linux/drivers/usb/gadget/udc/fsl_usb2_udc.h
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0+
   2/*
   3 * Copyright (C) 2004,2012 Freescale Semiconductor, Inc
   4 * All rights reserved.
   5 *
   6 * Freescale USB device/endpoint management registers
   7 */
   8#ifndef __FSL_USB2_UDC_H
   9#define __FSL_USB2_UDC_H
  10
  11#include <linux/usb/ch9.h>
  12#include <linux/usb/gadget.h>
  13
  14/* ### define USB registers here
  15 */
  16#define USB_MAX_CTRL_PAYLOAD            64
  17#define USB_DR_SYS_OFFSET               0x400
  18
  19 /* USB DR device mode registers (Little Endian) */
  20struct usb_dr_device {
  21        /* Capability register */
  22        u8 res1[256];
  23        u16 caplength;          /* Capability Register Length */
  24        u16 hciversion;         /* Host Controller Interface Version */
  25        u32 hcsparams;          /* Host Controller Structural Parameters */
  26        u32 hccparams;          /* Host Controller Capability Parameters */
  27        u8 res2[20];
  28        u32 dciversion;         /* Device Controller Interface Version */
  29        u32 dccparams;          /* Device Controller Capability Parameters */
  30        u8 res3[24];
  31        /* Operation register */
  32        u32 usbcmd;             /* USB Command Register */
  33        u32 usbsts;             /* USB Status Register */
  34        u32 usbintr;            /* USB Interrupt Enable Register */
  35        u32 frindex;            /* Frame Index Register */
  36        u8 res4[4];
  37        u32 deviceaddr;         /* Device Address */
  38        u32 endpointlistaddr;   /* Endpoint List Address Register */
  39        u8 res5[4];
  40        u32 burstsize;          /* Master Interface Data Burst Size Register */
  41        u32 txttfilltuning;     /* Transmit FIFO Tuning Controls Register */
  42        u8 res6[24];
  43        u32 configflag;         /* Configure Flag Register */
  44        u32 portsc1;            /* Port 1 Status and Control Register */
  45        u8 res7[28];
  46        u32 otgsc;              /* On-The-Go Status and Control */
  47        u32 usbmode;            /* USB Mode Register */
  48        u32 endptsetupstat;     /* Endpoint Setup Status Register */
  49        u32 endpointprime;      /* Endpoint Initialization Register */
  50        u32 endptflush;         /* Endpoint Flush Register */
  51        u32 endptstatus;        /* Endpoint Status Register */
  52        u32 endptcomplete;      /* Endpoint Complete Register */
  53        u32 endptctrl[6];       /* Endpoint Control Registers */
  54};
  55
  56 /* USB DR host mode registers (Little Endian) */
  57struct usb_dr_host {
  58        /* Capability register */
  59        u8 res1[256];
  60        u16 caplength;          /* Capability Register Length */
  61        u16 hciversion;         /* Host Controller Interface Version */
  62        u32 hcsparams;          /* Host Controller Structural Parameters */
  63        u32 hccparams;          /* Host Controller Capability Parameters */
  64        u8 res2[20];
  65        u32 dciversion;         /* Device Controller Interface Version */
  66        u32 dccparams;          /* Device Controller Capability Parameters */
  67        u8 res3[24];
  68        /* Operation register */
  69        u32 usbcmd;             /* USB Command Register */
  70        u32 usbsts;             /* USB Status Register */
  71        u32 usbintr;            /* USB Interrupt Enable Register */
  72        u32 frindex;            /* Frame Index Register */
  73        u8 res4[4];
