/* SPDX-License-Identifier: GPL-2.0-only */
/*
 * Copyright (c) 2014-2018, NVIDIA CORPORATION.  All rights reserved.
 */

#ifndef _ABI_BPMP_ABI_H_
#define _ABI_BPMP_ABI_H_

#ifdef LK
#include <stdint.h>
#endif

#ifndef __ABI_PACKED
#define __ABI_PACKED __attribute__((packed))
#endif

#ifdef NO_GCC_EXTENSIONS
#define EMPTY char empty;
#define EMPTY_ARRAY 1
#else
#define EMPTY
#define EMPTY_ARRAY 0
#endif

#ifndef __UNION_ANON
#define __UNION_ANON
#endif
/**
 * @file
 */

/**
 * @defgroup MRQ MRQ Messages
 * @brief Messages sent to/from BPMP via IPC
 * @{
 *   @defgroup MRQ_Format Message Format
 *   @defgroup MRQ_Codes Message Request (MRQ) Codes
 *   @defgroup MRQ_Payloads Message Payloads
 *   @defgroup Error_Codes Error Codes
 * @}
 */

/**
 * @addtogroup MRQ_Format
 * @{
 * The CPU requests the BPMP to perform a particular service by
 * sending it an IVC frame containing a single MRQ message. An MRQ
 * message consists of a @ref mrq_request followed by a payload whose
 * format depends on mrq_request::mrq.
 *
 * The BPMP processes the data and replies with an IVC frame (on the
 * same IVC channel) containing and MRQ response. An MRQ response
 * consists of a @ref mrq_response followed by a payload whose format
 * depends on the associated mrq_request::mrq.
 *
 * A well-defined subset of the MRQ messages that the CPU sends to the
 * BPMP can lead to BPMP eventually sending an MRQ message to the
 * CPU. For example, when the CPU uses an #MRQ_THERMAL message to set
 * a thermal trip point, the BPMP may eventually send a single
 * #MRQ_THERMAL message of its own to the CPU indicating that the trip
 * point has been crossed.
 * @}
 */

/**
 * @ingroup MRQ_Format
 * @brief Header for an MRQ message
 *
 * Provides the MRQ number for the MRQ message: #mrq. The remainder of
 * the MRQ message is a payload (immediately following the
 * mrq_request) whose format depends on mrq.
 */
struct mrq_request {
        /** @brief MRQ number of the request */
        uint32_t mrq;
        /**
         * @brief Flags providing follow up directions to the receiver
         *
         * | Bit | Description                                |
         * |-----|--------------------------------------------|
         * | 1   | ring the sender's doorbell when responding |
         * | 0   | should be 1                                |
         */
        uint32_t flags;
} __ABI_PACKED;

/**
 * @ingroup MRQ_Format
 * @brief Header for an MRQ response
 *
 *  Provides an error code for the associated MRQ message. The
 *  remainder of the MRQ response is a payload (immediately following
 *  the mrq_response) whose format depends on the associated
 *  mrq_request::mrq
 */
struct mrq_response {
        /** @brief Error code for the MRQ request itself */
        int32_t err;
        /** @brief Reserved for future use */
        uint32_t flags;
} __ABI_PACKED;

/**
 * @ingroup MRQ_Format
 * Minimum needed size for an IPC message buffer
 */
#define MSG_MIN_SZ      128
/**
 * @ingroup MRQ_Format
 *  Minimum size guaranteed for data in an IPC message buffer
 */
#define MSG_DATA_MIN_SZ 120

/**
 * @ingroup MRQ_Codes
 * @name Legal MRQ codes
 * These are the legal values for mrq_request::mrq
 * @{
 */

#define MRQ_PING                0
#define MRQ_QUERY_TAG           1
#define MRQ_MODULE_LOAD         4
#define MRQ_MODULE_UNLOAD       5
#define MRQ_TRACE_MODIFY        7
#define MRQ_WRITE_TRACE         8
#define MRQ_THREADED_PING       9
#define MRQ_MODULE_MAIL         11
#define MRQ_DEBUGFS             19
#define MRQ_RESET               20
#define MRQ_I2C                 21
#define MRQ_CLK                 22
#define MRQ_QUERY_ABI           23
#define MRQ_PG_READ_STATE       25
#define MRQ_PG_UPDATE_STATE     26
#define MRQ_THERMAL             27
#define MRQ_CPU_VHINT           28
#define MRQ_ABI_RATCHET         29
#define MRQ_EMC_DVFS_LATENCY    31
#define MRQ_TRACE_ITER          64
#define MRQ_RINGBUF_CONSOLE     65
#define MRQ_PG                  66
#define MRQ_CPU_NDIV_LIMITS     67
#define MRQ_STRAP               68
#define MRQ_UPHY                69
#define MRQ_CPU_AUTO_CC3        70
#define MRQ_QUERY_FW_TAG        71
#define MRQ_FMON                72
#define MRQ_EC                  73
#define MRQ_FBVOLT_STATUS       74

/** @} */

/**
 * @ingroup MRQ_Codes
 * @brief Maximum MRQ code to be sent by CPU software to
 * BPMP. Subject to change in future
 */
#define MAX_CPU_MRQ_ID          74

/**
 * @addtogroup MRQ_Payloads
 * @{
 *   @defgroup Ping Ping
 *   @defgroup Query_Tag Query Tag
 *   @defgroup Module Loadable Modules
 *   @defgroup Trace Trace
 *   @defgroup Debugfs Debug File System
 *   @defgroup Reset Reset
 *   @defgroup I2C I2C
 *   @defgroup Clocks Clocks
 *   @defgroup ABI_info ABI Info
 *   @defgroup Powergating Power Gating
 *   @defgroup Thermal Thermal
 *   @defgroup Vhint CPU Voltage hint
 *   @defgroup EMC EMC
 *   @defgroup CPU NDIV Limits
 *   @defgroup RingbufConsole Ring Buffer Console
 *   @defgroup Strap Straps
 *   @defgroup UPHY UPHY
 *   @defgroup CC3 Auto-CC3
 *   @defgroup FMON FMON
 *   @defgroup EC EC
 *   @defgroup Fbvolt_status Fuse Burn Voltage Status
 * @}
 */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_PING
 * @brief A simple ping
 *
 * * Platforms: All
 * * Initiators: Any
 * * Targets: Any
 * * Request Payload: @ref mrq_ping_request
 * * Response Payload: @ref mrq_ping_response
 *
 * @ingroup MRQ_Codes
 * @def MRQ_THREADED_PING
 * @brief A deeper ping
 *
 * * Platforms: All
 * * Initiators: Any
 * * Targets: BPMP
 * * Request Payload: @ref mrq_ping_request
 * * Response Payload: @ref mrq_ping_response
 *
 * Behavior is equivalent to a simple #MRQ_PING except that BPMP
 * responds from a thread context (providing a slightly more robust
 * sign of life).
 *
 */

/**
 * @ingroup Ping
 * @brief Request with #MRQ_PING
 *
 * Used by the sender of an #MRQ_PING message to request a pong from
 * recipient. The response from the recipient is computed based on
 * #challenge.
 */
struct mrq_ping_request {
/** @brief Arbitrarily chosen value */
        uint32_t challenge;
} __ABI_PACKED;

/**
 * @ingroup Ping
 * @brief Response to #MRQ_PING
 *
 * Sent in response to an #MRQ_PING message. #reply should be the
 * mrq_ping_request challenge left shifted by 1 with the carry-bit
 * dropped.
 *
 */
struct mrq_ping_response {
        /** @brief Response to the MRQ_PING challege */
        uint32_t reply;
} __ABI_PACKED;

/**
 * @ingroup MRQ_Codes
 * @def MRQ_QUERY_TAG
 * @brief Query BPMP firmware's tag (i.e. unique identifer)
 *
 * @deprecated Use #MRQ_QUERY_FW_TAG instead.
 *
 * * Platforms: All
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_query_tag_request
 * * Response Payload: N/A
 *
 */

/**
 * @ingroup Query_Tag
 * @brief Request with #MRQ_QUERY_TAG
 *
 * @deprecated This structure will be removed in future version.
 * Use MRQ_QUERY_FW_TAG instead.
 */
struct mrq_query_tag_request {
  /** @brief Base address to store the firmware tag */
        uint32_t addr;
} __ABI_PACKED;


/**
 * @ingroup MRQ_Codes
 * @def MRQ_QUERY_FW_TAG
 * @brief Query BPMP firmware's tag (i.e. unique identifier)
 *
 * * Platforms: All
 * * Initiators: Any
 * * Targets: BPMP
 * * Request Payload: N/A
 * * Response Payload: @ref mrq_query_fw_tag_response
 *
 */

/**
 * @ingroup Query_Tag
 * @brief Response to #MRQ_QUERY_FW_TAG
 *
 * Sent in response to #MRQ_QUERY_FW_TAG message. #tag contains the unique
 * identifier for the version of firmware issuing the reply.
 *
 */
struct mrq_query_fw_tag_response {
  /** @brief Array to store tag information */
        uint8_t tag[32];
} __ABI_PACKED;

/**
 * @ingroup MRQ_Codes
 * @def MRQ_MODULE_LOAD
 * @brief Dynamically load a BPMP code module
 *
 * * Platforms: T210, T214, T186
 * @cond (bpmp_t210 || bpmp_t214 || bpmp_t186)
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_module_load_request
 * * Response Payload: @ref mrq_module_load_response
 *
 * @note This MRQ is disabled on production systems
 *
 */

/**
 * @ingroup Module
 * @brief Request with #MRQ_MODULE_LOAD
 *
 * Used by #MRQ_MODULE_LOAD calls to ask the recipient to dynamically
 * load the code located at #phys_addr and having size #size
 * bytes. #phys_addr is treated as a void pointer.
 *
 * The recipient copies the code from #phys_addr to locally allocated
 * memory prior to responding to this message.
 *
 * @todo document the module header format
 *
 * The sender is responsible for ensuring that the code is mapped in
 * the recipient's address map.
 *
 */
struct mrq_module_load_request {
        /** @brief Base address of the code to load. Treated as (void *) */
        uint32_t phys_addr; /* (void *) */
        /** @brief Size in bytes of code to load */
        uint32_t size;
} __ABI_PACKED;

/**
 * @ingroup Module
 * @brief Response to #MRQ_MODULE_LOAD
 *
 * @todo document mrq_response::err
 */
struct mrq_module_load_response {
        /** @brief Handle to the loaded module */
        uint32_t base;
} __ABI_PACKED;
/** @endcond*/

/**
 * @ingroup MRQ_Codes
 * @def MRQ_MODULE_UNLOAD
 * @brief Unload a previously loaded code module
 *
 * * Platforms: T210, T214, T186
 * @cond (bpmp_t210 || bpmp_t214 || bpmp_t186)
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_module_unload_request
 * * Response Payload: N/A
 *
 * @note This MRQ is disabled on production systems
 */

