// SPDX-License-Identifier: GPL-2.0+
/*
 * Edgeport USB Serial Converter driver
 *
 * Copyright (C) 2000-2002 Inside Out Networks, All rights reserved.
 * Copyright (C) 2001-2002 Greg Kroah-Hartman <greg@kroah.com>
 *
 * Supports the following devices:
 *      EP/1 EP/2 EP/4 EP/21 EP/22 EP/221 EP/42 EP/421 WATCHPORT
 *
 * For questions or problems with this driver, contact Inside Out
 * Networks technical support, or Peter Berger <pberger@brimson.com>,
 * or Al Borchers <alborchers@steinerpoint.com>.
 */

#include <linux/kernel.h>
#include <linux/jiffies.h>
#include <linux/errno.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_driver.h>
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/spinlock.h>
#include <linux/mutex.h>
#include <linux/serial.h>
#include <linux/swab.h>
#include <linux/kfifo.h>
#include <linux/ioctl.h>
#include <linux/firmware.h>
#include <linux/uaccess.h>
#include <linux/usb.h>
#include <linux/usb/serial.h>

#include "io_16654.h"
#include "io_usbvend.h"
#include "io_ti.h"

#define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com> and David Iacovelli"
#define DRIVER_DESC "Edgeport USB Serial Driver"

#define EPROM_PAGE_SIZE         64


/* different hardware types */
#define HARDWARE_TYPE_930       0
#define HARDWARE_TYPE_TIUMP     1

/* IOCTL_PRIVATE_TI_GET_MODE Definitions */
#define TI_MODE_CONFIGURING     0   /* Device has not entered start device */
#define TI_MODE_BOOT            1   /* Staying in boot mode                */
#define TI_MODE_DOWNLOAD        2   /* Made it to download mode            */
#define TI_MODE_TRANSITIONING   3   /*
                                     * Currently in boot mode but
                                     * transitioning to download mode
                                     */

/* read urb state */
#define EDGE_READ_URB_RUNNING   0
#define EDGE_READ_URB_STOPPING  1
#define EDGE_READ_URB_STOPPED   2

#define EDGE_CLOSING_WAIT       4000    /* in .01 sec */


/* Product information read from the Edgeport */
struct product_info {
        int     TiMode;                 /* Current TI Mode  */
        __u8    hardware_type;          /* Type of hardware */
} __attribute__((packed));

/*
 * Edgeport firmware header
 *
 * "build_number" has been set to 0 in all three of the images I have
 * seen, and Digi Tech Support suggests that it is safe to ignore it.
 *
 * "length" is the number of bytes of actual data following the header.
 *
 * "checksum" is the low order byte resulting from adding the values of
 * all the data bytes.
 */
struct edgeport_fw_hdr {
        u8 major_version;
        u8 minor_version;
        __le16 build_number;
        __le16 length;
        u8 checksum;
} __packed;

struct edgeport_port {
        __u16 uart_base;
        __u16 dma_address;
        __u8 shadow_msr;
        __u8 shadow_mcr;
        __u8 shadow_lsr;
        __u8 lsr_mask;
        __u32 ump_read_timeout;         /*
                                         * Number of milliseconds the UMP will
                                         * wait without data before completing
                                         * a read short
                                         */
        int baud_rate;
        int close_pending;
        int lsr_event;

        struct edgeport_serial  *edge_serial;
        struct usb_serial_port  *port;
        __u8 bUartMode;         /* Port type, 0: RS232, etc. */
        spinlock_t ep_lock;
        int ep_read_urb_state;
        int ep_write_urb_in_use;
};

struct edgeport_serial {
        struct product_info product_info;
        u8 TI_I2C_Type;                 /* Type of I2C in UMP */
        u8 TiReadI2C;                   /*
                                         * Set to TRUE if we have read the
                                         * I2c in Boot Mode
                                         */
        struct mutex es_lock;
        int num_ports_open;
        struct usb_serial *serial;
        struct delayed_work heartbeat_work;
        int fw_version;
        bool use_heartbeat;
};


/* Devices that this driver supports */
static const struct usb_device_id edgeport_1port_id_table[] = {
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_1) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROXIMITY) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOTION) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOISTURE) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_TEMPERATURE) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_HUMIDITY) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_POWER) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_LIGHT) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_RADIATION) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_DISTANCE) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_ACCELERATION) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROX_DIST) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_HP4CD) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_PCI) },
        { }
};

static const struct usb_device_id edgeport_2port_id_table[] = {
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2C) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2I) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_421) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_42) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4I) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22I) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_221C) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22C) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21C) },
        /* The 4, 8 and 16 port devices show up as multiple 2 port devices */
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4S) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8S) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416B) },
        { }
};

/* Devices that this driver supports */
static const struct usb_device_id id_table_combined[] = {
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_1) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROXIMITY) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOTION) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOISTURE) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_TEMPERATURE) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_HUMIDITY) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_POWER) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_LIGHT) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_RADIATION) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_DISTANCE) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_ACCELERATION) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROX_DIST) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_HP4CD) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_PCI) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2C) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2I) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_421) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_42) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4I) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22I) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_221C) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22C) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21C) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4S) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8S) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416) },
        { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416B) },
        { }
};

MODULE_DEVICE_TABLE(usb, id_table_combined);

static int closing_wait = EDGE_CLOSING_WAIT;
static bool ignore_cpu_rev;
static int default_uart_mode;           /* RS232 */

static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data,
                int length);

static void stop_read(struct edgeport_port *edge_port);
static int restart_read(struct edgeport_port *edge_port);

static void edge_set_termios(struct tty_struct *tty,
                struct usb_serial_port *port, struct ktermios *old_termios);
static void edge_send(struct usb_serial_port *port, struct tty_struct *tty);

static int do_download_mode(struct edgeport_serial *serial,
                const struct firmware *fw);
static int do_boot_mode(struct edgeport_serial *serial,
                const struct firmware *fw);

/* sysfs attributes */
static int edge_create_sysfs_attrs(struct usb_serial_port *port);
static int edge_remove_sysfs_attrs(struct usb_serial_port *port);

/*
 * Some release of Edgeport firmware "down3.bin" after version 4.80
 * introduced code to automatically disconnect idle devices on some
 * Edgeport models after periods of inactivity, typically ~60 seconds.
 * This occurs without regard to whether ports on the device are open
 * or not.  Digi International Tech Support suggested:
 *
 * 1.  Adding driver "heartbeat" code to reset the firmware timer by
 *     requesting a descriptor record every 15 seconds, which should be
 *     effective with newer firmware versions that require it, and benign
 *     with older versions that do not. In practice 40 seconds seems often
 *     enough.
 * 2.  The heartbeat code is currently required only on Edgeport/416 models.
 */
#define FW_HEARTBEAT_VERSION_CUTOFF ((4 << 8) + 80)
#define FW_HEARTBEAT_SECS 40

/* Timeouts in msecs: firmware downloads take longer */
#define TI_VSEND_TIMEOUT_DEFAULT 1000
#define TI_VSEND_TIMEOUT_FW_DOWNLOAD 10000

static int ti_vread_sync(struct usb_device *dev, __u8 request,
                                __u16 value, __u16 index, u8 *data, int size)
{
        int status;

        status = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), request,
                        (USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN),
                        value, index, data, size, 1000);
        if (status < 0)
                return status;
        if (status != size) {
                dev_dbg(&dev->dev, "%s - wanted to write %d, but only wrote %d\n",
                        __func__, size, status);
                return -ECOMM;
        }
        return 0;
}

static int ti_vsend_sync(struct usb_device *dev, u8 request, u16 value,
                u16 index, u8 *data, int size, int timeout)
{
        int status;

        status = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), request,
                        (USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT),
                        value, index, data, size, timeout);
        if (status < 0)
                return status;
        if (status != size) {
                dev_dbg(&dev->dev, "%s - wanted to write %d, but only wrote %d\n",
                        __func__, size, status);
                return -ECOMM;
        }
        return 0;
}

static int send_cmd(struct usb_device *dev, __u8 command,
                                __u8 moduleid, __u16 value, u8 *data,
                                int size)
{
        return ti_vsend_sync(dev, command, value, moduleid, data, size,
                        TI_VSEND_TIMEOUT_DEFAULT);
}

/* clear tx/rx buffers and fifo in TI UMP */
static int purge_port(struct usb_serial_port *port, __u16 mask)
{
        int port_number = port->port_number;

        dev_dbg(&port->dev, "%s - port %d, mask %x\n", __func__, port_number, mask);

        return send_cmd(port->serial->dev,
                                        UMPC_PURGE_PORT,
                                        (__u8)(UMPM_UART1_PORT + port_number),
                                        mask,
                                        NULL,
                                        0);
}

/**
 * read_download_mem - Read edgeport memory from TI chip
 * @dev: usb device pointer
 * @start_address: Device CPU address at which to read
 * @length: Length of above data
 * @address_type: Can read both XDATA and I2C
 * @buffer: pointer to input data buffer
 */
static int read_download_mem(struct usb_device *dev, int start_address,
                                int length, __u8 address_type, __u8 *buffer)
{
        int status = 0;
        __u8 read_length;
        u16 be_start_address;

        dev_dbg(&dev->dev, "%s - @ %x for %d\n", __func__, start_address, length);

        /*
         * Read in blocks of 64 bytes
         * (TI firmware can't handle more than 64 byte reads)
         */
        while (length) {
                if (length > 64)
                        read_length = 64;
                else
                        read_length = (__u8)length;

                if (read_length > 1) {
                        dev_dbg(&dev->dev, "%s - @ %x for %d\n", __func__, start_address, read_length);
                }
                /*
                 * NOTE: Must use swab as wIndex is sent in little-endian
                 *       byte order regardless of host byte order.
                 */
                be_start_address = swab16((u16)start_address);
                status = ti_vread_sync(dev, UMPC_MEMORY_READ,
                                        (__u16)address_type,
                                        be_start_address,
                                        buffer, read_length);

                if (status) {
                        dev_dbg(&dev->dev, "%s - ERROR %x\n", __func__, status);
                        return status;
                }

                if (read_length > 1)
                        usb_serial_debug_data(&dev->dev, __func__, read_length, buffer);

                /* Update pointers/length */
                start_address += read_length;
                buffer += read_length;
                length -= read_length;
        }

        return status;
}

static int read_ram(struct usb_device *dev, int start_address,
                                                int length, __u8 *buffer)
{
        return read_download_mem(dev, start_address, length,
                                        DTK_ADDR_SPACE_XDATA, buffer);
}

/* Read edgeport memory to a given block */
static int read_boot_mem(struct edgeport_serial *serial,
                                int start_address, int length, __u8 *buffer)
{
        int status = 0;
        int i;

        for (i = 0; i < length; i++) {
                status = ti_vread_sync(serial->serial->dev,
                                UMPC_MEMORY_READ, serial->TI_I2C_Type,
                                (__u16)(start_address+i), &buffer[i], 0x01);
                if (status) {
                        dev_dbg(&serial->serial->dev->dev, "%s - ERROR %x\n", __func__, status);
                        return status;
                }
        }

        dev_dbg(&serial->serial->dev->dev, "%s - start_address = %x, length = %d\n",
                __func__, start_address, length);
        usb_serial_debug_data(&serial->serial->dev->dev, __func__, length, buffer);

        serial->TiReadI2C = 1;

        return status;
}

/* Write given block to TI EPROM memory */
static int write_boot_mem(struct edgeport_serial *serial,
                                int start_address, int length, __u8 *buffer)
{
        int status = 0;
        int i;
        u8 *temp;

