// SPDX-License-Identifier: GPL-2.0
/*
 * Silicon Laboratories CP210x USB to RS232 serial adaptor driver
 *
 * Copyright (C) 2005 Craig Shelley (craig@microtron.org.uk)
 *
 * Support to set flow control line levels using TIOCMGET and TIOCMSET
 * thanks to Karl Hiramoto karl@hiramoto.org. RTSCTS hardware flow
 * control thanks to Munir Nassar nassarmu@real-time.com
 *
 */

#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/usb.h>
#include <linux/uaccess.h>
#include <linux/usb/serial.h>
#include <linux/gpio/driver.h>
#include <linux/bitops.h>
#include <linux/mutex.h>

#define DRIVER_DESC "Silicon Labs CP210x RS232 serial adaptor driver"

/*
 * Function Prototypes
 */
static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *);
static void cp210x_close(struct usb_serial_port *);
static void cp210x_get_termios(struct tty_struct *, struct usb_serial_port *);
static void cp210x_get_termios_port(struct usb_serial_port *port,
        tcflag_t *cflagp, unsigned int *baudp);
static void cp210x_change_speed(struct tty_struct *, struct usb_serial_port *,
                                                        struct ktermios *);
static void cp210x_set_termios(struct tty_struct *, struct usb_serial_port *,
                                                        struct ktermios*);
static bool cp210x_tx_empty(struct usb_serial_port *port);
static int cp210x_tiocmget(struct tty_struct *);
static int cp210x_tiocmset(struct tty_struct *, unsigned int, unsigned int);
static int cp210x_tiocmset_port(struct usb_serial_port *port,
                unsigned int, unsigned int);
static void cp210x_break_ctl(struct tty_struct *, int);
static int cp210x_attach(struct usb_serial *);
static void cp210x_disconnect(struct usb_serial *);
static void cp210x_release(struct usb_serial *);
static int cp210x_port_probe(struct usb_serial_port *);
static int cp210x_port_remove(struct usb_serial_port *);
static void cp210x_dtr_rts(struct usb_serial_port *p, int on);

