/*
 *  linux/arch/arm/mm/proc-arm922.S: MMU functions for ARM922
 *
 *  Copyright (C) 1999,2000 ARM Limited
 *  Copyright (C) 2000 Deep Blue Solutions Ltd.
 *  Copyright (C) 2001 Altera Corporation
 *  hacked for non-paged-MM by Hyok S. Choi, 2003.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 *
 *
 * These are the low level assembler for performing cache and TLB
 * functions on the arm922.
 *
 *  CONFIG_CPU_ARM922_CPU_IDLE -> nohlt
 */
#include <linux/linkage.h>
#include <linux/init.h>
#include <asm/assembler.h>
#include <asm/hwcap.h>
#include <asm/pgtable-hwdef.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/ptrace.h>
#include "proc-macros.S"

/*
 * The size of one data cache line.
 */
#define CACHE_DLINESIZE 32

/*
 * The number of data cache segments.
 */
#define CACHE_DSEGMENTS 4

/*
 * The number of lines in a cache segment.
 */
#define CACHE_DENTRIES  64

/*
 * This is the size at which it becomes more efficient to
 * clean the whole cache, rather than using the individual
 * cache line maintenance instructions.  (I think this should
 * be 32768).
 */
#define CACHE_DLIMIT    8192


        .text
/*
 * cpu_arm922_proc_init()
 */
ENTRY(cpu_arm922_proc_init)
        ret     lr

/*
 * cpu_arm922_proc_fin()
 */
ENTRY(cpu_arm922_proc_fin)
        mrc     p15, 0, r0, c1, c0, 0           @ ctrl register
        bic     r0, r0, #0x1000                 @ ...i............
        bic     r0, r0, #0x000e                 @ ............wca.
        mcr     p15, 0, r0, c1, c0, 0           @ disable caches
        ret     lr

/*
 * cpu_arm922_reset(loc)
 *
 * Perform a soft reset of the system.  Put the CPU into the
 * same state as it would be if it had been reset, and branch
 * to what would be the reset vector.
 *
 * loc: location to jump to for soft reset
 */
        .align  5
        .pushsection    .idmap.text, "ax"
ENTRY(cpu_arm922_reset)
        mov     ip, #0
        mcr     p15, 0, ip, c7, c7, 0           @ invalidate I,D caches
        mcr     p15, 0, ip, c7, c10, 4          @ drain WB
#ifdef CONFIG_MMU
        mcr     p15, 0, ip, c8, c7, 0           @ invalidate I & D TLBs
#endif
        mrc     p15, 0, ip, c1, c0, 0           @ ctrl register
        bic     ip, ip, #0x000f                 @ ............wcam
        bic     ip, ip, #0x1100                 @ ...i...s........
        mcr     p15, 0, ip, c1, c0, 0           @ ctrl register
        ret     r0
ENDPROC(cpu_arm922_reset)
        .popsection

/*
 * cpu_arm922_do_idle()
 */
        .align  5
ENTRY(cpu_arm922_do_idle)
        mcr     p15, 0, r0, c7, c0, 4           @ Wait for interrupt
        ret     lr


#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH

/*
 *      flush_icache_all()
 *
 *      Unconditionally clean and invalidate the entire icache.
 */
ENTRY(arm922_flush_icache_all)
        mov     r0, #0
        mcr     p15, 0, r0, c7, c5, 0           @ invalidate I cache
        ret     lr
ENDPROC(arm922_flush_icache_all)

/*
 *      flush_user_cache_all()
 *
 *      Clean and invalidate all cache entries in a particular
 *      address space.
 */
ENTRY(arm922_flush_user_cache_all)
        /* FALLTHROUGH */

/*
 *      flush_kern_cache_all()
 *
 *      Clean and invalidate the entire cache.
 */
ENTRY(arm922_flush_kern_cache_all)
        mov     r2, #VM_EXEC
        mov     ip, #0
__flush_whole_cache:
        mov     r1, #(CACHE_DSEGMENTS - 1) << 5 @ 8 segments
1:      orr     r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries
2:      mcr     p15, 0, r3, c7, c14, 2          @ clean+invalidate D index
        subs    r3, r3, #1 << 26
        bcs     2b                              @ entries 63 to 0
        subs    r1, r1, #1 << 5
        bcs     1b                              @ segments 7 to 0
        tst     r2, #VM_EXEC
        mcrne   p15, 0, ip, c7, c5, 0           @ invalidate I cache
        mcrne   p15, 0, ip, c7, c10, 4          @ drain WB
        ret     lr

/*
 *      flush_user_cache_range(start, end, flags)
 *
 *      Clean and invalidate a range of cache entries in the
 *      specified address range.
 *
 *      - start - start address (inclusive)
 *      - end   - end address (exclusive)
 *      - flags - vm_flags describing address space
 */
ENTRY(arm922_flush_user_cache_range)
        mov     ip, #0
        sub     r3, r1, r0                      @ calculate total size
        cmp     r3, #CACHE_DLIMIT
        bhs     __flush_whole_cache

