linux/drivers/net/dsa/microchip/ksz8795.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0
   2/*
   3 * Microchip KSZ8795 switch driver
   4 *
   5 * Copyright (C) 2017 Microchip Technology Inc.
   6 *      Tristram Ha <Tristram.Ha@microchip.com>
   7 */
   8
   9#include <linux/delay.h>
  10#include <linux/export.h>
  11#include <linux/gpio.h>
  12#include <linux/kernel.h>
  13#include <linux/module.h>
  14#include <linux/platform_data/microchip-ksz.h>
  15#include <linux/phy.h>
  16#include <linux/etherdevice.h>
  17#include <linux/if_bridge.h>
  18#include <net/dsa.h>
  19#include <net/switchdev.h>
  20
  21#include "ksz_common.h"
  22#include "ksz8795_reg.h"
  23
  24static const struct {
  25        char string[ETH_GSTRING_LEN];
  26} mib_names[TOTAL_SWITCH_COUNTER_NUM] = {
  27        { "rx_hi" },
  28        { "rx_undersize" },
  29        { "rx_fragments" },
  30        { "rx_oversize" },
  31        { "rx_jabbers" },
  32        { "rx_symbol_err" },
  33        { "rx_crc_err" },
  34        { "rx_align_err" },
  35        { "rx_mac_ctrl" },
  36        { "rx_pause" },
  37        { "rx_bcast" },
  38        { "rx_mcast" },
  39        { "rx_ucast" },
  40        { "rx_64_or_less" },
  41        { "rx_65_127" },
  42        { "rx_128_255" },
  43        { "rx_256_511" },
  44        { "rx_512_1023" },
  45        { "rx_1024_1522" },
  46        { "rx_1523_2000" },
  47        { "rx_2001" },
  48        { "tx_hi" },
  49        { "tx_late_col" },
  50        { "tx_pause" },
  51        { "tx_bcast" },
  52        { "tx_mcast" },
  53        { "tx_ucast" },
  54        { "tx_deferred" },
  55        { "tx_total_col" },
  56        { "tx_exc_col" },
  57        { "tx_single_col" },
  58        { "tx_mult_col" },
  59        { "rx_total" },
  60        { "tx_total" },
  61        { "rx_discards" },
  62        { "tx_discards" },
  63};
  64
  65static void ksz_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set)
  66{
  67        regmap_update_bits(dev->regmap[0], addr, bits, set ? bits : 0);
  68}
  69
  70static void ksz_port_cfg(struct ksz_device *dev, int port, int offset, u8 bits,
  71                         bool set)
  72{
  73        regmap_update_bits(dev->regmap[0], PORT_CTRL_ADDR(port, offset),
  74                           bits, set ? bits : 0);
  75}
  76
  77static int ksz8795_reset_switch(struct ksz_device *dev)
  78{
  79        /* reset switch */
  80        ksz_write8(dev, REG_POWER_MANAGEMENT_1,
  81                   SW_SOFTWARE_POWER_DOWN << SW_POWER_MANAGEMENT_MODE_S);
  82        ksz_write8(dev, REG_POWER_MANAGEMENT_1, 0);
  83
  84        return 0;
  85}
  86
  87static void ksz8795_set_prio_queue(struct ksz_device *dev, int port, int queue)
  88{
  89        u8 hi, lo;
  90
  91        /* Number of queues can only be 1, 2, or 4. */
  92        switch (queue) {
  93        case 4:
  94        case 3:
  95                queue = PORT_QUEUE_SPLIT_4;
  96                break;
  97        case 2:
  98                queue = PORT_QUEUE_SPLIT_2;
  99                break;
 100        default:
 101                queue = PORT_QUEUE_SPLIT_1;
 102        }
 103        ksz_pread8(dev, port, REG_PORT_CTRL_0, &lo);
 104        ksz_pread8(dev, port, P_DROP_TAG_CTRL, &hi);
 105        lo &= ~PORT_QUEUE_SPLIT_L;
 106        if (queue & PORT_QUEUE_SPLIT_2)
 107                lo |= PORT_QUEUE_SPLIT_L;
 108        hi &= ~PORT_QUEUE_SPLIT_H;
 109        if (queue & PORT_QUEUE_SPLIT_4)
 110                hi |= PORT_QUEUE_SPLIT_H;
 111        ksz_pwrite8(dev, port, REG_PORT_CTRL_0, lo);
 112        ksz_pwrite8(dev, port, P_DROP_TAG_CTRL, hi);
 113
 114        /* Default is port based for egress rate limit. */
 115        if (queue != PORT_QUEUE_SPLIT_1)
 116                ksz_cfg(dev, REG_SW_CTRL_19, SW_OUT_RATE_LIMIT_QUEUE_BASED,
 117                        true);
 118}
 119
 120static void ksz8795_r_mib_cnt(struct ksz_device *dev, int port, u16 addr,
 121                              u64 *cnt)
 122{
 123        u16 ctrl_addr;
 124        u32 data;
 125        u8 check;
 126        int loop;
 127
 128        ctrl_addr = addr + SWITCH_COUNTER_NUM * port;
 129        ctrl_addr |= IND_ACC_TABLE(TABLE_MIB | TABLE_READ);
 130
 131        mutex_lock(&dev->alu_mutex);
 132        ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
 133
 134        /* It is almost guaranteed to always read the valid bit because of
 135         * slow SPI speed.
 136         */
 137        for (loop = 2; loop > 0; loop--) {
 138                ksz_read8(dev, REG_IND_MIB_CHECK, &check);
 139
 140                if (check & MIB_COUNTER_VALID) {
 141                        ksz_read32(dev, REG_IND_DATA_LO, &data);
 142                        if (check & MIB_COUNTER_OVERFLOW)
 143                                *cnt += MIB_COUNTER_VALUE + 1;
 144                        *cnt += data & MIB_COUNTER_VALUE;
 145                        break;
 146                }
 147        }
 148        mutex_unlock(&dev->alu_mutex);
 149}
 150
 151static void ksz8795_r_mib_pkt(struct ksz_device *dev, int port, u16 addr,
 152                              u64 *dropped, u64 *cnt)
 153{
 154        u16 ctrl_addr;
 155        u32 data;
 156        u8 check;
 157        int loop;
 158
 159        addr -= SWITCH_COUNTER_NUM;
 160        ctrl_addr = (KS_MIB_TOTAL_RX_1 - KS_MIB_TOTAL_RX_0) * port;
 161        ctrl_addr += addr + KS_MIB_TOTAL_RX_0;
 162        ctrl_addr |= IND_ACC_TABLE(TABLE_MIB | TABLE_READ);
 163
 164        mutex_lock(&dev->alu_mutex);
 165        ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
 166
 167        /* It is almost guaranteed to always read the valid bit because of
 168         * slow SPI speed.
