1
2menu "Remoteproc drivers"
3
4config REMOTEPROC
5 tristate "Support for Remote Processor subsystem"
6 depends on HAS_DMA
7 select CRC32
8 select FW_LOADER
9 select VIRTIO
10 select WANT_DEV_COREDUMP
11 help
12 Support for remote processors (such as DSP coprocessors). These
13 are mainly used on embedded systems.
14
15if REMOTEPROC
16
17config IMX_REMOTEPROC
18 tristate "IMX6/7 remoteproc support"
19 depends on ARCH_MXC
20 help
21 Say y here to support iMX's remote processors (Cortex M4
22 on iMX7D) via the remote processor framework.
23
24 It's safe to say N here.
25
26config OMAP_REMOTEPROC
27 tristate "OMAP remoteproc support"
28 depends on ARCH_OMAP4 || SOC_OMAP5
29 depends on OMAP_IOMMU
30 select MAILBOX
31 select OMAP2PLUS_MBOX
32 help
33 Say y here to support OMAP's remote processors (dual M3
34 and DSP on OMAP4) via the remote processor framework.
35
36 Currently only supported on OMAP4.
37
38 Usually you want to say Y here, in order to enable multimedia
39 use-cases to run on your platform (multimedia codecs are
40 offloaded to remote DSP processors using this framework).
41
42 It's safe to say N here if you're not interested in multimedia
43 offloading or just want a bare minimum kernel.
44
45config WKUP_M3_RPROC
46 tristate "AMx3xx Wakeup M3 remoteproc support"
47 depends on SOC_AM33XX || SOC_AM43XX
48 help
49 Say y here to support Wakeup M3 remote processor on TI AM33xx
50 and AM43xx family of SoCs.
51
52 Required for Suspend-to-RAM on AM33xx and AM43xx SoCs. Also needed
53 for deep CPUIdle states on AM33xx SoCs. Allows for loading of the
54 firmware onto these remote processors.
55 If unsure say N.
56
57config DA8XX_REMOTEPROC
58 tristate "DA8xx/OMAP-L13x remoteproc support"
59 depends on ARCH_DAVINCI_DA8XX
60 depends on DMA_CMA
61 help
62 Say y here to support DA8xx/OMAP-L13x remote processors via the
63 remote processor framework.
64
65 You want to say y here in order to enable AMP
66 use-cases to run on your platform (multimedia codecs are
67 offloaded to remote DSP processors using this framework).
68
69 This module controls the name of the firmware file that gets
70 loaded on the DSP. This file must reside in the /lib/firmware
71 directory. It can be specified via the module parameter
72 da8xx_fw_name=<filename>, and if not specified will default to
73 "rproc-dsp-fw".
74
75 It's safe to say n here if you're not interested in multimedia
76 offloading.
77
78config KEYSTONE_REMOTEPROC
79 tristate "Keystone Remoteproc support"
80 depends on ARCH_KEYSTONE
81 help
82 Say Y here here to support Keystone remote processors (DSP)
83 via the remote processor framework.
84
85 It's safe to say N here if you're not interested in the Keystone
86 DSPs or just want to use a bare minimum kernel.
87
88config QCOM_RPROC_COMMON
89 tristate
90
91config QCOM_Q6V5_COMMON
92 tristate
93 depends on ARCH_QCOM
94 depends on QCOM_SMEM
95
96config QCOM_Q6V5_ADSP
97 tristate "Qualcomm Technology Inc ADSP Peripheral Image Loader"
98 depends on OF && ARCH_QCOM
99 depends on QCOM_SMEM
100 depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
101 depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
102 depends on QCOM_SYSMON || QCOM_SYSMON=n
103 select MFD_SYSCON
104 select QCOM_MDT_LOADER
105 select QCOM_Q6V5_COMMON
106 select QCOM_RPROC_COMMON
107 help
108 Say y here to support the Peripheral Image Loader
109 for the Qualcomm Technology Inc. ADSP remote processors.
