
                        if ((val & PLL_TICOPWDN) && (val & PLL_LDOPWDN))
                                break;
                } while (!time_after(jiffies, timeout));

                if (!(val & PLL_TICOPWDN) || !(val & PLL_LDOPWDN)) {
                        dev_err(phy->dev, "Failed to power down: PLL_STATUS 0x%x\n",
                                val);
                        return -EBUSY;
                }
        }

        /* i783: SATA needs control bit toggle after PLL unlock */
        if (phy->mode == PIPE3_MODE_SATA) {
                regmap_update_bits(phy->dpll_reset_syscon, phy->dpll_reset_reg,
                                   SATA_PLL_SOFT_RESET, SATA_PLL_SOFT_RESET);
                regmap_update_bits(phy->dpll_reset_syscon, phy->dpll_reset_reg,
                                   SATA_PLL_SOFT_RESET, 0);
        }

        ti_pipe3_disable_clocks(phy);

        return 0;
}
static const struct phy_ops ops = {
        .init           = ti_pipe3_init,
        .exit           = ti_pipe3_exit,
        .power_on       = ti_pipe3_power_on,
        .power_off      = ti_pipe3_power_off,
        .owner          = THIS_MODULE,
};

static const struct of_device_id ti_pipe3_id_table[];

static int ti_pipe3_get_clk(struct ti_pipe3 *phy)
{
        struct clk *clk;
        struct device *dev = phy->dev;

        phy->refclk = devm_clk_get(dev, "refclk");
        if (IS_ERR(phy->refclk)) {
                dev_err(dev, "unable to get refclk\n");
                /* older DTBs have missing refclk in SATA PHY
                 * so don't bail out in case of SATA PHY.
                 */
                if (phy->mode != PIPE3_MODE_SATA)
                        return PTR_ERR(phy->refclk);
        }

        if (phy->mode != PIPE3_MODE_SATA) {
                phy->wkupclk = devm_clk_get(dev, "wkupclk");
                if (IS_ERR(phy->wkupclk)) {
                        dev_err(dev, "unable to get wkupclk\n");
                        return PTR_ERR(phy->wkupclk);
                }
        } else {
                phy->wkupclk = ERR_PTR(-ENODEV);
        }

        if (phy->mode != PIPE3_MODE_PCIE || phy->phy_power_syscon) {
                phy->sys_clk = devm_clk_get(dev, "sysclk");
                if (IS_ERR(phy->sys_clk)) {
                        dev_err(dev, "unable to get sysclk\n");
                        return -EINVAL;
                }
        }

        if (phy->mode == PIPE3_MODE_PCIE) {
                clk = devm_clk_get(dev, "dpll_ref");
                if (IS_ERR(clk)) {
                        dev_err(dev, "unable to get dpll ref clk\n");
                        return PTR_ERR(clk);
                }
                clk_set_rate(clk, 1500000000);

                clk = devm_clk_get(dev, "dpll_ref_m2");
                if (IS_ERR(clk)) {
                        dev_err(dev, "unable to get dpll ref m2 clk\n");
                        return PTR_ERR(clk);
                }
                clk_set_rate(clk, 100000000);

                clk = devm_clk_get(dev, "phy-div");
                if (IS_ERR(clk)) {
                        dev_err(dev, "unable to get phy-div clk\n");
                        return PTR_ERR(clk);
                }
                clk_set_rate(clk, 100000000);

                phy->div_clk = devm_clk_get(dev, "div-clk");
                if (IS_ERR(phy->div_clk)) {
                        dev_err(dev, "unable to get div-clk\n");
                        return PTR_ERR(phy->div_clk);
                }
        } else {
                phy->div_clk = ERR_PTR(-ENODEV);
        }

        return 0;
}

static int ti_pipe3_get_sysctrl(struct ti_pipe3 *phy)
{
        struct device *dev = phy->dev;
        struct device_node *node = dev->of_node;
        struct device_node *control_node;
        struct platform_device *control_pdev;