 169         */
 170        for (loop = 2; loop > 0; loop--) {
 171                ksz_read8(dev, REG_IND_MIB_CHECK, &check);
 172
 173                if (check & MIB_COUNTER_VALID) {
 174                        ksz_read32(dev, REG_IND_DATA_LO, &data);
 175                        if (addr < 2) {
 176                                u64 total;
 177
 178                                total = check & MIB_TOTAL_BYTES_H;
 179                                total <<= 32;
 180                                *cnt += total;
 181                                *cnt += data;
 182                                if (check & MIB_COUNTER_OVERFLOW) {
 183                                        total = MIB_TOTAL_BYTES_H + 1;
 184                                        total <<= 32;
 185                                        *cnt += total;
 186                                }
 187                        } else {
 188                                if (check & MIB_COUNTER_OVERFLOW)
 189                                        *cnt += MIB_PACKET_DROPPED + 1;
 190                                *cnt += data & MIB_PACKET_DROPPED;
 191                        }
 192                        break;
 193                }
 194        }
 195        mutex_unlock(&dev->alu_mutex);
 196}
 197
 198static void ksz8795_freeze_mib(struct ksz_device *dev, int port, bool freeze)
 199{
 200        /* enable the port for flush/freeze function */
 201        if (freeze)
 202                ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), true);
 203        ksz_cfg(dev, REG_SW_CTRL_6, SW_MIB_COUNTER_FREEZE, freeze);
 204
 205        /* disable the port after freeze is done */
 206        if (!freeze)
 207                ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), false);
 208}
 209
 210static void ksz8795_port_init_cnt(struct ksz_device *dev, int port)
 211{
 212        struct ksz_port_mib *mib = &dev->ports[port].mib;
 213
 214        /* flush all enabled port MIB counters */
 215        ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), true);
 216        ksz_cfg(dev, REG_SW_CTRL_6, SW_MIB_COUNTER_FLUSH, true);
 217        ksz_cfg(dev, REG_SW_CTRL_6, BIT(port), false);
 218
 219        mib->cnt_ptr = 0;
 220
 221        /* Some ports may not have MIB counters before SWITCH_COUNTER_NUM. */
 222        while (mib->cnt_ptr < dev->reg_mib_cnt) {
 223                dev->dev_ops->r_mib_cnt(dev, port, mib->cnt_ptr,
 224                                        &mib->counters[mib->cnt_ptr]);
 225                ++mib->cnt_ptr;
 226        }
 227
 228        /* Some ports may not have MIB counters after SWITCH_COUNTER_NUM. */
 229        while (mib->cnt_ptr < dev->mib_cnt) {
 230                dev->dev_ops->r_mib_pkt(dev, port, mib->cnt_ptr,
 231                                        NULL, &mib->counters[mib->cnt_ptr]);
 232                ++mib->cnt_ptr;
 233        }
 234        mib->cnt_ptr = 0;
 235        memset(mib->counters, 0, dev->mib_cnt * sizeof(u64));
 236}
 237
 238static void ksz8795_r_table(struct ksz_device *dev, int table, u16 addr,
 239                            u64 *data)
 240{
 241        u16 ctrl_addr;
 242
 243        ctrl_addr = IND_ACC_TABLE(table | TABLE_READ) | addr;
 244
 245        mutex_lock(&dev->alu_mutex);
 246        ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
 247        ksz_read64(dev, REG_IND_DATA_HI, data);
 248        mutex_unlock(&dev->alu_mutex);
 249}
 250
 251static void ksz8795_w_table(struct ksz_device *dev, int table, u16 addr,
 252                            u64 data)
 253{
 254        u16 ctrl_addr;
 255
 256        ctrl_addr = IND_ACC_TABLE(table) | addr;
 257
 258        mutex_lock(&dev->alu_mutex);
 259        ksz_write64(dev, REG_IND_DATA_HI, data);
 260        ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
 261        mutex_unlock(&dev->alu_mutex);
 262}
 263
 264static int ksz8795_valid_dyn_entry(struct ksz_device *dev, u8 *data)
 265{
 266        int timeout = 100;
 267
 268        do {
 269                ksz_read8(dev, REG_IND_DATA_CHECK, data);
 270                timeout--;
 271        } while ((*data & DYNAMIC_MAC_TABLE_NOT_READY) && timeout);
 272
 273        /* Entry is not ready for accessing. */
 274        if (*data & DYNAMIC_MAC_TABLE_NOT_READY) {
 275                return -EAGAIN;
 276        /* Entry is ready for accessing. */
 277        } else {
 278                ksz_read8(dev, REG_IND_DATA_8, data);
 279
 280                /* There is no valid entry in the table. */
 281                if (*data & DYNAMIC_MAC_TABLE_MAC_EMPTY)
 282                        return -ENXIO;
 283        }
 284        return 0;
 285}
 286
 287static int ksz8795_r_dyn_mac_table(struct ksz_device *dev, u16 addr,
 288                                   u8 *mac_addr, u8 *fid, u8 *src_port,
 289                                   u8 *timestamp, u16 *entries)
 290{
 291        u32 data_hi, data_lo;
 292        u16 ctrl_addr;
 293        u8 data;
 294        int rc;
 295
 296        ctrl_addr = IND_ACC_TABLE(TABLE_DYNAMIC_MAC | TABLE_READ) | addr;
 297
 298        mutex_lock(&dev->alu_mutex);
 299        ksz_write16(dev, REG_IND_CTRL_0, ctrl_addr);
 300
 301        rc = ksz8795_valid_dyn_entry(dev, &data);
 302        if (rc == -EAGAIN) {
 303                if (addr == 0)
 304                        *entries = 0;
 305        } else if (rc == -ENXIO) {
 306                *entries = 0;
 307        /* At least one valid entry in the table. */
 308        } else {
 309                u64 buf = 0;
 310                int cnt;
 311
 312                ksz_read64(dev, REG_IND_DATA_HI, &buf);
 313                data_hi = (u32)(buf >> 32);
 314                data_lo = (u32)buf;
 315
 316                /* Check out how many valid entry in the table. */
 317                cnt = data & DYNAMIC_MAC_TABLE_ENTRIES_H;
 318                cnt <<= DYNAMIC_MAC_ENTRIES_H_S;
