1
2
3
4
5
6
7
8
9
10
11
12
13
14#include <linux/clk.h>
15#include <linux/delay.h>
16#include <linux/device.h>
17#include <linux/err.h>
18#include <linux/extcon.h>
19#include <linux/gpio/consumer.h>
20#include <linux/io.h>
21#include <linux/module.h>
22#include <linux/of.h>
23#include <linux/platform_device.h>
24#include <linux/reboot.h>
25#include <linux/regulator/consumer.h>
26#include <linux/reset.h>
27#include <linux/slab.h>
28#include <linux/usb.h>
29#include <linux/usb/ulpi.h>
30
31#define HSPHY_AHBBURST 0x0090
32#define HSPHY_AHBMODE 0x0098
33#define HSPHY_GENCONFIG 0x009c
34#define HSPHY_GENCONFIG_2 0x00a0
35
36#define HSPHY_USBCMD 0x0140
37#define HSPHY_ULPI_VIEWPORT 0x0170
38#define HSPHY_CTRL 0x0240
39
40#define HSPHY_TXFIFO_IDLE_FORCE_DIS BIT(4)
41#define HSPHY_SESS_VLD_CTRL_EN BIT(7)
42#define HSPHY_POR_ASSERT BIT(0)
43#define HSPHY_RETEN BIT(1)
44
45#define HSPHY_SESS_VLD_CTRL BIT(25)
46
47#define ULPI_PWR_CLK_MNG_REG 0x88
48#define ULPI_PWR_OTG_COMP_DISABLE BIT(0)
49
50#define ULPI_MISC_A 0x96
51#define ULPI_MISC_A_VBUSVLDEXTSEL BIT(1)
52#define ULPI_MISC_A_VBUSVLDEXT BIT(0)
53
54#define HSPHY_3P3_MIN 3050000
55#define HSPHY_3P3_MAX 3300000
56
57#define HSPHY_1P8_MIN 1800000
58#define HSPHY_1P8_MAX 1800000
59
60#define HSPHY_VDD_MIN 5
61#define HSPHY_VDD_MAX 7
62
63struct phy_8x16 {
64 struct usb_phy phy;
65 void __iomem *regs;
66 struct clk *core_clk;
67 struct clk *iface_clk;
68 struct regulator_bulk_data regulator[3];
69
70 struct reset_control *phy_reset;
71
72 struct extcon_dev *vbus_edev;
73 struct notifier_block vbus_notify;
74
75 struct gpio_desc *switch_gpio;
76 struct notifier_block reboot_notify;
77};
78
79static int phy_8x16_notify_connect(struct usb_phy *phy,
80 enum usb_device_speed speed)
81{
82 struct phy_8x16 *qphy = container_of(phy, struct phy_8x16, phy);
83 u32 val;
84
85 val = ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT;
86 usb_phy_io_write(&qphy->phy, val, ULPI_SET(ULPI_MISC_A));
87
88 val = readl(qphy->regs + HSPHY_USBCMD);
89 val |= HSPHY_SESS_VLD_CTRL;
90 writel(val, qphy->regs + HSPHY_USBCMD);
91
92 return 0;
93}
94
95static int phy_8x16_notify_disconnect(struct usb_phy *phy,
96 enum usb_device_speed speed)
97{
98 struct phy_8x16 *qphy = container_of(phy, struct phy_8x16, phy);
99 u32 val;
100
101 val = ULPI_MISC_A_VBUSVLDEXT | ULPI_MISC_A_VBUSVLDEXTSEL;
102 usb_phy_io_write(&qphy->phy, val, ULPI_CLR(ULPI_MISC_A));
103
104 val = readl(qphy->regs + HSPHY_USBCMD);
105 val &= ~HSPHY_SESS_VLD_CTRL;
106 writel(val, qphy->regs + HSPHY_USBCMD);
107
108 return 0;
109}
110
111static int phy_8x16_vbus_on(struct phy_8x16 *qphy)
112{
113 phy_8x16_notify_connect(&qphy->phy, USB_SPEED_UNKNOWN);
114
115
116 gpiod_set_value_cansleep(qphy->switch_gpio, 0);
117
118 return 0;
119}
120
121static int phy_8x16_vbus_off(struct phy_8x16 *qphy)
122{
123 phy_8x16_notify_disconnect(&qphy->phy, USB_SPEED_UNKNOWN);
124
125
126 gpiod_set_value_cansleep(qphy->switch_gpio, 1);
127
128 return 0;
129}
130
131static int phy_8x16_vbus_notify(struct notifier_block *nb, unsigned long event,
132 void *ptr)
133{
134 struct phy_8x16 *qphy = container_of(nb, struct phy_8x16, vbus_notify);
135
136 if (event)
137 phy_8x16_vbus_on(qphy);
138 else
139 phy_8x16_vbus_off(qphy);
140
141 return NOTIFY_DONE;