        phy->phy_power_syscon = syscon_regmap_lookup_by_phandle(node,
                                                        "syscon-phy-power");
        if (IS_ERR(phy->phy_power_syscon)) {
                dev_dbg(dev,
                        "can't get syscon-phy-power, using control device\n");
                phy->phy_power_syscon = NULL;
        } else {
                if (of_property_read_u32_index(node,
                                               "syscon-phy-power", 1,
                                               &phy->power_reg)) {
                        dev_err(dev, "couldn't get power reg. offset\n");
                        return -EINVAL;
                }
        }

        if (!phy->phy_power_syscon) {
                control_node = of_parse_phandle(node, "ctrl-module", 0);
                if (!control_node) {
                        dev_err(dev, "Failed to get control device phandle\n");
                        return -EINVAL;
                }

                control_pdev = of_find_device_by_node(control_node);
                if (!control_pdev) {
                        dev_err(dev, "Failed to get control device\n");
                        return -EINVAL;
                }

                phy->control_dev = &control_pdev->dev;
        }

        if (phy->mode == PIPE3_MODE_PCIE) {
                phy->pcs_syscon = syscon_regmap_lookup_by_phandle(node,
                                                                  "syscon-pcs");
                if (IS_ERR(phy->pcs_syscon)) {
                        dev_dbg(dev,
                                "can't get syscon-pcs, using omap control\n");
                        phy->pcs_syscon = NULL;
                } else {
                        if (of_property_read_u32_index(node,
                                                       "syscon-pcs", 1,
                                                       &phy->pcie_pcs_reg)) {
                                dev_err(dev,
                                        "couldn't get pcie pcs reg. offset\n");
                                return -EINVAL;
                        }
                }
        }

        if (phy->mode == PIPE3_MODE_SATA) {
                phy->dpll_reset_syscon = syscon_regmap_lookup_by_phandle(node,
                                                        "syscon-pllreset");
                if (IS_ERR(phy->dpll_reset_syscon)) {
                        dev_info(dev,
                                 "can't get syscon-pllreset, sata dpll won't idle\n");
                        phy->dpll_reset_syscon = NULL;
                } else {
                        if (of_property_read_u32_index(node,
                                                       "syscon-pllreset", 1,
                                                       &phy->dpll_reset_reg)) {
                                dev_err(dev,
                                        "couldn't get pllreset reg. offset\n");
                                return -EINVAL;
                        }
                }
        }

        return 0;
}

static int ti_pipe3_get_tx_rx_base(struct ti_pipe3 *phy)
{
        struct resource *res;
        struct device *dev = phy->dev;
        struct platform_device *pdev = to_platform_device(dev);

        res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
                                           "phy_rx");
        phy->phy_rx = devm_ioremap_resource(dev, res);
        if (IS_ERR(phy->phy_rx))
                return PTR_ERR(phy->phy_rx);

        res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
                                           "phy_tx");
        phy->phy_tx = devm_ioremap_resource(dev, res);

        return PTR_ERR_OR_ZERO(phy->phy_tx);
}

static int ti_pipe3_get_pll_base(struct ti_pipe3 *phy)
{
        struct resource *res;
        struct device *dev = phy->dev;
        struct platform_device *pdev = to_platform_device(dev);

        if (phy->mode == PIPE3_MODE_PCIE)
                return 0;

        res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
                                           "pll_ctrl");
        phy->pll_ctrl_base = devm_ioremap_resource(dev, res);
        return PTR_ERR_OR_ZERO(phy->pll_ctrl_base);
}

static int ti_pipe3_probe(struct platform_device *pdev)
{
        struct ti_pipe3 *phy;
        struct phy *generic_phy;
        struct phy_provider *phy_provider;
        struct device *dev = &pdev->dev;
        int ret;
        const struct of_device_id *match;
        struct pipe3_data *data;

        phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
        if (!phy)
                return -ENOMEM;

        match = of_match_device(ti_pipe3_id_table, dev);
        if (!match)
                return -EINVAL;

        data = (struct pipe3_data *)match->data;
        if (!data) {
                dev_err(dev, "no driver data\n");
                return -EINVAL;
        }

        phy->dev = dev;
        phy->mode = data->mode;
        phy->dpll_map = data->dpll_map;
        phy->settings = data->settings;

        ret = ti_pipe3_get_pll_base(phy);
        if (ret)
                return ret;

        ret = ti_pipe3_get_tx_rx_base(phy);
        if (ret)
                return ret;

        ret = ti_pipe3_get_sysctrl(phy);
        if (ret)
                return ret;

        ret = ti_pipe3_get_clk(phy);
        if (ret)
                return ret;

        platform_set_drvdata(pdev, phy);
        pm_runtime_enable(dev);