        /* Must do a read before write */
        if (!serial->TiReadI2C) {
                temp = kmalloc(1, GFP_KERNEL);
                if (!temp)
                        return -ENOMEM;

                status = read_boot_mem(serial, 0, 1, temp);
                kfree(temp);
                if (status)
                        return status;
        }

        for (i = 0; i < length; ++i) {
                status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE,
                                buffer[i], (u16)(i + start_address), NULL,
                                0, TI_VSEND_TIMEOUT_DEFAULT);
                if (status)
                        return status;
        }

        dev_dbg(&serial->serial->dev->dev, "%s - start_sddr = %x, length = %d\n", __func__, start_address, length);
        usb_serial_debug_data(&serial->serial->dev->dev, __func__, length, buffer);

        return status;
}

/* Write edgeport I2C memory to TI chip */
static int write_i2c_mem(struct edgeport_serial *serial,
                int start_address, int length, __u8 address_type, __u8 *buffer)
{
        struct device *dev = &serial->serial->dev->dev;
        int status = 0;
        int write_length;
        u16 be_start_address;

        /* We can only send a maximum of 1 aligned byte page at a time */

        /* calculate the number of bytes left in the first page */
        write_length = EPROM_PAGE_SIZE -
                                (start_address & (EPROM_PAGE_SIZE - 1));

        if (write_length > length)
                write_length = length;

        dev_dbg(dev, "%s - BytesInFirstPage Addr = %x, length = %d\n",
                __func__, start_address, write_length);
        usb_serial_debug_data(dev, __func__, write_length, buffer);

        /*
         * Write first page.
         *
         * NOTE: Must use swab as wIndex is sent in little-endian byte order
         *       regardless of host byte order.
         */
        be_start_address = swab16((u16)start_address);
        status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE,
                                (u16)address_type, be_start_address,
                                buffer, write_length, TI_VSEND_TIMEOUT_DEFAULT);
        if (status) {
                dev_dbg(dev, "%s - ERROR %d\n", __func__, status);
                return status;
        }

        length          -= write_length;
        start_address   += write_length;
        buffer          += write_length;

        /*
         * We should be aligned now -- can write max page size bytes at a
         * time.
         */
        while (length) {
                if (length > EPROM_PAGE_SIZE)
                        write_length = EPROM_PAGE_SIZE;
                else
                        write_length = length;

                dev_dbg(dev, "%s - Page Write Addr = %x, length = %d\n",
                        __func__, start_address, write_length);
                usb_serial_debug_data(dev, __func__, write_length, buffer);

                /*
                 * Write next page.
                 *
                 * NOTE: Must use swab as wIndex is sent in little-endian byte
                 *       order regardless of host byte order.
                 */
                be_start_address = swab16((u16)start_address);
                status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE,
                                (u16)address_type, be_start_address, buffer,
                                write_length, TI_VSEND_TIMEOUT_DEFAULT);
                if (status) {
                        dev_err(dev, "%s - ERROR %d\n", __func__, status);
                        return status;
                }

                length          -= write_length;
                start_address   += write_length;
                buffer          += write_length;
        }
        return status;
}

/*
 * Examine the UMP DMA registers and LSR
 *
 * Check the MSBit of the X and Y DMA byte count registers.
 * A zero in this bit indicates that the TX DMA buffers are empty
 * then check the TX Empty bit in the UART.
 */
static int tx_active(struct edgeport_port *port)
{
        int status;
        struct out_endpoint_desc_block *oedb;
        __u8 *lsr;
        int bytes_left = 0;

        oedb = kmalloc(sizeof(*oedb), GFP_KERNEL);
        if (!oedb)
                return -ENOMEM;

        /*
         * Sigh, that's right, just one byte, as not all platforms can
         * do DMA from stack
         */
        lsr = kmalloc(1, GFP_KERNEL);
        if (!lsr) {
                kfree(oedb);
                return -ENOMEM;
        }
        /* Read the DMA Count Registers */
        status = read_ram(port->port->serial->dev, port->dma_address,
                                                sizeof(*oedb), (void *)oedb);
        if (status)
                goto exit_is_tx_active;

        dev_dbg(&port->port->dev, "%s - XByteCount    0x%X\n", __func__, oedb->XByteCount);

        /* and the LSR */
        status = read_ram(port->port->serial->dev,
                        port->uart_base + UMPMEM_OFFS_UART_LSR, 1, lsr);

        if (status)
                goto exit_is_tx_active;
        dev_dbg(&port->port->dev, "%s - LSR = 0x%X\n", __func__, *lsr);

        /* If either buffer has data or we are transmitting then return TRUE */
        if ((oedb->XByteCount & 0x80) != 0)
                bytes_left += 64;

        if ((*lsr & UMP_UART_LSR_TX_MASK) == 0)
                bytes_left += 1;

        /* We return Not Active if we get any kind of error */
exit_is_tx_active:
        dev_dbg(&port->port->dev, "%s - return %d\n", __func__, bytes_left);

        kfree(lsr);
        kfree(oedb);
        return bytes_left;
}

static int choose_config(struct usb_device *dev)
{
        /*
         * There may be multiple configurations on this device, in which case
         * we would need to read and parse all of them to find out which one
         * we want. However, we just support one config at this point,
         * configuration # 1, which is Config Descriptor 0.
         */

        dev_dbg(&dev->dev, "%s - Number of Interfaces = %d\n",
                __func__, dev->config->desc.bNumInterfaces);
        dev_dbg(&dev->dev, "%s - MAX Power            = %d\n",
                __func__, dev->config->desc.bMaxPower * 2);

        if (dev->config->desc.bNumInterfaces != 1) {
                dev_err(&dev->dev, "%s - bNumInterfaces is not 1, ERROR!\n", __func__);
                return -ENODEV;
        }

        return 0;
}

static int read_rom(struct edgeport_serial *serial,
                                int start_address, int length, __u8 *buffer)
{
        int status;

        if (serial->product_info.TiMode == TI_MODE_DOWNLOAD) {
                status = read_download_mem(serial->serial->dev,
                                               start_address,
                                               length,
                                               serial->TI_I2C_Type,
                                               buffer);
        } else {
                status = read_boot_mem(serial, start_address, length,
                                                                buffer);
        }
        return status;
}

static int write_rom(struct edgeport_serial *serial, int start_address,
                                                int length, __u8 *buffer)
{
        if (serial->product_info.TiMode == TI_MODE_BOOT)
                return write_boot_mem(serial, start_address, length,
                                                                buffer);

        if (serial->product_info.TiMode == TI_MODE_DOWNLOAD)
                return write_i2c_mem(serial, start_address, length,
                                                serial->TI_I2C_Type, buffer);
        return -EINVAL;
}

/* Read a descriptor header from I2C based on type */
static int get_descriptor_addr(struct edgeport_serial *serial,
                                int desc_type, struct ti_i2c_desc *rom_desc)
{
        int start_address;
        int status;

        /* Search for requested descriptor in I2C */
        start_address = 2;
        do {
                status = read_rom(serial,
                                   start_address,
                                   sizeof(struct ti_i2c_desc),
                                   (__u8 *)rom_desc);
                if (status)
                        return 0;

                if (rom_desc->Type == desc_type)
                        return start_address;

                start_address = start_address + sizeof(struct ti_i2c_desc) +
                                                le16_to_cpu(rom_desc->Size);

        } while ((start_address < TI_MAX_I2C_SIZE) && rom_desc->Type);

        return 0;
}

/* Validate descriptor checksum */
static int valid_csum(struct ti_i2c_desc *rom_desc, __u8 *buffer)
{
        __u16 i;
        __u8 cs = 0;

        for (i = 0; i < le16_to_cpu(rom_desc->Size); i++)
                cs = (__u8)(cs + buffer[i]);

        if (cs != rom_desc->CheckSum) {
                pr_debug("%s - Mismatch %x - %x", __func__, rom_desc->CheckSum, cs);
                return -EINVAL;
        }
        return 0;
}

/* Make sure that the I2C image is good */
static int check_i2c_image(struct edgeport_serial *serial)
{
        struct device *dev = &serial->serial->dev->dev;
        int status = 0;
        struct ti_i2c_desc *rom_desc;
        int start_address = 2;
        __u8 *buffer;
        __u16 ttype;

        rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL);
        if (!rom_desc)
                return -ENOMEM;

        buffer = kmalloc(TI_MAX_I2C_SIZE, GFP_KERNEL);
        if (!buffer) {
                kfree(rom_desc);
                return -ENOMEM;
        }

        /* Read the first byte (Signature0) must be 0x52 or 0x10 */
        status = read_rom(serial, 0, 1, buffer);
        if (status)
                goto out;

        if (*buffer != UMP5152 && *buffer != UMP3410) {
                dev_err(dev, "%s - invalid buffer signature\n", __func__);
                status = -ENODEV;
                goto out;
        }

        do {
                /* Validate the I2C */
                status = read_rom(serial,
                                start_address,
                                sizeof(struct ti_i2c_desc),
                                (__u8 *)rom_desc);
                if (status)
                        break;

                if ((start_address + sizeof(struct ti_i2c_desc) +
                        le16_to_cpu(rom_desc->Size)) > TI_MAX_I2C_SIZE) {
                        status = -ENODEV;
                        dev_dbg(dev, "%s - structure too big, erroring out.\n", __func__);
                        break;
                }

                dev_dbg(dev, "%s Type = 0x%x\n", __func__, rom_desc->Type);

                /* Skip type 2 record */
                ttype = rom_desc->Type & 0x0f;
                if (ttype != I2C_DESC_TYPE_FIRMWARE_BASIC
                        && ttype != I2C_DESC_TYPE_FIRMWARE_AUTO) {
                        /* Read the descriptor data */
                        status = read_rom(serial, start_address +
                                                sizeof(struct ti_i2c_desc),
                                                le16_to_cpu(rom_desc->Size),
                                                buffer);
                        if (status)
                                break;

                        status = valid_csum(rom_desc, buffer);
                        if (status)
                                break;
                }
                start_address = start_address + sizeof(struct ti_i2c_desc) +
                                                le16_to_cpu(rom_desc->Size);

        } while ((rom_desc->Type != I2C_DESC_TYPE_ION) &&
                                (start_address < TI_MAX_I2C_SIZE));

        if ((rom_desc->Type != I2C_DESC_TYPE_ION) ||
                                (start_address > TI_MAX_I2C_SIZE))
                status = -ENODEV;

out:
        kfree(buffer);
        kfree(rom_desc);
        return status;
}

static int get_manuf_info(struct edgeport_serial *serial, __u8 *buffer)
{
        int status;
        int start_address;
        struct ti_i2c_desc *rom_desc;
        struct edge_ti_manuf_descriptor *desc;
        struct device *dev = &serial->serial->dev->dev;

        rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL);
        if (!rom_desc)
                return -ENOMEM;

        start_address = get_descriptor_addr(serial, I2C_DESC_TYPE_ION,
                                                                rom_desc);

        if (!start_address) {
                dev_dbg(dev, "%s - Edge Descriptor not found in I2C\n", __func__);
                status = -ENODEV;
                goto exit;
        }

