// SPDX-License-Identifier: GPL-2.0-only
/*
 * Copyright (C) 2015 VanguardiaSur - www.vanguardiasur.com.ar
 *
 * Based on original driver by Krzysztof Ha?asa:
 * Copyright (C) 2015 Industrial Research Institute for Automation
 * and Measurements PIAP
 *
 * Notes
 * -----
 *
 * 1. Under stress-testing, it has been observed that the PCIe link
 * goes down, without reason. Therefore, the driver takes special care
 * to allow device hot-unplugging.
 *
 * 2. TW686X devices are capable of setting a few different DMA modes,
 * including: scatter-gather, field and frame modes. However,
 * under stress testings it has been found that the machine can
 * freeze completely if DMA registers are programmed while streaming
 * is active.
 *
 * Therefore, driver implements a dma_mode called 'memcpy' which
 * avoids cycling the DMA buffers, and insteads allocates extra DMA buffers
 * and then copies into vmalloc'ed user buffers.
 *
 * In addition to this, when streaming is on, the driver tries to access
 * hardware registers as infrequently as possible. This is done by using
 * a timer to limit the rate at which DMA is reset on DMA channels error.
 */

#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci_ids.h>
#include <linux/slab.h>
#include <linux/timer.h>

#include "tw686x.h"
#include "tw686x-regs.h"

/*
 * This module parameter allows to control the DMA_TIMER_INTERVAL value.
 * The DMA_TIMER_INTERVAL register controls the minimum DMA interrupt
 * time span (iow, the maximum DMA interrupt rate) thus allowing for
 * IRQ coalescing.
 *
 * The chip datasheet does not mention a time unit for this value, so
 * users wanting fine-grain control over the interrupt rate should
 * determine the desired value through testing.
 */
static u32 dma_interval = 0x00098968;
module_param(dma_interval, int, 0444);
MODULE_PARM_DESC(dma_interval, "Minimum time span for DMA interrupting host");

static unsigned int dma_mode = TW686X_DMA_MODE_MEMCPY;
static const char *dma_mode_name(unsigned int mode)
{
        switch (mode) {
        case TW686X_DMA_MODE_MEMCPY:
                return "memcpy";
        case TW686X_DMA_MODE_CONTIG:
                return "contig";
        case TW686X_DMA_MODE_SG:
                return "sg";
        default:
                return "unknown";
        }
}

static int tw686x_dma_mode_get(char *buffer, const struct kernel_param *kp)
{
        return sprintf(buffer, "%s", dma_mode_name(dma_mode));
}

static int tw686x_dma_mode_set(const char *val, const struct kernel_param *kp)
{
        if (!strcasecmp(val, dma_mode_name(TW686X_DMA_MODE_MEMCPY)))
                dma_mode = TW686X_DMA_MODE_MEMCPY;
        else if (!strcasecmp(val, dma_mode_name(TW686X_DMA_MODE_CONTIG)))
                dma_mode = TW686X_DMA_MODE_CONTIG;
        else if (!strcasecmp(val, dma_mode_name(TW686X_DMA_MODE_SG)))
                dma_mode = TW686X_DMA_MODE_SG;
        else
                return -EINVAL;
        return 0;
}
module_param_call(dma_mode, tw686x_dma_mode_set, tw686x_dma_mode_get,
                  &dma_mode, S_IRUGO|S_IWUSR);
MODULE_PARM_DESC(dma_mode, "DMA operation mode (memcpy/contig/sg, default=memcpy)");

void tw686x_disable_channel(struct tw686x_dev *dev, unsigned int channel)
{
        u32 dma_en = reg_read(dev, DMA_CHANNEL_ENABLE);
        u32 dma_cmd = reg_read(dev, DMA_CMD);

        dma_en &= ~BIT(channel);
        dma_cmd &= ~BIT(channel);

        /* Must remove it from pending too */
        dev->pending_dma_en &= ~BIT(channel);
        dev->pending_dma_cmd &= ~BIT(channel);

