LXR linux/include/linux/wm97xx.h

   1
   2/*
   3 * Register bits and API for Wolfson WM97xx series of codecs
   4 */
   5
   6#ifndef _LINUX_WM97XX_H
   7#define _LINUX_WM97XX_H
   8
   9#include <sound/core.h>
  10#include <sound/pcm.h>
  11#include <sound/ac97_codec.h>
  12#include <sound/initval.h>
  13#include <linux/types.h>
  14#include <linux/list.h>
  15#include <linux/input.h>        /* Input device layer */
  16#include <linux/platform_device.h>
  17
  18/*
  19 * WM97xx variants
  20 */
  21#define WM97xx_GENERIC                  0x0000
  22#define WM97xx_WM1613                   0x1613
  23
  24/*
  25 * WM97xx AC97 Touchscreen registers
  26 */
  27#define AC97_WM97XX_DIGITISER1          0x76
  28#define AC97_WM97XX_DIGITISER2          0x78
  29#define AC97_WM97XX_DIGITISER_RD        0x7a
  30#define AC97_WM9713_DIG1                0x74
  31#define AC97_WM9713_DIG2                AC97_WM97XX_DIGITISER1
  32#define AC97_WM9713_DIG3                AC97_WM97XX_DIGITISER2
  33
  34/*
  35 * WM97xx register bits
  36 */
  37#define WM97XX_POLL             0x8000  /* initiate a polling measurement */
  38#define WM97XX_ADCSEL_X         0x1000  /* x coord measurement */
  39#define WM97XX_ADCSEL_Y         0x2000  /* y coord measurement */
  40#define WM97XX_ADCSEL_PRES      0x3000  /* pressure measurement */
  41#define WM97XX_AUX_ID1          0x4000
  42#define WM97XX_AUX_ID2          0x5000
  43#define WM97XX_AUX_ID3          0x6000
  44#define WM97XX_AUX_ID4          0x7000
  45#define WM97XX_ADCSEL_MASK      0x7000  /* ADC selection mask */
  46#define WM97XX_COO              0x0800  /* enable coordinate mode */
  47#define WM97XX_CTC              0x0400  /* enable continuous mode */
  48#define WM97XX_CM_RATE_93       0x0000  /* 93.75Hz continuous rate */
  49#define WM97XX_CM_RATE_187      0x0100  /* 187.5Hz continuous rate */
  50#define WM97XX_CM_RATE_375      0x0200  /* 375Hz continuous rate */
  51#define WM97XX_CM_RATE_750      0x0300  /* 750Hz continuous rate */
  52#define WM97XX_CM_RATE_8K       0x00f0  /* 8kHz continuous rate */
  53#define WM97XX_CM_RATE_12K      0x01f0  /* 12kHz continuous rate */
  54#define WM97XX_CM_RATE_24K      0x02f0  /* 24kHz continuous rate */
  55#define WM97XX_CM_RATE_48K      0x03f0  /* 48kHz continuous rate */
  56#define WM97XX_CM_RATE_MASK     0x03f0
  57#define WM97XX_RATE(i)          (((i & 3) << 8) | ((i & 4) ? 0xf0 : 0))
  58#define WM97XX_DELAY(i)         ((i << 4) & 0x00f0)     /* sample delay times */
  59#define WM97XX_DELAY_MASK       0x00f0
  60#define WM97XX_SLEN             0x0008  /* slot read back enable */
  61#define WM97XX_SLT(i)           ((i - 5) & 0x7) /* panel slot (5-11) */
  62#define WM97XX_SLT_MASK         0x0007
  63#define WM97XX_PRP_DETW         0x4000  /* detect on, digitise off, wake */
  64#define WM97XX_PRP_DET          0x8000  /* detect on, digitise off, no wake */
  65#define WM97XX_PRP_DET_DIG      0xc000  /* setect on, digitise on */
  66#define WM97XX_RPR              0x2000  /* wake up on pen down */
  67#define WM97XX_PEN_DOWN         0x8000  /* pen is down */
  68
  69/* WM9712 Bits */
  70#define WM9712_45W              0x1000  /* set for 5-wire touchscreen */
  71#define WM9712_PDEN             0x0800  /* measure only when pen down */
  72#define WM9712_WAIT             0x0200  /* wait until adc is read before next sample */
  73#define WM9712_PIL              0x0100  /* current used for pressure measurement. set 400uA else 200uA */
  74#define WM9712_MASK_HI          0x0040  /* hi on mask pin (47) stops conversions */
  75#define WM9712_MASK_EDGE        0x0080  /* rising/falling edge on pin delays sample */
  76#define WM9712_MASK_SYNC        0x00c0  /* rising/falling edge on mask initiates sample */
  77#define WM9712_RPU(i)           (i&0x3f)        /* internal pull up on pen detect (64k / rpu) */
  78#define WM9712_PD(i)            (0x1 << i)      /* power management */
  79
  80/* WM9712 Registers */