        /* Read the descriptor data */
        status = read_rom(serial, start_address+sizeof(struct ti_i2c_desc),
                                        le16_to_cpu(rom_desc->Size), buffer);
        if (status)
                goto exit;

        status = valid_csum(rom_desc, buffer);

        desc = (struct edge_ti_manuf_descriptor *)buffer;
        dev_dbg(dev, "%s - IonConfig      0x%x\n", __func__, desc->IonConfig);
        dev_dbg(dev, "%s - Version          %d\n", __func__, desc->Version);
        dev_dbg(dev, "%s - Cpu/Board      0x%x\n", __func__, desc->CpuRev_BoardRev);
        dev_dbg(dev, "%s - NumPorts         %d\n", __func__, desc->NumPorts);
        dev_dbg(dev, "%s - NumVirtualPorts  %d\n", __func__, desc->NumVirtualPorts);
        dev_dbg(dev, "%s - TotalPorts       %d\n", __func__, desc->TotalPorts);

exit:
        kfree(rom_desc);
        return status;
}

/* Build firmware header used for firmware update */
static int build_i2c_fw_hdr(u8 *header, const struct firmware *fw)
{
        __u8 *buffer;
        int buffer_size;
        int i;
        __u8 cs = 0;
        struct ti_i2c_desc *i2c_header;
        struct ti_i2c_image_header *img_header;
        struct ti_i2c_firmware_rec *firmware_rec;
        struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data;

        /*
         * In order to update the I2C firmware we must change the type 2 record
         * to type 0xF2.  This will force the UMP to come up in Boot Mode.
         * Then while in boot mode, the driver will download the latest
         * firmware (padded to 15.5k) into the UMP ram.  And finally when the
         * device comes back up in download mode the driver will cause the new
         * firmware to be copied from the UMP Ram to I2C and the firmware will
         * update the record type from 0xf2 to 0x02.
         */

        /*
         * Allocate a 15.5k buffer + 2 bytes for version number (Firmware
         * Record)
         */
        buffer_size = (((1024 * 16) - 512 ) +
                        sizeof(struct ti_i2c_firmware_rec));

        buffer = kmalloc(buffer_size, GFP_KERNEL);
        if (!buffer)
                return -ENOMEM;

        /* Set entire image of 0xffs */
        memset(buffer, 0xff, buffer_size);

        /* Copy version number into firmware record */
        firmware_rec = (struct ti_i2c_firmware_rec *)buffer;

        firmware_rec->Ver_Major = fw_hdr->major_version;
        firmware_rec->Ver_Minor = fw_hdr->minor_version;

        /* Pointer to fw_down memory image */
        img_header = (struct ti_i2c_image_header *)&fw->data[4];

        memcpy(buffer + sizeof(struct ti_i2c_firmware_rec),
                &fw->data[4 + sizeof(struct ti_i2c_image_header)],
                le16_to_cpu(img_header->Length));

        for (i=0; i < buffer_size; i++) {
                cs = (__u8)(cs + buffer[i]);
        }

        kfree(buffer);

        /* Build new header */
        i2c_header =  (struct ti_i2c_desc *)header;
        firmware_rec =  (struct ti_i2c_firmware_rec*)i2c_header->Data;

        i2c_header->Type        = I2C_DESC_TYPE_FIRMWARE_BLANK;
        i2c_header->Size        = cpu_to_le16(buffer_size);
        i2c_header->CheckSum    = cs;
        firmware_rec->Ver_Major = fw_hdr->major_version;
        firmware_rec->Ver_Minor = fw_hdr->minor_version;

        return 0;
}

/* Try to figure out what type of I2c we have */
static int i2c_type_bootmode(struct edgeport_serial *serial)
{
        struct device *dev = &serial->serial->dev->dev;
        int status;
        u8 *data;

        data = kmalloc(1, GFP_KERNEL);
        if (!data)
                return -ENOMEM;

        /* Try to read type 2 */
        status = ti_vread_sync(serial->serial->dev, UMPC_MEMORY_READ,
                                DTK_ADDR_SPACE_I2C_TYPE_II, 0, data, 0x01);
        if (status)
                dev_dbg(dev, "%s - read 2 status error = %d\n", __func__, status);
        else
                dev_dbg(dev, "%s - read 2 data = 0x%x\n", __func__, *data);
        if ((!status) && (*data == UMP5152 || *data == UMP3410)) {
                dev_dbg(dev, "%s - ROM_TYPE_II\n", __func__);
                serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;
                goto out;
        }

        /* Try to read type 3 */
        status = ti_vread_sync(serial->serial->dev, UMPC_MEMORY_READ,
                                DTK_ADDR_SPACE_I2C_TYPE_III, 0, data, 0x01);
        if (status)
                dev_dbg(dev, "%s - read 3 status error = %d\n", __func__, status);
        else
                dev_dbg(dev, "%s - read 2 data = 0x%x\n", __func__, *data);
        if ((!status) && (*data == UMP5152 || *data == UMP3410)) {
                dev_dbg(dev, "%s - ROM_TYPE_III\n", __func__);
                serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_III;
                goto out;
        }

        dev_dbg(dev, "%s - Unknown\n", __func__);
        serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;
        status = -ENODEV;
out:
        kfree(data);
        return status;
}

static int bulk_xfer(struct usb_serial *serial, void *buffer,
                                                int length, int *num_sent)
{
        int status;

        status = usb_bulk_msg(serial->dev,
                        usb_sndbulkpipe(serial->dev,
                                serial->port[0]->bulk_out_endpointAddress),
                        buffer, length, num_sent, 1000);
        return status;
}

/* Download given firmware image to the device (IN BOOT MODE) */
static int download_code(struct edgeport_serial *serial, __u8 *image,
                                                        int image_length)
{
        int status = 0;
        int pos;
        int transfer;
        int done;

        /* Transfer firmware image */
        for (pos = 0; pos < image_length; ) {
                /* Read the next buffer from file */
                transfer = image_length - pos;
                if (transfer > EDGE_FW_BULK_MAX_PACKET_SIZE)
                        transfer = EDGE_FW_BULK_MAX_PACKET_SIZE;

                /* Transfer data */
                status = bulk_xfer(serial->serial, &image[pos],
                                                        transfer, &done);
                if (status)
                        break;
                /* Advance buffer pointer */
                pos += done;
        }

        return status;
}

/* FIXME!!! */
static int config_boot_dev(struct usb_device *dev)
{
        return 0;
}

static int ti_cpu_rev(struct edge_ti_manuf_descriptor *desc)
{
        return TI_GET_CPU_REVISION(desc->CpuRev_BoardRev);
}

static int check_fw_sanity(struct edgeport_serial *serial,
                const struct firmware *fw)
{
        u16 length_total;
        u8 checksum = 0;
        int pos;
        struct device *dev = &serial->serial->interface->dev;
        struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data;

        if (fw->size < sizeof(struct edgeport_fw_hdr)) {
                dev_err(dev, "incomplete fw header\n");
                return -EINVAL;
        }

        length_total = le16_to_cpu(fw_hdr->length) +
                        sizeof(struct edgeport_fw_hdr);

        if (fw->size != length_total) {
                dev_err(dev, "bad fw size (expected: %u, got: %zu)\n",
                                length_total, fw->size);
                return -EINVAL;
        }

        for (pos = sizeof(struct edgeport_fw_hdr); pos < fw->size; ++pos)
                checksum += fw->data[pos];

        if (checksum != fw_hdr->checksum) {
                dev_err(dev, "bad fw checksum (expected: 0x%x, got: 0x%x)\n",
                                fw_hdr->checksum, checksum);
                return -EINVAL;
        }

        return 0;
}

/*
 * DownloadTIFirmware - Download run-time operating firmware to the TI5052
 *
 * This routine downloads the main operating code into the TI5052, using the
 * boot code already burned into E2PROM or ROM.

 */
static int download_fw(struct edgeport_serial *serial)
{
        struct device *dev = &serial->serial->interface->dev;
        int status = 0;
        struct usb_interface_descriptor *interface;
        const struct firmware *fw;
        const char *fw_name = "edgeport/down3.bin";
        struct edgeport_fw_hdr *fw_hdr;

        status = request_firmware(&fw, fw_name, dev);
        if (status) {
                dev_err(dev, "Failed to load image \"%s\" err %d\n",
                                fw_name, status);
                return status;
        }

        if (check_fw_sanity(serial, fw)) {
                status = -EINVAL;
                goto out;
        }

        fw_hdr = (struct edgeport_fw_hdr *)fw->data;

        /* If on-board version is newer, "fw_version" will be updated later. */
        serial->fw_version = (fw_hdr->major_version << 8) +
                        fw_hdr->minor_version;

        /*
         * This routine is entered by both the BOOT mode and the Download mode
         * We can determine which code is running by the reading the config
         * descriptor and if we have only one bulk pipe it is in boot mode
         */
        serial->product_info.hardware_type = HARDWARE_TYPE_TIUMP;

        /* Default to type 2 i2c */
        serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;

        status = choose_config(serial->serial->dev);
        if (status)
                goto out;

        interface = &serial->serial->interface->cur_altsetting->desc;
        if (!interface) {
                dev_err(dev, "%s - no interface set, error!\n", __func__);
                status = -ENODEV;
                goto out;
        }

        /*
         * Setup initial mode -- the default mode 0 is TI_MODE_CONFIGURING
         * if we have more than one endpoint we are definitely in download
         * mode
         */
        if (interface->bNumEndpoints > 1) {
                serial->product_info.TiMode = TI_MODE_DOWNLOAD;
                status = do_download_mode(serial, fw);
        } else {
                /* Otherwise we will remain in configuring mode */
                serial->product_info.TiMode = TI_MODE_CONFIGURING;
                status = do_boot_mode(serial, fw);
        }

out:
        release_firmware(fw);
        return status;
}

static int do_download_mode(struct edgeport_serial *serial,
                const struct firmware *fw)
{
        struct device *dev = &serial->serial->interface->dev;
        int status = 0;
        int start_address;
        struct edge_ti_manuf_descriptor *ti_manuf_desc;
        int download_cur_ver;
        int download_new_ver;
        struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data;
        struct ti_i2c_desc *rom_desc;

        dev_dbg(dev, "%s - RUNNING IN DOWNLOAD MODE\n", __func__);

        status = check_i2c_image(serial);
        if (status) {
                dev_dbg(dev, "%s - DOWNLOAD MODE -- BAD I2C\n", __func__);
                return status;
        }

        /*
         * Validate Hardware version number
         * Read Manufacturing Descriptor from TI Based Edgeport
         */
        ti_manuf_desc = kmalloc(sizeof(*ti_manuf_desc), GFP_KERNEL);
        if (!ti_manuf_desc)
                return -ENOMEM;

        status = get_manuf_info(serial, (__u8 *)ti_manuf_desc);
        if (status) {
                kfree(ti_manuf_desc);
                return status;
        }

