/*
 * SC16IS7xx tty serial driver - Copyright (C) 2014 GridPoint
 * Author: Jon Ringle <jringle@gridpoint.com>
 *
 *  Based on max310x.c, by Alexander Shiyan <shc_work@mail.ru>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 */

#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

#include <linux/bitops.h>
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/gpio.h>
#include <linux/i2c.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/regmap.h>
#include <linux/serial_core.h>
#include <linux/serial.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/spi/spi.h>
#include <linux/uaccess.h>

#define SC16IS7XX_NAME                  "sc16is7xx"
#define SC16IS7XX_MAX_DEVS              8

/* SC16IS7XX register definitions */
#define SC16IS7XX_RHR_REG               (0x00) /* RX FIFO */
#define SC16IS7XX_THR_REG               (0x00) /* TX FIFO */
#define SC16IS7XX_IER_REG               (0x01) /* Interrupt enable */
#define SC16IS7XX_IIR_REG               (0x02) /* Interrupt Identification */
#define SC16IS7XX_FCR_REG               (0x02) /* FIFO control */
#define SC16IS7XX_LCR_REG               (0x03) /* Line Control */
#define SC16IS7XX_MCR_REG               (0x04) /* Modem Control */
#define SC16IS7XX_LSR_REG               (0x05) /* Line Status */
#define SC16IS7XX_MSR_REG               (0x06) /* Modem Status */
#define SC16IS7XX_SPR_REG               (0x07) /* Scratch Pad */
#define SC16IS7XX_TXLVL_REG             (0x08) /* TX FIFO level */
#define SC16IS7XX_RXLVL_REG             (0x09) /* RX FIFO level */
#define SC16IS7XX_IODIR_REG             (0x0a) /* I/O Direction
                                                * - only on 75x/76x
                                                */
#define SC16IS7XX_IOSTATE_REG           (0x0b) /* I/O State
                                                * - only on 75x/76x
                                                */
#define SC16IS7XX_IOINTENA_REG          (0x0c) /* I/O Interrupt Enable
                                                * - only on 75x/76x
                                                */
#define SC16IS7XX_IOCONTROL_REG         (0x0e) /* I/O Control
                                                * - only on 75x/76x
                                                */
#define SC16IS7XX_EFCR_REG              (0x0f) /* Extra Features Control */

/* TCR/TLR Register set: Only if ((MCR[2] == 1) && (EFR[4] == 1)) */
#define SC16IS7XX_TCR_REG               (0x06) /* Transmit control */
#define SC16IS7XX_TLR_REG               (0x07) /* Trigger level */

/* Special Register set: Only if ((LCR[7] == 1) && (LCR != 0xBF)) */
#define SC16IS7XX_DLL_REG               (0x00) /* Divisor Latch Low */
#define SC16IS7XX_DLH_REG               (0x01) /* Divisor Latch High */

/* Enhanced Register set: Only if (LCR == 0xBF) */
#define SC16IS7XX_EFR_REG               (0x02) /* Enhanced Features */
#define SC16IS7XX_XON1_REG              (0x04) /* Xon1 word */
#define SC16IS7XX_XON2_REG              (0x05) /* Xon2 word */
#define SC16IS7XX_XOFF1_REG             (0x06) /* Xoff1 word */
#define SC16IS7XX_XOFF2_REG             (0x07) /* Xoff2 word */

/* IER register bits */
#define SC16IS7XX_IER_RDI_BIT           (1 << 0) /* Enable RX data interrupt */
#define SC16IS7XX_IER_THRI_BIT          (1 << 1) /* Enable TX holding register
                                                  * interrupt */
#define SC16IS7XX_IER_RLSI_BIT          (1 << 2) /* Enable RX line status
                                                  * interrupt */
#define SC16IS7XX_IER_MSI_BIT           (1 << 3) /* Enable Modem status
                                                  * interrupt */

/* IER register bits - write only if (EFR[4] == 1) */
#define SC16IS7XX_IER_SLEEP_BIT         (1 << 4) /* Enable Sleep mode */
#define SC16IS7XX_IER_XOFFI_BIT         (1 << 5) /* Enable Xoff interrupt */
#define SC16IS7XX_IER_RTSI_BIT          (1 << 6) /* Enable nRTS interrupt */
#define SC16IS7XX_IER_CTSI_BIT          (1 << 7) /* Enable nCTS interrupt */

/* FCR register bits */
#define SC16IS7XX_FCR_FIFO_BIT          (1 << 0) /* Enable FIFO */
#define SC16IS7XX_FCR_RXRESET_BIT       (1 << 1) /* Reset RX FIFO */
#define SC16IS7XX_FCR_TXRESET_BIT       (1 << 2) /* Reset TX FIFO */
#define SC16IS7XX_FCR_RXLVLL_BIT        (1 << 6) /* RX Trigger level LSB */
#define SC16IS7XX_FCR_RXLVLH_BIT        (1 << 7) /* RX Trigger level MSB */

/* FCR register bits - write only if (EFR[4] == 1) */
#define SC16IS7XX_FCR_TXLVLL_BIT        (1 << 4) /* TX Trigger level LSB */
#define SC16IS7XX_FCR_TXLVLH_BIT        (1 << 5) /* TX Trigger level MSB */

/* IIR register bits */
#define SC16IS7XX_IIR_NO_INT_BIT        (1 << 0) /* No interrupts pending */
#define SC16IS7XX_IIR_ID_MASK           0x3e     /* Mask for the interrupt ID */
#define SC16IS7XX_IIR_THRI_SRC          0x02     /* TX holding register empty */
#define SC16IS7XX_IIR_RDI_SRC           0x04     /* RX data interrupt */
#define SC16IS7XX_IIR_RLSE_SRC          0x06     /* RX line status error */
#define SC16IS7XX_IIR_RTOI_SRC          0x0c     /* RX time-out interrupt */
#define SC16IS7XX_IIR_MSI_SRC           0x00     /* Modem status interrupt
                                                  * - only on 75x/76x
                                                  */
#define SC16IS7XX_IIR_INPIN_SRC         0x30     /* Input pin change of state
                                                  * - only on 75x/76x
                                                  */
#define SC16IS7XX_IIR_XOFFI_SRC         0x10     /* Received Xoff */
#define SC16IS7XX_IIR_CTSRTS_SRC        0x20     /* nCTS,nRTS change of state
                                                  * from active (LOW)
                                                  * to inactive (HIGH)
                                                  */
/* LCR register bits */
#define SC16IS7XX_LCR_LENGTH0_BIT       (1 << 0) /* Word length bit 0 */
#define SC16IS7XX_LCR_LENGTH1_BIT       (1 << 1) /* Word length bit 1
                                                  *
                                                  * Word length bits table:
                                                  * 00 -> 5 bit words
                                                  * 01 -> 6 bit words
                                                  * 10 -> 7 bit words
                                                  * 11 -> 8 bit words
                                                  */
#define SC16IS7XX_LCR_STOPLEN_BIT       (1 << 2) /* STOP length bit
                                                  *
                                                  * STOP length bit table:
                                                  * 0 -> 1 stop bit
                                                  * 1 -> 1-1.5 stop bits if
                                                  *      word length is 5,
                                                  *      2 stop bits otherwise
                                                  */
#define SC16IS7XX_LCR_PARITY_BIT        (1 << 3) /* Parity bit enable */
#define SC16IS7XX_LCR_EVENPARITY_BIT    (1 << 4) /* Even parity bit enable */
#define SC16IS7XX_LCR_FORCEPARITY_BIT   (1 << 5) /* 9-bit multidrop parity */
#define SC16IS7XX_LCR_TXBREAK_BIT       (1 << 6) /* TX break enable */
#define SC16IS7XX_LCR_DLAB_BIT          (1 << 7) /* Divisor Latch enable */
#define SC16IS7XX_LCR_WORD_LEN_5        (0x00)
#define SC16IS7XX_LCR_WORD_LEN_6        (0x01)
#define SC16IS7XX_LCR_WORD_LEN_7        (0x02)
#define SC16IS7XX_LCR_WORD_LEN_8        (0x03)
#define SC16IS7XX_LCR_CONF_MODE_A       SC16IS7XX_LCR_DLAB_BIT /* Special
                                                                * reg set */
#define SC16IS7XX_LCR_CONF_MODE_B       0xBF                   /* Enhanced
                                                                * reg set */