  81#define AC97_WM9712_POWER       0x24
  82#define AC97_WM9712_REV         0x58
  83
  84/* WM9705 Bits */
  85#define WM9705_PDEN             0x1000  /* measure only when pen is down */
  86#define WM9705_PINV             0x0800  /* inverts sense of pen down output */
  87#define WM9705_BSEN             0x0400  /* BUSY flag enable, pin47 is 1 when busy */
  88#define WM9705_BINV             0x0200  /* invert BUSY (pin47) output */
  89#define WM9705_WAIT             0x0100  /* wait until adc is read before next sample */
  90#define WM9705_PIL              0x0080  /* current used for pressure measurement. set 400uA else 200uA */
  91#define WM9705_PHIZ             0x0040  /* set PHONE and PCBEEP inputs to high impedance */
  92#define WM9705_MASK_HI          0x0010  /* hi on mask stops conversions */
  93#define WM9705_MASK_EDGE        0x0020  /* rising/falling edge on pin delays sample */
  94#define WM9705_MASK_SYNC        0x0030  /* rising/falling edge on mask initiates sample */
  95#define WM9705_PDD(i)           (i & 0x000f)    /* pen detect comparator threshold */
  96
  97
  98/* WM9713 Bits */
  99#define WM9713_PDPOL            0x0400  /* Pen down polarity */
 100#define WM9713_POLL             0x0200  /* initiate a polling measurement */
 101#define WM9713_CTC              0x0100  /* enable continuous mode */
 102#define WM9713_ADCSEL_X         0x0002  /* X measurement */
 103#define WM9713_ADCSEL_Y         0x0004  /* Y measurement */
 104#define WM9713_ADCSEL_PRES      0x0008  /* Pressure measurement */
 105#define WM9713_COO              0x0001  /* enable coordinate mode */
 106#define WM9713_45W              0x1000  /* set for 5 wire panel */
 107#define WM9713_PDEN             0x0800  /* measure only when pen down */
 108#define WM9713_ADCSEL_MASK      0x00fe  /* ADC selection mask */
 109#define WM9713_WAIT             0x0200  /* coordinate wait */
 110
 111/* AUX ADC ID's */
 112#define TS_COMP1                0x0
 113#define TS_COMP2                0x1
 114#define TS_BMON                 0x2
 115#define TS_WIPER                0x3
 116
 117/* ID numbers */
 118#define WM97XX_ID1              0x574d
 119#define WM9712_ID2              0x4c12
 120#define WM9705_ID2              0x4c05
 121#define WM9713_ID2              0x4c13
 122
 123/* Codec GPIO's */
 124#define WM97XX_MAX_GPIO         16
 125#define WM97XX_GPIO_1           (1 << 1)
 126#define WM97XX_GPIO_2           (1 << 2)
 127#define WM97XX_GPIO_3           (1 << 3)
 128#define WM97XX_GPIO_4           (1 << 4)
 129#define WM97XX_GPIO_5           (1 << 5)
 130#define WM97XX_GPIO_6           (1 << 6)
 131#define WM97XX_GPIO_7           (1 << 7)
 132#define WM97XX_GPIO_8           (1 << 8)
 133#define WM97XX_GPIO_9           (1 << 9)
 134#define WM97XX_GPIO_10          (1 << 10)
 135#define WM97XX_GPIO_11          (1 << 11)
 136#define WM97XX_GPIO_12          (1 << 12)
 137#define WM97XX_GPIO_13          (1 << 13)
 138#define WM97XX_GPIO_14          (1 << 14)
 139#define WM97XX_GPIO_15          (1 << 15)
 140
 141
 142#define AC97_LINK_FRAME         21      /* time in uS for AC97 link frame */
 143
 144
 145/*---------------- Return codes from sample reading functions ---------------*/
 146
 147/* More data is available; call the sample gathering function again */
 148#define RC_AGAIN                        0x00000001
 149/* The returned sample is valid */
 150#define RC_VALID                        0x00000002
 151/* The pen is up (the first RC_VALID without RC_PENUP means pen is down) */
 152#define RC_PENUP                        0x00000004
 153/* The pen is down (RC_VALID implies RC_PENDOWN, but sometimes it is helpful
 154   to tell the handler that the pen is down but we don't know yet his coords,
 155   so the handler should not sleep or wait for pendown irq) */
 156#define RC_PENDOWN                      0x00000008
 157
 158/*
 159 * The wm97xx driver provides a private API for writing platform-specific
 160 * drivers.