110
111config QCOM_Q6V5_MSS
112 tristate "Qualcomm Hexagon V5 self-authenticating modem subsystem support"
113 depends on OF && ARCH_QCOM
114 depends on QCOM_SMEM
115 depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
116 depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
117 depends on QCOM_SYSMON || QCOM_SYSMON=n
118 select MFD_SYSCON
119 select QCOM_MDT_LOADER
120 select QCOM_Q6V5_COMMON
121 select QCOM_RPROC_COMMON
122 select QCOM_SCM
123 help
124 Say y here to support the Qualcomm self-authenticating modem
125 subsystem based on Hexagon V5.
126
127config QCOM_Q6V5_PAS
128 tristate "Qualcomm Hexagon v5 Peripheral Authentication Service support"
129 depends on OF && ARCH_QCOM
130 depends on QCOM_SMEM
131 depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
132 depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
133 depends on QCOM_SYSMON || QCOM_SYSMON=n
134 select MFD_SYSCON
135 select QCOM_MDT_LOADER
136 select QCOM_Q6V5_COMMON
137 select QCOM_RPROC_COMMON
138 select QCOM_SCM
139 help
140 Say y here to support the TrustZone based Peripherial Image Loader
141 for the Qualcomm Hexagon v5 based remote processors. This is commonly
142 used to control subsystems such as ADSP, Compute and Sensor.
143
144config QCOM_Q6V5_WCSS
145 tristate "Qualcomm Hexagon based WCSS Peripheral Image Loader"
146 depends on OF && ARCH_QCOM
147 depends on QCOM_SMEM
148 depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
149 depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
150 depends on QCOM_SYSMON || QCOM_SYSMON=n
151 select MFD_SYSCON
152 select QCOM_MDT_LOADER
153 select QCOM_Q6V5_COMMON
154 select QCOM_RPROC_COMMON
155 select QCOM_SCM
156 help
157 Say y here to support the Qualcomm Peripheral Image Loader for the
158 Hexagon V5 based WCSS remote processors.
159
160config QCOM_SYSMON
161 tristate "Qualcomm sysmon driver"
162 depends on RPMSG
163 depends on ARCH_QCOM
164 depends on NET
165 select QCOM_QMI_HELPERS
166 help
167 The sysmon driver implements a sysmon QMI client and a handler for
168 the sys_mon SMD and GLINK channel, which are used for graceful
169 shutdown, retrieving failure information and propagating information
170 about other subsystems being shut down.
171
172 Say y here if your system runs firmware on any other subsystems, e.g.
173 modem or DSP.
174
175config QCOM_WCNSS_PIL
176 tristate "Qualcomm WCNSS Peripheral Image Loader"
177 depends on OF && ARCH_QCOM
178 depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
179 depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
180 depends on QCOM_SMEM
181 depends on QCOM_SYSMON || QCOM_SYSMON=n
182 select QCOM_MDT_LOADER
183 select QCOM_RPROC_COMMON
184 select QCOM_SCM
185 help
186 Say y here to support the Peripheral Image Loader for the Qualcomm
187 Wireless Connectivity Subsystem.
188
189config ST_REMOTEPROC
190 tristate "ST remoteproc support"
191 depends on ARCH_STI
192 select MAILBOX
193 select STI_MBOX
194 help
195 Say y here to support ST's adjunct processors via the remote
196 processor framework.
197 This can be either built-in or a loadable module.
198
199config ST_SLIM_REMOTEPROC
200 tristate
201
202config STM32_RPROC
203 tristate "STM32 remoteproc support"
204 depends on ARCH_STM32
205 depends on REMOTEPROC
206 select MAILBOX
207 help
208 Say y here to support STM32 MCU processors via the
209 remote processor framework.
210
211 You want to say y here in order to enable AMP
212 use-cases to run on your platform (dedicated firmware could be
213 offloaded to remote MCU processors using this framework).
214
215 This can be either built-in or a loadable module.
216
217endif
218
219endmenu
220