142}
143
144static int phy_8x16_init(struct usb_phy *phy)
145{
146 struct phy_8x16 *qphy = container_of(phy, struct phy_8x16, phy);
147 u32 val, init[] = {0x44, 0x6B, 0x24, 0x13};
148 u32 addr = ULPI_EXT_VENDOR_SPECIFIC;
149 int idx, state;
150
151 for (idx = 0; idx < ARRAY_SIZE(init); idx++)
152 usb_phy_io_write(phy, init[idx], addr + idx);
153
154 reset_control_reset(qphy->phy_reset);
155
156
157 val = readl(qphy->regs + HSPHY_CTRL);
158 val |= HSPHY_POR_ASSERT;
159 writel(val, qphy->regs + HSPHY_CTRL);
160
161
162
163
164
165
166 usleep_range(12, 15);
167
168
169 val = readl(qphy->regs + HSPHY_CTRL);
170 val &= ~HSPHY_POR_ASSERT;
171 writel(val, qphy->regs + HSPHY_CTRL);
172
173 usleep_range(10, 15);
174
175 writel(0x00, qphy->regs + HSPHY_AHBBURST);
176 writel(0x08, qphy->regs + HSPHY_AHBMODE);
177
178
179 val = readl(qphy->regs + HSPHY_GENCONFIG);
180 val &= ~HSPHY_TXFIFO_IDLE_FORCE_DIS;
181 writel(val, qphy->regs + HSPHY_GENCONFIG);
182
183 val = readl(qphy->regs + HSPHY_GENCONFIG_2);
184 val |= HSPHY_SESS_VLD_CTRL_EN;
185 writel(val, qphy->regs + HSPHY_GENCONFIG_2);
186
187 val = ULPI_PWR_OTG_COMP_DISABLE;
188 usb_phy_io_write(phy, val, ULPI_SET(ULPI_PWR_CLK_MNG_REG));
189
190 state = extcon_get_cable_state_(qphy->vbus_edev, EXTCON_USB);
191 if (state)
192 phy_8x16_vbus_on(qphy);
193 else
194 phy_8x16_vbus_off(qphy);
195
196 val = usb_phy_io_read(&qphy->phy, ULPI_FUNC_CTRL);
197 val &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
198 val |= ULPI_FUNC_CTRL_OPMODE_NORMAL;
199 usb_phy_io_write(&qphy->phy, val, ULPI_FUNC_CTRL);
200
201 return 0;
202}
203
204static void phy_8x16_shutdown(struct usb_phy *phy)
205{
206 u32 val;
207
208
209 val = usb_phy_io_read(phy, ULPI_FUNC_CTRL);
210 val &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
211 val |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING;
212 usb_phy_io_write(phy, val, ULPI_FUNC_CTRL);
213}
214
215static int phy_8x16_read_devicetree(struct phy_8x16 *qphy)
216{
217 struct device *dev = qphy->phy.dev;
218 int ret;
219
220 qphy->core_clk = devm_clk_get(dev, "core");
221 if (IS_ERR(qphy->core_clk))
222 return PTR_ERR(qphy->core_clk);
223
224 qphy->iface_clk = devm_clk_get(dev, "iface");
225 if (IS_ERR(qphy->iface_clk))
226 return PTR_ERR(qphy->iface_clk);
227
228 qphy->regulator[0].supply = "v3p3";
229 qphy->regulator[1].supply = "v1p8";
230 qphy->regulator[2].supply = "vddcx";
231
232 ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(qphy->regulator),
233 qphy->regulator);
234 if (ret)
235 return ret;
236
237 qphy->phy_reset = devm_reset_control_get(dev, "phy");
238 if (IS_ERR(qphy->phy_reset))
239 return PTR_ERR(qphy->phy_reset);
240
241 qphy->switch_gpio = devm_gpiod_get_optional(dev, "switch",
242 GPIOD_OUT_LOW);
243 return PTR_ERR_OR_ZERO(qphy->switch_gpio);
244}
245
246static int phy_8x16_reboot_notify(struct notifier_block *this,
247 unsigned long code, void *unused)
248{
249 struct phy_8x16 *qphy;
250
251 qphy = container_of(this, struct phy_8x16, reboot_notify);
252
253
254
255
256
257 gpiod_set_value_cansleep(qphy->switch_gpio, 0);
258 return NOTIFY_DONE;
259}
260
261static int phy_8x16_probe(struct platform_device *pdev)
262{
263 struct phy_8x16 *qphy;
264 struct resource *res;
265 struct usb_phy *phy;
