LXR linux/drivers/clocksource/timer-u300.c

   1// SPDX-License-Identifier: GPL-2.0-only
   2/*
   3 * Copyright (C) 2007-2009 ST-Ericsson AB
   4 * Timer COH 901 328, runs the OS timer interrupt.
   5 * Author: Linus Walleij <linus.walleij@stericsson.com>
   6 */
   7#include <linux/interrupt.h>
   8#include <linux/time.h>
   9#include <linux/timex.h>
  10#include <linux/clockchips.h>
  11#include <linux/clocksource.h>
  12#include <linux/types.h>
  13#include <linux/io.h>
  14#include <linux/clk.h>
  15#include <linux/err.h>
  16#include <linux/irq.h>
  17#include <linux/delay.h>
  18#include <linux/of_address.h>
  19#include <linux/of_irq.h>
  20#include <linux/sched_clock.h>
  21
  22/* Generic stuff */
  23#include <asm/mach/map.h>
  24#include <asm/mach/time.h>
  25
  26/*
  27 * APP side special timer registers
  28 * This timer contains four timers which can fire an interrupt each.
  29 * OS (operating system) timer @ 32768 Hz
  30 * DD (device driver) timer @ 1 kHz
  31 * GP1 (general purpose 1) timer @ 1MHz
  32 * GP2 (general purpose 2) timer @ 1MHz
  33 */
  34
  35/* Reset OS Timer 32bit (-/W) */
  36#define U300_TIMER_APP_ROST                                     (0x0000)
  37#define U300_TIMER_APP_ROST_TIMER_RESET                         (0x00000000)
  38/* Enable OS Timer 32bit (-/W) */
  39#define U300_TIMER_APP_EOST                                     (0x0004)
  40#define U300_TIMER_APP_EOST_TIMER_ENABLE                        (0x00000000)
  41/* Disable OS Timer 32bit (-/W) */
  42#define U300_TIMER_APP_DOST                                     (0x0008)
  43#define U300_TIMER_APP_DOST_TIMER_DISABLE                       (0x00000000)
  44/* OS Timer Mode Register 32bit (-/W) */
  45#define U300_TIMER_APP_SOSTM                                    (0x000c)
  46#define U300_TIMER_APP_SOSTM_MODE_CONTINUOUS                    (0x00000000)
  47#define U300_TIMER_APP_SOSTM_MODE_ONE_SHOT                      (0x00000001)
  48/* OS Timer Status Register 32bit (R/-) */
  49#define U300_TIMER_APP_OSTS                                     (0x0010)
  50#define U300_TIMER_APP_OSTS_TIMER_STATE_MASK                    (0x0000000F)
  51#define U300_TIMER_APP_OSTS_TIMER_STATE_IDLE                    (0x00000001)
  52#define U300_TIMER_APP_OSTS_TIMER_STATE_ACTIVE                  (0x00000002)
  53#define U300_TIMER_APP_OSTS_ENABLE_IND                          (0x00000010)
  54#define U300_TIMER_APP_OSTS_MODE_MASK                           (0x00000020)
  55#define U300_TIMER_APP_OSTS_MODE_CONTINUOUS                     (0x00000000)
  56#define U300_TIMER_APP_OSTS_MODE_ONE_SHOT                       (0x00000020)
  57#define U300_TIMER_APP_OSTS_IRQ_ENABLED_IND                     (0x00000040)
  58#define U300_TIMER_APP_OSTS_IRQ_PENDING_IND                     (0x00000080)
  59/* OS Timer Current Count Register 32bit (R/-) */
  60#define U300_TIMER_APP_OSTCC                                    (0x0014)
  61/* OS Timer Terminal Count Register 32bit (R/W) */
  62#define U300_TIMER_APP_OSTTC                                    (0x0018)
  63/* OS Timer Interrupt Enable Register 32bit (-/W) */
  64#define U300_TIMER_APP_OSTIE                                    (0x001c)
  65#define U300_TIMER_APP_OSTIE_IRQ_DISABLE                        (0x00000000)
  66#define U300_TIMER_APP_OSTIE_IRQ_ENABLE                         (0x00000001)
  67/* OS Timer Interrupt Acknowledge Register 32bit (-/W) */
  68#define U300_TIMER_APP_OSTIA                                    (0x0020)
  69#define U300_TIMER_APP_OSTIA_IRQ_ACK                            (0x00000080)
  70
  71/* Reset DD Timer 32bit (-/W) */
  72#define U300_TIMER_APP_RDDT                                     (0x0040)
  73#define U300_TIMER_APP_RDDT_TIMER_RESET                         (0x00000000)
  74/* Enable DD Timer 32bit (-/W) */
  75#define U300_TIMER_APP_EDDT                                     (0x0044)