        /* Check version number of ION descriptor */
        if (!ignore_cpu_rev && ti_cpu_rev(ti_manuf_desc) < 2) {
                dev_dbg(dev, "%s - Wrong CPU Rev %d (Must be 2)\n",
                        __func__, ti_cpu_rev(ti_manuf_desc));
                kfree(ti_manuf_desc);
                return -EINVAL;
        }

        rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL);
        if (!rom_desc) {
                kfree(ti_manuf_desc);
                return -ENOMEM;
        }

        /* Search for type 2 record (firmware record) */
        start_address = get_descriptor_addr(serial,
                        I2C_DESC_TYPE_FIRMWARE_BASIC, rom_desc);
        if (start_address != 0) {
                struct ti_i2c_firmware_rec *firmware_version;
                u8 *record;

                dev_dbg(dev, "%s - Found Type FIRMWARE (Type 2) record\n",
                                __func__);

                firmware_version = kmalloc(sizeof(*firmware_version),
                                                        GFP_KERNEL);
                if (!firmware_version) {
                        kfree(rom_desc);
                        kfree(ti_manuf_desc);
                        return -ENOMEM;
                }

                /*
                 * Validate version number
                 * Read the descriptor data
                 */
                status = read_rom(serial, start_address +
                                sizeof(struct ti_i2c_desc),
                                sizeof(struct ti_i2c_firmware_rec),
                                (__u8 *)firmware_version);
                if (status) {
                        kfree(firmware_version);
                        kfree(rom_desc);
                        kfree(ti_manuf_desc);
                        return status;
                }

                /*
                 * Check version number of download with current
                 * version in I2c
                 */
                download_cur_ver = (firmware_version->Ver_Major << 8) +
                                   (firmware_version->Ver_Minor);
                download_new_ver = (fw_hdr->major_version << 8) +
                                   (fw_hdr->minor_version);

                dev_dbg(dev, "%s - >> FW Versions Device %d.%d  Driver %d.%d\n",
                        __func__, firmware_version->Ver_Major,
                        firmware_version->Ver_Minor,
                        fw_hdr->major_version, fw_hdr->minor_version);

                /*
                 * Check if we have an old version in the I2C and
                 * update if necessary
                 */
                if (download_cur_ver < download_new_ver) {
                        dev_dbg(dev, "%s - Update I2C dld from %d.%d to %d.%d\n",
                                __func__,
                                firmware_version->Ver_Major,
                                firmware_version->Ver_Minor,
                                fw_hdr->major_version,
                                fw_hdr->minor_version);

                        record = kmalloc(1, GFP_KERNEL);
                        if (!record) {
                                kfree(firmware_version);
                                kfree(rom_desc);
                                kfree(ti_manuf_desc);
                                return -ENOMEM;
                        }
                        /*
                         * In order to update the I2C firmware we must
                         * change the type 2 record to type 0xF2. This
                         * will force the UMP to come up in Boot Mode.
                         * Then while in boot mode, the driver will
                         * download the latest firmware (padded to
                         * 15.5k) into the UMP ram. Finally when the
                         * device comes back up in download mode the
                         * driver will cause the new firmware to be
                         * copied from the UMP Ram to I2C and the
                         * firmware will update the record type from
                         * 0xf2 to 0x02.
                         */
                        *record = I2C_DESC_TYPE_FIRMWARE_BLANK;

                        /*
                         * Change the I2C Firmware record type to
                         * 0xf2 to trigger an update
                         */
                        status = write_rom(serial, start_address,
                                        sizeof(*record), record);
                        if (status) {
                                kfree(record);
                                kfree(firmware_version);
                                kfree(rom_desc);
                                kfree(ti_manuf_desc);
                                return status;
                        }

                        /*
                         * verify the write -- must do this in order
                         * for write to complete before we do the
                         * hardware reset
                         */
                        status = read_rom(serial,
                                                start_address,
                                                sizeof(*record),
                                                record);
                        if (status) {
                                kfree(record);
                                kfree(firmware_version);
                                kfree(rom_desc);
                                kfree(ti_manuf_desc);
                                return status;
                        }

                        if (*record != I2C_DESC_TYPE_FIRMWARE_BLANK) {
                                dev_err(dev, "%s - error resetting device\n",
                                                __func__);
                                kfree(record);
                                kfree(firmware_version);
                                kfree(rom_desc);
                                kfree(ti_manuf_desc);
                                return -ENODEV;
                        }

                        dev_dbg(dev, "%s - HARDWARE RESET\n", __func__);

                        /* Reset UMP -- Back to BOOT MODE */
                        status = ti_vsend_sync(serial->serial->dev,
                                        UMPC_HARDWARE_RESET,
                                        0, 0, NULL, 0,
                                        TI_VSEND_TIMEOUT_DEFAULT);

                        dev_dbg(dev, "%s - HARDWARE RESET return %d\n",
                                        __func__, status);

                        /* return an error on purpose. */
                        kfree(record);
                        kfree(firmware_version);
                        kfree(rom_desc);
                        kfree(ti_manuf_desc);
                        return -ENODEV;
                }
                /* Same or newer fw version is already loaded */
                serial->fw_version = download_cur_ver;
                kfree(firmware_version);
        }
        /* Search for type 0xF2 record (firmware blank record) */
        else {
                start_address = get_descriptor_addr(serial,
                                I2C_DESC_TYPE_FIRMWARE_BLANK, rom_desc);
                if (start_address != 0) {
#define HEADER_SIZE     (sizeof(struct ti_i2c_desc) + \
                                sizeof(struct ti_i2c_firmware_rec))
                        __u8 *header;
                        __u8 *vheader;

                        header = kmalloc(HEADER_SIZE, GFP_KERNEL);
                        if (!header) {
                                kfree(rom_desc);
                                kfree(ti_manuf_desc);
                                return -ENOMEM;
                        }

                        vheader = kmalloc(HEADER_SIZE, GFP_KERNEL);
                        if (!vheader) {
                                kfree(header);
                                kfree(rom_desc);
                                kfree(ti_manuf_desc);
                                return -ENOMEM;
                        }

                        dev_dbg(dev, "%s - Found Type BLANK FIRMWARE (Type F2) record\n",
                                        __func__);

                        /*
                         * In order to update the I2C firmware we must change
                         * the type 2 record to type 0xF2. This will force the
                         * UMP to come up in Boot Mode.  Then while in boot
                         * mode, the driver will download the latest firmware
                         * (padded to 15.5k) into the UMP ram. Finally when the
                         * device comes back up in download mode the driver
                         * will cause the new firmware to be copied from the
                         * UMP Ram to I2C and the firmware will update the
                         * record type from 0xf2 to 0x02.
                         */
                        status = build_i2c_fw_hdr(header, fw);
                        if (status) {
                                kfree(vheader);
                                kfree(header);
                                kfree(rom_desc);
                                kfree(ti_manuf_desc);
                                return -EINVAL;
                        }

                        /*
                         * Update I2C with type 0xf2 record with correct
                         * size and checksum
                         */
                        status = write_rom(serial,
                                                start_address,
                                                HEADER_SIZE,
                                                header);
                        if (status) {
                                kfree(vheader);
                                kfree(header);
                                kfree(rom_desc);
                                kfree(ti_manuf_desc);
                                return -EINVAL;
                        }

                        /*
                         * verify the write -- must do this in order for
                         * write to complete before we do the hardware reset
                         */
                        status = read_rom(serial, start_address,
                                                        HEADER_SIZE, vheader);

                        if (status) {
                                dev_dbg(dev, "%s - can't read header back\n",
                                                __func__);
                                kfree(vheader);
                                kfree(header);
                                kfree(rom_desc);
                                kfree(ti_manuf_desc);
                                return status;
                        }
                        if (memcmp(vheader, header, HEADER_SIZE)) {
                                dev_dbg(dev, "%s - write download record failed\n",
                                                __func__);
                                kfree(vheader);
                                kfree(header);
                                kfree(rom_desc);
                                kfree(ti_manuf_desc);
                                return -EINVAL;
                        }

                        kfree(vheader);
                        kfree(header);

                        dev_dbg(dev, "%s - Start firmware update\n", __func__);

                        /* Tell firmware to copy download image into I2C */
                        status = ti_vsend_sync(serial->serial->dev,
                                        UMPC_COPY_DNLD_TO_I2C,
                                        0, 0, NULL, 0,
                                        TI_VSEND_TIMEOUT_FW_DOWNLOAD);

                        dev_dbg(dev, "%s - Update complete 0x%x\n", __func__,
                                        status);
                        if (status) {
                                dev_err(dev,
                                        "%s - UMPC_COPY_DNLD_TO_I2C failed\n",
                                        __func__);
                                kfree(rom_desc);
                                kfree(ti_manuf_desc);
                                return status;
                        }
                }
        }

        /* The device is running the download code */
        kfree(rom_desc);
        kfree(ti_manuf_desc);
        return 0;
}

static int do_boot_mode(struct edgeport_serial *serial,
                const struct firmware *fw)
{
        struct device *dev = &serial->serial->interface->dev;
        int status = 0;
        struct edge_ti_manuf_descriptor *ti_manuf_desc;
        struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data;

        dev_dbg(dev, "%s - RUNNING IN BOOT MODE\n", __func__);

        /* Configure the TI device so we can use the BULK pipes for download */
        status = config_boot_dev(serial->serial->dev);
        if (status)
                return status;

        if (le16_to_cpu(serial->serial->dev->descriptor.idVendor)
                                                        != USB_VENDOR_ID_ION) {
                dev_dbg(dev, "%s - VID = 0x%x\n", __func__,
                        le16_to_cpu(serial->serial->dev->descriptor.idVendor));
                serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;
                goto stayinbootmode;
        }

        /*
         * We have an ION device (I2c Must be programmed)
         * Determine I2C image type
         */
        if (i2c_type_bootmode(serial))
                goto stayinbootmode;

        /* Check for ION Vendor ID and that the I2C is valid */
        if (!check_i2c_image(serial)) {
                struct ti_i2c_image_header *header;
                int i;
                __u8 cs = 0;
                __u8 *buffer;
                int buffer_size;

                /*
                 * Validate Hardware version number
                 * Read Manufacturing Descriptor from TI Based Edgeport
                 */
                ti_manuf_desc = kmalloc(sizeof(*ti_manuf_desc), GFP_KERNEL);
                if (!ti_manuf_desc)
                        return -ENOMEM;

                status = get_manuf_info(serial, (__u8 *)ti_manuf_desc);
                if (status) {
                        kfree(ti_manuf_desc);
                        goto stayinbootmode;
                }

                /* Check for version 2 */
                if (!ignore_cpu_rev && ti_cpu_rev(ti_manuf_desc) < 2) {
                        dev_dbg(dev, "%s - Wrong CPU Rev %d (Must be 2)\n",
                                __func__, ti_cpu_rev(ti_manuf_desc));
                        kfree(ti_manuf_desc);
                        goto stayinbootmode;
                }

                kfree(ti_manuf_desc);

                /*
                 * In order to update the I2C firmware we must change the type
                 * 2 record to type 0xF2. This will force the UMP to come up
                 * in Boot Mode.  Then while in boot mode, the driver will
                 * download the latest firmware (padded to 15.5k) into the
                 * UMP ram. Finally when the device comes back up in download
                 * mode the driver will cause the new firmware to be copied
                 * from the UMP Ram to I2C and the firmware will update the
                 * record type from 0xf2 to 0x02.
                 *
                 * Do we really have to copy the whole firmware image,
                 * or could we do this in place!
                 */