 319                cnt |= (data_hi & DYNAMIC_MAC_TABLE_ENTRIES) >>
 320                        DYNAMIC_MAC_ENTRIES_S;
 321                *entries = cnt + 1;
 322
 323                *fid = (data_hi & DYNAMIC_MAC_TABLE_FID) >>
 324                        DYNAMIC_MAC_FID_S;
 325                *src_port = (data_hi & DYNAMIC_MAC_TABLE_SRC_PORT) >>
 326                        DYNAMIC_MAC_SRC_PORT_S;
 327                *timestamp = (data_hi & DYNAMIC_MAC_TABLE_TIMESTAMP) >>
 328                        DYNAMIC_MAC_TIMESTAMP_S;
 329
 330                mac_addr[5] = (u8)data_lo;
 331                mac_addr[4] = (u8)(data_lo >> 8);
 332                mac_addr[3] = (u8)(data_lo >> 16);
 333                mac_addr[2] = (u8)(data_lo >> 24);
 334
 335                mac_addr[1] = (u8)data_hi;
 336                mac_addr[0] = (u8)(data_hi >> 8);
 337                rc = 0;
 338        }
 339        mutex_unlock(&dev->alu_mutex);
 340
 341        return rc;
 342}
 343
 344static int ksz8795_r_sta_mac_table(struct ksz_device *dev, u16 addr,
 345                                   struct alu_struct *alu)
 346{
 347        u32 data_hi, data_lo;
 348        u64 data;
 349
 350        ksz8795_r_table(dev, TABLE_STATIC_MAC, addr, &data);
 351        data_hi = data >> 32;
 352        data_lo = (u32)data;
 353        if (data_hi & (STATIC_MAC_TABLE_VALID | STATIC_MAC_TABLE_OVERRIDE)) {
 354                alu->mac[5] = (u8)data_lo;
 355                alu->mac[4] = (u8)(data_lo >> 8);
 356                alu->mac[3] = (u8)(data_lo >> 16);
 357                alu->mac[2] = (u8)(data_lo >> 24);
 358                alu->mac[1] = (u8)data_hi;
 359                alu->mac[0] = (u8)(data_hi >> 8);
 360                alu->port_forward = (data_hi & STATIC_MAC_TABLE_FWD_PORTS) >>
 361                        STATIC_MAC_FWD_PORTS_S;
 362                alu->is_override =
 363                        (data_hi & STATIC_MAC_TABLE_OVERRIDE) ? 1 : 0;
 364                data_hi >>= 1;
 365                alu->is_use_fid = (data_hi & STATIC_MAC_TABLE_USE_FID) ? 1 : 0;
 366                alu->fid = (data_hi & STATIC_MAC_TABLE_FID) >>
 367                        STATIC_MAC_FID_S;
 368                return 0;
 369        }
 370        return -ENXIO;
 371}
 372
 373static void ksz8795_w_sta_mac_table(struct ksz_device *dev, u16 addr,
 374                                    struct alu_struct *alu)
 375{
 376        u32 data_hi, data_lo;
 377        u64 data;
 378
 379        data_lo = ((u32)alu->mac[2] << 24) |
 380                ((u32)alu->mac[3] << 16) |
 381                ((u32)alu->mac[4] << 8) | alu->mac[5];
 382        data_hi = ((u32)alu->mac[0] << 8) | alu->mac[1];
 383        data_hi |= (u32)alu->port_forward << STATIC_MAC_FWD_PORTS_S;
 384
 385        if (alu->is_override)
 386                data_hi |= STATIC_MAC_TABLE_OVERRIDE;
 387        if (alu->is_use_fid) {
 388                data_hi |= STATIC_MAC_TABLE_USE_FID;
 389                data_hi |= (u32)alu->fid << STATIC_MAC_FID_S;
 390        }
 391        if (alu->is_static)
 392                data_hi |= STATIC_MAC_TABLE_VALID;
 393        else
 394                data_hi &= ~STATIC_MAC_TABLE_OVERRIDE;
 395
 396        data = (u64)data_hi << 32 | data_lo;
 397        ksz8795_w_table(dev, TABLE_STATIC_MAC, addr, data);
 398}
 399
 400static void ksz8795_from_vlan(u16 vlan, u8 *fid, u8 *member, u8 *valid)
 401{
 402        *fid = vlan & VLAN_TABLE_FID;
 403        *member = (vlan & VLAN_TABLE_MEMBERSHIP) >> VLAN_TABLE_MEMBERSHIP_S;
 404        *valid = !!(vlan & VLAN_TABLE_VALID);
 405}
 406
 407static void ksz8795_to_vlan(u8 fid, u8 member, u8 valid, u16 *vlan)
 408{
 409        *vlan = fid;
 410        *vlan |= (u16)member << VLAN_TABLE_MEMBERSHIP_S;
 411        if (valid)
 412                *vlan |= VLAN_TABLE_VALID;
 413}
 414
 415static void ksz8795_r_vlan_entries(struct ksz_device *dev, u16 addr)
 416{
 417        u64 data;
 418        int i;
 419
 420        ksz8795_r_table(dev, TABLE_VLAN, addr, &data);
 421        addr *= 4;
 422        for (i = 0; i < 4; i++) {
 423                dev->vlan_cache[addr + i].table[0] = (u16)data;
 424                data >>= VLAN_TABLE_S;
 425        }
 426}
 427
 428static void ksz8795_r_vlan_table(struct ksz_device *dev, u16 vid, u16 *vlan)
 429{
 430        int index;
 431        u16 *data;
 432        u16 addr;
 433        u64 buf;
 434
 435        data = (u16 *)&buf;
 436        addr = vid / 4;
 437        index = vid & 3;
 438        ksz8795_r_table(dev, TABLE_VLAN, addr, &buf);
 439        *vlan = data[index];
 440}
 441
 442static void ksz8795_w_vlan_table(struct ksz_device *dev, u16 vid, u16 vlan)
 443{
 444        int index;
 445        u16 *data;
 446        u16 addr;
 447        u64 buf;
 448
 449        data = (u16 *)&buf;
 450        addr = vid / 4;
 451        index = vid & 3;
 452        ksz8795_r_table(dev, TABLE_VLAN, addr, &buf);
 453        data[index] = vlan;
 454        dev->vlan_cache[vid].table[0] = vlan;
 455        ksz8795_w_table(dev, TABLE_VLAN, addr, buf);
 456}
 457
 458static void ksz8795_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
 459{
 460        u8 restart, speed, ctrl, link;
 461        int processed = true;
 462        u16 data = 0;
 463        u8 p = phy;
 464
 465        switch (reg) {
 466        case PHY_REG_CTRL:
 467                ksz_pread8(dev, p, P_NEG_RESTART_CTRL, &restart);
 468                ksz_pread8(dev, p, P_SPEED_STATUS, &speed);
 469                ksz_pread8(dev, p, P_FORCE_CTRL, &ctrl);
 470                if (restart & PORT_PHY_LOOPBACK)
 471                        data |= PHY_LOOPBACK;
 472                if (ctrl & PORT_FORCE_100_MBIT)
 473                        data |= PHY_SPEED_100MBIT;
 474                if (!(ctrl & PORT_AUTO_NEG_DISABLE))
 475                        data |= PHY_AUTO_NEG_ENABLE;
 476                if (restart & PORT_POWER_DOWN)
 477                        data |= PHY_POWER_DOWN;