        /* Stop DMA if no channels are enabled */
        if (!dma_en)
                dma_cmd = 0;
        reg_write(dev, DMA_CHANNEL_ENABLE, dma_en);
        reg_write(dev, DMA_CMD, dma_cmd);
}

void tw686x_enable_channel(struct tw686x_dev *dev, unsigned int channel)
{
        u32 dma_en = reg_read(dev, DMA_CHANNEL_ENABLE);
        u32 dma_cmd = reg_read(dev, DMA_CMD);

        dev->pending_dma_en |= dma_en | BIT(channel);
        dev->pending_dma_cmd |= dma_cmd | DMA_CMD_ENABLE | BIT(channel);
}

/*
 * The purpose of this awful hack is to avoid enabling the DMA
 * channels "too fast" which makes some TW686x devices very
 * angry and freeze the CPU (see note 1).
 */
static void tw686x_dma_delay(struct timer_list *t)
{
        struct tw686x_dev *dev = from_timer(dev, t, dma_delay_timer);
        unsigned long flags;

        spin_lock_irqsave(&dev->lock, flags);

        reg_write(dev, DMA_CHANNEL_ENABLE, dev->pending_dma_en);
        reg_write(dev, DMA_CMD, dev->pending_dma_cmd);
        dev->pending_dma_en = 0;
        dev->pending_dma_cmd = 0;

        spin_unlock_irqrestore(&dev->lock, flags);
}

static void tw686x_reset_channels(struct tw686x_dev *dev, unsigned int ch_mask)
{
        u32 dma_en, dma_cmd;

        dma_en = reg_read(dev, DMA_CHANNEL_ENABLE);
        dma_cmd = reg_read(dev, DMA_CMD);

        /*
         * Save pending register status, the timer will
         * restore them.
         */
        dev->pending_dma_en |= dma_en;
        dev->pending_dma_cmd |= dma_cmd;

        /* Disable the reset channels */
        reg_write(dev, DMA_CHANNEL_ENABLE, dma_en & ~ch_mask);

        if ((dma_en & ~ch_mask) == 0) {
                dev_dbg(&dev->pci_dev->dev, "reset: stopping DMA\n");
                dma_cmd &= ~DMA_CMD_ENABLE;
        }
        reg_write(dev, DMA_CMD, dma_cmd & ~ch_mask);
}

static irqreturn_t tw686x_irq(int irq, void *dev_id)
{
        struct tw686x_dev *dev = (struct tw686x_dev *)dev_id;
        unsigned int video_requests, audio_requests, reset_ch;
        u32 fifo_status, fifo_signal, fifo_ov, fifo_bad, fifo_errors;
        u32 int_status, dma_en, video_en, pb_status;
        unsigned long flags;

        int_status = reg_read(dev, INT_STATUS); /* cleared on read */
        fifo_status = reg_read(dev, VIDEO_FIFO_STATUS);

        /* INT_STATUS does not include FIFO_STATUS errors! */
        if (!int_status && !TW686X_FIFO_ERROR(fifo_status))
                return IRQ_NONE;

        if (int_status & INT_STATUS_DMA_TOUT) {
                dev_dbg(&dev->pci_dev->dev,
                        "DMA timeout. Resetting DMA for all channels\n");
                reset_ch = ~0;
                goto reset_channels;
        }

        spin_lock_irqsave(&dev->lock, flags);
        dma_en = reg_read(dev, DMA_CHANNEL_ENABLE);
        spin_unlock_irqrestore(&dev->lock, flags);

        video_en = dma_en & 0xff;
        fifo_signal = ~(fifo_status & 0xff) & video_en;
        fifo_ov = fifo_status >> 24;
        fifo_bad = fifo_status >> 16;

        /* Mask of channels with signal and FIFO errors */
        fifo_errors = fifo_signal & (fifo_ov | fifo_bad);

        reset_ch = 0;
        pb_status = reg_read(dev, PB_STATUS);

