1
2
3
4
5
6
7
8
9#include <linux/errno.h>
10#include <linux/slab.h>
11#include <linux/tty.h>
12#include <linux/tty_driver.h>
13#include <linux/tty_flip.h>
14#include <linux/module.h>
15#include <linux/serial.h>
16#include <linux/usb.h>
17#include <linux/usb/serial.h>
18#include <linux/serial_reg.h>
19#include <linux/uaccess.h>
20
21#define QT_OPEN_CLOSE_CHANNEL 0xca
22#define QT_SET_GET_DEVICE 0xc2
23#define QT_SET_GET_REGISTER 0xc0
24#define QT_GET_SET_PREBUF_TRIG_LVL 0xcc
25#define QT_SET_ATF 0xcd
26#define QT_GET_SET_UART 0xc1
27#define QT_TRANSFER_IN 0xc0
28#define QT_HW_FLOW_CONTROL_MASK 0xc5
29#define QT_SW_FLOW_CONTROL_MASK 0xc6
30
31#define SERIAL_MSR_MASK 0xf0
32
33#define SERIAL_CRTSCTS ((UART_MCR_RTS << 8) | UART_MSR_CTS)
34
35#define SERIAL_EVEN_PARITY (UART_LCR_PARITY | UART_LCR_EPAR)
36
37#define MAX_BAUD_RATE 460800
38
39#define ATC_DISABLED 0x00
40#define DUPMODE_BITS 0xc0
41#define RR_BITS 0x03
42#define LOOPMODE_BITS 0x41
43#define RS232_MODE 0x00
44#define RTSCTS_TO_CONNECTOR 0x40
45#define CLKS_X4 0x02
46#define FULLPWRBIT 0x00000080
47#define NEXT_BOARD_POWER_BIT 0x00000004
48
49#define DRIVER_DESC "Quatech SSU-100 USB to Serial Driver"
50
51#define USB_VENDOR_ID_QUATECH 0x061d
52#define QUATECH_SSU100 0xC020
53
54static const struct usb_device_id id_table[] = {
55 {USB_DEVICE(USB_VENDOR_ID_QUATECH, QUATECH_SSU100)},
56 {}
57};
58MODULE_DEVICE_TABLE(usb, id_table);
59
60struct ssu100_port_private {
61 spinlock_t status_lock;
62 u8 shadowLSR;
63 u8 shadowMSR;
64};
65
66static inline int ssu100_control_msg(struct usb_device *dev,
67 u8 request, u16 data, u16 index)
68{
69 return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
70 request, 0x40, data, index,
71 NULL, 0, 300);
72}
73
74static inline int ssu100_setdevice(struct usb_device *dev, u8 *data)
75{
76 u16 x = ((u16)(data[1] << 8) | (u16)(data[0]));
77
78 return ssu100_control_msg(dev, QT_SET_GET_DEVICE, x, 0);
79}
80
81
82static inline int ssu100_getdevice(struct usb_device *dev, u8 *data)
83{
84 int ret;
85
86 ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
87 QT_SET_GET_DEVICE, 0xc0, 0, 0,
88 data, 3, 300);
89 if (ret < 3) {
90 if (ret >= 0)
91 ret = -EIO;
92 }
93
94 return ret;
95}
96
97static inline int ssu100_getregister(struct usb_device *dev,
98 unsigned short uart,
99 unsigned short reg,
100 u8 *data)
101{
102 int ret;
103
104 ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
105 QT_SET_GET_REGISTER, 0xc0, reg,
106 uart, data, sizeof(*data), 300);
107 if (ret < (int)sizeof(*data)) {
108 if (ret >= 0)
109 ret = -EIO;
110 }
111
112 return ret;
113}
114
115
116static inline int ssu100_setregister(struct usb_device *dev,
117 unsigned short uart,
118 unsigned short reg,
119 u16 data)
120{
121 u16 value = (data << 8) | reg;
122
123 return usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
124 QT_SET_GET_REGISTER, 0x40, value, uart,
125 NULL, 0, 300);
126
127}
128
129#define set_mctrl(dev, set) update_mctrl((dev), (set), 0)
130#define clear_mctrl(dev, clear) update_mctrl((dev), 0, (clear))
131
132
133static inline int update_mctrl(struct usb_device *dev, unsigned int set,
134 unsigned int clear)
135{
136 unsigned urb_value;
137 int result;
138
139 if (((set | clear) & (TIOCM_DTR | TIOCM_RTS)) == 0) {
140 dev_dbg(&dev->dev, "%s - DTR|RTS not being set|cleared\n", __func__);
141 return 0;
142 }
143
144 clear &= ~set;
145 urb_value = 0;
146 if (set & TIOCM_DTR)
147 urb_value |= UART_MCR_DTR;
148 if (set & TIOCM_RTS)
