linux/drivers/mmc/host/meson-gx-mmc.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0-only
   2/*
   3 * Amlogic SD/eMMC driver for the GX/S905 family SoCs
   4 *
   5 * Copyright (c) 2016 BayLibre, SAS.
   6 * Author: Kevin Hilman <khilman@baylibre.com>
   7 */
   8#include <linux/kernel.h>
   9#include <linux/module.h>
  10#include <linux/init.h>
  11#include <linux/delay.h>
  12#include <linux/device.h>
  13#include <linux/iopoll.h>
  14#include <linux/of_device.h>
  15#include <linux/platform_device.h>
  16#include <linux/ioport.h>
  17#include <linux/dma-mapping.h>
  18#include <linux/mmc/host.h>
  19#include <linux/mmc/mmc.h>
  20#include <linux/mmc/sdio.h>
  21#include <linux/mmc/slot-gpio.h>
  22#include <linux/io.h>
  23#include <linux/clk.h>
  24#include <linux/clk-provider.h>
  25#include <linux/regulator/consumer.h>
  26#include <linux/reset.h>
  27#include <linux/interrupt.h>
  28#include <linux/bitfield.h>
  29#include <linux/pinctrl/consumer.h>
  30
  31#define DRIVER_NAME "meson-gx-mmc"
  32
  33#define SD_EMMC_CLOCK 0x0
  34#define   CLK_DIV_MASK GENMASK(5, 0)
  35#define   CLK_SRC_MASK GENMASK(7, 6)
  36#define   CLK_CORE_PHASE_MASK GENMASK(9, 8)
  37#define   CLK_TX_PHASE_MASK GENMASK(11, 10)
  38#define   CLK_RX_PHASE_MASK GENMASK(13, 12)
  39#define   CLK_PHASE_0 0
  40#define   CLK_PHASE_180 2
  41#define   CLK_V2_TX_DELAY_MASK GENMASK(19, 16)
  42#define   CLK_V2_RX_DELAY_MASK GENMASK(23, 20)
  43#define   CLK_V2_ALWAYS_ON BIT(24)
  44
  45#define   CLK_V3_TX_DELAY_MASK GENMASK(21, 16)
  46#define   CLK_V3_RX_DELAY_MASK GENMASK(27, 22)
  47#define   CLK_V3_ALWAYS_ON BIT(28)
  48
  49#define   CLK_TX_DELAY_MASK(h)          (h->data->tx_delay_mask)
  50#define   CLK_RX_DELAY_MASK(h)          (h->data->rx_delay_mask)
  51#define   CLK_ALWAYS_ON(h)              (h->data->always_on)
  52
  53#define SD_EMMC_DELAY 0x4
  54#define SD_EMMC_ADJUST 0x8
  55#define   ADJUST_ADJ_DELAY_MASK GENMASK(21, 16)
  56#define   ADJUST_DS_EN BIT(15)
  57#define   ADJUST_ADJ_EN BIT(13)
  58
  59#define SD_EMMC_DELAY1 0x4
  60#define SD_EMMC_DELAY2 0x8
  61#define SD_EMMC_V3_ADJUST 0xc
  62
  63#define SD_EMMC_CALOUT 0x10
  64#define SD_EMMC_START 0x40
  65#define   START_DESC_INIT BIT(0)
  66#define   START_DESC_BUSY BIT(1)
  67#define   START_DESC_ADDR_MASK GENMASK(31, 2)
  68
  69#define SD_EMMC_CFG 0x44
  70#define   CFG_BUS_WIDTH_MASK GENMASK(1, 0)
  71#define   CFG_BUS_WIDTH_1 0x0
  72#define   CFG_BUS_WIDTH_4 0x1
  73#define   CFG_BUS_WIDTH_8 0x2
  74#define   CFG_DDR BIT(2)
  75#define   CFG_BLK_LEN_MASK GENMASK(7, 4)
  76#define   CFG_RESP_TIMEOUT_MASK GENMASK(11, 8)
  77#define   CFG_RC_CC_MASK GENMASK(15, 12)
  78#define   CFG_STOP_CLOCK BIT(22)
  79#define   CFG_CLK_ALWAYS_ON BIT(18)
  80#define   CFG_CHK_DS BIT(20)
  81#define   CFG_AUTO_CLK BIT(23)
  82#define   CFG_ERR_ABORT BIT(27)
  83
  84#define SD_EMMC_STATUS 0x48
  85#define   STATUS_BUSY BIT(31)
  86#define   STATUS_DESC_BUSY BIT(30)
  87#define   STATUS_DATI GENMASK(23, 16)
  88
  89#define SD_EMMC_IRQ_EN 0x4c
  90#define   IRQ_RXD_ERR_MASK GENMASK(7, 0)
  91#define   IRQ_TXD_ERR BIT(8)
  92#define   IRQ_DESC_ERR BIT(9)
  93#define   IRQ_RESP_ERR BIT(10)
  94#define   IRQ_CRC_ERR \
  95        (IRQ_RXD_ERR_MASK | IRQ_TXD_ERR | IRQ_DESC_ERR | IRQ_RESP_ERR)
  96#define   IRQ_RESP_TIMEOUT BIT(11)
  97#define   IRQ_DESC_TIMEOUT BIT(12)
  98#define   IRQ_TIMEOUTS \
  99        (IRQ_RESP_TIMEOUT | IRQ_DESC_TIMEOUT)
 100#define   IRQ_END_OF_CHAIN BIT(13)
 101#define   IRQ_RESP_STATUS BIT(14)
 102#define   IRQ_SDIO BIT(15)
 103#define   IRQ_EN_MASK \
 104        (IRQ_CRC_ERR | IRQ_TIMEOUTS | IRQ_END_OF_CHAIN | IRQ_RESP_STATUS |\
 105         IRQ_SDIO)
 106
 107#define SD_EMMC_CMD_CFG 0x50
 108#define SD_EMMC_CMD_ARG 0x54
 109#define SD_EMMC_CMD_DAT 0x58
 110#define SD_EMMC_CMD_RSP 0x5c
 111#define SD_EMMC_CMD_RSP1 0x60
 112#define SD_EMMC_CMD_RSP2 0x64
 113#define SD_EMMC_CMD_RSP3 0x68
 114
 115#define SD_EMMC_RXD 0x94
 116#define SD_EMMC_TXD 0x94
 117#define SD_EMMC_LAST_REG SD_EMMC_TXD
 118
 119#define SD_EMMC_SRAM_DATA_BUF_LEN 1536
 120#define SD_EMMC_SRAM_DATA_BUF_OFF 0x200
 121
 122#define SD_EMMC_CFG_BLK_SIZE 512 /* internal buffer max: 512 bytes */
 123#define SD_EMMC_CFG_RESP_TIMEOUT 256 /* in clock cycles */
 124#define SD_EMMC_CMD_TIMEOUT 1024 /* in ms */
 125#define SD_EMMC_CMD_TIMEOUT_DATA 4096 /* in ms */
 126#define SD_EMMC_CFG_CMD_GAP 16 /* in clock cycles */
 127#define SD_EMMC_DESC_BUF_LEN PAGE_SIZE
 128
 129#define SD_EMMC_PRE_REQ_DONE BIT(0)
 130#define SD_EMMC_DESC_CHAIN_MODE BIT(1)
 131
 132#define MUX_CLK_NUM_PARENTS 2
 133
 134struct meson_mmc_data {
 135        unsigned int tx_delay_mask;
 136        unsigned int rx_delay_mask;
 137        unsigned int always_on;
 138        unsigned int adjust;
 139};
 140
 141struct sd_emmc_desc {
 142        u32 cmd_cfg;
 143        u32 cmd_arg;
 144        u32 cmd_data;
 145        u32 cmd_resp;
 146};
 147
 148struct meson_host {
 149        struct  device          *dev;
 150        struct  meson_mmc_data *data;
 151        struct  mmc_host        *mmc;
 152        struct  mmc_command     *cmd;
 153
 154        void __iomem *regs;
 155        struct clk *core_clk;
 156        struct clk *mux_clk;
 157        struct clk *mmc_clk;