/* MCR register bits */
#define SC16IS7XX_MCR_DTR_BIT           (1 << 0) /* DTR complement
                                                  * - only on 75x/76x
                                                  */
#define SC16IS7XX_MCR_RTS_BIT           (1 << 1) /* RTS complement */
#define SC16IS7XX_MCR_TCRTLR_BIT        (1 << 2) /* TCR/TLR register enable */
#define SC16IS7XX_MCR_LOOP_BIT          (1 << 4) /* Enable loopback test mode */
#define SC16IS7XX_MCR_XONANY_BIT        (1 << 5) /* Enable Xon Any
                                                  * - write enabled
                                                  * if (EFR[4] == 1)
                                                  */
#define SC16IS7XX_MCR_IRDA_BIT          (1 << 6) /* Enable IrDA mode
                                                  * - write enabled
                                                  * if (EFR[4] == 1)
                                                  */
#define SC16IS7XX_MCR_CLKSEL_BIT        (1 << 7) /* Divide clock by 4
                                                  * - write enabled
                                                  * if (EFR[4] == 1)
                                                  */

/* LSR register bits */
#define SC16IS7XX_LSR_DR_BIT            (1 << 0) /* Receiver data ready */
#define SC16IS7XX_LSR_OE_BIT            (1 << 1) /* Overrun Error */
#define SC16IS7XX_LSR_PE_BIT            (1 << 2) /* Parity Error */
#define SC16IS7XX_LSR_FE_BIT            (1 << 3) /* Frame Error */
#define SC16IS7XX_LSR_BI_BIT            (1 << 4) /* Break Interrupt */
#define SC16IS7XX_LSR_BRK_ERROR_MASK    0x1E     /* BI, FE, PE, OE bits */
#define SC16IS7XX_LSR_THRE_BIT          (1 << 5) /* TX holding register empty */
#define SC16IS7XX_LSR_TEMT_BIT          (1 << 6) /* Transmitter empty */
#define SC16IS7XX_LSR_FIFOE_BIT         (1 << 7) /* Fifo Error */

/* MSR register bits */
#define SC16IS7XX_MSR_DCTS_BIT          (1 << 0) /* Delta CTS Clear To Send */
#define SC16IS7XX_MSR_DDSR_BIT          (1 << 1) /* Delta DSR Data Set Ready
                                                  * or (IO4)
                                                  * - only on 75x/76x
                                                  */
#define SC16IS7XX_MSR_DRI_BIT           (1 << 2) /* Delta RI Ring Indicator
                                                  * or (IO7)
                                                  * - only on 75x/76x
                                                  */
#define SC16IS7XX_MSR_DCD_BIT           (1 << 3) /* Delta CD Carrier Detect
                                                  * or (IO6)
                                                  * - only on 75x/76x
                                                  */
#define SC16IS7XX_MSR_CTS_BIT           (1 << 4) /* CTS */
#define SC16IS7XX_MSR_DSR_BIT           (1 << 5) /* DSR (IO4)
                                                  * - only on 75x/76x
                                                  */
#define SC16IS7XX_MSR_RI_BIT            (1 << 6) /* RI (IO7)
                                                  * - only on 75x/76x
                                                  */
#define SC16IS7XX_MSR_CD_BIT            (1 << 7) /* CD (IO6)
                                                  * - only on 75x/76x
                                                  */
#define SC16IS7XX_MSR_DELTA_MASK        0x0F     /* Any of the delta bits! */

/*
 * TCR register bits
 * TCR trigger levels are available from 0 to 60 characters with a granularity
 * of four.
 * The programmer must program the TCR such that TCR[3:0] > TCR[7:4]. There is
 * no built-in hardware check to make sure this condition is met. Also, the TCR
 * must be programmed with this condition before auto RTS or software flow
 * control is enabled to avoid spurious operation of the device.
 */
#define SC16IS7XX_TCR_RX_HALT(words)    ((((words) / 4) & 0x0f) << 0)
#define SC16IS7XX_TCR_RX_RESUME(words)  ((((words) / 4) & 0x0f) << 4)

/*
 * TLR register bits
 * If TLR[3:0] or TLR[7:4] are logical 0, the selectable trigger levels via the
 * FIFO Control Register (FCR) are used for the transmit and receive FIFO
 * trigger levels. Trigger levels from 4 characters to 60 characters are
 * available with a granularity of four.
 *
 * When the trigger level setting in TLR is zero, the SC16IS740/750/760 uses the
 * trigger level setting defined in FCR. If TLR has non-zero trigger level value
 * the trigger level defined in FCR is discarded. This applies to both transmit
 * FIFO and receive FIFO trigger level setting.
 *
 * When TLR is used for RX trigger level control, FCR[7:6] should be left at the
 * default state, that is, '00'.
 */
#define SC16IS7XX_TLR_TX_TRIGGER(words) ((((words) / 4) & 0x0f) << 0)
#define SC16IS7XX_TLR_RX_TRIGGER(words) ((((words) / 4) & 0x0f) << 4)

/* IOControl register bits (Only 750/760) */
#define SC16IS7XX_IOCONTROL_LATCH_BIT   (1 << 0) /* Enable input latching */
#define SC16IS7XX_IOCONTROL_MODEM_BIT   (1 << 1) /* Enable GPIO[7:4] as modem pins */
#define SC16IS7XX_IOCONTROL_SRESET_BIT  (1 << 3) /* Software Reset */

/* EFCR register bits */
#define SC16IS7XX_EFCR_9BIT_MODE_BIT    (1 << 0) /* Enable 9-bit or Multidrop
                                                  * mode (RS485) */
#define SC16IS7XX_EFCR_RXDISABLE_BIT    (1 << 1) /* Disable receiver */
#define SC16IS7XX_EFCR_TXDISABLE_BIT    (1 << 2) /* Disable transmitter */
#define SC16IS7XX_EFCR_AUTO_RS485_BIT   (1 << 4) /* Auto RS485 RTS direction */
#define SC16IS7XX_EFCR_RTS_INVERT_BIT   (1 << 5) /* RTS output inversion */
#define SC16IS7XX_EFCR_IRDA_MODE_BIT    (1 << 7) /* IrDA mode
                                                  * 0 = rate upto 115.2 kbit/s
                                                  *   - Only 750/760
                                                  * 1 = rate upto 1.152 Mbit/s
                                                  *   - Only 760
                                                  */

