linux/drivers/hwmon/w83792d.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0-or-later
   2/*
   3 * w83792d.c - Part of lm_sensors, Linux kernel modules for hardware
   4 *             monitoring
   5 * Copyright (C) 2004, 2005 Winbond Electronics Corp.
   6 *                          Shane Huang,
   7 *                          Rudolf Marek <r.marek@assembler.cz>
   8 *
   9 * Note:
  10 * 1. This driver is only for 2.6 kernel, 2.4 kernel need a different driver.
  11 * 2. This driver is only for Winbond W83792D C version device, there
  12 *     are also some motherboards with B version W83792D device. The
  13 *     calculation method to in6-in7(measured value, limits) is a little
  14 *     different between C and B version. C or B version can be identified
  15 *     by CR[0x49h].
  16 */
  17
  18/*
  19 * Supports following chips:
  20 *
  21 * Chip         #vin    #fanin  #pwm    #temp   wchipid vendid  i2c     ISA
  22 * w83792d      9       7       7       3       0x7a    0x5ca3  yes     no
  23 */
  24
  25#include <linux/module.h>
  26#include <linux/init.h>
  27#include <linux/slab.h>
  28#include <linux/i2c.h>
  29#include <linux/hwmon.h>
  30#include <linux/hwmon-sysfs.h>
  31#include <linux/err.h>
  32#include <linux/mutex.h>
  33#include <linux/sysfs.h>
  34#include <linux/jiffies.h>
  35
  36/* Addresses to scan */
  37static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f,
  38                                                I2C_CLIENT_END };
  39
  40/* Insmod parameters */
  41
  42static unsigned short force_subclients[4];
  43module_param_array(force_subclients, short, NULL, 0);
  44MODULE_PARM_DESC(force_subclients,
  45                 "List of subclient addresses: {bus, clientaddr, subclientaddr1, subclientaddr2}");
  46
  47static bool init;
  48module_param(init, bool, 0);
  49MODULE_PARM_DESC(init, "Set to one to force chip initialization");
  50
  51/* The W83792D registers */
  52static const u8 W83792D_REG_IN[9] = {
  53        0x20,   /* Vcore A in DataSheet */
  54        0x21,   /* Vcore B in DataSheet */
  55        0x22,   /* VIN0 in DataSheet */
  56        0x23,   /* VIN1 in DataSheet */
  57        0x24,   /* VIN2 in DataSheet */
  58        0x25,   /* VIN3 in DataSheet */
  59        0x26,   /* 5VCC in DataSheet */
  60        0xB0,   /* 5VSB in DataSheet */
  61        0xB1    /* VBAT in DataSheet */
  62};
  63#define W83792D_REG_LOW_BITS1 0x3E  /* Low Bits I in DataSheet */
  64#define W83792D_REG_LOW_BITS2 0x3F  /* Low Bits II in DataSheet */
  65static const u8 W83792D_REG_IN_MAX[9] = {
  66        0x2B,   /* Vcore A High Limit in DataSheet */
  67        0x2D,   /* Vcore B High Limit in DataSheet */
  68        0x2F,   /* VIN0 High Limit in DataSheet */
  69        0x31,   /* VIN1 High Limit in DataSheet */
  70        0x33,   /* VIN2 High Limit in DataSheet */
  71        0x35,   /* VIN3 High Limit in DataSheet */
  72        0x37,   /* 5VCC High Limit in DataSheet */
  73        0xB4,   /* 5VSB High Limit in DataSheet */
  74        0xB6    /* VBAT High Limit in DataSheet */
  75};
  76static const u8 W83792D_REG_IN_MIN[9] = {
  77        0x2C,   /* Vcore A Low Limit in DataSheet */
  78        0x2E,   /* Vcore B Low Limit in DataSheet */
  79        0x30,   /* VIN0 Low Limit in DataSheet */
  80        0x32,   /* VIN1 Low Limit in DataSheet */
  81        0x34,   /* VIN2 Low Limit in DataSheet */
  82        0x36,   /* VIN3 Low Limit in DataSheet */
  83        0x38,   /* 5VCC Low Limit in DataSheet */
  84        0xB5,   /* 5VSB Low Limit in DataSheet */
  85        0xB7    /* VBAT Low Limit in DataSheet */
  86};
  87static const u8 W83792D_REG_FAN[7] = {
  88        0x28,   /* FAN 1 Count in DataSheet */
  89        0x29,   /* FAN 2 Count in DataSheet */
  90        0x2A,   /* FAN 3 Count in DataSheet */
  91        0xB8,   /* FAN 4 Count in DataSheet */
  92        0xB9,   /* FAN 5 Count in DataSheet */
  93        0xBA,   /* FAN 6 Count in DataSheet */
  94        0xBE    /* FAN 7 Count in DataSheet */
  95};
  96static const u8 W83792D_REG_FAN_MIN[7] = {
  97        0x3B,   /* FAN 1 Count Low Limit in DataSheet */
  98        0x3C,   /* FAN 2 Count Low Limit in DataSheet */
  99        0x3D,   /* FAN 3 Count Low Limit in DataSheet */
 100        0xBB,   /* FAN 4 Count Low Limit in DataSheet */
 101        0xBC,   /* FAN 5 Count Low Limit in DataSheet */
 102        0xBD,   /* FAN 6 Count Low Limit in DataSheet */
 103        0xBF    /* FAN 7 Count Low Limit in DataSheet */
 104};
 105#define W83792D_REG_FAN_CFG 0x84        /* FAN Configuration in DataSheet */
 106static const u8 W83792D_REG_FAN_DIV[4] = {
 107        0x47,   /* contains FAN2 and FAN1 Divisor */
 108        0x5B,   /* contains FAN4 and FAN3 Divisor */
 109        0x5C,   /* contains FAN6 and FAN5 Divisor */
 110        0x9E    /* contains FAN7 Divisor. */
 111};
 112static const u8 W83792D_REG_PWM[7] = {
 113        0x81,   /* FAN 1 Duty Cycle, be used to control */
 114        0x83,   /* FAN 2 Duty Cycle, be used to control */
 115        0x94,   /* FAN 3 Duty Cycle, be used to control */
 116        0xA3,   /* FAN 4 Duty Cycle, be used to control */
 117        0xA4,   /* FAN 5 Duty Cycle, be used to control */
 118        0xA5,   /* FAN 6 Duty Cycle, be used to control */
 119        0xA6    /* FAN 7 Duty Cycle, be used to control */
 120};
 121#define W83792D_REG_BANK                0x4E
 122#define W83792D_REG_TEMP2_CONFIG        0xC2
 123#define W83792D_REG_TEMP3_CONFIG        0xCA
 124
 125static const u8 W83792D_REG_TEMP1[3] = {
 126        0x27,   /* TEMP 1 in DataSheet */
 127        0x39,   /* TEMP 1 Over in DataSheet */
 128        0x3A,   /* TEMP 1 Hyst in DataSheet */
 129};
 130
 131static const u8 W83792D_REG_TEMP_ADD[2][6] = {
 132        { 0xC0,         /* TEMP 2 in DataSheet */
 133          0xC1,         /* TEMP 2(0.5 deg) in DataSheet */
 134          0xC5,         /* TEMP 2 Over High part in DataSheet */
 135          0xC6,         /* TEMP 2 Over Low part in DataSheet */
 136          0xC3,         /* TEMP 2 Thyst High part in DataSheet */
 137          0xC4 },       /* TEMP 2 Thyst Low part in DataSheet */
 138        { 0xC8,         /* TEMP 3 in DataSheet */
 139          0xC9,         /* TEMP 3(0.5 deg) in DataSheet */
 140          0xCD,         /* TEMP 3 Over High part in DataSheet */
 141          0xCE,         /* TEMP 3 Over Low part in DataSheet */
 142          0xCB,         /* TEMP 3 Thyst High part in DataSheet */
 143          0xCC }        /* TEMP 3 Thyst Low part in DataSheet */
 144};
 145
 146static const u8 W83792D_REG_THERMAL[3] = {
 147        0x85,   /* SmartFanI: Fan1 target value */
 148        0x86,   /* SmartFanI: Fan2 target value */
 149        0x96    /* SmartFanI: Fan3 target value */
 150};
 151
 152static const u8 W83792D_REG_TOLERANCE[3] = {
 153        0x87,   /* (bit3-0)SmartFan Fan1 tolerance */
 154        0x87,   /* (bit7-4)SmartFan Fan2 tolerance */
 155        0x97    /* (bit3-0)SmartFan Fan3 tolerance */
 156};
 157
 158static const u8 W83792D_REG_POINTS[3][4] = {
 159        { 0x85,         /* SmartFanII: Fan1 temp point 1 */
 160          0xE3,         /* SmartFanII: Fan1 temp point 2 */
 161          0xE4,         /* SmartFanII: Fan1 temp point 3 */
 162          0xE5 },       /* SmartFanII: Fan1 temp point 4 */
 163        { 0x86,         /* SmartFanII: Fan2 temp point 1 */
 164          0xE6,         /* SmartFanII: Fan2 temp point 2 */
 165          0xE7,         /* SmartFanII: Fan2 temp point 3 */
 166          0xE8 },       /* SmartFanII: Fan2 temp point 4 */
 167        { 0x96,         /* SmartFanII: Fan3 temp point 1 */
 168          0xE9,         /* SmartFanII: Fan3 temp point 2 */
 169          0xEA,         /* SmartFanII: Fan3 temp point 3 */
 170          0xEB }        /* SmartFanII: Fan3 temp point 4 */
 171};
 172
 173static const u8 W83792D_REG_LEVELS[3][4] = {
 174        { 0x88,         /* (bit3-0) SmartFanII: Fan1 Non-Stop */
 175          0x88,         /* (bit7-4) SmartFanII: Fan1 Level 1 */
 176          0xE0,         /* (bit7-4) SmartFanII: Fan1 Level 2 */
 177          0xE0 },       /* (bit3-0) SmartFanII: Fan1 Level 3 */
 178        { 0x89,         /* (bit3-0) SmartFanII: Fan2 Non-Stop */
 179          0x89,         /* (bit7-4) SmartFanII: Fan2 Level 1 */
 180          0xE1,         /* (bit7-4) SmartFanII: Fan2 Level 2 */
 181          0xE1 },       /* (bit3-0) SmartFanII: Fan2 Level 3 */
 182        { 0x98,         /* (bit3-0) SmartFanII: Fan3 Non-Stop */
 183          0x98,         /* (bit7-4) SmartFanII: Fan3 Level 1 */
 184          0xE2,         /* (bit7-4) SmartFanII: Fan3 Level 2 */
 185          0xE2 }        /* (bit3-0) SmartFanII: Fan3 Level 3 */
 186};
 187
 188#define W83792D_REG_GPIO_EN             0x1A
 189#define W83792D_REG_CONFIG              0x40
 190#define W83792D_REG_VID_FANDIV          0x47
 191#define W83792D_REG_CHIPID              0x49
 192#define W83792D_REG_WCHIPID             0x58
 193#define W83792D_REG_CHIPMAN             0x4F
 194#define W83792D_REG_PIN                 0x4B
 195#define W83792D_REG_I2C_SUBADDR         0x4A
 196
 197#define W83792D_REG_ALARM1 0xA9         /* realtime status register1 */
 198#define W83792D_REG_ALARM2 0xAA         /* realtime status register2 */
 199#define W83792D_REG_ALARM3 0xAB         /* realtime status register3 */
 200#define W83792D_REG_CHASSIS 0x42        /* Bit 5: Case Open status bit */
 201#define W83792D_REG_CHASSIS_CLR 0x44    /* Bit 7: Case Open CLR_CHS/Reset bit */
 202
 203/* control in0/in1 's limit modifiability */
 204#define W83792D_REG_VID_IN_B            0x17
 205
 206#define W83792D_REG_VBAT                0x5D
 207#define W83792D_REG_I2C_ADDR            0x48
 208
 209/*
 210 * Conversions. Rounding and limit checking is only done on the TO_REG
 211 * variants. Note that you should be a bit careful with which arguments
 212 * these macros are called: arguments may be evaluated more than once.