                /* Allocate a 15.5k buffer + 3 byte header */
                buffer_size = (((1024 * 16) - 512) +
                                        sizeof(struct ti_i2c_image_header));
                buffer = kmalloc(buffer_size, GFP_KERNEL);
                if (!buffer)
                        return -ENOMEM;

                /* Initialize the buffer to 0xff (pad the buffer) */
                memset(buffer, 0xff, buffer_size);
                memcpy(buffer, &fw->data[4], fw->size - 4);

                for (i = sizeof(struct ti_i2c_image_header);
                                i < buffer_size; i++) {
                        cs = (__u8)(cs + buffer[i]);
                }

                header = (struct ti_i2c_image_header *)buffer;

                /* update length and checksum after padding */
                header->Length   = cpu_to_le16((__u16)(buffer_size -
                                        sizeof(struct ti_i2c_image_header)));
                header->CheckSum = cs;

                /* Download the operational code  */
                dev_dbg(dev, "%s - Downloading operational code image version %d.%d (TI UMP)\n",
                                __func__,
                                fw_hdr->major_version, fw_hdr->minor_version);
                status = download_code(serial, buffer, buffer_size);

                kfree(buffer);

                if (status) {
                        dev_dbg(dev, "%s - Error downloading operational code image\n", __func__);
                        return status;
                }

                /* Device will reboot */
                serial->product_info.TiMode = TI_MODE_TRANSITIONING;

                dev_dbg(dev, "%s - Download successful -- Device rebooting...\n", __func__);

                return 1;
        }

stayinbootmode:
        /* Eprom is invalid or blank stay in boot mode */
        dev_dbg(dev, "%s - STAYING IN BOOT MODE\n", __func__);
        serial->product_info.TiMode = TI_MODE_BOOT;

        return 1;
}

static int ti_do_config(struct edgeport_port *port, int feature, int on)
{
        int port_number = port->port->port_number;

        on = !!on;      /* 1 or 0 not bitmask */
        return send_cmd(port->port->serial->dev,
                        feature, (__u8)(UMPM_UART1_PORT + port_number),
                        on, NULL, 0);
}

static int restore_mcr(struct edgeport_port *port, __u8 mcr)
{
        int status = 0;

        dev_dbg(&port->port->dev, "%s - %x\n", __func__, mcr);

        status = ti_do_config(port, UMPC_SET_CLR_DTR, mcr & MCR_DTR);
        if (status)
                return status;
        status = ti_do_config(port, UMPC_SET_CLR_RTS, mcr & MCR_RTS);
        if (status)
                return status;
        return ti_do_config(port, UMPC_SET_CLR_LOOPBACK, mcr & MCR_LOOPBACK);
}

/* Convert TI LSR to standard UART flags */
static __u8 map_line_status(__u8 ti_lsr)
{
        __u8 lsr = 0;

#define MAP_FLAG(flagUmp, flagUart)    \
        if (ti_lsr & flagUmp) \
                lsr |= flagUart;

        MAP_FLAG(UMP_UART_LSR_OV_MASK, LSR_OVER_ERR)    /* overrun */
        MAP_FLAG(UMP_UART_LSR_PE_MASK, LSR_PAR_ERR)     /* parity error */
        MAP_FLAG(UMP_UART_LSR_FE_MASK, LSR_FRM_ERR)     /* framing error */
        MAP_FLAG(UMP_UART_LSR_BR_MASK, LSR_BREAK)       /* break detected */
        MAP_FLAG(UMP_UART_LSR_RX_MASK, LSR_RX_AVAIL)    /* rx data available */
        MAP_FLAG(UMP_UART_LSR_TX_MASK, LSR_TX_EMPTY)    /* tx hold reg empty */

#undef MAP_FLAG

        return lsr;
}

static void handle_new_msr(struct edgeport_port *edge_port, __u8 msr)
{
        struct async_icount *icount;
        struct tty_struct *tty;

        dev_dbg(&edge_port->port->dev, "%s - %02x\n", __func__, msr);

        if (msr & (EDGEPORT_MSR_DELTA_CTS | EDGEPORT_MSR_DELTA_DSR |
                        EDGEPORT_MSR_DELTA_RI | EDGEPORT_MSR_DELTA_CD)) {
                icount = &edge_port->port->icount;

                /* update input line counters */
                if (msr & EDGEPORT_MSR_DELTA_CTS)
                        icount->cts++;
                if (msr & EDGEPORT_MSR_DELTA_DSR)
                        icount->dsr++;
                if (msr & EDGEPORT_MSR_DELTA_CD)
                        icount->dcd++;
                if (msr & EDGEPORT_MSR_DELTA_RI)
                        icount->rng++;
                wake_up_interruptible(&edge_port->port->port.delta_msr_wait);
        }

        /* Save the new modem status */
        edge_port->shadow_msr = msr & 0xf0;

        tty = tty_port_tty_get(&edge_port->port->port);
        /* handle CTS flow control */
        if (tty && C_CRTSCTS(tty)) {
                if (msr & EDGEPORT_MSR_CTS)
                        tty_wakeup(tty);
        }
        tty_kref_put(tty);
}

static void handle_new_lsr(struct edgeport_port *edge_port, int lsr_data,
                                                        __u8 lsr, __u8 data)
{
        struct async_icount *icount;
        __u8 new_lsr = (__u8)(lsr & (__u8)(LSR_OVER_ERR | LSR_PAR_ERR |
                                                LSR_FRM_ERR | LSR_BREAK));

        dev_dbg(&edge_port->port->dev, "%s - %02x\n", __func__, new_lsr);

        edge_port->shadow_lsr = lsr;

        if (new_lsr & LSR_BREAK)
                /*
                 * Parity and Framing errors only count if they
                 * occur exclusive of a break being received.
                 */
                new_lsr &= (__u8)(LSR_OVER_ERR | LSR_BREAK);

        /* Place LSR data byte into Rx buffer */
        if (lsr_data)
                edge_tty_recv(edge_port->port, &data, 1);

        /* update input line counters */
        icount = &edge_port->port->icount;
        if (new_lsr & LSR_BREAK)
                icount->brk++;
        if (new_lsr & LSR_OVER_ERR)
                icount->overrun++;
        if (new_lsr & LSR_PAR_ERR)
                icount->parity++;
        if (new_lsr & LSR_FRM_ERR)
                icount->frame++;
}

static void edge_interrupt_callback(struct urb *urb)
{
        struct edgeport_serial *edge_serial = urb->context;
        struct usb_serial_port *port;
        struct edgeport_port *edge_port;
        struct device *dev;
        unsigned char *data = urb->transfer_buffer;
        int length = urb->actual_length;
        int port_number;
        int function;
        int retval;
        __u8 lsr;
        __u8 msr;
        int status = urb->status;

        switch (status) {
        case 0:
                /* success */
                break;
        case -ECONNRESET:
        case -ENOENT:
        case -ESHUTDOWN:
                /* this urb is terminated, clean up */
                dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n",
                    __func__, status);
                return;
        default:
                dev_err(&urb->dev->dev, "%s - nonzero urb status received: "
                        "%d\n", __func__, status);
                goto exit;
        }

        if (!length) {
                dev_dbg(&urb->dev->dev, "%s - no data in urb\n", __func__);
                goto exit;
        }

        dev = &edge_serial->serial->dev->dev;
        usb_serial_debug_data(dev, __func__, length, data);

        if (length != 2) {
                dev_dbg(dev, "%s - expecting packet of size 2, got %d\n", __func__, length);
                goto exit;
        }

        port_number = TIUMP_GET_PORT_FROM_CODE(data[0]);
        function    = TIUMP_GET_FUNC_FROM_CODE(data[0]);
        dev_dbg(dev, "%s - port_number %d, function %d, info 0x%x\n", __func__,
                port_number, function, data[1]);

        if (port_number >= edge_serial->serial->num_ports) {
                dev_err(dev, "bad port number %d\n", port_number);
                goto exit;
        }

        port = edge_serial->serial->port[port_number];
        edge_port = usb_get_serial_port_data(port);
        if (!edge_port) {
                dev_dbg(dev, "%s - edge_port not found\n", __func__);
                return;
        }
        switch (function) {
        case TIUMP_INTERRUPT_CODE_LSR:
                lsr = map_line_status(data[1]);
                if (lsr & UMP_UART_LSR_DATA_MASK) {
                        /*
                         * Save the LSR event for bulk read completion routine
                         */
                        dev_dbg(dev, "%s - LSR Event Port %u LSR Status = %02x\n",
                                __func__, port_number, lsr);
                        edge_port->lsr_event = 1;
                        edge_port->lsr_mask = lsr;
                } else {
                        dev_dbg(dev, "%s - ===== Port %d LSR Status = %02x ======\n",
                                __func__, port_number, lsr);
                        handle_new_lsr(edge_port, 0, lsr, 0);
                }
                break;

        case TIUMP_INTERRUPT_CODE_MSR:  /* MSR */
                /* Copy MSR from UMP */
                msr = data[1];
                dev_dbg(dev, "%s - ===== Port %u MSR Status = %02x ======\n",
                        __func__, port_number, msr);
                handle_new_msr(edge_port, msr);
                break;

        default:
                dev_err(&urb->dev->dev,
                        "%s - Unknown Interrupt code from UMP %x\n",
                        __func__, data[1]);
                break;

        }

exit:
        retval = usb_submit_urb(urb, GFP_ATOMIC);
        if (retval)
                dev_err(&urb->dev->dev,
                        "%s - usb_submit_urb failed with result %d\n",
                         __func__, retval);
}

static void edge_bulk_in_callback(struct urb *urb)
{
        struct edgeport_port *edge_port = urb->context;
        struct device *dev = &edge_port->port->dev;
        unsigned char *data = urb->transfer_buffer;
        unsigned long flags;
        int retval = 0;
        int port_number;
        int status = urb->status;

        switch (status) {
        case 0:
                /* success */
                break;
        case -ECONNRESET:
        case -ENOENT:
        case -ESHUTDOWN:
                /* this urb is terminated, clean up */
                dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", __func__, status);
                return;
        default:
                dev_err(&urb->dev->dev, "%s - nonzero read bulk status received: %d\n", __func__, status);
        }

        if (status == -EPIPE)
                goto exit;

        if (status) {
                dev_err(&urb->dev->dev, "%s - stopping read!\n", __func__);
                return;
        }

        port_number = edge_port->port->port_number;

        if (urb->actual_length > 0 && edge_port->lsr_event) {
                edge_port->lsr_event = 0;
                dev_dbg(dev, "%s ===== Port %u LSR Status = %02x, Data = %02x ======\n",
                        __func__, port_number, edge_port->lsr_mask, *data);
                handle_new_lsr(edge_port, 1, edge_port->lsr_mask, *data);
                /* Adjust buffer length/pointer */
                --urb->actual_length;
                ++data;
        }

        if (urb->actual_length) {
                usb_serial_debug_data(dev, __func__, urb->actual_length, data);
                if (edge_port->close_pending)
                        dev_dbg(dev, "%s - close pending, dropping data on the floor\n",
                                                                __func__);
                else
                        edge_tty_recv(edge_port->port, data,
                                        urb->actual_length);
                edge_port->port->icount.rx += urb->actual_length;
        }

exit:
        /* continue read unless stopped */
        spin_lock_irqsave(&edge_port->ep_lock, flags);
        if (edge_port->ep_read_urb_state == EDGE_READ_URB_RUNNING)
                retval = usb_submit_urb(urb, GFP_ATOMIC);
        else if (edge_port->ep_read_urb_state == EDGE_READ_URB_STOPPING)
                edge_port->ep_read_urb_state = EDGE_READ_URB_STOPPED;

        spin_unlock_irqrestore(&edge_port->ep_lock, flags);
        if (retval)
                dev_err(dev, "%s - usb_submit_urb failed with result %d\n", __func__, retval);
}

static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data,
                int length)
{
        int queued;

        queued = tty_insert_flip_string(&port->port, data, length);
        if (queued < length)
                dev_err(&port->dev, "%s - dropping data, %d bytes lost\n",
                        __func__, length - queued);
        tty_flip_buffer_push(&port->port);
}

static void edge_bulk_out_callback(struct urb *urb)
{
        struct usb_serial_port *port = urb->context;
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        int status = urb->status;
        struct tty_struct *tty;

        edge_port->ep_write_urb_in_use = 0;

        switch (status) {
        case 0:
                /* success */
                break;
        case -ECONNRESET:
        case -ENOENT:
        case -ESHUTDOWN:
                /* this urb is terminated, clean up */
                dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n",
                    __func__, status);
                return;
        default:
                dev_err_console(port, "%s - nonzero write bulk status "
                        "received: %d\n", __func__, status);
        }

