1
2
3
4
5
6
7
8
9
10#include <linux/gpio.h>
11#include <linux/module.h>
12#include <linux/kernel.h>
13#include <linux/init.h>
14#include <linux/irq.h>
15#include <linux/delay.h>
16#include <linux/serial.h>
17#include <linux/tty.h>
18#include <linux/serial_8250.h>
19#include <linux/serial_reg.h>
20#include <linux/clk.h>
21#include <linux/io.h>
22
23#include <asm/mach-types.h>
24
25#include <mach/mux.h>
26
27#include "pm.h"
28#include "soc.h"
29
30static struct clk * uart1_ck;
31static struct clk * uart2_ck;
32static struct clk * uart3_ck;
33
34static inline unsigned int omap_serial_in(struct plat_serial8250_port *up,
35 int offset)
36{
37 offset <<= up->regshift;
38 return (unsigned int)__raw_readb(up->membase + offset);
39}
40
41static inline void omap_serial_outp(struct plat_serial8250_port *p, int offset,
42 int value)
43{
44 offset <<= p->regshift;
45 __raw_writeb(value, p->membase + offset);
46}
47
48
49
50
51
52
53static void __init omap_serial_reset(struct plat_serial8250_port *p)
54{
55 omap_serial_outp(p, UART_OMAP_MDR1,
56 UART_OMAP_MDR1_DISABLE);
57 omap_serial_outp(p, UART_OMAP_SCR, 0x08);
58 omap_serial_outp(p, UART_OMAP_MDR1,
59 UART_OMAP_MDR1_16X_MODE);
60
61 if (!cpu_is_omap15xx()) {
62 omap_serial_outp(p, UART_OMAP_SYSC, 0x01);
63 while (!(omap_serial_in(p, UART_OMAP_SYSC) & 0x01));
64 }
65}
66
67static struct plat_serial8250_port serial_platform_data[] = {
68 {
69 .mapbase = OMAP1_UART1_BASE,
70 .irq = INT_UART1,
71 .flags = UPF_BOOT_AUTOCONF,
72 .iotype = UPIO_MEM,
73 .regshift = 2,
74 .uartclk = OMAP16XX_BASE_BAUD * 16,
75 },
76 {
77 .mapbase = OMAP1_UART2_BASE,
78 .irq = INT_UART2,
79 .flags = UPF_BOOT_AUTOCONF,
80 .iotype = UPIO_MEM,
81 .regshift = 2,
82 .uartclk = OMAP16XX_BASE_BAUD * 16,
83 },
84 {
85 .mapbase = OMAP1_UART3_BASE,
86 .irq = INT_UART3,
87 .flags = UPF_BOOT_AUTOCONF,
88 .iotype = UPIO_MEM,
89 .regshift = 2,
90 .uartclk = OMAP16XX_BASE_BAUD * 16,
91 },
92 { },
93};
94
95static struct platform_device serial_device = {
96 .name = "serial8250",
97 .id = PLAT8250_DEV_PLATFORM,
98 .dev = {
99 .platform_data = serial_platform_data,
100 },
101};
102
103
104
105
106
107
108void __init omap_serial_init(void)
109{
110 int i;
111
112 if (cpu_is_omap7xx()) {
113 serial_platform_data[0].regshift = 0;
114 serial_platform_data[1].regshift = 0;
115 serial_platform_data[0].irq = INT_7XX_UART_MODEM_1;
116 serial_platform_data[1].irq = INT_7XX_UART_MODEM_IRDA_2;
117 }
118
119 if (cpu_is_omap15xx()) {
120 serial_platform_data[0].uartclk = OMAP1510_BASE_BAUD * 16;
121 serial_platform_data[1].uartclk = OMAP1510_BASE_BAUD * 16;
122 serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16;
123 }
124
125 for (i = 0; i < ARRAY_SIZE(serial_platform_data) - 1; i++) {
126
127
128 if (cpu_is_omap7xx() && i > 1) {
129 serial_platform_data[i].membase = NULL;
130 serial_platform_data[i].mapbase = 0;