 213 * Fixing this is just not worth it.
 214 */
 215#define IN_FROM_REG(nr, val) (((nr) <= 1) ? ((val) * 2) : \
 216                ((((nr) == 6) || ((nr) == 7)) ? ((val) * 6) : ((val) * 4)))
 217#define IN_TO_REG(nr, val) (((nr) <= 1) ? ((val) / 2) : \
 218                ((((nr) == 6) || ((nr) == 7)) ? ((val) / 6) : ((val) / 4)))
 219
 220static inline u8
 221FAN_TO_REG(long rpm, int div)
 222{
 223        if (rpm == 0)
 224                return 255;
 225        rpm = clamp_val(rpm, 1, 1000000);
 226        return clamp_val((1350000 + rpm * div / 2) / (rpm * div), 1, 254);
 227}
 228
 229#define FAN_FROM_REG(val, div)  ((val) == 0   ? -1 : \
 230                                ((val) == 255 ? 0 : \
 231                                                1350000 / ((val) * (div))))
 232
 233/* for temp1 */
 234#define TEMP1_TO_REG(val)       (clamp_val(((val) < 0 ? (val) + 0x100 * 1000 \
 235                                                      : (val)) / 1000, 0, 0xff))
 236#define TEMP1_FROM_REG(val)     (((val) & 0x80 ? (val)-0x100 : (val)) * 1000)
 237/* for temp2 and temp3, because they need additional resolution */
 238#define TEMP_ADD_FROM_REG(val1, val2) \
 239        ((((val1) & 0x80 ? (val1)-0x100 \
 240                : (val1)) * 1000) + ((val2 & 0x80) ? 500 : 0))
 241#define TEMP_ADD_TO_REG_HIGH(val) \
 242        (clamp_val(((val) < 0 ? (val) + 0x100 * 1000 : (val)) / 1000, 0, 0xff))
 243#define TEMP_ADD_TO_REG_LOW(val)        ((val%1000) ? 0x80 : 0x00)
 244
 245#define DIV_FROM_REG(val)               (1 << (val))
 246
 247static inline u8
 248DIV_TO_REG(long val)
 249{
 250        int i;
 251        val = clamp_val(val, 1, 128) >> 1;
 252        for (i = 0; i < 7; i++) {
 253                if (val == 0)
 254                        break;
 255                val >>= 1;
 256        }
 257        return (u8)i;
 258}
 259
 260struct w83792d_data {
 261        struct device *hwmon_dev;
 262
 263        struct mutex update_lock;
 264        char valid;             /* !=0 if following fields are valid */
 265        unsigned long last_updated;     /* In jiffies */
 266
 267        /* array of 2 pointers to subclients */
 268        struct i2c_client *lm75[2];
 269
 270        u8 in[9];               /* Register value */
 271        u8 in_max[9];           /* Register value */
 272        u8 in_min[9];           /* Register value */
 273        u16 low_bits;           /* Additional resolution to voltage in6-0 */
 274        u8 fan[7];              /* Register value */
 275        u8 fan_min[7];          /* Register value */
 276        u8 temp1[3];            /* current, over, thyst */
 277        u8 temp_add[2][6];      /* Register value */
 278        u8 fan_div[7];          /* Register encoding, shifted right */
 279        u8 pwm[7];              /* The 7 PWM outputs */
 280        u8 pwmenable[3];
 281        u32 alarms;             /* realtime status register encoding,combined */
 282        u8 chassis;             /* Chassis status */
 283        u8 thermal_cruise[3];   /* Smart FanI: Fan1,2,3 target value */
 284        u8 tolerance[3];        /* Fan1,2,3 tolerance(Smart Fan I/II) */
 285        u8 sf2_points[3][4];    /* Smart FanII: Fan1,2,3 temperature points */
 286        u8 sf2_levels[3][4];    /* Smart FanII: Fan1,2,3 duty cycle levels */
 287};
 288
 289static int w83792d_probe(struct i2c_client *client,
 290                         const struct i2c_device_id *id);
 291static int w83792d_detect(struct i2c_client *client,
 292                          struct i2c_board_info *info);
 293static int w83792d_remove(struct i2c_client *client);
 294static struct w83792d_data *w83792d_update_device(struct device *dev);
 295
 296#ifdef DEBUG
 297static void w83792d_print_debug(struct w83792d_data *data, struct device *dev);
 298#endif
 299
 300static void w83792d_init_client(struct i2c_client *client);
 301
 302static const struct i2c_device_id w83792d_id[] = {
 303        { "w83792d", 0 },
 304        { }
 305};
 306MODULE_DEVICE_TABLE(i2c, w83792d_id);
 307
 308static struct i2c_driver w83792d_driver = {
 309        .class          = I2C_CLASS_HWMON,
 310        .driver = {
 311                .name = "w83792d",
 312        },
 313        .probe          = w83792d_probe,
 314        .remove         = w83792d_remove,
 315        .id_table       = w83792d_id,
 316        .detect         = w83792d_detect,
 317        .address_list   = normal_i2c,
 318};
 319
 320static inline long in_count_from_reg(int nr, struct w83792d_data *data)
 321{
 322        /* in7 and in8 do not have low bits, but the formula still works */
 323        return (data->in[nr] << 2) | ((data->low_bits >> (2 * nr)) & 0x03);
 324}
 325
 326/*
 327 * The SMBus locks itself. The Winbond W83792D chip has a bank register,
 328 * but the driver only accesses registers in bank 0, so we don't have
 329 * to switch banks and lock access between switches.
 330 */
 331static inline int w83792d_read_value(struct i2c_client *client, u8 reg)
 332{
 333        return i2c_smbus_read_byte_data(client, reg);
 334}
 335
 336static inline int
 337w83792d_write_value(struct i2c_client *client, u8 reg, u8 value)
 338{
 339        return i2c_smbus_write_byte_data(client, reg, value);
 340}
 341
 342/* following are the sysfs callback functions */
 343static ssize_t show_in(struct device *dev, struct device_attribute *attr,
 344                        char *buf)
 345{
 346        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 347        int nr = sensor_attr->index;
 348        struct w83792d_data *data = w83792d_update_device(dev);
 349        return sprintf(buf, "%ld\n",
 350                       IN_FROM_REG(nr, in_count_from_reg(nr, data)));
 351}
 352
 353#define show_in_reg(reg) \
 354static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \
 355                        char *buf) \
 356{ \
 357        struct sensor_device_attribute *sensor_attr \
 358                = to_sensor_dev_attr(attr); \
 359        int nr = sensor_attr->index; \
 360        struct w83792d_data *data = w83792d_update_device(dev); \
 361        return sprintf(buf, "%ld\n", \
 362                       (long)(IN_FROM_REG(nr, data->reg[nr]) * 4)); \
 363}
 364
 365show_in_reg(in_min);
 366show_in_reg(in_max);
 367
 368#define store_in_reg(REG, reg) \
 369static ssize_t store_in_##reg(struct device *dev, \
 370                                struct device_attribute *attr, \
 371                                const char *buf, size_t count) \
 372{ \
 373        struct sensor_device_attribute *sensor_attr \
 374                        = to_sensor_dev_attr(attr); \
 375        int nr = sensor_attr->index; \
 376        struct i2c_client *client = to_i2c_client(dev); \
 377        struct w83792d_data *data = i2c_get_clientdata(client); \
 378        unsigned long val; \
 379        int err = kstrtoul(buf, 10, &val); \
 380        if (err) \
 381                return err; \
 382        mutex_lock(&data->update_lock); \
 383        data->in_##reg[nr] = clamp_val(IN_TO_REG(nr, val) / 4, 0, 255); \
 384        w83792d_write_value(client, W83792D_REG_IN_##REG[nr], \
 385                            data->in_##reg[nr]); \
 386        mutex_unlock(&data->update_lock); \
 387         \
 388        return count; \
 389}
 390store_in_reg(MIN, min);
 391store_in_reg(MAX, max);
 392
 393#define show_fan_reg(reg) \
 394static ssize_t show_##reg(struct device *dev, struct device_attribute *attr, \
 395                        char *buf) \
 396{ \
 397        struct sensor_device_attribute *sensor_attr \
 398                        = to_sensor_dev_attr(attr); \
 399        int nr = sensor_attr->index - 1; \
 400        struct w83792d_data *data = w83792d_update_device(dev); \
 401        return sprintf(buf, "%d\n", \
 402                FAN_FROM_REG(data->reg[nr], DIV_FROM_REG(data->fan_div[nr]))); \
 403}
 404
 405show_fan_reg(fan);
 406show_fan_reg(fan_min);
 407
 408static ssize_t
 409store_fan_min(struct device *dev, struct device_attribute *attr,
 410                const char *buf, size_t count)
 411{
 412        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 413        int nr = sensor_attr->index - 1;
 414        struct i2c_client *client = to_i2c_client(dev);
 415        struct w83792d_data *data = i2c_get_clientdata(client);
 416        unsigned long val;
 417        int err;
 418
 419        err = kstrtoul(buf, 10, &val);
 420        if (err)
 421                return err;
 422
 423        mutex_lock(&data->update_lock);
 424        data->fan_min[nr] = FAN_TO_REG(val, DIV_FROM_REG(data->fan_div[nr]));
 425        w83792d_write_value(client, W83792D_REG_FAN_MIN[nr],
 426                                data->fan_min[nr]);
 427        mutex_unlock(&data->update_lock);
 428
 429        return count;
 430}
 431
 432static ssize_t
 433show_fan_div(struct device *dev, struct device_attribute *attr,
 434                char *buf)
 435{
 436        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 437        int nr = sensor_attr->index;
 438        struct w83792d_data *data = w83792d_update_device(dev);
 439        return sprintf(buf, "%u\n", DIV_FROM_REG(data->fan_div[nr - 1]));
 440}
 441
 442/*
 443 * Note: we save and restore the fan minimum here, because its value is
 444 * determined in part by the fan divisor.  This follows the principle of
 445 * least surprise; the user doesn't expect the fan minimum to change just
 446 * because the divisor changed.