  76#define U300_TIMER_APP_EDDT_TIMER_ENABLE                        (0x00000000)
  77/* Disable DD Timer 32bit (-/W) */
  78#define U300_TIMER_APP_DDDT                                     (0x0048)
  79#define U300_TIMER_APP_DDDT_TIMER_DISABLE                       (0x00000000)
  80/* DD Timer Mode Register 32bit (-/W) */
  81#define U300_TIMER_APP_SDDTM                                    (0x004c)
  82#define U300_TIMER_APP_SDDTM_MODE_CONTINUOUS                    (0x00000000)
  83#define U300_TIMER_APP_SDDTM_MODE_ONE_SHOT                      (0x00000001)
  84/* DD Timer Status Register 32bit (R/-) */
  85#define U300_TIMER_APP_DDTS                                     (0x0050)
  86#define U300_TIMER_APP_DDTS_TIMER_STATE_MASK                    (0x0000000F)
  87#define U300_TIMER_APP_DDTS_TIMER_STATE_IDLE                    (0x00000001)
  88#define U300_TIMER_APP_DDTS_TIMER_STATE_ACTIVE                  (0x00000002)
  89#define U300_TIMER_APP_DDTS_ENABLE_IND                          (0x00000010)
  90#define U300_TIMER_APP_DDTS_MODE_MASK                           (0x00000020)
  91#define U300_TIMER_APP_DDTS_MODE_CONTINUOUS                     (0x00000000)
  92#define U300_TIMER_APP_DDTS_MODE_ONE_SHOT                       (0x00000020)
  93#define U300_TIMER_APP_DDTS_IRQ_ENABLED_IND                     (0x00000040)
  94#define U300_TIMER_APP_DDTS_IRQ_PENDING_IND                     (0x00000080)
  95/* DD Timer Current Count Register 32bit (R/-) */
  96#define U300_TIMER_APP_DDTCC                                    (0x0054)
  97/* DD Timer Terminal Count Register 32bit (R/W) */
  98#define U300_TIMER_APP_DDTTC                                    (0x0058)
  99/* DD Timer Interrupt Enable Register 32bit (-/W) */
 100#define U300_TIMER_APP_DDTIE                                    (0x005c)
 101#define U300_TIMER_APP_DDTIE_IRQ_DISABLE                        (0x00000000)
 102#define U300_TIMER_APP_DDTIE_IRQ_ENABLE                         (0x00000001)
 103/* DD Timer Interrupt Acknowledge Register 32bit (-/W) */
 104#define U300_TIMER_APP_DDTIA                                    (0x0060)
 105#define U300_TIMER_APP_DDTIA_IRQ_ACK                            (0x00000080)
 106
 107/* Reset GP1 Timer 32bit (-/W) */
 108#define U300_TIMER_APP_RGPT1                                    (0x0080)
 109#define U300_TIMER_APP_RGPT1_TIMER_RESET                        (0x00000000)
 110/* Enable GP1 Timer 32bit (-/W) */
 111#define U300_TIMER_APP_EGPT1                                    (0x0084)
 112#define U300_TIMER_APP_EGPT1_TIMER_ENABLE                       (0x00000000)
 113/* Disable GP1 Timer 32bit (-/W) */
 114#define U300_TIMER_APP_DGPT1                                    (0x0088)
 115#define U300_TIMER_APP_DGPT1_TIMER_DISABLE                      (0x00000000)
 116/* GP1 Timer Mode Register 32bit (-/W) */
 117#define U300_TIMER_APP_SGPT1M                                   (0x008c)
 118#define U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS                   (0x00000000)
 119#define U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT                     (0x00000001)
 120/* GP1 Timer Status Register 32bit (R/-) */
 121#define U300_TIMER_APP_GPT1S                                    (0x0090)
 122#define U300_TIMER_APP_GPT1S_TIMER_STATE_MASK                   (0x0000000F)
 123#define U300_TIMER_APP_GPT1S_TIMER_STATE_IDLE                   (0x00000001)
 124#define U300_TIMER_APP_GPT1S_TIMER_STATE_ACTIVE                 (0x00000002)
 125#define U300_TIMER_APP_GPT1S_ENABLE_IND                         (0x00000010)
 126#define U300_TIMER_APP_GPT1S_MODE_MASK                          (0x00000020)
 127#define U300_TIMER_APP_GPT1S_MODE_CONTINUOUS                    (0x00000000)
 128#define U300_TIMER_APP_GPT1S_MODE_ONE_SHOT                      (0x00000020)