static const struct usb_device_id id_table[] = {
        { USB_DEVICE(0x045B, 0x0053) }, /* Renesas RX610 RX-Stick */
        { USB_DEVICE(0x0471, 0x066A) }, /* AKTAKOM ACE-1001 cable */
        { USB_DEVICE(0x0489, 0xE000) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
        { USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
        { USB_DEVICE(0x0745, 0x1000) }, /* CipherLab USB CCD Barcode Scanner 1000 */
        { USB_DEVICE(0x0846, 0x1100) }, /* NetGear Managed Switch M4100 series, M5300 series, M7100 series */
        { USB_DEVICE(0x08e6, 0x5501) }, /* Gemalto Prox-PU/CU contactless smartcard reader */
        { USB_DEVICE(0x08FD, 0x000A) }, /* Digianswer A/S , ZigBee/802.15.4 MAC Device */
        { USB_DEVICE(0x0908, 0x01FF) }, /* Siemens RUGGEDCOM USB Serial Console */
        { USB_DEVICE(0x0B00, 0x3070) }, /* Ingenico 3070 */
        { USB_DEVICE(0x0BED, 0x1100) }, /* MEI (TM) Cashflow-SC Bill/Voucher Acceptor */
        { USB_DEVICE(0x0BED, 0x1101) }, /* MEI series 2000 Combo Acceptor */
        { USB_DEVICE(0x0FCF, 0x1003) }, /* Dynastream ANT development board */
        { USB_DEVICE(0x0FCF, 0x1004) }, /* Dynastream ANT2USB */
        { USB_DEVICE(0x0FCF, 0x1006) }, /* Dynastream ANT development board */
        { USB_DEVICE(0x0FDE, 0xCA05) }, /* OWL Wireless Electricity Monitor CM-160 */
        { USB_DEVICE(0x10A6, 0xAA26) }, /* Knock-off DCU-11 cable */
        { USB_DEVICE(0x10AB, 0x10C5) }, /* Siemens MC60 Cable */
        { USB_DEVICE(0x10B5, 0xAC70) }, /* Nokia CA-42 USB */
        { USB_DEVICE(0x10C4, 0x0F91) }, /* Vstabi */
        { USB_DEVICE(0x10C4, 0x1101) }, /* Arkham Technology DS101 Bus Monitor */
        { USB_DEVICE(0x10C4, 0x1601) }, /* Arkham Technology DS101 Adapter */
        { USB_DEVICE(0x10C4, 0x800A) }, /* SPORTident BSM7-D-USB main station */
        { USB_DEVICE(0x10C4, 0x803B) }, /* Pololu USB-serial converter */
        { USB_DEVICE(0x10C4, 0x8044) }, /* Cygnal Debug Adapter */
        { USB_DEVICE(0x10C4, 0x804E) }, /* Software Bisque Paramount ME build-in converter */
        { USB_DEVICE(0x10C4, 0x8053) }, /* Enfora EDG1228 */
        { USB_DEVICE(0x10C4, 0x8054) }, /* Enfora GSM2228 */
        { USB_DEVICE(0x10C4, 0x8056) }, /* Lorenz Messtechnik devices */
        { USB_DEVICE(0x10C4, 0x8066) }, /* Argussoft In-System Programmer */
        { USB_DEVICE(0x10C4, 0x806F) }, /* IMS USB to RS422 Converter Cable */
        { USB_DEVICE(0x10C4, 0x807A) }, /* Crumb128 board */
        { USB_DEVICE(0x10C4, 0x80C4) }, /* Cygnal Integrated Products, Inc., Optris infrared thermometer */
        { USB_DEVICE(0x10C4, 0x80CA) }, /* Degree Controls Inc */
        { USB_DEVICE(0x10C4, 0x80DD) }, /* Tracient RFID */
        { USB_DEVICE(0x10C4, 0x80F6) }, /* Suunto sports instrument */
        { USB_DEVICE(0x10C4, 0x8115) }, /* Arygon NFC/Mifare Reader */
        { USB_DEVICE(0x10C4, 0x813D) }, /* Burnside Telecom Deskmobile */
        { USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */
        { USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */
        { USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */
        { USB_DEVICE(0x2405, 0x0003) }, /* West Mountain Radio RIGblaster Advantage */
        { USB_DEVICE(0x10C4, 0x8156) }, /* B&G H3000 link cable */
        { USB_DEVICE(0x10C4, 0x815E) }, /* Helicomm IP-Link 1220-DVM */
        { USB_DEVICE(0x10C4, 0x815F) }, /* Timewave HamLinkUSB */
        { USB_DEVICE(0x10C4, 0x817C) }, /* CESINEL MEDCAL N Power Quality Monitor */
        { USB_DEVICE(0x10C4, 0x817D) }, /* CESINEL MEDCAL NT Power Quality Monitor */
        { USB_DEVICE(0x10C4, 0x817E) }, /* CESINEL MEDCAL S Power Quality Monitor */
        { USB_DEVICE(0x10C4, 0x818B) }, /* AVIT Research USB to TTL */
        { USB_DEVICE(0x10C4, 0x819F) }, /* MJS USB Toslink Switcher */
        { USB_DEVICE(0x10C4, 0x81A6) }, /* ThinkOptics WavIt */
        { USB_DEVICE(0x10C4, 0x81A9) }, /* Multiplex RC Interface */
        { USB_DEVICE(0x10C4, 0x81AC) }, /* MSD Dash Hawk */
        { USB_DEVICE(0x10C4, 0x81AD) }, /* INSYS USB Modem */
        { USB_DEVICE(0x10C4, 0x81C8) }, /* Lipowsky Industrie Elektronik GmbH, Baby-JTAG */
        { USB_DEVICE(0x10C4, 0x81D7) }, /* IAI Corp. RCB-CV-USB USB to RS485 Adaptor */
        { USB_DEVICE(0x10C4, 0x81E2) }, /* Lipowsky Industrie Elektronik GmbH, Baby-LIN */
        { USB_DEVICE(0x10C4, 0x81E7) }, /* Aerocomm Radio */
        { USB_DEVICE(0x10C4, 0x81E8) }, /* Zephyr Bioharness */
        { USB_DEVICE(0x10C4, 0x81F2) }, /* C1007 HF band RFID controller */
        { USB_DEVICE(0x10C4, 0x8218) }, /* Lipowsky Industrie Elektronik GmbH, HARP-1 */
        { USB_DEVICE(0x10C4, 0x822B) }, /* Modem EDGE(GSM) Comander 2 */
        { USB_DEVICE(0x10C4, 0x826B) }, /* Cygnal Integrated Products, Inc., Fasttrax GPS demonstration module */
        { USB_DEVICE(0x10C4, 0x8281) }, /* Nanotec Plug & Drive */
        { USB_DEVICE(0x10C4, 0x8293) }, /* Telegesis ETRX2USB */
        { USB_DEVICE(0x10C4, 0x82EF) }, /* CESINEL FALCO 6105 AC Power Supply */
        { USB_DEVICE(0x10C4, 0x82F1) }, /* CESINEL MEDCAL EFD Earth Fault Detector */
        { USB_DEVICE(0x10C4, 0x82F2) }, /* CESINEL MEDCAL ST Network Analyzer */
        { USB_DEVICE(0x10C4, 0x82F4) }, /* Starizona MicroTouch */
        { USB_DEVICE(0x10C4, 0x82F9) }, /* Procyon AVS */
        { USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */
        { USB_DEVICE(0x10C4, 0x8382) }, /* Cygnal Integrated Products, Inc. */
        { USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */
        { USB_DEVICE(0x10C4, 0x83D8) }, /* DekTec DTA Plus VHF/UHF Booster/Attenuator */
        { USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */
        { USB_DEVICE(0x10C4, 0x8418) }, /* IRZ Automation Teleport SG-10 GSM/GPRS Modem */
        { USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */
        { USB_DEVICE(0x10C4, 0x8470) }, /* Juniper Networks BX Series System Console */
        { USB_DEVICE(0x10C4, 0x8477) }, /* Balluff RFID */
        { USB_DEVICE(0x10C4, 0x84B6) }, /* Starizona Hyperion */
        { USB_DEVICE(0x10C4, 0x851E) }, /* CESINEL MEDCAL PT Network Analyzer */
        { USB_DEVICE(0x10C4, 0x85A7) }, /* LifeScan OneTouch Verio IQ */
        { USB_DEVICE(0x10C4, 0x85B8) }, /* CESINEL ReCon T Energy Logger */
        { USB_DEVICE(0x10C4, 0x85EA) }, /* AC-Services IBUS-IF */
        { USB_DEVICE(0x10C4, 0x85EB) }, /* AC-Services CIS-IBUS */
        { USB_DEVICE(0x10C4, 0x85F8) }, /* Virtenio Preon32 */
        { USB_DEVICE(0x10C4, 0x8664) }, /* AC-Services CAN-IF */
        { USB_DEVICE(0x10C4, 0x8665) }, /* AC-Services OBD-IF */
        { USB_DEVICE(0x10C4, 0x8856) }, /* CEL EM357 ZigBee USB Stick - LR */
        { USB_DEVICE(0x10C4, 0x8857) }, /* CEL EM357 ZigBee USB Stick */
        { USB_DEVICE(0x10C4, 0x88A4) }, /* MMB Networks ZigBee USB Device */
        { USB_DEVICE(0x10C4, 0x88A5) }, /* Planet Innovation Ingeni ZigBee USB Device */
        { USB_DEVICE(0x10C4, 0x88FB) }, /* CESINEL MEDCAL STII Network Analyzer */
        { USB_DEVICE(0x10C4, 0x8938) }, /* CESINEL MEDCAL S II Network Analyzer */
        { USB_DEVICE(0x10C4, 0x8946) }, /* Ketra N1 Wireless Interface */
        { USB_DEVICE(0x10C4, 0x8962) }, /* Brim Brothers charging dock */
        { USB_DEVICE(0x10C4, 0x8977) }, /* CEL MeshWorks DevKit Device */
        { USB_DEVICE(0x10C4, 0x8998) }, /* KCF Technologies PRN */
        { USB_DEVICE(0x10C4, 0x89A4) }, /* CESINEL FTBC Flexible Thyristor Bridge Controller */
        { USB_DEVICE(0x10C4, 0x89FB) }, /* Qivicon ZigBee USB Radio Stick */
        { USB_DEVICE(0x10C4, 0x8A2A) }, /* HubZ dual ZigBee and Z-Wave dongle */
        { USB_DEVICE(0x10C4, 0x8A5E) }, /* CEL EM3588 ZigBee USB Stick Long Range */
        { USB_DEVICE(0x10C4, 0x8B34) }, /* Qivicon ZigBee USB Radio Stick */
        { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
        { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
        { USB_DEVICE(0x10C4, 0xEA63) }, /* Silicon Labs Windows Update (CP2101-4/CP2102N) */
        { USB_DEVICE(0x10C4, 0xEA70) }, /* Silicon Labs factory default */
        { USB_DEVICE(0x10C4, 0xEA71) }, /* Infinity GPS-MIC-1 Radio Monophone */
        { USB_DEVICE(0x10C4, 0xEA7A) }, /* Silicon Labs Windows Update (CP2105) */
        { USB_DEVICE(0x10C4, 0xEA7B) }, /* Silicon Labs Windows Update (CP2108) */
        { USB_DEVICE(0x10C4, 0xF001) }, /* Elan Digital Systems USBscope50 */
        { USB_DEVICE(0x10C4, 0xF002) }, /* Elan Digital Systems USBwave12 */
        { USB_DEVICE(0x10C4, 0xF003) }, /* Elan Digital Systems USBpulse100 */
        { USB_DEVICE(0x10C4, 0xF004) }, /* Elan Digital Systems USBcount50 */
        { USB_DEVICE(0x10C5, 0xEA61) }, /* Silicon Labs MobiData GPRS USB Modem */
        { USB_DEVICE(0x10CE, 0xEA6A) }, /* Silicon Labs MobiData GPRS USB Modem 100EU */
        { USB_DEVICE(0x12B8, 0xEC60) }, /* Link G4 ECU */
        { USB_DEVICE(0x12B8, 0xEC62) }, /* Link G4+ ECU */
        { USB_DEVICE(0x13AD, 0x9999) }, /* Baltech card reader */
        { USB_DEVICE(0x1555, 0x0004) }, /* Owen AC4 USB-RS485 Converter */
        { USB_DEVICE(0x155A, 0x1006) }, /* ELDAT Easywave RX09 */
        { USB_DEVICE(0x166A, 0x0201) }, /* Clipsal 5500PACA C-Bus Pascal Automation Controller */
        { USB_DEVICE(0x166A, 0x0301) }, /* Clipsal 5800PC C-Bus Wireless PC Interface */
        { USB_DEVICE(0x166A, 0x0303) }, /* Clipsal 5500PCU C-Bus USB interface */
        { USB_DEVICE(0x166A, 0x0304) }, /* Clipsal 5000CT2 C-Bus Black and White Touchscreen */
        { USB_DEVICE(0x166A, 0x0305) }, /* Clipsal C-5000CT2 C-Bus Spectrum Colour Touchscreen */
        { USB_DEVICE(0x166A, 0x0401) }, /* Clipsal L51xx C-Bus Architectural Dimmer */
        { USB_DEVICE(0x166A, 0x0101) }, /* Clipsal 5560884 C-Bus Multi-room Audio Matrix Switcher */
        { USB_DEVICE(0x16C0, 0x09B0) }, /* Lunatico Seletek */
        { USB_DEVICE(0x16C0, 0x09B1) }, /* Lunatico Seletek */
        { USB_DEVICE(0x16D6, 0x0001) }, /* Jablotron serial interface */
        { USB_DEVICE(0x16DC, 0x0010) }, /* W-IE-NE-R Plein & Baus GmbH PL512 Power Supply */
        { USB_DEVICE(0x16DC, 0x0011) }, /* W-IE-NE-R Plein & Baus GmbH RCM Remote Control for MARATON Power Supply */
        { USB_DEVICE(0x16DC, 0x0012) }, /* W-IE-NE-R Plein & Baus GmbH MPOD Multi Channel Power Supply */
        { USB_DEVICE(0x16DC, 0x0015) }, /* W-IE-NE-R Plein & Baus GmbH CML Control, Monitoring and Data Logger */
        { USB_DEVICE(0x17A8, 0x0001) }, /* Kamstrup Optical Eye/3-wire */
        { USB_DEVICE(0x17A8, 0x0005) }, /* Kamstrup M-Bus Master MultiPort 250D */
        { USB_DEVICE(0x17F4, 0xAAAA) }, /* Wavesense Jazz blood glucose meter */
        { USB_DEVICE(0x1843, 0x0200) }, /* Vaisala USB Instrument Cable */
        { USB_DEVICE(0x18EF, 0xE00F) }, /* ELV USB-I2C-Interface */
        { USB_DEVICE(0x18EF, 0xE025) }, /* ELV Marble Sound Board 1 */
        { USB_DEVICE(0x18EF, 0xE030) }, /* ELV ALC 8xxx Battery Charger */
        { USB_DEVICE(0x18EF, 0xE032) }, /* ELV TFD500 Data Logger */
        { USB_DEVICE(0x1901, 0x0190) }, /* GE B850 CP2105 Recorder interface */
        { USB_DEVICE(0x1901, 0x0193) }, /* GE B650 CP2104 PMC interface */
        { USB_DEVICE(0x1901, 0x0194) }, /* GE Healthcare Remote Alarm Box */
        { USB_DEVICE(0x1901, 0x0195) }, /* GE B850/B650/B450 CP2104 DP UART interface */
        { USB_DEVICE(0x1901, 0x0196) }, /* GE B850 CP2105 DP UART interface */
        { USB_DEVICE(0x19CF, 0x3000) }, /* Parrot NMEA GPS Flight Recorder */
        { USB_DEVICE(0x1ADB, 0x0001) }, /* Schweitzer Engineering C662 Cable */
        { USB_DEVICE(0x1B1C, 0x1C00) }, /* Corsair USB Dongle */
        { USB_DEVICE(0x1BA4, 0x0002) }, /* Silicon Labs 358x factory default */
        { USB_DEVICE(0x1BE3, 0x07A6) }, /* WAGO 750-923 USB Service Cable */
        { USB_DEVICE(0x1D6F, 0x0010) }, /* Seluxit ApS RF Dongle */
        { USB_DEVICE(0x1E29, 0x0102) }, /* Festo CPX-USB */
        { USB_DEVICE(0x1E29, 0x0501) }, /* Festo CMSP */
        { USB_DEVICE(0x1FB9, 0x0100) }, /* Lake Shore Model 121 Current Source */
        { USB_DEVICE(0x1FB9, 0x0200) }, /* Lake Shore Model 218A Temperature Monitor */
        { USB_DEVICE(0x1FB9, 0x0201) }, /* Lake Shore Model 219 Temperature Monitor */
        { USB_DEVICE(0x1FB9, 0x0202) }, /* Lake Shore Model 233 Temperature Transmitter */
        { USB_DEVICE(0x1FB9, 0x0203) }, /* Lake Shore Model 235 Temperature Transmitter */
        { USB_DEVICE(0x1FB9, 0x0300) }, /* Lake Shore Model 335 Temperature Controller */
        { USB_DEVICE(0x1FB9, 0x0301) }, /* Lake Shore Model 336 Temperature Controller */
        { USB_DEVICE(0x1FB9, 0x0302) }, /* Lake Shore Model 350 Temperature Controller */
        { USB_DEVICE(0x1FB9, 0x0303) }, /* Lake Shore Model 371 AC Bridge */
        { USB_DEVICE(0x1FB9, 0x0400) }, /* Lake Shore Model 411 Handheld Gaussmeter */
        { USB_DEVICE(0x1FB9, 0x0401) }, /* Lake Shore Model 425 Gaussmeter */
        { USB_DEVICE(0x1FB9, 0x0402) }, /* Lake Shore Model 455A Gaussmeter */
        { USB_DEVICE(0x1FB9, 0x0403) }, /* Lake Shore Model 475A Gaussmeter */
        { USB_DEVICE(0x1FB9, 0x0404) }, /* Lake Shore Model 465 Three Axis Gaussmeter */
        { USB_DEVICE(0x1FB9, 0x0600) }, /* Lake Shore Model 625A Superconducting MPS */
        { USB_DEVICE(0x1FB9, 0x0601) }, /* Lake Shore Model 642A Magnet Power Supply */
        { USB_DEVICE(0x1FB9, 0x0602) }, /* Lake Shore Model 648 Magnet Power Supply */
        { USB_DEVICE(0x1FB9, 0x0700) }, /* Lake Shore Model 737 VSM Controller */
        { USB_DEVICE(0x1FB9, 0x0701) }, /* Lake Shore Model 776 Hall Matrix */
        { USB_DEVICE(0x2626, 0xEA60) }, /* Aruba Networks 7xxx USB Serial Console */
        { USB_DEVICE(0x3195, 0xF190) }, /* Link Instruments MSO-19 */
        { USB_DEVICE(0x3195, 0xF280) }, /* Link Instruments MSO-28 */
        { USB_DEVICE(0x3195, 0xF281) }, /* Link Instruments MSO-28 */
        { USB_DEVICE(0x3923, 0x7A0B) }, /* National Instruments USB Serial Console */
        { USB_DEVICE(0x413C, 0x9500) }, /* DW700 GPS USB interface */
        { } /* Terminating Entry */
};

