1
2
3
4
5
6
7
8
9
10
11
12#include <linux/clk.h>
13#include <linux/io.h>
14#include <linux/module.h>
15#include <linux/of.h>
16#include <linux/platform_device.h>
17
18#include "8250.h"
19
20
21#define LPC18XX_UART_RS485CTRL (0x04c / sizeof(u32))
22#define LPC18XX_UART_RS485CTRL_NMMEN BIT(0)
23#define LPC18XX_UART_RS485CTRL_DCTRL BIT(4)
24#define LPC18XX_UART_RS485CTRL_OINV BIT(5)
25#define LPC18XX_UART_RS485DLY (0x054 / sizeof(u32))
26#define LPC18XX_UART_RS485DLY_MAX 255
27
28struct lpc18xx_uart_data {
29 struct uart_8250_dma dma;
30 struct clk *clk_uart;
31 struct clk *clk_reg;
32 int line;
33};
34
35static int lpc18xx_rs485_config(struct uart_port *port,
36 struct serial_rs485 *rs485)
37{
38 struct uart_8250_port *up = up_to_u8250p(port);
39 u32 rs485_ctrl_reg = 0;
40 u32 rs485_dly_reg = 0;
41 unsigned baud_clk;
42
43 if (rs485->flags & SER_RS485_ENABLED)
44 memset(rs485->padding, 0, sizeof(rs485->padding));
45 else
46 memset(rs485, 0, sizeof(*rs485));
47
48 rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
49 SER_RS485_RTS_AFTER_SEND;
50
51 if (rs485->flags & SER_RS485_ENABLED) {
52 rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_NMMEN |
53 LPC18XX_UART_RS485CTRL_DCTRL;
54
55 if (rs485->flags & SER_RS485_RTS_ON_SEND) {
56 rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_OINV;
57 rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
58 } else {
59 rs485->flags |= SER_RS485_RTS_AFTER_SEND;
60 }
61 }
62
63 if (rs485->delay_rts_after_send) {
64 baud_clk = port->uartclk / up->dl_read(up);
65 rs485_dly_reg = DIV_ROUND_UP(rs485->delay_rts_after_send
66 * baud_clk, MSEC_PER_SEC);
67
68 if (rs485_dly_reg > LPC18XX_UART_RS485DLY_MAX)
69 rs485_dly_reg = LPC18XX_UART_RS485DLY_MAX;
70
71
72 rs485->delay_rts_after_send = (rs485_dly_reg * MSEC_PER_SEC)
73 / baud_clk;
74 }
75
76
77 rs485->delay_rts_before_send = 0;
78
79 serial_out(up, LPC18XX_UART_RS485CTRL, rs485_ctrl_reg);
80 serial_out(up, LPC18XX_UART_RS485DLY, rs485_dly_reg);
81
82 port->rs485 = *rs485;
83
84 return 0;
85}
86
87static void lpc18xx_uart_serial_out(struct uart_port *p, int offset, int value)
88{
89
90
91
92
93
94 if (offset == UART_FCR && (value & UART_FCR_ENABLE_FIFO))
95 value |= UART_FCR_DMA_SELECT;
96
97 offset = offset << p->regshift;
98 writel(value, p->membase + offset);
99}
100
101static int lpc18xx_serial_probe(struct platform_device *pdev)
102{
103 struct lpc18xx_uart_data *data;
104 struct uart_8250_port uart;
105 struct resource *res;
106 int irq, ret;
107
108 irq = platform_get_irq(pdev, 0);
109 if (irq < 0) {
110 dev_err(&pdev->dev, "irq not found");
111 return irq;
112 }
113
114 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
115 if (!res) {
116 dev_err(&pdev->dev, "memory resource not found");
117 return -EINVAL;
118 }
119
120 memset(&uart, 0, sizeof(uart));
121
122 uart.port.membase = devm_ioremap(&pdev->dev, res->start,
123 resource_size(res));
124 if (!uart.port.membase)
125 return -ENOMEM;
126
127 data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
128 if (!data)
129 return -ENOMEM;
130
131 data->clk_uart = devm_clk_get(&pdev->dev, "uartclk");
132 if (IS_ERR(data->clk_uart)) {
133 dev_err(&pdev->dev, "uart clock not found\n");
134 return PTR_ERR(data->clk_uart);
135 }
136
137 data->clk_reg = devm_clk_get(&pdev->dev, "reg");
138 if (IS_ERR(data->clk_reg)) {
139 dev_err(&pdev->dev, "reg clock not found\n");
140 return PTR_ERR(data->clk_reg);
141 }
142
143 ret = clk_prepare_enable(data->clk_reg);
144 if (ret) {
145 dev_err(&pdev->dev, "unable to enable reg clock\n");
146 return ret;
147 }
148
149 ret = clk_prepare_enable(data->clk_uart);
150 if (ret) {
151 dev_err(&pdev->dev, "unable to enable uart clock\n");
152 goto dis_clk_reg;
153 }
154
155 ret = of_alias_get_id(pdev->dev.of_node, "serial");
156 if (ret >= 0)
157 uart.port.line = ret;
158
159 data->dma.rx_param = data;
160 data->dma.tx_param = data;
161
162 spin_lock_init(&uart.port.lock);
163 uart.port.dev = &pdev->dev;
164 uart.port.irq = irq;
165 uart.port.iotype = UPIO_MEM32;
166 uart.port.mapbase = res->start;
167 uart.port.regshift = 2;
168 uart.port.type = PORT_16550A;
169 uart.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_SKIP_TEST;
170 uart.port.uartclk = clk_get_rate(data->clk_uart);
171 uart.port.private_data = data;
172 uart.port.rs485_config = lpc18xx_rs485_config;
173 uart.port.serial_out = lpc18xx_uart_serial_out;
174
175 uart.dma = &data->dma;
176 uart.dma->rxconf.src_maxburst = 1;
177 uart.dma->txconf.dst_maxburst = 1;
178
179 ret = serial8250_register_8250_port(&uart);
180 if (ret < 0) {
181 dev_err(&pdev->dev, "unable to register 8250 port\n");
182 goto dis_uart_clk;
183 }
184
185 data->line = ret;
186 platform_set_drvdata(pdev, data);
187
188 return 0;
189
190dis_uart_clk:
191 clk_disable_unprepare(data->clk_uart);
192dis_clk_reg:
193 clk_disable_unprepare(data->clk_reg);
194 return ret;
195}
196
197static int lpc18xx_serial_remove(struct platform_device *pdev)
198{
199 struct lpc18xx_uart_data *data = platform_get_drvdata(pdev);
200
201 serial8250_unregister_port(data->line);
202 clk_disable_unprepare(data->clk_uart);
203 clk_disable_unprepare(data->clk_reg);
204
205 return 0;
206}
207
208static const struct of_device_id lpc18xx_serial_match[] = {
209 { .compatible = "nxp,lpc1850-uart" },
210 { },
211};
212MODULE_DEVICE_TABLE(of, lpc18xx_serial_match);
213
214static struct platform_driver lpc18xx_serial_driver = {
215 .probe = lpc18xx_serial_probe,
216 .remove = lpc18xx_serial_remove,
217 .driver = {
218 .name = "lpc18xx-uart",
219 .of_match_table = lpc18xx_serial_match,
220 },
221};
222module_platform_driver(lpc18xx_serial_driver);
223
224MODULE_AUTHOR("Joachim Eastwood <manabian@gmail.com>");
225MODULE_DESCRIPTION("Serial port driver NXP LPC18xx/43xx devices");
226MODULE_LICENSE("GPL v2");
227