 158        unsigned long req_rate;
 159        bool ddr;
 160
 161        bool dram_access_quirk;
 162
 163        struct pinctrl *pinctrl;
 164        struct pinctrl_state *pins_clk_gate;
 165
 166        unsigned int bounce_buf_size;
 167        void *bounce_buf;
 168        dma_addr_t bounce_dma_addr;
 169        struct sd_emmc_desc *descs;
 170        dma_addr_t descs_dma_addr;
 171
 172        int irq;
 173
 174        bool vqmmc_enabled;
 175};
 176
 177#define CMD_CFG_LENGTH_MASK GENMASK(8, 0)
 178#define CMD_CFG_BLOCK_MODE BIT(9)
 179#define CMD_CFG_R1B BIT(10)
 180#define CMD_CFG_END_OF_CHAIN BIT(11)
 181#define CMD_CFG_TIMEOUT_MASK GENMASK(15, 12)
 182#define CMD_CFG_NO_RESP BIT(16)
 183#define CMD_CFG_NO_CMD BIT(17)
 184#define CMD_CFG_DATA_IO BIT(18)
 185#define CMD_CFG_DATA_WR BIT(19)
 186#define CMD_CFG_RESP_NOCRC BIT(20)
 187#define CMD_CFG_RESP_128 BIT(21)
 188#define CMD_CFG_RESP_NUM BIT(22)
 189#define CMD_CFG_DATA_NUM BIT(23)
 190#define CMD_CFG_CMD_INDEX_MASK GENMASK(29, 24)
 191#define CMD_CFG_ERROR BIT(30)
 192#define CMD_CFG_OWNER BIT(31)
 193
 194#define CMD_DATA_MASK GENMASK(31, 2)
 195#define CMD_DATA_BIG_ENDIAN BIT(1)
 196#define CMD_DATA_SRAM BIT(0)
 197#define CMD_RESP_MASK GENMASK(31, 1)
 198#define CMD_RESP_SRAM BIT(0)
 199
 200static unsigned int meson_mmc_get_timeout_msecs(struct mmc_data *data)
 201{
 202        unsigned int timeout = data->timeout_ns / NSEC_PER_MSEC;
 203
 204        if (!timeout)
 205                return SD_EMMC_CMD_TIMEOUT_DATA;
 206
 207        timeout = roundup_pow_of_two(timeout);
 208
 209        return min(timeout, 32768U); /* max. 2^15 ms */
 210}
 211
 212static struct mmc_command *meson_mmc_get_next_command(struct mmc_command *cmd)
 213{
 214        if (cmd->opcode == MMC_SET_BLOCK_COUNT && !cmd->error)
 215                return cmd->mrq->cmd;
 216        else if (mmc_op_multi(cmd->opcode) &&
 217                 (!cmd->mrq->sbc || cmd->error || cmd->data->error))
 218                return cmd->mrq->stop;
 219        else
 220                return NULL;
 221}
 222
 223static void meson_mmc_get_transfer_mode(struct mmc_host *mmc,
 224                                        struct mmc_request *mrq)
 225{
 226        struct meson_host *host = mmc_priv(mmc);
 227        struct mmc_data *data = mrq->data;
 228        struct scatterlist *sg;
 229        int i;
 230        bool use_desc_chain_mode = true;
 231
 232        /*
 233         * When Controller DMA cannot directly access DDR memory, disable
 234         * support for Chain Mode to directly use the internal SRAM using
 235         * the bounce buffer mode.
 236         */
 237        if (host->dram_access_quirk)
 238                return;
 239
 240        /*
 241         * Broken SDIO with AP6255-based WiFi on Khadas VIM Pro has been
 242         * reported. For some strange reason this occurs in descriptor
 243         * chain mode only. So let's fall back to bounce buffer mode
 244         * for command SD_IO_RW_EXTENDED.
 245         */
 246        if (mrq->cmd->opcode == SD_IO_RW_EXTENDED)
 247                return;
 248
 249        for_each_sg(data->sg, sg, data->sg_len, i)
 250                /* check for 8 byte alignment */
 251                if (sg->offset & 7) {
 252                        WARN_ONCE(1, "unaligned scatterlist buffer\n");
 253                        use_desc_chain_mode = false;
 254                        break;
 255                }
 256
 257        if (use_desc_chain_mode)
 258                data->host_cookie |= SD_EMMC_DESC_CHAIN_MODE;
 259}
 260
 261static inline bool meson_mmc_desc_chain_mode(const struct mmc_data *data)
 262{
 263        return data->host_cookie & SD_EMMC_DESC_CHAIN_MODE;
 264}
 265
 266static inline bool meson_mmc_bounce_buf_read(const struct mmc_data *data)
 267{
 268        return data && data->flags & MMC_DATA_READ &&
 269               !meson_mmc_desc_chain_mode(data);
 270}
 271
 272static void meson_mmc_pre_req(struct mmc_host *mmc, struct mmc_request *mrq)
 273{
 274        struct mmc_data *data = mrq->data;
 275
 276        if (!data)
 277                return;
 278
 279        meson_mmc_get_transfer_mode(mmc, mrq);
 280        data->host_cookie |= SD_EMMC_PRE_REQ_DONE;
 281
 282        if (!meson_mmc_desc_chain_mode(data))
 283                return;
 284
 285        data->sg_count = dma_map_sg(mmc_dev(mmc), data->sg, data->sg_len,
 286                                   mmc_get_dma_dir(data));
 287        if (!data->sg_count)
 288                dev_err(mmc_dev(mmc), "dma_map_sg failed");
 289}
 290
 291static void meson_mmc_post_req(struct mmc_host *mmc, struct mmc_request *mrq,
 292                               int err)
 293{
 294        struct mmc_data *data = mrq->data;
 295
 296        if (data && meson_mmc_desc_chain_mode(data) && data->sg_count)
 297                dma_unmap_sg(mmc_dev(mmc), data->sg, data->sg_len,
 298                             mmc_get_dma_dir(data));
 299}
 300
 301/*
 302 * Gating the clock on this controller is tricky.  It seems the mmc clock
 303 * is also used by the controller.  It may crash during some operation if the
 304 * clock is stopped.  The safest thing to do, whenever possible, is to keep
 305 * clock running at stop it at the pad using the pinmux.