/**
 * @ingroup Module
 * @brief Request with #MRQ_MODULE_UNLOAD
 *
 * Used by #MRQ_MODULE_UNLOAD calls to request that a previously loaded
 * module be unloaded.
 */
struct mrq_module_unload_request {
        /** @brief Handle of the module to unload */
        uint32_t base;
} __ABI_PACKED;
/** @endcond*/

/**
 * @ingroup MRQ_Codes
 * @def MRQ_TRACE_MODIFY
 * @brief Modify the set of enabled trace events
 *
 * * Platforms: All
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_trace_modify_request
 * * Response Payload: @ref mrq_trace_modify_response
 *
 * @note This MRQ is disabled on production systems
 */

/**
 * @ingroup Trace
 * @brief Request with #MRQ_TRACE_MODIFY
 *
 * Used by %MRQ_TRACE_MODIFY calls to enable or disable specify trace
 * events.  #set takes precedence for any bit set in both #set and
 * #clr.
 */
struct mrq_trace_modify_request {
        /** @brief Bit mask of trace events to disable */
        uint32_t clr;
        /** @brief Bit mask of trace events to enable */
        uint32_t set;
} __ABI_PACKED;

/**
 * @ingroup Trace
 * @brief Response to #MRQ_TRACE_MODIFY
 *
 * Sent in repsonse to an #MRQ_TRACE_MODIFY message. #mask reflects the
 * state of which events are enabled after the recipient acted on the
 * message.
 *
 */
struct mrq_trace_modify_response {
        /** @brief Bit mask of trace event enable states */
        uint32_t mask;
} __ABI_PACKED;

/**
 * @ingroup MRQ_Codes
 * @def MRQ_WRITE_TRACE
 * @brief Write trace data to a buffer
 *
 * * Platforms: All
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_write_trace_request
 * * Response Payload: @ref mrq_write_trace_response
 *
 * mrq_response::err depends on the @ref mrq_write_trace_request field
 * values. err is -#BPMP_EINVAL if size is zero or area is NULL or
 * area is in an illegal range. A positive value for err indicates the
 * number of bytes written to area.
 *
 * @note This MRQ is disabled on production systems
 */

/**
 * @ingroup Trace
 * @brief Request with #MRQ_WRITE_TRACE
 *
 * Used by MRQ_WRITE_TRACE calls to ask the recipient to copy trace
 * data from the recipient's local buffer to the output buffer. #area
 * is treated as a byte-aligned pointer in the recipient's address
 * space.
 *
 * The sender is responsible for ensuring that the output
 * buffer is mapped in the recipient's address map. The recipient is
 * responsible for protecting its own code and data from accidental
 * overwrites.
 */
struct mrq_write_trace_request {
        /** @brief Base address of output buffer */
        uint32_t area;
        /** @brief Size in bytes of the output buffer */
        uint32_t size;
} __ABI_PACKED;

/**
 * @ingroup Trace
 * @brief Response to #MRQ_WRITE_TRACE
 *
 * Once this response is sent, the respondent will not access the
 * output buffer further.
 */
struct mrq_write_trace_response {
        /**
         * @brief Flag whether more data remains in local buffer
         *
         * Value is 1 if the entire local trace buffer has been
         * drained to the outputbuffer. Value is 0 otherwise.
         */
        uint32_t eof;
} __ABI_PACKED;

/** @private */
struct mrq_threaded_ping_request {
        uint32_t challenge;
} __ABI_PACKED;

/** @private */
struct mrq_threaded_ping_response {
        uint32_t reply;
} __ABI_PACKED;

/**
 * @ingroup MRQ_Codes
 * @def MRQ_MODULE_MAIL
 * @brief Send a message to a loadable module
 *
 * * Platforms: T210, T214, T186
 * @cond (bpmp_t210 || bpmp_t214 || bpmp_t186)
 * * Initiators: Any
 * * Targets: BPMP
 * * Request Payload: @ref mrq_module_mail_request
 * * Response Payload: @ref mrq_module_mail_response
 *
 * @note This MRQ is disabled on production systems
 */

/**
 * @ingroup Module
 * @brief Request with #MRQ_MODULE_MAIL
 */
struct mrq_module_mail_request {
        /** @brief Handle to the previously loaded module */
        uint32_t base;
        /** @brief Module-specific mail payload
         *
         * The length of data[ ] is unknown to the BPMP core firmware
         * but it is limited to the size of an IPC message.
         */
        uint8_t data[EMPTY_ARRAY];
} __ABI_PACKED;

/**
 * @ingroup Module
 * @brief Response to #MRQ_MODULE_MAIL
 */
struct mrq_module_mail_response {
        /** @brief Module-specific mail payload
         *
         * The length of data[ ] is unknown to the BPMP core firmware
         * but it is limited to the size of an IPC message.
         */
        uint8_t data[EMPTY_ARRAY];
} __ABI_PACKED;
/** @endcond */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_DEBUGFS
 * @brief Interact with BPMP's debugfs file nodes
 *
 * * Platforms: T186, T194
 * * Initiators: Any
 * * Targets: BPMP
 * * Request Payload: @ref mrq_debugfs_request
 * * Response Payload: @ref mrq_debugfs_response
 */

/**
 * @addtogroup Debugfs
 * @{
 *
 * The BPMP firmware implements a pseudo-filesystem called
 * debugfs. Any driver within the firmware may register with debugfs
 * to expose an arbitrary set of "files" in the filesystem. When
 * software on the CPU writes to a debugfs file, debugfs passes the
 * written data to a callback provided by the driver. When software on
 * the CPU reads a debugfs file, debugfs queries the driver for the
 * data to return to the CPU. The intention of the debugfs filesystem
 * is to provide information useful for debugging the system at
 * runtime.
 *
 * @note The files exposed via debugfs are not part of the
 * BPMP firmware's ABI. debugfs files may be added or removed in any
 * given version of the firmware. Typically the semantics of a debugfs
 * file are consistent from version to version but even that is not
 * guaranteed.
 *
 * @}
 */

/** @ingroup Debugfs */
enum mrq_debugfs_commands {
        /** @brief Perform read */
        CMD_DEBUGFS_READ = 1,
        /** @brief Perform write */
        CMD_DEBUGFS_WRITE = 2,
        /** @brief Perform dumping directory */
        CMD_DEBUGFS_DUMPDIR = 3,
        /** @brief Not a command */
        CMD_DEBUGFS_MAX
};

/**
 * @ingroup Debugfs
 * @brief Parameters for CMD_DEBUGFS_READ/WRITE command
 */
struct cmd_debugfs_fileop_request {
        /** @brief Physical address pointing at filename */
        uint32_t fnameaddr;
        /** @brief Length in bytes of filename buffer */
        uint32_t fnamelen;
        /** @brief Physical address pointing to data buffer */
        uint32_t dataaddr;
        /** @brief Length in bytes of data buffer */
        uint32_t datalen;
} __ABI_PACKED;

/**
 * @ingroup Debugfs
 * @brief Parameters for CMD_DEBUGFS_READ/WRITE command
 */
struct cmd_debugfs_dumpdir_request {
        /** @brief Physical address pointing to data buffer */
        uint32_t dataaddr;
        /** @brief Length in bytes of data buffer */
        uint32_t datalen;
} __ABI_PACKED;

/**
 * @ingroup Debugfs
 * @brief Response data for CMD_DEBUGFS_READ/WRITE command
 */
struct cmd_debugfs_fileop_response {
        /** @brief Always 0 */
        uint32_t reserved;
        /** @brief Number of bytes read from or written to data buffer */
        uint32_t nbytes;
} __ABI_PACKED;

/**
 * @ingroup Debugfs
 * @brief Response data for CMD_DEBUGFS_DUMPDIR command
 */
struct cmd_debugfs_dumpdir_response {
        /** @brief Always 0 */
        uint32_t reserved;
        /** @brief Number of bytes read from or written to data buffer */
        uint32_t nbytes;
} __ABI_PACKED;

/**
 * @ingroup Debugfs
 * @brief Request with #MRQ_DEBUGFS.
 *
 * The sender of an MRQ_DEBUGFS message uses #cmd to specify a debugfs
 * command to execute. Legal commands are the values of @ref
 * mrq_debugfs_commands. Each command requires a specific additional
 * payload of data.
 *
 * |command            |payload|
 * |-------------------|-------|
 * |CMD_DEBUGFS_READ   |fop    |
 * |CMD_DEBUGFS_WRITE  |fop    |
 * |CMD_DEBUGFS_DUMPDIR|dumpdir|
 */
struct mrq_debugfs_request {
        /** @brief Sub-command (@ref mrq_debugfs_commands) */
        uint32_t cmd;
        union {
                struct cmd_debugfs_fileop_request fop;
                struct cmd_debugfs_dumpdir_request dumpdir;
        } __UNION_ANON;
} __ABI_PACKED;

/**
 * @ingroup Debugfs
 */
struct mrq_debugfs_response {
        /** @brief Always 0 */
        int32_t reserved;
        union {
                /** @brief Response data for CMD_DEBUGFS_READ OR
                 * CMD_DEBUGFS_WRITE command
                 */
                struct cmd_debugfs_fileop_response fop;
                /** @brief Response data for CMD_DEBUGFS_DUMPDIR command */
                struct cmd_debugfs_dumpdir_response dumpdir;
        } __UNION_ANON;
} __ABI_PACKED;

/**
 * @addtogroup Debugfs
 * @{
 */
#define DEBUGFS_S_ISDIR (1 << 9)
#define DEBUGFS_S_IRUSR (1 << 8)
#define DEBUGFS_S_IWUSR (1 << 7)
/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_RESET
 * @brief Reset an IP block
 *
 * * Platforms: T186, T194
 * * Initiators: Any
 * * Targets: BPMP
 * * Request Payload: @ref mrq_reset_request
 * * Response Payload: @ref mrq_reset_response
 *
 * @addtogroup Reset
 * @{
 */

enum mrq_reset_commands {
        /** @brief Assert module reset */
        CMD_RESET_ASSERT = 1,
        /** @brief Deassert module reset */
        CMD_RESET_DEASSERT = 2,
        /** @brief Assert and deassert the module reset */
        CMD_RESET_MODULE = 3,
        /** @brief Get the highest reset ID */
        CMD_RESET_GET_MAX_ID = 4,
        /** @brief Not part of ABI and subject to change */
        CMD_RESET_MAX,
};