149 urb_value |= UART_MCR_RTS;
150
151 result = ssu100_setregister(dev, 0, UART_MCR, urb_value);
152 if (result < 0)
153 dev_dbg(&dev->dev, "%s Error from MODEM_CTRL urb\n", __func__);
154
155 return result;
156}
157
158static int ssu100_initdevice(struct usb_device *dev)
159{
160 u8 *data;
161 int result = 0;
162
163 data = kzalloc(3, GFP_KERNEL);
164 if (!data)
165 return -ENOMEM;
166
167 result = ssu100_getdevice(dev, data);
168 if (result < 0) {
169 dev_dbg(&dev->dev, "%s - get_device failed %i\n", __func__, result);
170 goto out;
171 }
172
173 data[1] &= ~FULLPWRBIT;
174
175 result = ssu100_setdevice(dev, data);
176 if (result < 0) {
177 dev_dbg(&dev->dev, "%s - setdevice failed %i\n", __func__, result);
178 goto out;
179 }
180
181 result = ssu100_control_msg(dev, QT_GET_SET_PREBUF_TRIG_LVL, 128, 0);
182 if (result < 0) {
183 dev_dbg(&dev->dev, "%s - set prebuffer level failed %i\n", __func__, result);
184 goto out;
185 }
186
187 result = ssu100_control_msg(dev, QT_SET_ATF, ATC_DISABLED, 0);
188 if (result < 0) {
189 dev_dbg(&dev->dev, "%s - set ATFprebuffer level failed %i\n", __func__, result);
190 goto out;
191 }
192
193 result = ssu100_getdevice(dev, data);
194 if (result < 0) {
195 dev_dbg(&dev->dev, "%s - get_device failed %i\n", __func__, result);
196 goto out;
197 }
198
199 data[0] &= ~(RR_BITS | DUPMODE_BITS);
200 data[0] |= CLKS_X4;
201 data[1] &= ~(LOOPMODE_BITS);
202 data[1] |= RS232_MODE;
203
204 result = ssu100_setdevice(dev, data);
205 if (result < 0) {
206 dev_dbg(&dev->dev, "%s - setdevice failed %i\n", __func__, result);
207 goto out;
208 }
209
210out: kfree(data);
211 return result;
212
213}
214
215
216static void ssu100_set_termios(struct tty_struct *tty,
217 struct usb_serial_port *port,
218 struct ktermios *old_termios)
219{
220 struct usb_device *dev = port->serial->dev;
221 struct ktermios *termios = &tty->termios;
222 u16 baud, divisor, remainder;
223 unsigned int cflag = termios->c_cflag;
224 u16 urb_value = 0;
225 int result;
226
227 if (cflag & PARENB) {
228 if (cflag & PARODD)
229 urb_value |= UART_LCR_PARITY;
230 else
231 urb_value |= SERIAL_EVEN_PARITY;
232 }
233
234 switch (cflag & CSIZE) {
235 case CS5:
236 urb_value |= UART_LCR_WLEN5;
237 break;
238 case CS6:
239 urb_value |= UART_LCR_WLEN6;
240 break;
241 case CS7:
242 urb_value |= UART_LCR_WLEN7;
243 break;
244 default:
245 case CS8:
246 urb_value |= UART_LCR_WLEN8;
247 break;
248 }
249
250 baud = tty_get_baud_rate(tty);
251 if (!baud)
252 baud = 9600;
253
254 dev_dbg(&port->dev, "%s - got baud = %d\n", __func__, baud);
255
256
257 divisor = MAX_BAUD_RATE / baud;
258 remainder = MAX_BAUD_RATE % baud;
259 if (((remainder * 2) >= baud) && (baud != 110))
260 divisor++;
261
262 urb_value = urb_value << 8;
263
264 result = ssu100_control_msg(dev, QT_GET_SET_UART, divisor, urb_value);
265 if (result < 0)
266 dev_dbg(&port->dev, "%s - set uart failed\n", __func__);
267
268 if (cflag & CRTSCTS)
269 result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
270 SERIAL_CRTSCTS, 0);
271 else
272 result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
273 0, 0);
274 if (result < 0)
275 dev_dbg(&port->dev, "%s - set HW flow control failed\n", __func__);
276
277 if (I_IXOFF(tty) || I_IXON(tty)) {
278 u16 x = ((u16)(START_CHAR(tty) << 8) | (u16)(STOP_CHAR(tty)));
279
280 result = ssu100_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
281 x, 0);
282 } else
283 result = ssu100_control_msg(dev, QT_SW_FLOW_CONTROL_MASK,
284 0, 0);
285