 129#define U300_TIMER_APP_GPT1S_IRQ_ENABLED_IND                    (0x00000040)
 130#define U300_TIMER_APP_GPT1S_IRQ_PENDING_IND                    (0x00000080)
 131/* GP1 Timer Current Count Register 32bit (R/-) */
 132#define U300_TIMER_APP_GPT1CC                                   (0x0094)
 133/* GP1 Timer Terminal Count Register 32bit (R/W) */
 134#define U300_TIMER_APP_GPT1TC                                   (0x0098)
 135/* GP1 Timer Interrupt Enable Register 32bit (-/W) */
 136#define U300_TIMER_APP_GPT1IE                                   (0x009c)
 137#define U300_TIMER_APP_GPT1IE_IRQ_DISABLE                       (0x00000000)
 138#define U300_TIMER_APP_GPT1IE_IRQ_ENABLE                        (0x00000001)
 139/* GP1 Timer Interrupt Acknowledge Register 32bit (-/W) */
 140#define U300_TIMER_APP_GPT1IA                                   (0x00a0)
 141#define U300_TIMER_APP_GPT1IA_IRQ_ACK                           (0x00000080)
 142
 143/* Reset GP2 Timer 32bit (-/W) */
 144#define U300_TIMER_APP_RGPT2                                    (0x00c0)
 145#define U300_TIMER_APP_RGPT2_TIMER_RESET                        (0x00000000)
 146/* Enable GP2 Timer 32bit (-/W) */
 147#define U300_TIMER_APP_EGPT2                                    (0x00c4)
 148#define U300_TIMER_APP_EGPT2_TIMER_ENABLE                       (0x00000000)
 149/* Disable GP2 Timer 32bit (-/W) */
 150#define U300_TIMER_APP_DGPT2                                    (0x00c8)
 151#define U300_TIMER_APP_DGPT2_TIMER_DISABLE                      (0x00000000)
 152/* GP2 Timer Mode Register 32bit (-/W) */
 153#define U300_TIMER_APP_SGPT2M                                   (0x00cc)
 154#define U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS                   (0x00000000)
 155#define U300_TIMER_APP_SGPT2M_MODE_ONE_SHOT                     (0x00000001)
 156/* GP2 Timer Status Register 32bit (R/-) */
 157#define U300_TIMER_APP_GPT2S                                    (0x00d0)
 158#define U300_TIMER_APP_GPT2S_TIMER_STATE_MASK                   (0x0000000F)
 159#define U300_TIMER_APP_GPT2S_TIMER_STATE_IDLE                   (0x00000001)
 160#define U300_TIMER_APP_GPT2S_TIMER_STATE_ACTIVE                 (0x00000002)
 161#define U300_TIMER_APP_GPT2S_ENABLE_IND                         (0x00000010)
 162#define U300_TIMER_APP_GPT2S_MODE_MASK                          (0x00000020)
 163#define U300_TIMER_APP_GPT2S_MODE_CONTINUOUS                    (0x00000000)
 164#define U300_TIMER_APP_GPT2S_MODE_ONE_SHOT                      (0x00000020)
 165#define U300_TIMER_APP_GPT2S_IRQ_ENABLED_IND                    (0x00000040)
 166#define U300_TIMER_APP_GPT2S_IRQ_PENDING_IND                    (0x00000080)
 167/* GP2 Timer Current Count Register 32bit (R/-) */
 168#define U300_TIMER_APP_GPT2CC                                   (0x00d4)
 169/* GP2 Timer Terminal Count Register 32bit (R/W) */
 170#define U300_TIMER_APP_GPT2TC                                   (0x00d8)
 171/* GP2 Timer Interrupt Enable Register 32bit (-/W) */
 172#define U300_TIMER_APP_GPT2IE                                   (0x00dc)
 173#define U300_TIMER_APP_GPT2IE_IRQ_DISABLE                       (0x00000000)
 174#define U300_TIMER_APP_GPT2IE_IRQ_ENABLE                        (0x00000001)
 175/* GP2 Timer Interrupt Acknowledge Register 32bit (-/W) */
 176#define U300_TIMER_APP_GPT2IA                                   (0x00e0)
 177#define U300_TIMER_APP_GPT2IA_IRQ_ACK                           (0x00000080)
 178
 179/* Clock request control register - all four timers */
 180#define U300_TIMER_APP_CRC                                      (0x100)
 181#define U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE                 (0x00000001)
 182
 183static void __iomem *u300_timer_base;
 184
 185struct u300_clockevent_data {
 186        struct clock_event_device cevd;
 187        unsigned ticks_per_jiffy;
 188};
 189