/**
 * @brief Request with MRQ_RESET
 *
 * Used by the sender of an #MRQ_RESET message to request BPMP to
 * assert or or deassert a given reset line.
 */
struct mrq_reset_request {
        /** @brief Reset action to perform (@ref mrq_reset_commands) */
        uint32_t cmd;
        /** @brief Id of the reset to affected */
        uint32_t reset_id;
} __ABI_PACKED;

/**
 * @brief Response for MRQ_RESET sub-command CMD_RESET_GET_MAX_ID. When
 * this sub-command is not supported, firmware will return -BPMP_EBADCMD
 * in mrq_response::err.
 */
struct cmd_reset_get_max_id_response {
        /** @brief Max reset id */
        uint32_t max_id;
} __ABI_PACKED;

/**
 * @brief Response with MRQ_RESET
 *
 * Each sub-command supported by @ref mrq_reset_request may return
 * sub-command-specific data. Some do and some do not as indicated
 * in the following table
 *
 * | sub-command          | payload          |
 * |----------------------|------------------|
 * | CMD_RESET_ASSERT     | -                |
 * | CMD_RESET_DEASSERT   | -                |
 * | CMD_RESET_MODULE     | -                |
 * | CMD_RESET_GET_MAX_ID | reset_get_max_id |
 */
struct mrq_reset_response {
        union {
                struct cmd_reset_get_max_id_response reset_get_max_id;
        } __UNION_ANON;
} __ABI_PACKED;

/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_I2C
 * @brief Issue an i2c transaction
 *
 * * Platforms: T186, T194
 * * Initiators: Any
 * * Targets: BPMP
 * * Request Payload: @ref mrq_i2c_request
 * * Response Payload: @ref mrq_i2c_response
 *
 * @addtogroup I2C
 * @{
 */
#define TEGRA_I2C_IPC_MAX_IN_BUF_SIZE   (MSG_DATA_MIN_SZ - 12)
#define TEGRA_I2C_IPC_MAX_OUT_BUF_SIZE  (MSG_DATA_MIN_SZ - 4)

#define SERIALI2C_TEN           0x0010
#define SERIALI2C_RD            0x0001
#define SERIALI2C_STOP          0x8000
#define SERIALI2C_NOSTART       0x4000
#define SERIALI2C_REV_DIR_ADDR  0x2000
#define SERIALI2C_IGNORE_NAK    0x1000
#define SERIALI2C_NO_RD_ACK     0x0800
#define SERIALI2C_RECV_LEN      0x0400

enum {
        CMD_I2C_XFER = 1
};

/**
 * @brief Serializable i2c request
 *
 * Instances of this structure are packed (little-endian) into
 * cmd_i2c_xfer_request::data_buf. Each instance represents a single
 * transaction (or a portion of a transaction with repeated starts) on
 * an i2c bus.
 *
 * Because these structures are packed, some instances are likely to
 * be misaligned. Additionally because #data is variable length, it is
 * not possible to iterate through a serialized list of these
 * structures without inspecting #len in each instance.  It may be
 * easier to serialize or deserialize cmd_i2c_xfer_request::data_buf
 * manually rather than using this structure definition.
*/
struct serial_i2c_request {
        /** @brief I2C slave address */
        uint16_t addr;
        /** @brief Bitmask of SERIALI2C_ flags */
        uint16_t flags;
        /** @brief Length of I2C transaction in bytes */
        uint16_t len;
        /** @brief For write transactions only, #len bytes of data */
        uint8_t data[];
} __ABI_PACKED;

/**
 * @brief Trigger one or more i2c transactions
 */
struct cmd_i2c_xfer_request {
        /** @brief Valid bus number from @ref bpmp_i2c_ids*/
        uint32_t bus_id;

        /** @brief Count of valid bytes in #data_buf*/
        uint32_t data_size;

        /** @brief Serialized packed instances of @ref serial_i2c_request*/
        uint8_t data_buf[TEGRA_I2C_IPC_MAX_IN_BUF_SIZE];
} __ABI_PACKED;

/**
 * @brief Container for data read from the i2c bus
 *
 * Processing an cmd_i2c_xfer_request::data_buf causes BPMP to execute
 * zero or more I2C reads. The data read from the bus is serialized
 * into #data_buf.
 */
struct cmd_i2c_xfer_response {
        /** @brief Count of valid bytes in #data_buf*/
        uint32_t data_size;
        /** @brief I2c read data */
        uint8_t data_buf[TEGRA_I2C_IPC_MAX_OUT_BUF_SIZE];
} __ABI_PACKED;

/**
 * @brief Request with #MRQ_I2C
 */
struct mrq_i2c_request {
        /** @brief Always CMD_I2C_XFER (i.e. 1) */
        uint32_t cmd;
        /** @brief Parameters of the transfer request */
        struct cmd_i2c_xfer_request xfer;
} __ABI_PACKED;

/**
 * @brief Response to #MRQ_I2C
 */
struct mrq_i2c_response {
        struct cmd_i2c_xfer_response xfer;
} __ABI_PACKED;

/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_CLK
 * @brief Perform a clock operation
 *
 * * Platforms: T186, T194
 * * Initiators: Any
 * * Targets: BPMP
 * * Request Payload: @ref mrq_clk_request
 * * Response Payload: @ref mrq_clk_response
 *
 * @addtogroup Clocks
 * @{
 */
enum {
        CMD_CLK_GET_RATE = 1,
        CMD_CLK_SET_RATE = 2,
        CMD_CLK_ROUND_RATE = 3,
        CMD_CLK_GET_PARENT = 4,
        CMD_CLK_SET_PARENT = 5,
        CMD_CLK_IS_ENABLED = 6,
        CMD_CLK_ENABLE = 7,
        CMD_CLK_DISABLE = 8,
        CMD_CLK_GET_ALL_INFO = 14,
        CMD_CLK_GET_MAX_CLK_ID = 15,
        CMD_CLK_GET_FMAX_AT_VMIN = 16,
        CMD_CLK_MAX,
};

#define BPMP_CLK_HAS_MUX        (1 << 0)
#define BPMP_CLK_HAS_SET_RATE   (1 << 1)
#define BPMP_CLK_IS_ROOT        (1 << 2)

#define MRQ_CLK_NAME_MAXLEN     40
#define MRQ_CLK_MAX_PARENTS     16

/** @private */
struct cmd_clk_get_rate_request {
        EMPTY
} __ABI_PACKED;

struct cmd_clk_get_rate_response {
        int64_t rate;
} __ABI_PACKED;

struct cmd_clk_set_rate_request {
        int32_t unused;
        int64_t rate;
} __ABI_PACKED;

struct cmd_clk_set_rate_response {
        int64_t rate;
} __ABI_PACKED;

struct cmd_clk_round_rate_request {
        int32_t unused;
        int64_t rate;
} __ABI_PACKED;

struct cmd_clk_round_rate_response {
        int64_t rate;
} __ABI_PACKED;

/** @private */
struct cmd_clk_get_parent_request {
        EMPTY
} __ABI_PACKED;

struct cmd_clk_get_parent_response {
        uint32_t parent_id;
} __ABI_PACKED;

struct cmd_clk_set_parent_request {
        uint32_t parent_id;
} __ABI_PACKED;

struct cmd_clk_set_parent_response {
        uint32_t parent_id;
} __ABI_PACKED;

/** @private */
struct cmd_clk_is_enabled_request {
        EMPTY
} __ABI_PACKED;

struct cmd_clk_is_enabled_response {
        int32_t state;
} __ABI_PACKED;

/** @private */
struct cmd_clk_enable_request {
        EMPTY
} __ABI_PACKED;

/** @private */
struct cmd_clk_enable_response {
        EMPTY
} __ABI_PACKED;

/** @private */
struct cmd_clk_disable_request {
        EMPTY
} __ABI_PACKED;

/** @private */
struct cmd_clk_disable_response {
        EMPTY
} __ABI_PACKED;

/** @private */
struct cmd_clk_get_all_info_request {
        EMPTY
} __ABI_PACKED;

struct cmd_clk_get_all_info_response {
        uint32_t flags;
        uint32_t parent;
        uint32_t parents[MRQ_CLK_MAX_PARENTS];
        uint8_t num_parents;
        uint8_t name[MRQ_CLK_NAME_MAXLEN];
} __ABI_PACKED;

/** @private */
struct cmd_clk_get_max_clk_id_request {
        EMPTY
} __ABI_PACKED;

struct cmd_clk_get_max_clk_id_response {
        uint32_t max_id;
} __ABI_PACKED;

/** @private */
struct cmd_clk_get_fmax_at_vmin_request {
        EMPTY
} __ABI_PACKED;

struct cmd_clk_get_fmax_at_vmin_response {
        int64_t rate;
} __ABI_PACKED;

/**
 * @ingroup Clocks
 * @brief Request with #MRQ_CLK
 *
 * Used by the sender of an #MRQ_CLK message to control clocks. The
 * clk_request is split into several sub-commands. Some sub-commands
 * require no additional data. Others have a sub-command specific
 * payload
 *
 * |sub-command                 |payload                |
 * |----------------------------|-----------------------|

 * |CMD_CLK_GET_RATE            |-                      |
 * |CMD_CLK_SET_RATE            |clk_set_rate           |
 * |CMD_CLK_ROUND_RATE          |clk_round_rate         |
 * |CMD_CLK_GET_PARENT          |-                      |
 * |CMD_CLK_SET_PARENT          |clk_set_parent         |
 * |CMD_CLK_IS_ENABLED          |-                      |
 * |CMD_CLK_ENABLE              |-                      |
 * |CMD_CLK_DISABLE             |-                      |
 * |CMD_CLK_GET_ALL_INFO        |-                      |
 * |CMD_CLK_GET_MAX_CLK_ID      |-                      |
 * |CMD_CLK_GET_FMAX_AT_VMIN    |-
 * |
 *
 */

struct mrq_clk_request {
        /** @brief Sub-command and clock id concatenated to 32-bit word.
         * - bits[31..24] is the sub-cmd.
         * - bits[23..0] is the clock id
         */
        uint32_t cmd_and_id;

        union {
                /** @private */
                struct cmd_clk_get_rate_request clk_get_rate;
                struct cmd_clk_set_rate_request clk_set_rate;
                struct cmd_clk_round_rate_request clk_round_rate;
                /** @private */
                struct cmd_clk_get_parent_request clk_get_parent;
                struct cmd_clk_set_parent_request clk_set_parent;
                /** @private */
                struct cmd_clk_enable_request clk_enable;
                /** @private */
                struct cmd_clk_disable_request clk_disable;
                /** @private */
                struct cmd_clk_is_enabled_request clk_is_enabled;
                /** @private */
                struct cmd_clk_get_all_info_request clk_get_all_info;
                /** @private */
                struct cmd_clk_get_max_clk_id_request clk_get_max_clk_id;
                /** @private */
                struct cmd_clk_get_fmax_at_vmin_request clk_get_fmax_at_vmin;
        } __UNION_ANON;
} __ABI_PACKED;