/* EFR register bits */
#define SC16IS7XX_EFR_AUTORTS_BIT       (1 << 6) /* Auto RTS flow ctrl enable */
#define SC16IS7XX_EFR_AUTOCTS_BIT       (1 << 7) /* Auto CTS flow ctrl enable */
#define SC16IS7XX_EFR_XOFF2_DETECT_BIT  (1 << 5) /* Enable Xoff2 detection */
#define SC16IS7XX_EFR_ENABLE_BIT        (1 << 4) /* Enable enhanced functions
                                                  * and writing to IER[7:4],
                                                  * FCR[5:4], MCR[7:5]
                                                  */
#define SC16IS7XX_EFR_SWFLOW3_BIT       (1 << 3) /* SWFLOW bit 3 */
#define SC16IS7XX_EFR_SWFLOW2_BIT       (1 << 2) /* SWFLOW bit 2
                                                  *
                                                  * SWFLOW bits 3 & 2 table:
                                                  * 00 -> no transmitter flow
                                                  *       control
                                                  * 01 -> transmitter generates
                                                  *       XON2 and XOFF2
                                                  * 10 -> transmitter generates
                                                  *       XON1 and XOFF1
                                                  * 11 -> transmitter generates
                                                  *       XON1, XON2, XOFF1 and
                                                  *       XOFF2
                                                  */
#define SC16IS7XX_EFR_SWFLOW1_BIT       (1 << 1) /* SWFLOW bit 2 */
#define SC16IS7XX_EFR_SWFLOW0_BIT       (1 << 0) /* SWFLOW bit 3
                                                  *
                                                  * SWFLOW bits 3 & 2 table:
                                                  * 00 -> no received flow
                                                  *       control
                                                  * 01 -> receiver compares
                                                  *       XON2 and XOFF2
                                                  * 10 -> receiver compares
                                                  *       XON1 and XOFF1
                                                  * 11 -> receiver compares
                                                  *       XON1, XON2, XOFF1 and
                                                  *       XOFF2
                                                  */

/* Misc definitions */
#define SC16IS7XX_FIFO_SIZE             (64)
#define SC16IS7XX_REG_SHIFT             2

struct sc16is7xx_devtype {
        char    name[10];
        int     nr_gpio;
        int     nr_uart;
};

#define SC16IS7XX_RECONF_MD             (1 << 0)
#define SC16IS7XX_RECONF_IER            (1 << 1)
#define SC16IS7XX_RECONF_RS485          (1 << 2)

struct sc16is7xx_one_config {
        unsigned int                    flags;
        u8                              ier_clear;
};

struct sc16is7xx_one {
        struct uart_port                port;
        u8                              line;
        struct kthread_work             tx_work;
        struct kthread_work             reg_work;
        struct sc16is7xx_one_config     config;
};

struct sc16is7xx_port {
        const struct sc16is7xx_devtype  *devtype;
        struct regmap                   *regmap;
        struct clk                      *clk;
#ifdef CONFIG_GPIOLIB
        struct gpio_chip                gpio;
#endif
        unsigned char                   buf[SC16IS7XX_FIFO_SIZE];
        struct kthread_worker           kworker;
        struct task_struct              *kworker_task;
        struct kthread_work             irq_work;
        struct sc16is7xx_one            p[0];
};

static unsigned long sc16is7xx_lines;

static struct uart_driver sc16is7xx_uart = {
        .owner          = THIS_MODULE,
        .dev_name       = "ttySC",
        .nr             = SC16IS7XX_MAX_DEVS,
};

#define to_sc16is7xx_port(p,e)  ((container_of((p), struct sc16is7xx_port, e)))
#define to_sc16is7xx_one(p,e)   ((container_of((p), struct sc16is7xx_one, e)))

static int sc16is7xx_line(struct uart_port *port)
{
        struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);

        return one->line;
}

static u8 sc16is7xx_port_read(struct uart_port *port, u8 reg)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        unsigned int val = 0;
        const u8 line = sc16is7xx_line(port);

        regmap_read(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, &val);

        return val;
}

static void sc16is7xx_port_write(struct uart_port *port, u8 reg, u8 val)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        const u8 line = sc16is7xx_line(port);

        regmap_write(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line, val);
}

static void sc16is7xx_fifo_read(struct uart_port *port, unsigned int rxlen)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        const u8 line = sc16is7xx_line(port);
        u8 addr = (SC16IS7XX_RHR_REG << SC16IS7XX_REG_SHIFT) | line;

        regcache_cache_bypass(s->regmap, true);
        regmap_raw_read(s->regmap, addr, s->buf, rxlen);
        regcache_cache_bypass(s->regmap, false);
}

static void sc16is7xx_fifo_write(struct uart_port *port, u8 to_send)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        const u8 line = sc16is7xx_line(port);
        u8 addr = (SC16IS7XX_THR_REG << SC16IS7XX_REG_SHIFT) | line;

        /*
         * Don't send zero-length data, at least on SPI it confuses the chip
         * delivering wrong TXLVL data.
         */
        if (unlikely(!to_send))
                return;

        regcache_cache_bypass(s->regmap, true);
        regmap_raw_write(s->regmap, addr, s->buf, to_send);
        regcache_cache_bypass(s->regmap, false);
}

static void sc16is7xx_port_update(struct uart_port *port, u8 reg,
                                  u8 mask, u8 val)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        const u8 line = sc16is7xx_line(port);

        regmap_update_bits(s->regmap, (reg << SC16IS7XX_REG_SHIFT) | line,
                           mask, val);
}

static int sc16is7xx_alloc_line(void)
{
        int i;

        BUILD_BUG_ON(SC16IS7XX_MAX_DEVS > BITS_PER_LONG);

        for (i = 0; i < SC16IS7XX_MAX_DEVS; i++)
                if (!test_and_set_bit(i, &sc16is7xx_lines))
                        break;

        return i;
}

static void sc16is7xx_power(struct uart_port *port, int on)
{
        sc16is7xx_port_update(port, SC16IS7XX_IER_REG,
                              SC16IS7XX_IER_SLEEP_BIT,
                              on ? 0 : SC16IS7XX_IER_SLEEP_BIT);
}

static const struct sc16is7xx_devtype sc16is74x_devtype = {
        .name           = "SC16IS74X",
        .nr_gpio        = 0,
        .nr_uart        = 1,
};

static const struct sc16is7xx_devtype sc16is750_devtype = {
        .name           = "SC16IS750",
        .nr_gpio        = 8,
        .nr_uart        = 1,
};

static const struct sc16is7xx_devtype sc16is752_devtype = {
        .name           = "SC16IS752",
        .nr_gpio        = 8,
        .nr_uart        = 2,
};

static const struct sc16is7xx_devtype sc16is760_devtype = {
        .name           = "SC16IS760",
        .nr_gpio        = 8,
        .nr_uart        = 1,
};

static const struct sc16is7xx_devtype sc16is762_devtype = {
        .name           = "SC16IS762",
        .nr_gpio        = 8,
        .nr_uart        = 2,
};

static bool sc16is7xx_regmap_volatile(struct device *dev, unsigned int reg)
{
        switch (reg >> SC16IS7XX_REG_SHIFT) {
        case SC16IS7XX_RHR_REG:
        case SC16IS7XX_IIR_REG:
        case SC16IS7XX_LSR_REG:
        case SC16IS7XX_MSR_REG:
        case SC16IS7XX_TXLVL_REG:
        case SC16IS7XX_RXLVL_REG:
        case SC16IS7XX_IOSTATE_REG:
                return true;
        default:
                break;
        }

        return false;
}

static bool sc16is7xx_regmap_precious(struct device *dev, unsigned int reg)
{
        switch (reg >> SC16IS7XX_REG_SHIFT) {
        case SC16IS7XX_RHR_REG:
                return true;
        default:
                break;
        }

        return false;
}

static int sc16is7xx_set_baud(struct uart_port *port, int baud)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        u8 lcr;
        u8 prescaler = 0;
        unsigned long clk = port->uartclk, div = clk / 16 / baud;

        if (div > 0xffff) {
                prescaler = SC16IS7XX_MCR_CLKSEL_BIT;
                div /= 4;
        }

        lcr = sc16is7xx_port_read(port, SC16IS7XX_LCR_REG);

