linux/arch/arm/mach-pxa/am200epd.c
<<
>>
Prefs
   1/*
   2 * am200epd.c -- Platform device for AM200 EPD kit
   3 *
   4 * Copyright (C) 2008, Jaya Kumar
   5 *
   6 * This file is subject to the terms and conditions of the GNU General Public
   7 * License. See the file COPYING in the main directory of this archive for
   8 * more details.
   9 *
  10 * Layout is based on skeletonfb.c by James Simmons and Geert Uytterhoeven.
  11 *
  12 * This work was made possible by help and equipment support from E-Ink
  13 * Corporation. http://support.eink.com/community
  14 *
  15 * This driver is written to be used with the Metronome display controller.
  16 * on the AM200 EPD prototype kit/development kit with an E-Ink 800x600
  17 * Vizplex EPD on a Gumstix board using the Lyre interface board.
  18 *
  19 */
  20
  21#include <linux/module.h>
  22#include <linux/kernel.h>
  23#include <linux/errno.h>
  24#include <linux/string.h>
  25#include <linux/delay.h>
  26#include <linux/interrupt.h>
  27#include <linux/fb.h>
  28#include <linux/init.h>
  29#include <linux/platform_device.h>
  30#include <linux/irq.h>
  31#include <linux/gpio.h>
  32
  33#include "pxa25x.h"
  34#include "gumstix.h"
  35#include <linux/platform_data/video-pxafb.h>
  36
  37#include "generic.h"
  38
  39#include <video/metronomefb.h>
  40
  41static unsigned int panel_type = 6;
  42static struct platform_device *am200_device;
  43static struct metronome_board am200_board;
  44
  45static struct pxafb_mode_info am200_fb_mode_9inch7 = {
  46        .pixclock       = 40000,
  47        .xres           = 1200,
  48        .yres           = 842,
  49        .bpp            = 16,
  50        .hsync_len      = 2,
  51        .left_margin    = 2,
  52        .right_margin   = 2,
  53        .vsync_len      = 1,
  54        .upper_margin   = 2,
  55        .lower_margin   = 25,
  56        .sync           = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
  57};
  58
  59static struct pxafb_mode_info am200_fb_mode_8inch = {
  60        .pixclock       = 40000,
  61        .xres           = 1088,
  62        .yres           = 791,
  63        .bpp            = 16,
  64        .hsync_len      = 28,
  65        .left_margin    = 8,
  66        .right_margin   = 30,
  67        .vsync_len      = 8,
  68        .upper_margin   = 10,
  69        .lower_margin   = 8,
  70        .sync           = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
  71};
  72
  73static struct pxafb_mode_info am200_fb_mode_6inch = {
  74        .pixclock       = 40189,
  75        .xres           = 832,
  76        .yres           = 622,
  77        .bpp            = 16,
  78        .hsync_len      = 28,
  79        .left_margin    = 34,
  80        .right_margin   = 34,
  81        .vsync_len      = 25,
  82        .upper_margin   = 0,
  83        .lower_margin   = 2,
  84        .sync           = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
  85};
  86
  87static struct pxafb_mach_info am200_fb_info = {
  88        .modes          = &am200_fb_mode_6inch,
  89        .num_modes      = 1,
  90        .lcd_conn       = LCD_TYPE_COLOR_TFT | LCD_PCLK_EDGE_FALL |
  91                          LCD_AC_BIAS_FREQ(24),
  92};
  93
  94/* register offsets for gpio control */
  95#define LED_GPIO_PIN 51
  96#define STDBY_GPIO_PIN 48
  97#define RST_GPIO_PIN 49
  98#define RDY_GPIO_PIN 32
  99#define ERR_GPIO_PIN 17
 100#define PCBPWR_GPIO_PIN 16
 101static int gpios[] = { LED_GPIO_PIN , STDBY_GPIO_PIN , RST_GPIO_PIN,
 102                        RDY_GPIO_PIN, ERR_GPIO_PIN, PCBPWR_GPIO_PIN };
 103static char *gpio_names[] = { "LED" , "STDBY" , "RST", "RDY", "ERR", "PCBPWR" };
 104
 105static int am200_init_gpio_regs(struct metronomefb_par *par)
 106{
 107        int i;
 108        int err;
 109
 110        for (i = 0; i < ARRAY_SIZE(gpios); i++) {
 111                err = gpio_request(gpios[i], gpio_names[i]);
 112                if (err) {
 113                        dev_err(&am200_device->dev, "failed requesting "
 114                                "gpio %s, err=%d\n", gpio_names[i], err);
 115                        goto err_req_gpio;
 116                }
 117        }
 118
 119        gpio_direction_output(LED_GPIO_PIN, 0);
 120        gpio_direction_output(STDBY_GPIO_PIN, 0);
 121        gpio_direction_output(RST_GPIO_PIN, 0);
 122
 123        gpio_direction_input(RDY_GPIO_PIN);
 124        gpio_direction_input(ERR_GPIO_PIN);