/**
 * @ingroup Clocks
 * @brief Response to MRQ_CLK
 *
 * Each sub-command supported by @ref mrq_clk_request may return
 * sub-command-specific data. Some do and some do not as indicated in
 * the following table
 *
 * |sub-command                 |payload                 |
 * |----------------------------|------------------------|
 * |CMD_CLK_GET_RATE            |clk_get_rate            |
 * |CMD_CLK_SET_RATE            |clk_set_rate            |
 * |CMD_CLK_ROUND_RATE          |clk_round_rate          |
 * |CMD_CLK_GET_PARENT          |clk_get_parent          |
 * |CMD_CLK_SET_PARENT          |clk_set_parent          |
 * |CMD_CLK_IS_ENABLED          |clk_is_enabled          |
 * |CMD_CLK_ENABLE              |-                       |
 * |CMD_CLK_DISABLE             |-                       |
 * |CMD_CLK_GET_ALL_INFO        |clk_get_all_info        |
 * |CMD_CLK_GET_MAX_CLK_ID      |clk_get_max_id          |
 * |CMD_CLK_GET_FMAX_AT_VMIN    |clk_get_fmax_at_vmin    |
 *
 */

struct mrq_clk_response {
        union {
                struct cmd_clk_get_rate_response clk_get_rate;
                struct cmd_clk_set_rate_response clk_set_rate;
                struct cmd_clk_round_rate_response clk_round_rate;
                struct cmd_clk_get_parent_response clk_get_parent;
                struct cmd_clk_set_parent_response clk_set_parent;
                /** @private */
                struct cmd_clk_enable_response clk_enable;
                /** @private */
                struct cmd_clk_disable_response clk_disable;
                struct cmd_clk_is_enabled_response clk_is_enabled;
                struct cmd_clk_get_all_info_response clk_get_all_info;
                struct cmd_clk_get_max_clk_id_response clk_get_max_clk_id;
                struct cmd_clk_get_fmax_at_vmin_response clk_get_fmax_at_vmin;
        } __UNION_ANON;
} __ABI_PACKED;

/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_QUERY_ABI
 * @brief Check if an MRQ is implemented
 *
 * * Platforms: All
 * * Initiators: Any
 * * Targets: Any except DMCE
 * * Request Payload: @ref mrq_query_abi_request
 * * Response Payload: @ref mrq_query_abi_response
 */

/**
 * @ingroup ABI_info
 * @brief Request with MRQ_QUERY_ABI
 *
 * Used by #MRQ_QUERY_ABI call to check if MRQ code #mrq is supported
 * by the recipient.
 */
struct mrq_query_abi_request {
        /** @brief MRQ code to query */
        uint32_t mrq;
} __ABI_PACKED;

/**
 * @ingroup ABI_info
 * @brief Response to MRQ_QUERY_ABI
 *
 * @note mrq_response::err of 0 indicates that the query was
 * successful, not that the MRQ itself is supported!
 */
struct mrq_query_abi_response {
        /** @brief 0 if queried MRQ is supported. Else, -#BPMP_ENODEV */
        int32_t status;
} __ABI_PACKED;

/**
 * @ingroup MRQ_Codes
 * @def MRQ_PG_READ_STATE
 * @brief Read the power-gating state of a partition
 *
 * * Platforms: T186
 * @cond bpmp_t186
 * * Initiators: Any
 * * Targets: BPMP
 * * Request Payload: @ref mrq_pg_read_state_request
 * * Response Payload: @ref mrq_pg_read_state_response
 */

/**
 * @ingroup Powergating
 * @brief Request with #MRQ_PG_READ_STATE
 *
 * Used by MRQ_PG_READ_STATE call to read the current state of a
 * partition.
 */
struct mrq_pg_read_state_request {
        /** @brief ID of partition */
        uint32_t partition_id;
} __ABI_PACKED;

/**
 * @ingroup Powergating
 * @brief Response to MRQ_PG_READ_STATE
 * @todo define possible errors.
 */
struct mrq_pg_read_state_response {
        /** @brief Read as don't care */
        uint32_t sram_state;
        /** @brief State of power partition
         * * 0 : off
         * * 1 : on
         */
        uint32_t logic_state;
} __ABI_PACKED;
/** @endcond*/
/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_PG_UPDATE_STATE
 * @brief Modify the power-gating state of a partition. In contrast to
 * MRQ_PG calls, the operations that change state (on/off) of power
 * partition are reference counted.
 *
 * * Platforms: T186
 * @cond bpmp_t186
 * * Initiators: Any
 * * Targets: BPMP
 * * Request Payload: @ref mrq_pg_update_state_request
 * * Response Payload: N/A
 */

/**
 * @ingroup Powergating
 * @brief Request with mrq_pg_update_state_request
 *
 * Used by #MRQ_PG_UPDATE_STATE call to request BPMP to change the
 * state of a power partition #partition_id.
 */
struct mrq_pg_update_state_request {
        /** @brief ID of partition */
        uint32_t partition_id;
        /** @brief Secondary control of power partition
         *  @details Ignored by many versions of the BPMP
         *  firmware. For maximum compatibility, set the value
         *  according to @ref logic_state
         * *  0x1: power ON partition (@ref logic_state == 0x3)
         * *  0x3: power OFF partition (@ref logic_state == 0x1)
         */
        uint32_t sram_state;
        /** @brief Controls state of power partition, legal values are
         * *  0x1 : power OFF partition
         * *  0x3 : power ON partition
         */
        uint32_t logic_state;
        /** @brief Change state of clocks of the power partition, legal values
         * *  0x0 : do not change clock state
         * *  0x1 : disable partition clocks (only applicable when
         *          @ref logic_state == 0x1)
         * *  0x3 : enable partition clocks (only applicable when
         *          @ref logic_state == 0x3)
         */
        uint32_t clock_state;
} __ABI_PACKED;
/** @endcond*/

/**
 * @ingroup MRQ_Codes
 * @def MRQ_PG
 * @brief Control power-gating state of a partition. In contrast to
 * MRQ_PG_UPDATE_STATE, operations that change the power partition
 * state are NOT reference counted
 *
 * @note BPMP-FW forcefully turns off some partitions as part of SC7 entry
 * because their state cannot be adequately restored on exit. Therefore,
 * it is recommended to power off all domains via MRQ_PG prior to SC7 entry.
 * See @ref bpmp_pdomain_ids for further detail.
 *
 * * Platforms: T186, T194
 * * Initiators: Any
 * * Targets: BPMP
 * * Request Payload: @ref mrq_pg_request
 * * Response Payload: @ref mrq_pg_response
 *
 * @addtogroup Powergating
 * @{
 */
enum mrq_pg_cmd {
        /**
         * @brief Check whether the BPMP driver supports the specified
         * request type
         *
         * mrq_response::err is 0 if the specified request is
         * supported and -#BPMP_ENODEV otherwise.
         */
        CMD_PG_QUERY_ABI = 0,

        /**
         * @brief Set the current state of specified power domain. The
         * possible values for power domains are defined in enum
         * pg_states
         *
         * mrq_response:err is
         * 0: Success
         * -#BPMP_EINVAL: Invalid request parameters
         */
        CMD_PG_SET_STATE = 1,

        /**
         * @brief Get the current state of specified power domain. The
         * possible values for power domains are defined in enum
         * pg_states
         *
         * mrq_response:err is
         * 0: Success
         * -#BPMP_EINVAL: Invalid request parameters
         */
        CMD_PG_GET_STATE = 2,

        /**
         * @brief Get the name string of specified power domain id.
         *
         * mrq_response:err is
         * 0: Success
         * -#BPMP_EINVAL: Invalid request parameters
         */
        CMD_PG_GET_NAME = 3,


        /**
         * @brief Get the highest power domain id in the system. Not
         * all IDs between 0 and max_id are valid IDs.
         *
         * mrq_response:err is
         * 0: Success
         * -#BPMP_EINVAL: Invalid request parameters
         */
        CMD_PG_GET_MAX_ID = 4,
};

#define MRQ_PG_NAME_MAXLEN      40

enum pg_states {
        /** @brief Power domain is OFF */
        PG_STATE_OFF = 0,
        /** @brief Power domain is ON */
        PG_STATE_ON = 1,
        /**
         * @brief a legacy state where power domain and the clock
         * associated to the domain are ON.
         * This state is only supported in T186, and the use of it is
         * deprecated.
         */
        PG_STATE_RUNNING = 2,
};

struct cmd_pg_query_abi_request {
        /** @ref mrq_pg_cmd */
        uint32_t type;
} __ABI_PACKED;

struct cmd_pg_set_state_request {
        /** @ref pg_states */
        uint32_t state;
} __ABI_PACKED;

struct cmd_pg_get_state_response {
        /** @ref pg_states */
        uint32_t state;
} __ABI_PACKED;

struct cmd_pg_get_name_response {
        uint8_t name[MRQ_PG_NAME_MAXLEN];
} __ABI_PACKED;

struct cmd_pg_get_max_id_response {
        uint32_t max_id;
} __ABI_PACKED;

/**
 * @brief Request with #MRQ_PG
 *
 * Used by the sender of an #MRQ_PG message to control power
 * partitions. The pg_request is split into several sub-commands. Some
 * sub-commands require no additional data. Others have a sub-command
 * specific payload
 *
 * |sub-command                 |payload                |
 * |----------------------------|-----------------------|
 * |CMD_PG_QUERY_ABI            | query_abi             |
 * |CMD_PG_SET_STATE            | set_state             |
 * |CMD_PG_GET_STATE            | -                     |
 * |CMD_PG_GET_NAME             | -                     |
 * |CMD_PG_GET_MAX_ID           | -                     |
 *
 */
struct mrq_pg_request {
        uint32_t cmd;
        uint32_t id;
        union {
                struct cmd_pg_query_abi_request query_abi;
                struct cmd_pg_set_state_request set_state;
        } __UNION_ANON;
} __ABI_PACKED;

/**
 * @brief Response to MRQ_PG
 *
 * Each sub-command supported by @ref mrq_pg_request may return
 * sub-command-specific data. Some do and some do not as indicated in
 * the following table
 *
 * |sub-command                 |payload                |
 * |----------------------------|-----------------------|
 * |CMD_PG_QUERY_ABI            | -                     |
 * |CMD_PG_SET_STATE            | -                     |
 * |CMD_PG_GET_STATE            | get_state             |
 * |CMD_PG_GET_NAME             | get_name              |
 * |CMD_PG_GET_MAX_ID           | get_max_id            |
 */
struct mrq_pg_response {
        union {
                struct cmd_pg_get_state_response get_state;
                struct cmd_pg_get_name_response get_name;
                struct cmd_pg_get_max_id_response get_max_id;
        } __UNION_ANON;
} __ABI_PACKED;