 190static int u300_shutdown(struct clock_event_device *evt)
 191{
 192        /* Disable interrupts on GP1 */
 193        writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
 194               u300_timer_base + U300_TIMER_APP_GPT1IE);
 195        /* Disable GP1 */
 196        writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
 197               u300_timer_base + U300_TIMER_APP_DGPT1);
 198        return 0;
 199}
 200
 201/*
 202 * If we have oneshot timer active, the oneshot scheduling function
 203 * u300_set_next_event() is called immediately after.
 204 */
 205static int u300_set_oneshot(struct clock_event_device *evt)
 206{
 207        /* Just return; here? */
 208        /*
 209         * The actual event will be programmed by the next event hook,
 210         * so we just set a dummy value somewhere at the end of the
 211         * universe here.
 212         */
 213        /* Disable interrupts on GPT1 */
 214        writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
 215               u300_timer_base + U300_TIMER_APP_GPT1IE);
 216        /* Disable GP1 while we're reprogramming it. */
 217        writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
 218               u300_timer_base + U300_TIMER_APP_DGPT1);
 219        /*
 220         * Expire far in the future, u300_set_next_event() will be
 221         * called soon...
 222         */
 223        writel(0xFFFFFFFF, u300_timer_base + U300_TIMER_APP_GPT1TC);
 224        /* We run one shot per tick here! */
 225        writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT,
 226               u300_timer_base + U300_TIMER_APP_SGPT1M);
 227        /* Enable interrupts for this timer */
 228        writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
 229               u300_timer_base + U300_TIMER_APP_GPT1IE);
 230        /* Enable timer */
 231        writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
 232               u300_timer_base + U300_TIMER_APP_EGPT1);
 233        return 0;
 234}
 235
 236static int u300_set_periodic(struct clock_event_device *evt)
 237{
 238        struct u300_clockevent_data *cevdata =
 239                container_of(evt, struct u300_clockevent_data, cevd);
 240
 241        /* Disable interrupts on GPT1 */
 242        writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
 243               u300_timer_base + U300_TIMER_APP_GPT1IE);
 244        /* Disable GP1 while we're reprogramming it. */
 245        writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
 246               u300_timer_base + U300_TIMER_APP_DGPT1);
 247        /*
 248         * Set the periodic mode to a certain number of ticks per
 249         * jiffy.
 250         */
 251        writel(cevdata->ticks_per_jiffy,
 252               u300_timer_base + U300_TIMER_APP_GPT1TC);
 253        /*
 254         * Set continuous mode, so the timer keeps triggering
 255         * interrupts.
 256         */
 257        writel(U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS,
 258               u300_timer_base + U300_TIMER_APP_SGPT1M);
 259        /* Enable timer interrupts */
 260        writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
 261               u300_timer_base + U300_TIMER_APP_GPT1IE);
 262        /* Then enable the OS timer again */
 263        writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
 264               u300_timer_base + U300_TIMER_APP_EGPT1);
 265        return 0;
 266}
 267
 268/*
 269 * The app timer in one shot mode obviously has to be reprogrammed
 270 * in EXACTLY this sequence to work properly. Do NOT try to e.g. replace
 271 * the interrupt disable + timer disable commands with a reset command,
 272 * it will fail miserably. Apparently (and I found this the hard way)
 273 * the timer is very sensitive to the instruction order, though you don't
 274 * get that impression from the data sheet.
