1
2if ETRAX_ARCH_V32
3
4source arch/cris/arch-v32/mach-fs/Kconfig
5source arch/cris/arch-v32/mach-a3/Kconfig
6
7source drivers/cpufreq/Kconfig
8
9config ETRAX_DRAM_VIRTUAL_BASE
10 hex
11 depends on ETRAX_ARCH_V32
12 default "c0000000"
13
14choice
15 prompt "Kernel GDB port"
16 depends on ETRAX_KGDB
17 default ETRAX_KGDB_PORT0
18 help
19 Choose a serial port for kernel debugging. NOTE: This port should
20 not be enabled under Drivers for built-in interfaces (as it has its
21 own initialization code) and should not be the same as the debug port.
22
23config ETRAX_KGDB_PORT4
24 bool "Serial-4"
25 depends on ETRAX_SERIAL_PORTS = 5
26 help
27 Use serial port 4 for kernel debugging.
28
29endchoice
30
31config ETRAX_MEM_GRP1_CONFIG
32 hex "MEM_GRP1_CONFIG"
33 depends on ETRAX_ARCH_V32
34 default "4044a"
35 help
36 Waitstates for flash. The default value is suitable for the
37 standard flashes used in axis products (120 ns).
38
39config ETRAX_MEM_GRP2_CONFIG
40 hex "MEM_GRP2_CONFIG"
41 depends on ETRAX_ARCH_V32
42 default "0"
43 help
44 Waitstates for SRAM. 0 is a good choice for most Axis products.
45
46config ETRAX_MEM_GRP3_CONFIG
47 hex "MEM_GRP3_CONFIG"
48 depends on ETRAX_ARCH_V32
49 default "0"
50 help
51 Waitstates for CSP0-3. 0 is a good choice for most Axis products.
52 It may need to be changed if external devices such as extra
53 register-mapped LEDs are used.
54
55config ETRAX_MEM_GRP4_CONFIG
56 hex "MEM_GRP4_CONFIG"
57 depends on ETRAX_ARCH_V32
58 default "0"
59 help
60 Waitstates for CSP4-6. 0 is a good choice for most Axis products.
61
62config ETRAX_SDRAM_GRP0_CONFIG
63 hex "SDRAM_GRP0_CONFIG"
64 depends on ETRAX_ARCH_V32
65 default "336"
66 help
67 SDRAM configuration for group 0. The value depends on the
68 hardware configuration. The default value is suitable
69 for 32 MB organized as two 16 bits chips (e.g. Axis
70 part number 18550) connected as one 32 bit device (i.e. in
71 the same group).
72
73config ETRAX_SDRAM_GRP1_CONFIG
74 hex "SDRAM_GRP1_CONFIG"
75 depends on ETRAX_ARCH_V32
76 default "0"
77 help
78 SDRAM configuration for group 1. The default value is 0
79 because group 1 is not used in the default configuration,
80 described in the help for SDRAM_GRP0_CONFIG.
81
82config ETRAX_SDRAM_TIMING
83 hex "SDRAM_TIMING"
84 depends on ETRAX_ARCH_V32
85 default "104a"
86 help
87 SDRAM timing parameters. The default value is ok for
88 most hardwares but large SDRAMs may require a faster
89 refresh (a.k.a 8K refresh). The default value implies
90 100MHz clock and SDR mode.
91
92config ETRAX_SDRAM_COMMAND
93 hex "SDRAM_COMMAND"
94 depends on ETRAX_ARCH_V32
95 default "0"
96 help
97 SDRAM command. Should be 0 unless you really know what
98 you are doing (may be != 0 for unusual address line
99 mappings such as in a MCM)..
100
101config ETRAX_DEF_GIO_PA_OE
102 hex "GIO_PA_OE"
103 depends on ETRAX_ARCH_V32
104 default "1c"
105 help
106 Configures the direction of general port A bits. 1 is out, 0 is in.
107 This is often totally different depending on the product used.
108 There are some guidelines though - if you know that only LED's are
109 connected to port PA, then they are usually connected to bits 2-4
110 and you can therefore use 1c. On other boards which don't have the
111 LED's at the general ports, these bits are used for all kinds of
112 stuff. If you don't know what to use, it is always safe to put all
113 as inputs, although floating inputs isn't good.