 447 */
 448static ssize_t
 449store_fan_div(struct device *dev, struct device_attribute *attr,
 450                const char *buf, size_t count)
 451{
 452        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 453        int nr = sensor_attr->index - 1;
 454        struct i2c_client *client = to_i2c_client(dev);
 455        struct w83792d_data *data = i2c_get_clientdata(client);
 456        unsigned long min;
 457        /*u8 reg;*/
 458        u8 fan_div_reg = 0;
 459        u8 tmp_fan_div;
 460        unsigned long val;
 461        int err;
 462
 463        err = kstrtoul(buf, 10, &val);
 464        if (err)
 465                return err;
 466
 467        /* Save fan_min */
 468        mutex_lock(&data->update_lock);
 469        min = FAN_FROM_REG(data->fan_min[nr],
 470                           DIV_FROM_REG(data->fan_div[nr]));
 471
 472        data->fan_div[nr] = DIV_TO_REG(val);
 473
 474        fan_div_reg = w83792d_read_value(client, W83792D_REG_FAN_DIV[nr >> 1]);
 475        fan_div_reg &= (nr & 0x01) ? 0x8f : 0xf8;
 476        tmp_fan_div = (nr & 0x01) ? (((data->fan_div[nr]) << 4) & 0x70)
 477                                        : ((data->fan_div[nr]) & 0x07);
 478        w83792d_write_value(client, W83792D_REG_FAN_DIV[nr >> 1],
 479                                        fan_div_reg | tmp_fan_div);
 480
 481        /* Restore fan_min */
 482        data->fan_min[nr] = FAN_TO_REG(min, DIV_FROM_REG(data->fan_div[nr]));
 483        w83792d_write_value(client, W83792D_REG_FAN_MIN[nr], data->fan_min[nr]);
 484        mutex_unlock(&data->update_lock);
 485
 486        return count;
 487}
 488
 489/* read/write the temperature1, includes measured value and limits */
 490
 491static ssize_t show_temp1(struct device *dev, struct device_attribute *attr,
 492                                char *buf)
 493{
 494        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 495        int nr = sensor_attr->index;
 496        struct w83792d_data *data = w83792d_update_device(dev);
 497        return sprintf(buf, "%d\n", TEMP1_FROM_REG(data->temp1[nr]));
 498}
 499
 500static ssize_t store_temp1(struct device *dev, struct device_attribute *attr,
 501                                const char *buf, size_t count)
 502{
 503        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 504        int nr = sensor_attr->index;
 505        struct i2c_client *client = to_i2c_client(dev);
 506        struct w83792d_data *data = i2c_get_clientdata(client);
 507        long val;
 508        int err;
 509
 510        err = kstrtol(buf, 10, &val);
 511        if (err)
 512                return err;
 513
 514        mutex_lock(&data->update_lock);
 515        data->temp1[nr] = TEMP1_TO_REG(val);
 516        w83792d_write_value(client, W83792D_REG_TEMP1[nr],
 517                data->temp1[nr]);
 518        mutex_unlock(&data->update_lock);
 519
 520        return count;
 521}
 522
 523/* read/write the temperature2-3, includes measured value and limits */
 524
 525static ssize_t show_temp23(struct device *dev, struct device_attribute *attr,
 526                                char *buf)
 527{
 528        struct sensor_device_attribute_2 *sensor_attr
 529          = to_sensor_dev_attr_2(attr);
 530        int nr = sensor_attr->nr;
 531        int index = sensor_attr->index;
 532        struct w83792d_data *data = w83792d_update_device(dev);
 533        return sprintf(buf, "%ld\n",
 534                (long)TEMP_ADD_FROM_REG(data->temp_add[nr][index],
 535                        data->temp_add[nr][index+1]));
 536}
 537
 538static ssize_t store_temp23(struct device *dev, struct device_attribute *attr,
 539                                const char *buf, size_t count)
 540{
 541        struct sensor_device_attribute_2 *sensor_attr
 542          = to_sensor_dev_attr_2(attr);
 543        int nr = sensor_attr->nr;
 544        int index = sensor_attr->index;
 545        struct i2c_client *client = to_i2c_client(dev);
 546        struct w83792d_data *data = i2c_get_clientdata(client);
 547        long val;
 548        int err;
 549
 550        err = kstrtol(buf, 10, &val);
 551        if (err)
 552                return err;
 553
 554        mutex_lock(&data->update_lock);
 555        data->temp_add[nr][index] = TEMP_ADD_TO_REG_HIGH(val);
 556        data->temp_add[nr][index+1] = TEMP_ADD_TO_REG_LOW(val);
 557        w83792d_write_value(client, W83792D_REG_TEMP_ADD[nr][index],
 558                data->temp_add[nr][index]);
 559        w83792d_write_value(client, W83792D_REG_TEMP_ADD[nr][index+1],
 560                data->temp_add[nr][index+1]);
 561        mutex_unlock(&data->update_lock);
 562
 563        return count;
 564}
 565
 566/* get realtime status of all sensors items: voltage, temp, fan */
 567static ssize_t
 568alarms_show(struct device *dev, struct device_attribute *attr, char *buf)
 569{
 570        struct w83792d_data *data = w83792d_update_device(dev);
 571        return sprintf(buf, "%d\n", data->alarms);
 572}
 573
 574static ssize_t show_alarm(struct device *dev,
 575                          struct device_attribute *attr, char *buf)
 576{
 577        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 578        int nr = sensor_attr->index;
 579        struct w83792d_data *data = w83792d_update_device(dev);
 580        return sprintf(buf, "%d\n", (data->alarms >> nr) & 1);
 581}
 582
 583static ssize_t
 584show_pwm(struct device *dev, struct device_attribute *attr,
 585                char *buf)
 586{
 587        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 588        int nr = sensor_attr->index;
 589        struct w83792d_data *data = w83792d_update_device(dev);
 590        return sprintf(buf, "%d\n", (data->pwm[nr] & 0x0f) << 4);
 591}
 592
 593static ssize_t
 594show_pwmenable(struct device *dev, struct device_attribute *attr,
 595                        char *buf)
 596{
 597        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 598        int nr = sensor_attr->index - 1;
 599        struct w83792d_data *data = w83792d_update_device(dev);
 600        long pwm_enable_tmp = 1;
 601
 602        switch (data->pwmenable[nr]) {
 603        case 0:
 604                pwm_enable_tmp = 1; /* manual mode */
 605                break;
 606        case 1:
 607                pwm_enable_tmp = 3; /*thermal cruise/Smart Fan I */
 608                break;
 609        case 2:
 610                pwm_enable_tmp = 2; /* Smart Fan II */
 611                break;
 612        }
 613
 614        return sprintf(buf, "%ld\n", pwm_enable_tmp);
 615}
 616
 617static ssize_t
 618store_pwm(struct device *dev, struct device_attribute *attr,
 619                const char *buf, size_t count)
 620{
 621        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 622        int nr = sensor_attr->index;
 623        struct i2c_client *client = to_i2c_client(dev);
 624        struct w83792d_data *data = i2c_get_clientdata(client);
 625        unsigned long val;
 626        int err;
 627
 628        err = kstrtoul(buf, 10, &val);
 629        if (err)
 630                return err;
 631        val = clamp_val(val, 0, 255) >> 4;
 632
 633        mutex_lock(&data->update_lock);
 634        val |= w83792d_read_value(client, W83792D_REG_PWM[nr]) & 0xf0;
 635        data->pwm[nr] = val;
 636        w83792d_write_value(client, W83792D_REG_PWM[nr], data->pwm[nr]);
 637        mutex_unlock(&data->update_lock);
 638
 639        return count;
 640}
 641
 642static ssize_t
 643store_pwmenable(struct device *dev, struct device_attribute *attr,
 644                        const char *buf, size_t count)
 645{
 646        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 647        int nr = sensor_attr->index - 1;
 648        struct i2c_client *client = to_i2c_client(dev);
 649        struct w83792d_data *data = i2c_get_clientdata(client);
 650        u8 fan_cfg_tmp, cfg1_tmp, cfg2_tmp, cfg3_tmp, cfg4_tmp;
 651        unsigned long val;
 652        int err;
 653
 654        err = kstrtoul(buf, 10, &val);
 655        if (err)
 656                return err;
 657
 658        if (val < 1 || val > 3)
 659                return -EINVAL;
 660
 661        mutex_lock(&data->update_lock);
 662        switch (val) {
 663        case 1:
 664                data->pwmenable[nr] = 0; /* manual mode */
 665                break;
 666        case 2:
 667                data->pwmenable[nr] = 2; /* Smart Fan II */
 668                break;
 669        case 3:
 670                data->pwmenable[nr] = 1; /* thermal cruise/Smart Fan I */
 671                break;
 672        }
 673        cfg1_tmp = data->pwmenable[0];
 674        cfg2_tmp = (data->pwmenable[1]) << 2;
 675        cfg3_tmp = (data->pwmenable[2]) << 4;
 676        cfg4_tmp = w83792d_read_value(client, W83792D_REG_FAN_CFG) & 0xc0;
 677        fan_cfg_tmp = ((cfg4_tmp | cfg3_tmp) | cfg2_tmp) | cfg1_tmp;
 678        w83792d_write_value(client, W83792D_REG_FAN_CFG, fan_cfg_tmp);
 679        mutex_unlock(&data->update_lock);
 680
 681        return count;
 682}
 683
 684static ssize_t
 685show_pwm_mode(struct device *dev, struct device_attribute *attr,
 686                        char *buf)
 687{
 688        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 689        int nr = sensor_attr->index;