/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_THERMAL
 * @brief Interact with BPMP thermal framework
 *
 * * Platforms: T186, T194
 * * Initiators: Any
 * * Targets: Any
 * * Request Payload: TODO
 * * Response Payload: TODO
 *
 * @addtogroup Thermal
 *
 * The BPMP firmware includes a thermal framework. Drivers within the
 * bpmp firmware register with the framework to provide thermal
 * zones. Each thermal zone corresponds to an entity whose temperature
 * can be measured. The framework also has a notion of trip points. A
 * trip point consists of a thermal zone id, a temperature, and a
 * callback routine. The framework invokes the callback when the zone
 * hits the indicated temperature. The BPMP firmware uses this thermal
 * framework interally to implement various temperature-dependent
 * functions.
 *
 * Software on the CPU can use #MRQ_THERMAL (with payload @ref
 * mrq_thermal_host_to_bpmp_request) to interact with the BPMP thermal
 * framework. The CPU must It can query the number of supported zones,
 * query zone temperatures, and set trip points.
 *
 * When a trip point set by the CPU gets crossed, BPMP firmware issues
 * an IPC to the CPU having mrq_request::mrq = #MRQ_THERMAL and a
 * payload of @ref mrq_thermal_bpmp_to_host_request.
 * @{
 */
enum mrq_thermal_host_to_bpmp_cmd {
        /**
         * @brief Check whether the BPMP driver supports the specified
         * request type.
         *
         * Host needs to supply request parameters.
         *
         * mrq_response::err is 0 if the specified request is
         * supported and -#BPMP_ENODEV otherwise.
         */
        CMD_THERMAL_QUERY_ABI = 0,

        /**
         * @brief Get the current temperature of the specified zone.
         *
         * Host needs to supply request parameters.
         *
         * mrq_response::err is
         * *  0: Temperature query succeeded.
         * *  -#BPMP_EINVAL: Invalid request parameters.
         * *  -#BPMP_ENOENT: No driver registered for thermal zone..
         * *  -#BPMP_EFAULT: Problem reading temperature measurement.
         */
        CMD_THERMAL_GET_TEMP = 1,

        /**
         * @brief Enable or disable and set the lower and upper
         *   thermal limits for a thermal trip point. Each zone has
         *   one trip point.
         *
         * Host needs to supply request parameters. Once the
         * temperature hits a trip point, the BPMP will send a message
         * to the CPU having MRQ=MRQ_THERMAL and
         * type=CMD_THERMAL_HOST_TRIP_REACHED
         *
         * mrq_response::err is
         * *  0: Trip successfully set.
         * *  -#BPMP_EINVAL: Invalid request parameters.
         * *  -#BPMP_ENOENT: No driver registered for thermal zone.
         * *  -#BPMP_EFAULT: Problem setting trip point.
         */
        CMD_THERMAL_SET_TRIP = 2,

        /**
         * @brief Get the number of supported thermal zones.
         *
         * No request parameters required.
         *
         * mrq_response::err is always 0, indicating success.
         */
        CMD_THERMAL_GET_NUM_ZONES = 3,

        /** @brief: number of supported host-to-bpmp commands. May
         * increase in future
         */
        CMD_THERMAL_HOST_TO_BPMP_NUM
};

enum mrq_thermal_bpmp_to_host_cmd {
        /**
         * @brief Indication that the temperature for a zone has
         *   exceeded the range indicated in the thermal trip point
         *   for the zone.
         *
         * BPMP needs to supply request parameters. Host only needs to
         * acknowledge.
         */
        CMD_THERMAL_HOST_TRIP_REACHED = 100,

        /** @brief: number of supported bpmp-to-host commands. May
         * increase in future
         */
        CMD_THERMAL_BPMP_TO_HOST_NUM
};

/*
 * Host->BPMP request data for request type CMD_THERMAL_QUERY_ABI
 *
 * zone: Request type for which to check existence.
 */
struct cmd_thermal_query_abi_request {
        uint32_t type;
} __ABI_PACKED;

/*
 * Host->BPMP request data for request type CMD_THERMAL_GET_TEMP
 *
 * zone: Number of thermal zone.
 */
struct cmd_thermal_get_temp_request {
        uint32_t zone;
} __ABI_PACKED;

/*
 * BPMP->Host reply data for request CMD_THERMAL_GET_TEMP
 *
 * error: 0 if request succeeded.
 *      -BPMP_EINVAL if request parameters were invalid.
 *      -BPMP_ENOENT if no driver was registered for the specified thermal zone.
 *      -BPMP_EFAULT for other thermal zone driver errors.
 * temp: Current temperature in millicelsius.
 */
struct cmd_thermal_get_temp_response {
        int32_t temp;
} __ABI_PACKED;

/*
 * Host->BPMP request data for request type CMD_THERMAL_SET_TRIP
 *
 * zone: Number of thermal zone.
 * low: Temperature of lower trip point in millicelsius
 * high: Temperature of upper trip point in millicelsius
 * enabled: 1 to enable trip point, 0 to disable trip point
 */
struct cmd_thermal_set_trip_request {
        uint32_t zone;
        int32_t low;
        int32_t high;
        uint32_t enabled;
} __ABI_PACKED;

/*
 * BPMP->Host request data for request type CMD_THERMAL_HOST_TRIP_REACHED
 *
 * zone: Number of thermal zone where trip point was reached.
 */
struct cmd_thermal_host_trip_reached_request {
        uint32_t zone;
} __ABI_PACKED;

/*
 * BPMP->Host reply data for request type CMD_THERMAL_GET_NUM_ZONES
 *
 * num: Number of supported thermal zones. The thermal zones are indexed
 *      starting from zero.
 */
struct cmd_thermal_get_num_zones_response {
        uint32_t num;
} __ABI_PACKED;

/*
 * Host->BPMP request data.
 *
 * Reply type is union mrq_thermal_bpmp_to_host_response.
 *
 * type: Type of request. Values listed in enum mrq_thermal_type.
 * data: Request type specific parameters.
 */
struct mrq_thermal_host_to_bpmp_request {
        uint32_t type;
        union {
                struct cmd_thermal_query_abi_request query_abi;
                struct cmd_thermal_get_temp_request get_temp;
                struct cmd_thermal_set_trip_request set_trip;
        } __UNION_ANON;
} __ABI_PACKED;

/*
 * BPMP->Host request data.
 *
 * type: Type of request. Values listed in enum mrq_thermal_type.
 * data: Request type specific parameters.
 */
struct mrq_thermal_bpmp_to_host_request {
        uint32_t type;
        union {
                struct cmd_thermal_host_trip_reached_request host_trip_reached;
        } __UNION_ANON;
} __ABI_PACKED;

/*
 * Data in reply to a Host->BPMP request.
 */
union mrq_thermal_bpmp_to_host_response {
        struct cmd_thermal_get_temp_response get_temp;
        struct cmd_thermal_get_num_zones_response get_num_zones;
} __ABI_PACKED;
/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_CPU_VHINT
 * @brief Query CPU voltage hint data
 *
 * * Platforms: T186
 * @cond bpmp_t186
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_cpu_vhint_request
 * * Response Payload: N/A
 *
 * @addtogroup Vhint
 * @{
 */

/**
 * @brief Request with #MRQ_CPU_VHINT
 *
 * Used by #MRQ_CPU_VHINT call by CCPLEX to retrieve voltage hint data
 * from BPMP to memory space pointed by #addr. CCPLEX is responsible
 * to allocate sizeof(cpu_vhint_data) sized block of memory and
 * appropriately map it for BPMP before sending the request.
 */
struct mrq_cpu_vhint_request {
        /** @brief IOVA address for the #cpu_vhint_data */
        uint32_t addr;
        /** @brief ID of the cluster whose data is requested */
        uint32_t cluster_id;
} __ABI_PACKED;

/**
 * @brief Description of the CPU v/f relation
 *
 * Used by #MRQ_CPU_VHINT call to carry data pointed by
 * #mrq_cpu_vhint_request::addr
 */
struct cpu_vhint_data {
        uint32_t ref_clk_hz; /**< reference frequency in Hz */
        uint16_t pdiv; /**< post divider value */
        uint16_t mdiv; /**< input divider value */
        uint16_t ndiv_max; /**< fMAX expressed with max NDIV value */
        /** table of ndiv values as a function of vINDEX (voltage index) */
        uint16_t ndiv[80];
        /** minimum allowed NDIV value */
        uint16_t ndiv_min;
        /** minimum allowed voltage hint value (as in vINDEX) */
        uint16_t vfloor;
        /** maximum allowed voltage hint value (as in vINDEX) */
        uint16_t vceil;
        /** post-multiplier for vindex value */
        uint16_t vindex_mult;
        /** post-divider for vindex value */
        uint16_t vindex_div;
        /** reserved for future use */
        uint16_t reserved[328];
} __ABI_PACKED;
/** @endcond */
/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_ABI_RATCHET
 * @brief ABI ratchet value query
 *
 * * Platforms: T186, T194
 * * Initiators: Any
 * * Targets: BPMP
 * * Request Payload: @ref mrq_abi_ratchet_request
 * * Response Payload: @ref mrq_abi_ratchet_response
 * @addtogroup ABI_info
 * @{
 */

/**
 * @brief An ABI compatibility mechanism
 *
 * BPMP_ABI_RATCHET_VALUE may increase for various reasons in a future
 * revision of this header file.
 * 1. That future revision deprecates some MRQ
 * 2. That future revision introduces a breaking change to an existing
 *    MRQ or
 * 3. A bug is discovered in an existing implementation of the BPMP-FW
 *    (or possibly one of its clients) which warrants deprecating that
 *    implementation.
 */
#define BPMP_ABI_RATCHET_VALUE 3

/**
 * @brief Request with #MRQ_ABI_RATCHET.
 *
 * #ratchet should be #BPMP_ABI_RATCHET_VALUE from the ABI header
 * against which the requester was compiled.
 *
 * If ratchet is less than BPMP's #BPMP_ABI_RATCHET_VALUE, BPMP may
 * reply with mrq_response::err = -#BPMP_ERANGE to indicate that
 * BPMP-FW cannot interoperate correctly with the requester. Requester
 * should cease further communication with BPMP.
 *
 * Otherwise, err shall be 0.
 */
struct mrq_abi_ratchet_request {
        /** @brief Requester's ratchet value */
        uint16_t ratchet;
};