  74        u32 periodiclistbase;   /* Periodic Frame List Base Address Register */
  75        u32 asynclistaddr;      /* Current Asynchronous List Address Register */
  76        u8 res5[4];
  77        u32 burstsize;          /* Master Interface Data Burst Size Register */
  78        u32 txttfilltuning;     /* Transmit FIFO Tuning Controls Register */
  79        u8 res6[24];
  80        u32 configflag;         /* Configure Flag Register */
  81        u32 portsc1;            /* Port 1 Status and Control Register */
  82        u8 res7[28];
  83        u32 otgsc;              /* On-The-Go Status and Control */
  84        u32 usbmode;            /* USB Mode Register */
  85        u32 endptsetupstat;     /* Endpoint Setup Status Register */
  86        u32 endpointprime;      /* Endpoint Initialization Register */
  87        u32 endptflush;         /* Endpoint Flush Register */
  88        u32 endptstatus;        /* Endpoint Status Register */
  89        u32 endptcomplete;      /* Endpoint Complete Register */
  90        u32 endptctrl[6];       /* Endpoint Control Registers */
  91};
  92
  93 /* non-EHCI USB system interface registers (Big Endian) */
  94struct usb_sys_interface {
  95        u32 snoop1;
  96        u32 snoop2;
  97        u32 age_cnt_thresh;     /* Age Count Threshold Register */
  98        u32 pri_ctrl;           /* Priority Control Register */
  99        u32 si_ctrl;            /* System Interface Control Register */
 100        u8 res[236];
 101        u32 control;            /* General Purpose Control Register */
 102};
 103
 104/* ep0 transfer state */
 105#define WAIT_FOR_SETUP          0
 106#define DATA_STATE_XMIT         1
 107#define DATA_STATE_NEED_ZLP     2
 108#define WAIT_FOR_OUT_STATUS     3
 109#define DATA_STATE_RECV         4
 110
 111/* Device Controller Capability Parameter register */
 112#define DCCPARAMS_DC                            0x00000080
 113#define DCCPARAMS_DEN_MASK                      0x0000001f
 114
 115/* Frame Index Register Bit Masks */
 116#define USB_FRINDEX_MASKS                       0x3fff
 117/* USB CMD  Register Bit Masks */
 118#define  USB_CMD_RUN_STOP                     0x00000001
 119#define  USB_CMD_CTRL_RESET                   0x00000002
 120#define  USB_CMD_PERIODIC_SCHEDULE_EN         0x00000010
 121#define  USB_CMD_ASYNC_SCHEDULE_EN            0x00000020
 122#define  USB_CMD_INT_AA_DOORBELL              0x00000040
 123#define  USB_CMD_ASP                          0x00000300
 124#define  USB_CMD_ASYNC_SCH_PARK_EN            0x00000800
 125#define  USB_CMD_SUTW                         0x00002000
 126#define  USB_CMD_ATDTW                        0x00004000
 127#define  USB_CMD_ITC                          0x00FF0000
 128
 129/* bit 15,3,2 are frame list size */
 130#define  USB_CMD_FRAME_SIZE_1024              0x00000000
 131#define  USB_CMD_FRAME_SIZE_512               0x00000004
 132#define  USB_CMD_FRAME_SIZE_256               0x00000008
 133#define  USB_CMD_FRAME_SIZE_128               0x0000000C
 134#define  USB_CMD_FRAME_SIZE_64                0x00008000
 135#define  USB_CMD_FRAME_SIZE_32                0x00008004
 136#define  USB_CMD_FRAME_SIZE_16                0x00008008
 137#define  USB_CMD_FRAME_SIZE_8                 0x0000800C
 138
 139/* bit 9-8 are async schedule park mode count */
 140#define  USB_CMD_ASP_00                       0x00000000
 141#define  USB_CMD_ASP_01                       0x00000100
 142#define  USB_CMD_ASP_10                       0x00000200
 143#define  USB_CMD_ASP_11                       0x00000300
 144#define  USB_CMD_ASP_BIT_POS                  8
 145