 478                if (restart & PORT_AUTO_NEG_RESTART)
 479                        data |= PHY_AUTO_NEG_RESTART;
 480                if (ctrl & PORT_FORCE_FULL_DUPLEX)
 481                        data |= PHY_FULL_DUPLEX;
 482                if (speed & PORT_HP_MDIX)
 483                        data |= PHY_HP_MDIX;
 484                if (restart & PORT_FORCE_MDIX)
 485                        data |= PHY_FORCE_MDIX;
 486                if (restart & PORT_AUTO_MDIX_DISABLE)
 487                        data |= PHY_AUTO_MDIX_DISABLE;
 488                if (restart & PORT_TX_DISABLE)
 489                        data |= PHY_TRANSMIT_DISABLE;
 490                if (restart & PORT_LED_OFF)
 491                        data |= PHY_LED_DISABLE;
 492                break;
 493        case PHY_REG_STATUS:
 494                ksz_pread8(dev, p, P_LINK_STATUS, &link);
 495                data = PHY_100BTX_FD_CAPABLE |
 496                       PHY_100BTX_CAPABLE |
 497                       PHY_10BT_FD_CAPABLE |
 498                       PHY_10BT_CAPABLE |
 499                       PHY_AUTO_NEG_CAPABLE;
 500                if (link & PORT_AUTO_NEG_COMPLETE)
 501                        data |= PHY_AUTO_NEG_ACKNOWLEDGE;
 502                if (link & PORT_STAT_LINK_GOOD)
 503                        data |= PHY_LINK_STATUS;
 504                break;
 505        case PHY_REG_ID_1:
 506                data = KSZ8795_ID_HI;
 507                break;
 508        case PHY_REG_ID_2:
 509                data = KSZ8795_ID_LO;
 510                break;
 511        case PHY_REG_AUTO_NEGOTIATION:
 512                ksz_pread8(dev, p, P_LOCAL_CTRL, &ctrl);
 513                data = PHY_AUTO_NEG_802_3;
 514                if (ctrl & PORT_AUTO_NEG_SYM_PAUSE)
 515                        data |= PHY_AUTO_NEG_SYM_PAUSE;
 516                if (ctrl & PORT_AUTO_NEG_100BTX_FD)
 517                        data |= PHY_AUTO_NEG_100BTX_FD;
 518                if (ctrl & PORT_AUTO_NEG_100BTX)
 519                        data |= PHY_AUTO_NEG_100BTX;
 520                if (ctrl & PORT_AUTO_NEG_10BT_FD)
 521                        data |= PHY_AUTO_NEG_10BT_FD;
 522                if (ctrl & PORT_AUTO_NEG_10BT)
 523                        data |= PHY_AUTO_NEG_10BT;
 524                break;
 525        case PHY_REG_REMOTE_CAPABILITY:
 526                ksz_pread8(dev, p, P_REMOTE_STATUS, &link);
 527                data = PHY_AUTO_NEG_802_3;
 528                if (link & PORT_REMOTE_SYM_PAUSE)
 529                        data |= PHY_AUTO_NEG_SYM_PAUSE;
 530                if (link & PORT_REMOTE_100BTX_FD)
 531                        data |= PHY_AUTO_NEG_100BTX_FD;
 532                if (link & PORT_REMOTE_100BTX)
 533                        data |= PHY_AUTO_NEG_100BTX;
 534                if (link & PORT_REMOTE_10BT_FD)
 535                        data |= PHY_AUTO_NEG_10BT_FD;
 536                if (link & PORT_REMOTE_10BT)
 537                        data |= PHY_AUTO_NEG_10BT;
 538                if (data & ~PHY_AUTO_NEG_802_3)
 539                        data |= PHY_REMOTE_ACKNOWLEDGE_NOT;
 540                break;
 541        default:
 542                processed = false;
 543                break;
 544        }
 545        if (processed)
 546                *val = data;
 547}
 548
 549static void ksz8795_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
 550{
 551        u8 p = phy;
 552        u8 restart, speed, ctrl, data;
 553
 554        switch (reg) {
 555        case PHY_REG_CTRL:
 556
 557                /* Do not support PHY reset function. */
 558                if (val & PHY_RESET)
 559                        break;
 560                ksz_pread8(dev, p, P_SPEED_STATUS, &speed);
 561                data = speed;
 562                if (val & PHY_HP_MDIX)
 563                        data |= PORT_HP_MDIX;
 564                else
 565                        data &= ~PORT_HP_MDIX;
 566                if (data != speed)
 567                        ksz_pwrite8(dev, p, P_SPEED_STATUS, data);
 568                ksz_pread8(dev, p, P_FORCE_CTRL, &ctrl);
 569                data = ctrl;
 570                if (!(val & PHY_AUTO_NEG_ENABLE))
 571                        data |= PORT_AUTO_NEG_DISABLE;
 572                else
 573                        data &= ~PORT_AUTO_NEG_DISABLE;
 574
 575                /* Fiber port does not support auto-negotiation. */
 576                if (dev->ports[p].fiber)
 577                        data |= PORT_AUTO_NEG_DISABLE;
 578                if (val & PHY_SPEED_100MBIT)
 579                        data |= PORT_FORCE_100_MBIT;
 580                else
 581                        data &= ~PORT_FORCE_100_MBIT;
 582                if (val & PHY_FULL_DUPLEX)
 583                        data |= PORT_FORCE_FULL_DUPLEX;
 584                else
 585                        data &= ~PORT_FORCE_FULL_DUPLEX;
 586                if (data != ctrl)
 587                        ksz_pwrite8(dev, p, P_FORCE_CTRL, data);
 588                ksz_pread8(dev, p, P_NEG_RESTART_CTRL, &restart);
 589                data = restart;
 590                if (val & PHY_LED_DISABLE)
 591                        data |= PORT_LED_OFF;
 592                else
 593                        data &= ~PORT_LED_OFF;
 594                if (val & PHY_TRANSMIT_DISABLE)
 595                        data |= PORT_TX_DISABLE;
 596                else
 597                        data &= ~PORT_TX_DISABLE;
 598                if (val & PHY_AUTO_NEG_RESTART)
 599                        data |= PORT_AUTO_NEG_RESTART;
 600                else
 601                        data &= ~(PORT_AUTO_NEG_RESTART);
 602                if (val & PHY_POWER_DOWN)
 603                        data |= PORT_POWER_DOWN;
 604                else
 605                        data &= ~PORT_POWER_DOWN;
 606                if (val & PHY_AUTO_MDIX_DISABLE)
 607                        data |= PORT_AUTO_MDIX_DISABLE;
