// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * GE PPC9A board support
 *
 * Author: Martyn Welch <martyn.welch@ge.com>
 *
 * Copyright 2008 GE Intelligent Platforms Embedded Systems, Inc.
 *
 * Based on: mpc86xx_hpcn.c (MPC86xx HPCN board specific routines)
 * Copyright 2006 Freescale Semiconductor Inc.
 *
 * NEC fixup adapted from arch/mips/pci/fixup-lm2e.c
 */

#include <linux/stddef.h>
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/kdev_t.h>
#include <linux/delay.h>
#include <linux/seq_file.h>
#include <linux/of_platform.h>

#include <asm/time.h>
#include <asm/machdep.h>
#include <asm/pci-bridge.h>
#include <asm/prom.h>
#include <mm/mmu_decl.h>
#include <asm/udbg.h>

#include <asm/mpic.h>
#include <asm/nvram.h>

#include <sysdev/fsl_pci.h>
#include <sysdev/fsl_soc.h>
#include <sysdev/ge/ge_pic.h>

#include "mpc86xx.h"

#undef DEBUG

#ifdef DEBUG
#define DBG (fmt...) do { printk(KERN_ERR "PPC9A: " fmt); } while (0)
#else
#define DBG (fmt...) do { } while (0)
#endif

void __iomem *ppc9a_regs;

static void __init gef_ppc9a_init_irq(void)
{
        struct device_node *cascade_node = NULL;

        mpc86xx_init_irq();

        /*
         * There is a simple interrupt handler in the main FPGA, this needs
         * to be cascaded into the MPIC
         */
        cascade_node = of_find_compatible_node(NULL, NULL, "gef,fpga-pic-1.00");
        if (!cascade_node) {
                printk(KERN_WARNING "PPC9A: No FPGA PIC\n");
                return;
        }

        gef_pic_init(cascade_node);
        of_node_put(cascade_node);
}

static void __init gef_ppc9a_setup_arch(void)
{
        struct device_node *regs;

        printk(KERN_INFO "GE Intelligent Platforms PPC9A 6U VME SBC\n");

#ifdef CONFIG_SMP
        mpc86xx_smp_init();
#endif

        fsl_pci_assign_primary();

        /* Remap basic board registers */
        regs = of_find_compatible_node(NULL, NULL, "gef,ppc9a-fpga-regs");
        if (regs) {
                ppc9a_regs = of_iomap(regs, 0);
                if (ppc9a_regs == NULL)
                        printk(KERN_WARNING "Unable to map board registers\n");
                of_node_put(regs);
        }

#if defined(CONFIG_MMIO_NVRAM)
        mmio_nvram_init();
#endif
}

/* Return the PCB revision */
static unsigned int gef_ppc9a_get_pcb_rev(void)
{
        unsigned int reg;

        reg = ioread32be(ppc9a_regs);
        return (reg >> 16) & 0xff;
}

/* Return the board (software) revision */
static unsigned int gef_ppc9a_get_board_rev(void)
{
        unsigned int reg;

        reg = ioread32be(ppc9a_regs);
        return (reg >> 8) & 0xff;
}

/* Return the FPGA revision */
static unsigned int gef_ppc9a_get_fpga_rev(void)
{
        unsigned int reg;

        reg = ioread32be(ppc9a_regs);
        return reg & 0xf;
}

/* Return VME Geographical Address */
static unsigned int gef_ppc9a_get_vme_geo_addr(void)
{
        unsigned int reg;

        reg = ioread32be(ppc9a_regs + 0x4);
        return reg & 0x1f;
}

/* Return VME System Controller Status */
static unsigned int gef_ppc9a_get_vme_is_syscon(void)
{
        unsigned int reg;

        reg = ioread32be(ppc9a_regs + 0x4);
        return (reg >> 9) & 0x1;
}

static void gef_ppc9a_show_cpuinfo(struct seq_file *m)
{
        uint svid = mfspr(SPRN_SVR);

        seq_printf(m, "Vendor\t\t: GE Intelligent Platforms\n");

        seq_printf(m, "Revision\t: %u%c\n", gef_ppc9a_get_pcb_rev(),
                ('A' + gef_ppc9a_get_board_rev()));
        seq_printf(m, "FPGA Revision\t: %u\n", gef_ppc9a_get_fpga_rev());

        seq_printf(m, "SVR\t\t: 0x%x\n", svid);

        seq_printf(m, "VME geo. addr\t: %u\n", gef_ppc9a_get_vme_geo_addr());

        seq_printf(m, "VME syscon\t: %s\n",
                gef_ppc9a_get_vme_is_syscon() ? "yes" : "no");
}

static void gef_ppc9a_nec_fixup(struct pci_dev *pdev)
{
        unsigned int val;

        /* Do not do the fixup on other platforms! */
        if (!machine_is(gef_ppc9a))
                return;

        printk(KERN_INFO "Running NEC uPD720101 Fixup\n");

        /* Ensure ports 1, 2, 3, 4 & 5 are enabled */
        pci_read_config_dword(pdev, 0xe0, &val);
        pci_write_config_dword(pdev, 0xe0, (val & ~7) | 0x5);

        /* System clock is 48-MHz Oscillator and EHCI Enabled. */
        pci_write_config_dword(pdev, 0xe4, 1 << 5);
}
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_USB,
        gef_ppc9a_nec_fixup);

/*
 * Called very early, device-tree isn't unflattened
 *
 * This function is called to determine whether the BSP is compatible with the
 * supplied device-tree, which is assumed to be the correct one for the actual
 * board. It is expected thati, in the future, a kernel may support multiple
 * boards.
 */
static int __init gef_ppc9a_probe(void)
{
        if (of_machine_is_compatible("gef,ppc9a"))
                return 1;

        return 0;
}

machine_arch_initcall(gef_ppc9a, mpc86xx_common_publish_devices);

define_machine(gef_ppc9a) {
        .name                   = "GE PPC9A",
        .probe                  = gef_ppc9a_probe,
        .setup_arch             = gef_ppc9a_setup_arch,
        .init_IRQ               = gef_ppc9a_init_irq,
        .show_cpuinfo           = gef_ppc9a_show_cpuinfo,
        .get_irq                = mpic_get_irq,
        .time_init              = mpc86xx_time_init,
        .calibrate_decr         = generic_calibrate_decr,
        .progress               = udbg_progress,
#ifdef CONFIG_PCI
        .pcibios_fixup_bus      = fsl_pcibios_fixup_bus,
#endif
};