131 continue;
132 }
133
134
135 serial_platform_data[i].membase =
136 ioremap(serial_platform_data[i].mapbase, SZ_2K);
137 if (!serial_platform_data[i].membase) {
138 printk(KERN_ERR "Could not ioremap uart%i\n", i);
139 continue;
140 }
141 switch (i) {
142 case 0:
143 uart1_ck = clk_get(NULL, "uart1_ck");
144 if (IS_ERR(uart1_ck))
145 printk("Could not get uart1_ck\n");
146 else {
147 clk_enable(uart1_ck);
148 if (cpu_is_omap15xx())
149 clk_set_rate(uart1_ck, 12000000);
150 }
151 break;
152 case 1:
153 uart2_ck = clk_get(NULL, "uart2_ck");
154 if (IS_ERR(uart2_ck))
155 printk("Could not get uart2_ck\n");
156 else {
157 clk_enable(uart2_ck);
158 if (cpu_is_omap15xx())
159 clk_set_rate(uart2_ck, 12000000);
160 else
161 clk_set_rate(uart2_ck, 48000000);
162 }
163 break;
164 case 2:
165 uart3_ck = clk_get(NULL, "uart3_ck");
166 if (IS_ERR(uart3_ck))
167 printk("Could not get uart3_ck\n");
168 else {
169 clk_enable(uart3_ck);
170 if (cpu_is_omap15xx())
171 clk_set_rate(uart3_ck, 12000000);
172 }
173 break;
174 }
175 omap_serial_reset(&serial_platform_data[i]);
176 }
177}
178
179#ifdef CONFIG_OMAP_SERIAL_WAKE
180
181static irqreturn_t omap_serial_wake_interrupt(int irq, void *dev_id)
182{
183
184 return IRQ_HANDLED;
185}
186
187
188
189
190
191
192void omap_serial_wake_trigger(int enable)
193{
194 if (!cpu_is_omap16xx())
195 return;
196
197 if (uart1_ck != NULL) {
198 if (enable)
199 omap_cfg_reg(V14_16XX_GPIO37);
200 else
201 omap_cfg_reg(V14_16XX_UART1_RX);
202 }
203 if (uart2_ck != NULL) {
204 if (enable)
205 omap_cfg_reg(R9_16XX_GPIO18);
206 else
207 omap_cfg_reg(R9_16XX_UART2_RX);
208 }
209 if (uart3_ck != NULL) {
210 if (enable)
211 omap_cfg_reg(L14_16XX_GPIO49);
212 else
213 omap_cfg_reg(L14_16XX_UART3_RX);
214 }
215}
216
217static void __init omap_serial_set_port_wakeup(int gpio_nr)
218{
219 int ret;
220
221 ret = gpio_request(gpio_nr, "UART wake");
222 if (ret < 0) {
223 printk(KERN_ERR "Could not request UART wake GPIO: %i\n",
224 gpio_nr);
225 return;
226 }
227 gpio_direction_input(gpio_nr);
228 ret = request_irq(gpio_to_irq(gpio_nr), &omap_serial_wake_interrupt,
229 IRQF_TRIGGER_RISING, "serial wakeup", NULL);
230 if (ret) {
231 gpio_free(gpio_nr);
232 printk(KERN_ERR "No interrupt for UART wake GPIO: %i\n",
233 gpio_nr);
234 return;
235 }
236 enable_irq_wake(gpio_to_irq(gpio_nr));
237}
238
239int __init omap_serial_wakeup_init(void)
240{
241 if (!cpu_is_omap16xx())
242 return 0;
243
244 if (uart1_ck != NULL)
245 omap_serial_set_port_wakeup(37);
246 if (uart2_ck != NULL)
247 omap_serial_set_port_wakeup(18);
248 if (uart3_ck != NULL)
249 omap_serial_set_port_wakeup(49);
250
251 return 0;
252}
253
254#endif
255
256static int __init omap_init(void)
257{
258 if (!cpu_class_is_omap1())
259 return -ENODEV;
260
261 return platform_device_register(&serial_device);
262}
263arch_initcall(omap_init);
264