        /* send any buffered data */
        tty = tty_port_tty_get(&port->port);
        edge_send(port, tty);
        tty_kref_put(tty);
}

static int edge_open(struct tty_struct *tty, struct usb_serial_port *port)
{
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        struct edgeport_serial *edge_serial;
        struct usb_device *dev;
        struct urb *urb;
        int port_number;
        int status;
        u16 open_settings;
        u8 transaction_timeout;

        if (edge_port == NULL)
                return -ENODEV;

        port_number = port->port_number;

        dev = port->serial->dev;

        /* turn off loopback */
        status = ti_do_config(edge_port, UMPC_SET_CLR_LOOPBACK, 0);
        if (status) {
                dev_err(&port->dev,
                                "%s - cannot send clear loopback command, %d\n",
                        __func__, status);
                return status;
        }

        /* set up the port settings */
        if (tty)
                edge_set_termios(tty, port, &tty->termios);

        /* open up the port */

        /* milliseconds to timeout for DMA transfer */
        transaction_timeout = 2;

        edge_port->ump_read_timeout =
                                max(20, ((transaction_timeout * 3) / 2));

        /* milliseconds to timeout for DMA transfer */
        open_settings = (u8)(UMP_DMA_MODE_CONTINOUS |
                             UMP_PIPE_TRANS_TIMEOUT_ENA |
                             (transaction_timeout << 2));

        dev_dbg(&port->dev, "%s - Sending UMPC_OPEN_PORT\n", __func__);

        /* Tell TI to open and start the port */
        status = send_cmd(dev, UMPC_OPEN_PORT,
                (u8)(UMPM_UART1_PORT + port_number), open_settings, NULL, 0);
        if (status) {
                dev_err(&port->dev, "%s - cannot send open command, %d\n",
                                                        __func__, status);
                return status;
        }

        /* Start the DMA? */
        status = send_cmd(dev, UMPC_START_PORT,
                (u8)(UMPM_UART1_PORT + port_number), 0, NULL, 0);
        if (status) {
                dev_err(&port->dev, "%s - cannot send start DMA command, %d\n",
                                                        __func__, status);
                return status;
        }

        /* Clear TX and RX buffers in UMP */
        status = purge_port(port, UMP_PORT_DIR_OUT | UMP_PORT_DIR_IN);
        if (status) {
                dev_err(&port->dev,
                        "%s - cannot send clear buffers command, %d\n",
                        __func__, status);
                return status;
        }

        /* Read Initial MSR */
        status = ti_vread_sync(dev, UMPC_READ_MSR, 0,
                                (__u16)(UMPM_UART1_PORT + port_number),
                                &edge_port->shadow_msr, 1);
        if (status) {
                dev_err(&port->dev, "%s - cannot send read MSR command, %d\n",
                                                        __func__, status);
                return status;
        }

        dev_dbg(&port->dev, "ShadowMSR 0x%X\n", edge_port->shadow_msr);

        /* Set Initial MCR */
        edge_port->shadow_mcr = MCR_RTS | MCR_DTR;
        dev_dbg(&port->dev, "ShadowMCR 0x%X\n", edge_port->shadow_mcr);

        edge_serial = edge_port->edge_serial;
        if (mutex_lock_interruptible(&edge_serial->es_lock))
                return -ERESTARTSYS;
        if (edge_serial->num_ports_open == 0) {
                /* we are the first port to open, post the interrupt urb */
                urb = edge_serial->serial->port[0]->interrupt_in_urb;
                urb->context = edge_serial;
                status = usb_submit_urb(urb, GFP_KERNEL);
                if (status) {
                        dev_err(&port->dev,
                                "%s - usb_submit_urb failed with value %d\n",
                                        __func__, status);
                        goto release_es_lock;
                }
        }

        /*
         * reset the data toggle on the bulk endpoints to work around bug in
         * host controllers where things get out of sync some times
         */
        usb_clear_halt(dev, port->write_urb->pipe);
        usb_clear_halt(dev, port->read_urb->pipe);

        /* start up our bulk read urb */
        urb = port->read_urb;
        edge_port->ep_read_urb_state = EDGE_READ_URB_RUNNING;
        urb->context = edge_port;
        status = usb_submit_urb(urb, GFP_KERNEL);
        if (status) {
                dev_err(&port->dev,
                        "%s - read bulk usb_submit_urb failed with value %d\n",
                                __func__, status);
                goto unlink_int_urb;
        }

        ++edge_serial->num_ports_open;

        goto release_es_lock;

unlink_int_urb:
        if (edge_port->edge_serial->num_ports_open == 0)
                usb_kill_urb(port->serial->port[0]->interrupt_in_urb);
release_es_lock:
        mutex_unlock(&edge_serial->es_lock);
        return status;
}

static void edge_close(struct usb_serial_port *port)
{
        struct edgeport_serial *edge_serial;
        struct edgeport_port *edge_port;
        struct usb_serial *serial = port->serial;
        unsigned long flags;
        int port_number;

        edge_serial = usb_get_serial_data(port->serial);
        edge_port = usb_get_serial_port_data(port);
        if (edge_serial == NULL || edge_port == NULL)
                return;

        /*
         * The bulkreadcompletion routine will check
         * this flag and dump add read data
         */
        edge_port->close_pending = 1;

        usb_kill_urb(port->read_urb);
        usb_kill_urb(port->write_urb);
        edge_port->ep_write_urb_in_use = 0;
        spin_lock_irqsave(&edge_port->ep_lock, flags);
        kfifo_reset_out(&port->write_fifo);
        spin_unlock_irqrestore(&edge_port->ep_lock, flags);

        dev_dbg(&port->dev, "%s - send umpc_close_port\n", __func__);

        port_number = port->port_number;
        send_cmd(serial->dev, UMPC_CLOSE_PORT,
                     (__u8)(UMPM_UART1_PORT + port_number), 0, NULL, 0);

        mutex_lock(&edge_serial->es_lock);
        --edge_port->edge_serial->num_ports_open;
        if (edge_port->edge_serial->num_ports_open <= 0) {
                /* last port is now closed, let's shut down our interrupt urb */
                usb_kill_urb(port->serial->port[0]->interrupt_in_urb);
                edge_port->edge_serial->num_ports_open = 0;
        }
        mutex_unlock(&edge_serial->es_lock);
        edge_port->close_pending = 0;
}

static int edge_write(struct tty_struct *tty, struct usb_serial_port *port,
                                const unsigned char *data, int count)
{
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);

        if (count == 0) {
                dev_dbg(&port->dev, "%s - write request of 0 bytes\n", __func__);
                return 0;
        }

        if (edge_port == NULL)
                return -ENODEV;
        if (edge_port->close_pending == 1)
                return -ENODEV;

        count = kfifo_in_locked(&port->write_fifo, data, count,
                                                        &edge_port->ep_lock);
        edge_send(port, tty);

        return count;
}

static void edge_send(struct usb_serial_port *port, struct tty_struct *tty)
{
        int count, result;
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        unsigned long flags;

        spin_lock_irqsave(&edge_port->ep_lock, flags);

        if (edge_port->ep_write_urb_in_use) {
                spin_unlock_irqrestore(&edge_port->ep_lock, flags);
                return;
        }

        count = kfifo_out(&port->write_fifo,
                                port->write_urb->transfer_buffer,
                                port->bulk_out_size);

        if (count == 0) {
                spin_unlock_irqrestore(&edge_port->ep_lock, flags);
                return;
        }

        edge_port->ep_write_urb_in_use = 1;

        spin_unlock_irqrestore(&edge_port->ep_lock, flags);

        usb_serial_debug_data(&port->dev, __func__, count, port->write_urb->transfer_buffer);

        /* set up our urb */
        port->write_urb->transfer_buffer_length = count;

        /* send the data out the bulk port */
        result = usb_submit_urb(port->write_urb, GFP_ATOMIC);
        if (result) {
                dev_err_console(port,
                        "%s - failed submitting write urb, error %d\n",
                                __func__, result);
                edge_port->ep_write_urb_in_use = 0;
                /* TODO: reschedule edge_send */
        } else
                edge_port->port->icount.tx += count;

        /*
         * wakeup any process waiting for writes to complete
         * there is now more room in the buffer for new writes
         */
        if (tty)
                tty_wakeup(tty);
}

static int edge_write_room(struct tty_struct *tty)
{
        struct usb_serial_port *port = tty->driver_data;
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        int room = 0;
        unsigned long flags;

        if (edge_port == NULL)
                return 0;
        if (edge_port->close_pending == 1)
                return 0;

        spin_lock_irqsave(&edge_port->ep_lock, flags);
        room = kfifo_avail(&port->write_fifo);
        spin_unlock_irqrestore(&edge_port->ep_lock, flags);

        dev_dbg(&port->dev, "%s - returns %d\n", __func__, room);
        return room;
}

static int edge_chars_in_buffer(struct tty_struct *tty)
{
        struct usb_serial_port *port = tty->driver_data;
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        int chars = 0;
        unsigned long flags;
        if (edge_port == NULL)
                return 0;

        spin_lock_irqsave(&edge_port->ep_lock, flags);
        chars = kfifo_len(&port->write_fifo);
        spin_unlock_irqrestore(&edge_port->ep_lock, flags);

        dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars);
        return chars;
}

static bool edge_tx_empty(struct usb_serial_port *port)
{
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        int ret;

        ret = tx_active(edge_port);
        if (ret > 0)
                return false;

        return true;
}

static void edge_throttle(struct tty_struct *tty)
{
        struct usb_serial_port *port = tty->driver_data;
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        int status;

        if (edge_port == NULL)
                return;

