1/* 2 * Copyright (C) 2007-2009 ST-Ericsson AB 3 * License terms: GNU General Public License (GPL) version 2 4 * 5 * ABX500 core access functions. 6 * The abx500 interface is used for the Analog Baseband chips. 7 * 8 * Author: Mattias Wallin <mattias.wallin@stericsson.com> 9 * Author: Mattias Nilsson <mattias.i.nilsson@stericsson.com> 10 * Author: Bengt Jonsson <bengt.g.jonsson@stericsson.com> 11 * Author: Rickard Andersson <rickard.andersson@stericsson.com> 12 */ 13 14#include <linux/regulator/machine.h> 15 16struct device; 17 18#ifndef MFD_ABX500_H 19#define MFD_ABX500_H 20 21/** 22 * struct abx500_init_setting 23 * Initial value of the registers for driver to use during setup. 24 */ 25struct abx500_init_settings { 26 u8 bank; 27 u8 reg; 28 u8 setting; 29}; 30 31/* Battery driver related data */ 32/* 33 * ADC for the battery thermistor. 34 * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined 35 * with a NTC resistor to both identify the battery and to measure its 36 * temperature. Different phone manufactures uses different techniques to both 37 * identify the battery and to read its temperature. 38 */ 39enum abx500_adc_therm { 40 ABx500_ADC_THERM_BATCTRL, 41 ABx500_ADC_THERM_BATTEMP, 42}; 43 44/** 45 * struct abx500_res_to_temp - defines one point in a temp to res curve. To 46 * be used in battery packs that combines the identification resistor with a 47 * NTC resistor. 48 * @temp: battery pack temperature in Celcius 49 * @resist: NTC resistor net total resistance 50 */ 51struct abx500_res_to_temp { 52 int temp; 53 int resist; 54}; 55 56/** 57 * struct abx500_v_to_cap - Table for translating voltage to capacity 58 * @voltage: Voltage in mV 59 * @capacity: Capacity in percent 60 */ 61struct abx500_v_to_cap { 62 int voltage; 63 int capacity; 64}; 65 66/* Forward declaration */ 67struct abx500_fg; 68 69/** 70 * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds 71 * if not specified 72 * @recovery_sleep_timer: Time between measurements while recovering 73 * @recovery_total_time: Total recovery time 74 * @init_timer: Measurement interval during startup 75 * @init_discard_time: Time we discard voltage measurement at startup 76 * @init_total_time: Total init time during startup 77 * @high_curr_time: Time current has to be high to go to recovery 78 * @accu_charging: FG accumulation time while charging 79 * @accu_high_curr: FG accumulation time in high current mode 80 * @high_curr_threshold: High current threshold, in mA 81 * @lowbat_threshold: Low battery threshold, in mV 82 * @overbat_threshold: Over battery threshold, in mV 83 * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0 84 * Resolution in 50 mV step. 85 * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1 86 * Resolution in 50 mV step. 87 * @user_cap_limit Capacity reported from user must be within this 88 * limit to be considered as sane, in percentage 89 * points. 90 * @maint_thres This is the threshold where we stop reporting 91 * battery full while in maintenance, in per cent 92 * @pcut_enable: Enable power cut feature in ab8505 93 * @pcut_max_time: Max time threshold 94 * @pcut_flag_time: Flagtime threshold 95 * @pcut_max_restart: Max number of restarts 96 * @pcut_debounce_time: Sets battery debounce time 97 */ 98struct abx500_fg_parameters { 99 int recovery_sleep_timer; 100 int recovery_total_time; 101 int init_timer; 102 int init_discard_time; 103 int init_total_time; 104 int high_curr_time; 105 int accu_charging; 106 int accu_high_curr; 107 int high_curr_threshold; 108 int lowbat_threshold; 109 int overbat_threshold; 110 int battok_falling_th_sel0; 111 int battok_raising_th_sel1; 112 int user_cap_limit; 113 int maint_thres; 114 bool pcut_enable; 115 u8 pcut_max_time; 116 u8 pcut_flag_time; 117 u8 pcut_max_restart; 118 u8 pcut_debounce_time; 119}; 120 121/** 122 * struct abx500_charger_maximization - struct used by the board config. 