286 if (result < 0)
287 dev_dbg(&port->dev, "%s - set SW flow control failed\n", __func__);
288
289}
290
291
292static int ssu100_open(struct tty_struct *tty, struct usb_serial_port *port)
293{
294 struct usb_device *dev = port->serial->dev;
295 struct ssu100_port_private *priv = usb_get_serial_port_data(port);
296 u8 *data;
297 int result;
298 unsigned long flags;
299
300 data = kzalloc(2, GFP_KERNEL);
301 if (!data)
302 return -ENOMEM;
303
304 result = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
305 QT_OPEN_CLOSE_CHANNEL,
306 QT_TRANSFER_IN, 0x01,
307 0, data, 2, 300);
308 if (result < 2) {
309 dev_dbg(&port->dev, "%s - open failed %i\n", __func__, result);
310 if (result >= 0)
311 result = -EIO;
312 kfree(data);
313 return result;
314 }
315
316 spin_lock_irqsave(&priv->status_lock, flags);
317 priv->shadowLSR = data[0];
318 priv->shadowMSR = data[1];
319 spin_unlock_irqrestore(&priv->status_lock, flags);
320
321 kfree(data);
322
323
324 result = ssu100_control_msg(dev, QT_GET_SET_UART, 0x30, 0x0300);
325 if (result < 0)
326 dev_dbg(&port->dev, "%s - set uart failed\n", __func__);
327
328 if (tty)
329 ssu100_set_termios(tty, port, &tty->termios);
330
331 return usb_serial_generic_open(tty, port);
332}
333
334static int get_serial_info(struct tty_struct *tty,
335 struct serial_struct *ss)
336{
337 struct usb_serial_port *port = tty->driver_data;
338
339 ss->line = port->minor;
340 ss->port = 0;
341 ss->irq = 0;
342 ss->xmit_fifo_size = port->bulk_out_size;
343 ss->baud_base = 9600;
344 ss->close_delay = 5*HZ;
345 ss->closing_wait = 30*HZ;
346 return 0;
347}
348
349static int ssu100_attach(struct usb_serial *serial)
350{
351 return ssu100_initdevice(serial->dev);
352}
353
354static int ssu100_port_probe(struct usb_serial_port *port)
355{
356 struct ssu100_port_private *priv;
357
358 priv = kzalloc(sizeof(*priv), GFP_KERNEL);
359 if (!priv)
360 return -ENOMEM;
361
362 spin_lock_init(&priv->status_lock);
363
364 usb_set_serial_port_data(port, priv);
365
366 return 0;
367}
368
369static int ssu100_port_remove(struct usb_serial_port *port)
370{
371 struct ssu100_port_private *priv;
372
373 priv = usb_get_serial_port_data(port);
374 kfree(priv);
375
376 return 0;
377}
378
379static int ssu100_tiocmget(struct tty_struct *tty)
380{
381 struct usb_serial_port *port = tty->driver_data;
382 struct usb_device *dev = port->serial->dev;
383 u8 *d;
384 int r;
385
386 d = kzalloc(2, GFP_KERNEL);
387 if (!d)
388 return -ENOMEM;
389
390 r = ssu100_getregister(dev, 0, UART_MCR, d);
391 if (r < 0)
392 goto mget_out;
393
394 r = ssu100_getregister(dev, 0, UART_MSR, d+1);
395 if (r < 0)
396 goto mget_out;
397
398 r = (d[0] & UART_MCR_DTR ? TIOCM_DTR : 0) |
399 (d[0] & UART_MCR_RTS ? TIOCM_RTS : 0) |
400 (d[1] & UART_MSR_CTS ? TIOCM_CTS : 0) |
401 (d[1] & UART_MSR_DCD ? TIOCM_CAR : 0) |
402 (d[1] & UART_MSR_RI ? TIOCM_RI : 0) |
403 (d[1] & UART_MSR_DSR ? TIOCM_DSR : 0);
404
405mget_out:
406 kfree(d);
407 return r;
408}
409
410static int ssu100_tiocmset(struct tty_struct *tty,
411 unsigned int set, unsigned int clear)
412{
413 struct usb_serial_port *port = tty->driver_data;
414 struct usb_device *dev = port->serial->dev;
415
416 return update_mctrl(dev, set, clear);
417}
418
419static void ssu100_dtr_rts(struct usb_serial_port *port, int on)
420{
421 struct usb_device *dev = port->serial->dev;
422
423
424 if (!on) {
425 if (ssu100_setregister(dev, 0, UART_MCR, 0) < 0)
426 dev_err(&port->dev, "error from flowcontrol urb\n");
427 }
428