        /* if we are implementing XON/XOFF, send the stop character */
        if (I_IXOFF(tty)) {
                unsigned char stop_char = STOP_CHAR(tty);
                status = edge_write(tty, port, &stop_char, 1);
                if (status <= 0) {
                        dev_err(&port->dev, "%s - failed to write stop character, %d\n", __func__, status);
                }
        }

        /*
         * if we are implementing RTS/CTS, stop reads
         * and the Edgeport will clear the RTS line
         */
        if (C_CRTSCTS(tty))
                stop_read(edge_port);

}

static void edge_unthrottle(struct tty_struct *tty)
{
        struct usb_serial_port *port = tty->driver_data;
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        int status;

        if (edge_port == NULL)
                return;

        /* if we are implementing XON/XOFF, send the start character */
        if (I_IXOFF(tty)) {
                unsigned char start_char = START_CHAR(tty);
                status = edge_write(tty, port, &start_char, 1);
                if (status <= 0) {
                        dev_err(&port->dev, "%s - failed to write start character, %d\n", __func__, status);
                }
        }
        /*
         * if we are implementing RTS/CTS, restart reads
         * are the Edgeport will assert the RTS line
         */
        if (C_CRTSCTS(tty)) {
                status = restart_read(edge_port);
                if (status)
                        dev_err(&port->dev,
                                "%s - read bulk usb_submit_urb failed: %d\n",
                                                        __func__, status);
        }

}

static void stop_read(struct edgeport_port *edge_port)
{
        unsigned long flags;

        spin_lock_irqsave(&edge_port->ep_lock, flags);

        if (edge_port->ep_read_urb_state == EDGE_READ_URB_RUNNING)
                edge_port->ep_read_urb_state = EDGE_READ_URB_STOPPING;
        edge_port->shadow_mcr &= ~MCR_RTS;

        spin_unlock_irqrestore(&edge_port->ep_lock, flags);
}

static int restart_read(struct edgeport_port *edge_port)
{
        struct urb *urb;
        int status = 0;
        unsigned long flags;

        spin_lock_irqsave(&edge_port->ep_lock, flags);

        if (edge_port->ep_read_urb_state == EDGE_READ_URB_STOPPED) {
                urb = edge_port->port->read_urb;
                status = usb_submit_urb(urb, GFP_ATOMIC);
        }
        edge_port->ep_read_urb_state = EDGE_READ_URB_RUNNING;
        edge_port->shadow_mcr |= MCR_RTS;

        spin_unlock_irqrestore(&edge_port->ep_lock, flags);

        return status;
}

static void change_port_settings(struct tty_struct *tty,
                struct edgeport_port *edge_port, struct ktermios *old_termios)
{
        struct device *dev = &edge_port->port->dev;
        struct ump_uart_config *config;
        int baud;
        unsigned cflag;
        int status;
        int port_number = edge_port->port->port_number;

        config = kmalloc (sizeof (*config), GFP_KERNEL);
        if (!config) {
                tty->termios = *old_termios;
                return;
        }

        cflag = tty->termios.c_cflag;

        config->wFlags = 0;

        /* These flags must be set */
        config->wFlags |= UMP_MASK_UART_FLAGS_RECEIVE_MS_INT;
        config->wFlags |= UMP_MASK_UART_FLAGS_AUTO_START_ON_ERR;
        config->bUartMode = (__u8)(edge_port->bUartMode);

        switch (cflag & CSIZE) {
        case CS5:
                    config->bDataBits = UMP_UART_CHAR5BITS;
                    dev_dbg(dev, "%s - data bits = 5\n", __func__);
                    break;
        case CS6:
                    config->bDataBits = UMP_UART_CHAR6BITS;
                    dev_dbg(dev, "%s - data bits = 6\n", __func__);
                    break;
        case CS7:
                    config->bDataBits = UMP_UART_CHAR7BITS;
                    dev_dbg(dev, "%s - data bits = 7\n", __func__);
                    break;
        default:
        case CS8:
                    config->bDataBits = UMP_UART_CHAR8BITS;
                    dev_dbg(dev, "%s - data bits = 8\n", __func__);
                            break;
        }

        if (cflag & PARENB) {
                if (cflag & PARODD) {
                        config->wFlags |= UMP_MASK_UART_FLAGS_PARITY;
                        config->bParity = UMP_UART_ODDPARITY;
                        dev_dbg(dev, "%s - parity = odd\n", __func__);
                } else {
                        config->wFlags |= UMP_MASK_UART_FLAGS_PARITY;
                        config->bParity = UMP_UART_EVENPARITY;
                        dev_dbg(dev, "%s - parity = even\n", __func__);
                }
        } else {
                config->bParity = UMP_UART_NOPARITY;
                dev_dbg(dev, "%s - parity = none\n", __func__);
        }

        if (cflag & CSTOPB) {
                config->bStopBits = UMP_UART_STOPBIT2;
                dev_dbg(dev, "%s - stop bits = 2\n", __func__);
        } else {
                config->bStopBits = UMP_UART_STOPBIT1;
                dev_dbg(dev, "%s - stop bits = 1\n", __func__);
        }

        /* figure out the flow control settings */
        if (cflag & CRTSCTS) {
                config->wFlags |= UMP_MASK_UART_FLAGS_OUT_X_CTS_FLOW;
                config->wFlags |= UMP_MASK_UART_FLAGS_RTS_FLOW;
                dev_dbg(dev, "%s - RTS/CTS is enabled\n", __func__);
        } else {
                dev_dbg(dev, "%s - RTS/CTS is disabled\n", __func__);
                restart_read(edge_port);
        }

        /*
         * if we are implementing XON/XOFF, set the start and stop
         * character in the device
         */
        config->cXon  = START_CHAR(tty);
        config->cXoff = STOP_CHAR(tty);

        /* if we are implementing INBOUND XON/XOFF */
        if (I_IXOFF(tty)) {
                config->wFlags |= UMP_MASK_UART_FLAGS_IN_X;
                dev_dbg(dev, "%s - INBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n",
                        __func__, config->cXon, config->cXoff);
        } else
                dev_dbg(dev, "%s - INBOUND XON/XOFF is disabled\n", __func__);

        /* if we are implementing OUTBOUND XON/XOFF */
        if (I_IXON(tty)) {
                config->wFlags |= UMP_MASK_UART_FLAGS_OUT_X;
                dev_dbg(dev, "%s - OUTBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n",
                        __func__, config->cXon, config->cXoff);
        } else
                dev_dbg(dev, "%s - OUTBOUND XON/XOFF is disabled\n", __func__);

        tty->termios.c_cflag &= ~CMSPAR;

        /* Round the baud rate */
        baud = tty_get_baud_rate(tty);
        if (!baud) {
                /* pick a default, any default... */
                baud = 9600;
        } else {
                /* Avoid a zero divisor. */
                baud = min(baud, 461550);
                tty_encode_baud_rate(tty, baud, baud);
        }

        edge_port->baud_rate = baud;
        config->wBaudRate = (__u16)((461550L + baud/2) / baud);

        /* FIXME: Recompute actual baud from divisor here */

        dev_dbg(dev, "%s - baud rate = %d, wBaudRate = %d\n", __func__, baud, config->wBaudRate);

        dev_dbg(dev, "wBaudRate:   %d\n", (int)(461550L / config->wBaudRate));
        dev_dbg(dev, "wFlags:    0x%x\n", config->wFlags);
        dev_dbg(dev, "bDataBits:   %d\n", config->bDataBits);
        dev_dbg(dev, "bParity:     %d\n", config->bParity);
        dev_dbg(dev, "bStopBits:   %d\n", config->bStopBits);
        dev_dbg(dev, "cXon:        %d\n", config->cXon);
        dev_dbg(dev, "cXoff:       %d\n", config->cXoff);
        dev_dbg(dev, "bUartMode:   %d\n", config->bUartMode);

        /* move the word values into big endian mode */
        cpu_to_be16s(&config->wFlags);
        cpu_to_be16s(&config->wBaudRate);

        status = send_cmd(edge_port->port->serial->dev, UMPC_SET_CONFIG,
                                (__u8)(UMPM_UART1_PORT + port_number),
                                0, (__u8 *)config, sizeof(*config));
        if (status)
                dev_dbg(dev, "%s - error %d when trying to write config to device\n",
                        __func__, status);
        kfree(config);
}

static void edge_set_termios(struct tty_struct *tty,
                struct usb_serial_port *port, struct ktermios *old_termios)
{
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);

        if (edge_port == NULL)
                return;
        /* change the port settings to the new ones specified */
        change_port_settings(tty, edge_port, old_termios);
}

static int edge_tiocmset(struct tty_struct *tty,
                                        unsigned int set, unsigned int clear)
{
        struct usb_serial_port *port = tty->driver_data;
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        unsigned int mcr;
        unsigned long flags;

        spin_lock_irqsave(&edge_port->ep_lock, flags);
        mcr = edge_port->shadow_mcr;
        if (set & TIOCM_RTS)
                mcr |= MCR_RTS;
        if (set & TIOCM_DTR)
                mcr |= MCR_DTR;
        if (set & TIOCM_LOOP)
                mcr |= MCR_LOOPBACK;

        if (clear & TIOCM_RTS)
                mcr &= ~MCR_RTS;
        if (clear & TIOCM_DTR)
                mcr &= ~MCR_DTR;
        if (clear & TIOCM_LOOP)
                mcr &= ~MCR_LOOPBACK;

        edge_port->shadow_mcr = mcr;
        spin_unlock_irqrestore(&edge_port->ep_lock, flags);

        restore_mcr(edge_port, mcr);
        return 0;
}

static int edge_tiocmget(struct tty_struct *tty)
{
        struct usb_serial_port *port = tty->driver_data;
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        unsigned int result = 0;
        unsigned int msr;
        unsigned int mcr;
        unsigned long flags;

        spin_lock_irqsave(&edge_port->ep_lock, flags);

        msr = edge_port->shadow_msr;
        mcr = edge_port->shadow_mcr;
        result = ((mcr & MCR_DTR)       ? TIOCM_DTR: 0)   /* 0x002 */
                  | ((mcr & MCR_RTS)    ? TIOCM_RTS: 0)   /* 0x004 */
                  | ((msr & EDGEPORT_MSR_CTS)   ? TIOCM_CTS: 0)   /* 0x020 */
                  | ((msr & EDGEPORT_MSR_CD)    ? TIOCM_CAR: 0)   /* 0x040 */
                  | ((msr & EDGEPORT_MSR_RI)    ? TIOCM_RI:  0)   /* 0x080 */
                  | ((msr & EDGEPORT_MSR_DSR)   ? TIOCM_DSR: 0);  /* 0x100 */


        dev_dbg(&port->dev, "%s -- %x\n", __func__, result);
        spin_unlock_irqrestore(&edge_port->ep_lock, flags);

        return result;
}

static int get_serial_info(struct tty_struct *tty,
                                struct serial_struct *ss)
{
        struct usb_serial_port *port = tty->driver_data;
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        unsigned cwait;

        cwait = edge_port->port->port.closing_wait;
        if (cwait != ASYNC_CLOSING_WAIT_NONE)
                cwait = jiffies_to_msecs(cwait) / 10;

        ss->type                = PORT_16550A;
        ss->line                = edge_port->port->minor;
        ss->port                = edge_port->port->port_number;
        ss->irq                 = 0;
        ss->xmit_fifo_size      = edge_port->port->bulk_out_size;
        ss->baud_base           = 9600;
        ss->close_delay         = 5*HZ;
        ss->closing_wait        = cwait;
        return 0;
}

static void edge_break(struct tty_struct *tty, int break_state)
{
        struct usb_serial_port *port = tty->driver_data;
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        int status;
        int bv = 0;     /* Off */

        if (break_state == -1)
                bv = 1; /* On */
        status = ti_do_config(edge_port, UMPC_SET_CLR_BREAK, bv);
        if (status)
                dev_dbg(&port->dev, "%s - error %d sending break set/clear command.\n",
                        __func__, status);
}

static void edge_heartbeat_schedule(struct edgeport_serial *edge_serial)
{
        if (!edge_serial->use_heartbeat)
                return;

        schedule_delayed_work(&edge_serial->heartbeat_work,
                        FW_HEARTBEAT_SECS * HZ);
}

static void edge_heartbeat_work(struct work_struct *work)
{
        struct edgeport_serial *serial;
        struct ti_i2c_desc *rom_desc;

        serial = container_of(work, struct edgeport_serial,
                        heartbeat_work.work);

        rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL);