 306 */
 307static void meson_mmc_clk_gate(struct meson_host *host)
 308{
 309        u32 cfg;
 310
 311        if (host->pins_clk_gate) {
 312                pinctrl_select_state(host->pinctrl, host->pins_clk_gate);
 313        } else {
 314                /*
 315                 * If the pinmux is not provided - default to the classic and
 316                 * unsafe method
 317                 */
 318                cfg = readl(host->regs + SD_EMMC_CFG);
 319                cfg |= CFG_STOP_CLOCK;
 320                writel(cfg, host->regs + SD_EMMC_CFG);
 321        }
 322}
 323
 324static void meson_mmc_clk_ungate(struct meson_host *host)
 325{
 326        u32 cfg;
 327
 328        if (host->pins_clk_gate)
 329                pinctrl_select_default_state(host->dev);
 330
 331        /* Make sure the clock is not stopped in the controller */
 332        cfg = readl(host->regs + SD_EMMC_CFG);
 333        cfg &= ~CFG_STOP_CLOCK;
 334        writel(cfg, host->regs + SD_EMMC_CFG);
 335}
 336
 337static int meson_mmc_clk_set(struct meson_host *host, unsigned long rate,
 338                             bool ddr)
 339{
 340        struct mmc_host *mmc = host->mmc;
 341        int ret;
 342        u32 cfg;
 343
 344        /* Same request - bail-out */
 345        if (host->ddr == ddr && host->req_rate == rate)
 346                return 0;
 347
 348        /* stop clock */
 349        meson_mmc_clk_gate(host);
 350        host->req_rate = 0;
 351        mmc->actual_clock = 0;
 352
 353        /* return with clock being stopped */
 354        if (!rate)
 355                return 0;
 356
 357        /* Stop the clock during rate change to avoid glitches */
 358        cfg = readl(host->regs + SD_EMMC_CFG);
 359        cfg |= CFG_STOP_CLOCK;
 360        writel(cfg, host->regs + SD_EMMC_CFG);
 361
 362        if (ddr) {
 363                /* DDR modes require higher module clock */
 364                rate <<= 1;
 365                cfg |= CFG_DDR;
 366        } else {
 367                cfg &= ~CFG_DDR;
 368        }
 369        writel(cfg, host->regs + SD_EMMC_CFG);
 370        host->ddr = ddr;
 371
 372        ret = clk_set_rate(host->mmc_clk, rate);
 373        if (ret) {
 374                dev_err(host->dev, "Unable to set cfg_div_clk to %lu. ret=%d\n",
 375                        rate, ret);
 376                return ret;
 377        }
 378
 379        host->req_rate = rate;
 380        mmc->actual_clock = clk_get_rate(host->mmc_clk);
 381
 382        /* We should report the real output frequency of the controller */
 383        if (ddr) {
 384                host->req_rate >>= 1;
 385                mmc->actual_clock >>= 1;
 386        }
 387
 388        dev_dbg(host->dev, "clk rate: %u Hz\n", mmc->actual_clock);
 389        if (rate != mmc->actual_clock)
 390                dev_dbg(host->dev, "requested rate was %lu\n", rate);
 391
 392        /* (re)start clock */
 393        meson_mmc_clk_ungate(host);
 394
 395        return 0;
 396}
 397
 398/*
 399 * The SD/eMMC IP block has an internal mux and divider used for
 400 * generating the MMC clock.  Use the clock framework to create and
 401 * manage these clocks.
 402 */
 403static int meson_mmc_clk_init(struct meson_host *host)
 404{
 405        struct clk_init_data init;
 406        struct clk_mux *mux;
 407        struct clk_divider *div;
 408        char clk_name[32];
 409        int i, ret = 0;
 410        const char *mux_parent_names[MUX_CLK_NUM_PARENTS];
 411        const char *clk_parent[1];
 412        u32 clk_reg;
 413
 414        /* init SD_EMMC_CLOCK to sane defaults w/min clock rate */
 415        clk_reg = CLK_ALWAYS_ON(host);
 416        clk_reg |= CLK_DIV_MASK;
 417        clk_reg |= FIELD_PREP(CLK_CORE_PHASE_MASK, CLK_PHASE_180);
 418        clk_reg |= FIELD_PREP(CLK_TX_PHASE_MASK, CLK_PHASE_0);
 419        clk_reg |= FIELD_PREP(CLK_RX_PHASE_MASK, CLK_PHASE_0);
 420        writel(clk_reg, host->regs + SD_EMMC_CLOCK);
 421
 422        /* get the mux parents */
 423        for (i = 0; i < MUX_CLK_NUM_PARENTS; i++) {
 424                struct clk *clk;
 425                char name[16];
 426
 427                snprintf(name, sizeof(name), "clkin%d", i);
 428                clk = devm_clk_get(host->dev, name);
 429                if (IS_ERR(clk)) {
 430                        if (clk != ERR_PTR(-EPROBE_DEFER))
 431                                dev_err(host->dev, "Missing clock %s\n", name);
 432                        return PTR_ERR(clk);
 433                }
 434
 435                mux_parent_names[i] = __clk_get_name(clk);
 436        }
 437
 438        /* create the mux */
 439        mux = devm_kzalloc(host->dev, sizeof(*mux), GFP_KERNEL);
 440        if (!mux)
 441                return -ENOMEM;
 442
 443        snprintf(clk_name, sizeof(clk_name), "%s#mux", dev_name(host->dev));
 444        init.name = clk_name;
 445        init.ops = &clk_mux_ops;
 446        init.flags = 0;