        /*
         * Prevent auto-disable of refclk for SATA PHY due to Errata i783
         */
        if (phy->mode == PIPE3_MODE_SATA) {
                if (!IS_ERR(phy->refclk)) {
                        clk_prepare_enable(phy->refclk);
                        phy->sata_refclk_enabled = true;
                }
        }

        generic_phy = devm_phy_create(dev, NULL, &ops);
        if (IS_ERR(generic_phy))
                return PTR_ERR(generic_phy);

        phy_set_drvdata(generic_phy, phy);

        ti_pipe3_power_off(generic_phy);

        phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
        return PTR_ERR_OR_ZERO(phy_provider);
}

static int ti_pipe3_remove(struct platform_device *pdev)
{
        pm_runtime_disable(&pdev->dev);

        return 0;
}

static int ti_pipe3_enable_clocks(struct ti_pipe3 *phy)
{
        int ret = 0;

        if (!IS_ERR(phy->refclk)) {
                ret = clk_prepare_enable(phy->refclk);
                if (ret) {
                        dev_err(phy->dev, "Failed to enable refclk %d\n", ret);
                        return ret;
                }
        }

        if (!IS_ERR(phy->wkupclk)) {
                ret = clk_prepare_enable(phy->wkupclk);
                if (ret) {
                        dev_err(phy->dev, "Failed to enable wkupclk %d\n", ret);
                        goto disable_refclk;
                }
        }

        if (!IS_ERR(phy->div_clk)) {
                ret = clk_prepare_enable(phy->div_clk);
                if (ret) {
                        dev_err(phy->dev, "Failed to enable div_clk %d\n", ret);
                        goto disable_wkupclk;
                }
        }

        return 0;

disable_wkupclk:
        if (!IS_ERR(phy->wkupclk))
                clk_disable_unprepare(phy->wkupclk);

disable_refclk:
        if (!IS_ERR(phy->refclk))
                clk_disable_unprepare(phy->refclk);

        return ret;
}

static void ti_pipe3_disable_clocks(struct ti_pipe3 *phy)
{
        if (!IS_ERR(phy->wkupclk))
                clk_disable_unprepare(phy->wkupclk);
        if (!IS_ERR(phy->refclk)) {
                clk_disable_unprepare(phy->refclk);
                /*
                 * SATA refclk needs an additional disable as we left it
                 * on in probe to avoid Errata i783
                 */
                if (phy->sata_refclk_enabled) {
                        clk_disable_unprepare(phy->refclk);
                        phy->sata_refclk_enabled = false;
                }
        }

        if (!IS_ERR(phy->div_clk))
                clk_disable_unprepare(phy->div_clk);
}

static const struct of_device_id ti_pipe3_id_table[] = {
        {
                .compatible = "ti,phy-usb3",
                .data = &data_usb,
        },
        {
                .compatible = "ti,omap-usb3",
                .data = &data_usb,
        },
        {
                .compatible = "ti,phy-pipe3-sata",
                .data = &data_sata,
        },
        {
                .compatible = "ti,phy-pipe3-pcie",
                .data = &data_pcie,
        },
        {}
};
MODULE_DEVICE_TABLE(of, ti_pipe3_id_table);

static struct platform_driver ti_pipe3_driver = {
        .probe          = ti_pipe3_probe,
        .remove         = ti_pipe3_remove,
        .driver         = {
                .name   = "ti-pipe3",
                .of_match_table = ti_pipe3_id_table,
        },
};

module_platform_driver(ti_pipe3_driver);

MODULE_ALIAS("platform:ti_pipe3");
MODULE_AUTHOR("Texas Instruments Inc.");
MODULE_DESCRIPTION("TI PIPE3 phy driver");
MODULE_LICENSE("GPL v2");