429 if (on)
430 set_mctrl(dev, TIOCM_DTR | TIOCM_RTS);
431 else
432 clear_mctrl(dev, TIOCM_DTR | TIOCM_RTS);
433}
434
435static void ssu100_update_msr(struct usb_serial_port *port, u8 msr)
436{
437 struct ssu100_port_private *priv = usb_get_serial_port_data(port);
438 unsigned long flags;
439
440 spin_lock_irqsave(&priv->status_lock, flags);
441 priv->shadowMSR = msr;
442 spin_unlock_irqrestore(&priv->status_lock, flags);
443
444 if (msr & UART_MSR_ANY_DELTA) {
445
446 if (msr & UART_MSR_DCTS)
447 port->icount.cts++;
448 if (msr & UART_MSR_DDSR)
449 port->icount.dsr++;
450 if (msr & UART_MSR_DDCD)
451 port->icount.dcd++;
452 if (msr & UART_MSR_TERI)
453 port->icount.rng++;
454 wake_up_interruptible(&port->port.delta_msr_wait);
455 }
456}
457
458static void ssu100_update_lsr(struct usb_serial_port *port, u8 lsr,
459 char *tty_flag)
460{
461 struct ssu100_port_private *priv = usb_get_serial_port_data(port);
462 unsigned long flags;
463
464 spin_lock_irqsave(&priv->status_lock, flags);
465 priv->shadowLSR = lsr;
466 spin_unlock_irqrestore(&priv->status_lock, flags);
467
468 *tty_flag = TTY_NORMAL;
469 if (lsr & UART_LSR_BRK_ERROR_BITS) {
470
471
472 if (lsr & UART_LSR_BI) {
473 port->icount.brk++;
474 *tty_flag = TTY_BREAK;
475 usb_serial_handle_break(port);
476 }
477 if (lsr & UART_LSR_PE) {
478 port->icount.parity++;
479 if (*tty_flag == TTY_NORMAL)
480 *tty_flag = TTY_PARITY;
481 }
482 if (lsr & UART_LSR_FE) {
483 port->icount.frame++;
484 if (*tty_flag == TTY_NORMAL)
485 *tty_flag = TTY_FRAME;
486 }
487 if (lsr & UART_LSR_OE) {
488 port->icount.overrun++;
489 tty_insert_flip_char(&port->port, 0, TTY_OVERRUN);
490 }
491 }
492
493}
494
495static void ssu100_process_read_urb(struct urb *urb)
496{
497 struct usb_serial_port *port = urb->context;
498 char *packet = (char *)urb->transfer_buffer;
499 char flag = TTY_NORMAL;
500 u32 len = urb->actual_length;
501 int i;
502 char *ch;
503
504 if ((len >= 4) &&
505 (packet[0] == 0x1b) && (packet[1] == 0x1b) &&
506 ((packet[2] == 0x00) || (packet[2] == 0x01))) {
507 if (packet[2] == 0x00)
508 ssu100_update_lsr(port, packet[3], &flag);
509 if (packet[2] == 0x01)
510 ssu100_update_msr(port, packet[3]);
511
512 len -= 4;
513 ch = packet + 4;
514 } else
515 ch = packet;
516
517 if (!len)
518 return;
519
520 if (port->port.console && port->sysrq) {
521 for (i = 0; i < len; i++, ch++) {
522 if (!usb_serial_handle_sysrq_char(port, *ch))
523 tty_insert_flip_char(&port->port, *ch, flag);
524 }
525 } else
526 tty_insert_flip_string_fixed_flag(&port->port, ch, flag, len);
527
528 tty_flip_buffer_push(&port->port);
529}
530
531static struct usb_serial_driver ssu100_device = {
532 .driver = {
533 .owner = THIS_MODULE,
534 .name = "ssu100",
535 },
536 .description = DRIVER_DESC,
537 .id_table = id_table,
538 .num_ports = 1,
539 .open = ssu100_open,
540 .attach = ssu100_attach,
541 .port_probe = ssu100_port_probe,
542 .port_remove = ssu100_port_remove,
543 .dtr_rts = ssu100_dtr_rts,
544 .process_read_urb = ssu100_process_read_urb,
545 .tiocmget = ssu100_tiocmget,
546 .tiocmset = ssu100_tiocmset,
547 .tiocmiwait = usb_serial_generic_tiocmiwait,
548 .get_icount = usb_serial_generic_get_icount,
549 .get_serial = get_serial_info,
550 .set_termios = ssu100_set_termios,
551};
552
553static struct usb_serial_driver * const serial_drivers[] = {
554 &ssu100_device, NULL
555};
556
557module_usb_serial_driver(serial_drivers, id_table);
558
559MODULE_DESCRIPTION(DRIVER_DESC);
560MODULE_LICENSE("GPL v2");
561