/**
 * @brief Response to #MRQ_ABI_RATCHET
 *
 * #ratchet shall be #BPMP_ABI_RATCHET_VALUE from the ABI header
 * against which BPMP firwmare was compiled.
 *
 * If #ratchet is less than the requester's #BPMP_ABI_RATCHET_VALUE,
 * the requster must either interoperate with BPMP according to an ABI
 * header version with BPMP_ABI_RATCHET_VALUE = ratchet or cease
 * communication with BPMP.
 *
 * If mrq_response::err is 0 and ratchet is greater than or equal to the
 * requester's BPMP_ABI_RATCHET_VALUE, the requester should continue
 * normal operation.
 */
struct mrq_abi_ratchet_response {
        /** @brief BPMP's ratchet value */
        uint16_t ratchet;
};
/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_EMC_DVFS_LATENCY
 * @brief Query frequency dependent EMC DVFS latency
 *
 * * Platforms: T186, T194
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: N/A
 * * Response Payload: @ref mrq_emc_dvfs_latency_response
 * @addtogroup EMC
 * @{
 */

/**
 * @brief Used by @ref mrq_emc_dvfs_latency_response
 */
struct emc_dvfs_latency {
        /** @brief EMC frequency in kHz */
        uint32_t freq;
        /** @brief EMC DVFS latency in nanoseconds */
        uint32_t latency;
} __ABI_PACKED;

#define EMC_DVFS_LATENCY_MAX_SIZE       14
/**
 * @brief Response to #MRQ_EMC_DVFS_LATENCY
 */
struct mrq_emc_dvfs_latency_response {
        /** @brief The number valid entries in #pairs */
        uint32_t num_pairs;
        /** @brief EMC <frequency, latency> information */
        struct emc_dvfs_latency pairs[EMC_DVFS_LATENCY_MAX_SIZE];
} __ABI_PACKED;

/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_CPU_NDIV_LIMITS
 * @brief CPU freq. limits in ndiv
 *
 * * Platforms: T194 onwards
 * @cond bpmp_t194
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_cpu_ndiv_limits_request
 * * Response Payload: @ref mrq_cpu_ndiv_limits_response
 * @addtogroup CPU
 * @{
 */

/**
 * @brief Request for ndiv limits of a cluster
 */
struct mrq_cpu_ndiv_limits_request {
        /** @brief Enum cluster_id */
        uint32_t cluster_id;
} __ABI_PACKED;

/**
 * @brief Response to #MRQ_CPU_NDIV_LIMITS
 */
struct mrq_cpu_ndiv_limits_response {
        /** @brief Reference frequency in Hz */
        uint32_t ref_clk_hz;
        /** @brief Post divider value */
        uint16_t pdiv;
        /** @brief Input divider value */
        uint16_t mdiv;
        /** @brief FMAX expressed with max NDIV value */
        uint16_t ndiv_max;
        /** @brief Minimum allowed NDIV value */
        uint16_t ndiv_min;
} __ABI_PACKED;

/** @} */
/** @endcond */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_CPU_AUTO_CC3
 * @brief Query CPU cluster auto-CC3 configuration
 *
 * * Platforms: T194 onwards
 * @cond bpmp_t194
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_cpu_auto_cc3_request
 * * Response Payload: @ref mrq_cpu_auto_cc3_response
 * @addtogroup CC3
 *
 * Queries from BPMP auto-CC3 configuration (allowed/not allowed) for a
 * specified cluster. CCPLEX s/w uses this information to override its own
 * device tree auto-CC3 settings, so that BPMP device tree is a single source of
 * auto-CC3 platform configuration.
 *
 * @{
 */

/**
 * @brief Request for auto-CC3 configuration of a cluster
 */
struct mrq_cpu_auto_cc3_request {
        /** @brief Enum cluster_id (logical cluster id, known to CCPLEX s/w) */
        uint32_t cluster_id;
} __ABI_PACKED;

/**
 * @brief Response to #MRQ_CPU_AUTO_CC3
 */
struct mrq_cpu_auto_cc3_response {
        /**
         * @brief auto-CC3 configuration
         *
         * - bits[31..10] reserved.
         * - bits[9..1] cc3 ndiv
         * - bit [0] if "1" auto-CC3 is allowed, if "0" auto-CC3 is not allowed
         */
        uint32_t auto_cc3_config;
} __ABI_PACKED;

/** @} */
/** @endcond */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_TRACE_ITER
 * @brief Manage the trace iterator
 *
 * * Platforms: All
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: N/A
 * * Response Payload: @ref mrq_trace_iter_request
 * @addtogroup Trace
 * @{
 */
enum {
        /** @brief (re)start the tracing now. Ignore older events */
        TRACE_ITER_INIT = 0,
        /** @brief Clobber all events in the trace buffer */
        TRACE_ITER_CLEAN = 1
};

/**
 * @brief Request with #MRQ_TRACE_ITER
 */
struct mrq_trace_iter_request {
        /** @brief TRACE_ITER_INIT or TRACE_ITER_CLEAN */
        uint32_t cmd;
} __ABI_PACKED;

/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_RINGBUF_CONSOLE
 * @brief A ring buffer debug console for BPMP
 * @addtogroup RingbufConsole
 *
 * The ring buffer debug console aims to be a substitute for the UART debug
 * console. The debug console is implemented with two ring buffers in the
 * BPMP-FW, the RX (receive) and TX (transmit) buffers. Characters can be read
 * and written to the buffers by the host via the MRQ interface.
 *
 * @{
 */

/**
 * @brief Maximum number of bytes transferred in a single write command to the
 * BPMP
 *
 * This is determined by the number of free bytes in the message struct,
 * rounded down to a multiple of four.
 */
#define MRQ_RINGBUF_CONSOLE_MAX_WRITE_LEN 112

/**
 * @brief Maximum number of bytes transferred in a single read command to the
 * BPMP
 *
 * This is determined by the number of free bytes in the message struct,
 * rounded down to a multiple of four.
 */
#define MRQ_RINGBUF_CONSOLE_MAX_READ_LEN 116

enum mrq_ringbuf_console_host_to_bpmp_cmd {
        /**
         * @brief Check whether the BPMP driver supports the specified request
         * type
         *
         * mrq_response::err is 0 if the specified request is supported and
         * -#BPMP_ENODEV otherwise
         */
        CMD_RINGBUF_CONSOLE_QUERY_ABI = 0,
        /**
         * @brief Perform a read operation on the BPMP TX buffer
         *
         * mrq_response::err is 0
         */
        CMD_RINGBUF_CONSOLE_READ = 1,
        /**
         * @brief Perform a write operation on the BPMP RX buffer
         *
         * mrq_response::err is 0 if the operation was successful and
         * -#BPMP_ENODEV otherwise
         */
        CMD_RINGBUF_CONSOLE_WRITE = 2,
        /**
         * @brief Get the length of the buffer and the physical addresses of
         * the buffer data and the head and tail counters
         *
         * mrq_response::err is 0 if the operation was successful and
         * -#BPMP_ENODEV otherwise
         */
        CMD_RINGBUF_CONSOLE_GET_FIFO = 3,
};

/**
 * @ingroup RingbufConsole
 * @brief Host->BPMP request data for request type
 * #CMD_RINGBUF_CONSOLE_QUERY_ABI
 */
struct cmd_ringbuf_console_query_abi_req {
        /** @brief Command identifier to be queried */
        uint32_t cmd;
} __ABI_PACKED;

/** @private */
struct cmd_ringbuf_console_query_abi_resp {
        EMPTY
} __ABI_PACKED;

/**
 * @ingroup RingbufConsole
 * @brief Host->BPMP request data for request type #CMD_RINGBUF_CONSOLE_READ
 */
struct cmd_ringbuf_console_read_req {
        /**
         * @brief Number of bytes requested to be read from the BPMP TX buffer
         */
        uint8_t len;
} __ABI_PACKED;

/**
 * @ingroup RingbufConsole
 * @brief BPMP->Host response data for request type #CMD_RINGBUF_CONSOLE_READ
 */
struct cmd_ringbuf_console_read_resp {
        /** @brief The actual data read from the BPMP TX buffer */
        uint8_t data[MRQ_RINGBUF_CONSOLE_MAX_READ_LEN];
        /** @brief Number of bytes in cmd_ringbuf_console_read_resp::data */
        uint8_t len;
} __ABI_PACKED;

/**
 * @ingroup RingbufConsole
 * @brief Host->BPMP request data for request type #CMD_RINGBUF_CONSOLE_WRITE
 */
struct cmd_ringbuf_console_write_req {
        /** @brief The actual data to be written to the BPMP RX buffer */
        uint8_t data[MRQ_RINGBUF_CONSOLE_MAX_WRITE_LEN];
        /** @brief Number of bytes in cmd_ringbuf_console_write_req::data */
        uint8_t len;
} __ABI_PACKED;

/**
 * @ingroup RingbufConsole
 * @brief BPMP->Host response data for request type #CMD_RINGBUF_CONSOLE_WRITE
 */
struct cmd_ringbuf_console_write_resp {
        /** @brief Number of bytes of available space in the BPMP RX buffer */
        uint32_t space_avail;
        /** @brief Number of bytes that were written to the BPMP RX buffer */
        uint8_t len;
} __ABI_PACKED;

/** @private */
struct cmd_ringbuf_console_get_fifo_req {
        EMPTY

} __ABI_PACKED;

/**
 * @ingroup RingbufConsole
 * @brief BPMP->Host reply data for request type #CMD_RINGBUF_CONSOLE_GET_FIFO
 */
struct cmd_ringbuf_console_get_fifo_resp {
        /** @brief Physical address of the BPMP TX buffer */
        uint64_t bpmp_tx_buf_addr;
        /** @brief Physical address of the BPMP TX buffer head counter */
        uint64_t bpmp_tx_head_addr;
        /** @brief Physical address of the BPMP TX buffer tail counter */
        uint64_t bpmp_tx_tail_addr;
        /** @brief Length of the BPMP TX buffer */
        uint32_t bpmp_tx_buf_len;
} __ABI_PACKED;

/**
 * @ingroup RingbufConsole
 * @brief Host->BPMP request data.
 *
 * Reply type is union #mrq_ringbuf_console_bpmp_to_host_response .
 */
struct mrq_ringbuf_console_host_to_bpmp_request {
        /**
         * @brief Type of request. Values listed in enum
         * #mrq_ringbuf_console_host_to_bpmp_cmd.
         */
        uint32_t type;
        /** @brief  request type specific parameters. */
        union {
                struct cmd_ringbuf_console_query_abi_req query_abi;
                struct cmd_ringbuf_console_read_req read;
                struct cmd_ringbuf_console_write_req write;
                struct cmd_ringbuf_console_get_fifo_req get_fifo;
        } __UNION_ANON;
} __ABI_PACKED;