 447        init.parent_names = mux_parent_names;
 448        init.num_parents = MUX_CLK_NUM_PARENTS;
 449
 450        mux->reg = host->regs + SD_EMMC_CLOCK;
 451        mux->shift = __ffs(CLK_SRC_MASK);
 452        mux->mask = CLK_SRC_MASK >> mux->shift;
 453        mux->hw.init = &init;
 454
 455        host->mux_clk = devm_clk_register(host->dev, &mux->hw);
 456        if (WARN_ON(IS_ERR(host->mux_clk)))
 457                return PTR_ERR(host->mux_clk);
 458
 459        /* create the divider */
 460        div = devm_kzalloc(host->dev, sizeof(*div), GFP_KERNEL);
 461        if (!div)
 462                return -ENOMEM;
 463
 464        snprintf(clk_name, sizeof(clk_name), "%s#div", dev_name(host->dev));
 465        init.name = clk_name;
 466        init.ops = &clk_divider_ops;
 467        init.flags = CLK_SET_RATE_PARENT;
 468        clk_parent[0] = __clk_get_name(host->mux_clk);
 469        init.parent_names = clk_parent;
 470        init.num_parents = 1;
 471
 472        div->reg = host->regs + SD_EMMC_CLOCK;
 473        div->shift = __ffs(CLK_DIV_MASK);
 474        div->width = __builtin_popcountl(CLK_DIV_MASK);
 475        div->hw.init = &init;
 476        div->flags = CLK_DIVIDER_ONE_BASED;
 477
 478        host->mmc_clk = devm_clk_register(host->dev, &div->hw);
 479        if (WARN_ON(IS_ERR(host->mmc_clk)))
 480                return PTR_ERR(host->mmc_clk);
 481
 482        /* init SD_EMMC_CLOCK to sane defaults w/min clock rate */
 483        host->mmc->f_min = clk_round_rate(host->mmc_clk, 400000);
 484        ret = clk_set_rate(host->mmc_clk, host->mmc->f_min);
 485        if (ret)
 486                return ret;
 487
 488        return clk_prepare_enable(host->mmc_clk);
 489}
 490
 491static void meson_mmc_disable_resampling(struct meson_host *host)
 492{
 493        unsigned int val = readl(host->regs + host->data->adjust);
 494
 495        val &= ~ADJUST_ADJ_EN;
 496        writel(val, host->regs + host->data->adjust);
 497}
 498
 499static void meson_mmc_reset_resampling(struct meson_host *host)
 500{
 501        unsigned int val;
 502
 503        meson_mmc_disable_resampling(host);
 504
 505        val = readl(host->regs + host->data->adjust);
 506        val &= ~ADJUST_ADJ_DELAY_MASK;
 507        writel(val, host->regs + host->data->adjust);
 508}
 509
 510static int meson_mmc_resampling_tuning(struct mmc_host *mmc, u32 opcode)
 511{
 512        struct meson_host *host = mmc_priv(mmc);
 513        unsigned int val, dly, max_dly, i;
 514        int ret;
 515
 516        /* Resampling is done using the source clock */
 517        max_dly = DIV_ROUND_UP(clk_get_rate(host->mux_clk),
 518                               clk_get_rate(host->mmc_clk));
 519
 520        val = readl(host->regs + host->data->adjust);
 521        val |= ADJUST_ADJ_EN;
 522        writel(val, host->regs + host->data->adjust);
 523
 524        if (mmc->doing_retune)
 525                dly = FIELD_GET(ADJUST_ADJ_DELAY_MASK, val) + 1;
 526        else
 527                dly = 0;
 528
 529        for (i = 0; i < max_dly; i++) {
 530                val &= ~ADJUST_ADJ_DELAY_MASK;
 531                val |= FIELD_PREP(ADJUST_ADJ_DELAY_MASK, (dly + i) % max_dly);
 532                writel(val, host->regs + host->data->adjust);
 533
 534                ret = mmc_send_tuning(mmc, opcode, NULL);
 535                if (!ret) {
 536                        dev_dbg(mmc_dev(mmc), "resampling delay: %u\n",
 537                                (dly + i) % max_dly);
 538                        return 0;
 539                }
 540        }
 541
 542        meson_mmc_reset_resampling(host);
 543        return -EIO;
 544}
 545
 546static int meson_mmc_prepare_ios_clock(struct meson_host *host,
 547                                       struct mmc_ios *ios)
 548{
 549        bool ddr;
 550
 551        switch (ios->timing) {
 552        case MMC_TIMING_MMC_DDR52:
 553        case MMC_TIMING_UHS_DDR50:
 554                ddr = true;
 555                break;
 556
 557        default:
 558                ddr = false;
 559                break;
 560        }
 561
 562        return meson_mmc_clk_set(host, ios->clock, ddr);
 563}
 564
 565static void meson_mmc_check_resampling(struct meson_host *host,
 566                                       struct mmc_ios *ios)
 567{
 568        switch (ios->timing) {
 569        case MMC_TIMING_LEGACY:
 570        case MMC_TIMING_MMC_HS:
 571        case MMC_TIMING_SD_HS:
 572        case MMC_TIMING_MMC_DDR52:
 573                meson_mmc_disable_resampling(host);
 574                break;
 575        }
 576}
 577
 578static void meson_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 579{
 580        struct meson_host *host = mmc_priv(mmc);
 581        u32 bus_width, val;
 582        int err;
 583
 584        /*
 585         * GPIO regulator, only controls switching between 1v8 and
 586         * 3v3, doesn't support MMC_POWER_OFF, MMC_POWER_ON.