 146/* bit 23-16 are interrupt threshold control */
 147#define  USB_CMD_ITC_NO_THRESHOLD             0x00000000
 148#define  USB_CMD_ITC_1_MICRO_FRM              0x00010000
 149#define  USB_CMD_ITC_2_MICRO_FRM              0x00020000
 150#define  USB_CMD_ITC_4_MICRO_FRM              0x00040000
 151#define  USB_CMD_ITC_8_MICRO_FRM              0x00080000
 152#define  USB_CMD_ITC_16_MICRO_FRM             0x00100000
 153#define  USB_CMD_ITC_32_MICRO_FRM             0x00200000
 154#define  USB_CMD_ITC_64_MICRO_FRM             0x00400000
 155#define  USB_CMD_ITC_BIT_POS                  16
 156
 157/* USB STS Register Bit Masks */
 158#define  USB_STS_INT                          0x00000001
 159#define  USB_STS_ERR                          0x00000002
 160#define  USB_STS_PORT_CHANGE                  0x00000004
 161#define  USB_STS_FRM_LST_ROLL                 0x00000008
 162#define  USB_STS_SYS_ERR                      0x00000010
 163#define  USB_STS_IAA                          0x00000020
 164#define  USB_STS_RESET                        0x00000040
 165#define  USB_STS_SOF                          0x00000080
 166#define  USB_STS_SUSPEND                      0x00000100
 167#define  USB_STS_HC_HALTED                    0x00001000
 168#define  USB_STS_RCL                          0x00002000
 169#define  USB_STS_PERIODIC_SCHEDULE            0x00004000
 170#define  USB_STS_ASYNC_SCHEDULE               0x00008000
 171
 172/* USB INTR Register Bit Masks */
 173#define  USB_INTR_INT_EN                      0x00000001
 174#define  USB_INTR_ERR_INT_EN                  0x00000002
 175#define  USB_INTR_PTC_DETECT_EN               0x00000004
 176#define  USB_INTR_FRM_LST_ROLL_EN             0x00000008
 177#define  USB_INTR_SYS_ERR_EN                  0x00000010
 178#define  USB_INTR_ASYN_ADV_EN                 0x00000020
 179#define  USB_INTR_RESET_EN                    0x00000040
 180#define  USB_INTR_SOF_EN                      0x00000080
 181#define  USB_INTR_DEVICE_SUSPEND              0x00000100
 182
 183/* Device Address bit masks */
 184#define  USB_DEVICE_ADDRESS_MASK              0xFE000000
 185#define  USB_DEVICE_ADDRESS_BIT_POS           25
 186
 187/* endpoint list address bit masks */
 188#define USB_EP_LIST_ADDRESS_MASK              0xfffff800
 189
 190/* PORTSCX  Register Bit Masks */
 191#define  PORTSCX_CURRENT_CONNECT_STATUS       0x00000001
 192#define  PORTSCX_CONNECT_STATUS_CHANGE        0x00000002
 193#define  PORTSCX_PORT_ENABLE                  0x00000004
 194#define  PORTSCX_PORT_EN_DIS_CHANGE           0x00000008
 195#define  PORTSCX_OVER_CURRENT_ACT             0x00000010
 196#define  PORTSCX_OVER_CURRENT_CHG             0x00000020
 197#define  PORTSCX_PORT_FORCE_RESUME            0x00000040
 198#define  PORTSCX_PORT_SUSPEND                 0x00000080
 199#define  PORTSCX_PORT_RESET                   0x00000100
 200#define  PORTSCX_LINE_STATUS_BITS             0x00000C00
 201#define  PORTSCX_PORT_POWER                   0x00001000
 202#define  PORTSCX_PORT_INDICTOR_CTRL           0x0000C000
 203#define  PORTSCX_PORT_TEST_CTRL               0x000F0000
 204#define  PORTSCX_WAKE_ON_CONNECT_EN           0x00100000
 205#define  PORTSCX_WAKE_ON_CONNECT_DIS          0x00200000
 206#define  PORTSCX_WAKE_ON_OVER_CURRENT         0x00400000
 207#define  PORTSCX_PHY_LOW_POWER_SPD            0x00800000
 208#define  PORTSCX_PORT_FORCE_FULL_SPEED        0x01000000
 209#define  PORTSCX_PORT_SPEED_MASK              0x0C000000
 210#define  PORTSCX_PORT_WIDTH                   0x10000000
 211#define  PORTSCX_PHY_TYPE_SEL                 0xC0000000
 212
 213/* bit 11-10 are line status */