        /* Open the LCR divisors for configuration */
        sc16is7xx_port_write(port, SC16IS7XX_LCR_REG,
                             SC16IS7XX_LCR_CONF_MODE_B);

        /* Enable enhanced features */
        regcache_cache_bypass(s->regmap, true);
        sc16is7xx_port_write(port, SC16IS7XX_EFR_REG,
                             SC16IS7XX_EFR_ENABLE_BIT);
        regcache_cache_bypass(s->regmap, false);

        /* Put LCR back to the normal mode */
        sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr);

        sc16is7xx_port_update(port, SC16IS7XX_MCR_REG,
                              SC16IS7XX_MCR_CLKSEL_BIT,
                              prescaler);

        /* Open the LCR divisors for configuration */
        sc16is7xx_port_write(port, SC16IS7XX_LCR_REG,
                             SC16IS7XX_LCR_CONF_MODE_A);

        /* Write the new divisor */
        regcache_cache_bypass(s->regmap, true);
        sc16is7xx_port_write(port, SC16IS7XX_DLH_REG, div / 256);
        sc16is7xx_port_write(port, SC16IS7XX_DLL_REG, div % 256);
        regcache_cache_bypass(s->regmap, false);

        /* Put LCR back to the normal mode */
        sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr);

        return DIV_ROUND_CLOSEST(clk / 16, div);
}

static void sc16is7xx_handle_rx(struct uart_port *port, unsigned int rxlen,
                                unsigned int iir)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        unsigned int lsr = 0, ch, flag, bytes_read, i;
        bool read_lsr = (iir == SC16IS7XX_IIR_RLSE_SRC) ? true : false;

        if (unlikely(rxlen >= sizeof(s->buf))) {
                dev_warn_ratelimited(port->dev,
                                     "ttySC%i: Possible RX FIFO overrun: %d\n",
                                     port->line, rxlen);
                port->icount.buf_overrun++;
                /* Ensure sanity of RX level */
                rxlen = sizeof(s->buf);
        }

        while (rxlen) {
                /* Only read lsr if there are possible errors in FIFO */
                if (read_lsr) {
                        lsr = sc16is7xx_port_read(port, SC16IS7XX_LSR_REG);
                        if (!(lsr & SC16IS7XX_LSR_FIFOE_BIT))
                                read_lsr = false; /* No errors left in FIFO */
                } else
                        lsr = 0;

                if (read_lsr) {
                        s->buf[0] = sc16is7xx_port_read(port, SC16IS7XX_RHR_REG);
                        bytes_read = 1;
                } else {
                        sc16is7xx_fifo_read(port, rxlen);
                        bytes_read = rxlen;
                }

                lsr &= SC16IS7XX_LSR_BRK_ERROR_MASK;

                port->icount.rx++;
                flag = TTY_NORMAL;

                if (unlikely(lsr)) {
                        if (lsr & SC16IS7XX_LSR_BI_BIT) {
                                port->icount.brk++;
                                if (uart_handle_break(port))
                                        continue;
                        } else if (lsr & SC16IS7XX_LSR_PE_BIT)
                                port->icount.parity++;
                        else if (lsr & SC16IS7XX_LSR_FE_BIT)
                                port->icount.frame++;
                        else if (lsr & SC16IS7XX_LSR_OE_BIT)
                                port->icount.overrun++;

                        lsr &= port->read_status_mask;
                        if (lsr & SC16IS7XX_LSR_BI_BIT)
                                flag = TTY_BREAK;
                        else if (lsr & SC16IS7XX_LSR_PE_BIT)
                                flag = TTY_PARITY;
                        else if (lsr & SC16IS7XX_LSR_FE_BIT)
                                flag = TTY_FRAME;
                        else if (lsr & SC16IS7XX_LSR_OE_BIT)
                                flag = TTY_OVERRUN;
                }

                for (i = 0; i < bytes_read; ++i) {
                        ch = s->buf[i];
                        if (uart_handle_sysrq_char(port, ch))
                                continue;

                        if (lsr & port->ignore_status_mask)
                                continue;

                        uart_insert_char(port, lsr, SC16IS7XX_LSR_OE_BIT, ch,
                                         flag);
                }
                rxlen -= bytes_read;
        }

        tty_flip_buffer_push(&port->state->port);
}

static void sc16is7xx_handle_tx(struct uart_port *port)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        struct circ_buf *xmit = &port->state->xmit;
        unsigned int txlen, to_send, i;

        if (unlikely(port->x_char)) {
                sc16is7xx_port_write(port, SC16IS7XX_THR_REG, port->x_char);
                port->icount.tx++;
                port->x_char = 0;
                return;
        }

        if (uart_circ_empty(xmit) || uart_tx_stopped(port))
                return;

        /* Get length of data pending in circular buffer */
        to_send = uart_circ_chars_pending(xmit);
        if (likely(to_send)) {
                /* Limit to size of TX FIFO */
                txlen = sc16is7xx_port_read(port, SC16IS7XX_TXLVL_REG);
                if (txlen > SC16IS7XX_FIFO_SIZE) {
                        dev_err_ratelimited(port->dev,
                                "chip reports %d free bytes in TX fifo, but it only has %d",
                                txlen, SC16IS7XX_FIFO_SIZE);
                        txlen = 0;
                }
                to_send = (to_send > txlen) ? txlen : to_send;

                /* Add data to send */
                port->icount.tx += to_send;

                /* Convert to linear buffer */
                for (i = 0; i < to_send; ++i) {
                        s->buf[i] = xmit->buf[xmit->tail];
                        xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
                }

                sc16is7xx_fifo_write(port, to_send);
        }

        if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
                uart_write_wakeup(port);
}

static void sc16is7xx_port_irq(struct sc16is7xx_port *s, int portno)
{
        struct uart_port *port = &s->p[portno].port;

        do {
                unsigned int iir, msr, rxlen;

                iir = sc16is7xx_port_read(port, SC16IS7XX_IIR_REG);
                if (iir & SC16IS7XX_IIR_NO_INT_BIT)
                        break;

                iir &= SC16IS7XX_IIR_ID_MASK;

                switch (iir) {
                case SC16IS7XX_IIR_RDI_SRC:
                case SC16IS7XX_IIR_RLSE_SRC:
                case SC16IS7XX_IIR_RTOI_SRC:
                case SC16IS7XX_IIR_XOFFI_SRC:
                        rxlen = sc16is7xx_port_read(port, SC16IS7XX_RXLVL_REG);
                        if (rxlen)
                                sc16is7xx_handle_rx(port, rxlen, iir);
                        break;

