LXR linux/drivers/net/ethernet/freescale/Kconfig

   1#
   2# Freescale device configuration
   3#
   4
   5config NET_VENDOR_FREESCALE
   6        bool "Freescale devices"
   7        default y
   8        depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
   9                   M523x || M527x || M5272 || M528x || M520x || M532x || \
  10                   ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \
  11                   ARCH_LAYERSCAPE
  12        ---help---
  13          If you have a network (Ethernet) card belonging to this class, say Y.
  14
  15          Note that the answer to this question doesn't directly affect the
  16          kernel: saying N will just cause the configurator to skip all
  17          the questions about Freescale devices. If you say Y, you will be
  18          asked for your specific card in the following questions.
  19
  20if NET_VENDOR_FREESCALE
  21
  22config FEC
  23        tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
  24        depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
  25                   ARCH_MXC || SOC_IMX28)
  26        default ARCH_MXC || SOC_IMX28 if ARM
  27        select PHYLIB
  28        select PTP_1588_CLOCK
  29        ---help---
  30          Say Y here if you want to use the built-in 10/100 Fast ethernet
  31          controller on some Motorola ColdFire and Freescale i.MX processors.
  32
  33config FEC_MPC52xx
  34        tristate "FEC MPC52xx driver"
  35        depends on PPC_MPC52xx && PPC_BESTCOMM
  36        select CRC32
  37        select PHYLIB
  38        select PPC_BESTCOMM_FEC
  39        ---help---
  40          This option enables support for the MPC5200's on-chip
  41          Fast Ethernet Controller
  42          If compiled as module, it will be called fec_mpc52xx.
  43
  44config FEC_MPC52xx_MDIO
  45        bool "FEC MPC52xx MDIO bus driver"
  46        depends on FEC_MPC52xx
  47        default y
  48        ---help---
  49          The MPC5200's FEC can connect to the Ethernet either with
  50          an external MII PHY chip or 10 Mbps 7-wire interface
  51          (Motorola? industry standard).
  52          If your board uses an external PHY connected to FEC, enable this.
  53          If not sure, enable.
  54          If compiled as module, it will be called fec_mpc52xx_phy.
  55
  56source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
  57source "drivers/net/ethernet/freescale/fman/Kconfig"
  58
  59config FSL_PQ_MDIO
  60        tristate "Freescale PQ MDIO"
  61        select PHYLIB
  62        ---help---
  63          This driver supports the MDIO bus used by the gianfar and UCC drivers.
  64
  65config FSL_XGMAC_MDIO
  66        tristate "Freescale XGMAC MDIO"
  67        select PHYLIB
  68        select OF_MDIO
  69        ---help---
  70          This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
  71          on the FMan mEMAC (which supports both Clauses 22 and 45)
  72
  73config UCC_GETH
  74        tristate "Freescale QE Gigabit Ethernet"
  75        depends on QUICC_ENGINE
  76        select FSL_PQ_MDIO
  77        select PHYLIB
  78        ---help---
  79          This driver supports the Gigabit Ethernet mode of the QUICC Engine,
  80          which is available on some Freescale SOCs.
  81
  82config UGETH_TX_ON_DEMAND
  83        bool "Transmit on Demand support"
  84        depends on UCC_GETH
  85
  86config GIANFAR
  87        tristate "Gianfar Ethernet"
  88        select FSL_PQ_MDIO
  89        select PHYLIB
  90        select CRC32
  91        ---help---
  92          This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
  93          and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
  94          on the 8540.
  95
  96endif # NET_VENDOR_FREESCALE
  97