 214#define  PORTSCX_LINE_STATUS_SE0              0x00000000
 215#define  PORTSCX_LINE_STATUS_JSTATE           0x00000400
 216#define  PORTSCX_LINE_STATUS_KSTATE           0x00000800
 217#define  PORTSCX_LINE_STATUS_UNDEF            0x00000C00
 218#define  PORTSCX_LINE_STATUS_BIT_POS          10
 219
 220/* bit 15-14 are port indicator control */
 221#define  PORTSCX_PIC_OFF                      0x00000000
 222#define  PORTSCX_PIC_AMBER                    0x00004000
 223#define  PORTSCX_PIC_GREEN                    0x00008000
 224#define  PORTSCX_PIC_UNDEF                    0x0000C000
 225#define  PORTSCX_PIC_BIT_POS                  14
 226
 227/* bit 19-16 are port test control */
 228#define  PORTSCX_PTC_DISABLE                  0x00000000
 229#define  PORTSCX_PTC_JSTATE                   0x00010000
 230#define  PORTSCX_PTC_KSTATE                   0x00020000
 231#define  PORTSCX_PTC_SEQNAK                   0x00030000
 232#define  PORTSCX_PTC_PACKET                   0x00040000
 233#define  PORTSCX_PTC_FORCE_EN                 0x00050000
 234#define  PORTSCX_PTC_BIT_POS                  16
 235
 236/* bit 27-26 are port speed */
 237#define  PORTSCX_PORT_SPEED_FULL              0x00000000
 238#define  PORTSCX_PORT_SPEED_LOW               0x04000000
 239#define  PORTSCX_PORT_SPEED_HIGH              0x08000000
 240#define  PORTSCX_PORT_SPEED_UNDEF             0x0C000000
 241#define  PORTSCX_SPEED_BIT_POS                26
 242
 243/* bit 28 is parallel transceiver width for UTMI interface */
 244#define  PORTSCX_PTW                          0x10000000
 245#define  PORTSCX_PTW_8BIT                     0x00000000
 246#define  PORTSCX_PTW_16BIT                    0x10000000
 247
 248/* bit 31-30 are port transceiver select */
 249#define  PORTSCX_PTS_UTMI                     0x00000000
 250#define  PORTSCX_PTS_ULPI                     0x80000000
 251#define  PORTSCX_PTS_FSLS                     0xC0000000
 252#define  PORTSCX_PTS_BIT_POS                  30
 253
 254/* otgsc Register Bit Masks */
 255#define  OTGSC_CTRL_VUSB_DISCHARGE            0x00000001
 256#define  OTGSC_CTRL_VUSB_CHARGE               0x00000002
 257#define  OTGSC_CTRL_OTG_TERM                  0x00000008
 258#define  OTGSC_CTRL_DATA_PULSING              0x00000010
 259#define  OTGSC_STS_USB_ID                     0x00000100
 260#define  OTGSC_STS_A_VBUS_VALID               0x00000200
 261#define  OTGSC_STS_A_SESSION_VALID            0x00000400
 262#define  OTGSC_STS_B_SESSION_VALID            0x00000800
 263#define  OTGSC_STS_B_SESSION_END              0x00001000
 264#define  OTGSC_STS_1MS_TOGGLE                 0x00002000
 265#define  OTGSC_STS_DATA_PULSING               0x00004000
 266#define  OTGSC_INTSTS_USB_ID                  0x00010000
 267#define  OTGSC_INTSTS_A_VBUS_VALID            0x00020000
 268#define  OTGSC_INTSTS_A_SESSION_VALID         0x00040000
 269#define  OTGSC_INTSTS_B_SESSION_VALID         0x00080000
 270#define  OTGSC_INTSTS_B_SESSION_END           0x00100000
 271#define  OTGSC_INTSTS_1MS                     0x00200000
 272#define  OTGSC_INTSTS_DATA_PULSING            0x00400000
 273#define  OTGSC_INTR_USB_ID                    0x01000000
 274#define  OTGSC_INTR_A_VBUS_VALID              0x02000000
 275#define  OTGSC_INTR_A_SESSION_VALID           0x04000000
 276#define  OTGSC_INTR_B_SESSION_VALID           0x08000000
 277#define  OTGSC_INTR_B_SESSION_END             0x10000000
 278#define  OTGSC_INTR_1MS_TIMER                 0x20000000
 279#define  OTGSC_INTR_DATA_PULSING              0x40000000
 280
 281/* USB MODE Register Bit Masks */