123 * @use_maxi: Enable maximization for this battery type 124 * @maxi_chg_curr: Maximum charger current allowed 125 * @maxi_wait_cycles: cycles to wait before setting charger current 126 * @charger_curr_step delta between two charger current settings (mA) 127 */ 128struct abx500_maxim_parameters { 129 bool ena_maxi; 130 int chg_curr; 131 int wait_cycles; 132 int charger_curr_step; 133}; 134 135/** 136 * struct abx500_battery_type - different batteries supported 137 * @name: battery technology 138 * @resis_high: battery upper resistance limit 139 * @resis_low: battery lower resistance limit 140 * @charge_full_design: Maximum battery capacity in mAh 141 * @nominal_voltage: Nominal voltage of the battery in mV 142 * @termination_vol: max voltage upto which battery can be charged 143 * @termination_curr battery charging termination current in mA 144 * @recharge_cap battery capacity limit that will trigger a new 145 * full charging cycle in the case where maintenan- 146 * -ce charging has been disabled 147 * @normal_cur_lvl: charger current in normal state in mA 148 * @normal_vol_lvl: charger voltage in normal state in mV 149 * @maint_a_cur_lvl: charger current in maintenance A state in mA 150 * @maint_a_vol_lvl: charger voltage in maintenance A state in mV 151 * @maint_a_chg_timer_h: charge time in maintenance A state 152 * @maint_b_cur_lvl: charger current in maintenance B state in mA 153 * @maint_b_vol_lvl: charger voltage in maintenance B state in mV 154 * @maint_b_chg_timer_h: charge time in maintenance B state 155 * @low_high_cur_lvl: charger current in temp low/high state in mA 156 * @low_high_vol_lvl: charger voltage in temp low/high state in mV' 157 * @battery_resistance: battery inner resistance in mOhm. 158 * @n_r_t_tbl_elements: number of elements in r_to_t_tbl 159 * @r_to_t_tbl: table containing resistance to temp points 160 * @n_v_cap_tbl_elements: number of elements in v_to_cap_tbl 161 * @v_to_cap_tbl: Voltage to capacity (in %) table 162 * @n_batres_tbl_elements number of elements in the batres_tbl 163 * @batres_tbl battery internal resistance vs temperature table 164 */ 165struct abx500_battery_type { 166 int name; 167 int resis_high; 168 int resis_low; 169 int charge_full_design; 170 int nominal_voltage; 171 int termination_vol; 172 int termination_curr; 173 int recharge_cap; 174 int normal_cur_lvl; 175 int normal_vol_lvl; 176 int maint_a_cur_lvl; 177 int maint_a_vol_lvl; 178 int maint_a_chg_timer_h; 179 int maint_b_cur_lvl; 180 int maint_b_vol_lvl; 181 int maint_b_chg_timer_h; 182 int low_high_cur_lvl; 183 int low_high_vol_lvl; 184 int battery_resistance; 185 int n_temp_tbl_elements; 186 const struct abx500_res_to_temp *r_to_t_tbl; 187 int n_v_cap_tbl_elements; 188 const struct abx500_v_to_cap *v_to_cap_tbl; 189 int n_batres_tbl_elements; 190 const struct batres_vs_temp *batres_tbl; 191}; 192 193/** 194 * struct abx500_bm_capacity_levels - abx500 capacity level data 195 * @critical: critical capacity level in percent 196 * @low: low capacity level in percent 197 * @normal: normal capacity level in percent 198 * @high: high capacity level in percent 199 * @full: full capacity level in percent 200 */ 201struct abx500_bm_capacity_levels { 202 int critical; 203 int low; 204 int normal; 205 int high; 206 int full; 207}; 208 209/** 210 * struct abx500_bm_charger_parameters - Charger specific parameters 211 * @usb_volt_max: maximum allowed USB charger voltage in mV 212 * @usb_curr_max: maximum allowed USB charger current in mA 213 * @ac_volt_max: maximum allowed AC charger voltage in mV 214 * @ac_curr_max: maximum allowed AC charger current in mA 215 */ 216struct abx500_bm_charger_parameters { 217 int usb_volt_max; 218 int usb_curr_max; 219 int ac_volt_max; 220 int ac_curr_max; 221}; 222 223/** 224 * struct abx500_bm_data - abx500 battery management data 225 * @temp_under under this temp, charging is stopped 226 * @temp_low between this temp and temp_under charging is reduced 227 * @temp_high between this temp and temp_over charging is reduced 228 * @temp_over over this temp, charging is stopped 229 * @temp_now present battery temperature 230 * @temp_interval_chg temperature measurement interval in s when charging 231 * @temp_interval_nochg temperature measurement interval in s when not charging 232 * @main_safety_tmr_h safety timer for main charger 233 * @usb_safety_tmr_h safety timer for usb charger 234 * @bkup_bat_v voltage which we charge the backup battery with 235 * @bkup_bat_i current which we charge the backup battery with 236 * @no_maintenance indicates that maintenance charging is disabled 237 * @capacity_scaling