                case SC16IS7XX_IIR_CTSRTS_SRC:
                        msr = sc16is7xx_port_read(port, SC16IS7XX_MSR_REG);
                        uart_handle_cts_change(port,
                                               !!(msr & SC16IS7XX_MSR_DCTS_BIT));
                        break;
                case SC16IS7XX_IIR_THRI_SRC:
                        sc16is7xx_handle_tx(port);
                        break;
                default:
                        dev_err_ratelimited(port->dev,
                                            "ttySC%i: Unexpected interrupt: %x",
                                            port->line, iir);
                        break;
                }
        } while (1);
}

static void sc16is7xx_ist(struct kthread_work *ws)
{
        struct sc16is7xx_port *s = to_sc16is7xx_port(ws, irq_work);
        int i;

        for (i = 0; i < s->devtype->nr_uart; ++i)
                sc16is7xx_port_irq(s, i);
}

static irqreturn_t sc16is7xx_irq(int irq, void *dev_id)
{
        struct sc16is7xx_port *s = (struct sc16is7xx_port *)dev_id;

        queue_kthread_work(&s->kworker, &s->irq_work);

        return IRQ_HANDLED;
}

static void sc16is7xx_tx_proc(struct kthread_work *ws)
{
        struct uart_port *port = &(to_sc16is7xx_one(ws, tx_work)->port);

        if ((port->rs485.flags & SER_RS485_ENABLED) &&
            (port->rs485.delay_rts_before_send > 0))
                msleep(port->rs485.delay_rts_before_send);

        sc16is7xx_handle_tx(port);
}

static void sc16is7xx_reconf_rs485(struct uart_port *port)
{
        const u32 mask = SC16IS7XX_EFCR_AUTO_RS485_BIT |
                         SC16IS7XX_EFCR_RTS_INVERT_BIT;
        u32 efcr = 0;
        struct serial_rs485 *rs485 = &port->rs485;
        unsigned long irqflags;

        spin_lock_irqsave(&port->lock, irqflags);
        if (rs485->flags & SER_RS485_ENABLED) {
                efcr |= SC16IS7XX_EFCR_AUTO_RS485_BIT;

                if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
                        efcr |= SC16IS7XX_EFCR_RTS_INVERT_BIT;
        }
        spin_unlock_irqrestore(&port->lock, irqflags);

        sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG, mask, efcr);
}

static void sc16is7xx_reg_proc(struct kthread_work *ws)
{
        struct sc16is7xx_one *one = to_sc16is7xx_one(ws, reg_work);
        struct sc16is7xx_one_config config;
        unsigned long irqflags;

        spin_lock_irqsave(&one->port.lock, irqflags);
        config = one->config;
        memset(&one->config, 0, sizeof(one->config));
        spin_unlock_irqrestore(&one->port.lock, irqflags);

        if (config.flags & SC16IS7XX_RECONF_MD) {
                sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG,
                                      SC16IS7XX_MCR_LOOP_BIT,
                                      (one->port.mctrl & TIOCM_LOOP) ?
                                      SC16IS7XX_MCR_LOOP_BIT : 0);
                sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG,
                                      SC16IS7XX_MCR_RTS_BIT,
                                      (one->port.mctrl & TIOCM_RTS) ?
                                      SC16IS7XX_MCR_RTS_BIT : 0);
                sc16is7xx_port_update(&one->port, SC16IS7XX_MCR_REG,
                                      SC16IS7XX_MCR_DTR_BIT,
                                      (one->port.mctrl & TIOCM_DTR) ?
                                      SC16IS7XX_MCR_DTR_BIT : 0);
        }
        if (config.flags & SC16IS7XX_RECONF_IER)
                sc16is7xx_port_update(&one->port, SC16IS7XX_IER_REG,
                                      config.ier_clear, 0);

        if (config.flags & SC16IS7XX_RECONF_RS485)
                sc16is7xx_reconf_rs485(&one->port);
}

static void sc16is7xx_ier_clear(struct uart_port *port, u8 bit)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);

        one->config.flags |= SC16IS7XX_RECONF_IER;
        one->config.ier_clear |= bit;
        queue_kthread_work(&s->kworker, &one->reg_work);
}

static void sc16is7xx_stop_tx(struct uart_port *port)
{
        sc16is7xx_ier_clear(port, SC16IS7XX_IER_THRI_BIT);
}

static void sc16is7xx_stop_rx(struct uart_port *port)
{
        sc16is7xx_ier_clear(port, SC16IS7XX_IER_RDI_BIT);
}

static void sc16is7xx_start_tx(struct uart_port *port)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);

        queue_kthread_work(&s->kworker, &one->tx_work);
}

static unsigned int sc16is7xx_tx_empty(struct uart_port *port)
{
        unsigned int lsr;

        lsr = sc16is7xx_port_read(port, SC16IS7XX_LSR_REG);

        return (lsr & SC16IS7XX_LSR_TEMT_BIT) ? TIOCSER_TEMT : 0;
}

static unsigned int sc16is7xx_get_mctrl(struct uart_port *port)
{
        /* DCD and DSR are not wired and CTS/RTS is handled automatically
         * so just indicate DSR and CAR asserted
         */
        return TIOCM_DSR | TIOCM_CAR;
}

static void sc16is7xx_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);

        one->config.flags |= SC16IS7XX_RECONF_MD;
        queue_kthread_work(&s->kworker, &one->reg_work);
}

static void sc16is7xx_break_ctl(struct uart_port *port, int break_state)
{
        sc16is7xx_port_update(port, SC16IS7XX_LCR_REG,
                              SC16IS7XX_LCR_TXBREAK_BIT,
                              break_state ? SC16IS7XX_LCR_TXBREAK_BIT : 0);
}

static void sc16is7xx_set_termios(struct uart_port *port,
                                  struct ktermios *termios,
                                  struct ktermios *old)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        unsigned int lcr, flow = 0;
        int baud;

        /* Mask termios capabilities we don't support */
        termios->c_cflag &= ~CMSPAR;

        /* Word size */
        switch (termios->c_cflag & CSIZE) {
        case CS5:
                lcr = SC16IS7XX_LCR_WORD_LEN_5;
                break;
        case CS6:
                lcr = SC16IS7XX_LCR_WORD_LEN_6;
                break;
        case CS7:
                lcr = SC16IS7XX_LCR_WORD_LEN_7;
                break;
        case CS8:
                lcr = SC16IS7XX_LCR_WORD_LEN_8;
                break;
        default:
                lcr = SC16IS7XX_LCR_WORD_LEN_8;
                termios->c_cflag &= ~CSIZE;
                termios->c_cflag |= CS8;
                break;
        }

        /* Parity */
        if (termios->c_cflag & PARENB) {
                lcr |= SC16IS7XX_LCR_PARITY_BIT;
                if (!(termios->c_cflag & PARODD))
                        lcr |= SC16IS7XX_LCR_EVENPARITY_BIT;
        }

        /* Stop bits */
        if (termios->c_cflag & CSTOPB)
                lcr |= SC16IS7XX_LCR_STOPLEN_BIT; /* 2 stops */

        /* Set read status mask */
        port->read_status_mask = SC16IS7XX_LSR_OE_BIT;
        if (termios->c_iflag & INPCK)
                port->read_status_mask |= SC16IS7XX_LSR_PE_BIT |
                                          SC16IS7XX_LSR_FE_BIT;
        if (termios->c_iflag & (BRKINT | PARMRK))
                port->read_status_mask |= SC16IS7XX_LSR_BI_BIT;