 161 */
 162
 163/* The structure used to return arch specific sampled data into */
 164struct wm97xx_data {
 165    int x;
 166    int y;
 167    int p;
 168};
 169
 170/*
 171 * Codec GPIO status
 172 */
 173enum wm97xx_gpio_status {
 174    WM97XX_GPIO_HIGH,
 175    WM97XX_GPIO_LOW
 176};
 177
 178/*
 179 * Codec GPIO direction
 180 */
 181enum wm97xx_gpio_dir {
 182    WM97XX_GPIO_IN,
 183    WM97XX_GPIO_OUT
 184};
 185
 186/*
 187 * Codec GPIO polarity
 188 */
 189enum wm97xx_gpio_pol {
 190    WM97XX_GPIO_POL_HIGH,
 191    WM97XX_GPIO_POL_LOW
 192};
 193
 194/*
 195 * Codec GPIO sticky
 196 */
 197enum wm97xx_gpio_sticky {
 198    WM97XX_GPIO_STICKY,
 199    WM97XX_GPIO_NOTSTICKY
 200};
 201
 202/*
 203 * Codec GPIO wake
 204 */
 205enum wm97xx_gpio_wake {
 206    WM97XX_GPIO_WAKE,
 207    WM97XX_GPIO_NOWAKE
 208};
 209
 210/*
 211 * Digitiser ioctl commands
 212 */
 213#define WM97XX_DIG_START        0x1
 214#define WM97XX_DIG_STOP         0x2
 215#define WM97XX_PHY_INIT         0x3
 216#define WM97XX_AUX_PREPARE      0x4
 217#define WM97XX_DIG_RESTORE      0x5
 218
 219struct wm97xx;
 220
 221extern struct wm97xx_codec_drv wm9705_codec;
 222extern struct wm97xx_codec_drv wm9712_codec;
 223extern struct wm97xx_codec_drv wm9713_codec;
 224
 225/*
 226 * Codec driver interface - allows mapping to WM9705/12/13 and newer codecs
 227 */
 228struct wm97xx_codec_drv {
 229        u16 id;
 230        char *name;
 231
 232        /* read 1 sample */
 233        int (*poll_sample) (struct wm97xx *, int adcsel, int *sample);
 234
 235        /* read X,Y,[P] in poll */
 236        int (*poll_touch) (struct wm97xx *, struct wm97xx_data *);
 237
 238        int (*acc_enable) (struct wm97xx *, int enable);
 239        void (*phy_init) (struct wm97xx *);
 240        void (*dig_enable) (struct wm97xx *, int enable);
 241        void (*dig_restore) (struct wm97xx *);
 242        void (*aux_prepare) (struct wm97xx *);
 243};
 244
 245
 246/* Machine specific and accelerated touch operations */
 247struct wm97xx_mach_ops {
 248
 249        /* accelerated touch readback - coords are transmited on AC97 link */
 250        int acc_enabled;
 251        void (*acc_pen_up) (struct wm97xx *);
 252        int (*acc_pen_down) (struct wm97xx *);
 253        int (*acc_startup) (struct wm97xx *);
 254        void (*acc_shutdown) (struct wm97xx *);
 255
 256        /* interrupt mask control - required for accelerated operation */
 257        void (*irq_enable) (struct wm97xx *, int enable);
 258
 259        /* GPIO pin used for accelerated operation */
 260        int irq_gpio;
 261
 262        /* pre and post sample - can be used to minimise any analog noise */
 263        void (*pre_sample) (int);  /* function to run before sampling */
 264        void (*post_sample) (int);  /* function to run after sampling */
 265};
 266
 267struct wm97xx {
 268        u16 dig[3], id, gpio[6], misc;  /* Cached codec registers */
 269        u16 dig_save[3];                /* saved during aux reading */