indicates whether capacity scaling is to be used 238 * @abx500_adc_therm placement of thermistor, batctrl or battemp adc 239 * @chg_unknown_bat flag to enable charging of unknown batteries 240 * @enable_overshoot flag to enable VBAT overshoot control 241 * @auto_trig flag to enable auto adc trigger 242 * @fg_res resistance of FG resistor in 0.1mOhm 243 * @n_btypes number of elements in array bat_type 244 * @batt_id index of the identified battery in array bat_type 245 * @interval_charging charge alg cycle period time when charging (sec) 246 * @interval_not_charging charge alg cycle period time when not charging (sec) 247 * @temp_hysteresis temperature hysteresis 248 * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm) 249 * @n_chg_out_curr number of elements in array chg_output_curr 250 * @n_chg_in_curr number of elements in array chg_input_curr 251 * @chg_output_curr charger output current level map 252 * @chg_input_curr charger input current level map 253 * @maxi maximization parameters 254 * @cap_levels capacity in percent for the different capacity levels 255 * @bat_type table of supported battery types 256 * @chg_params charger parameters 257 * @fg_params fuel gauge parameters 258 */ 259struct abx500_bm_data { 260 int temp_under; 261 int temp_low; 262 int temp_high; 263 int temp_over; 264 int temp_now; 265 int temp_interval_chg; 266 int temp_interval_nochg; 267 int main_safety_tmr_h; 268 int usb_safety_tmr_h; 269 int bkup_bat_v; 270 int bkup_bat_i; 271 bool autopower_cfg; 272 bool ac_enabled; 273 bool usb_enabled; 274 bool usb_power_path; 275 bool no_maintenance; 276 bool capacity_scaling; 277 bool chg_unknown_bat; 278 bool enable_overshoot; 279 bool auto_trig; 280 enum abx500_adc_therm adc_therm; 281 int fg_res; 282 int n_btypes; 283 int batt_id; 284 int interval_charging; 285 int interval_not_charging; 286 int temp_hysteresis; 287 int gnd_lift_resistance; 288 int n_chg_out_curr; 289 int n_chg_in_curr; 290 int *chg_output_curr; 291 int *chg_input_curr; 292 const struct abx500_maxim_parameters *maxi; 293 const struct abx500_bm_capacity_levels *cap_levels; 294 struct abx500_battery_type *bat_type; 295 const struct abx500_bm_charger_parameters *chg_params; 296 const struct abx500_fg_parameters *fg_params; 297}; 298 299enum { 300 NTC_EXTERNAL = 0, 301 NTC_INTERNAL, 302}; 303 304int ab8500_bm_of_probe(struct device *dev, 305 struct device_node *np, 306 struct abx500_bm_data *bm); 307 308int abx500_set_register_interruptible(struct device *dev, u8 bank, u8 reg, 309 u8 value); 310int abx500_get_register_interruptible(struct device *dev, u8 bank, u8 reg, 311 u8 *value); 312int abx500_get_register_page_interruptible(struct device *dev, u8 bank, 313 u8 first_reg, u8 *regvals, u8 numregs); 314int abx500_set_register_page_interruptible(struct device *dev, u8 bank, 315 u8 first_reg, u8 *regvals, u8 numregs); 316/** 317 * abx500_mask_and_set_register_inerruptible() - Modifies selected bits of a 318 * target register 319 * 320 * @dev: The AB sub device. 321 * @bank: The i2c bank number. 322 * @bitmask: The bit mask to use. 323 * @bitvalues: The new bit values. 324 * 325 * Updates the value of an AB register: 326 * value -> ((value & ~bitmask) | (bitvalues & bitmask)) 327 */ 328int abx500_mask_and_set_register_interruptible(struct device *dev, u8 bank, 329 u8 reg, u8 bitmask, u8 bitvalues); 330int abx500_get_chip_id(struct device *dev); 331int abx500_event_registers_startup_state_get(struct device *dev, u8 *event); 332int abx500_startup_irq_enabled(struct device *dev, unsigned int irq); 333 334struct abx500_ops { 335 int (*get_chip_id) (struct device *); 336 int (*get_register) (struct device *, u8, u8, u8 *); 337 int (*set_register) (struct device *, u8, u8, u8); 338 int (*get_register_page) (struct device *, u8, u8, u8 *, u8); 339 int (*set_register_page) (struct device *, u8, u8, u8 *, u8); 340 int (*mask_and_set_register) (struct device *, u8, u8, u8, u8); 341 int (*event_registers_startup_state_get) (struct device *, u8 *); 342 int (*startup_irq_enabled) (struct device *, unsigned int); 343 void (*dump_all_banks) (struct device *); 344}; 345 346int abx500_register_ops(struct device *core_dev, struct abx500_ops *ops); 347void abx500_remove_ops(struct device *dev); 348#endif 349