        /* Coalesce video frame/error events */
        video_requests = (int_status & video_en) | fifo_errors;
        audio_requests = (int_status & dma_en) >> 8;

        if (video_requests)
                tw686x_video_irq(dev, video_requests, pb_status,
                                 fifo_status, &reset_ch);
        if (audio_requests)
                tw686x_audio_irq(dev, audio_requests, pb_status);

reset_channels:
        if (reset_ch) {
                spin_lock_irqsave(&dev->lock, flags);
                tw686x_reset_channels(dev, reset_ch);
                spin_unlock_irqrestore(&dev->lock, flags);
                mod_timer(&dev->dma_delay_timer,
                          jiffies + msecs_to_jiffies(100));
        }

        return IRQ_HANDLED;
}

static void tw686x_dev_release(struct v4l2_device *v4l2_dev)
{
        struct tw686x_dev *dev = container_of(v4l2_dev, struct tw686x_dev,
                                              v4l2_dev);
        unsigned int ch;

        for (ch = 0; ch < max_channels(dev); ch++)
                v4l2_ctrl_handler_free(&dev->video_channels[ch].ctrl_handler);

        v4l2_device_unregister(&dev->v4l2_dev);

        kfree(dev->audio_channels);
        kfree(dev->video_channels);
        kfree(dev);
}

static int tw686x_probe(struct pci_dev *pci_dev,
                        const struct pci_device_id *pci_id)
{
        struct tw686x_dev *dev;
        int err;

        dev = kzalloc(sizeof(*dev), GFP_KERNEL);
        if (!dev)
                return -ENOMEM;
        dev->type = pci_id->driver_data;
        dev->dma_mode = dma_mode;
        sprintf(dev->name, "tw%04X", pci_dev->device);

        dev->video_channels = kcalloc(max_channels(dev),
                sizeof(*dev->video_channels), GFP_KERNEL);
        if (!dev->video_channels) {
                err = -ENOMEM;
                goto free_dev;
        }

        dev->audio_channels = kcalloc(max_channels(dev),
                sizeof(*dev->audio_channels), GFP_KERNEL);
        if (!dev->audio_channels) {
                err = -ENOMEM;
                goto free_video;
        }

        pr_info("%s: PCI %s, IRQ %d, MMIO 0x%lx (%s mode)\n", dev->name,
                pci_name(pci_dev), pci_dev->irq,
                (unsigned long)pci_resource_start(pci_dev, 0),
                dma_mode_name(dma_mode));

        dev->pci_dev = pci_dev;
        if (pci_enable_device(pci_dev)) {
                err = -EIO;
                goto free_audio;
        }

        pci_set_master(pci_dev);
        err = pci_set_dma_mask(pci_dev, DMA_BIT_MASK(32));
        if (err) {
                dev_err(&pci_dev->dev, "32-bit PCI DMA not supported\n");
                err = -EIO;
                goto disable_pci;
        }

        err = pci_request_regions(pci_dev, dev->name);
        if (err) {
                dev_err(&pci_dev->dev, "unable to request PCI region\n");
                goto disable_pci;
        }

        dev->mmio = pci_ioremap_bar(pci_dev, 0);
        if (!dev->mmio) {
                dev_err(&pci_dev->dev, "unable to remap PCI region\n");
                err = -ENOMEM;
                goto free_region;
        }

        /* Reset all subsystems */
        reg_write(dev, SYS_SOFT_RST, 0x0f);
        mdelay(1);

        reg_write(dev, SRST[0], 0x3f);
        if (max_channels(dev) > 4)
                reg_write(dev, SRST[1], 0x3f);

        /* Disable the DMA engine */
        reg_write(dev, DMA_CMD, 0);
        reg_write(dev, DMA_CHANNEL_ENABLE, 0);

        /* Enable DMA FIFO overflow and pointer check */
        reg_write(dev, DMA_CONFIG, 0xffffff04);
        reg_write(dev, DMA_CHANNEL_TIMEOUT, 0x140c8584);
        reg_write(dev, DMA_TIMER_INTERVAL, dma_interval);

        spin_lock_init(&dev->lock);

        err = request_irq(pci_dev->irq, tw686x_irq, IRQF_SHARED,
                          dev->name, dev);
        if (err < 0) {
                dev_err(&pci_dev->dev, "unable to request interrupt\n");
                goto iounmap;
        }

        timer_setup(&dev->dma_delay_timer, tw686x_dma_delay, 0);

