/*
 *    pata_radisys.c - Intel PATA/SATA controllers
 *
 *      (C) 2006 Red Hat <alan@lxorguk.ukuu.org.uk>
 *
 *    Some parts based on ata_piix.c by Jeff Garzik and others.
 *
 *    A PIIX relative, this device has a single ATA channel and no
 *    slave timings, SITRE or PPE. In that sense it is a close relative
 *    of the original PIIX. It does however support UDMA 33/66 per channel
 *    although no other modes/timings. Also lacking is 32bit I/O on the ATA
 *    port.
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <linux/ata.h>

#define DRV_NAME        "pata_radisys"
#define DRV_VERSION     "0.4.4"

/**
 *      radisys_set_piomode - Initialize host controller PATA PIO timings
 *      @ap: ATA port
 *      @adev: Device whose timings we are configuring
 *
 *      Set PIO mode for device, in host controller PCI config space.
 *
 *      LOCKING:
 *      None (inherited from caller).
 */

static void radisys_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
        unsigned int pio        = adev->pio_mode - XFER_PIO_0;
        struct pci_dev *dev     = to_pci_dev(ap->host->dev);
        u16 idetm_data;
        int control = 0;

        /*
         *      See Intel Document 298600-004 for the timing programing rules
         *      for PIIX/ICH. Note that the early PIIX does not have the slave
         *      timing port at 0x44. The Radisys is a relative of the PIIX
         *      but not the same so be careful.
         */

        static const     /* ISP  RTC */
        u8 timings[][2] = { { 0, 0 },   /* Check me */
                            { 0, 0 },
                            { 1, 1 },
                            { 2, 2 },
                            { 3, 3 }, };

        if (pio > 0)
                control |= 1;   /* TIME1 enable */
        if (ata_pio_need_iordy(adev))
                control |= 2;   /* IE IORDY */

        pci_read_config_word(dev, 0x40, &idetm_data);

        /* Enable IE and TIME as appropriate. Clear the other
           drive timing bits */
        idetm_data &= 0xCCCC;
        idetm_data |= (control << (4 * adev->devno));
        idetm_data |= (timings[pio][0] << 12) |
                        (timings[pio][1] << 8);
        pci_write_config_word(dev, 0x40, idetm_data);

        /* Track which port is configured */
        ap->private_data = adev;
}

/**
 *      radisys_set_dmamode - Initialize host controller PATA DMA timings
 *      @ap: Port whose timings we are configuring
 *      @adev: Device to program
 *
 *      Set MWDMA mode for device, in host controller PCI config space.
 *
 *      LOCKING:
 *      None (inherited from caller).
 */

static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
        struct pci_dev *dev     = to_pci_dev(ap->host->dev);
        u16 idetm_data;
        u8 udma_enable;

        static const     /* ISP  RTC */
        u8 timings[][2] = { { 0, 0 },
                            { 0, 0 },
                            { 1, 1 },
                            { 2, 2 },
                            { 3, 3 }, };

        /*
         * MWDMA is driven by the PIO timings. We must also enable
         * IORDY unconditionally.
         */

        pci_read_config_word(dev, 0x40, &idetm_data);
        pci_read_config_byte(dev, 0x48, &udma_enable);

        if (adev->dma_mode < XFER_UDMA_0) {
                unsigned int mwdma      = adev->dma_mode - XFER_MW_DMA_0;
                const unsigned int needed_pio[3] = {
                        XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
                };
                int pio = needed_pio[mwdma] - XFER_PIO_0;
                int control = 3;        /* IORDY|TIME0 */

                /* If the drive MWDMA is faster than it can do PIO then
                   we must force PIO0 for PIO cycles. */

                if (adev->pio_mode < needed_pio[mwdma])
                        control = 1;

                /* Mask out the relevant control and timing bits we will load. Also
                   clear the other drive TIME register as a precaution */

                idetm_data &= 0xCCCC;
                idetm_data |= control << (4 * adev->devno);
                idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);

                udma_enable &= ~(1 << adev->devno);
        } else {
                u8 udma_mode;