266 int ret;
267
268 qphy = devm_kzalloc(&pdev->dev, sizeof(*qphy), GFP_KERNEL);
269 if (!qphy)
270 return -ENOMEM;
271
272 platform_set_drvdata(pdev, qphy);
273
274 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
275 if (!res)
276 return -EINVAL;
277
278 qphy->regs = devm_ioremap(&pdev->dev, res->start, resource_size(res));
279 if (!qphy->regs)
280 return -ENOMEM;
281
282 phy = &qphy->phy;
283 phy->dev = &pdev->dev;
284 phy->label = dev_name(&pdev->dev);
285 phy->init = phy_8x16_init;
286 phy->shutdown = phy_8x16_shutdown;
287 phy->notify_connect = phy_8x16_notify_connect;
288 phy->notify_disconnect = phy_8x16_notify_disconnect;
289 phy->io_priv = qphy->regs + HSPHY_ULPI_VIEWPORT;
290 phy->io_ops = &ulpi_viewport_access_ops;
291 phy->type = USB_PHY_TYPE_USB2;
292
293 ret = phy_8x16_read_devicetree(qphy);
294 if (ret < 0)
295 return ret;
296
297 qphy->vbus_edev = extcon_get_edev_by_phandle(phy->dev, 0);
298 if (IS_ERR(qphy->vbus_edev))
299 return PTR_ERR(qphy->vbus_edev);
300
301 ret = clk_set_rate(qphy->core_clk, INT_MAX);
302 if (ret < 0)
303 dev_dbg(phy->dev, "Can't boost core clock\n");
304
305 ret = clk_prepare_enable(qphy->core_clk);
306 if (ret < 0)
307 return ret;
308
309 ret = clk_prepare_enable(qphy->iface_clk);
310 if (ret < 0)
311 goto off_core;
312
313 ret = regulator_bulk_enable(ARRAY_SIZE(qphy->regulator),
314 qphy->regulator);
315 if (WARN_ON(ret))
316 goto off_clks;
317
318 qphy->vbus_notify.notifier_call = phy_8x16_vbus_notify;
319 ret = extcon_register_notifier(qphy->vbus_edev, EXTCON_USB,
320 &qphy->vbus_notify);
321 if (ret < 0)
322 goto off_power;
323
324 ret = usb_add_phy_dev(&qphy->phy);
325 if (ret)
326 goto off_extcon;
327
328 qphy->reboot_notify.notifier_call = phy_8x16_reboot_notify;
329 register_reboot_notifier(&qphy->reboot_notify);
330
331 return 0;
332
333off_extcon:
334 extcon_unregister_notifier(qphy->vbus_edev, EXTCON_USB,
335 &qphy->vbus_notify);
336off_power:
337 regulator_bulk_disable(ARRAY_SIZE(qphy->regulator), qphy->regulator);
338off_clks:
339 clk_disable_unprepare(qphy->iface_clk);
340off_core:
341 clk_disable_unprepare(qphy->core_clk);
342 return ret;
343}
344
345static int phy_8x16_remove(struct platform_device *pdev)
346{
347 struct phy_8x16 *qphy = platform_get_drvdata(pdev);
348
349 unregister_reboot_notifier(&qphy->reboot_notify);
350 extcon_unregister_notifier(qphy->vbus_edev, EXTCON_USB,
351 &qphy->vbus_notify);
352
353
354
355
356
357 gpiod_set_value_cansleep(qphy->switch_gpio, 0);
358
359 usb_remove_phy(&qphy->phy);
360
361 clk_disable_unprepare(qphy->iface_clk);
362 clk_disable_unprepare(qphy->core_clk);
363 regulator_bulk_disable(ARRAY_SIZE(qphy->regulator), qphy->regulator);
364 return 0;
365}
366
367static const struct of_device_id phy_8x16_dt_match[] = {
368 { .compatible = "qcom,usb-8x16-phy" },
369 { }
370};
371MODULE_DEVICE_TABLE(of, phy_8x16_dt_match);
372
373static struct platform_driver phy_8x16_driver = {
374 .probe = phy_8x16_probe,
375 .remove = phy_8x16_remove,
376 .driver = {
377 .name = "phy-qcom-8x16-usb",
378 .of_match_table = phy_8x16_dt_match,
379 },
380};
381module_platform_driver(phy_8x16_driver);
382
383MODULE_LICENSE("GPL v2");
384MODULE_DESCRIPTION("Qualcomm APQ8016/MSM8916 chipsets USB transceiver driver");
385