        /* Set status ignore mask */
        port->ignore_status_mask = 0;
        if (termios->c_iflag & IGNBRK)
                port->ignore_status_mask |= SC16IS7XX_LSR_BI_BIT;
        if (!(termios->c_cflag & CREAD))
                port->ignore_status_mask |= SC16IS7XX_LSR_BRK_ERROR_MASK;

        sc16is7xx_port_write(port, SC16IS7XX_LCR_REG,
                             SC16IS7XX_LCR_CONF_MODE_B);

        /* Configure flow control */
        regcache_cache_bypass(s->regmap, true);
        sc16is7xx_port_write(port, SC16IS7XX_XON1_REG, termios->c_cc[VSTART]);
        sc16is7xx_port_write(port, SC16IS7XX_XOFF1_REG, termios->c_cc[VSTOP]);
        if (termios->c_cflag & CRTSCTS)
                flow |= SC16IS7XX_EFR_AUTOCTS_BIT |
                        SC16IS7XX_EFR_AUTORTS_BIT;
        if (termios->c_iflag & IXON)
                flow |= SC16IS7XX_EFR_SWFLOW3_BIT;
        if (termios->c_iflag & IXOFF)
                flow |= SC16IS7XX_EFR_SWFLOW1_BIT;

        sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, flow);
        regcache_cache_bypass(s->regmap, false);

        /* Update LCR register */
        sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr);

        /* Get baud rate generator configuration */
        baud = uart_get_baud_rate(port, termios, old,
                                  port->uartclk / 16 / 4 / 0xffff,
                                  port->uartclk / 16);

        /* Setup baudrate generator */
        baud = sc16is7xx_set_baud(port, baud);

        /* Update timeout according to new baud rate */
        uart_update_timeout(port, termios->c_cflag, baud);
}

static int sc16is7xx_config_rs485(struct uart_port *port,
                                  struct serial_rs485 *rs485)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);

        if (rs485->flags & SER_RS485_ENABLED) {
                bool rts_during_rx, rts_during_tx;

                rts_during_rx = rs485->flags & SER_RS485_RTS_AFTER_SEND;
                rts_during_tx = rs485->flags & SER_RS485_RTS_ON_SEND;

                if (rts_during_rx == rts_during_tx)
                        dev_err(port->dev,
                                "unsupported RTS signalling on_send:%d after_send:%d - exactly one of RS485 RTS flags should be set\n",
                                rts_during_tx, rts_during_rx);

                /*
                 * RTS signal is handled by HW, it's timing can't be influenced.
                 * However, it's sometimes useful to delay TX even without RTS
                 * control therefore we try to handle .delay_rts_before_send.
                 */
                if (rs485->delay_rts_after_send)
                        return -EINVAL;
        }

        port->rs485 = *rs485;
        one->config.flags |= SC16IS7XX_RECONF_RS485;
        queue_kthread_work(&s->kworker, &one->reg_work);

        return 0;
}

static int sc16is7xx_startup(struct uart_port *port)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);
        unsigned int val;

        sc16is7xx_power(port, 1);

        /* Reset FIFOs*/
        val = SC16IS7XX_FCR_RXRESET_BIT | SC16IS7XX_FCR_TXRESET_BIT;
        sc16is7xx_port_write(port, SC16IS7XX_FCR_REG, val);
        udelay(5);
        sc16is7xx_port_write(port, SC16IS7XX_FCR_REG,
                             SC16IS7XX_FCR_FIFO_BIT);

        /* Enable EFR */
        sc16is7xx_port_write(port, SC16IS7XX_LCR_REG,
                             SC16IS7XX_LCR_CONF_MODE_B);

        regcache_cache_bypass(s->regmap, true);

        /* Enable write access to enhanced features and internal clock div */
        sc16is7xx_port_write(port, SC16IS7XX_EFR_REG,
                             SC16IS7XX_EFR_ENABLE_BIT);

        /* Enable TCR/TLR */
        sc16is7xx_port_update(port, SC16IS7XX_MCR_REG,
                              SC16IS7XX_MCR_TCRTLR_BIT,
                              SC16IS7XX_MCR_TCRTLR_BIT);

        /* Configure flow control levels */

        /* Flow control halt level 48, resume level 24 */
        sc16is7xx_port_write(port, SC16IS7XX_TCR_REG,
                             SC16IS7XX_TCR_RX_RESUME(24) |
                             SC16IS7XX_TCR_RX_HALT(48));

        regcache_cache_bypass(s->regmap, false);

        /* Now, initialize the UART */
        sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, SC16IS7XX_LCR_WORD_LEN_8);

        /* Enable the Rx and Tx FIFO */
        sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG,
                              SC16IS7XX_EFCR_RXDISABLE_BIT |
                              SC16IS7XX_EFCR_TXDISABLE_BIT,
                              0);

        /* Enable RX, TX, CTS change interrupts */
        val = SC16IS7XX_IER_RDI_BIT | SC16IS7XX_IER_THRI_BIT |
              SC16IS7XX_IER_CTSI_BIT;
        sc16is7xx_port_write(port, SC16IS7XX_IER_REG, val);

        return 0;
}

static void sc16is7xx_shutdown(struct uart_port *port)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);

        /* Disable all interrupts */
        sc16is7xx_port_write(port, SC16IS7XX_IER_REG, 0);
        /* Disable TX/RX */
        sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG,
                              SC16IS7XX_EFCR_RXDISABLE_BIT |
                              SC16IS7XX_EFCR_TXDISABLE_BIT,
                              SC16IS7XX_EFCR_RXDISABLE_BIT |
                              SC16IS7XX_EFCR_TXDISABLE_BIT);

        sc16is7xx_power(port, 0);

        flush_kthread_worker(&s->kworker);
}

static const char *sc16is7xx_type(struct uart_port *port)
{
        struct sc16is7xx_port *s = dev_get_drvdata(port->dev);

        return (port->type == PORT_SC16IS7XX) ? s->devtype->name : NULL;
}

static int sc16is7xx_request_port(struct uart_port *port)
{
        /* Do nothing */
        return 0;
}

static void sc16is7xx_config_port(struct uart_port *port, int flags)
{
        if (flags & UART_CONFIG_TYPE)
                port->type = PORT_SC16IS7XX;
}

static int sc16is7xx_verify_port(struct uart_port *port,
                                 struct serial_struct *s)
{
        if ((s->type != PORT_UNKNOWN) && (s->type != PORT_SC16IS7XX))
                return -EINVAL;
        if (s->irq != port->irq)
                return -EINVAL;

        return 0;
}

static void sc16is7xx_pm(struct uart_port *port, unsigned int state,
                         unsigned int oldstate)
{
        sc16is7xx_power(port, (state == UART_PM_STATE_ON) ? 1 : 0);
}

static void sc16is7xx_null_void(struct uart_port *port)
{
        /* Do nothing */
}

static const struct uart_ops sc16is7xx_ops = {
        .tx_empty       = sc16is7xx_tx_empty,
        .set_mctrl      = sc16is7xx_set_mctrl,
        .get_mctrl      = sc16is7xx_get_mctrl,
        .stop_tx        = sc16is7xx_stop_tx,
        .start_tx       = sc16is7xx_start_tx,
        .stop_rx        = sc16is7xx_stop_rx,
        .break_ctl      = sc16is7xx_break_ctl,
        .startup        = sc16is7xx_startup,
        .shutdown       = sc16is7xx_shutdown,
        .set_termios    = sc16is7xx_set_termios,
        .type           = sc16is7xx_type,
        .request_port   = sc16is7xx_request_port,
        .release_port   = sc16is7xx_null_void,
        .config_port    = sc16is7xx_config_port,
        .verify_port    = sc16is7xx_verify_port,
        .pm             = sc16is7xx_pm,
};