                /* UDMA66 on: UDMA 33 and 66 are switchable via register 0x4A */

                pci_read_config_byte(dev, 0x4A, &udma_mode);

                if (adev->xfer_mode == XFER_UDMA_2)
                        udma_mode &= ~(2 << (adev->devno * 4));
                else /* UDMA 4 */
                        udma_mode |= (2 << (adev->devno * 4));

                pci_write_config_byte(dev, 0x4A, udma_mode);

                udma_enable |= (1 << adev->devno);
        }
        pci_write_config_word(dev, 0x40, idetm_data);
        pci_write_config_byte(dev, 0x48, udma_enable);

        /* Track which port is configured */
        ap->private_data = adev;
}

/**
 *      radisys_qc_issue        -       command issue
 *      @qc: command pending
 *
 *      Called when the libata layer is about to issue a command. We wrap
 *      this interface so that we can load the correct ATA timings if
 *      necessary. Our logic also clears TIME0/TIME1 for the other device so
 *      that, even if we get this wrong, cycles to the other device will
 *      be made PIO0.
 */

static unsigned int radisys_qc_issue(struct ata_queued_cmd *qc)
{
        struct ata_port *ap = qc->ap;
        struct ata_device *adev = qc->dev;

        if (adev != ap->private_data) {
                /* UDMA timing is not shared */
                if (adev->dma_mode < XFER_UDMA_0) {
                        if (adev->dma_mode)
                                radisys_set_dmamode(ap, adev);
                        else if (adev->pio_mode)
                                radisys_set_piomode(ap, adev);
                }
        }
        return ata_bmdma_qc_issue(qc);
}


static struct scsi_host_template radisys_sht = {
        ATA_BMDMA_SHT(DRV_NAME),
};

static struct ata_port_operations radisys_pata_ops = {
        .inherits               = &ata_bmdma_port_ops,
        .qc_issue               = radisys_qc_issue,
        .cable_detect           = ata_cable_unknown,
        .set_piomode            = radisys_set_piomode,
        .set_dmamode            = radisys_set_dmamode,
};


/**
 *      radisys_init_one - Register PIIX ATA PCI device with kernel services
 *      @pdev: PCI device to register
 *      @ent: Entry in radisys_pci_tbl matching with @pdev
 *
 *      Called from kernel PCI layer.  We probe for combined mode (sigh),
 *      and then hand over control to libata, for it to do the rest.
 *
 *      LOCKING:
 *      Inherited from PCI layer (may sleep).
 *
 *      RETURNS:
 *      Zero on success, or -ERRNO value.
 */

static int radisys_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
        static const struct ata_port_info info = {
                .flags          = ATA_FLAG_SLAVE_POSS,
                .pio_mask       = ATA_PIO4,
                .mwdma_mask     = ATA_MWDMA12_ONLY,
                .udma_mask      = ATA_UDMA24_ONLY,
                .port_ops       = &radisys_pata_ops,
        };
        const struct ata_port_info *ppi[] = { &info, NULL };

        ata_print_version_once(&pdev->dev, DRV_VERSION);

        return ata_pci_bmdma_init_one(pdev, ppi, &radisys_sht, NULL, 0);
}

static const struct pci_device_id radisys_pci_tbl[] = {
        { PCI_VDEVICE(RADISYS, 0x8201), },

        { }     /* terminate list */
};

static struct pci_driver radisys_pci_driver = {
        .name                   = DRV_NAME,
        .id_table               = radisys_pci_tbl,
        .probe                  = radisys_init_one,
        .remove                 = ata_pci_remove_one,
#ifdef CONFIG_PM_SLEEP
        .suspend                = ata_pci_device_suspend,
        .resume                 = ata_pci_device_resume,
#endif
};

module_pci_driver(radisys_pci_driver);

MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for Radisys R82600 controllers");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, radisys_pci_tbl);
MODULE_VERSION(DRV_VERSION);