1:      mcr     p15, 0, r0, c7, c14, 1          @ clean+invalidate D entry
        tst     r2, #VM_EXEC
        mcrne   p15, 0, r0, c7, c5, 1           @ invalidate I entry
        add     r0, r0, #CACHE_DLINESIZE
        cmp     r0, r1
        blo     1b
        tst     r2, #VM_EXEC
        mcrne   p15, 0, ip, c7, c10, 4          @ drain WB
        ret     lr

/*
 *      coherent_kern_range(start, end)
 *
 *      Ensure coherency between the Icache and the Dcache in the
 *      region described by start, end.  If you have non-snooping
 *      Harvard caches, you need to implement this function.
 *
 *      - start - virtual start address
 *      - end   - virtual end address
 */
ENTRY(arm922_coherent_kern_range)
        /* FALLTHROUGH */

/*
 *      coherent_user_range(start, end)
 *
 *      Ensure coherency between the Icache and the Dcache in the
 *      region described by start, end.  If you have non-snooping
 *      Harvard caches, you need to implement this function.
 *
 *      - start - virtual start address
 *      - end   - virtual end address
 */
ENTRY(arm922_coherent_user_range)
        bic     r0, r0, #CACHE_DLINESIZE - 1
1:      mcr     p15, 0, r0, c7, c10, 1          @ clean D entry
        mcr     p15, 0, r0, c7, c5, 1           @ invalidate I entry
        add     r0, r0, #CACHE_DLINESIZE
        cmp     r0, r1
        blo     1b
        mcr     p15, 0, r0, c7, c10, 4          @ drain WB
        mov     r0, #0
        ret     lr

/*
 *      flush_kern_dcache_area(void *addr, size_t size)
 *
 *      Ensure no D cache aliasing occurs, either with itself or
 *      the I cache
 *
 *      - addr  - kernel address
 *      - size  - region size
 */
ENTRY(arm922_flush_kern_dcache_area)
        add     r1, r0, r1
1:      mcr     p15, 0, r0, c7, c14, 1          @ clean+invalidate D entry
        add     r0, r0, #CACHE_DLINESIZE
        cmp     r0, r1
        blo     1b
        mov     r0, #0
        mcr     p15, 0, r0, c7, c5, 0           @ invalidate I cache
        mcr     p15, 0, r0, c7, c10, 4          @ drain WB
        ret     lr

/*
 *      dma_inv_range(start, end)
 *
 *      Invalidate (discard) the specified virtual address range.
 *      May not write back any entries.  If 'start' or 'end'
 *      are not cache line aligned, those lines must be written
 *      back.
 *
 *      - start - virtual start address
 *      - end   - virtual end address
 *
 * (same as v4wb)
 */
arm922_dma_inv_range:
        tst     r0, #CACHE_DLINESIZE - 1
        bic     r0, r0, #CACHE_DLINESIZE - 1
        mcrne   p15, 0, r0, c7, c10, 1          @ clean D entry
        tst     r1, #CACHE_DLINESIZE - 1
        mcrne   p15, 0, r1, c7, c10, 1          @ clean D entry
1:      mcr     p15, 0, r0, c7, c6, 1           @ invalidate D entry
        add     r0, r0, #CACHE_DLINESIZE
        cmp     r0, r1
        blo     1b
        mcr     p15, 0, r0, c7, c10, 4          @ drain WB
        ret     lr

/*
 *      dma_clean_range(start, end)
 *
 *      Clean the specified virtual address range.
 *
 *      - start - virtual start address
 *      - end   - virtual end address
 *
 * (same as v4wb)
 */
arm922_dma_clean_range:
        bic     r0, r0, #CACHE_DLINESIZE - 1
1:      mcr     p15, 0, r0, c7, c10, 1          @ clean D entry
        add     r0, r0, #CACHE_DLINESIZE
        cmp     r0, r1
        blo     1b
        mcr     p15, 0, r0, c7, c10, 4          @ drain WB
        ret     lr

/*
 *      dma_flush_range(start, end)
 *
 *      Clean and invalidate the specified virtual address range.
 *
 *      - start - virtual start address
 *      - end   - virtual end address
 */
ENTRY(arm922_dma_flush_range)
        bic     r0, r0, #CACHE_DLINESIZE - 1
1:      mcr     p15, 0, r0, c7, c14, 1          @ clean+invalidate D entry
        add     r0, r0, #CACHE_DLINESIZE
        cmp     r0, r1
        blo     1b
        mcr     p15, 0, r0, c7, c10, 4          @ drain WB
        ret     lr

/*
 *      dma_map_area(start, size, dir)
 *      - start - kernel virtual start address
 *      - size  - size of region
 *      - dir   - DMA direction
 */
ENTRY(arm922_dma_map_area)
        add     r1, r1, r0
        cmp     r2, #DMA_TO_DEVICE
        beq     arm922_dma_clean_range
        bcs     arm922_dma_inv_range
        b       arm922_dma_flush_range
ENDPROC(arm922_dma_map_area)

/*
 *      dma_unmap_area(start, size, dir)
 *      - start - kernel virtual start address
 *      - size  - size of region
 *      - dir   - DMA direction
 */
ENTRY(arm922_dma_unmap_area)
        ret     lr
ENDPROC(arm922_dma_unmap_area)