 275 */
 276static int u300_set_next_event(unsigned long cycles,
 277                               struct clock_event_device *evt)
 278
 279{
 280        /* Disable interrupts on GPT1 */
 281        writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
 282               u300_timer_base + U300_TIMER_APP_GPT1IE);
 283        /* Disable GP1 while we're reprogramming it. */
 284        writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
 285               u300_timer_base + U300_TIMER_APP_DGPT1);
 286        /* Reset the General Purpose timer 1. */
 287        writel(U300_TIMER_APP_RGPT1_TIMER_RESET,
 288               u300_timer_base + U300_TIMER_APP_RGPT1);
 289        /* IRQ in n * cycles */
 290        writel(cycles, u300_timer_base + U300_TIMER_APP_GPT1TC);
 291        /*
 292         * We run one shot per tick here! (This is necessary to reconfigure,
 293         * the timer will tilt if you don't!)
 294         */
 295        writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT,
 296               u300_timer_base + U300_TIMER_APP_SGPT1M);
 297        /* Enable timer interrupts */
 298        writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
 299               u300_timer_base + U300_TIMER_APP_GPT1IE);
 300        /* Then enable the OS timer again */
 301        writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
 302               u300_timer_base + U300_TIMER_APP_EGPT1);
 303        return 0;
 304}
 305
 306static struct u300_clockevent_data u300_clockevent_data = {
 307        /* Use general purpose timer 1 as clock event */
 308        .cevd = {
 309                .name                   = "GPT1",
 310                /* Reasonably fast and accurate clock event */
 311                .rating                 = 300,
 312                .features               = CLOCK_EVT_FEAT_PERIODIC |
 313                                          CLOCK_EVT_FEAT_ONESHOT,
 314                .set_next_event         = u300_set_next_event,
 315                .set_state_shutdown     = u300_shutdown,
 316                .set_state_periodic     = u300_set_periodic,
 317                .set_state_oneshot      = u300_set_oneshot,
 318        },
 319};
 320
 321/* Clock event timer interrupt handler */
 322static irqreturn_t u300_timer_interrupt(int irq, void *dev_id)
 323{
 324        struct clock_event_device *evt = &u300_clockevent_data.cevd;
 325        /* ACK/Clear timer IRQ for the APP GPT1 Timer */
 326
 327        writel(U300_TIMER_APP_GPT1IA_IRQ_ACK,
 328                u300_timer_base + U300_TIMER_APP_GPT1IA);
 329        evt->event_handler(evt);
 330        return IRQ_HANDLED;
 331}
 332
 333/*
 334 * Override the global weak sched_clock symbol with this
 335 * local implementation which uses the clocksource to get some
 336 * better resolution when scheduling the kernel. We accept that
 337 * this wraps around for now, since it is just a relative time
 338 * stamp. (Inspired by OMAP implementation.)
 339 */
 340
 341static u64 notrace u300_read_sched_clock(void)
 342{
 343        return readl(u300_timer_base + U300_TIMER_APP_GPT2CC);
 344}
 345
 346static unsigned long u300_read_current_timer(void)
 347{
 348        return readl(u300_timer_base + U300_TIMER_APP_GPT2CC);
 349}
 350
 351static struct delay_timer u300_delay_timer;
 352
 353/*
 354 * This sets up the system timers, clock source and clock event.