        /* Descriptor address request is enough to reset the firmware timer */
        if (!rom_desc || !get_descriptor_addr(serial, I2C_DESC_TYPE_ION,
                        rom_desc)) {
                dev_err(&serial->serial->interface->dev,
                                "%s - Incomplete heartbeat\n", __func__);
        }
        kfree(rom_desc);

        edge_heartbeat_schedule(serial);
}

static int edge_calc_num_ports(struct usb_serial *serial,
                                struct usb_serial_endpoints *epds)
{
        struct device *dev = &serial->interface->dev;
        unsigned char num_ports = serial->type->num_ports;

        /* Make sure we have the required endpoints when in download mode. */
        if (serial->interface->cur_altsetting->desc.bNumEndpoints > 1) {
                if (epds->num_bulk_in < num_ports ||
                                epds->num_bulk_out < num_ports ||
                                epds->num_interrupt_in < 1) {
                        dev_err(dev, "required endpoints missing\n");
                        return -ENODEV;
                }
        }

        return num_ports;
}

static int edge_startup(struct usb_serial *serial)
{
        struct edgeport_serial *edge_serial;
        int status;
        u16 product_id;

        /* create our private serial structure */
        edge_serial = kzalloc(sizeof(struct edgeport_serial), GFP_KERNEL);
        if (!edge_serial)
                return -ENOMEM;

        mutex_init(&edge_serial->es_lock);
        edge_serial->serial = serial;
        INIT_DELAYED_WORK(&edge_serial->heartbeat_work, edge_heartbeat_work);
        usb_set_serial_data(serial, edge_serial);

        status = download_fw(edge_serial);
        if (status < 0) {
                kfree(edge_serial);
                return status;
        }

        if (status > 0)
                return 1;       /* bind but do not register any ports */

        product_id = le16_to_cpu(
                        edge_serial->serial->dev->descriptor.idProduct);

        /* Currently only the EP/416 models require heartbeat support */
        if (edge_serial->fw_version > FW_HEARTBEAT_VERSION_CUTOFF) {
                if (product_id == ION_DEVICE_ID_TI_EDGEPORT_416 ||
                        product_id == ION_DEVICE_ID_TI_EDGEPORT_416B) {
                        edge_serial->use_heartbeat = true;
                }
        }

        edge_heartbeat_schedule(edge_serial);

        return 0;
}

static void edge_disconnect(struct usb_serial *serial)
{
        struct edgeport_serial *edge_serial = usb_get_serial_data(serial);

        cancel_delayed_work_sync(&edge_serial->heartbeat_work);
}

static void edge_release(struct usb_serial *serial)
{
        struct edgeport_serial *edge_serial = usb_get_serial_data(serial);

        cancel_delayed_work_sync(&edge_serial->heartbeat_work);
        kfree(edge_serial);
}

static int edge_port_probe(struct usb_serial_port *port)
{
        struct edgeport_port *edge_port;
        int ret;

        edge_port = kzalloc(sizeof(*edge_port), GFP_KERNEL);
        if (!edge_port)
                return -ENOMEM;

        spin_lock_init(&edge_port->ep_lock);
        edge_port->port = port;
        edge_port->edge_serial = usb_get_serial_data(port->serial);
        edge_port->bUartMode = default_uart_mode;

        switch (port->port_number) {
        case 0:
                edge_port->uart_base = UMPMEM_BASE_UART1;
                edge_port->dma_address = UMPD_OEDB1_ADDRESS;
                break;
        case 1:
                edge_port->uart_base = UMPMEM_BASE_UART2;
                edge_port->dma_address = UMPD_OEDB2_ADDRESS;
                break;
        default:
                dev_err(&port->dev, "unknown port number\n");
                ret = -ENODEV;
                goto err;
        }

        dev_dbg(&port->dev,
                "%s - port_number = %d, uart_base = %04x, dma_address = %04x\n",
                __func__, port->port_number, edge_port->uart_base,
                edge_port->dma_address);

        usb_set_serial_port_data(port, edge_port);

        ret = edge_create_sysfs_attrs(port);
        if (ret)
                goto err;

        port->port.closing_wait = msecs_to_jiffies(closing_wait * 10);
        port->port.drain_delay = 1;

        return 0;
err:
        kfree(edge_port);

        return ret;
}

static int edge_port_remove(struct usb_serial_port *port)
{
        struct edgeport_port *edge_port;

        edge_port = usb_get_serial_port_data(port);
        edge_remove_sysfs_attrs(port);
        kfree(edge_port);

        return 0;
}

/* Sysfs Attributes */

static ssize_t uart_mode_show(struct device *dev,
        struct device_attribute *attr, char *buf)
{
        struct usb_serial_port *port = to_usb_serial_port(dev);
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);

        return sprintf(buf, "%d\n", edge_port->bUartMode);
}

static ssize_t uart_mode_store(struct device *dev,
        struct device_attribute *attr, const char *valbuf, size_t count)
{
        struct usb_serial_port *port = to_usb_serial_port(dev);
        struct edgeport_port *edge_port = usb_get_serial_port_data(port);
        unsigned int v = simple_strtoul(valbuf, NULL, 0);

        dev_dbg(dev, "%s: setting uart_mode = %d\n", __func__, v);

        if (v < 256)
                edge_port->bUartMode = v;
        else
                dev_err(dev, "%s - uart_mode %d is invalid\n", __func__, v);

        return count;
}
static DEVICE_ATTR_RW(uart_mode);

static int edge_create_sysfs_attrs(struct usb_serial_port *port)
{
        return device_create_file(&port->dev, &dev_attr_uart_mode);
}

static int edge_remove_sysfs_attrs(struct usb_serial_port *port)
{
        device_remove_file(&port->dev, &dev_attr_uart_mode);
        return 0;
}

#ifdef CONFIG_PM
static int edge_suspend(struct usb_serial *serial, pm_message_t message)
{
        struct edgeport_serial *edge_serial = usb_get_serial_data(serial);

        cancel_delayed_work_sync(&edge_serial->heartbeat_work);

        return 0;
}

static int edge_resume(struct usb_serial *serial)
{
        struct edgeport_serial *edge_serial = usb_get_serial_data(serial);

        edge_heartbeat_schedule(edge_serial);

        return 0;
}
#endif

static struct usb_serial_driver edgeport_1port_device = {
        .driver = {
                .owner          = THIS_MODULE,
                .name           = "edgeport_ti_1",
        },
        .description            = "Edgeport TI 1 port adapter",
        .id_table               = edgeport_1port_id_table,
        .num_ports              = 1,
        .num_bulk_out           = 1,
        .open                   = edge_open,
        .close                  = edge_close,
        .throttle               = edge_throttle,
        .unthrottle             = edge_unthrottle,
        .attach                 = edge_startup,
        .calc_num_ports         = edge_calc_num_ports,
        .disconnect             = edge_disconnect,
        .release                = edge_release,
        .port_probe             = edge_port_probe,
        .port_remove            = edge_port_remove,
        .get_serial             = get_serial_info,
        .set_termios            = edge_set_termios,
        .tiocmget               = edge_tiocmget,
        .tiocmset               = edge_tiocmset,
        .tiocmiwait             = usb_serial_generic_tiocmiwait,
        .get_icount             = usb_serial_generic_get_icount,
        .write                  = edge_write,
        .write_room             = edge_write_room,
        .chars_in_buffer        = edge_chars_in_buffer,
        .tx_empty               = edge_tx_empty,
        .break_ctl              = edge_break,
        .read_int_callback      = edge_interrupt_callback,
        .read_bulk_callback     = edge_bulk_in_callback,
        .write_bulk_callback    = edge_bulk_out_callback,
#ifdef CONFIG_PM
        .suspend                = edge_suspend,
        .resume                 = edge_resume,
#endif
};

static struct usb_serial_driver edgeport_2port_device = {
        .driver = {
                .owner          = THIS_MODULE,
                .name           = "edgeport_ti_2",
        },
        .description            = "Edgeport TI 2 port adapter",
        .id_table               = edgeport_2port_id_table,
        .num_ports              = 2,
        .num_bulk_out           = 1,
        .open                   = edge_open,
        .close                  = edge_close,
        .throttle               = edge_throttle,
        .unthrottle             = edge_unthrottle,
        .attach                 = edge_startup,
        .calc_num_ports         = edge_calc_num_ports,
        .disconnect             = edge_disconnect,
        .release                = edge_release,
        .port_probe             = edge_port_probe,
        .port_remove            = edge_port_remove,
        .get_serial             = get_serial_info,
        .set_termios            = edge_set_termios,
        .tiocmget               = edge_tiocmget,
        .tiocmset               = edge_tiocmset,
        .tiocmiwait             = usb_serial_generic_tiocmiwait,
        .get_icount             = usb_serial_generic_get_icount,
        .write                  = edge_write,
        .write_room             = edge_write_room,
        .chars_in_buffer        = edge_chars_in_buffer,
        .tx_empty               = edge_tx_empty,
        .break_ctl              = edge_break,
        .read_int_callback      = edge_interrupt_callback,
        .read_bulk_callback     = edge_bulk_in_callback,
        .write_bulk_callback    = edge_bulk_out_callback,
#ifdef CONFIG_PM
        .suspend                = edge_suspend,
        .resume                 = edge_resume,
#endif
};

static struct usb_serial_driver * const serial_drivers[] = {
        &edgeport_1port_device, &edgeport_2port_device, NULL
};

module_usb_serial_driver(serial_drivers, id_table_combined);

MODULE_AUTHOR(DRIVER_AUTHOR);
MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");
MODULE_FIRMWARE("edgeport/down3.bin");

module_param(closing_wait, int, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(closing_wait, "Maximum wait for data to drain, in .01 secs");

module_param(ignore_cpu_rev, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(ignore_cpu_rev,
                        "Ignore the cpu revision when connecting to a device");

module_param(default_uart_mode, int, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(default_uart_mode, "Default uart_mode, 0=RS232, ...");