 690        struct w83792d_data *data = w83792d_update_device(dev);
 691        return sprintf(buf, "%d\n", data->pwm[nr] >> 7);
 692}
 693
 694static ssize_t
 695store_pwm_mode(struct device *dev, struct device_attribute *attr,
 696                        const char *buf, size_t count)
 697{
 698        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 699        int nr = sensor_attr->index;
 700        struct i2c_client *client = to_i2c_client(dev);
 701        struct w83792d_data *data = i2c_get_clientdata(client);
 702        unsigned long val;
 703        int err;
 704
 705        err = kstrtoul(buf, 10, &val);
 706        if (err)
 707                return err;
 708        if (val > 1)
 709                return -EINVAL;
 710
 711        mutex_lock(&data->update_lock);
 712        data->pwm[nr] = w83792d_read_value(client, W83792D_REG_PWM[nr]);
 713        if (val) {                      /* PWM mode */
 714                data->pwm[nr] |= 0x80;
 715        } else {                        /* DC mode */
 716                data->pwm[nr] &= 0x7f;
 717        }
 718        w83792d_write_value(client, W83792D_REG_PWM[nr], data->pwm[nr]);
 719        mutex_unlock(&data->update_lock);
 720
 721        return count;
 722}
 723
 724static ssize_t
 725intrusion0_alarm_show(struct device *dev, struct device_attribute *attr,
 726                      char *buf)
 727{
 728        struct w83792d_data *data = w83792d_update_device(dev);
 729        return sprintf(buf, "%d\n", data->chassis);
 730}
 731
 732static ssize_t
 733intrusion0_alarm_store(struct device *dev, struct device_attribute *attr,
 734                       const char *buf, size_t count)
 735{
 736        struct i2c_client *client = to_i2c_client(dev);
 737        struct w83792d_data *data = i2c_get_clientdata(client);
 738        unsigned long val;
 739        u8 reg;
 740
 741        if (kstrtoul(buf, 10, &val) || val != 0)
 742                return -EINVAL;
 743
 744        mutex_lock(&data->update_lock);
 745        reg = w83792d_read_value(client, W83792D_REG_CHASSIS_CLR);
 746        w83792d_write_value(client, W83792D_REG_CHASSIS_CLR, reg | 0x80);
 747        data->valid = 0;                /* Force cache refresh */
 748        mutex_unlock(&data->update_lock);
 749
 750        return count;
 751}
 752
 753/* For Smart Fan I / Thermal Cruise */
 754static ssize_t
 755show_thermal_cruise(struct device *dev, struct device_attribute *attr,
 756                        char *buf)
 757{
 758        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 759        int nr = sensor_attr->index;
 760        struct w83792d_data *data = w83792d_update_device(dev);
 761        return sprintf(buf, "%ld\n", (long)data->thermal_cruise[nr-1]);
 762}
 763
 764static ssize_t
 765store_thermal_cruise(struct device *dev, struct device_attribute *attr,
 766                        const char *buf, size_t count)
 767{
 768        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 769        int nr = sensor_attr->index - 1;
 770        struct i2c_client *client = to_i2c_client(dev);
 771        struct w83792d_data *data = i2c_get_clientdata(client);
 772        u8 target_tmp = 0, target_mask = 0;
 773        unsigned long val;
 774        int err;
 775
 776        err = kstrtoul(buf, 10, &val);
 777        if (err)
 778                return err;
 779
 780        target_tmp = val;
 781        target_tmp = target_tmp & 0x7f;
 782        mutex_lock(&data->update_lock);
 783        target_mask = w83792d_read_value(client,
 784                                         W83792D_REG_THERMAL[nr]) & 0x80;
 785        data->thermal_cruise[nr] = clamp_val(target_tmp, 0, 255);
 786        w83792d_write_value(client, W83792D_REG_THERMAL[nr],
 787                (data->thermal_cruise[nr]) | target_mask);
 788        mutex_unlock(&data->update_lock);
 789
 790        return count;
 791}
 792
 793/* For Smart Fan I/Thermal Cruise and Smart Fan II */
 794static ssize_t
 795show_tolerance(struct device *dev, struct device_attribute *attr,
 796                char *buf)
 797{
 798        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 799        int nr = sensor_attr->index;
 800        struct w83792d_data *data = w83792d_update_device(dev);
 801        return sprintf(buf, "%ld\n", (long)data->tolerance[nr-1]);
 802}
 803
 804static ssize_t
 805store_tolerance(struct device *dev, struct device_attribute *attr,
 806                const char *buf, size_t count)
 807{
 808        struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
 809        int nr = sensor_attr->index - 1;
 810        struct i2c_client *client = to_i2c_client(dev);
 811        struct w83792d_data *data = i2c_get_clientdata(client);
 812        u8 tol_tmp, tol_mask;
 813        unsigned long val;
 814        int err;
 815
 816        err = kstrtoul(buf, 10, &val);
 817        if (err)
 818                return err;
 819
 820        mutex_lock(&data->update_lock);
 821        tol_mask = w83792d_read_value(client,
 822                W83792D_REG_TOLERANCE[nr]) & ((nr == 1) ? 0x0f : 0xf0);
 823        tol_tmp = clamp_val(val, 0, 15);
 824        tol_tmp &= 0x0f;
 825        data->tolerance[nr] = tol_tmp;
 826        if (nr == 1)
 827                tol_tmp <<= 4;
 828        w83792d_write_value(client, W83792D_REG_TOLERANCE[nr],
 829                tol_mask | tol_tmp);
 830        mutex_unlock(&data->update_lock);
 831
 832        return count;
 833}
 834
 835/* For Smart Fan II */
 836static ssize_t
 837show_sf2_point(struct device *dev, struct device_attribute *attr,
 838                char *buf)
 839{
 840        struct sensor_device_attribute_2 *sensor_attr
 841          = to_sensor_dev_attr_2(attr);
 842        int nr = sensor_attr->nr;
 843        int index = sensor_attr->index;
 844        struct w83792d_data *data = w83792d_update_device(dev);
 845        return sprintf(buf, "%ld\n", (long)data->sf2_points[index-1][nr-1]);
 846}
 847
 848static ssize_t
 849store_sf2_point(struct device *dev, struct device_attribute *attr,
 850                const char *buf, size_t count)
 851{
 852        struct sensor_device_attribute_2 *sensor_attr
 853          = to_sensor_dev_attr_2(attr);
 854        int nr = sensor_attr->nr - 1;
 855        int index = sensor_attr->index - 1;
 856        struct i2c_client *client = to_i2c_client(dev);
 857        struct w83792d_data *data = i2c_get_clientdata(client);
 858        u8 mask_tmp = 0;
 859        unsigned long val;
 860        int err;
 861
 862        err = kstrtoul(buf, 10, &val);
 863        if (err)
 864                return err;
 865
 866        mutex_lock(&data->update_lock);
 867        data->sf2_points[index][nr] = clamp_val(val, 0, 127);
 868        mask_tmp = w83792d_read_value(client,
 869                                        W83792D_REG_POINTS[index][nr]) & 0x80;
 870        w83792d_write_value(client, W83792D_REG_POINTS[index][nr],
 871                mask_tmp|data->sf2_points[index][nr]);
 872        mutex_unlock(&data->update_lock);
 873
 874        return count;
 875}
 876
 877static ssize_t
 878show_sf2_level(struct device *dev, struct device_attribute *attr,
 879                char *buf)
 880{
 881        struct sensor_device_attribute_2 *sensor_attr
 882          = to_sensor_dev_attr_2(attr);
 883        int nr = sensor_attr->nr;
 884        int index = sensor_attr->index;
 885        struct w83792d_data *data = w83792d_update_device(dev);
 886        return sprintf(buf, "%d\n",
 887                        (((data->sf2_levels[index-1][nr]) * 100) / 15));
 888}
 889
 890static ssize_t
 891store_sf2_level(struct device *dev, struct device_attribute *attr,
 892                const char *buf, size_t count)
 893{
 894        struct sensor_device_attribute_2 *sensor_attr
 895          = to_sensor_dev_attr_2(attr);
 896        int nr = sensor_attr->nr;
 897        int index = sensor_attr->index - 1;
 898        struct i2c_client *client = to_i2c_client(dev);
 899        struct w83792d_data *data = i2c_get_clientdata(client);
 900        u8 mask_tmp = 0, level_tmp = 0;
 901        unsigned long val;
 902        int err;
 903
 904        err = kstrtoul(buf, 10, &val);
 905        if (err)
 906                return err;
 907
 908        mutex_lock(&data->update_lock);
 909        data->sf2_levels[index][nr] = clamp_val((val * 15) / 100, 0, 15);
 910        mask_tmp = w83792d_read_value(client, W83792D_REG_LEVELS[index][nr])
 911                & ((nr == 3) ? 0xf0 : 0x0f);
 912        if (nr == 3)
 913                level_tmp = data->sf2_levels[index][nr];
 914        else
 915                level_tmp = data->sf2_levels[index][nr] << 4;
 916        w83792d_write_value(client, W83792D_REG_LEVELS[index][nr],
 917                            level_tmp | mask_tmp);
 918        mutex_unlock(&data->update_lock);
 919
 920        return count;
 921}
 922
 923
 924static int
 925w83792d_detect_subclients(struct i2c_client *new_client)
 926{
 927        int i, id;
 928        int address = new_client->addr;
 929        u8 val;
 930        struct i2c_adapter *adapter = new_client->adapter;
 931        struct w83792d_data *data = i2c_get_clientdata(new_client);
 932
 933        id = i2c_adapter_id(adapter);