 282#define  USB_MODE_CTRL_MODE_IDLE              0x00000000
 283#define  USB_MODE_CTRL_MODE_DEVICE            0x00000002
 284#define  USB_MODE_CTRL_MODE_HOST              0x00000003
 285#define  USB_MODE_CTRL_MODE_MASK              0x00000003
 286#define  USB_MODE_CTRL_MODE_RSV               0x00000001
 287#define  USB_MODE_ES                          0x00000004 /* Endian Select */
 288#define  USB_MODE_SETUP_LOCK_OFF              0x00000008
 289#define  USB_MODE_STREAM_DISABLE              0x00000010
 290/* Endpoint Flush Register */
 291#define EPFLUSH_TX_OFFSET                     0x00010000
 292#define EPFLUSH_RX_OFFSET                     0x00000000
 293
 294/* Endpoint Setup Status bit masks */
 295#define  EP_SETUP_STATUS_MASK                 0x0000003F
 296#define  EP_SETUP_STATUS_EP0                  0x00000001
 297
 298/* ENDPOINTCTRLx  Register Bit Masks */
 299#define  EPCTRL_TX_ENABLE                     0x00800000
 300#define  EPCTRL_TX_DATA_TOGGLE_RST            0x00400000        /* Not EP0 */
 301#define  EPCTRL_TX_DATA_TOGGLE_INH            0x00200000        /* Not EP0 */
 302#define  EPCTRL_TX_TYPE                       0x000C0000
 303#define  EPCTRL_TX_DATA_SOURCE                0x00020000        /* Not EP0 */
 304#define  EPCTRL_TX_EP_STALL                   0x00010000
 305#define  EPCTRL_RX_ENABLE                     0x00000080
 306#define  EPCTRL_RX_DATA_TOGGLE_RST            0x00000040        /* Not EP0 */
 307#define  EPCTRL_RX_DATA_TOGGLE_INH            0x00000020        /* Not EP0 */
 308#define  EPCTRL_RX_TYPE                       0x0000000C
 309#define  EPCTRL_RX_DATA_SINK                  0x00000002        /* Not EP0 */
 310#define  EPCTRL_RX_EP_STALL                   0x00000001
 311
 312/* bit 19-18 and 3-2 are endpoint type */
 313#define  EPCTRL_EP_TYPE_CONTROL               0
 314#define  EPCTRL_EP_TYPE_ISO                   1
 315#define  EPCTRL_EP_TYPE_BULK                  2
 316#define  EPCTRL_EP_TYPE_INTERRUPT             3
 317#define  EPCTRL_TX_EP_TYPE_SHIFT              18
 318#define  EPCTRL_RX_EP_TYPE_SHIFT              2
 319
 320/* SNOOPn Register Bit Masks */
 321#define  SNOOP_ADDRESS_MASK                   0xFFFFF000
 322#define  SNOOP_SIZE_ZERO                      0x00      /* snooping disable */
 323#define  SNOOP_SIZE_4KB                       0x0B      /* 4KB snoop size */
 324#define  SNOOP_SIZE_8KB                       0x0C
 325#define  SNOOP_SIZE_16KB                      0x0D
 326#define  SNOOP_SIZE_32KB                      0x0E
 327#define  SNOOP_SIZE_64KB                      0x0F
 328#define  SNOOP_SIZE_128KB                     0x10
 329#define  SNOOP_SIZE_256KB                     0x11
 330#define  SNOOP_SIZE_512KB                     0x12
 331#define  SNOOP_SIZE_1MB                       0x13
 332#define  SNOOP_SIZE_2MB                       0x14
 333#define  SNOOP_SIZE_4MB                       0x15
 334#define  SNOOP_SIZE_8MB                       0x16
 335#define  SNOOP_SIZE_16MB                      0x17
 336#define  SNOOP_SIZE_32MB                      0x18
 337#define  SNOOP_SIZE_64MB                      0x19
 338#define  SNOOP_SIZE_128MB                     0x1A
 339#define  SNOOP_SIZE_256MB                     0x1B
 340#define  SNOOP_SIZE_512MB                     0x1C
 341#define  SNOOP_SIZE_1GB                       0x1D
 342#define  SNOOP_SIZE_2GB                       0x1E      /* 2GB snoop size */
 343
 344/* pri_ctrl Register Bit Masks */
 345#define  PRI_CTRL_PRI_LVL1                    0x0000000C
 346#define  PRI_CTRL_PRI_LVL0                    0x00000003
 347
 348/* si_ctrl Register Bit Masks */