MODULE_DEVICE_TABLE(usb, id_table);

struct cp210x_serial_private {
#ifdef CONFIG_GPIOLIB
        struct gpio_chip        gc;
        bool                    gpio_registered;
        u8                      gpio_pushpull;
        u8                      gpio_altfunc;
        u8                      gpio_input;
#endif
        u8                      partnum;
        speed_t                 min_speed;
        speed_t                 max_speed;
        bool                    use_actual_rate;
};

struct cp210x_port_private {
        __u8                    bInterfaceNumber;
        bool                    has_swapped_line_ctl;
};

static struct usb_serial_driver cp210x_device = {
        .driver = {
                .owner =        THIS_MODULE,
                .name =         "cp210x",
        },
        .id_table               = id_table,
        .num_ports              = 1,
        .bulk_in_size           = 256,
        .bulk_out_size          = 256,
        .open                   = cp210x_open,
        .close                  = cp210x_close,
        .break_ctl              = cp210x_break_ctl,
        .set_termios            = cp210x_set_termios,
        .tx_empty               = cp210x_tx_empty,
        .tiocmget               = cp210x_tiocmget,
        .tiocmset               = cp210x_tiocmset,
        .attach                 = cp210x_attach,
        .disconnect             = cp210x_disconnect,
        .release                = cp210x_release,
        .port_probe             = cp210x_port_probe,
        .port_remove            = cp210x_port_remove,
        .dtr_rts                = cp210x_dtr_rts
};

static struct usb_serial_driver * const serial_drivers[] = {
        &cp210x_device, NULL
};

/* Config request types */
#define REQTYPE_HOST_TO_INTERFACE       0x41
#define REQTYPE_INTERFACE_TO_HOST       0xc1
#define REQTYPE_HOST_TO_DEVICE  0x40
#define REQTYPE_DEVICE_TO_HOST  0xc0

/* Config request codes */
#define CP210X_IFC_ENABLE       0x00
#define CP210X_SET_BAUDDIV      0x01
#define CP210X_GET_BAUDDIV      0x02
#define CP210X_SET_LINE_CTL     0x03
#define CP210X_GET_LINE_CTL     0x04
#define CP210X_SET_BREAK        0x05
#define CP210X_IMM_CHAR         0x06
#define CP210X_SET_MHS          0x07
#define CP210X_GET_MDMSTS       0x08
#define CP210X_SET_XON          0x09
#define CP210X_SET_XOFF         0x0A
#define CP210X_SET_EVENTMASK    0x0B
#define CP210X_GET_EVENTMASK    0x0C
#define CP210X_SET_CHAR         0x0D
#define CP210X_GET_CHARS        0x0E
#define CP210X_GET_PROPS        0x0F
#define CP210X_GET_COMM_STATUS  0x10
#define CP210X_RESET            0x11
#define CP210X_PURGE            0x12
#define CP210X_SET_FLOW         0x13
#define CP210X_GET_FLOW         0x14
#define CP210X_EMBED_EVENTS     0x15
#define CP210X_GET_EVENTSTATE   0x16
#define CP210X_SET_CHARS        0x19
#define CP210X_GET_BAUDRATE     0x1D
#define CP210X_SET_BAUDRATE     0x1E
#define CP210X_VENDOR_SPECIFIC  0xFF

/* CP210X_IFC_ENABLE */
#define UART_ENABLE             0x0001
#define UART_DISABLE            0x0000

/* CP210X_(SET|GET)_BAUDDIV */
#define BAUD_RATE_GEN_FREQ      0x384000

/* CP210X_(SET|GET)_LINE_CTL */
#define BITS_DATA_MASK          0X0f00
#define BITS_DATA_5             0X0500
#define BITS_DATA_6             0X0600
#define BITS_DATA_7             0X0700
#define BITS_DATA_8             0X0800
#define BITS_DATA_9             0X0900

#define BITS_PARITY_MASK        0x00f0
#define BITS_PARITY_NONE        0x0000
#define BITS_PARITY_ODD         0x0010
#define BITS_PARITY_EVEN        0x0020
#define BITS_PARITY_MARK        0x0030
#define BITS_PARITY_SPACE       0x0040

#define BITS_STOP_MASK          0x000f
#define BITS_STOP_1             0x0000
#define BITS_STOP_1_5           0x0001
#define BITS_STOP_2             0x0002

/* CP210X_SET_BREAK */
#define BREAK_ON                0x0001
#define BREAK_OFF               0x0000

/* CP210X_(SET_MHS|GET_MDMSTS) */
#define CONTROL_DTR             0x0001
#define CONTROL_RTS             0x0002
#define CONTROL_CTS             0x0010
#define CONTROL_DSR             0x0020
#define CONTROL_RING            0x0040
#define CONTROL_DCD             0x0080
#define CONTROL_WRITE_DTR       0x0100
#define CONTROL_WRITE_RTS       0x0200

/* CP210X_VENDOR_SPECIFIC values */
#define CP210X_READ_2NCONFIG    0x000E
#define CP210X_READ_LATCH       0x00C2
#define CP210X_GET_PARTNUM      0x370B
#define CP210X_GET_PORTCONFIG   0x370C
#define CP210X_GET_DEVICEMODE   0x3711
#define CP210X_WRITE_LATCH      0x37E1

/* Part number definitions */
#define CP210X_PARTNUM_CP2101   0x01
#define CP210X_PARTNUM_CP2102   0x02
#define CP210X_PARTNUM_CP2103   0x03
#define CP210X_PARTNUM_CP2104   0x04
#define CP210X_PARTNUM_CP2105   0x05
#define CP210X_PARTNUM_CP2108   0x08
#define CP210X_PARTNUM_CP2102N_QFN28    0x20
#define CP210X_PARTNUM_CP2102N_QFN24    0x21
#define CP210X_PARTNUM_CP2102N_QFN20    0x22
#define CP210X_PARTNUM_UNKNOWN  0xFF

/* CP210X_GET_COMM_STATUS returns these 0x13 bytes */
struct cp210x_comm_status {
        __le32   ulErrors;
        __le32   ulHoldReasons;
        __le32   ulAmountInInQueue;
        __le32   ulAmountInOutQueue;
        u8       bEofReceived;
        u8       bWaitForImmediate;
        u8       bReserved;
} __packed;

/*
 * CP210X_PURGE - 16 bits passed in wValue of USB request.
 * SiLabs app note AN571 gives a strange description of the 4 bits:
 * bit 0 or bit 2 clears the transmit queue and 1 or 3 receive.
 * writing 1 to all, however, purges cp2108 well enough to avoid the hang.
 */
#define PURGE_ALL               0x000f

/* CP210X_GET_FLOW/CP210X_SET_FLOW read/write these 0x10 bytes */
struct cp210x_flow_ctl {
        __le32  ulControlHandshake;
        __le32  ulFlowReplace;
        __le32  ulXonLimit;
        __le32  ulXoffLimit;
} __packed;

/* cp210x_flow_ctl::ulControlHandshake */
#define CP210X_SERIAL_DTR_MASK          GENMASK(1, 0)
#define CP210X_SERIAL_DTR_SHIFT(_mode)  (_mode)
#define CP210X_SERIAL_CTS_HANDSHAKE     BIT(3)
#define CP210X_SERIAL_DSR_HANDSHAKE     BIT(4)
#define CP210X_SERIAL_DCD_HANDSHAKE     BIT(5)
#define CP210X_SERIAL_DSR_SENSITIVITY   BIT(6)

/* values for cp210x_flow_ctl::ulControlHandshake::CP210X_SERIAL_DTR_MASK */
#define CP210X_SERIAL_DTR_INACTIVE      0
#define CP210X_SERIAL_DTR_ACTIVE        1
#define CP210X_SERIAL_DTR_FLOW_CTL      2