 934        if (force_subclients[0] == id && force_subclients[1] == address) {
 935                for (i = 2; i <= 3; i++) {
 936                        if (force_subclients[i] < 0x48 ||
 937                            force_subclients[i] > 0x4f) {
 938                                dev_err(&new_client->dev,
 939                                        "invalid subclient address %d; must be 0x48-0x4f\n",
 940                                        force_subclients[i]);
 941                                return -ENODEV;
 942                        }
 943                }
 944                w83792d_write_value(new_client, W83792D_REG_I2C_SUBADDR,
 945                                        (force_subclients[2] & 0x07) |
 946                                        ((force_subclients[3] & 0x07) << 4));
 947        }
 948
 949        val = w83792d_read_value(new_client, W83792D_REG_I2C_SUBADDR);
 950        if (!(val & 0x08))
 951                data->lm75[0] = devm_i2c_new_dummy_device(&new_client->dev, adapter,
 952                                                          0x48 + (val & 0x7));
 953        if (!(val & 0x80)) {
 954                if (!IS_ERR(data->lm75[0]) &&
 955                        ((val & 0x7) == ((val >> 4) & 0x7))) {
 956                        dev_err(&new_client->dev,
 957                                "duplicate addresses 0x%x, use force_subclient\n",
 958                                data->lm75[0]->addr);
 959                        return -ENODEV;
 960                }
 961                data->lm75[1] = devm_i2c_new_dummy_device(&new_client->dev, adapter,
 962                                                          0x48 + ((val >> 4) & 0x7));
 963        }
 964
 965        return 0;
 966}
 967
 968static SENSOR_DEVICE_ATTR(in0_input, S_IRUGO, show_in, NULL, 0);
 969static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, show_in, NULL, 1);
 970static SENSOR_DEVICE_ATTR(in2_input, S_IRUGO, show_in, NULL, 2);
 971static SENSOR_DEVICE_ATTR(in3_input, S_IRUGO, show_in, NULL, 3);
 972static SENSOR_DEVICE_ATTR(in4_input, S_IRUGO, show_in, NULL, 4);
 973static SENSOR_DEVICE_ATTR(in5_input, S_IRUGO, show_in, NULL, 5);
 974static SENSOR_DEVICE_ATTR(in6_input, S_IRUGO, show_in, NULL, 6);
 975static SENSOR_DEVICE_ATTR(in7_input, S_IRUGO, show_in, NULL, 7);
 976static SENSOR_DEVICE_ATTR(in8_input, S_IRUGO, show_in, NULL, 8);
 977static SENSOR_DEVICE_ATTR(in0_min, S_IWUSR | S_IRUGO,
 978                        show_in_min, store_in_min, 0);
 979static SENSOR_DEVICE_ATTR(in1_min, S_IWUSR | S_IRUGO,
 980                        show_in_min, store_in_min, 1);
 981static SENSOR_DEVICE_ATTR(in2_min, S_IWUSR | S_IRUGO,
 982                        show_in_min, store_in_min, 2);
 983static SENSOR_DEVICE_ATTR(in3_min, S_IWUSR | S_IRUGO,
 984                        show_in_min, store_in_min, 3);
 985static SENSOR_DEVICE_ATTR(in4_min, S_IWUSR | S_IRUGO,
 986                        show_in_min, store_in_min, 4);
 987static SENSOR_DEVICE_ATTR(in5_min, S_IWUSR | S_IRUGO,
 988                        show_in_min, store_in_min, 5);
 989static SENSOR_DEVICE_ATTR(in6_min, S_IWUSR | S_IRUGO,
 990                        show_in_min, store_in_min, 6);
 991static SENSOR_DEVICE_ATTR(in7_min, S_IWUSR | S_IRUGO,
 992                        show_in_min, store_in_min, 7);
 993static SENSOR_DEVICE_ATTR(in8_min, S_IWUSR | S_IRUGO,
 994                        show_in_min, store_in_min, 8);
 995static SENSOR_DEVICE_ATTR(in0_max, S_IWUSR | S_IRUGO,
 996                        show_in_max, store_in_max, 0);
 997static SENSOR_DEVICE_ATTR(in1_max, S_IWUSR | S_IRUGO,
 998                        show_in_max, store_in_max, 1);
 999static SENSOR_DEVICE_ATTR(in2_max, S_IWUSR | S_IRUGO,
1000                        show_in_max, store_in_max, 2);
1001static SENSOR_DEVICE_ATTR(in3_max, S_IWUSR | S_IRUGO,
1002                        show_in_max, store_in_max, 3);
1003static SENSOR_DEVICE_ATTR(in4_max, S_IWUSR | S_IRUGO,
1004                        show_in_max, store_in_max, 4);
1005static SENSOR_DEVICE_ATTR(in5_max, S_IWUSR | S_IRUGO,
1006                        show_in_max, store_in_max, 5);
1007static SENSOR_DEVICE_ATTR(in6_max, S_IWUSR | S_IRUGO,
1008                        show_in_max, store_in_max, 6);
1009static SENSOR_DEVICE_ATTR(in7_max, S_IWUSR | S_IRUGO,
1010                        show_in_max, store_in_max, 7);
1011static SENSOR_DEVICE_ATTR(in8_max, S_IWUSR | S_IRUGO,
1012                        show_in_max, store_in_max, 8);
1013static SENSOR_DEVICE_ATTR_2(temp1_input, S_IRUGO, show_temp1, NULL, 0, 0);
1014static SENSOR_DEVICE_ATTR_2(temp2_input, S_IRUGO, show_temp23, NULL, 0, 0);
1015static SENSOR_DEVICE_ATTR_2(temp3_input, S_IRUGO, show_temp23, NULL, 1, 0);
1016static SENSOR_DEVICE_ATTR_2(temp1_max, S_IRUGO | S_IWUSR,
1017                        show_temp1, store_temp1, 0, 1);
1018static SENSOR_DEVICE_ATTR_2(temp2_max, S_IRUGO | S_IWUSR, show_temp23,
1019                        store_temp23, 0, 2);
1020static SENSOR_DEVICE_ATTR_2(temp3_max, S_IRUGO | S_IWUSR, show_temp23,
1021                        store_temp23, 1, 2);
1022static SENSOR_DEVICE_ATTR_2(temp1_max_hyst, S_IRUGO | S_IWUSR,
1023                        show_temp1, store_temp1, 0, 2);
1024static SENSOR_DEVICE_ATTR_2(temp2_max_hyst, S_IRUGO | S_IWUSR,
1025                        show_temp23, store_temp23, 0, 4);
1026static SENSOR_DEVICE_ATTR_2(temp3_max_hyst, S_IRUGO | S_IWUSR,
1027                        show_temp23, store_temp23, 1, 4);
1028static DEVICE_ATTR_RO(alarms);
1029static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, 0);
1030static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, 1);
1031static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, 2);
1032static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, 3);
1033static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, 4);
1034static SENSOR_DEVICE_ATTR(fan1_alarm, S_IRUGO, show_alarm, NULL, 5);
1035static SENSOR_DEVICE_ATTR(fan2_alarm, S_IRUGO, show_alarm, NULL, 6);
1036static SENSOR_DEVICE_ATTR(fan3_alarm, S_IRUGO, show_alarm, NULL, 7);
1037static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, 8);
1038static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, 9);
1039static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, 10);
1040static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, show_alarm, NULL, 11);
1041static SENSOR_DEVICE_ATTR(in6_alarm, S_IRUGO, show_alarm, NULL, 12);
1042static SENSOR_DEVICE_ATTR(fan7_alarm, S_IRUGO, show_alarm, NULL, 15);
1043static SENSOR_DEVICE_ATTR(in7_alarm, S_IRUGO, show_alarm, NULL, 19);
1044static SENSOR_DEVICE_ATTR(in8_alarm, S_IRUGO, show_alarm, NULL, 20);
1045static SENSOR_DEVICE_ATTR(fan4_alarm, S_IRUGO, show_alarm, NULL, 21);
1046static SENSOR_DEVICE_ATTR(fan5_alarm, S_IRUGO, show_alarm, NULL, 22);
1047static SENSOR_DEVICE_ATTR(fan6_alarm, S_IRUGO, show_alarm, NULL, 23);
1048static DEVICE_ATTR_RW(intrusion0_alarm);
1049static SENSOR_DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 0);
1050static SENSOR_DEVICE_ATTR(pwm2, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 1);
1051static SENSOR_DEVICE_ATTR(pwm3, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 2);
1052static SENSOR_DEVICE_ATTR(pwm4, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 3);
1053static SENSOR_DEVICE_ATTR(pwm5, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 4);
1054static SENSOR_DEVICE_ATTR(pwm6, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 5);
1055static SENSOR_DEVICE_ATTR(pwm7, S_IWUSR | S_IRUGO, show_pwm, store_pwm, 6);
1056static SENSOR_DEVICE_ATTR(pwm1_enable, S_IWUSR | S_IRUGO,
1057                        show_pwmenable, store_pwmenable, 1);
1058static SENSOR_DEVICE_ATTR(pwm2_enable, S_IWUSR | S_IRUGO,
1059                        show_pwmenable, store_pwmenable, 2);
1060static SENSOR_DEVICE_ATTR(pwm3_enable, S_IWUSR | S_IRUGO,
1061                        show_pwmenable, store_pwmenable, 3);
1062static SENSOR_DEVICE_ATTR(pwm1_mode, S_IWUSR | S_IRUGO,
1063                        show_pwm_mode, store_pwm_mode, 0);
1064static SENSOR_DEVICE_ATTR(pwm2_mode, S_IWUSR | S_IRUGO,
1065                        show_pwm_mode, store_pwm_mode, 1);
1066static SENSOR_DEVICE_ATTR(pwm3_mode, S_IWUSR | S_IRUGO,
1067                        show_pwm_mode, store_pwm_mode, 2);
1068static SENSOR_DEVICE_ATTR(pwm4_mode, S_IWUSR | S_IRUGO,
1069                        show_pwm_mode, store_pwm_mode, 3);
1070static SENSOR_DEVICE_ATTR(pwm5_mode, S_IWUSR | S_IRUGO,
1071                        show_pwm_mode, store_pwm_mode, 4);
1072static SENSOR_DEVICE_ATTR(pwm6_mode, S_IWUSR | S_IRUGO,
1073                        show_pwm_mode, store_pwm_mode, 5);
1074static SENSOR_DEVICE_ATTR(pwm7_mode, S_IWUSR | S_IRUGO,
1075                        show_pwm_mode, store_pwm_mode, 6);
1076static SENSOR_DEVICE_ATTR(tolerance1, S_IWUSR | S_IRUGO,
1077                        show_tolerance, store_tolerance, 1);
1078static SENSOR_DEVICE_ATTR(tolerance2, S_IWUSR | S_IRUGO,
1079                        show_tolerance, store_tolerance, 2);
1080static SENSOR_DEVICE_ATTR(tolerance3, S_IWUSR | S_IRUGO,
1081                        show_tolerance, store_tolerance, 3);
1082static SENSOR_DEVICE_ATTR(thermal_cruise1, S_IWUSR | S_IRUGO,