 349#define  SI_CTRL_ERR_DISABLE                  0x00000010
 350#define  SI_CTRL_IDRC_DISABLE                 0x00000008
 351#define  SI_CTRL_RD_SAFE_EN                   0x00000004
 352#define  SI_CTRL_RD_PREFETCH_DISABLE          0x00000002
 353#define  SI_CTRL_RD_PREFEFETCH_VAL            0x00000001
 354
 355/* control Register Bit Masks */
 356#define  USB_CTRL_IOENB                       0x00000004
 357#define  USB_CTRL_ULPI_INT0EN                 0x00000001
 358#define USB_CTRL_UTMI_PHY_EN                  0x00000200
 359#define USB_CTRL_USB_EN                       0x00000004
 360#define USB_CTRL_ULPI_PHY_CLK_SEL             0x00000400
 361
 362/* Endpoint Queue Head data struct
 363 * Rem: all the variables of qh are LittleEndian Mode
 364 * and NEXT_POINTER_MASK should operate on a LittleEndian, Phy Addr
 365 */
 366struct ep_queue_head {
 367        u32 max_pkt_length;     /* Mult(31-30) , Zlt(29) , Max Pkt len
 368                                   and IOS(15) */
 369        u32 curr_dtd_ptr;       /* Current dTD Pointer(31-5) */
 370        u32 next_dtd_ptr;       /* Next dTD Pointer(31-5), T(0) */
 371        u32 size_ioc_int_sts;   /* Total bytes (30-16), IOC (15),
 372                                   MultO(11-10), STS (7-0)  */
 373        u32 buff_ptr0;          /* Buffer pointer Page 0 (31-12) */
 374        u32 buff_ptr1;          /* Buffer pointer Page 1 (31-12) */
 375        u32 buff_ptr2;          /* Buffer pointer Page 2 (31-12) */
 376        u32 buff_ptr3;          /* Buffer pointer Page 3 (31-12) */
 377        u32 buff_ptr4;          /* Buffer pointer Page 4 (31-12) */
 378        u32 res1;
 379        u8 setup_buffer[8];     /* Setup data 8 bytes */
 380        u32 res2[4];
 381};
 382
 383/* Endpoint Queue Head Bit Masks */
 384#define  EP_QUEUE_HEAD_MULT_POS               30
 385#define  EP_QUEUE_HEAD_ZLT_SEL                0x20000000
 386#define  EP_QUEUE_HEAD_MAX_PKT_LEN_POS        16
 387#define  EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info)   (((ep_info)>>16)&0x07ff)
 388#define  EP_QUEUE_HEAD_IOS                    0x00008000
 389#define  EP_QUEUE_HEAD_NEXT_TERMINATE         0x00000001
 390#define  EP_QUEUE_HEAD_IOC                    0x00008000
 391#define  EP_QUEUE_HEAD_MULTO                  0x00000C00
 392#define  EP_QUEUE_HEAD_STATUS_HALT            0x00000040
 393#define  EP_QUEUE_HEAD_STATUS_ACTIVE          0x00000080
 394#define  EP_QUEUE_CURRENT_OFFSET_MASK         0x00000FFF
 395#define  EP_QUEUE_HEAD_NEXT_POINTER_MASK      0xFFFFFFE0
 396#define  EP_QUEUE_FRINDEX_MASK                0x000007FF
 397#define  EP_MAX_LENGTH_TRANSFER               0x4000
 398
 399/* Endpoint Transfer Descriptor data struct */
 400/* Rem: all the variables of td are LittleEndian Mode */
 401struct ep_td_struct {
 402        u32 next_td_ptr;        /* Next TD pointer(31-5), T(0) set
 403                                   indicate invalid */
 404        u32 size_ioc_sts;       /* Total bytes (30-16), IOC (15),
 405                                   MultO(11-10), STS (7-0)  */
 406        u32 buff_ptr0;          /* Buffer pointer Page 0 */
 407        u32 buff_ptr1;          /* Buffer pointer Page 1 */
 408        u32 buff_ptr2;          /* Buffer pointer Page 2 */
 409        u32 buff_ptr3;          /* Buffer pointer Page 3 */
 410        u32 buff_ptr4;          /* Buffer pointer Page 4 */
 411        u32 res;
 412        /* 32 bytes */
 413        dma_addr_t td_dma;      /* dma address for this td */
 414        /* virtual address of next td specified in next_td_ptr */
 415        struct ep_td_struct *next_td_virt;