 608                else
 609                        data &= ~PORT_AUTO_MDIX_DISABLE;
 610                if (val & PHY_FORCE_MDIX)
 611                        data |= PORT_FORCE_MDIX;
 612                else
 613                        data &= ~PORT_FORCE_MDIX;
 614                if (val & PHY_LOOPBACK)
 615                        data |= PORT_PHY_LOOPBACK;
 616                else
 617                        data &= ~PORT_PHY_LOOPBACK;
 618                if (data != restart)
 619                        ksz_pwrite8(dev, p, P_NEG_RESTART_CTRL, data);
 620                break;
 621        case PHY_REG_AUTO_NEGOTIATION:
 622                ksz_pread8(dev, p, P_LOCAL_CTRL, &ctrl);
 623                data = ctrl;
 624                data &= ~(PORT_AUTO_NEG_SYM_PAUSE |
 625                          PORT_AUTO_NEG_100BTX_FD |
 626                          PORT_AUTO_NEG_100BTX |
 627                          PORT_AUTO_NEG_10BT_FD |
 628                          PORT_AUTO_NEG_10BT);
 629                if (val & PHY_AUTO_NEG_SYM_PAUSE)
 630                        data |= PORT_AUTO_NEG_SYM_PAUSE;
 631                if (val & PHY_AUTO_NEG_100BTX_FD)
 632                        data |= PORT_AUTO_NEG_100BTX_FD;
 633                if (val & PHY_AUTO_NEG_100BTX)
 634                        data |= PORT_AUTO_NEG_100BTX;
 635                if (val & PHY_AUTO_NEG_10BT_FD)
 636                        data |= PORT_AUTO_NEG_10BT_FD;
 637                if (val & PHY_AUTO_NEG_10BT)
 638                        data |= PORT_AUTO_NEG_10BT;
 639                if (data != ctrl)
 640                        ksz_pwrite8(dev, p, P_LOCAL_CTRL, data);
 641                break;
 642        default:
 643                break;
 644        }
 645}
 646
 647static enum dsa_tag_protocol ksz8795_get_tag_protocol(struct dsa_switch *ds,
 648                                                      int port)
 649{
 650        return DSA_TAG_PROTO_KSZ8795;
 651}
 652
 653static void ksz8795_get_strings(struct dsa_switch *ds, int port,
 654                                u32 stringset, uint8_t *buf)
 655{
 656        int i;
 657
 658        for (i = 0; i < TOTAL_SWITCH_COUNTER_NUM; i++) {
 659                memcpy(buf + i * ETH_GSTRING_LEN, mib_names[i].string,
 660                       ETH_GSTRING_LEN);
 661        }
 662}
 663
 664static void ksz8795_cfg_port_member(struct ksz_device *dev, int port,
 665                                    u8 member)
 666{
 667        u8 data;
 668
 669        ksz_pread8(dev, port, P_MIRROR_CTRL, &data);
 670        data &= ~PORT_VLAN_MEMBERSHIP;
 671        data |= (member & dev->port_mask);
 672        ksz_pwrite8(dev, port, P_MIRROR_CTRL, data);
 673        dev->ports[port].member = member;
 674}
 675
 676static void ksz8795_port_stp_state_set(struct dsa_switch *ds, int port,
 677                                       u8 state)
 678{
 679        struct ksz_device *dev = ds->priv;
 680        int forward = dev->member;
 681        struct ksz_port *p;
 682        int member = -1;
 683        u8 data;
 684
 685        p = &dev->ports[port];
 686
 687        ksz_pread8(dev, port, P_STP_CTRL, &data);
 688        data &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE | PORT_LEARN_DISABLE);
 689
 690        switch (state) {
 691        case BR_STATE_DISABLED:
 692                data |= PORT_LEARN_DISABLE;
 693                if (port < SWITCH_PORT_NUM)
 694                        member = 0;
 695                break;
 696        case BR_STATE_LISTENING:
 697                data |= (PORT_RX_ENABLE | PORT_LEARN_DISABLE);
 698                if (port < SWITCH_PORT_NUM &&
 699                    p->stp_state == BR_STATE_DISABLED)
 700                        member = dev->host_mask | p->vid_member;
 701                break;
 702        case BR_STATE_LEARNING:
 703                data |= PORT_RX_ENABLE;
 704                break;
 705        case BR_STATE_FORWARDING:
 706                data |= (PORT_TX_ENABLE | PORT_RX_ENABLE);
 707
 708                /* This function is also used internally. */
 709                if (port == dev->cpu_port)
 710                        break;
 711
 712                /* Port is a member of a bridge. */
 713                if (dev->br_member & BIT(port)) {
 714                        dev->member |= BIT(port);
 715                        member = dev->member;
 716                } else {
 717                        member = dev->host_mask | p->vid_member;
 718                }
 719                break;
 720        case BR_STATE_BLOCKING:
 721                data |= PORT_LEARN_DISABLE;
 722                if (port < SWITCH_PORT_NUM &&
 723                    p->stp_state == BR_STATE_DISABLED)
 724                        member = dev->host_mask | p->vid_member;
 725                break;
 726        default:
 727                dev_err(ds->dev, "invalid STP state: %d\n", state);
 728                return;
 729        }
 730
 731        ksz_pwrite8(dev, port, P_STP_CTRL, data);
 732        p->stp_state = state;
 733        if (data & PORT_RX_ENABLE)
 734                dev->rx_ports |= BIT(port);
 735        else
 736                dev->rx_ports &= ~BIT(port);
 737        if (data & PORT_TX_ENABLE)
 738                dev->tx_ports |= BIT(port);
 739        else
 740                dev->tx_ports &= ~BIT(port);
 741
 742        /* Port membership may share register with STP state. */
 743        if (member >= 0 && member != p->member)
 744                ksz8795_cfg_port_member(dev, port, (u8)member);
 745
 746        /* Check if forwarding needs to be updated. */
 747        if (state != BR_STATE_FORWARDING) {
 748                if (dev->br_member & BIT(port))
 749                        dev->member &= ~BIT(port);
 750        }
 751
 752        /* When topology has changed the function ksz_update_port_member
 753         * should be called to modify port forwarding behavior.