/* cp210x_flow_ctl::ulFlowReplace */
#define CP210X_SERIAL_AUTO_TRANSMIT     BIT(0)
#define CP210X_SERIAL_AUTO_RECEIVE      BIT(1)
#define CP210X_SERIAL_ERROR_CHAR        BIT(2)
#define CP210X_SERIAL_NULL_STRIPPING    BIT(3)
#define CP210X_SERIAL_BREAK_CHAR        BIT(4)
#define CP210X_SERIAL_RTS_MASK          GENMASK(7, 6)
#define CP210X_SERIAL_RTS_SHIFT(_mode)  (_mode << 6)
#define CP210X_SERIAL_XOFF_CONTINUE     BIT(31)

/* values for cp210x_flow_ctl::ulFlowReplace::CP210X_SERIAL_RTS_MASK */
#define CP210X_SERIAL_RTS_INACTIVE      0
#define CP210X_SERIAL_RTS_ACTIVE        1
#define CP210X_SERIAL_RTS_FLOW_CTL      2

/* CP210X_VENDOR_SPECIFIC, CP210X_GET_DEVICEMODE call reads these 0x2 bytes. */
struct cp210x_pin_mode {
        u8      eci;
        u8      sci;
} __packed;

#define CP210X_PIN_MODE_MODEM           0
#define CP210X_PIN_MODE_GPIO            BIT(0)

/*
 * CP210X_VENDOR_SPECIFIC, CP210X_GET_PORTCONFIG call reads these 0xf bytes
 * on a CP2105 chip. Structure needs padding due to unused/unspecified bytes.
 */
struct cp210x_dual_port_config {
        __le16  gpio_mode;
        u8      __pad0[2];
        __le16  reset_state;
        u8      __pad1[4];
        __le16  suspend_state;
        u8      sci_cfg;
        u8      eci_cfg;
        u8      device_cfg;
} __packed;

/*
 * CP210X_VENDOR_SPECIFIC, CP210X_GET_PORTCONFIG call reads these 0xd bytes
 * on a CP2104 chip. Structure needs padding due to unused/unspecified bytes.
 */
struct cp210x_single_port_config {
        __le16  gpio_mode;
        u8      __pad0[2];
        __le16  reset_state;
        u8      __pad1[4];
        __le16  suspend_state;
        u8      device_cfg;
} __packed;

/* GPIO modes */
#define CP210X_SCI_GPIO_MODE_OFFSET     9
#define CP210X_SCI_GPIO_MODE_MASK       GENMASK(11, 9)

#define CP210X_ECI_GPIO_MODE_OFFSET     2
#define CP210X_ECI_GPIO_MODE_MASK       GENMASK(3, 2)

#define CP210X_GPIO_MODE_OFFSET         8
#define CP210X_GPIO_MODE_MASK           GENMASK(11, 8)

/* CP2105 port configuration values */
#define CP2105_GPIO0_TXLED_MODE         BIT(0)
#define CP2105_GPIO1_RXLED_MODE         BIT(1)
#define CP2105_GPIO1_RS485_MODE         BIT(2)

/* CP2104 port configuration values */
#define CP2104_GPIO0_TXLED_MODE         BIT(0)
#define CP2104_GPIO1_RXLED_MODE         BIT(1)
#define CP2104_GPIO2_RS485_MODE         BIT(2)

/* CP2102N configuration array indices */
#define CP210X_2NCONFIG_CONFIG_VERSION_IDX      2
#define CP210X_2NCONFIG_GPIO_MODE_IDX           581
#define CP210X_2NCONFIG_GPIO_RSTLATCH_IDX       587
#define CP210X_2NCONFIG_GPIO_CONTROL_IDX        600

/* CP210X_VENDOR_SPECIFIC, CP210X_WRITE_LATCH call writes these 0x2 bytes. */
struct cp210x_gpio_write {
        u8      mask;
        u8      state;
} __packed;

/*
 * Helper to get interface number when we only have struct usb_serial.
 */
static u8 cp210x_interface_num(struct usb_serial *serial)
{
        struct usb_host_interface *cur_altsetting;

        cur_altsetting = serial->interface->cur_altsetting;

        return cur_altsetting->desc.bInterfaceNumber;
}

/*
 * Reads a variable-sized block of CP210X_ registers, identified by req.
 * Returns data into buf in native USB byte order.
 */
static int cp210x_read_reg_block(struct usb_serial_port *port, u8 req,
                void *buf, int bufsize)
{
        struct usb_serial *serial = port->serial;
        struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
        void *dmabuf;
        int result;

        dmabuf = kmalloc(bufsize, GFP_KERNEL);
        if (!dmabuf) {
                /*
                 * FIXME Some callers don't bother to check for error,
                 * at least give them consistent junk until they are fixed
                 */
                memset(buf, 0, bufsize);
                return -ENOMEM;
        }

        result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
                        req, REQTYPE_INTERFACE_TO_HOST, 0,
                        port_priv->bInterfaceNumber, dmabuf, bufsize,
                        USB_CTRL_SET_TIMEOUT);
        if (result == bufsize) {
                memcpy(buf, dmabuf, bufsize);
                result = 0;
        } else {
                dev_err(&port->dev, "failed get req 0x%x size %d status: %d\n",
                                req, bufsize, result);
                if (result >= 0)
                        result = -EIO;

                /*
                 * FIXME Some callers don't bother to check for error,
                 * at least give them consistent junk until they are fixed
                 */
                memset(buf, 0, bufsize);
        }

        kfree(dmabuf);

        return result;
}

/*
 * Reads any 32-bit CP210X_ register identified by req.
 */
static int cp210x_read_u32_reg(struct usb_serial_port *port, u8 req, u32 *val)
{
        __le32 le32_val;
        int err;

        err = cp210x_read_reg_block(port, req, &le32_val, sizeof(le32_val));
        if (err) {
                /*
                 * FIXME Some callers don't bother to check for error,
                 * at least give them consistent junk until they are fixed
                 */
                *val = 0;
                return err;
        }

        *val = le32_to_cpu(le32_val);

        return 0;
}

/*
 * Reads any 16-bit CP210X_ register identified by req.
 */
static int cp210x_read_u16_reg(struct usb_serial_port *port, u8 req, u16 *val)
{
        __le16 le16_val;
        int err;

        err = cp210x_read_reg_block(port, req, &le16_val, sizeof(le16_val));
        if (err)
                return err;

        *val = le16_to_cpu(le16_val);

        return 0;
}

/*
 * Reads any 8-bit CP210X_ register identified by req.
 */
static int cp210x_read_u8_reg(struct usb_serial_port *port, u8 req, u8 *val)
{
        return cp210x_read_reg_block(port, req, val, sizeof(*val));
}

/*
 * Reads a variable-sized vendor block of CP210X_ registers, identified by val.
 * Returns data into buf in native USB byte order.
 */
static int cp210x_read_vendor_block(struct usb_serial *serial, u8 type, u16 val,
                                    void *buf, int bufsize)
{
        void *dmabuf;
        int result;

        dmabuf = kmalloc(bufsize, GFP_KERNEL);
        if (!dmabuf)
                return -ENOMEM;

        result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
                                 CP210X_VENDOR_SPECIFIC, type, val,
                                 cp210x_interface_num(serial), dmabuf, bufsize,
                                 USB_CTRL_GET_TIMEOUT);
        if (result == bufsize) {
                memcpy(buf, dmabuf, bufsize);
                result = 0;
        } else {
                dev_err(&serial->interface->dev,
                        "failed to get vendor val 0x%04x size %d: %d\n", val,
                        bufsize, result);
                if (result >= 0)
                        result = -EIO;
        }

        kfree(dmabuf);

        return result;
}

/*
 * Writes any 16-bit CP210X_ register (req) whose value is passed
 * entirely in the wValue field of the USB request.
 */
static int cp210x_write_u16_reg(struct usb_serial_port *port, u8 req, u16 val)
{
        struct usb_serial *serial = port->serial;
        struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
        int result;

        result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
                        req, REQTYPE_HOST_TO_INTERFACE, val,
                        port_priv->bInterfaceNumber, NULL, 0,
                        USB_CTRL_SET_TIMEOUT);
        if (result < 0) {
                dev_err(&port->dev, "failed set request 0x%x status: %d\n",
                                req, result);
        }

        return result;
}

/*
 * Writes a variable-sized block of CP210X_ registers, identified by req.
 * Data in buf must be in native USB byte order.
 */
static int cp210x_write_reg_block(struct usb_serial_port *port, u8 req,
                void *buf, int bufsize)
{
        struct usb_serial *serial = port->serial;
        struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
        void *dmabuf;
        int result;

        dmabuf = kmemdup(buf, bufsize, GFP_KERNEL);
        if (!dmabuf)
                return -ENOMEM;

        result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
                        req, REQTYPE_HOST_TO_INTERFACE, 0,
                        port_priv->bInterfaceNumber, dmabuf, bufsize,
                        USB_CTRL_SET_TIMEOUT);

        kfree(dmabuf);

        if (result == bufsize) {
                result = 0;
        } else {
                dev_err(&port->dev, "failed set req 0x%x size %d status: %d\n",
                                req, bufsize, result);
                if (result >= 0)
                        result = -EIO;
        }

        return result;
}

/*
 * Writes any 32-bit CP210X_ register identified by req.
 */
static int cp210x_write_u32_reg(struct usb_serial_port *port, u8 req, u32 val)
{
        __le32 le32_val;

        le32_val = cpu_to_le32(val);