1083                        show_thermal_cruise, store_thermal_cruise, 1);
1084static SENSOR_DEVICE_ATTR(thermal_cruise2, S_IWUSR | S_IRUGO,
1085                        show_thermal_cruise, store_thermal_cruise, 2);
1086static SENSOR_DEVICE_ATTR(thermal_cruise3, S_IWUSR | S_IRUGO,
1087                        show_thermal_cruise, store_thermal_cruise, 3);
1088static SENSOR_DEVICE_ATTR_2(sf2_point1_fan1, S_IRUGO | S_IWUSR,
1089                        show_sf2_point, store_sf2_point, 1, 1);
1090static SENSOR_DEVICE_ATTR_2(sf2_point2_fan1, S_IRUGO | S_IWUSR,
1091                        show_sf2_point, store_sf2_point, 2, 1);
1092static SENSOR_DEVICE_ATTR_2(sf2_point3_fan1, S_IRUGO | S_IWUSR,
1093                        show_sf2_point, store_sf2_point, 3, 1);
1094static SENSOR_DEVICE_ATTR_2(sf2_point4_fan1, S_IRUGO | S_IWUSR,
1095                        show_sf2_point, store_sf2_point, 4, 1);
1096static SENSOR_DEVICE_ATTR_2(sf2_point1_fan2, S_IRUGO | S_IWUSR,
1097                        show_sf2_point, store_sf2_point, 1, 2);
1098static SENSOR_DEVICE_ATTR_2(sf2_point2_fan2, S_IRUGO | S_IWUSR,
1099                        show_sf2_point, store_sf2_point, 2, 2);
1100static SENSOR_DEVICE_ATTR_2(sf2_point3_fan2, S_IRUGO | S_IWUSR,
1101                        show_sf2_point, store_sf2_point, 3, 2);
1102static SENSOR_DEVICE_ATTR_2(sf2_point4_fan2, S_IRUGO | S_IWUSR,
1103                        show_sf2_point, store_sf2_point, 4, 2);
1104static SENSOR_DEVICE_ATTR_2(sf2_point1_fan3, S_IRUGO | S_IWUSR,
1105                        show_sf2_point, store_sf2_point, 1, 3);
1106static SENSOR_DEVICE_ATTR_2(sf2_point2_fan3, S_IRUGO | S_IWUSR,
1107                        show_sf2_point, store_sf2_point, 2, 3);
1108static SENSOR_DEVICE_ATTR_2(sf2_point3_fan3, S_IRUGO | S_IWUSR,
1109                        show_sf2_point, store_sf2_point, 3, 3);
1110static SENSOR_DEVICE_ATTR_2(sf2_point4_fan3, S_IRUGO | S_IWUSR,
1111                        show_sf2_point, store_sf2_point, 4, 3);
1112static SENSOR_DEVICE_ATTR_2(sf2_level1_fan1, S_IRUGO | S_IWUSR,
1113                        show_sf2_level, store_sf2_level, 1, 1);
1114static SENSOR_DEVICE_ATTR_2(sf2_level2_fan1, S_IRUGO | S_IWUSR,
1115                        show_sf2_level, store_sf2_level, 2, 1);
1116static SENSOR_DEVICE_ATTR_2(sf2_level3_fan1, S_IRUGO | S_IWUSR,
1117                        show_sf2_level, store_sf2_level, 3, 1);
1118static SENSOR_DEVICE_ATTR_2(sf2_level1_fan2, S_IRUGO | S_IWUSR,
1119                        show_sf2_level, store_sf2_level, 1, 2);
1120static SENSOR_DEVICE_ATTR_2(sf2_level2_fan2, S_IRUGO | S_IWUSR,
1121                        show_sf2_level, store_sf2_level, 2, 2);
1122static SENSOR_DEVICE_ATTR_2(sf2_level3_fan2, S_IRUGO | S_IWUSR,
1123                        show_sf2_level, store_sf2_level, 3, 2);
1124static SENSOR_DEVICE_ATTR_2(sf2_level1_fan3, S_IRUGO | S_IWUSR,
1125                        show_sf2_level, store_sf2_level, 1, 3);
1126static SENSOR_DEVICE_ATTR_2(sf2_level2_fan3, S_IRUGO | S_IWUSR,
1127                        show_sf2_level, store_sf2_level, 2, 3);
1128static SENSOR_DEVICE_ATTR_2(sf2_level3_fan3, S_IRUGO | S_IWUSR,
1129                        show_sf2_level, store_sf2_level, 3, 3);
1130static SENSOR_DEVICE_ATTR(fan1_input, S_IRUGO, show_fan, NULL, 1);
1131static SENSOR_DEVICE_ATTR(fan2_input, S_IRUGO, show_fan, NULL, 2);
1132static SENSOR_DEVICE_ATTR(fan3_input, S_IRUGO, show_fan, NULL, 3);
1133static SENSOR_DEVICE_ATTR(fan4_input, S_IRUGO, show_fan, NULL, 4);
1134static SENSOR_DEVICE_ATTR(fan5_input, S_IRUGO, show_fan, NULL, 5);
1135static SENSOR_DEVICE_ATTR(fan6_input, S_IRUGO, show_fan, NULL, 6);
1136static SENSOR_DEVICE_ATTR(fan7_input, S_IRUGO, show_fan, NULL, 7);
1137static SENSOR_DEVICE_ATTR(fan1_min, S_IWUSR | S_IRUGO,
1138                        show_fan_min, store_fan_min, 1);
1139static SENSOR_DEVICE_ATTR(fan2_min, S_IWUSR | S_IRUGO,
1140                        show_fan_min, store_fan_min, 2);
1141static SENSOR_DEVICE_ATTR(fan3_min, S_IWUSR | S_IRUGO,
1142                        show_fan_min, store_fan_min, 3);
1143static SENSOR_DEVICE_ATTR(fan4_min, S_IWUSR | S_IRUGO,
1144                        show_fan_min, store_fan_min, 4);
1145static SENSOR_DEVICE_ATTR(fan5_min, S_IWUSR | S_IRUGO,
1146                        show_fan_min, store_fan_min, 5);
1147static SENSOR_DEVICE_ATTR(fan6_min, S_IWUSR | S_IRUGO,
1148                        show_fan_min, store_fan_min, 6);
1149static SENSOR_DEVICE_ATTR(fan7_min, S_IWUSR | S_IRUGO,
1150                        show_fan_min, store_fan_min, 7);
1151static SENSOR_DEVICE_ATTR(fan1_div, S_IWUSR | S_IRUGO,
1152                        show_fan_div, store_fan_div, 1);
1153static SENSOR_DEVICE_ATTR(fan2_div, S_IWUSR | S_IRUGO,
1154                        show_fan_div, store_fan_div, 2);
1155static SENSOR_DEVICE_ATTR(fan3_div, S_IWUSR | S_IRUGO,
1156                        show_fan_div, store_fan_div, 3);
1157static SENSOR_DEVICE_ATTR(fan4_div, S_IWUSR | S_IRUGO,
1158                        show_fan_div, store_fan_div, 4);
1159static SENSOR_DEVICE_ATTR(fan5_div, S_IWUSR | S_IRUGO,
1160                        show_fan_div, store_fan_div, 5);
1161static SENSOR_DEVICE_ATTR(fan6_div, S_IWUSR | S_IRUGO,
1162                        show_fan_div, store_fan_div, 6);
1163static SENSOR_DEVICE_ATTR(fan7_div, S_IWUSR | S_IRUGO,
1164                        show_fan_div, store_fan_div, 7);
1165
1166static struct attribute *w83792d_attributes_fan[4][7] = {
1167        {
1168                &sensor_dev_attr_fan4_input.dev_attr.attr,
1169                &sensor_dev_attr_fan4_min.dev_attr.attr,
1170                &sensor_dev_attr_fan4_div.dev_attr.attr,
1171                &sensor_dev_attr_fan4_alarm.dev_attr.attr,
1172                &sensor_dev_attr_pwm4.dev_attr.attr,
1173                &sensor_dev_attr_pwm4_mode.dev_attr.attr,
1174                NULL
1175        }, {
1176                &sensor_dev_attr_fan5_input.dev_attr.attr,
1177                &sensor_dev_attr_fan5_min.dev_attr.attr,
1178                &sensor_dev_attr_fan5_div.dev_attr.attr,
1179                &sensor_dev_attr_fan5_alarm.dev_attr.attr,
1180                &sensor_dev_attr_pwm5.dev_attr.attr,
1181                &sensor_dev_attr_pwm5_mode.dev_attr.attr,
1182                NULL
1183        }, {
1184                &sensor_dev_attr_fan6_input.dev_attr.attr,
1185                &sensor_dev_attr_fan6_min.dev_attr.attr,
1186                &sensor_dev_attr_fan6_div.dev_attr.attr,
1187                &sensor_dev_attr_fan6_alarm.dev_attr.attr,
1188                &sensor_dev_attr_pwm6.dev_attr.attr,
1189                &sensor_dev_attr_pwm6_mode.dev_attr.attr,
1190                NULL
1191        }, {
1192                &sensor_dev_attr_fan7_input.dev_attr.attr,
1193                &sensor_dev_attr_fan7_min.dev_attr.attr,
1194                &sensor_dev_attr_fan7_div.dev_attr.attr,
1195                &sensor_dev_attr_fan7_alarm.dev_attr.attr,
1196                &sensor_dev_attr_pwm7.dev_attr.attr,
1197                &sensor_dev_attr_pwm7_mode.dev_attr.attr,
1198                NULL
1199        }
1200};
1201
1202static const struct attribute_group w83792d_group_fan[4] = {
1203        { .attrs = w83792d_attributes_fan[0] },
1204        { .attrs = w83792d_attributes_fan[1] },
1205        { .attrs = w83792d_attributes_fan[2] },
1206        { .attrs = w83792d_attributes_fan[3] },
1207};
1208
1209static struct attribute *w83792d_attributes[] = {
1210        &sensor_dev_attr_in0_input.dev_attr.attr,
1211        &sensor_dev_attr_in0_max.dev_attr.attr,
1212        &sensor_dev_attr_in0_min.dev_attr.attr,
1213        &sensor_dev_attr_in1_input.dev_attr.attr,
1214        &sensor_dev_attr_in1_max.dev_attr.attr,
1215        &sensor_dev_attr_in1_min.dev_attr.attr,
1216        &sensor_dev_attr_in2_input.dev_attr.attr,
1217        &sensor_dev_attr_in2_max.dev_attr.attr,
1218        &sensor_dev_attr_in2_min.dev_attr.attr,
1219        &sensor_dev_attr_in3_input.dev_attr.attr,
1220        &sensor_dev_attr_in3_max.dev_attr.attr,
1221        &sensor_dev_attr_in3_min.dev_attr.attr,
1222        &sensor_dev_attr_in4_input.dev_attr.attr,
1223        &sensor_dev_attr_in4_max.dev_attr.attr,
1224        &sensor_dev_attr_in4_min.dev_attr.attr,
1225        &sensor_dev_attr_in5_input.dev_attr.attr,
1226        &sensor_dev_attr_in5_max.dev_attr.attr,
1227        &sensor_dev_attr_in5_min.dev_attr.attr,
1228        &sensor_dev_attr_in6_input.dev_attr.attr,
1229        &sensor_dev_attr_in6_max.dev_attr.attr,
1230        &sensor_dev_attr_in6_min.dev_attr.attr,
1231        &sensor_dev_attr_in7_input.dev_attr.attr,
1232        &sensor_dev_attr_in7_max.dev_attr.attr,
1233        &sensor_dev_attr_in7_min.dev_attr.attr,
1234        &sensor_dev_attr_in8_input.dev_attr.attr,
1235        &sensor_dev_attr_in8_max.dev_attr.attr,
1236        &sensor_dev_attr_in8_min.dev_attr.attr,
1237        &sensor_dev_attr_in0_alarm.dev_attr.attr,
1238        &sensor_dev_attr_in1_alarm.dev_attr.attr,
1239        &sensor_dev_attr_in2_alarm.dev_attr.attr,
1240        &sensor_dev_attr_in3_alarm.dev_attr.attr,
1241        &sensor_dev_attr_in4_alarm.dev_attr.attr,
1242        &sensor_dev_attr_in5_alarm.dev_attr.attr,
1243        &sensor_dev_attr_in6_alarm.dev_attr.attr,
1244        &sensor_dev_attr_in7_alarm.dev_attr.attr,