 754         */
 755        if (forward != dev->member)
 756                ksz_update_port_member(dev, port);
 757}
 758
 759static void ksz8795_flush_dyn_mac_table(struct ksz_device *dev, int port)
 760{
 761        u8 learn[TOTAL_PORT_NUM];
 762        int first, index, cnt;
 763        struct ksz_port *p;
 764
 765        if ((uint)port < TOTAL_PORT_NUM) {
 766                first = port;
 767                cnt = port + 1;
 768        } else {
 769                /* Flush all ports. */
 770                first = 0;
 771                cnt = dev->mib_port_cnt;
 772        }
 773        for (index = first; index < cnt; index++) {
 774                p = &dev->ports[index];
 775                if (!p->on)
 776                        continue;
 777                ksz_pread8(dev, index, P_STP_CTRL, &learn[index]);
 778                if (!(learn[index] & PORT_LEARN_DISABLE))
 779                        ksz_pwrite8(dev, index, P_STP_CTRL,
 780                                    learn[index] | PORT_LEARN_DISABLE);
 781        }
 782        ksz_cfg(dev, S_FLUSH_TABLE_CTRL, SW_FLUSH_DYN_MAC_TABLE, true);
 783        for (index = first; index < cnt; index++) {
 784                p = &dev->ports[index];
 785                if (!p->on)
 786                        continue;
 787                if (!(learn[index] & PORT_LEARN_DISABLE))
 788                        ksz_pwrite8(dev, index, P_STP_CTRL, learn[index]);
 789        }
 790}
 791
 792static int ksz8795_port_vlan_filtering(struct dsa_switch *ds, int port,
 793                                       bool flag)
 794{
 795        struct ksz_device *dev = ds->priv;
 796
 797        ksz_cfg(dev, S_MIRROR_CTRL, SW_VLAN_ENABLE, flag);
 798
 799        return 0;
 800}
 801
 802static void ksz8795_port_vlan_add(struct dsa_switch *ds, int port,
 803                                  const struct switchdev_obj_port_vlan *vlan)
 804{
 805        bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
 806        struct ksz_device *dev = ds->priv;
 807        u16 data, vid, new_pvid = 0;
 808        u8 fid, member, valid;
 809
 810        ksz_port_cfg(dev, port, P_TAG_CTRL, PORT_REMOVE_TAG, untagged);
 811
 812        for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) {
 813                ksz8795_r_vlan_table(dev, vid, &data);
 814                ksz8795_from_vlan(data, &fid, &member, &valid);
 815
 816                /* First time to setup the VLAN entry. */
 817                if (!valid) {
 818                        /* Need to find a way to map VID to FID. */
 819                        fid = 1;
 820                        valid = 1;
 821                }
 822                member |= BIT(port);
 823
 824                ksz8795_to_vlan(fid, member, valid, &data);
 825                ksz8795_w_vlan_table(dev, vid, data);
 826
 827                /* change PVID */
 828                if (vlan->flags & BRIDGE_VLAN_INFO_PVID)
 829                        new_pvid = vid;
 830        }
 831
 832        if (new_pvid) {
 833                ksz_pread16(dev, port, REG_PORT_CTRL_VID, &vid);
 834                vid &= 0xfff;
 835                vid |= new_pvid;
 836                ksz_pwrite16(dev, port, REG_PORT_CTRL_VID, vid);
 837        }
 838}
 839
 840static int ksz8795_port_vlan_del(struct dsa_switch *ds, int port,
 841                                 const struct switchdev_obj_port_vlan *vlan)
 842{
 843        bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED;
 844        struct ksz_device *dev = ds->priv;
 845        u16 data, vid, pvid, new_pvid = 0;
 846        u8 fid, member, valid;
 847
 848        ksz_pread16(dev, port, REG_PORT_CTRL_VID, &pvid);
 849        pvid = pvid & 0xFFF;
 850
 851        ksz_port_cfg(dev, port, P_TAG_CTRL, PORT_REMOVE_TAG, untagged);
 852
 853        for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) {
 854                ksz8795_r_vlan_table(dev, vid, &data);
 855                ksz8795_from_vlan(data, &fid, &member, &valid);
 856
 857                member &= ~BIT(port);
 858
 859                /* Invalidate the entry if no more member. */
 860                if (!member) {
 861                        fid = 0;
 862                        valid = 0;
 863                }
 864
 865                if (pvid == vid)
 866                        new_pvid = 1;
 867
 868                ksz8795_to_vlan(fid, member, valid, &data);
 869                ksz8795_w_vlan_table(dev, vid, data);
 870        }
 871
 872        if (new_pvid != pvid)
 873                ksz_pwrite16(dev, port, REG_PORT_CTRL_VID, pvid);
 874
 875        return 0;
 876}
 877
 878static int ksz8795_port_mirror_add(struct dsa_switch *ds, int port,
 879                                   struct dsa_mall_mirror_tc_entry *mirror,
 880                                   bool ingress)
 881{
 882        struct ksz_device *dev = ds->priv;
 883
 884        if (ingress) {
 885                ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, true);
 886                dev->mirror_rx |= BIT(port);
 887        } else {
 888                ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, true);
 889                dev->mirror_tx |= BIT(port);
 890        }
 891
 892        ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_SNIFFER, false);
 893
 894        /* configure mirror port */
 895        if (dev->mirror_rx || dev->mirror_tx)
 896                ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL,
 897                             PORT_MIRROR_SNIFFER, true);
 898
 899        return 0;
 900}
 901
 902static void ksz8795_port_mirror_del(struct dsa_switch *ds, int port,
 903                                    struct dsa_mall_mirror_tc_entry *mirror)
 904{
 905        struct ksz_device *dev = ds->priv;
 906        u8 data;
 907
 908        if (mirror->ingress) {
 909                ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, false);
 910                dev->mirror_rx &= ~BIT(port);
 911        } else {
 912                ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, false);
 913                dev->mirror_tx &= ~BIT(port);
 914        }
 915
 916        ksz_pread8(dev, port, P_MIRROR_CTRL, &data);
 917
 918        if (!dev->mirror_rx && !dev->mirror_tx)
 919                ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL,
 920                             PORT_MIRROR_SNIFFER, false);
 921}
 922
 923static void ksz8795_port_setup(struct ksz_device *dev, int port, bool cpu_port)
 924{
 925        struct ksz_port *p = &dev->ports[port];
 926        u8 data8, member;
 927
 928        /* enable broadcast storm limit */
 929        ksz_port_cfg(dev, port, P_BCAST_STORM_CTRL, PORT_BROADCAST_STORM, true);
 930
 931        ksz8795_set_prio_queue(dev, port, 4);
 932
 933        /* disable DiffServ priority */
 934        ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_DIFFSERV_ENABLE, false);
 935
 936        /* replace priority */
 937        ksz_port_cfg(dev, port, P_802_1P_CTRL, PORT_802_1P_REMAPPING, false);
 938
 939        /* enable 802.1p priority */
 940        ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_ENABLE, true);
 941
 942        if (cpu_port) {
 943                /* Configure MII interface for proper network communication. */
 944                ksz_read8(dev, REG_PORT_5_CTRL_6, &data8);
 945                data8 &= ~PORT_INTERFACE_TYPE;
 946                data8 &= ~PORT_GMII_1GPS_MODE;
 947                switch (dev->interface) {
 948                case PHY_INTERFACE_MODE_MII:
 949                        p->phydev.speed = SPEED_100;
 950                        break;
 951                case PHY_INTERFACE_MODE_RMII:
 952                        data8 |= PORT_INTERFACE_RMII;
 953                        p->phydev.speed = SPEED_100;
 954                        break;
 955                case PHY_INTERFACE_MODE_GMII:
 956                        data8 |= PORT_GMII_1GPS_MODE;
 957                        data8 |= PORT_INTERFACE_GMII;
 958                        p->phydev.speed = SPEED_1000;
 959                        break;
 960                default:
 961                        data8 &= ~PORT_RGMII_ID_IN_ENABLE;
 962                        data8 &= ~PORT_RGMII_ID_OUT_ENABLE;
 963                        if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
 964                            dev->interface == PHY_INTERFACE_MODE_RGMII_RXID)
 965                                data8 |= PORT_RGMII_ID_IN_ENABLE;
 966                        if (dev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
 967                            dev->interface == PHY_INTERFACE_MODE_RGMII_TXID)
 968                                data8 |= PORT_RGMII_ID_OUT_ENABLE;
 969                        data8 |= PORT_GMII_1GPS_MODE;
 970                        data8 |= PORT_INTERFACE_RGMII;
 971                        p->phydev.speed = SPEED_1000;
 972                        break;
 973                }
 974                ksz_write8(dev, REG_PORT_5_CTRL_6, data8);
 975                p->phydev.duplex = 1;
 976
 977                member = dev->port_mask;
 978                dev->on_ports = dev->host_mask;
 979                dev->live_ports = dev->host_mask;
 980        } else {
 981                member = dev->host_mask | p->vid_member;
 982                dev->on_ports |= BIT(port);
 983
 984                /* Link was detected before port is enabled. */
 985                if (p->phydev.link)
 986                        dev->live_ports |= BIT(port);
 987        }
 988        ksz8795_cfg_port_member(dev, port, member);
 989}
 990
 991static void ksz8795_config_cpu_port(struct dsa_switch *ds)
 992{
 993        struct ksz_device *dev = ds->priv;
 994        struct ksz_port *p;
 995        u8 remote;
 996        int i;
 997
 998        ds->num_ports = dev->port_cnt + 1;
 999
1000        /* Switch marks the maximum frame with extra byte as oversize. */
1001        ksz_cfg(dev, REG_SW_CTRL_2, SW_LEGAL_PACKET_DISABLE, true);
1002        ksz_cfg(dev, S_TAIL_TAG_CTRL, SW_TAIL_TAG_ENABLE, true);
1003
1004        p = &dev->ports[dev->cpu_port];
1005        p->vid_member = dev->port_mask;
1006        p->on = 1;
1007
1008        ksz8795_port_setup(dev, dev->cpu_port, true);
1009        dev->member = dev->host_mask;
1010
1011        for (i = 0; i < SWITCH_PORT_NUM; i++) {
1012                p = &dev->ports[i];
1013
1014                /* Initialize to non-zero so that ksz_cfg_port_member() will
1015                 * be called.