 587         */
 588        switch (ios->power_mode) {
 589        case MMC_POWER_OFF:
 590                if (!IS_ERR(mmc->supply.vmmc))
 591                        mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
 592
 593                if (!IS_ERR(mmc->supply.vqmmc) && host->vqmmc_enabled) {
 594                        regulator_disable(mmc->supply.vqmmc);
 595                        host->vqmmc_enabled = false;
 596                }
 597
 598                break;
 599
 600        case MMC_POWER_UP:
 601                if (!IS_ERR(mmc->supply.vmmc))
 602                        mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd);
 603
 604                break;
 605
 606        case MMC_POWER_ON:
 607                if (!IS_ERR(mmc->supply.vqmmc) && !host->vqmmc_enabled) {
 608                        int ret = regulator_enable(mmc->supply.vqmmc);
 609
 610                        if (ret < 0)
 611                                dev_err(host->dev,
 612                                        "failed to enable vqmmc regulator\n");
 613                        else
 614                                host->vqmmc_enabled = true;
 615                }
 616
 617                break;
 618        }
 619
 620        /* Bus width */
 621        switch (ios->bus_width) {
 622        case MMC_BUS_WIDTH_1:
 623                bus_width = CFG_BUS_WIDTH_1;
 624                break;
 625        case MMC_BUS_WIDTH_4:
 626                bus_width = CFG_BUS_WIDTH_4;
 627                break;
 628        case MMC_BUS_WIDTH_8:
 629                bus_width = CFG_BUS_WIDTH_8;
 630                break;
 631        default:
 632                dev_err(host->dev, "Invalid ios->bus_width: %u.  Setting to 4.\n",
 633                        ios->bus_width);
 634                bus_width = CFG_BUS_WIDTH_4;
 635        }
 636
 637        val = readl(host->regs + SD_EMMC_CFG);
 638        val &= ~CFG_BUS_WIDTH_MASK;
 639        val |= FIELD_PREP(CFG_BUS_WIDTH_MASK, bus_width);
 640        writel(val, host->regs + SD_EMMC_CFG);
 641
 642        meson_mmc_check_resampling(host, ios);
 643        err = meson_mmc_prepare_ios_clock(host, ios);
 644        if (err)
 645                dev_err(host->dev, "Failed to set clock: %d\n,", err);
 646
 647        dev_dbg(host->dev, "SD_EMMC_CFG:  0x%08x\n", val);
 648}
 649
 650static void meson_mmc_request_done(struct mmc_host *mmc,
 651                                   struct mmc_request *mrq)
 652{
 653        struct meson_host *host = mmc_priv(mmc);
 654
 655        host->cmd = NULL;
 656        mmc_request_done(host->mmc, mrq);
 657}
 658
 659static void meson_mmc_set_blksz(struct mmc_host *mmc, unsigned int blksz)
 660{
 661        struct meson_host *host = mmc_priv(mmc);
 662        u32 cfg, blksz_old;
 663
 664        cfg = readl(host->regs + SD_EMMC_CFG);
 665        blksz_old = FIELD_GET(CFG_BLK_LEN_MASK, cfg);
 666
 667        if (!is_power_of_2(blksz))
 668                dev_err(host->dev, "blksz %u is not a power of 2\n", blksz);
 669
 670        blksz = ilog2(blksz);
 671
 672        /* check if block-size matches, if not update */
 673        if (blksz == blksz_old)
 674                return;
 675
 676        dev_dbg(host->dev, "%s: update blk_len %d -> %d\n", __func__,
 677                blksz_old, blksz);
 678
 679        cfg &= ~CFG_BLK_LEN_MASK;
 680        cfg |= FIELD_PREP(CFG_BLK_LEN_MASK, blksz);
 681        writel(cfg, host->regs + SD_EMMC_CFG);
 682}
 683
 684static void meson_mmc_set_response_bits(struct mmc_command *cmd, u32 *cmd_cfg)
 685{
 686        if (cmd->flags & MMC_RSP_PRESENT) {
 687                if (cmd->flags & MMC_RSP_136)
 688                        *cmd_cfg |= CMD_CFG_RESP_128;
 689                *cmd_cfg |= CMD_CFG_RESP_NUM;
 690
 691                if (!(cmd->flags & MMC_RSP_CRC))
 692                        *cmd_cfg |= CMD_CFG_RESP_NOCRC;
 693
 694                if (cmd->flags & MMC_RSP_BUSY)
 695                        *cmd_cfg |= CMD_CFG_R1B;
 696        } else {
 697                *cmd_cfg |= CMD_CFG_NO_RESP;
 698        }
 699}
 700
 701static void meson_mmc_desc_chain_transfer(struct mmc_host *mmc, u32 cmd_cfg)
 702{
 703        struct meson_host *host = mmc_priv(mmc);
 704        struct sd_emmc_desc *desc = host->descs;
 705        struct mmc_data *data = host->cmd->data;
 706        struct scatterlist *sg;
 707        u32 start;
 708        int i;
 709
 710        if (data->flags & MMC_DATA_WRITE)
 711                cmd_cfg |= CMD_CFG_DATA_WR;
 712
 713        if (data->blocks > 1) {
 714                cmd_cfg |= CMD_CFG_BLOCK_MODE;
 715                meson_mmc_set_blksz(mmc, data->blksz);
 716        }
 717
 718        for_each_sg(data->sg, sg, data->sg_count, i) {
 719                unsigned int len = sg_dma_len(sg);
 720
 721                if (data->blocks > 1)
 722                        len /= data->blksz;
 723
 724                desc[i].cmd_cfg = cmd_cfg;
 725                desc[i].cmd_cfg |= FIELD_PREP(CMD_CFG_LENGTH_MASK, len);
 726                if (i > 0)
 727                        desc[i].cmd_cfg |= CMD_CFG_NO_CMD;
 728                desc[i].cmd_arg = host->cmd->arg;
 729                desc[i].cmd_resp = 0;
 730                desc[i].cmd_data = sg_dma_address(sg);
 731        }
 732        desc[data->sg_count - 1].cmd_cfg |= CMD_CFG_END_OF_CHAIN;
 733
 734        dma_wmb(); /* ensure descriptor is written before kicked */
 735        start = host->descs_dma_addr | START_DESC_BUSY;
 736        writel(start, host->regs + SD_EMMC_START);
 737}
 738
 739static void meson_mmc_start_cmd(struct mmc_host *mmc, struct mmc_command *cmd)
 740{
 741        struct meson_host *host = mmc_priv(mmc);
 742        struct mmc_data *data = cmd->data;
 743        u32 cmd_cfg = 0, cmd_data = 0;
 744        unsigned int xfer_bytes = 0;
 745
 746        /* Setup descriptors */
 747        dma_rmb();
 748
 749        host->cmd = cmd;
 750
 751        cmd_cfg |= FIELD_PREP(CMD_CFG_CMD_INDEX_MASK, cmd->opcode);
 752        cmd_cfg |= CMD_CFG_OWNER;  /* owned by CPU */
 753        cmd_cfg |= CMD_CFG_ERROR; /* stop in case of error */
 754
 755        meson_mmc_set_response_bits(cmd, &cmd_cfg);
 756
 757        /* data? */
 758        if (data) {
 759                data->bytes_xfered = 0;
 760                cmd_cfg |= CMD_CFG_DATA_IO;
 761                cmd_cfg |= FIELD_PREP(CMD_CFG_TIMEOUT_MASK,
 762                                      ilog2(meson_mmc_get_timeout_msecs(data)));
 763
 764                if (meson_mmc_desc_chain_mode(data)) {
 765                        meson_mmc_desc_chain_transfer(mmc, cmd_cfg);
 766                        return;
 767                }
 768
 769                if (data->blocks > 1) {
 770                        cmd_cfg |= CMD_CFG_BLOCK_MODE;
 771                        cmd_cfg |= FIELD_PREP(CMD_CFG_LENGTH_MASK,
 772                                              data->blocks);
 773                        meson_mmc_set_blksz(mmc, data->blksz);
 774                } else {
 775                        cmd_cfg |= FIELD_PREP(CMD_CFG_LENGTH_MASK, data->blksz);
 776                }
 777