1245        &sensor_dev_attr_in8_alarm.dev_attr.attr,
1246        &sensor_dev_attr_temp1_input.dev_attr.attr,
1247        &sensor_dev_attr_temp1_max.dev_attr.attr,
1248        &sensor_dev_attr_temp1_max_hyst.dev_attr.attr,
1249        &sensor_dev_attr_temp2_input.dev_attr.attr,
1250        &sensor_dev_attr_temp2_max.dev_attr.attr,
1251        &sensor_dev_attr_temp2_max_hyst.dev_attr.attr,
1252        &sensor_dev_attr_temp3_input.dev_attr.attr,
1253        &sensor_dev_attr_temp3_max.dev_attr.attr,
1254        &sensor_dev_attr_temp3_max_hyst.dev_attr.attr,
1255        &sensor_dev_attr_temp1_alarm.dev_attr.attr,
1256        &sensor_dev_attr_temp2_alarm.dev_attr.attr,
1257        &sensor_dev_attr_temp3_alarm.dev_attr.attr,
1258        &sensor_dev_attr_pwm1.dev_attr.attr,
1259        &sensor_dev_attr_pwm1_mode.dev_attr.attr,
1260        &sensor_dev_attr_pwm1_enable.dev_attr.attr,
1261        &sensor_dev_attr_pwm2.dev_attr.attr,
1262        &sensor_dev_attr_pwm2_mode.dev_attr.attr,
1263        &sensor_dev_attr_pwm2_enable.dev_attr.attr,
1264        &sensor_dev_attr_pwm3.dev_attr.attr,
1265        &sensor_dev_attr_pwm3_mode.dev_attr.attr,
1266        &sensor_dev_attr_pwm3_enable.dev_attr.attr,
1267        &dev_attr_alarms.attr,
1268        &dev_attr_intrusion0_alarm.attr,
1269        &sensor_dev_attr_tolerance1.dev_attr.attr,
1270        &sensor_dev_attr_thermal_cruise1.dev_attr.attr,
1271        &sensor_dev_attr_tolerance2.dev_attr.attr,
1272        &sensor_dev_attr_thermal_cruise2.dev_attr.attr,
1273        &sensor_dev_attr_tolerance3.dev_attr.attr,
1274        &sensor_dev_attr_thermal_cruise3.dev_attr.attr,
1275        &sensor_dev_attr_sf2_point1_fan1.dev_attr.attr,
1276        &sensor_dev_attr_sf2_point2_fan1.dev_attr.attr,
1277        &sensor_dev_attr_sf2_point3_fan1.dev_attr.attr,
1278        &sensor_dev_attr_sf2_point4_fan1.dev_attr.attr,
1279        &sensor_dev_attr_sf2_point1_fan2.dev_attr.attr,
1280        &sensor_dev_attr_sf2_point2_fan2.dev_attr.attr,
1281        &sensor_dev_attr_sf2_point3_fan2.dev_attr.attr,
1282        &sensor_dev_attr_sf2_point4_fan2.dev_attr.attr,
1283        &sensor_dev_attr_sf2_point1_fan3.dev_attr.attr,
1284        &sensor_dev_attr_sf2_point2_fan3.dev_attr.attr,
1285        &sensor_dev_attr_sf2_point3_fan3.dev_attr.attr,
1286        &sensor_dev_attr_sf2_point4_fan3.dev_attr.attr,
1287        &sensor_dev_attr_sf2_level1_fan1.dev_attr.attr,
1288        &sensor_dev_attr_sf2_level2_fan1.dev_attr.attr,
1289        &sensor_dev_attr_sf2_level3_fan1.dev_attr.attr,
1290        &sensor_dev_attr_sf2_level1_fan2.dev_attr.attr,
1291        &sensor_dev_attr_sf2_level2_fan2.dev_attr.attr,
1292        &sensor_dev_attr_sf2_level3_fan2.dev_attr.attr,
1293        &sensor_dev_attr_sf2_level1_fan3.dev_attr.attr,
1294        &sensor_dev_attr_sf2_level2_fan3.dev_attr.attr,
1295        &sensor_dev_attr_sf2_level3_fan3.dev_attr.attr,
1296        &sensor_dev_attr_fan1_input.dev_attr.attr,
1297        &sensor_dev_attr_fan1_min.dev_attr.attr,
1298        &sensor_dev_attr_fan1_div.dev_attr.attr,
1299        &sensor_dev_attr_fan1_alarm.dev_attr.attr,
1300        &sensor_dev_attr_fan2_input.dev_attr.attr,
1301        &sensor_dev_attr_fan2_min.dev_attr.attr,
1302        &sensor_dev_attr_fan2_div.dev_attr.attr,
1303        &sensor_dev_attr_fan2_alarm.dev_attr.attr,
1304        &sensor_dev_attr_fan3_input.dev_attr.attr,
1305        &sensor_dev_attr_fan3_min.dev_attr.attr,
1306        &sensor_dev_attr_fan3_div.dev_attr.attr,
1307        &sensor_dev_attr_fan3_alarm.dev_attr.attr,
1308        NULL
1309};
1310
1311static const struct attribute_group w83792d_group = {
1312        .attrs = w83792d_attributes,
1313};
1314
1315/* Return 0 if detection is successful, -ENODEV otherwise */
1316static int
1317w83792d_detect(struct i2c_client *client, struct i2c_board_info *info)
1318{
1319        struct i2c_adapter *adapter = client->adapter;
1320        int val1, val2;
1321        unsigned short address = client->addr;
1322
1323        if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
1324                return -ENODEV;
1325
1326        if (w83792d_read_value(client, W83792D_REG_CONFIG) & 0x80)
1327                return -ENODEV;
1328
1329        val1 = w83792d_read_value(client, W83792D_REG_BANK);
1330        val2 = w83792d_read_value(client, W83792D_REG_CHIPMAN);
1331        /* Check for Winbond ID if in bank 0 */
1332        if (!(val1 & 0x07)) {  /* is Bank0 */
1333                if ((!(val1 & 0x80) && val2 != 0xa3) ||
1334                    ((val1 & 0x80) && val2 != 0x5c))
1335                        return -ENODEV;
1336        }
1337        /*
1338         * If Winbond chip, address of chip and W83792D_REG_I2C_ADDR
1339         * should match
1340         */
1341        if (w83792d_read_value(client, W83792D_REG_I2C_ADDR) != address)
1342                return -ENODEV;
1343
1344        /*  Put it now into bank 0 and Vendor ID High Byte */
1345        w83792d_write_value(client,
1346                            W83792D_REG_BANK,
1347                            (w83792d_read_value(client,
1348                                W83792D_REG_BANK) & 0x78) | 0x80);
1349
1350        /* Determine the chip type. */
1351        val1 = w83792d_read_value(client, W83792D_REG_WCHIPID);
1352        val2 = w83792d_read_value(client, W83792D_REG_CHIPMAN);
1353        if (val1 != 0x7a || val2 != 0x5c)
1354                return -ENODEV;
1355
1356        strlcpy(info->type, "w83792d", I2C_NAME_SIZE);
1357
1358        return 0;
1359}
1360
1361static int
1362w83792d_probe(struct i2c_client *client, const struct i2c_device_id *id)
1363{
1364        struct w83792d_data *data;
1365        struct device *dev = &client->dev;
1366        int i, val1, err;
1367
1368        data = devm_kzalloc(dev, sizeof(struct w83792d_data), GFP_KERNEL);
1369        if (!data)
1370                return -ENOMEM;
1371
1372        i2c_set_clientdata(client, data);
1373        mutex_init(&data->update_lock);
1374
1375        err = w83792d_detect_subclients(client);
1376        if (err)
1377                return err;
1378
1379        /* Initialize the chip */
1380        w83792d_init_client(client);
1381
1382        /* A few vars need to be filled upon startup */
1383        for (i = 0; i < 7; i++) {
1384                data->fan_min[i] = w83792d_read_value(client,
1385                                        W83792D_REG_FAN_MIN[i]);
1386        }
1387
1388        /* Register sysfs hooks */
1389        err = sysfs_create_group(&dev->kobj, &w83792d_group);
1390        if (err)
1391                return err;
1392
1393        /*
1394         * Read GPIO enable register to check if pins for fan 4,5 are used as
1395         * GPIO
1396         */
1397        val1 = w83792d_read_value(client, W83792D_REG_GPIO_EN);
1398
1399        if (!(val1 & 0x40)) {
1400                err = sysfs_create_group(&dev->kobj, &w83792d_group_fan[0]);
1401                if (err)
1402                        goto exit_remove_files;
1403        }
1404
1405        if (!(val1 & 0x20)) {
1406                err = sysfs_create_group(&dev->kobj, &w83792d_group_fan[1]);
1407                if (err)
1408                        goto exit_remove_files;
1409        }
1410
1411        val1 = w83792d_read_value(client, W83792D_REG_PIN);
1412        if (val1 & 0x40) {
1413                err = sysfs_create_group(&dev->kobj, &w83792d_group_fan[2]);
1414                if (err)
1415                        goto exit_remove_files;
1416        }
1417
1418        if (val1 & 0x04) {
1419                err = sysfs_create_group(&dev->kobj, &w83792d_group_fan[3]);
1420                if (err)
1421                        goto exit_remove_files;
1422        }
1423
1424        data->hwmon_dev = hwmon_device_register(dev);
1425        if (IS_ERR(data->hwmon_dev)) {
1426                err = PTR_ERR(data->hwmon_dev);
1427                goto exit_remove_files;
1428        }
1429
1430        return 0;
1431
1432exit_remove_files:
1433        sysfs_remove_group(&dev->kobj, &w83792d_group);
1434        for (i = 0; i < ARRAY_SIZE(w83792d_group_fan); i++)
1435                sysfs_remove_group(&dev->kobj, &w83792d_group_fan[i]);
1436        return err;
1437}
1438
1439static int
1440w83792d_remove(struct i2c_client *client)
1441{
1442        struct w83792d_data *data = i2c_get_clientdata(client);
1443        int i;
1444
1445        hwmon_device_unregister(data->hwmon_dev);
1446        sysfs_remove_group(&client->dev.kobj, &w83792d_group);
1447        for (i = 0; i < ARRAY_SIZE(w83792d_group_fan); i++)
1448                sysfs_remove_group(&client->dev.kobj,
1449                                   &w83792d_group_fan[i]);
1450
1451        return 0;
1452}
1453
1454static void
1455w83792d_init_client(struct i2c_client *client)
1456{
1457        u8 temp2_cfg, temp3_cfg, vid_in_b;
1458
1459        if (init)
1460                w83792d_write_value(client, W83792D_REG_CONFIG, 0x80);
1461
1462        /*
1463         * Clear the bit6 of W83792D_REG_VID_IN_B(set it into 0):
1464         * W83792D_REG_VID_IN_B bit6 = 0: the high/low limit of
1465         * vin0/vin1 can be modified by user;
1466         * W83792D_REG_VID_IN_B bit6 = 1: the high/low limit of
1467         * vin0/vin1 auto-updated, can NOT be modified by user.