        .globl  arm922_flush_kern_cache_louis
        .equ    arm922_flush_kern_cache_louis, arm922_flush_kern_cache_all

        @ define struct cpu_cache_fns (see <asm/cacheflush.h> and proc-macros.S)
        define_cache_functions arm922
#endif


ENTRY(cpu_arm922_dcache_clean_area)
#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH
1:      mcr     p15, 0, r0, c7, c10, 1          @ clean D entry
        add     r0, r0, #CACHE_DLINESIZE
        subs    r1, r1, #CACHE_DLINESIZE
        bhi     1b
#endif
        ret     lr

/* =============================== PageTable ============================== */

/*
 * cpu_arm922_switch_mm(pgd)
 *
 * Set the translation base pointer to be as described by pgd.
 *
 * pgd: new page tables
 */
        .align  5
ENTRY(cpu_arm922_switch_mm)
#ifdef CONFIG_MMU
        mov     ip, #0
#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH
        mcr     p15, 0, ip, c7, c6, 0           @ invalidate D cache
#else
@ && 'Clean & Invalidate whole DCache'
@ && Re-written to use Index Ops.
@ && Uses registers r1, r3 and ip

        mov     r1, #(CACHE_DSEGMENTS - 1) << 5 @ 4 segments
1:      orr     r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries
2:      mcr     p15, 0, r3, c7, c14, 2          @ clean & invalidate D index
        subs    r3, r3, #1 << 26
        bcs     2b                              @ entries 63 to 0
        subs    r1, r1, #1 << 5
        bcs     1b                              @ segments 7 to 0
#endif
        mcr     p15, 0, ip, c7, c5, 0           @ invalidate I cache
        mcr     p15, 0, ip, c7, c10, 4          @ drain WB
        mcr     p15, 0, r0, c2, c0, 0           @ load page table pointer
        mcr     p15, 0, ip, c8, c7, 0           @ invalidate I & D TLBs
#endif
        ret     lr

/*
 * cpu_arm922_set_pte_ext(ptep, pte, ext)
 *
 * Set a PTE and flush it out
 */
        .align  5
ENTRY(cpu_arm922_set_pte_ext)
#ifdef CONFIG_MMU
        armv3_set_pte_ext
        mov     r0, r0
        mcr     p15, 0, r0, c7, c10, 1          @ clean D entry
        mcr     p15, 0, r0, c7, c10, 4          @ drain WB
#endif /* CONFIG_MMU */
        ret     lr

        .type   __arm922_setup, #function
__arm922_setup:
        mov     r0, #0
        mcr     p15, 0, r0, c7, c7              @ invalidate I,D caches on v4
        mcr     p15, 0, r0, c7, c10, 4          @ drain write buffer on v4
#ifdef CONFIG_MMU
        mcr     p15, 0, r0, c8, c7              @ invalidate I,D TLBs on v4
#endif
        adr     r5, arm922_crval
        ldmia   r5, {r5, r6}
        mrc     p15, 0, r0, c1, c0              @ get control register v4
        bic     r0, r0, r5
        orr     r0, r0, r6
        ret     lr
        .size   __arm922_setup, . - __arm922_setup

        /*
         *  R
         * .RVI ZFRS BLDP WCAM
         * ..11 0001 ..11 0101
         * 
         */
        .type   arm922_crval, #object
arm922_crval:
        crval   clear=0x00003f3f, mmuset=0x00003135, ucset=0x00001130

        __INITDATA
        @ define struct processor (see <asm/proc-fns.h> and proc-macros.S)
        define_processor_functions arm922, dabort=v4t_early_abort, pabort=legacy_pabort

        .section ".rodata"

        string  cpu_arch_name, "armv4t"
        string  cpu_elf_name, "v4"
        string  cpu_arm922_name, "ARM922T"

        .align

        .section ".proc.info.init", #alloc

        .type   __arm922_proc_info,#object
__arm922_proc_info:
        .long   0x41009220
        .long   0xff00fff0
        .long   PMD_TYPE_SECT | \
                PMD_SECT_BUFFERABLE | \
                PMD_SECT_CACHEABLE | \
                PMD_BIT4 | \
                PMD_SECT_AP_WRITE | \
                PMD_SECT_AP_READ
        .long   PMD_TYPE_SECT | \
                PMD_BIT4 | \
                PMD_SECT_AP_WRITE | \
                PMD_SECT_AP_READ
        initfn  __arm922_setup, __arm922_proc_info
        .long   cpu_arch_name
        .long   cpu_elf_name
        .long   HWCAP_SWP | HWCAP_HALF | HWCAP_THUMB
        .long   cpu_arm922_name
        .long   arm922_processor_functions
        .long   v4wbi_tlb_fns
        .long   v4wb_user_fns
#ifndef CONFIG_CPU_DCACHE_WRITETHROUGH
        .long   arm922_cache_fns
#else
        .long   v4wt_cache_fns
#endif
        .size   __arm922_proc_info, . - __arm922_proc_info