        return cp210x_write_reg_block(port, req, &le32_val, sizeof(le32_val));
}

#ifdef CONFIG_GPIOLIB
/*
 * Writes a variable-sized vendor block of CP210X_ registers, identified by val.
 * Data in buf must be in native USB byte order.
 */
static int cp210x_write_vendor_block(struct usb_serial *serial, u8 type,
                                     u16 val, void *buf, int bufsize)
{
        void *dmabuf;
        int result;

        dmabuf = kmemdup(buf, bufsize, GFP_KERNEL);
        if (!dmabuf)
                return -ENOMEM;

        result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
                                 CP210X_VENDOR_SPECIFIC, type, val,
                                 cp210x_interface_num(serial), dmabuf, bufsize,
                                 USB_CTRL_SET_TIMEOUT);

        kfree(dmabuf);

        if (result == bufsize) {
                result = 0;
        } else {
                dev_err(&serial->interface->dev,
                        "failed to set vendor val 0x%04x size %d: %d\n", val,
                        bufsize, result);
                if (result >= 0)
                        result = -EIO;
        }

        return result;
}
#endif

/*
 * Detect CP2108 GET_LINE_CTL bug and activate workaround.
 * Write a known good value 0x800, read it back.
 * If it comes back swapped the bug is detected.
 * Preserve the original register value.
 */
static int cp210x_detect_swapped_line_ctl(struct usb_serial_port *port)
{
        struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
        u16 line_ctl_save;
        u16 line_ctl_test;
        int err;

        err = cp210x_read_u16_reg(port, CP210X_GET_LINE_CTL, &line_ctl_save);
        if (err)
                return err;

        err = cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, 0x800);
        if (err)
                return err;

        err = cp210x_read_u16_reg(port, CP210X_GET_LINE_CTL, &line_ctl_test);
        if (err)
                return err;

        if (line_ctl_test == 8) {
                port_priv->has_swapped_line_ctl = true;
                line_ctl_save = swab16(line_ctl_save);
        }

        return cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, line_ctl_save);
}

/*
 * Must always be called instead of cp210x_read_u16_reg(CP210X_GET_LINE_CTL)
 * to workaround cp2108 bug and get correct value.
 */
static int cp210x_get_line_ctl(struct usb_serial_port *port, u16 *ctl)
{
        struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
        int err;

        err = cp210x_read_u16_reg(port, CP210X_GET_LINE_CTL, ctl);
        if (err)
                return err;

        /* Workaround swapped bytes in 16-bit value from CP210X_GET_LINE_CTL */
        if (port_priv->has_swapped_line_ctl)
                *ctl = swab16(*ctl);

        return 0;
}

static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *port)
{
        int result;

        result = cp210x_write_u16_reg(port, CP210X_IFC_ENABLE, UART_ENABLE);
        if (result) {
                dev_err(&port->dev, "%s - Unable to enable UART\n", __func__);
                return result;
        }

        /* Configure the termios structure */
        cp210x_get_termios(tty, port);

        /* The baud rate must be initialised on cp2104 */
        if (tty)
                cp210x_change_speed(tty, port, NULL);

        return usb_serial_generic_open(tty, port);
}

static void cp210x_close(struct usb_serial_port *port)
{
        usb_serial_generic_close(port);

        /* Clear both queues; cp2108 needs this to avoid an occasional hang */
        cp210x_write_u16_reg(port, CP210X_PURGE, PURGE_ALL);

        cp210x_write_u16_reg(port, CP210X_IFC_ENABLE, UART_DISABLE);
}

/*
 * Read how many bytes are waiting in the TX queue.
 */
static int cp210x_get_tx_queue_byte_count(struct usb_serial_port *port,
                u32 *count)
{
        struct usb_serial *serial = port->serial;
        struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
        struct cp210x_comm_status *sts;
        int result;

        sts = kmalloc(sizeof(*sts), GFP_KERNEL);
        if (!sts)
                return -ENOMEM;

        result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
                        CP210X_GET_COMM_STATUS, REQTYPE_INTERFACE_TO_HOST,
                        0, port_priv->bInterfaceNumber, sts, sizeof(*sts),
                        USB_CTRL_GET_TIMEOUT);
        if (result == sizeof(*sts)) {
                *count = le32_to_cpu(sts->ulAmountInOutQueue);
                result = 0;
        } else {
                dev_err(&port->dev, "failed to get comm status: %d\n", result);
                if (result >= 0)
                        result = -EIO;
        }

        kfree(sts);

        return result;
}

static bool cp210x_tx_empty(struct usb_serial_port *port)
{
        int err;
        u32 count;

        err = cp210x_get_tx_queue_byte_count(port, &count);
        if (err)
                return true;

        return !count;
}

/*
 * cp210x_get_termios
 * Reads the baud rate, data bits, parity, stop bits and flow control mode
 * from the device, corrects any unsupported values, and configures the
 * termios structure to reflect the state of the device
 */
static void cp210x_get_termios(struct tty_struct *tty,
        struct usb_serial_port *port)
{
        unsigned int baud;

        if (tty) {
                cp210x_get_termios_port(tty->driver_data,
                        &tty->termios.c_cflag, &baud);
                tty_encode_baud_rate(tty, baud, baud);
        } else {
                tcflag_t cflag;
                cflag = 0;
                cp210x_get_termios_port(port, &cflag, &baud);
        }
}

/*
 * cp210x_get_termios_port
 * This is the heart of cp210x_get_termios which always uses a &usb_serial_port.
 */
static void cp210x_get_termios_port(struct usb_serial_port *port,
        tcflag_t *cflagp, unsigned int *baudp)
{
        struct device *dev = &port->dev;
        tcflag_t cflag;
        struct cp210x_flow_ctl flow_ctl;
        u32 baud;
        u16 bits;
        u32 ctl_hs;

        cp210x_read_u32_reg(port, CP210X_GET_BAUDRATE, &baud);

        dev_dbg(dev, "%s - baud rate = %d\n", __func__, baud);
        *baudp = baud;

        cflag = *cflagp;

        cp210x_get_line_ctl(port, &bits);
        cflag &= ~CSIZE;
        switch (bits & BITS_DATA_MASK) {
        case BITS_DATA_5:
                dev_dbg(dev, "%s - data bits = 5\n", __func__);
                cflag |= CS5;
                break;
        case BITS_DATA_6:
                dev_dbg(dev, "%s - data bits = 6\n", __func__);
                cflag |= CS6;
                break;
        case BITS_DATA_7:
                dev_dbg(dev, "%s - data bits = 7\n", __func__);
                cflag |= CS7;
                break;
        case BITS_DATA_8:
                dev_dbg(dev, "%s - data bits = 8\n", __func__);
                cflag |= CS8;
                break;
        case BITS_DATA_9:
                dev_dbg(dev, "%s - data bits = 9 (not supported, using 8 data bits)\n", __func__);
                cflag |= CS8;
                bits &= ~BITS_DATA_MASK;
                bits |= BITS_DATA_8;
                cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
                break;
        default:
                dev_dbg(dev, "%s - Unknown number of data bits, using 8\n", __func__);
                cflag |= CS8;
                bits &= ~BITS_DATA_MASK;
                bits |= BITS_DATA_8;
                cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
                break;
        }

        switch (bits & BITS_PARITY_MASK) {
        case BITS_PARITY_NONE:
                dev_dbg(dev, "%s - parity = NONE\n", __func__);
                cflag &= ~PARENB;
                break;
        case BITS_PARITY_ODD:
                dev_dbg(dev, "%s - parity = ODD\n", __func__);
                cflag |= (PARENB|PARODD);
                break;
        case BITS_PARITY_EVEN:
                dev_dbg(dev, "%s - parity = EVEN\n", __func__);
                cflag &= ~PARODD;
                cflag |= PARENB;
                break;
        case BITS_PARITY_MARK:
                dev_dbg(dev, "%s - parity = MARK\n", __func__);
                cflag |= (PARENB|PARODD|CMSPAR);
                break;
        case BITS_PARITY_SPACE:
                dev_dbg(dev, "%s - parity = SPACE\n", __func__);
                cflag &= ~PARODD;
                cflag |= (PARENB|CMSPAR);
                break;
        default:
                dev_dbg(dev, "%s - Unknown parity mode, disabling parity\n", __func__);
                cflag &= ~PARENB;
                bits &= ~BITS_PARITY_MASK;
                cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
                break;
        }

        cflag &= ~CSTOPB;
        switch (bits & BITS_STOP_MASK) {
        case BITS_STOP_1:
                dev_dbg(dev, "%s - stop bits = 1\n", __func__);
                break;
        case BITS_STOP_1_5:
                dev_dbg(dev, "%s - stop bits = 1.5 (not supported, using 1 stop bit)\n", __func__);
                bits &= ~BITS_STOP_MASK;
                cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
                break;

        case BITS_STOP_2:
                dev_dbg(dev, "%s - stop bits = 2\n", __func__);
                cflag |= CSTOPB;
                break;
        default:
                dev_dbg(dev, "%s - Unknown number of stop bits, using 1 stop bit\n", __func__);
                bits &= ~BITS_STOP_MASK;
                cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
                break;
        }

        cp210x_read_reg_block(port, CP210X_GET_FLOW, &flow_ctl,
                        sizeof(flow_ctl));
        ctl_hs = le32_to_cpu(flow_ctl.ulControlHandshake);
        if (ctl_hs & CP210X_SERIAL_CTS_HANDSHAKE) {
                dev_dbg(dev, "%s - flow control = CRTSCTS\n", __func__);
                cflag |= CRTSCTS;
        } else {
                dev_dbg(dev, "%s - flow control = NONE\n", __func__);
                cflag &= ~CRTSCTS;
        }