#ifdef CONFIG_GPIOLIB
static int sc16is7xx_gpio_get(struct gpio_chip *chip, unsigned offset)
{
        unsigned int val;
        struct sc16is7xx_port *s = container_of(chip, struct sc16is7xx_port,
                                                gpio);
        struct uart_port *port = &s->p[0].port;

        val = sc16is7xx_port_read(port, SC16IS7XX_IOSTATE_REG);

        return !!(val & BIT(offset));
}

static void sc16is7xx_gpio_set(struct gpio_chip *chip, unsigned offset, int val)
{
        struct sc16is7xx_port *s = container_of(chip, struct sc16is7xx_port,
                                                gpio);
        struct uart_port *port = &s->p[0].port;

        sc16is7xx_port_update(port, SC16IS7XX_IOSTATE_REG, BIT(offset),
                              val ? BIT(offset) : 0);
}

static int sc16is7xx_gpio_direction_input(struct gpio_chip *chip,
                                          unsigned offset)
{
        struct sc16is7xx_port *s = container_of(chip, struct sc16is7xx_port,
                                                gpio);
        struct uart_port *port = &s->p[0].port;

        sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset), 0);

        return 0;
}

static int sc16is7xx_gpio_direction_output(struct gpio_chip *chip,
                                           unsigned offset, int val)
{
        struct sc16is7xx_port *s = container_of(chip, struct sc16is7xx_port,
                                                gpio);
        struct uart_port *port = &s->p[0].port;

        sc16is7xx_port_update(port, SC16IS7XX_IOSTATE_REG, BIT(offset),
                              val ? BIT(offset) : 0);
        sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset),
                              BIT(offset));

        return 0;
}
#endif

static int sc16is7xx_probe(struct device *dev,
                           const struct sc16is7xx_devtype *devtype,
                           struct regmap *regmap, int irq, unsigned long flags)
{
        struct sched_param sched_param = { .sched_priority = MAX_RT_PRIO / 2 };
        unsigned long freq, *pfreq = dev_get_platdata(dev);
        int i, ret;
        struct sc16is7xx_port *s;

        if (IS_ERR(regmap))
                return PTR_ERR(regmap);

        /* Alloc port structure */
        s = devm_kzalloc(dev, sizeof(*s) +
                         sizeof(struct sc16is7xx_one) * devtype->nr_uart,
                         GFP_KERNEL);
        if (!s) {
                dev_err(dev, "Error allocating port structure\n");
                return -ENOMEM;
        }

        s->clk = devm_clk_get(dev, NULL);
        if (IS_ERR(s->clk)) {
                if (pfreq)
                        freq = *pfreq;
                else
                        return PTR_ERR(s->clk);
        } else {
                clk_prepare_enable(s->clk);
                freq = clk_get_rate(s->clk);
        }

        s->regmap = regmap;
        s->devtype = devtype;
        dev_set_drvdata(dev, s);

        init_kthread_worker(&s->kworker);
        init_kthread_work(&s->irq_work, sc16is7xx_ist);
        s->kworker_task = kthread_run(kthread_worker_fn, &s->kworker,
                                      "sc16is7xx");
        if (IS_ERR(s->kworker_task)) {
                ret = PTR_ERR(s->kworker_task);
                goto out_clk;
        }
        sched_setscheduler(s->kworker_task, SCHED_FIFO, &sched_param);

#ifdef CONFIG_GPIOLIB
        if (devtype->nr_gpio) {
                /* Setup GPIO cotroller */
                s->gpio.owner            = THIS_MODULE;
                s->gpio.parent           = dev;
                s->gpio.label            = dev_name(dev);
                s->gpio.direction_input  = sc16is7xx_gpio_direction_input;
                s->gpio.get              = sc16is7xx_gpio_get;
                s->gpio.direction_output = sc16is7xx_gpio_direction_output;
                s->gpio.set              = sc16is7xx_gpio_set;
                s->gpio.base             = -1;
                s->gpio.ngpio            = devtype->nr_gpio;
                s->gpio.can_sleep        = 1;
                ret = gpiochip_add(&s->gpio);
                if (ret)
                        goto out_thread;
        }
#endif

        for (i = 0; i < devtype->nr_uart; ++i) {
                s->p[i].line            = i;
                /* Initialize port data */
                s->p[i].port.dev        = dev;
                s->p[i].port.irq        = irq;
                s->p[i].port.type       = PORT_SC16IS7XX;
                s->p[i].port.fifosize   = SC16IS7XX_FIFO_SIZE;
                s->p[i].port.flags      = UPF_FIXED_TYPE | UPF_LOW_LATENCY;
                s->p[i].port.iotype     = UPIO_PORT;
                s->p[i].port.uartclk    = freq;
                s->p[i].port.rs485_config = sc16is7xx_config_rs485;
                s->p[i].port.ops        = &sc16is7xx_ops;
                s->p[i].port.line       = sc16is7xx_alloc_line();
                if (s->p[i].port.line >= SC16IS7XX_MAX_DEVS) {
                        ret = -ENOMEM;
                        goto out_ports;
                }

                /* Disable all interrupts */
                sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_IER_REG, 0);
                /* Disable TX/RX */
                sc16is7xx_port_write(&s->p[i].port, SC16IS7XX_EFCR_REG,
                                     SC16IS7XX_EFCR_RXDISABLE_BIT |
                                     SC16IS7XX_EFCR_TXDISABLE_BIT);
                /* Initialize kthread work structs */
                init_kthread_work(&s->p[i].tx_work, sc16is7xx_tx_proc);
                init_kthread_work(&s->p[i].reg_work, sc16is7xx_reg_proc);
                /* Register port */
                uart_add_one_port(&sc16is7xx_uart, &s->p[i].port);
                /* Go to suspend mode */
                sc16is7xx_power(&s->p[i].port, 0);
        }

        /* Setup interrupt */
        ret = devm_request_irq(dev, irq, sc16is7xx_irq,
                               IRQF_ONESHOT | flags, dev_name(dev), s);
        if (!ret)
                return 0;

out_ports:
        for (i--; i >= 0; i--) {
                uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port);
                clear_bit(s->p[i].port.line, &sc16is7xx_lines);
        }

#ifdef CONFIG_GPIOLIB
        if (devtype->nr_gpio)
                gpiochip_remove(&s->gpio);

out_thread:
#endif
        kthread_stop(s->kworker_task);

out_clk:
        if (!IS_ERR(s->clk))
                clk_disable_unprepare(s->clk);

        return ret;
}

static int sc16is7xx_remove(struct device *dev)
{
        struct sc16is7xx_port *s = dev_get_drvdata(dev);
        int i;