 270        struct wm97xx_codec_drv *codec; /* attached codec driver*/
 271        struct input_dev *input_dev;    /* touchscreen input device */
 272        struct snd_ac97 *ac97;          /* ALSA codec access */
 273        struct device *dev;             /* ALSA device */
 274        struct platform_device *battery_dev;
 275        struct platform_device *touch_dev;
 276        struct wm97xx_mach_ops *mach_ops;
 277        struct mutex codec_mutex;
 278        struct delayed_work ts_reader;  /* Used to poll touchscreen */
 279        unsigned long ts_reader_interval; /* Current interval for timer */
 280        unsigned long ts_reader_min_interval; /* Minimum interval */
 281        unsigned int pen_irq;           /* Pen IRQ number in use */
 282        struct workqueue_struct *ts_workq;
 283        struct work_struct pen_event_work;
 284        u16 acc_slot;                   /* AC97 slot used for acc touch data */
 285        u16 acc_rate;                   /* acc touch data rate */
 286        unsigned pen_is_down:1;         /* Pen is down */
 287        unsigned aux_waiting:1;         /* aux measurement waiting */
 288        unsigned pen_probably_down:1;   /* used in polling mode */
 289        u16 variant;                    /* WM97xx chip variant */
 290        u16 suspend_mode;               /* PRP in suspend mode */
 291};
 292
 293struct wm97xx_batt_pdata {
 294        int     batt_aux;
 295        int     temp_aux;
 296        int     charge_gpio;
 297        int     min_voltage;
 298        int     max_voltage;
 299        int     batt_div;
 300        int     batt_mult;
 301        int     temp_div;
 302        int     temp_mult;
 303        int     batt_tech;
 304        char    *batt_name;
 305};
 306
 307struct wm97xx_pdata {
 308        struct wm97xx_batt_pdata        *batt_pdata;    /* battery data */
 309};
 310
 311/*
 312 * Codec GPIO access (not supported on WM9705)
 313 * This can be used to set/get codec GPIO and Virtual GPIO status.
 314 */
 315enum wm97xx_gpio_status wm97xx_get_gpio(struct wm97xx *wm, u32 gpio);
 316void wm97xx_set_gpio(struct wm97xx *wm, u32 gpio,
 317                          enum wm97xx_gpio_status status);
 318void wm97xx_config_gpio(struct wm97xx *wm, u32 gpio,
 319                                     enum wm97xx_gpio_dir dir,
 320                                     enum wm97xx_gpio_pol pol,
 321                                     enum wm97xx_gpio_sticky sticky,
 322                                     enum wm97xx_gpio_wake wake);
 323
 324void wm97xx_set_suspend_mode(struct wm97xx *wm, u16 mode);
 325
 326/* codec AC97 IO access */
 327int wm97xx_reg_read(struct wm97xx *wm, u16 reg);
 328void wm97xx_reg_write(struct wm97xx *wm, u16 reg, u16 val);
 329
 330/* aux adc readback */
 331int wm97xx_read_aux_adc(struct wm97xx *wm, u16 adcsel);
 332
 333/* machine ops */
 334int wm97xx_register_mach_ops(struct wm97xx *, struct wm97xx_mach_ops *);
 335void wm97xx_unregister_mach_ops(struct wm97xx *);
 336
 337#endif
 338