        *cflagp = cflag;
}

struct cp210x_rate {
        speed_t rate;
        speed_t high;
};

static const struct cp210x_rate cp210x_an205_table1[] = {
        { 300, 300 },
        { 600, 600 },
        { 1200, 1200 },
        { 1800, 1800 },
        { 2400, 2400 },
        { 4000, 4000 },
        { 4800, 4803 },
        { 7200, 7207 },
        { 9600, 9612 },
        { 14400, 14428 },
        { 16000, 16062 },
        { 19200, 19250 },
        { 28800, 28912 },
        { 38400, 38601 },
        { 51200, 51558 },
        { 56000, 56280 },
        { 57600, 58053 },
        { 64000, 64111 },
        { 76800, 77608 },
        { 115200, 117028 },
        { 128000, 129347 },
        { 153600, 156868 },
        { 230400, 237832 },
        { 250000, 254234 },
        { 256000, 273066 },
        { 460800, 491520 },
        { 500000, 567138 },
        { 576000, 670254 },
        { 921600, UINT_MAX }
};

/*
 * Quantises the baud rate as per AN205 Table 1
 */
static speed_t cp210x_get_an205_rate(speed_t baud)
{
        int i;

        for (i = 0; i < ARRAY_SIZE(cp210x_an205_table1); ++i) {
                if (baud <= cp210x_an205_table1[i].high)
                        break;
        }

        return cp210x_an205_table1[i].rate;
}

static speed_t cp210x_get_actual_rate(speed_t baud)
{
        unsigned int prescale = 1;
        unsigned int div;

        if (baud <= 365)
                prescale = 4;

        div = DIV_ROUND_CLOSEST(48000000, 2 * prescale * baud);
        baud = 48000000 / (2 * prescale * div);

        return baud;
}

/*
 * CP2101 supports the following baud rates:
 *
 *      300, 600, 1200, 1800, 2400, 4800, 7200, 9600, 14400, 19200, 28800,
 *      38400, 56000, 57600, 115200, 128000, 230400, 460800, 921600
 *
 * CP2102 and CP2103 support the following additional rates:
 *
 *      4000, 16000, 51200, 64000, 76800, 153600, 250000, 256000, 500000,
 *      576000
 *
 * The device will map a requested rate to a supported one, but the result
 * of requests for rates greater than 1053257 is undefined (see AN205).
 *
 * CP2104, CP2105 and CP2110 support most rates up to 2M, 921k and 1M baud,
 * respectively, with an error less than 1%. The actual rates are determined
 * by
 *
 *      div = round(freq / (2 x prescale x request))
 *      actual = freq / (2 x prescale x div)
 *
 * For CP2104 and CP2105 freq is 48Mhz and prescale is 4 for request <= 365bps
 * or 1 otherwise.
 * For CP2110 freq is 24Mhz and prescale is 4 for request <= 300bps or 1
 * otherwise.
 */
static void cp210x_change_speed(struct tty_struct *tty,
                struct usb_serial_port *port, struct ktermios *old_termios)
{
        struct usb_serial *serial = port->serial;
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);
        u32 baud;

        /*
         * This maps the requested rate to the actual rate, a valid rate on
         * cp2102 or cp2103, or to an arbitrary rate in [1M, max_speed].
         *
         * NOTE: B0 is not implemented.
         */
        baud = clamp(tty->termios.c_ospeed, priv->min_speed, priv->max_speed);

        if (priv->use_actual_rate)
                baud = cp210x_get_actual_rate(baud);
        else if (baud < 1000000)
                baud = cp210x_get_an205_rate(baud);

        dev_dbg(&port->dev, "%s - setting baud rate to %u\n", __func__, baud);
        if (cp210x_write_u32_reg(port, CP210X_SET_BAUDRATE, baud)) {
                dev_warn(&port->dev, "failed to set baud rate to %u\n", baud);
                if (old_termios)
                        baud = old_termios->c_ospeed;
                else
                        baud = 9600;
        }

        tty_encode_baud_rate(tty, baud, baud);
}

static void cp210x_set_termios(struct tty_struct *tty,
                struct usb_serial_port *port, struct ktermios *old_termios)
{
        struct device *dev = &port->dev;
        unsigned int cflag, old_cflag;
        u16 bits;

        cflag = tty->termios.c_cflag;
        old_cflag = old_termios->c_cflag;

        if (tty->termios.c_ospeed != old_termios->c_ospeed)
                cp210x_change_speed(tty, port, old_termios);

        /* If the number of data bits is to be updated */
        if ((cflag & CSIZE) != (old_cflag & CSIZE)) {
                cp210x_get_line_ctl(port, &bits);
                bits &= ~BITS_DATA_MASK;
                switch (cflag & CSIZE) {
                case CS5:
                        bits |= BITS_DATA_5;
                        dev_dbg(dev, "%s - data bits = 5\n", __func__);
                        break;
                case CS6:
                        bits |= BITS_DATA_6;
                        dev_dbg(dev, "%s - data bits = 6\n", __func__);
                        break;
                case CS7:
                        bits |= BITS_DATA_7;
                        dev_dbg(dev, "%s - data bits = 7\n", __func__);
                        break;
                case CS8:
                default:
                        bits |= BITS_DATA_8;
                        dev_dbg(dev, "%s - data bits = 8\n", __func__);
                        break;
                }
                if (cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits))
                        dev_dbg(dev, "Number of data bits requested not supported by device\n");
        }

        if ((cflag     & (PARENB|PARODD|CMSPAR)) !=
            (old_cflag & (PARENB|PARODD|CMSPAR))) {
                cp210x_get_line_ctl(port, &bits);
                bits &= ~BITS_PARITY_MASK;
                if (cflag & PARENB) {
                        if (cflag & CMSPAR) {
                                if (cflag & PARODD) {
                                        bits |= BITS_PARITY_MARK;
                                        dev_dbg(dev, "%s - parity = MARK\n", __func__);
                                } else {
                                        bits |= BITS_PARITY_SPACE;
                                        dev_dbg(dev, "%s - parity = SPACE\n", __func__);
                                }
                        } else {
                                if (cflag & PARODD) {
                                        bits |= BITS_PARITY_ODD;
                                        dev_dbg(dev, "%s - parity = ODD\n", __func__);
                                } else {
                                        bits |= BITS_PARITY_EVEN;
                                        dev_dbg(dev, "%s - parity = EVEN\n", __func__);
                                }
                        }
                }
                if (cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits))
                        dev_dbg(dev, "Parity mode not supported by device\n");
        }

        if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) {
                cp210x_get_line_ctl(port, &bits);
                bits &= ~BITS_STOP_MASK;
                if (cflag & CSTOPB) {
                        bits |= BITS_STOP_2;
                        dev_dbg(dev, "%s - stop bits = 2\n", __func__);
                } else {
                        bits |= BITS_STOP_1;
                        dev_dbg(dev, "%s - stop bits = 1\n", __func__);
                }
                if (cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits))
                        dev_dbg(dev, "Number of stop bits requested not supported by device\n");
        }

        if ((cflag & CRTSCTS) != (old_cflag & CRTSCTS)) {
                struct cp210x_flow_ctl flow_ctl;
                u32 ctl_hs;
                u32 flow_repl;

                cp210x_read_reg_block(port, CP210X_GET_FLOW, &flow_ctl,
                                sizeof(flow_ctl));
                ctl_hs = le32_to_cpu(flow_ctl.ulControlHandshake);
                flow_repl = le32_to_cpu(flow_ctl.ulFlowReplace);
                dev_dbg(dev, "%s - read ulControlHandshake=0x%08x, ulFlowReplace=0x%08x\n",
                                __func__, ctl_hs, flow_repl);

                ctl_hs &= ~CP210X_SERIAL_DSR_HANDSHAKE;
                ctl_hs &= ~CP210X_SERIAL_DCD_HANDSHAKE;
                ctl_hs &= ~CP210X_SERIAL_DSR_SENSITIVITY;
                ctl_hs &= ~CP210X_SERIAL_DTR_MASK;
                ctl_hs |= CP210X_SERIAL_DTR_SHIFT(CP210X_SERIAL_DTR_ACTIVE);
                if (cflag & CRTSCTS) {
                        ctl_hs |= CP210X_SERIAL_CTS_HANDSHAKE;

                        flow_repl &= ~CP210X_SERIAL_RTS_MASK;
                        flow_repl |= CP210X_SERIAL_RTS_SHIFT(
                                        CP210X_SERIAL_RTS_FLOW_CTL);
                        dev_dbg(dev, "%s - flow control = CRTSCTS\n", __func__);
                } else {
                        ctl_hs &= ~CP210X_SERIAL_CTS_HANDSHAKE;

                        flow_repl &= ~CP210X_SERIAL_RTS_MASK;
                        flow_repl |= CP210X_SERIAL_RTS_SHIFT(
                                        CP210X_SERIAL_RTS_ACTIVE);
                        dev_dbg(dev, "%s - flow control = NONE\n", __func__);
                }

                dev_dbg(dev, "%s - write ulControlHandshake=0x%08x, ulFlowReplace=0x%08x\n",
                                __func__, ctl_hs, flow_repl);
                flow_ctl.ulControlHandshake = cpu_to_le32(ctl_hs);
                flow_ctl.ulFlowReplace = cpu_to_le32(flow_repl);
                cp210x_write_reg_block(port, CP210X_SET_FLOW, &flow_ctl,
                                sizeof(flow_ctl));
        }