#ifdef CONFIG_GPIOLIB
        if (s->devtype->nr_gpio)
                gpiochip_remove(&s->gpio);
#endif

        for (i = 0; i < s->devtype->nr_uart; i++) {
                uart_remove_one_port(&sc16is7xx_uart, &s->p[i].port);
                clear_bit(s->p[i].port.line, &sc16is7xx_lines);
                sc16is7xx_power(&s->p[i].port, 0);
        }

        flush_kthread_worker(&s->kworker);
        kthread_stop(s->kworker_task);

        if (!IS_ERR(s->clk))
                clk_disable_unprepare(s->clk);

        return 0;
}

static const struct of_device_id __maybe_unused sc16is7xx_dt_ids[] = {
        { .compatible = "nxp,sc16is740",        .data = &sc16is74x_devtype, },
        { .compatible = "nxp,sc16is741",        .data = &sc16is74x_devtype, },
        { .compatible = "nxp,sc16is750",        .data = &sc16is750_devtype, },
        { .compatible = "nxp,sc16is752",        .data = &sc16is752_devtype, },
        { .compatible = "nxp,sc16is760",        .data = &sc16is760_devtype, },
        { .compatible = "nxp,sc16is762",        .data = &sc16is762_devtype, },
        { }
};
MODULE_DEVICE_TABLE(of, sc16is7xx_dt_ids);

static struct regmap_config regcfg = {
        .reg_bits = 7,
        .pad_bits = 1,
        .val_bits = 8,
        .cache_type = REGCACHE_RBTREE,
        .volatile_reg = sc16is7xx_regmap_volatile,
        .precious_reg = sc16is7xx_regmap_precious,
};

#ifdef CONFIG_SERIAL_SC16IS7XX_SPI
static int sc16is7xx_spi_probe(struct spi_device *spi)
{
        const struct sc16is7xx_devtype *devtype;
        unsigned long flags = 0;
        struct regmap *regmap;
        int ret;

        /* Setup SPI bus */
        spi->bits_per_word      = 8;
        /* only supports mode 0 on SC16IS762 */
        spi->mode               = spi->mode ? : SPI_MODE_0;
        spi->max_speed_hz       = spi->max_speed_hz ? : 15000000;
        ret = spi_setup(spi);
        if (ret)
                return ret;

        if (spi->dev.of_node) {
                const struct of_device_id *of_id =
                        of_match_device(sc16is7xx_dt_ids, &spi->dev);

                if (!of_id)
                        return -ENODEV;

                devtype = (struct sc16is7xx_devtype *)of_id->data;
        } else {
                const struct spi_device_id *id_entry = spi_get_device_id(spi);

                devtype = (struct sc16is7xx_devtype *)id_entry->driver_data;
                flags = IRQF_TRIGGER_FALLING;
        }

        regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) |
                              (devtype->nr_uart - 1);
        regmap = devm_regmap_init_spi(spi, &regcfg);

        return sc16is7xx_probe(&spi->dev, devtype, regmap, spi->irq, flags);
}

static int sc16is7xx_spi_remove(struct spi_device *spi)
{
        return sc16is7xx_remove(&spi->dev);
}

static const struct spi_device_id sc16is7xx_spi_id_table[] = {
        { "sc16is74x",  (kernel_ulong_t)&sc16is74x_devtype, },
        { "sc16is740",  (kernel_ulong_t)&sc16is74x_devtype, },
        { "sc16is741",  (kernel_ulong_t)&sc16is74x_devtype, },
        { "sc16is750",  (kernel_ulong_t)&sc16is750_devtype, },
        { "sc16is752",  (kernel_ulong_t)&sc16is752_devtype, },
        { "sc16is760",  (kernel_ulong_t)&sc16is760_devtype, },
        { "sc16is762",  (kernel_ulong_t)&sc16is762_devtype, },
        { }
};

MODULE_DEVICE_TABLE(spi, sc16is7xx_spi_id_table);

static struct spi_driver sc16is7xx_spi_uart_driver = {
        .driver = {
                .name           = SC16IS7XX_NAME,
                .of_match_table = of_match_ptr(sc16is7xx_dt_ids),
        },
        .probe          = sc16is7xx_spi_probe,
        .remove         = sc16is7xx_spi_remove,
        .id_table       = sc16is7xx_spi_id_table,
};

MODULE_ALIAS("spi:sc16is7xx");
#endif

#ifdef CONFIG_SERIAL_SC16IS7XX_I2C
static int sc16is7xx_i2c_probe(struct i2c_client *i2c,
                               const struct i2c_device_id *id)
{
        const struct sc16is7xx_devtype *devtype;
        unsigned long flags = 0;
        struct regmap *regmap;

        if (i2c->dev.of_node) {
                const struct of_device_id *of_id =
                                of_match_device(sc16is7xx_dt_ids, &i2c->dev);

                if (!of_id)
                        return -ENODEV;

                devtype = (struct sc16is7xx_devtype *)of_id->data;
        } else {
                devtype = (struct sc16is7xx_devtype *)id->driver_data;
                flags = IRQF_TRIGGER_FALLING;
        }

        regcfg.max_register = (0xf << SC16IS7XX_REG_SHIFT) |
                              (devtype->nr_uart - 1);
        regmap = devm_regmap_init_i2c(i2c, &regcfg);

        return sc16is7xx_probe(&i2c->dev, devtype, regmap, i2c->irq, flags);
}

static int sc16is7xx_i2c_remove(struct i2c_client *client)
{
        return sc16is7xx_remove(&client->dev);
}

static const struct i2c_device_id sc16is7xx_i2c_id_table[] = {
        { "sc16is74x",  (kernel_ulong_t)&sc16is74x_devtype, },
        { "sc16is740",  (kernel_ulong_t)&sc16is74x_devtype, },
        { "sc16is741",  (kernel_ulong_t)&sc16is74x_devtype, },
        { "sc16is750",  (kernel_ulong_t)&sc16is750_devtype, },
        { "sc16is752",  (kernel_ulong_t)&sc16is752_devtype, },
        { "sc16is760",  (kernel_ulong_t)&sc16is760_devtype, },
        { "sc16is762",  (kernel_ulong_t)&sc16is762_devtype, },
        { }
};
MODULE_DEVICE_TABLE(i2c, sc16is7xx_i2c_id_table);

static struct i2c_driver sc16is7xx_i2c_uart_driver = {
        .driver = {
                .name           = SC16IS7XX_NAME,
                .of_match_table = of_match_ptr(sc16is7xx_dt_ids),
        },
        .probe          = sc16is7xx_i2c_probe,
        .remove         = sc16is7xx_i2c_remove,
        .id_table       = sc16is7xx_i2c_id_table,
};

#endif

static int __init sc16is7xx_init(void)
{
        int ret;

        ret = uart_register_driver(&sc16is7xx_uart);
        if (ret) {
                pr_err("Registering UART driver failed\n");
                return ret;
        }

#ifdef CONFIG_SERIAL_SC16IS7XX_I2C
        ret = i2c_add_driver(&sc16is7xx_i2c_uart_driver);
        if (ret < 0) {
                pr_err("failed to init sc16is7xx i2c --> %d\n", ret);
                return ret;
        }
#endif

#ifdef CONFIG_SERIAL_SC16IS7XX_SPI
        ret = spi_register_driver(&sc16is7xx_spi_uart_driver);
        if (ret < 0) {
                pr_err("failed to init sc16is7xx spi --> %d\n", ret);
                return ret;
        }
#endif
        return ret;
}
module_init(sc16is7xx_init);

static void __exit sc16is7xx_exit(void)
{
#ifdef CONFIG_SERIAL_SC16IS7XX_I2C
        i2c_del_driver(&sc16is7xx_i2c_uart_driver);
#endif

#ifdef CONFIG_SERIAL_SC16IS7XX_SPI
        spi_unregister_driver(&sc16is7xx_spi_uart_driver);
#endif
        uart_unregister_driver(&sc16is7xx_uart);
}
module_exit(sc16is7xx_exit);

MODULE_LICENSE("GPL");
MODULE_AUTHOR("Jon Ringle <jringle@gridpoint.com>");
MODULE_DESCRIPTION("SC16IS7XX serial driver");