 355 */
 356static int __init u300_timer_init_of(struct device_node *np)
 357{
 358        unsigned int irq;
 359        struct clk *clk;
 360        unsigned long rate;
 361        int ret;
 362
 363        u300_timer_base = of_iomap(np, 0);
 364        if (!u300_timer_base) {
 365                pr_err("could not ioremap system timer\n");
 366                return -ENXIO;
 367        }
 368
 369        /* Get the IRQ for the GP1 timer */
 370        irq = irq_of_parse_and_map(np, 2);
 371        if (!irq) {
 372                pr_err("no IRQ for system timer\n");
 373                return -EINVAL;
 374        }
 375
 376        pr_info("U300 GP1 timer @ base: %p, IRQ: %u\n", u300_timer_base, irq);
 377
 378        /* Clock the interrupt controller */
 379        clk = of_clk_get(np, 0);
 380        if (IS_ERR(clk))
 381                return PTR_ERR(clk);
 382
 383        ret = clk_prepare_enable(clk);
 384        if (ret)
 385                return ret;
 386
 387        rate = clk_get_rate(clk);
 388
 389        u300_clockevent_data.ticks_per_jiffy = DIV_ROUND_CLOSEST(rate, HZ);
 390
 391        sched_clock_register(u300_read_sched_clock, 32, rate);
 392
 393        u300_delay_timer.read_current_timer = &u300_read_current_timer;
 394        u300_delay_timer.freq = rate;
 395        register_current_timer_delay(&u300_delay_timer);
 396
 397        /*
 398         * Disable the "OS" and "DD" timers - these are designed for Symbian!
 399         * Example usage in cnh1601578 cpu subsystem pd_timer_app.c
 400         */
 401        writel(U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE,
 402                u300_timer_base + U300_TIMER_APP_CRC);
 403        writel(U300_TIMER_APP_ROST_TIMER_RESET,
 404                u300_timer_base + U300_TIMER_APP_ROST);
 405        writel(U300_TIMER_APP_DOST_TIMER_DISABLE,
 406                u300_timer_base + U300_TIMER_APP_DOST);
 407        writel(U300_TIMER_APP_RDDT_TIMER_RESET,
 408                u300_timer_base + U300_TIMER_APP_RDDT);
 409        writel(U300_TIMER_APP_DDDT_TIMER_DISABLE,
 410                u300_timer_base + U300_TIMER_APP_DDDT);
 411
 412        /* Reset the General Purpose timer 1. */
 413        writel(U300_TIMER_APP_RGPT1_TIMER_RESET,
 414                u300_timer_base + U300_TIMER_APP_RGPT1);
 415
 416        /* Set up the IRQ handler */
 417        ret = request_irq(irq, u300_timer_interrupt,
 418                          IRQF_TIMER | IRQF_IRQPOLL, "U300 Timer Tick", NULL);
 419        if (ret)
 420                return ret;
 421
 422        /* Reset the General Purpose timer 2 */
 423        writel(U300_TIMER_APP_RGPT2_TIMER_RESET,
 424                u300_timer_base + U300_TIMER_APP_RGPT2);
 425        /* Set this timer to run around forever */
 426        writel(0xFFFFFFFFU, u300_timer_base + U300_TIMER_APP_GPT2TC);
 427        /* Set continuous mode so it wraps around */
 428        writel(U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS,
 429               u300_timer_base + U300_TIMER_APP_SGPT2M);
 430        /* Disable timer interrupts */
 431        writel(U300_TIMER_APP_GPT2IE_IRQ_DISABLE,
 432                u300_timer_base + U300_TIMER_APP_GPT2IE);
 433        /* Then enable the GP2 timer to use as a free running us counter */
 434        writel(U300_TIMER_APP_EGPT2_TIMER_ENABLE,
 435                u300_timer_base + U300_TIMER_APP_EGPT2);
 436
 437        /* Use general purpose timer 2 as clock source */
 438        ret = clocksource_mmio_init(u300_timer_base + U300_TIMER_APP_GPT2CC,
 439                                    "GPT2", rate, 300, 32, clocksource_mmio_readl_up);
 440        if (ret) {
 441                pr_err("timer: failed to initialize U300 clock source\n");
 442                return ret;
 443        }
 444
 445        /* Configure and register the clockevent */
 446        clockevents_config_and_register(&u300_clockevent_data.cevd, rate,
 447                                        1, 0xffffffff);
 448
 449        /*
 450         * TODO: init and register the rest of the timers too, they can be
 451         * used by hrtimers!
 452         */
 453        return 0;
 454}
 455
 456TIMER_OF_DECLARE(u300_timer, "stericsson,u300-apptimer",
 457                       u300_timer_init_of);
 458