 778                xfer_bytes = data->blksz * data->blocks;
 779                if (data->flags & MMC_DATA_WRITE) {
 780                        cmd_cfg |= CMD_CFG_DATA_WR;
 781                        WARN_ON(xfer_bytes > host->bounce_buf_size);
 782                        sg_copy_to_buffer(data->sg, data->sg_len,
 783                                          host->bounce_buf, xfer_bytes);
 784                        dma_wmb();
 785                }
 786
 787                cmd_data = host->bounce_dma_addr & CMD_DATA_MASK;
 788        } else {
 789                cmd_cfg |= FIELD_PREP(CMD_CFG_TIMEOUT_MASK,
 790                                      ilog2(SD_EMMC_CMD_TIMEOUT));
 791        }
 792
 793        /* Last descriptor */
 794        cmd_cfg |= CMD_CFG_END_OF_CHAIN;
 795        writel(cmd_cfg, host->regs + SD_EMMC_CMD_CFG);
 796        writel(cmd_data, host->regs + SD_EMMC_CMD_DAT);
 797        writel(0, host->regs + SD_EMMC_CMD_RSP);
 798        wmb(); /* ensure descriptor is written before kicked */
 799        writel(cmd->arg, host->regs + SD_EMMC_CMD_ARG);
 800}
 801
 802static void meson_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
 803{
 804        struct meson_host *host = mmc_priv(mmc);
 805        bool needs_pre_post_req = mrq->data &&
 806                        !(mrq->data->host_cookie & SD_EMMC_PRE_REQ_DONE);
 807
 808        if (needs_pre_post_req) {
 809                meson_mmc_get_transfer_mode(mmc, mrq);
 810                if (!meson_mmc_desc_chain_mode(mrq->data))
 811                        needs_pre_post_req = false;
 812        }
 813
 814        if (needs_pre_post_req)
 815                meson_mmc_pre_req(mmc, mrq);
 816
 817        /* Stop execution */
 818        writel(0, host->regs + SD_EMMC_START);
 819
 820        meson_mmc_start_cmd(mmc, mrq->sbc ?: mrq->cmd);
 821
 822        if (needs_pre_post_req)
 823                meson_mmc_post_req(mmc, mrq, 0);
 824}
 825
 826static void meson_mmc_read_resp(struct mmc_host *mmc, struct mmc_command *cmd)
 827{
 828        struct meson_host *host = mmc_priv(mmc);
 829
 830        if (cmd->flags & MMC_RSP_136) {
 831                cmd->resp[0] = readl(host->regs + SD_EMMC_CMD_RSP3);
 832                cmd->resp[1] = readl(host->regs + SD_EMMC_CMD_RSP2);
 833                cmd->resp[2] = readl(host->regs + SD_EMMC_CMD_RSP1);
 834                cmd->resp[3] = readl(host->regs + SD_EMMC_CMD_RSP);
 835        } else if (cmd->flags & MMC_RSP_PRESENT) {
 836                cmd->resp[0] = readl(host->regs + SD_EMMC_CMD_RSP);
 837        }
 838}
 839
 840static irqreturn_t meson_mmc_irq(int irq, void *dev_id)
 841{
 842        struct meson_host *host = dev_id;
 843        struct mmc_command *cmd;
 844        struct mmc_data *data;
 845        u32 irq_en, status, raw_status;
 846        irqreturn_t ret = IRQ_NONE;
 847
 848        irq_en = readl(host->regs + SD_EMMC_IRQ_EN);
 849        raw_status = readl(host->regs + SD_EMMC_STATUS);
 850        status = raw_status & irq_en;
 851
 852        if (!status) {
 853                dev_dbg(host->dev,
 854                        "Unexpected IRQ! irq_en 0x%08x - status 0x%08x\n",
 855                         irq_en, raw_status);
 856                return IRQ_NONE;
 857        }
 858
 859        if (WARN_ON(!host) || WARN_ON(!host->cmd))
 860                return IRQ_NONE;
 861
 862        /* ack all raised interrupts */
 863        writel(status, host->regs + SD_EMMC_STATUS);
 864
 865        cmd = host->cmd;
 866        data = cmd->data;
 867        cmd->error = 0;
 868        if (status & IRQ_CRC_ERR) {
 869                dev_dbg(host->dev, "CRC Error - status 0x%08x\n", status);
 870                cmd->error = -EILSEQ;
 871                ret = IRQ_WAKE_THREAD;
 872                goto out;
 873        }
 874
 875        if (status & IRQ_TIMEOUTS) {
 876                dev_dbg(host->dev, "Timeout - status 0x%08x\n", status);
 877                cmd->error = -ETIMEDOUT;
 878                ret = IRQ_WAKE_THREAD;
 879                goto out;
 880        }
 881
 882        meson_mmc_read_resp(host->mmc, cmd);
 883
 884        if (status & IRQ_SDIO) {
 885                dev_dbg(host->dev, "IRQ: SDIO TODO.\n");
 886                ret = IRQ_HANDLED;
 887        }
 888
 889        if (status & (IRQ_END_OF_CHAIN | IRQ_RESP_STATUS)) {
 890                if (data && !cmd->error)
 891                        data->bytes_xfered = data->blksz * data->blocks;
 892                if (meson_mmc_bounce_buf_read(data) ||
 893                    meson_mmc_get_next_command(cmd))
 894                        ret = IRQ_WAKE_THREAD;
 895                else
 896                        ret = IRQ_HANDLED;
 897        }
 898
 899out:
 900        if (cmd->error) {
 901                /* Stop desc in case of errors */
 902                u32 start = readl(host->regs + SD_EMMC_START);
 903
 904                start &= ~START_DESC_BUSY;
 905                writel(start, host->regs + SD_EMMC_START);
 906        }
 907
 908        if (ret == IRQ_HANDLED)
 909                meson_mmc_request_done(host->mmc, cmd->mrq);
 910
 911        return ret;
 912}
 913
 914static int meson_mmc_wait_desc_stop(struct meson_host *host)
 915{
 916        u32 status;
 917
 918        /*
 919         * It may sometimes take a while for it to actually halt. Here, we
 920         * are giving it 5ms to comply
 921         *
 922         * If we don't confirm the descriptor is stopped, it might raise new
 923         * IRQs after we have called mmc_request_done() which is bad.
 924         */
 925
 926        return readl_poll_timeout(host->regs + SD_EMMC_STATUS, status,
 927                                  !(status & (STATUS_BUSY | STATUS_DESC_BUSY)),
 928                                  100, 5000);
 929}
 930
 931static irqreturn_t meson_mmc_irq_thread(int irq, void *dev_id)
 932{
 933        struct meson_host *host = dev_id;
 934        struct mmc_command *next_cmd, *cmd = host->cmd;
 935        struct mmc_data *data;
 936        unsigned int xfer_bytes;
 937
 938        if (WARN_ON(!cmd))
 939                return IRQ_NONE;
 940
 941        if (cmd->error) {
 942                meson_mmc_wait_desc_stop(host);
 943                meson_mmc_request_done(host->mmc, cmd->mrq);
 944
 945                return IRQ_HANDLED;
 946        }
 947
 948        data = cmd->data;
 949        if (meson_mmc_bounce_buf_read(data)) {
 950                xfer_bytes = data->blksz * data->blocks;
 951                WARN_ON(xfer_bytes > host->bounce_buf_size);
 952                sg_copy_from_buffer(data->sg, data->sg_len,
 953                                    host->bounce_buf, xfer_bytes);
 954        }
 955
 956        next_cmd = meson_mmc_get_next_command(cmd);
 957        if (next_cmd)
 958                meson_mmc_start_cmd(host->mmc, next_cmd);
 959        else
 960                meson_mmc_request_done(host->mmc, cmd->mrq);
 961
 962        return IRQ_HANDLED;
 963}
 964
 965/*
 966 * NOTE: we only need this until the GPIO/pinctrl driver can handle
 967 * interrupts.  For now, the MMC core will use this for polling.