114
115config ETRAX_DEF_GIO_PA_OUT
116 hex "GIO_PA_OUT"
117 depends on ETRAX_ARCH_V32
118 default "00"
119 help
120 Configures the initial data for the general port A bits. Most
121 products should use 00 here.
122
123config ETRAX_DEF_GIO_PB_OE
124 hex "GIO_PB_OE"
125 depends on ETRAX_ARCH_V32
126 default "00000"
127 help
128 Configures the direction of general port B bits. 1 is out, 0 is in.
129 This is often totally different depending on the product used.
130 There are some guidelines though - if you know that only LED's are
131 connected to port PA, then they are usually connected to bits 2-4
132 and you can therefore use 1c. On other boards which don't have the
133 LED's at the general ports, these bits are used for all kinds of
134 stuff. If you don't know what to use, it is always safe to put all
135 as inputs, although floating inputs isn't good.
136
137config ETRAX_DEF_GIO_PB_OUT
138 hex "GIO_PB_OUT"
139 depends on ETRAX_ARCH_V32
140 default "00000"
141 help
142 Configures the initial data for the general port B bits. Most
143 products should use 00000 here.
144
145config ETRAX_DEF_GIO_PC_OE
146 hex "GIO_PC_OE"
147 depends on ETRAX_ARCH_V32
148 default "00000"
149 help
150 Configures the direction of general port C bits. 1 is out, 0 is in.
151 This is often totally different depending on the product used.
152 There are some guidelines though - if you know that only LED's are
153 connected to port PA, then they are usually connected to bits 2-4
154 and you can therefore use 1c. On other boards which don't have the
155 LED's at the general ports, these bits are used for all kinds of
156 stuff. If you don't know what to use, it is always safe to put all
157 as inputs, although floating inputs isn't good.
158
159config ETRAX_DEF_GIO_PC_OUT
160 hex "GIO_PC_OUT"
161 depends on ETRAX_ARCH_V32
162 default "00000"
163 help
164 Configures the initial data for the general port C bits. Most
165 products should use 00000 here.
166
167config ETRAX_DEF_GIO_PD_OE
168 hex "GIO_PD_OE"
169 depends on ETRAX_ARCH_V32
170 default "00000"
171 help
172 Configures the direction of general port D bits. 1 is out, 0 is in.
173 This is often totally different depending on the product used.
174 There are some guidelines though - if you know that only LED's are
175 connected to port PA, then they are usually connected to bits 2-4
176 and you can therefore use 1c. On other boards which don't have the
177 LED's at the general ports, these bits are used for all kinds of
178 stuff. If you don't know what to use, it is always safe to put all
179 as inputs, although floating inputs isn't good.
180
181config ETRAX_DEF_GIO_PD_OUT
182 hex "GIO_PD_OUT"
183 depends on ETRAX_ARCH_V32
184 default "00000"
185 help
186 Configures the initial data for the general port D bits. Most
187 products should use 00000 here.
188
189config ETRAX_DEF_GIO_PE_OE
190 hex "GIO_PE_OE"
191 depends on ETRAX_ARCH_V32
192 default "00000"
193 help
194 Configures the direction of general port E bits. 1 is out, 0 is in.
195 This is often totally different depending on the product used.
196 There are some guidelines though - if you know that only LED's are
197 connected to port PA, then they are usually connected to bits 2-4
198 and you can therefore use 1c. On other boards which don't have the
199 LED's at the general ports, these bits are used for all kinds of
200 stuff. If you don't know what to use, it is always safe to put all
201 as inputs, although floating inputs isn't good.
202
203config ETRAX_DEF_GIO_PE_OUT
204 hex "GIO_PE_OUT"
205 depends on ETRAX_ARCH_V32
206 default "00000"
207 help
208 Configures the initial data for the general port E bits. Most
209 products should use 00000 here.
210
211endif
212