 125
 126        gpio_direction_output(PCBPWR_GPIO_PIN, 0);
 127
 128        return 0;
 129
 130err_req_gpio:
 131        while (--i >= 0)
 132                gpio_free(gpios[i]);
 133
 134        return err;
 135}
 136
 137static void am200_cleanup(struct metronomefb_par *par)
 138{
 139        int i;
 140
 141        free_irq(PXA_GPIO_TO_IRQ(RDY_GPIO_PIN), par);
 142
 143        for (i = 0; i < ARRAY_SIZE(gpios); i++)
 144                gpio_free(gpios[i]);
 145}
 146
 147static int am200_share_video_mem(struct fb_info *info)
 148{
 149        /* rough check if this is our desired fb and not something else */
 150        if ((info->var.xres != am200_fb_info.modes->xres)
 151                || (info->var.yres != am200_fb_info.modes->yres))
 152                return 0;
 153
 154        /* we've now been notified that we have our new fb */
 155        am200_board.metromem = info->screen_base;
 156        am200_board.host_fbinfo = info;
 157
 158        /* try to refcount host drv since we are the consumer after this */
 159        if (!try_module_get(info->fbops->owner))
 160                return -ENODEV;
 161
 162        return 0;
 163}
 164
 165static int am200_unshare_video_mem(struct fb_info *info)
 166{
 167        dev_dbg(&am200_device->dev, "ENTER %s\n", __func__);
 168
 169        if (info != am200_board.host_fbinfo)
 170                return 0;
 171
 172        module_put(am200_board.host_fbinfo->fbops->owner);
 173        return 0;
 174}
 175
 176static int am200_fb_notifier_callback(struct notifier_block *self,
 177                                 unsigned long event, void *data)
 178{
 179        struct fb_event *evdata = data;
 180        struct fb_info *info = evdata->info;
 181
 182        dev_dbg(&am200_device->dev, "ENTER %s\n", __func__);
 183
 184        if (event == FB_EVENT_FB_REGISTERED)
 185                return am200_share_video_mem(info);
 186        else if (event == FB_EVENT_FB_UNREGISTERED)
 187                return am200_unshare_video_mem(info);
 188
 189        return 0;
 190}
 191
 192static struct notifier_block am200_fb_notif = {
 193        .notifier_call = am200_fb_notifier_callback,
 194};
 195
 196/* this gets called as part of our init. these steps must be done now so
 197 * that we can use pxa_set_fb_info */
 198static void __init am200_presetup_fb(void)
 199{
 200        int fw;
 201        int fh;
 202        int padding_size;
 203        int totalsize;
 204
 205        switch (panel_type) {
 206        case 6:
 207                am200_fb_info.modes = &am200_fb_mode_6inch;
 208                break;
 209        case 8:
 210                am200_fb_info.modes = &am200_fb_mode_8inch;
 211                break;
 212        case 97:
 213                am200_fb_info.modes = &am200_fb_mode_9inch7;
 214                break;
 215        default:
 216                dev_err(&am200_device->dev, "invalid panel_type selection,"
 217                                                " setting to 6\n");
 218                am200_fb_info.modes = &am200_fb_mode_6inch;
 219                break;
 220        }
 221
 222        /* the frame buffer is divided as follows:
 223        command | CRC | padding
 224        16kb waveform data | CRC | padding
 225        image data | CRC
 226        */
 227
 228        fw = am200_fb_info.modes->xres;
 229        fh = am200_fb_info.modes->yres;
 230
 231        /* waveform must be 16k + 2 for checksum */
 232        am200_board.wfm_size = roundup(16*1024 + 2, fw);
 233
 234        padding_size = PAGE_SIZE + (4 * fw);
 235
 236        /* total is 1 cmd , 1 wfm, padding and image */
 237        totalsize = fw + am200_board.wfm_size + padding_size + (fw*fh);
 238
 239        /* save this off because we're manipulating fw after this and
 240         * we'll need it when we're ready to setup the framebuffer */
 241        am200_board.fw = fw;
 242        am200_board.fh = fh;
 243
 244        /* the reason we do this adjustment is because we want to acquire
 245         * more framebuffer memory without imposing custom awareness on the
 246         * underlying pxafb driver */
 247        am200_fb_info.modes->yres = DIV_ROUND_UP(totalsize, fw);
 248
 249        /* we divide since we told the LCD controller we're 16bpp */
 250        am200_fb_info.modes->xres /= 2;
 251
 252        pxa_set_fb_info(NULL, &am200_fb_info);
 253
 254}
 255
 256/* this gets called by metronomefb as part of its init, in our case, we