}

static int cp210x_tiocmset(struct tty_struct *tty,
                unsigned int set, unsigned int clear)
{
        struct usb_serial_port *port = tty->driver_data;
        return cp210x_tiocmset_port(port, set, clear);
}

static int cp210x_tiocmset_port(struct usb_serial_port *port,
                unsigned int set, unsigned int clear)
{
        u16 control = 0;

        if (set & TIOCM_RTS) {
                control |= CONTROL_RTS;
                control |= CONTROL_WRITE_RTS;
        }
        if (set & TIOCM_DTR) {
                control |= CONTROL_DTR;
                control |= CONTROL_WRITE_DTR;
        }
        if (clear & TIOCM_RTS) {
                control &= ~CONTROL_RTS;
                control |= CONTROL_WRITE_RTS;
        }
        if (clear & TIOCM_DTR) {
                control &= ~CONTROL_DTR;
                control |= CONTROL_WRITE_DTR;
        }

        dev_dbg(&port->dev, "%s - control = 0x%.4x\n", __func__, control);

        return cp210x_write_u16_reg(port, CP210X_SET_MHS, control);
}

static void cp210x_dtr_rts(struct usb_serial_port *p, int on)
{
        if (on)
                cp210x_tiocmset_port(p, TIOCM_DTR|TIOCM_RTS, 0);
        else
                cp210x_tiocmset_port(p, 0, TIOCM_DTR|TIOCM_RTS);
}

static int cp210x_tiocmget(struct tty_struct *tty)
{
        struct usb_serial_port *port = tty->driver_data;
        u8 control;
        int result;

        result = cp210x_read_u8_reg(port, CP210X_GET_MDMSTS, &control);
        if (result)
                return result;

        result = ((control & CONTROL_DTR) ? TIOCM_DTR : 0)
                |((control & CONTROL_RTS) ? TIOCM_RTS : 0)
                |((control & CONTROL_CTS) ? TIOCM_CTS : 0)
                |((control & CONTROL_DSR) ? TIOCM_DSR : 0)
                |((control & CONTROL_RING)? TIOCM_RI  : 0)
                |((control & CONTROL_DCD) ? TIOCM_CD  : 0);

        dev_dbg(&port->dev, "%s - control = 0x%.2x\n", __func__, control);

        return result;
}

static void cp210x_break_ctl(struct tty_struct *tty, int break_state)
{
        struct usb_serial_port *port = tty->driver_data;
        u16 state;

        if (break_state == 0)
                state = BREAK_OFF;
        else
                state = BREAK_ON;
        dev_dbg(&port->dev, "%s - turning break %s\n", __func__,
                state == BREAK_OFF ? "off" : "on");
        cp210x_write_u16_reg(port, CP210X_SET_BREAK, state);
}

#ifdef CONFIG_GPIOLIB
static int cp210x_gpio_request(struct gpio_chip *gc, unsigned int offset)
{
        struct usb_serial *serial = gpiochip_get_data(gc);
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);

        if (priv->gpio_altfunc & BIT(offset))
                return -ENODEV;

        return 0;
}

static int cp210x_gpio_get(struct gpio_chip *gc, unsigned int gpio)
{
        struct usb_serial *serial = gpiochip_get_data(gc);
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);
        u8 req_type = REQTYPE_DEVICE_TO_HOST;
        int result;
        u8 buf;

        if (priv->partnum == CP210X_PARTNUM_CP2105)
                req_type = REQTYPE_INTERFACE_TO_HOST;

        result = usb_autopm_get_interface(serial->interface);
        if (result)
                return result;

        result = cp210x_read_vendor_block(serial, req_type,
                                          CP210X_READ_LATCH, &buf, sizeof(buf));
        usb_autopm_put_interface(serial->interface);
        if (result < 0)
                return result;

        return !!(buf & BIT(gpio));
}

static void cp210x_gpio_set(struct gpio_chip *gc, unsigned int gpio, int value)
{
        struct usb_serial *serial = gpiochip_get_data(gc);
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);
        struct cp210x_gpio_write buf;
        int result;

        if (value == 1)
                buf.state = BIT(gpio);
        else
                buf.state = 0;

        buf.mask = BIT(gpio);

        result = usb_autopm_get_interface(serial->interface);
        if (result)
                goto out;

        if (priv->partnum == CP210X_PARTNUM_CP2105) {
                result = cp210x_write_vendor_block(serial,
                                                   REQTYPE_HOST_TO_INTERFACE,
                                                   CP210X_WRITE_LATCH, &buf,
                                                   sizeof(buf));
        } else {
                u16 wIndex = buf.state << 8 | buf.mask;

                result = usb_control_msg(serial->dev,
                                         usb_sndctrlpipe(serial->dev, 0),
                                         CP210X_VENDOR_SPECIFIC,
                                         REQTYPE_HOST_TO_DEVICE,
                                         CP210X_WRITE_LATCH,
                                         wIndex,
                                         NULL, 0, USB_CTRL_SET_TIMEOUT);
        }

        usb_autopm_put_interface(serial->interface);
out:
        if (result < 0) {
                dev_err(&serial->interface->dev, "failed to set GPIO value: %d\n",
                                result);
        }
}

static int cp210x_gpio_direction_get(struct gpio_chip *gc, unsigned int gpio)
{
        struct usb_serial *serial = gpiochip_get_data(gc);
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);

        return priv->gpio_input & BIT(gpio);
}

static int cp210x_gpio_direction_input(struct gpio_chip *gc, unsigned int gpio)
{
        struct usb_serial *serial = gpiochip_get_data(gc);
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);

        if (priv->partnum == CP210X_PARTNUM_CP2105) {
                /* hardware does not support an input mode */
                return -ENOTSUPP;
        }

        /* push-pull pins cannot be changed to be inputs */
        if (priv->gpio_pushpull & BIT(gpio))
                return -EINVAL;

        /* make sure to release pin if it is being driven low */
        cp210x_gpio_set(gc, gpio, 1);

        priv->gpio_input |= BIT(gpio);

        return 0;
}

static int cp210x_gpio_direction_output(struct gpio_chip *gc, unsigned int gpio,
                                        int value)
{
        struct usb_serial *serial = gpiochip_get_data(gc);
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);

        priv->gpio_input &= ~BIT(gpio);
        cp210x_gpio_set(gc, gpio, value);

        return 0;
}

static int cp210x_gpio_set_config(struct gpio_chip *gc, unsigned int gpio,
                                  unsigned long config)
{
        struct usb_serial *serial = gpiochip_get_data(gc);
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);
        enum pin_config_param param = pinconf_to_config_param(config);

        /* Succeed only if in correct mode (this can't be set at runtime) */
        if ((param == PIN_CONFIG_DRIVE_PUSH_PULL) &&
            (priv->gpio_pushpull & BIT(gpio)))
                return 0;

        if ((param == PIN_CONFIG_DRIVE_OPEN_DRAIN) &&
            !(priv->gpio_pushpull & BIT(gpio)))
                return 0;

        return -ENOTSUPP;
}

/*
 * This function is for configuring GPIO using shared pins, where other signals
 * are made unavailable by configuring the use of GPIO. This is believed to be
 * only applicable to the cp2105 at this point, the other devices supported by
 * this driver that provide GPIO do so in a way that does not impact other
 * signals and are thus expected to have very different initialisation.
 */
static int cp2105_gpioconf_init(struct usb_serial *serial)
{
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);
        struct cp210x_pin_mode mode;
        struct cp210x_dual_port_config config;
        u8 intf_num = cp210x_interface_num(serial);
        u8 iface_config;
        int result;

        result = cp210x_read_vendor_block(serial, REQTYPE_DEVICE_TO_HOST,
                                          CP210X_GET_DEVICEMODE, &mode,
                                          sizeof(mode));
        if (result < 0)
                return result;

        result = cp210x_read_vendor_block(serial, REQTYPE_DEVICE_TO_HOST,
                                          CP210X_GET_PORTCONFIG, &config,
                                          sizeof(config));
        if (result < 0)
                return result;

        /*  2 banks of GPIO - One for the pins taken from each serial port */
        if (intf_num == 0) {
                if (mode.eci == CP210X_PIN_MODE_MODEM) {
                        /* mark all GPIOs of this interface as reserved */
                        priv->gpio_altfunc = 0xff;
                        return 0;
                }

                iface_config = config.eci_cfg;
                priv->gpio_pushpull = (u8)((le16_to_cpu(config.gpio_mode) &
                                                CP210X_ECI_GPIO_MODE_MASK) >>
                                                CP210X_ECI_GPIO_MODE_OFFSET);
                priv->gc.ngpio = 2;
        } else if (intf_num == 1) {
                if (mode.sci == CP210X_PIN_MODE_MODEM) {
                        /* mark all GPIOs of this interface as reserved */
                        priv->gpio_altfunc = 0xff;
                        return 0;
                }

                iface_config = config.sci_cfg;
                priv->gpio_pushpull = (u8)((le16_to_cpu(config.gpio_mode) &
                                                CP210X_SCI_GPIO_MODE_MASK) >>
                                                CP210X_SCI_GPIO_MODE_OFFSET);
                priv->gc.ngpio = 3;
        } else {
                return -ENODEV;
        }

        /* mark all pins which are not in GPIO mode */
        if (iface_config & CP2105_GPIO0_TXLED_MODE)     /* GPIO 0 */
                priv->gpio_altfunc |= BIT(0);
        if (iface_config & (CP2105_GPIO1_RXLED_MODE |   /* GPIO 1 */
                        CP2105_GPIO1_RS485_MODE))
                priv->gpio_altfunc |= BIT(1);

        /* driver implementation for CP2105 only supports outputs */
        priv->gpio_input = 0;

        return 0;
}

static int cp2104_gpioconf_init(struct usb_serial *serial)
{
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);
        struct cp210x_single_port_config config;
        u8 iface_config;
        u8 gpio_latch;
        int result;
        u8 i;

        result = cp210x_read_vendor_block(serial, REQTYPE_DEVICE_TO_HOST,
                                          CP210X_GET_PORTCONFIG, &config,
                                          sizeof(config));
        if (result < 0)
                return result;

        priv->gc.ngpio = 4;

        iface_config = config.device_cfg;
        priv->gpio_pushpull = (u8)((le16_to_cpu(config.gpio_mode) &
                                        CP210X_GPIO_MODE_MASK) >>
                                        CP210X_GPIO_MODE_OFFSET);
        gpio_latch = (u8)((le16_to_cpu(config.reset_state) &
                                        CP210X_GPIO_MODE_MASK) >>
                                        CP210X_GPIO_MODE_OFFSET);