 968 */
 969static int meson_mmc_get_cd(struct mmc_host *mmc)
 970{
 971        int status = mmc_gpio_get_cd(mmc);
 972
 973        if (status == -ENOSYS)
 974                return 1; /* assume present */
 975
 976        return status;
 977}
 978
 979static void meson_mmc_cfg_init(struct meson_host *host)
 980{
 981        u32 cfg = 0;
 982
 983        cfg |= FIELD_PREP(CFG_RESP_TIMEOUT_MASK,
 984                          ilog2(SD_EMMC_CFG_RESP_TIMEOUT));
 985        cfg |= FIELD_PREP(CFG_RC_CC_MASK, ilog2(SD_EMMC_CFG_CMD_GAP));
 986        cfg |= FIELD_PREP(CFG_BLK_LEN_MASK, ilog2(SD_EMMC_CFG_BLK_SIZE));
 987
 988        /* abort chain on R/W errors */
 989        cfg |= CFG_ERR_ABORT;
 990
 991        writel(cfg, host->regs + SD_EMMC_CFG);
 992}
 993
 994static int meson_mmc_card_busy(struct mmc_host *mmc)
 995{
 996        struct meson_host *host = mmc_priv(mmc);
 997        u32 regval;
 998
 999        regval = readl(host->regs + SD_EMMC_STATUS);
1000
1001        /* We are only interrested in lines 0 to 3, so mask the other ones */
1002        return !(FIELD_GET(STATUS_DATI, regval) & 0xf);
1003}
1004
1005static int meson_mmc_voltage_switch(struct mmc_host *mmc, struct mmc_ios *ios)
1006{
1007        int ret;
1008
1009        /* vqmmc regulator is available */
1010        if (!IS_ERR(mmc->supply.vqmmc)) {
1011                /*
1012                 * The usual amlogic setup uses a GPIO to switch from one
1013                 * regulator to the other. While the voltage ramp up is
1014                 * pretty fast, care must be taken when switching from 3.3v
1015                 * to 1.8v. Please make sure the regulator framework is aware
1016                 * of your own regulator constraints
1017                 */
1018                ret = mmc_regulator_set_vqmmc(mmc, ios);
1019                return ret < 0 ? ret : 0;
1020        }
1021
1022        /* no vqmmc regulator, assume fixed regulator at 3/3.3V */
1023        if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330)
1024                return 0;
1025
1026        return -EINVAL;
1027}
1028
1029static const struct mmc_host_ops meson_mmc_ops = {
1030        .request        = meson_mmc_request,
1031        .set_ios        = meson_mmc_set_ios,
1032        .get_cd         = meson_mmc_get_cd,
1033        .pre_req        = meson_mmc_pre_req,
1034        .post_req       = meson_mmc_post_req,
1035        .execute_tuning = meson_mmc_resampling_tuning,
1036        .card_busy      = meson_mmc_card_busy,
1037        .start_signal_voltage_switch = meson_mmc_voltage_switch,
1038};
1039
1040static int meson_mmc_probe(struct platform_device *pdev)
1041{
1042        struct resource *res;
1043        struct meson_host *host;
1044        struct mmc_host *mmc;
1045        int ret;
1046
1047        mmc = mmc_alloc_host(sizeof(struct meson_host), &pdev->dev);
1048        if (!mmc)
1049                return -ENOMEM;
1050        host = mmc_priv(mmc);
1051        host->mmc = mmc;
1052        host->dev = &pdev->dev;
1053        dev_set_drvdata(&pdev->dev, host);
1054
1055        /* The G12A SDIO Controller needs an SRAM bounce buffer */
1056        host->dram_access_quirk = device_property_read_bool(&pdev->dev,
1057                                        "amlogic,dram-access-quirk");
1058
1059        /* Get regulators and the supported OCR mask */
1060        host->vqmmc_enabled = false;
1061        ret = mmc_regulator_get_supply(mmc);
1062        if (ret)
1063                goto free_host;
1064
1065        ret = mmc_of_parse(mmc);
1066        if (ret) {
1067                if (ret != -EPROBE_DEFER)
1068                        dev_warn(&pdev->dev, "error parsing DT: %d\n", ret);
1069                goto free_host;
1070        }
1071
1072        host->data = (struct meson_mmc_data *)
1073                of_device_get_match_data(&pdev->dev);
1074        if (!host->data) {
1075                ret = -EINVAL;
1076                goto free_host;
1077        }
1078
1079        ret = device_reset_optional(&pdev->dev);
1080        if (ret) {
1081                if (ret != -EPROBE_DEFER)
1082                        dev_err(&pdev->dev, "device reset failed: %d\n", ret);
1083
1084                return ret;
1085        }
1086
1087        res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1088        host->regs = devm_ioremap_resource(&pdev->dev, res);
1089        if (IS_ERR(host->regs)) {
1090                ret = PTR_ERR(host->regs);
1091                goto free_host;
1092        }
1093
1094        host->irq = platform_get_irq(pdev, 0);
1095        if (host->irq <= 0) {
1096                ret = -EINVAL;
1097                goto free_host;
1098        }
1099
1100        host->pinctrl = devm_pinctrl_get(&pdev->dev);
1101        if (IS_ERR(host->pinctrl)) {
1102                ret = PTR_ERR(host->pinctrl);
1103                goto free_host;
1104        }
1105
1106        host->pins_clk_gate = pinctrl_lookup_state(host->pinctrl,
1107                                                   "clk-gate");
1108        if (IS_ERR(host->pins_clk_gate)) {
1109                dev_warn(&pdev->dev,
1110                         "can't get clk-gate pinctrl, using clk_stop bit\n");
1111                host->pins_clk_gate = NULL;
1112        }
1113
1114        host->core_clk = devm_clk_get(&pdev->dev, "core");
1115        if (IS_ERR(host->core_clk)) {
1116                ret = PTR_ERR(host->core_clk);
1117                goto free_host;
1118        }
1119
1120        ret = clk_prepare_enable(host->core_clk);
1121        if (ret)
1122                goto free_host;
1123
1124        ret = meson_mmc_clk_init(host);
1125        if (ret)
1126                goto err_core_clk;
1127
1128        /* set config to sane default */
1129        meson_mmc_cfg_init(host);
1130
1131        /* Stop execution */
1132        writel(0, host->regs + SD_EMMC_START);
1133
1134        /* clear, ack and enable interrupts */
1135        writel(0, host->regs + SD_EMMC_IRQ_EN);
1136        writel(IRQ_CRC_ERR | IRQ_TIMEOUTS | IRQ_END_OF_CHAIN,
1137               host->regs + SD_EMMC_STATUS);
1138        writel(IRQ_CRC_ERR | IRQ_TIMEOUTS | IRQ_END_OF_CHAIN,
1139               host->regs + SD_EMMC_IRQ_EN);
1140
1141        ret = request_threaded_irq(host->irq, meson_mmc_irq,
1142                                   meson_mmc_irq_thread, IRQF_ONESHOT,
1143                                   dev_name(&pdev->dev), host);
1144        if (ret)
1145                goto err_init_clk;
1146
1147        mmc->caps |= MMC_CAP_CMD23;
1148        if (host->dram_access_quirk) {
1149                /* Limit segments to 1 due to low available sram memory */
1150                mmc->max_segs = 1;
1151                /* Limit to the available sram memory */
1152                mmc->max_blk_count = SD_EMMC_SRAM_DATA_BUF_LEN /
1153                                     mmc->max_blk_size;
1154        } else {
1155                mmc->max_blk_count = CMD_CFG_LENGTH_MASK;
1156                mmc->max_segs = SD_EMMC_DESC_BUF_LEN /
1157                                sizeof(struct sd_emmc_desc);
1158        }
1159        mmc->max_req_size = mmc->max_blk_count * mmc->max_blk_size;
1160        mmc->max_seg_size = mmc->max_req_size;
1161
1162        /*
1163         * At the moment, we don't know how to reliably enable HS400.