 257 * have already completed initial framebuffer init in presetup_fb so we
 258 * can just setup the fb access pointers */
 259static int am200_setup_fb(struct metronomefb_par *par)
 260{
 261        int fw;
 262        int fh;
 263
 264        fw = am200_board.fw;
 265        fh = am200_board.fh;
 266
 267        /* metromem was set up by the notifier in share_video_mem so now
 268         * we can use its value to calculate the other entries */
 269        par->metromem_cmd = (struct metromem_cmd *) am200_board.metromem;
 270        par->metromem_wfm = am200_board.metromem + fw;
 271        par->metromem_img = par->metromem_wfm + am200_board.wfm_size;
 272        par->metromem_img_csum = (u16 *) (par->metromem_img + (fw * fh));
 273        par->metromem_dma = am200_board.host_fbinfo->fix.smem_start;
 274
 275        return 0;
 276}
 277
 278static int am200_get_panel_type(void)
 279{
 280        return panel_type;
 281}
 282
 283static irqreturn_t am200_handle_irq(int irq, void *dev_id)
 284{
 285        struct metronomefb_par *par = dev_id;
 286
 287        wake_up_interruptible(&par->waitq);
 288        return IRQ_HANDLED;
 289}
 290
 291static int am200_setup_irq(struct fb_info *info)
 292{
 293        int ret;
 294
 295        ret = request_irq(PXA_GPIO_TO_IRQ(RDY_GPIO_PIN), am200_handle_irq,
 296                                IRQF_TRIGGER_FALLING, "AM200", info->par);
 297        if (ret)
 298                dev_err(&am200_device->dev, "request_irq failed: %d\n", ret);
 299
 300        return ret;
 301}
 302
 303static void am200_set_rst(struct metronomefb_par *par, int state)
 304{
 305        gpio_set_value(RST_GPIO_PIN, state);
 306}
 307
 308static void am200_set_stdby(struct metronomefb_par *par, int state)
 309{
 310        gpio_set_value(STDBY_GPIO_PIN, state);
 311}
 312
 313static int am200_wait_event(struct metronomefb_par *par)
 314{
 315        return wait_event_timeout(par->waitq, gpio_get_value(RDY_GPIO_PIN), HZ);
 316}
 317
 318static int am200_wait_event_intr(struct metronomefb_par *par)
 319{
 320        return wait_event_interruptible_timeout(par->waitq,
 321                                        gpio_get_value(RDY_GPIO_PIN), HZ);
 322}
 323
 324static struct metronome_board am200_board = {
 325        .owner                  = THIS_MODULE,
 326        .setup_irq              = am200_setup_irq,
 327        .setup_io               = am200_init_gpio_regs,
 328        .setup_fb               = am200_setup_fb,
 329        .set_rst                = am200_set_rst,
 330        .set_stdby              = am200_set_stdby,
 331        .met_wait_event         = am200_wait_event,
 332        .met_wait_event_intr    = am200_wait_event_intr,
 333        .get_panel_type         = am200_get_panel_type,
 334        .cleanup                = am200_cleanup,
 335};
 336
 337static unsigned long am200_pin_config[] __initdata = {
 338        GPIO51_GPIO,
 339        GPIO49_GPIO,
 340        GPIO48_GPIO,
 341        GPIO32_GPIO,
 342        GPIO17_GPIO,
 343        GPIO16_GPIO,
 344};
 345
 346int __init am200_init(void)
 347{
 348        int ret;
 349
 350        /* before anything else, we request notification for any fb
 351         * creation events */
 352        fb_register_client(&am200_fb_notif);
 353
 354        pxa2xx_mfp_config(ARRAY_AND_SIZE(am200_pin_config));
 355
 356        /* request our platform independent driver */
 357        request_module("metronomefb");
 358
 359        am200_device = platform_device_alloc("metronomefb", -1);
 360        if (!am200_device)
 361                return -ENOMEM;
 362
 363        /* the am200_board that will be seen by metronomefb is a copy */
 364        platform_device_add_data(am200_device, &am200_board,
 365                                        sizeof(am200_board));
 366
 367        /* this _add binds metronomefb to am200. metronomefb refcounts am200 */
 368        ret = platform_device_add(am200_device);
 369
 370        if (ret) {
 371                platform_device_put(am200_device);
 372                fb_unregister_client(&am200_fb_notif);
 373                return ret;
 374        }
 375
 376        am200_presetup_fb();
 377
 378        return 0;
 379}
 380
 381module_param(panel_type, uint, 0);
 382MODULE_PARM_DESC(panel_type, "Select the panel type: 6, 8, 97");
 383
 384MODULE_DESCRIPTION("board driver for am200 metronome epd kit");
 385MODULE_AUTHOR("Jaya Kumar");
 386MODULE_LICENSE("GPL");
 387