        /*
         * This must be set right before initializing v4l2_dev.
         * It's used to release resources after the last handle
         * held is released.
         */
        dev->v4l2_dev.release = tw686x_dev_release;
        err = tw686x_video_init(dev);
        if (err) {
                dev_err(&pci_dev->dev, "can't register video\n");
                goto free_irq;
        }

        err = tw686x_audio_init(dev);
        if (err)
                dev_warn(&pci_dev->dev, "can't register audio\n");

        pci_set_drvdata(pci_dev, dev);
        return 0;

free_irq:
        free_irq(pci_dev->irq, dev);
iounmap:
        pci_iounmap(pci_dev, dev->mmio);
free_region:
        pci_release_regions(pci_dev);
disable_pci:
        pci_disable_device(pci_dev);
free_audio:
        kfree(dev->audio_channels);
free_video:
        kfree(dev->video_channels);
free_dev:
        kfree(dev);
        return err;
}

static void tw686x_remove(struct pci_dev *pci_dev)
{
        struct tw686x_dev *dev = pci_get_drvdata(pci_dev);
        unsigned long flags;

        /* This guarantees the IRQ handler is no longer running,
         * which means we can kiss good-bye some resources.
         */
        free_irq(pci_dev->irq, dev);

        tw686x_video_free(dev);
        tw686x_audio_free(dev);
        del_timer_sync(&dev->dma_delay_timer);

        pci_iounmap(pci_dev, dev->mmio);
        pci_release_regions(pci_dev);
        pci_disable_device(pci_dev);

        /*
         * Setting pci_dev to NULL allows to detect hardware is no longer
         * available and will be used by vb2_ops. This is required because
         * the device sometimes hot-unplugs itself as the result of a PCIe
         * link down.
         * The lock is really important here.
         */
        spin_lock_irqsave(&dev->lock, flags);
        dev->pci_dev = NULL;
        spin_unlock_irqrestore(&dev->lock, flags);

        /*
         * This calls tw686x_dev_release if it's the last reference.
         * Otherwise, release is postponed until there are no users left.
         */
        v4l2_device_put(&dev->v4l2_dev);
}

/*
 * On TW6864 and TW6868, all channels share the pair of video DMA SG tables,
 * with 10-bit start_idx and end_idx determining start and end of frame buffer
 * for particular channel.
 * TW6868 with all its 8 channels would be problematic (only 127 SG entries per
 * channel) but we support only 4 channels on this chip anyway (the first
 * 4 channels are driven with internal video decoder, the other 4 would require
 * an external TW286x part).
 *
 * On TW6865 and TW6869, each channel has its own DMA SG table, with indexes
 * starting with 0. Both chips have complete sets of internal video decoders
 * (respectively 4 or 8-channel).
 *
 * All chips have separate SG tables for two video frames.
 */

/* driver_data is number of A/V channels */
static const struct pci_device_id tw686x_pci_tbl[] = {
        {
                PCI_DEVICE(PCI_VENDOR_ID_TECHWELL, 0x6864),
                .driver_data = 4
        },
        {
                PCI_DEVICE(PCI_VENDOR_ID_TECHWELL, 0x6865), /* not tested */
                .driver_data = 4 | TYPE_SECOND_GEN
        },
        /*
         * TW6868 supports 8 A/V channels with an external TW2865 chip;
         * not supported by the driver.
         */
        {
                PCI_DEVICE(PCI_VENDOR_ID_TECHWELL, 0x6868), /* not tested */
                .driver_data = 4
        },
        {
                PCI_DEVICE(PCI_VENDOR_ID_TECHWELL, 0x6869),
                .driver_data = 8 | TYPE_SECOND_GEN},
        {}
};
MODULE_DEVICE_TABLE(pci, tw686x_pci_tbl);

static struct pci_driver tw686x_pci_driver = {
        .name = "tw686x",
        .id_table = tw686x_pci_tbl,
        .probe = tw686x_probe,
        .remove = tw686x_remove,
};
module_pci_driver(tw686x_pci_driver);

MODULE_DESCRIPTION("Driver for video frame grabber cards based on Intersil/Techwell TW686[4589]");
MODULE_AUTHOR("Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>");
MODULE_AUTHOR("Krzysztof Ha?asa <khalasa@piap.pl>");
MODULE_LICENSE("GPL v2");