1164         * From the different datasheets, it is not even clear if this mode
1165         * is officially supported by any of the SoCs
1166         */
1167        mmc->caps2 &= ~MMC_CAP2_HS400;
1168
1169        if (host->dram_access_quirk) {
1170                /*
1171                 * The MMC Controller embeds 1,5KiB of internal SRAM
1172                 * that can be used to be used as bounce buffer.
1173                 * In the case of the G12A SDIO controller, use these
1174                 * instead of the DDR memory
1175                 */
1176                host->bounce_buf_size = SD_EMMC_SRAM_DATA_BUF_LEN;
1177                host->bounce_buf = host->regs + SD_EMMC_SRAM_DATA_BUF_OFF;
1178                host->bounce_dma_addr = res->start + SD_EMMC_SRAM_DATA_BUF_OFF;
1179        } else {
1180                /* data bounce buffer */
1181                host->bounce_buf_size = mmc->max_req_size;
1182                host->bounce_buf =
1183                        dma_alloc_coherent(host->dev, host->bounce_buf_size,
1184                                           &host->bounce_dma_addr, GFP_KERNEL);
1185                if (host->bounce_buf == NULL) {
1186                        dev_err(host->dev, "Unable to map allocate DMA bounce buffer.\n");
1187                        ret = -ENOMEM;
1188                        goto err_free_irq;
1189                }
1190        }
1191
1192        host->descs = dma_alloc_coherent(host->dev, SD_EMMC_DESC_BUF_LEN,
1193                      &host->descs_dma_addr, GFP_KERNEL);
1194        if (!host->descs) {
1195                dev_err(host->dev, "Allocating descriptor DMA buffer failed\n");
1196                ret = -ENOMEM;
1197                goto err_bounce_buf;
1198        }
1199
1200        mmc->ops = &meson_mmc_ops;
1201        mmc_add_host(mmc);
1202
1203        return 0;
1204
1205err_bounce_buf:
1206        if (!host->dram_access_quirk)
1207                dma_free_coherent(host->dev, host->bounce_buf_size,
1208                                  host->bounce_buf, host->bounce_dma_addr);
1209err_free_irq:
1210        free_irq(host->irq, host);
1211err_init_clk:
1212        clk_disable_unprepare(host->mmc_clk);
1213err_core_clk:
1214        clk_disable_unprepare(host->core_clk);
1215free_host:
1216        mmc_free_host(mmc);
1217        return ret;
1218}
1219
1220static int meson_mmc_remove(struct platform_device *pdev)
1221{
1222        struct meson_host *host = dev_get_drvdata(&pdev->dev);
1223
1224        mmc_remove_host(host->mmc);
1225
1226        /* disable interrupts */
1227        writel(0, host->regs + SD_EMMC_IRQ_EN);
1228        free_irq(host->irq, host);
1229
1230        dma_free_coherent(host->dev, SD_EMMC_DESC_BUF_LEN,
1231                          host->descs, host->descs_dma_addr);
1232
1233        if (!host->dram_access_quirk)
1234                dma_free_coherent(host->dev, host->bounce_buf_size,
1235                                  host->bounce_buf, host->bounce_dma_addr);
1236
1237        clk_disable_unprepare(host->mmc_clk);
1238        clk_disable_unprepare(host->core_clk);
1239
1240        mmc_free_host(host->mmc);
1241        return 0;
1242}
1243
1244static const struct meson_mmc_data meson_gx_data = {
1245        .tx_delay_mask  = CLK_V2_TX_DELAY_MASK,
1246        .rx_delay_mask  = CLK_V2_RX_DELAY_MASK,
1247        .always_on      = CLK_V2_ALWAYS_ON,
1248        .adjust         = SD_EMMC_ADJUST,
1249};
1250
1251static const struct meson_mmc_data meson_axg_data = {
1252        .tx_delay_mask  = CLK_V3_TX_DELAY_MASK,
1253        .rx_delay_mask  = CLK_V3_RX_DELAY_MASK,
1254        .always_on      = CLK_V3_ALWAYS_ON,
1255        .adjust         = SD_EMMC_V3_ADJUST,
1256};
1257
1258static const struct of_device_id meson_mmc_of_match[] = {
1259        { .compatible = "amlogic,meson-gx-mmc",         .data = &meson_gx_data },
1260        { .compatible = "amlogic,meson-gxbb-mmc",       .data = &meson_gx_data },
1261        { .compatible = "amlogic,meson-gxl-mmc",        .data = &meson_gx_data },
1262        { .compatible = "amlogic,meson-gxm-mmc",        .data = &meson_gx_data },
1263        { .compatible = "amlogic,meson-axg-mmc",        .data = &meson_axg_data },
1264        {}
1265};
1266MODULE_DEVICE_TABLE(of, meson_mmc_of_match);
1267
1268static struct platform_driver meson_mmc_driver = {
1269        .probe          = meson_mmc_probe,
1270        .remove         = meson_mmc_remove,
1271        .driver         = {
1272                .name = DRIVER_NAME,
1273                .of_match_table = of_match_ptr(meson_mmc_of_match),
1274        },
1275};
1276
1277module_platform_driver(meson_mmc_driver);
1278
1279MODULE_DESCRIPTION("Amlogic S905*/GX*/AXG SD/eMMC driver");
1280MODULE_AUTHOR("Kevin Hilman <khilman@baylibre.com>");
1281MODULE_LICENSE("GPL v2");
1282