        /* mark all pins which are not in GPIO mode */
        if (iface_config & CP2104_GPIO0_TXLED_MODE)     /* GPIO 0 */
                priv->gpio_altfunc |= BIT(0);
        if (iface_config & CP2104_GPIO1_RXLED_MODE)     /* GPIO 1 */
                priv->gpio_altfunc |= BIT(1);
        if (iface_config & CP2104_GPIO2_RS485_MODE)     /* GPIO 2 */
                priv->gpio_altfunc |= BIT(2);

        /*
         * Like CP2102N, CP2104 has also no strict input and output pin
         * modes.
         * Do the same input mode emulation as CP2102N.
         */
        for (i = 0; i < priv->gc.ngpio; ++i) {
                /*
                 * Set direction to "input" iff pin is open-drain and reset
                 * value is 1.
                 */
                if (!(priv->gpio_pushpull & BIT(i)) && (gpio_latch & BIT(i)))
                        priv->gpio_input |= BIT(i);
        }

        return 0;
}

static int cp2102n_gpioconf_init(struct usb_serial *serial)
{
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);
        const u16 config_size = 0x02a6;
        u8 gpio_rst_latch;
        u8 config_version;
        u8 gpio_pushpull;
        u8 *config_buf;
        u8 gpio_latch;
        u8 gpio_ctrl;
        int result;
        u8 i;

        /*
         * Retrieve device configuration from the device.
         * The array received contains all customization settings done at the
         * factory/manufacturer. Format of the array is documented at the
         * time of writing at:
         * https://www.silabs.com/community/interface/knowledge-base.entry.html/2017/03/31/cp2102n_setconfig-xsfa
         */
        config_buf = kmalloc(config_size, GFP_KERNEL);
        if (!config_buf)
                return -ENOMEM;

        result = cp210x_read_vendor_block(serial,
                                          REQTYPE_DEVICE_TO_HOST,
                                          CP210X_READ_2NCONFIG,
                                          config_buf,
                                          config_size);
        if (result < 0) {
                kfree(config_buf);
                return result;
        }

        config_version = config_buf[CP210X_2NCONFIG_CONFIG_VERSION_IDX];
        gpio_pushpull = config_buf[CP210X_2NCONFIG_GPIO_MODE_IDX];
        gpio_ctrl = config_buf[CP210X_2NCONFIG_GPIO_CONTROL_IDX];
        gpio_rst_latch = config_buf[CP210X_2NCONFIG_GPIO_RSTLATCH_IDX];

        kfree(config_buf);

        /* Make sure this is a config format we understand. */
        if (config_version != 0x01)
                return -ENOTSUPP;

        priv->gc.ngpio = 4;

        /*
         * Get default pin states after reset. Needed so we can determine
         * the direction of an open-drain pin.
         */
        gpio_latch = (gpio_rst_latch >> 3) & 0x0f;

        /* 0 indicates open-drain mode, 1 is push-pull */
        priv->gpio_pushpull = (gpio_pushpull >> 3) & 0x0f;

        /* 0 indicates GPIO mode, 1 is alternate function */
        priv->gpio_altfunc = (gpio_ctrl >> 2) & 0x0f;

        if (priv->partnum == CP210X_PARTNUM_CP2102N_QFN28) {
                /*
                 * For the QFN28 package, GPIO4-6 are controlled by
                 * the low three bits of the mode/latch fields.
                 * Contrary to the document linked above, the bits for
                 * the SUSPEND pins are elsewhere.  No alternate
                 * function is available for these pins.
                 */
                priv->gc.ngpio = 7;
                gpio_latch |= (gpio_rst_latch & 7) << 4;
                priv->gpio_pushpull |= (gpio_pushpull & 7) << 4;
        }

        /*
         * The CP2102N does not strictly has input and output pin modes,
         * it only knows open-drain and push-pull modes which is set at
         * factory. An open-drain pin can function both as an
         * input or an output. We emulate input mode for open-drain pins
         * by making sure they are not driven low, and we do not allow
         * push-pull pins to be set as an input.
         */
        for (i = 0; i < priv->gc.ngpio; ++i) {
                /*
                 * Set direction to "input" iff pin is open-drain and reset
                 * value is 1.
                 */
                if (!(priv->gpio_pushpull & BIT(i)) && (gpio_latch & BIT(i)))
                        priv->gpio_input |= BIT(i);
        }

        return 0;
}

static int cp210x_gpio_init(struct usb_serial *serial)
{
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);
        int result;

        switch (priv->partnum) {
        case CP210X_PARTNUM_CP2104:
                result = cp2104_gpioconf_init(serial);
                break;
        case CP210X_PARTNUM_CP2105:
                result = cp2105_gpioconf_init(serial);
                break;
        case CP210X_PARTNUM_CP2102N_QFN28:
        case CP210X_PARTNUM_CP2102N_QFN24:
        case CP210X_PARTNUM_CP2102N_QFN20:
                result = cp2102n_gpioconf_init(serial);
                break;
        default:
                return 0;
        }

        if (result < 0)
                return result;

        priv->gc.label = "cp210x";
        priv->gc.request = cp210x_gpio_request;
        priv->gc.get_direction = cp210x_gpio_direction_get;
        priv->gc.direction_input = cp210x_gpio_direction_input;
        priv->gc.direction_output = cp210x_gpio_direction_output;
        priv->gc.get = cp210x_gpio_get;
        priv->gc.set = cp210x_gpio_set;
        priv->gc.set_config = cp210x_gpio_set_config;
        priv->gc.owner = THIS_MODULE;
        priv->gc.parent = &serial->interface->dev;
        priv->gc.base = -1;
        priv->gc.can_sleep = true;

        result = gpiochip_add_data(&priv->gc, serial);
        if (!result)
                priv->gpio_registered = true;

        return result;
}

static void cp210x_gpio_remove(struct usb_serial *serial)
{
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);

        if (priv->gpio_registered) {
                gpiochip_remove(&priv->gc);
                priv->gpio_registered = false;
        }
}

#else

static int cp210x_gpio_init(struct usb_serial *serial)
{
        return 0;
}

static void cp210x_gpio_remove(struct usb_serial *serial)
{
        /* Nothing to do */
}

#endif

static int cp210x_port_probe(struct usb_serial_port *port)
{
        struct usb_serial *serial = port->serial;
        struct cp210x_port_private *port_priv;
        int ret;

        port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL);
        if (!port_priv)
                return -ENOMEM;

        port_priv->bInterfaceNumber = cp210x_interface_num(serial);

        usb_set_serial_port_data(port, port_priv);

        ret = cp210x_detect_swapped_line_ctl(port);
        if (ret) {
                kfree(port_priv);
                return ret;
        }

        return 0;
}

static int cp210x_port_remove(struct usb_serial_port *port)
{
        struct cp210x_port_private *port_priv;

        port_priv = usb_get_serial_port_data(port);
        kfree(port_priv);

        return 0;
}

static void cp210x_init_max_speed(struct usb_serial *serial)
{
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);
        bool use_actual_rate = false;
        speed_t min = 300;
        speed_t max;

        switch (priv->partnum) {
        case CP210X_PARTNUM_CP2101:
                max = 921600;
                break;
        case CP210X_PARTNUM_CP2102:
        case CP210X_PARTNUM_CP2103:
                max = 1000000;
                break;
        case CP210X_PARTNUM_CP2104:
                use_actual_rate = true;
                max = 2000000;
                break;
        case CP210X_PARTNUM_CP2108:
                max = 2000000;
                break;
        case CP210X_PARTNUM_CP2105:
                if (cp210x_interface_num(serial) == 0) {
                        use_actual_rate = true;
                        max = 2000000;  /* ECI */
                } else {
                        min = 2400;
                        max = 921600;   /* SCI */
                }
                break;
        case CP210X_PARTNUM_CP2102N_QFN28:
        case CP210X_PARTNUM_CP2102N_QFN24:
        case CP210X_PARTNUM_CP2102N_QFN20:
                use_actual_rate = true;
                max = 3000000;
                break;
        default:
                max = 2000000;
                break;
        }

        priv->min_speed = min;
        priv->max_speed = max;
        priv->use_actual_rate = use_actual_rate;
}

static int cp210x_attach(struct usb_serial *serial)
{
        int result;
        struct cp210x_serial_private *priv;

        priv = kzalloc(sizeof(*priv), GFP_KERNEL);
        if (!priv)
                return -ENOMEM;

        result = cp210x_read_vendor_block(serial, REQTYPE_DEVICE_TO_HOST,
                                          CP210X_GET_PARTNUM, &priv->partnum,
                                          sizeof(priv->partnum));
        if (result < 0) {
                dev_warn(&serial->interface->dev,
                         "querying part number failed\n");
                priv->partnum = CP210X_PARTNUM_UNKNOWN;
        }

        usb_set_serial_data(serial, priv);

        cp210x_init_max_speed(serial);

        result = cp210x_gpio_init(serial);
        if (result < 0) {
                dev_err(&serial->interface->dev, "GPIO initialisation failed: %d\n",
                                result);
        }

        return 0;
}

static void cp210x_disconnect(struct usb_serial *serial)
{
        cp210x_gpio_remove(serial);
}

static void cp210x_release(struct usb_serial *serial)
{
        struct cp210x_serial_private *priv = usb_get_serial_data(serial);

        cp210x_gpio_remove(serial);

        kfree(priv);
}

module_usb_serial_driver(serial_drivers, id_table);

MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL v2");