 416};
 417
 418/* Endpoint Transfer Descriptor bit Masks */
 419#define  DTD_NEXT_TERMINATE                   0x00000001
 420#define  DTD_IOC                              0x00008000
 421#define  DTD_STATUS_ACTIVE                    0x00000080
 422#define  DTD_STATUS_HALTED                    0x00000040
 423#define  DTD_STATUS_DATA_BUFF_ERR             0x00000020
 424#define  DTD_STATUS_TRANSACTION_ERR           0x00000008
 425#define  DTD_RESERVED_FIELDS                  0x80007300
 426#define  DTD_ADDR_MASK                        0xFFFFFFE0
 427#define  DTD_PACKET_SIZE                      0x7FFF0000
 428#define  DTD_LENGTH_BIT_POS                   16
 429#define  DTD_ERROR_MASK                       (DTD_STATUS_HALTED | \
 430                                               DTD_STATUS_DATA_BUFF_ERR | \
 431                                               DTD_STATUS_TRANSACTION_ERR)
 432/* Alignment requirements; must be a power of two */
 433#define DTD_ALIGNMENT                           0x20
 434#define QH_ALIGNMENT                            2048
 435
 436/* Controller dma boundary */
 437#define UDC_DMA_BOUNDARY                        0x1000
 438
 439/*-------------------------------------------------------------------------*/
 440
 441/* ### driver private data
 442 */
 443struct fsl_req {
 444        struct usb_request req;
 445        struct list_head queue;
 446        /* ep_queue() func will add
 447           a request->queue into a udc_ep->queue 'd tail */
 448        struct fsl_ep *ep;
 449        unsigned mapped:1;
 450
 451        struct ep_td_struct *head, *tail;       /* For dTD List
 452                                                   cpu endian Virtual addr */
 453        unsigned int dtd_count;
 454};
 455
 456#define REQ_UNCOMPLETE                  1
 457
 458struct fsl_ep {
 459        struct usb_ep ep;
 460        struct list_head queue;
 461        struct fsl_udc *udc;
 462        struct ep_queue_head *qh;
 463        struct usb_gadget *gadget;
 464
 465        char name[14];
 466        unsigned stopped:1;
 467};
 468
 469#define EP_DIR_IN       1
 470#define EP_DIR_OUT      0
 471
 472struct fsl_udc {
 473        struct usb_gadget gadget;
 474        struct usb_gadget_driver *driver;
 475        struct fsl_usb2_platform_data *pdata;
 476        struct completion *done;        /* to make sure release() is done */
 477        struct fsl_ep *eps;
 478        unsigned int max_ep;
 479        unsigned int irq;
 480
 481        struct usb_ctrlrequest local_setup_buff;
 482        spinlock_t lock;
 483        struct usb_phy *transceiver;
 484        unsigned softconnect:1;
 485        unsigned vbus_active:1;
 486        unsigned stopped:1;
 487        unsigned remote_wakeup:1;
 488        unsigned already_stopped:1;
 489        unsigned big_endian_desc:1;
 490
 491        struct ep_queue_head *ep_qh;    /* Endpoints Queue-Head */
 492        struct fsl_req *status_req;     /* ep0 status request */
 493        struct dma_pool *td_pool;       /* dma pool for DTD */
 494        enum fsl_usb2_phy_modes phy_mode;
 495
 496        size_t ep_qh_size;              /* size after alignment adjustment*/
 497        dma_addr_t ep_qh_dma;           /* dma address of QH */
 498
 499        u32 max_pipes;          /* Device max pipes */
 500        u32 bus_reset;          /* Device is bus resetting */
 501        u32 resume_state;       /* USB state to resume */
 502        u32 usb_state;          /* USB current state */
 503        u32 ep0_state;          /* Endpoint zero state */
 504        u32 ep0_dir;            /* Endpoint zero direction: can be