1468         */
1469        vid_in_b = w83792d_read_value(client, W83792D_REG_VID_IN_B);
1470        w83792d_write_value(client, W83792D_REG_VID_IN_B,
1471                            vid_in_b & 0xbf);
1472
1473        temp2_cfg = w83792d_read_value(client, W83792D_REG_TEMP2_CONFIG);
1474        temp3_cfg = w83792d_read_value(client, W83792D_REG_TEMP3_CONFIG);
1475        w83792d_write_value(client, W83792D_REG_TEMP2_CONFIG,
1476                                temp2_cfg & 0xe6);
1477        w83792d_write_value(client, W83792D_REG_TEMP3_CONFIG,
1478                                temp3_cfg & 0xe6);
1479
1480        /* Start monitoring */
1481        w83792d_write_value(client, W83792D_REG_CONFIG,
1482                            (w83792d_read_value(client,
1483                                                W83792D_REG_CONFIG) & 0xf7)
1484                            | 0x01);
1485}
1486
1487static struct w83792d_data *w83792d_update_device(struct device *dev)
1488{
1489        struct i2c_client *client = to_i2c_client(dev);
1490        struct w83792d_data *data = i2c_get_clientdata(client);
1491        int i, j;
1492        u8 reg_array_tmp[4], reg_tmp;
1493
1494        mutex_lock(&data->update_lock);
1495
1496        if (time_after
1497            (jiffies - data->last_updated, (unsigned long) (HZ * 3))
1498            || time_before(jiffies, data->last_updated) || !data->valid) {
1499                dev_dbg(dev, "Starting device update\n");
1500
1501                /* Update the voltages measured value and limits */
1502                for (i = 0; i < 9; i++) {
1503                        data->in[i] = w83792d_read_value(client,
1504                                                W83792D_REG_IN[i]);
1505                        data->in_max[i] = w83792d_read_value(client,
1506                                                W83792D_REG_IN_MAX[i]);
1507                        data->in_min[i] = w83792d_read_value(client,
1508                                                W83792D_REG_IN_MIN[i]);
1509                }
1510                data->low_bits = w83792d_read_value(client,
1511                                                W83792D_REG_LOW_BITS1) +
1512                                 (w83792d_read_value(client,
1513                                                W83792D_REG_LOW_BITS2) << 8);
1514                for (i = 0; i < 7; i++) {
1515                        /* Update the Fan measured value and limits */
1516                        data->fan[i] = w83792d_read_value(client,
1517                                                W83792D_REG_FAN[i]);
1518                        data->fan_min[i] = w83792d_read_value(client,
1519                                                W83792D_REG_FAN_MIN[i]);
1520                        /* Update the PWM/DC Value and PWM/DC flag */
1521                        data->pwm[i] = w83792d_read_value(client,
1522                                                W83792D_REG_PWM[i]);
1523                }
1524
1525                reg_tmp = w83792d_read_value(client, W83792D_REG_FAN_CFG);
1526                data->pwmenable[0] = reg_tmp & 0x03;
1527                data->pwmenable[1] = (reg_tmp>>2) & 0x03;
1528                data->pwmenable[2] = (reg_tmp>>4) & 0x03;
1529
1530                for (i = 0; i < 3; i++) {
1531                        data->temp1[i] = w83792d_read_value(client,
1532                                                        W83792D_REG_TEMP1[i]);
1533                }
1534                for (i = 0; i < 2; i++) {
1535                        for (j = 0; j < 6; j++) {
1536                                data->temp_add[i][j] = w83792d_read_value(
1537                                        client, W83792D_REG_TEMP_ADD[i][j]);
1538                        }
1539                }
1540
1541                /* Update the Fan Divisor */
1542                for (i = 0; i < 4; i++) {
1543                        reg_array_tmp[i] = w83792d_read_value(client,
1544                                                        W83792D_REG_FAN_DIV[i]);
1545                }
1546                data->fan_div[0] = reg_array_tmp[0] & 0x07;
1547                data->fan_div[1] = (reg_array_tmp[0] >> 4) & 0x07;
1548                data->fan_div[2] = reg_array_tmp[1] & 0x07;
1549                data->fan_div[3] = (reg_array_tmp[1] >> 4) & 0x07;
1550                data->fan_div[4] = reg_array_tmp[2] & 0x07;
1551                data->fan_div[5] = (reg_array_tmp[2] >> 4) & 0x07;
1552                data->fan_div[6] = reg_array_tmp[3] & 0x07;
1553
1554                /* Update the realtime status */
1555                data->alarms = w83792d_read_value(client, W83792D_REG_ALARM1) +
1556                        (w83792d_read_value(client, W83792D_REG_ALARM2) << 8) +
1557                        (w83792d_read_value(client, W83792D_REG_ALARM3) << 16);
1558
1559                /* Update CaseOpen status and it's CLR_CHS. */
1560                data->chassis = (w83792d_read_value(client,
1561                        W83792D_REG_CHASSIS) >> 5) & 0x01;
1562
1563                /* Update Thermal Cruise/Smart Fan I target value */
1564                for (i = 0; i < 3; i++) {
1565                        data->thermal_cruise[i] =
1566                                w83792d_read_value(client,
1567                                W83792D_REG_THERMAL[i]) & 0x7f;
1568                }
1569
1570                /* Update Smart Fan I/II tolerance */
1571                reg_tmp = w83792d_read_value(client, W83792D_REG_TOLERANCE[0]);
1572                data->tolerance[0] = reg_tmp & 0x0f;
1573                data->tolerance[1] = (reg_tmp >> 4) & 0x0f;
1574                data->tolerance[2] = w83792d_read_value(client,
1575                                        W83792D_REG_TOLERANCE[2]) & 0x0f;
1576
1577                /* Update Smart Fan II temperature points */
1578                for (i = 0; i < 3; i++) {
1579                        for (j = 0; j < 4; j++) {
1580                                data->sf2_points[i][j]
1581                                  = w83792d_read_value(client,
1582                                        W83792D_REG_POINTS[i][j]) & 0x7f;
1583                        }
1584                }
1585
1586                /* Update Smart Fan II duty cycle levels */
1587                for (i = 0; i < 3; i++) {
1588                        reg_tmp = w83792d_read_value(client,
1589                                                W83792D_REG_LEVELS[i][0]);
1590                        data->sf2_levels[i][0] = reg_tmp & 0x0f;
1591                        data->sf2_levels[i][1] = (reg_tmp >> 4) & 0x0f;
1592                        reg_tmp = w83792d_read_value(client,
1593                                                W83792D_REG_LEVELS[i][2]);
1594                        data->sf2_levels[i][2] = (reg_tmp >> 4) & 0x0f;
1595                        data->sf2_levels[i][3] = reg_tmp & 0x0f;
1596                }
1597
1598                data->last_updated = jiffies;
1599                data->valid = 1;
1600        }
1601
1602        mutex_unlock(&data->update_lock);
1603
1604#ifdef DEBUG
1605        w83792d_print_debug(data, dev);
1606#endif
1607
1608        return data;
1609}
1610
1611#ifdef DEBUG
1612static void w83792d_print_debug(struct w83792d_data *data, struct device *dev)
1613{
1614        int i = 0, j = 0;
1615        dev_dbg(dev, "==========The following is the debug message...========\n");
1616        dev_dbg(dev, "9 set of Voltages: =====>\n");
1617        for (i = 0; i < 9; i++) {
1618                dev_dbg(dev, "vin[%d] is: 0x%x\n", i, data->in[i]);
1619                dev_dbg(dev, "vin[%d] max is: 0x%x\n", i, data->in_max[i]);
1620                dev_dbg(dev, "vin[%d] min is: 0x%x\n", i, data->in_min[i]);
1621        }
1622        dev_dbg(dev, "Low Bit1 is: 0x%x\n", data->low_bits & 0xff);
1623        dev_dbg(dev, "Low Bit2 is: 0x%x\n", data->low_bits >> 8);
1624        dev_dbg(dev, "7 set of Fan Counts and Duty Cycles: =====>\n");
1625        for (i = 0; i < 7; i++) {
1626                dev_dbg(dev, "fan[%d] is: 0x%x\n", i, data->fan[i]);
1627                dev_dbg(dev, "fan[%d] min is: 0x%x\n", i, data->fan_min[i]);
1628                dev_dbg(dev, "pwm[%d]     is: 0x%x\n", i, data->pwm[i]);
1629        }
1630        dev_dbg(dev, "3 set of Temperatures: =====>\n");
1631        for (i = 0; i < 3; i++)
1632                dev_dbg(dev, "temp1[%d] is: 0x%x\n", i, data->temp1[i]);
1633
1634        for (i = 0; i < 2; i++) {
1635                for (j = 0; j < 6; j++) {
1636                        dev_dbg(dev, "temp_add[%d][%d] is: 0x%x\n", i, j,
1637                                                        data->temp_add[i][j]);
1638                }
1639        }
1640
1641        for (i = 0; i < 7; i++)
1642                dev_dbg(dev, "fan_div[%d] is: 0x%x\n", i, data->fan_div[i]);
1643
1644        dev_dbg(dev, "==========End of the debug message...================\n");
1645        dev_dbg(dev, "\n");
1646}
1647#endif
1648
1649module_i2c_driver(w83792d_driver);
1650
1651MODULE_AUTHOR("Shane Huang (Winbond)");
1652MODULE_DESCRIPTION("W83792AD/D driver for linux-2.6");
1653MODULE_LICENSE("GPL");
1654