/**
 * @ingroup RingbufConsole
 * @brief Host->BPMP reply data
 *
 * In response to struct #mrq_ringbuf_console_host_to_bpmp_request.
 */
union mrq_ringbuf_console_bpmp_to_host_response {
        struct cmd_ringbuf_console_query_abi_resp query_abi;
        struct cmd_ringbuf_console_read_resp read;
        struct cmd_ringbuf_console_write_resp write;
        struct cmd_ringbuf_console_get_fifo_resp get_fifo;
} __ABI_PACKED;
/** @} */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_STRAP
 * @brief Set a strap value controlled by BPMP
 *
 * * Platforms: T194 onwards
 * @cond bpmp_t194
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_strap_request
 * * Response Payload: N/A
 * @addtogroup Strap
 *
 * A strap is an input that is sampled by a hardware unit during the
 * unit's startup process. The sampled value of a strap affects the
 * behavior of the unit until the unit is restarted. Many hardware
 * units sample their straps at the instant that their resets are
 * deasserted.
 *
 * BPMP owns registers which act as straps to various units. It
 * exposes limited control of those straps via #MRQ_STRAP.
 *
 * @{
 */
enum mrq_strap_cmd {
        /** @private */
        STRAP_RESERVED = 0,
        /** @brief Set a strap value */
        STRAP_SET = 1
};

/**
 * @brief Request with #MRQ_STRAP
 */
struct mrq_strap_request {
        /** @brief @ref mrq_strap_cmd */
        uint32_t cmd;
        /** @brief Strap ID from @ref Strap_Ids */
        uint32_t id;
        /** @brief Desired value for strap (if cmd is #STRAP_SET) */
        uint32_t value;
} __ABI_PACKED;

/**
 * @defgroup Strap_Ids Strap Identifiers
 * @}
 */
/** @endcond */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_UPHY
 * @brief Perform a UPHY operation
 *
 * * Platforms: T194 onwards
 * @cond bpmp_t194
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_uphy_request
 * * Response Payload: @ref mrq_uphy_response
 *
 * @addtogroup UPHY
 * @{
 */
enum {
        CMD_UPHY_PCIE_LANE_MARGIN_CONTROL = 1,
        CMD_UPHY_PCIE_LANE_MARGIN_STATUS = 2,
        CMD_UPHY_PCIE_EP_CONTROLLER_PLL_INIT = 3,
        CMD_UPHY_PCIE_CONTROLLER_STATE = 4,
        CMD_UPHY_MAX,
};

struct cmd_uphy_margin_control_request {
        /** @brief Enable margin */
        int32_t en;
        /** @brief Clear the number of error and sections */
        int32_t clr;
        /** @brief Set x offset (1's complement) for left/right margin type (y should be 0) */
        uint32_t x;
        /** @brief Set y offset (1's complement) for left/right margin type (x should be 0) */
        uint32_t y;
        /** @brief Set number of bit blocks for each margin section */
        uint32_t nblks;
} __ABI_PACKED;

struct cmd_uphy_margin_status_response {
        /** @brief Number of errors observed */
        uint32_t status;
} __ABI_PACKED;

struct cmd_uphy_ep_controller_pll_init_request {
        /** @brief EP controller number, valid: 0, 4, 5 */
        uint8_t ep_controller;
} __ABI_PACKED;

struct cmd_uphy_pcie_controller_state_request {
        /** @brief PCIE controller number, valid: 0, 1, 2, 3, 4 */
        uint8_t pcie_controller;
        uint8_t enable;
} __ABI_PACKED;

/**
 * @ingroup UPHY
 * @brief Request with #MRQ_UPHY
 *
 * Used by the sender of an #MRQ_UPHY message to control UPHY Lane RX margining.
 * The uphy_request is split into several sub-commands. Some sub-commands
 * require no additional data. Others have a sub-command specific payload
 *
 * |sub-command                          |payload                                 |
 * |------------------------------------ |----------------------------------------|
 * |CMD_UPHY_PCIE_LANE_MARGIN_CONTROL    |uphy_set_margin_control                 |
 * |CMD_UPHY_PCIE_LANE_MARGIN_STATUS     |                                        |
 * |CMD_UPHY_PCIE_EP_CONTROLLER_PLL_INIT |cmd_uphy_ep_controller_pll_init_request |
 * |CMD_UPHY_PCIE_CONTROLLER_STATE       |cmd_uphy_pcie_controller_state_request  |
 *
 */

struct mrq_uphy_request {
        /** @brief Lane number. */
        uint16_t lane;
        /** @brief Sub-command id. */
        uint16_t cmd;

        union {
                struct cmd_uphy_margin_control_request uphy_set_margin_control;
                struct cmd_uphy_ep_controller_pll_init_request ep_ctrlr_pll_init;
                struct cmd_uphy_pcie_controller_state_request controller_state;
        } __UNION_ANON;
} __ABI_PACKED;

/**
 * @ingroup UPHY
 * @brief Response to MRQ_UPHY
 *
 * Each sub-command supported by @ref mrq_uphy_request may return
 * sub-command-specific data. Some do and some do not as indicated in
 * the following table
 *
 * |sub-command                       |payload                 |
 * |----------------------------      |------------------------|
 * |CMD_UPHY_PCIE_LANE_MARGIN_CONTROL |                        |
 * |CMD_UPHY_PCIE_LANE_MARGIN_STATUS  |uphy_get_margin_status  |
 *
 */

struct mrq_uphy_response {
        union {
                struct cmd_uphy_margin_status_response uphy_get_margin_status;
        } __UNION_ANON;
} __ABI_PACKED;

/** @} */
/** @endcond */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_FMON
 * @brief Perform a frequency monitor configuration operations
 *
 * * Platforms: T194 onwards
 * @cond bpmp_t194
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_fmon_request
 * * Response Payload: @ref mrq_fmon_response
 *
 * @addtogroup FMON
 * @{
 */
enum {
        /**
         * @brief Clamp FMON configuration to specified rate.
         *
         * The monitored clock must be running for clamp to succeed. If
         * clamped, FMON configuration is preserved when clock rate
         * and/or state is changed.
         */
        CMD_FMON_GEAR_CLAMP = 1,
        /**
         * @brief Release clamped FMON configuration.
         *
         * Allow FMON configuration to follow monitored clock rate
         * and/or state changes.
         */
        CMD_FMON_GEAR_FREE = 2,
        /**
         * @brief Return rate FMON is clamped at, or 0 if FMON is not
         *         clamped.
         *
         * Inherently racy, since clamp state can be changed
         * concurrently. Useful for testing.
         */
        CMD_FMON_GEAR_GET = 3,
        CMD_FMON_NUM,
};

struct cmd_fmon_gear_clamp_request {
        int32_t unused;
        int64_t rate;
} __ABI_PACKED;

/** @private */
struct cmd_fmon_gear_clamp_response {
        EMPTY
} __ABI_PACKED;

/** @private */
struct cmd_fmon_gear_free_request {
        EMPTY
} __ABI_PACKED;

/** @private */
struct cmd_fmon_gear_free_response {
        EMPTY
} __ABI_PACKED;

/** @private */
struct cmd_fmon_gear_get_request {
        EMPTY
} __ABI_PACKED;

struct cmd_fmon_gear_get_response {
        int64_t rate;
} __ABI_PACKED;

/**
 * @ingroup FMON
 * @brief Request with #MRQ_FMON
 *
 * Used by the sender of an #MRQ_FMON message to configure clock
 * frequency monitors. The FMON request is split into several
 * sub-commands. Some sub-commands require no additional data.
 * Others have a sub-command specific payload
 *
 * |sub-command                 |payload                |
 * |----------------------------|-----------------------|
 * |CMD_FMON_GEAR_CLAMP         |fmon_gear_clamp        |
 * |CMD_FMON_GEAR_FREE          |-                      |
 * |CMD_FMON_GEAR_GET           |-                      |
 *
 */

struct mrq_fmon_request {
        /** @brief Sub-command and clock id concatenated to 32-bit word.
         * - bits[31..24] is the sub-cmd.
         * - bits[23..0] is monitored clock id used to select target
         *   FMON
         */
        uint32_t cmd_and_id;

        union {
                struct cmd_fmon_gear_clamp_request fmon_gear_clamp;
                /** @private */
                struct cmd_fmon_gear_free_request fmon_gear_free;
                /** @private */
                struct cmd_fmon_gear_get_request fmon_gear_get;
        } __UNION_ANON;
} __ABI_PACKED;

/**
 * @ingroup FMON
 * @brief Response to MRQ_FMON
 *
 * Each sub-command supported by @ref mrq_fmon_request may
 * return sub-command-specific data as indicated below.
 *
 * |sub-command                 |payload                 |
 * |----------------------------|------------------------|
 * |CMD_FMON_GEAR_CLAMP         |-                       |
 * |CMD_FMON_GEAR_FREE          |-                       |
 * |CMD_FMON_GEAR_GET           |fmon_gear_get           |
 *
 */

struct mrq_fmon_response {
        union {
                /** @private */
                struct cmd_fmon_gear_clamp_response fmon_gear_clamp;
                /** @private */
                struct cmd_fmon_gear_free_response fmon_gear_free;
                struct cmd_fmon_gear_get_response fmon_gear_get;
        } __UNION_ANON;
} __ABI_PACKED;

/** @} */
/** @endcond */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_EC
 * @brief Provide status information on faults reported by Error
 *        Collator (EC) to HSM.
 *
 * * Platforms: T194 onwards
 * @cond bpmp_t194
 * * Initiators: CCPLEX
 * * Targets: BPMP
 * * Request Payload: @ref mrq_ec_request
 * * Response Payload: @ref mrq_ec_response
 *
 * @note This MRQ ABI is under construction, and subject to change
 *
 * @addtogroup EC
 * @{
 */
enum {
        /**
         * @brief Retrieve specified EC status.
         *
         * mrq_response::err is 0 if the operation was successful, or @n
         * -#BPMP_ENODEV if target EC is not owned by BPMP @n
         * -#BPMP_EACCES if target EC power domain is turned off
         */
        CMD_EC_STATUS_GET = 1,
        CMD_EC_NUM,
};

/** @brief BPMP ECs error types */
enum bpmp_ec_err_type {
        /** @brief Parity error on internal data path
         *
         *  Error descriptor @ref ec_err_simple_desc.
         */
        EC_ERR_TYPE_PARITY_INTERNAL             = 1,

        /** @brief ECC SEC error on internal data path
         *
         *  Error descriptor @ref ec_err_simple_desc.
         */
        EC_ERR_TYPE_ECC_SEC_INTERNAL            = 2,

        /** @brief ECC DED error on internal data path
         *
         *  Error descriptor @ref ec_err_simple_desc.
         */
        EC_ERR_TYPE_ECC_DED_INTERNAL            = 3,

        /** @brief Comparator error
         *
         *  Error descriptor @ref ec_err_simple_desc.
         */
        EC_ERR_TYPE_COMPARATOR                  = 4,