 505                                   USB_DIR_IN or USB_DIR_OUT */
 506        u8 device_address;      /* Device USB address */
 507};
 508
 509/*-------------------------------------------------------------------------*/
 510
 511#ifdef DEBUG
 512#define DBG(fmt, args...)       printk(KERN_DEBUG "[%s]  " fmt "\n", \
 513                                __func__, ## args)
 514#else
 515#define DBG(fmt, args...)       do{}while(0)
 516#endif
 517
 518#if 0
 519static void dump_msg(const char *label, const u8 * buf, unsigned int length)
 520{
 521        unsigned int start, num, i;
 522        char line[52], *p;
 523
 524        if (length >= 512)
 525                return;
 526        DBG("%s, length %u:\n", label, length);
 527        start = 0;
 528        while (length > 0) {
 529                num = min(length, 16u);
 530                p = line;
 531                for (i = 0; i < num; ++i) {
 532                        if (i == 8)
 533                                *p++ = ' ';
 534                        sprintf(p, " %02x", buf[i]);
 535                        p += 3;
 536                }
 537                *p = 0;
 538                printk(KERN_DEBUG "%6x: %s\n", start, line);
 539                buf += num;
 540                start += num;
 541                length -= num;
 542        }
 543}
 544#endif
 545
 546#ifdef VERBOSE
 547#define VDBG            DBG
 548#else
 549#define VDBG(stuff...)  do{}while(0)
 550#endif
 551
 552#define ERR(stuff...)           pr_err("udc: " stuff)
 553#define WARNING(stuff...)       pr_warn("udc: " stuff)
 554#define INFO(stuff...)          pr_info("udc: " stuff)
 555
 556/*-------------------------------------------------------------------------*/
 557
 558/* ### Add board specific defines here
 559 */
 560
 561/*
 562 * ### pipe direction macro from device view
 563 */
 564#define USB_RECV        0       /* OUT EP */
 565#define USB_SEND        1       /* IN EP */
 566
 567/*
 568 * ### internal used help routines.
 569 */
 570#define ep_index(EP)            ((EP)->ep.desc->bEndpointAddress&0xF)
 571#define ep_maxpacket(EP)        ((EP)->ep.maxpacket)
 572#define ep_is_in(EP)    ( (ep_index(EP) == 0) ? (EP->udc->ep0_dir == \
 573                        USB_DIR_IN) : ((EP)->ep.desc->bEndpointAddress \
 574                        & USB_DIR_IN)==USB_DIR_IN)
 575#define get_ep_by_pipe(udc, pipe)       ((pipe == 1)? &udc->eps[0]: \
 576                                        &udc->eps[pipe])
 577#define get_pipe_by_windex(windex)      ((windex & USB_ENDPOINT_NUMBER_MASK) \
 578                                        * 2 + ((windex & USB_DIR_IN) ? 1 : 0))
 579#define get_pipe_by_ep(EP)      (ep_index(EP) * 2 + ep_is_in(EP))
 580
 581static inline struct ep_queue_head *get_qh_by_ep(struct fsl_ep *ep)
 582{
 583        /* we only have one ep0 structure but two queue heads */
 584        if (ep_index(ep) != 0)
 585                return ep->qh;
 586        else
 587                return &ep->udc->ep_qh[(ep->udc->ep0_dir ==
 588                                USB_DIR_IN) ? 1 : 0];
 589}
 590
 591struct platform_device;
 592#ifdef CONFIG_ARCH_MXC
 593int fsl_udc_clk_init(struct platform_device *pdev);
 594int fsl_udc_clk_finalize(struct platform_device *pdev);
 595void fsl_udc_clk_release(void);
 596#else
 597static inline int fsl_udc_clk_init(struct platform_device *pdev)
 598{
 599        return 0;
 600}
 601static inline int fsl_udc_clk_finalize(struct platform_device *pdev)
 602{
 603        return 0;
 604}
 605static inline void fsl_udc_clk_release(void)
 606{
 607}
 608#endif
 609
 610#endif
 611