1016                 */
1017                p->vid_member = BIT(i);
1018                p->member = dev->port_mask;
1019                ksz8795_port_stp_state_set(ds, i, BR_STATE_DISABLED);
1020
1021                /* Last port may be disabled. */
1022                if (i == dev->port_cnt)
1023                        break;
1024                p->on = 1;
1025                p->phy = 1;
1026        }
1027        for (i = 0; i < dev->phy_port_cnt; i++) {
1028                p = &dev->ports[i];
1029                if (!p->on)
1030                        continue;
1031                ksz_pread8(dev, i, P_REMOTE_STATUS, &remote);
1032                if (remote & PORT_FIBER_MODE)
1033                        p->fiber = 1;
1034                if (p->fiber)
1035                        ksz_port_cfg(dev, i, P_STP_CTRL, PORT_FORCE_FLOW_CTRL,
1036                                     true);
1037                else
1038                        ksz_port_cfg(dev, i, P_STP_CTRL, PORT_FORCE_FLOW_CTRL,
1039                                     false);
1040        }
1041}
1042
1043static int ksz8795_setup(struct dsa_switch *ds)
1044{
1045        struct ksz_device *dev = ds->priv;
1046        struct alu_struct alu;
1047        int i, ret = 0;
1048
1049        dev->vlan_cache = devm_kcalloc(dev->dev, sizeof(struct vlan_table),
1050                                       dev->num_vlans, GFP_KERNEL);
1051        if (!dev->vlan_cache)
1052                return -ENOMEM;
1053
1054        ret = ksz8795_reset_switch(dev);
1055        if (ret) {
1056                dev_err(ds->dev, "failed to reset switch\n");
1057                return ret;
1058        }
1059
1060        ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_FLOW_CTRL, true);
1061
1062        /* Enable automatic fast aging when link changed detected. */
1063        ksz_cfg(dev, S_LINK_AGING_CTRL, SW_LINK_AUTO_AGING, true);
1064
1065        /* Enable aggressive back off algorithm in half duplex mode. */
1066        regmap_update_bits(dev->regmap[0], REG_SW_CTRL_1,
1067                           SW_AGGR_BACKOFF, SW_AGGR_BACKOFF);
1068
1069        /*
1070         * Make sure unicast VLAN boundary is set as default and
1071         * enable no excessive collision drop.
1072         */
1073        regmap_update_bits(dev->regmap[0], REG_SW_CTRL_2,
1074                           UNICAST_VLAN_BOUNDARY | NO_EXC_COLLISION_DROP,
1075                           UNICAST_VLAN_BOUNDARY | NO_EXC_COLLISION_DROP);
1076
1077        ksz8795_config_cpu_port(ds);
1078
1079        ksz_cfg(dev, REG_SW_CTRL_2, MULTICAST_STORM_DISABLE, true);
1080
1081        ksz_cfg(dev, S_REPLACE_VID_CTRL, SW_REPLACE_VID, false);
1082
1083        ksz_cfg(dev, S_MIRROR_CTRL, SW_MIRROR_RX_TX, false);
1084
1085        /* set broadcast storm protection 10% rate */
1086        regmap_update_bits(dev->regmap[1], S_REPLACE_VID_CTRL,
1087                           BROADCAST_STORM_RATE,
1088                           (BROADCAST_STORM_VALUE *
1089                           BROADCAST_STORM_PROT_RATE) / 100);
1090
1091        for (i = 0; i < VLAN_TABLE_ENTRIES; i++)
1092                ksz8795_r_vlan_entries(dev, i);
1093
1094        /* Setup STP address for STP operation. */
1095        memset(&alu, 0, sizeof(alu));
1096        ether_addr_copy(alu.mac, eth_stp_addr);
1097        alu.is_static = true;
1098        alu.is_override = true;
1099        alu.port_forward = dev->host_mask;
1100
1101        ksz8795_w_sta_mac_table(dev, 0, &alu);
1102
1103        ksz_init_mib_timer(dev);
1104
1105        return 0;
1106}
1107
1108static const struct dsa_switch_ops ksz8795_switch_ops = {
1109        .get_tag_protocol       = ksz8795_get_tag_protocol,
1110        .setup                  = ksz8795_setup,
1111        .phy_read               = ksz_phy_read16,
1112        .phy_write              = ksz_phy_write16,
1113        .adjust_link            = ksz_adjust_link,
1114        .port_enable            = ksz_enable_port,
1115        .port_disable           = ksz_disable_port,
1116        .get_strings            = ksz8795_get_strings,
1117        .get_ethtool_stats      = ksz_get_ethtool_stats,
1118        .get_sset_count         = ksz_sset_count,
1119        .port_bridge_join       = ksz_port_bridge_join,
1120        .port_bridge_leave      = ksz_port_bridge_leave,
1121        .port_stp_state_set     = ksz8795_port_stp_state_set,
1122        .port_fast_age          = ksz_port_fast_age,
1123        .port_vlan_filtering    = ksz8795_port_vlan_filtering,
1124        .port_vlan_prepare      = ksz_port_vlan_prepare,
1125        .port_vlan_add          = ksz8795_port_vlan_add,
1126        .port_vlan_del          = ksz8795_port_vlan_del,
1127        .port_fdb_dump          = ksz_port_fdb_dump,
1128        .port_mdb_prepare       = ksz_port_mdb_prepare,
1129        .port_mdb_add           = ksz_port_mdb_add,
1130        .port_mdb_del           = ksz_port_mdb_del,
1131        .port_mirror_add        = ksz8795_port_mirror_add,
1132        .port_mirror_del        = ksz8795_port_mirror_del,
1133};
1134
1135static u32 ksz8795_get_port_addr(int port, int offset)
1136{
1137        return PORT_CTRL_ADDR(port, offset);
1138}
1139
1140static int ksz8795_switch_detect(struct ksz_device *dev)
1141{
1142        u8 id1, id2;
1143        u16 id16;
1144        int ret;
1145
1146        /* read chip id */
1147        ret = ksz_read16(dev, REG_CHIP_ID0, &id16);
1148        if (ret)
1149                return ret;
1150
1151        id1 = id16 >> 8;
1152        id2 = id16 & SW_CHIP_ID_M;
1153        if (id1 != FAMILY_ID ||