        /** @brief Register parity error
         *
         *  Error descriptor @ref ec_err_reg_parity_desc.
         */
        EC_ERR_TYPE_REGISTER_PARITY             = 5,

        /** @brief Parity error from on-chip SRAM/FIFO
         *
         *  Error descriptor @ref ec_err_simple_desc.
         */
        EC_ERR_TYPE_PARITY_SRAM                 = 6,

        /** @brief Clock Monitor error
         *
         *  Error descriptor @ref ec_err_fmon_desc.
         */
        EC_ERR_TYPE_CLOCK_MONITOR               = 9,

        /** @brief Voltage Monitor error
         *
         *  Error descriptor @ref ec_err_vmon_desc.
         */
        EC_ERR_TYPE_VOLTAGE_MONITOR             = 10,

        /** @brief SW Correctable error
         *
         *  Error descriptor @ref ec_err_simple_desc.
         */
        EC_ERR_TYPE_SW_CORRECTABLE              = 16,

        /** @brief SW Uncorrectable error
         *
         *  Error descriptor @ref ec_err_simple_desc.
         */
        EC_ERR_TYPE_SW_UNCORRECTABLE            = 17,

        /** @brief Other HW Correctable error
         *
         *  Error descriptor @ref ec_err_simple_desc.
         */
        EC_ERR_TYPE_OTHER_HW_CORRECTABLE        = 32,

        /** @brief Other HW Uncorrectable error
         *
         *  Error descriptor @ref ec_err_simple_desc.
         */
        EC_ERR_TYPE_OTHER_HW_UNCORRECTABLE      = 33,
};

/** @brief Group of registers with parity error. */
enum ec_registers_group {
        /** @brief Functional registers group */
        EC_ERR_GROUP_FUNC_REG           = 0,
        /** @brief SCR registers group */
        EC_ERR_GROUP_SCR_REG            = 1,
};

/**
 * @defgroup bpmp_ec_status_flags EC Status Flags
 * @addtogroup bpmp_ec_status_flags
 * @{
 */
/** @brief No EC error found flag */
#define EC_STATUS_FLAG_NO_ERROR         0x0001
/** @brief Last EC error found flag */
#define EC_STATUS_FLAG_LAST_ERROR       0x0002
/** @brief EC latent error flag */
#define EC_STATUS_FLAG_LATENT_ERROR     0x0004
/** @} */

/**
 * @defgroup bpmp_ec_desc_flags EC Descriptor Flags
 * @addtogroup bpmp_ec_desc_flags
 * @{
 */
/** @brief EC descriptor error resolved flag */
#define EC_DESC_FLAG_RESOLVED           0x0001
/** @brief EC descriptor failed to retrieve id flag */
#define EC_DESC_FLAG_NO_ID              0x0002
/** @} */

/**
 * |error type                       | fmon_clk_id values        |
 * |---------------------------------|---------------------------|
 * |@ref EC_ERR_TYPE_CLOCK_MONITOR   |@ref bpmp_clock_ids        |
 */
struct ec_err_fmon_desc {
        /** @brief Bitmask of @ref bpmp_ec_desc_flags  */
        uint16_t desc_flags;
        /** @brief FMON monitored clock id */
        uint16_t fmon_clk_id;
        /** @brief Bitmask of @ref bpmp_fmon_faults_flags */
        uint32_t fmon_faults;
        /** @brief FMON faults access error */
        int32_t fmon_access_error;
} __ABI_PACKED;

/**
 * |error type                       | vmon_adc_id values        |
 * |---------------------------------|---------------------------|
 * |@ref EC_ERR_TYPE_VOLTAGE_MONITOR |@ref bpmp_adc_ids          |
 */
struct ec_err_vmon_desc {
        /** @brief Bitmask of @ref bpmp_ec_desc_flags  */
        uint16_t desc_flags;
        /** @brief VMON rail adc id */
        uint16_t vmon_adc_id;
        /** @brief Bitmask of @ref bpmp_vmon_faults_flags */
        uint32_t vmon_faults;
        /** @brief VMON faults access error */
        int32_t vmon_access_error;
} __ABI_PACKED;

/**
 * |error type                       | reg_id values             |
 * |---------------------------------|---------------------------|
 * |@ref EC_ERR_TYPE_REGISTER_PARITY |@ref bpmp_ec_registers_ids |
 */
struct ec_err_reg_parity_desc {
        /** @brief Bitmask of @ref bpmp_ec_desc_flags  */
        uint16_t desc_flags;
        /** @brief Register id */
        uint16_t reg_id;
        /** @brief Register group @ref ec_registers_group */
        uint16_t reg_group;
} __ABI_PACKED;

/**
 * |error type                              | err_source_id values      |
 * |----------------------------------------|---------------------------|
 * |@ref EC_ERR_TYPE_PARITY_INTERNAL        |@ref bpmp_ec_ipath_ids     |
 * |@ref EC_ERR_TYPE_ECC_SEC_INTERNAL       |@ref bpmp_ec_ipath_ids     |
 * |@ref EC_ERR_TYPE_ECC_DED_INTERNAL       |@ref bpmp_ec_ipath_ids     |
 * |@ref EC_ERR_TYPE_COMPARATOR             |@ref bpmp_ec_comparator_ids|
 * |@ref EC_ERR_TYPE_PARITY_SRAM            |@ref bpmp_clock_ids        |
 * |@ref EC_ERR_TYPE_SW_CORRECTABLE         |@ref bpmp_ec_misc_ids      |
 * |@ref EC_ERR_TYPE_SW_UNCORRECTABLE       |@ref bpmp_ec_misc_ids      |
 * |@ref EC_ERR_TYPE_OTHER_HW_CORRECTABLE   |@ref bpmp_ec_misc_ids      |
 * |@ref EC_ERR_TYPE_OTHER_HW_UNCORRECTABLE |@ref bpmp_ec_misc_ids      |
 */
struct ec_err_simple_desc {
        /** @brief Bitmask of @ref bpmp_ec_desc_flags  */
        uint16_t desc_flags;
        /** @brief Error source id. Id space depends on error type. */
        uint16_t err_source_id;
} __ABI_PACKED;

/** @brief Union of EC error descriptors */
union ec_err_desc {
        struct ec_err_fmon_desc fmon_desc;
        struct ec_err_vmon_desc vmon_desc;
        struct ec_err_reg_parity_desc reg_parity_desc;
        struct ec_err_simple_desc simple_desc;
} __ABI_PACKED;

struct cmd_ec_status_get_request {
        /** @brief HSM error line number that identifies target EC. */
        uint32_t ec_hsm_id;
} __ABI_PACKED;

/** EC status maximum number of descriptors */
#define EC_ERR_STATUS_DESC_MAX_NUM      4

struct cmd_ec_status_get_response {
        /** @brief Target EC id (the same id received with request). */
        uint32_t ec_hsm_id;
        /**
         * @brief Bitmask of @ref bpmp_ec_status_flags
         *
         * If NO_ERROR flag is set, error_ fields should be ignored
         */
        uint32_t ec_status_flags;
        /** @brief Found EC error index. */
        uint32_t error_idx;
        /** @brief  Found EC error type @ref bpmp_ec_err_type. */
        uint32_t error_type;
        /** @brief  Number of returned EC error descriptors */
        uint32_t error_desc_num;
        /** @brief  EC error descriptors */
        union ec_err_desc error_descs[EC_ERR_STATUS_DESC_MAX_NUM];
} __ABI_PACKED;

/**
 * @ingroup EC
 * @brief Request with #MRQ_EC
 *
 * Used by the sender of an #MRQ_EC message to access ECs owned
 * by BPMP.
 *
 * |sub-command                 |payload                |
 * |----------------------------|-----------------------|
 * |@ref CMD_EC_STATUS_GET      |ec_status_get          |
 *
 */

struct mrq_ec_request {
        /** @brief Sub-command id. */
        uint32_t cmd_id;

        union {
                struct cmd_ec_status_get_request ec_status_get;
        } __UNION_ANON;
} __ABI_PACKED;

/**
 * @ingroup EC
 * @brief Response to MRQ_EC
 *
 * Each sub-command supported by @ref mrq_ec_request may return
 * sub-command-specific data as indicated below.
 *
 * |sub-command                 |payload                 |
 * |----------------------------|------------------------|
 * |@ref CMD_EC_STATUS_GET      |ec_status_get           |
 *
 */

struct mrq_ec_response {
        union {
                struct cmd_ec_status_get_response ec_status_get;
        } __UNION_ANON;
} __ABI_PACKED;

/** @} */
/** @endcond */

/**
 * @ingroup MRQ_Codes
 * @def MRQ_FBVOLT_STATUS
 * @brief Provides status information about voltage state for fuse burning
 *
 * * Platforms: T194 onwards
 * @cond bpmp_t194
 * * Initiators: CCPLEX
 * * Target: BPMP
 * * Request Payload: None
 * * Response Payload: @ref mrq_fbvolt_status_response
 * @{
 */

/**
 * @ingroup Fbvolt_status
 * @brief Response to #MRQ_FBVOLT_STATUS
 *
 * Value of #ready reflects if core voltages are in a suitable state for buring
 * fuses. A value of 0x1 indicates that core voltages are ready for burning
 * fuses. A value of 0x0 indicates that core voltages are not ready.
 */
struct mrq_fbvolt_status_response {
        /** @brief Bit [0:0] - ready status, bits [31:1] - reserved */
        uint32_t ready;
        /** @brief Reserved */
        uint32_t unused;
} __ABI_PACKED;

/** @} */
/** @endcond */

/**
 * @addtogroup Error_Codes
 * Negative values for mrq_response::err generally indicate some
 * error. The ABI defines the following error codes. Negating these
 * defines is an exercise left to the user.
 * @{
 */

/** @brief No such file or directory */
#define BPMP_ENOENT     2
/** @brief No MRQ handler */
#define BPMP_ENOHANDLER 3
/** @brief I/O error */
#define BPMP_EIO        5
/** @brief Bad sub-MRQ command */
#define BPMP_EBADCMD    6
/** @brief Not enough memory */
#define BPMP_ENOMEM     12
/** @brief Permission denied */
#define BPMP_EACCES     13
/** @brief Bad address */
#define BPMP_EFAULT     14
/** @brief No such device */
#define BPMP_ENODEV     19
/** @brief Argument is a directory */
#define BPMP_EISDIR     21
/** @brief Invalid argument */
#define BPMP_EINVAL     22
/** @brief Timeout during operation */
#define BPMP_ETIMEDOUT  23
/** @brief Out of range */
#define BPMP_ERANGE     34
/** @brief Function not implemented */
#define  BPMP_ENOSYS    38
/** @brief Invalid slot */
#define BPMP_EBADSLT    57

/** @} */

#endif