1154            (id2 != CHIP_ID_94 && id2 != CHIP_ID_95))
1155                return -ENODEV;
1156
1157        dev->mib_port_cnt = TOTAL_PORT_NUM;
1158        dev->phy_port_cnt = SWITCH_PORT_NUM;
1159        dev->port_cnt = SWITCH_PORT_NUM;
1160
1161        if (id2 == CHIP_ID_95) {
1162                u8 val;
1163
1164                id2 = 0x95;
1165                ksz_read8(dev, REG_PORT_1_STATUS_0, &val);
1166                if (val & PORT_FIBER_MODE)
1167                        id2 = 0x65;
1168        } else if (id2 == CHIP_ID_94) {
1169                dev->port_cnt--;
1170                dev->last_port = dev->port_cnt;
1171                id2 = 0x94;
1172        }
1173        id16 &= ~0xff;
1174        id16 |= id2;
1175        dev->chip_id = id16;
1176
1177        dev->cpu_port = dev->mib_port_cnt - 1;
1178        dev->host_mask = BIT(dev->cpu_port);
1179
1180        return 0;
1181}
1182
1183struct ksz_chip_data {
1184        u16 chip_id;
1185        const char *dev_name;
1186        int num_vlans;
1187        int num_alus;
1188        int num_statics;
1189        int cpu_ports;
1190        int port_cnt;
1191};
1192
1193static const struct ksz_chip_data ksz8795_switch_chips[] = {
1194        {
1195                .chip_id = 0x8795,
1196                .dev_name = "KSZ8795",
1197                .num_vlans = 4096,
1198                .num_alus = 0,
1199                .num_statics = 8,
1200                .cpu_ports = 0x10,      /* can be configured as cpu port */
1201                .port_cnt = 4,          /* total physical port count */
1202        },
1203        {
1204                .chip_id = 0x8794,
1205                .dev_name = "KSZ8794",
1206                .num_vlans = 4096,
1207                .num_alus = 0,
1208                .num_statics = 8,
1209                .cpu_ports = 0x10,      /* can be configured as cpu port */
1210                .port_cnt = 3,          /* total physical port count */
1211        },
1212        {
1213                .chip_id = 0x8765,
1214                .dev_name = "KSZ8765",
1215                .num_vlans = 4096,
1216                .num_alus = 0,
1217                .num_statics = 8,
1218                .cpu_ports = 0x10,      /* can be configured as cpu port */
1219                .port_cnt = 4,          /* total physical port count */
1220        },
1221};
1222
1223static int ksz8795_switch_init(struct ksz_device *dev)
1224{
1225        int i;
1226
1227        dev->ds->ops = &ksz8795_switch_ops;
1228
1229        for (i = 0; i < ARRAY_SIZE(ksz8795_switch_chips); i++) {
1230                const struct ksz_chip_data *chip = &ksz8795_switch_chips[i];
1231
1232                if (dev->chip_id == chip->chip_id) {
1233                        dev->name = chip->dev_name;
1234                        dev->num_vlans = chip->num_vlans;
1235                        dev->num_alus = chip->num_alus;
1236                        dev->num_statics = chip->num_statics;
1237                        dev->port_cnt = chip->port_cnt;
1238                        dev->cpu_ports = chip->cpu_ports;
1239
1240                        break;
1241                }
1242        }
1243
1244        /* no switch found */
1245        if (!dev->cpu_ports)
1246                return -ENODEV;
1247
1248        dev->port_mask = BIT(dev->port_cnt) - 1;
1249        dev->port_mask |= dev->host_mask;
1250
1251        dev->reg_mib_cnt = SWITCH_COUNTER_NUM;
1252        dev->mib_cnt = TOTAL_SWITCH_COUNTER_NUM;
1253
1254        i = dev->mib_port_cnt;
1255        dev->ports = devm_kzalloc(dev->dev, sizeof(struct ksz_port) * i,
1256                                  GFP_KERNEL);
1257        if (!dev->ports)
1258                return -ENOMEM;
1259        for (i = 0; i < dev->mib_port_cnt; i++) {
1260                mutex_init(&dev->ports[i].mib.cnt_mutex);
1261                dev->ports[i].mib.counters =
1262                        devm_kzalloc(dev->dev,
1263                                     sizeof(u64) *
1264                                     (TOTAL_SWITCH_COUNTER_NUM + 1),
1265                                     GFP_KERNEL);
1266                if (!dev->ports[i].mib.counters)
1267                        return -ENOMEM;
1268        }
1269
1270        return 0;
1271}
1272
1273static void ksz8795_switch_exit(struct ksz_device *dev)
1274{
1275        ksz8795_reset_switch(dev);
1276}
1277
1278static const struct ksz_dev_ops ksz8795_dev_ops = {
1279        .get_port_addr = ksz8795_get_port_addr,
1280        .cfg_port_member = ksz8795_cfg_port_member,
1281        .flush_dyn_mac_table = ksz8795_flush_dyn_mac_table,
1282        .port_setup = ksz8795_port_setup,
1283        .r_phy = ksz8795_r_phy,
1284        .w_phy = ksz8795_w_phy,
1285        .r_dyn_mac_table = ksz8795_r_dyn_mac_table,
1286        .r_sta_mac_table = ksz8795_r_sta_mac_table,
1287        .w_sta_mac_table = ksz8795_w_sta_mac_table,
1288        .r_mib_cnt = ksz8795_r_mib_cnt,
1289        .r_mib_pkt = ksz8795_r_mib_pkt,
1290        .freeze_mib = ksz8795_freeze_mib,
1291        .port_init_cnt = ksz8795_port_init_cnt,
1292        .shutdown = ksz8795_reset_switch,
1293        .detect = ksz8795_switch_detect,
1294        .init = ksz8795_switch_init,
1295        .exit = ksz8795_switch_exit,
1296};
1297
1298int ksz8795_switch_register(struct ksz_device *dev)
1299{
1300        return ksz_switch_register(dev, &ksz8795_dev_ops);
1301}
1302EXPORT_SYMBOL(ksz8795_switch_register);
1303
1304MODULE_AUTHOR("Tristram Ha <Tristram.Ha@microchip.com>");
1305MODULE_DESCRIPTION("Microchip KSZ8795 Series Switch DSA Driver");
1306MODULE_LICENSE("GPL");
1307